Een IPsec-router met dynamische LAN-naar-LAN peer- en VPN-clients configureren
Inhoud
Inleiding
Deze configuratie toont een LAN-to-LAN configuratie tussen twee routers in een hub-spoke omgeving. Cisco VPN-clients maken ook verbinding met de hub en gebruiken uitgebreide verificatie (Xauth).
De spaak router in dit scenario verkrijgt zijn IP adres dynamisch via DHCP. Het gebruik van Dynamic Host Configuration Protocol (DHCP) is gebruikelijk in situaties waarin de spaak is verbonden met internet via een DSL- of kabelmodem. Dit komt doordat de ISP IP-adressen vaak dynamisch provisioneert met DHCP voor deze goedkope verbindingen.
Zonder verdere configuratie is het gebruik van een vooraf gedeelde sleutel met een wild-card op de hubrouter in deze situatie niet mogelijk. Dit komt doordat Xauth voor de VPN-clientverbindingen de LAN-to-LAN-verbinding verbreekt. Wanneer u Xauth echter uitschakelt, wordt de mogelijkheid om VPN-clients te verifiëren beperkt.
De introductie van ISAKMP-profielen in Cisco IOS® softwarerelease 12.2(15)T maakt deze configuratie mogelijk omdat u andere eigenschappen van de verbinding kunt matchen (VPN-clientgroep, peer IP-adres, volledig gekwalificeerde domeinnaam [FQDN], enzovoort) in plaats van alleen het peer IP-adres. ISAKMP-profielen zijn het onderwerp van deze configuratie.
Opmerking: u kunt ook het no-xauth-trefwoord gebruiken met de opdracht crypto isakmp key om Xauth voor LAN-to-LAN-peers te omzeilen. Raadpleeg Mogelijk om Xauth uit te schakelen voor statische IPsec-peers en IPsec tussen twee routers en een Cisco VPN-client 4.x te configureren voor meer informatie.
De spoke routerconfiguratie in dit document kan worden gerepliceerd op alle andere spoke routers die verbinding maken met dezelfde hub. Het enige verschil tussen spaken is de access-list die verwijst naar het te versleutelen verkeer.
Raadpleeg de EzVPN-client en -server op hetzelfde routerconfiguratievoorbeeld om meer te weten te komen over het scenario waarin u een router kunt configureren als een EzVPN-client en -server op dezelfde interface.
Raadpleeg LAN-to-LAN-tunnels op een VPN 3000 Concentrator waarbij een PIX-firewall voor DHCP is geconfigureerd om de Cisco VPN 3000 Concentrator Series te configureren om IPsec-tunnels dynamisch te maken met externe Cisco PIX-firewalls die DHCP gebruiken om IP-adressen op hun openbare interfaces te verkrijgen.
Raadpleeg IPsec LAN-to-LAN-tunnel op een VPN 3000 Concentrator met een Cisco IOS-router geconfigureerd voor DHCP-configuratie Voorbeeld om de VPN 3000 Concentrator Series te configureren om IPsec-tunnels dynamisch te maken met externe VPN-apparaten die dynamische IP-adressen op hun openbare interfaces ontvangen.
Raadpleeg IPsec tussen een statische IOS-router en een dynamisch PIX/ASA 7.x met NAT-configuratievoorbeeld om de PIX/ASA security applicatie in staat te stellen dynamische IPsec-verbindingen van de IOS® router te accepteren.
Voorwaarden
Vereisten
Er zijn geen specifieke vereisten van toepassing op dit document.
Gebruikte componenten
IPsec-profielen zijn geïntroduceerd in Cisco IOS-softwarerelease 12.2(15)T. Wegens Cisco bug-id CSC77140 (alleen geregistreerde klanten) moet u Cisco IOS-softwarerelease 12.3(3) of hoger, of Cisco IOS-softwarerelease 12.3(2)T of hoger, uitvoeren om deze configuratie succesvol te laten werken. Deze configuraties zijn getest met behulp van deze softwareversies:
-
Cisco IOS-softwarerelease 12.3(6a) op de hubrouter
-
Cisco IOS-softwarerelease 12.2(23a) op de spraakrouter (dit kan elke crypto-versie zijn)
-
Cisco VPN-client versie 4.0(4) onder Windows 2000
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u de potentiële impact van elke opdracht begrijpen.
Conventies
Configureren
Deze sectie bevat informatie over het configureren van de functies die in dit document worden beschreven.
Opmerking: Gebruik de Command Lookup Tool (alleen voor geregistreerde klanten) voor meer informatie over de opdrachten die in dit document worden gebruikt.
Netwerkdiagram
Dit document gebruikt de netwerkinstallatie die in dit diagram wordt getoond.
Configuraties
Het netwerk in dit document is als volgt opgebouwd:
| Hub-configuratie |
|---|
version 12.3 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Hub ! no logging on ! username gfullage password 7 0201024E070A0E2649 aaa new-model ! ! aaa authentication login clientauth local aaa authorization network groupauthor local aaa session-id common ip subnet-zero ! ! no ip domain lookup ! ! !--- Keyring that defines wildcard pre-shared key. crypto keyring spokes pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123 ! crypto isakmp policy 10 encr 3des authentication pre-share group 2 ! !--- VPN Client configuration for group "testgroup" !--- (this name is configured in the VPN Client). crypto isakmp client configuration group testgroup key cisco321 dns 1.1.1.1 2.2.2.2 wins 3.3.3.3 4.4.4.4 domain cisco.com pool ippool ! !--- Profile for LAN-to-LAN connection, that references !--- the wildcard pre-shared key and a wildcard !--- identity (this is what is broken in !--- Cisco bug ID CSCea77140) and no Xauth. crypto isakmp profile L2L description LAN-to-LAN for spoke router(s) connection keyring spokes match identity address 0.0.0.0 !--- Profile for VPN Client connections, that matches !--- the "testgroup" group and defines the Xauth properties. crypto isakmp profile VPNclient description VPN clients profile match identity group testgroup client authentication list clientauth isakmp authorization list groupauthor client configuration address respond ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! !--- Two instances of the dynamic crypto map !--- reference the two previous IPsec profiles. crypto dynamic-map dynmap 5 set transform-set myset set isakmp-profile VPNclient crypto dynamic-map dynmap 10 set transform-set myset set isakmp-profile L2L ! ! !--- Crypto-map only references the two !--- instances of the previous dynamic crypto map. crypto map mymap 10 ipsec-isakmp dynamic dynmap ! ! ! interface FastEthernet0/0 description Outside interface ip address 10.48.67.181 255.255.255.224 no ip mroute-cache duplex auto speed auto crypto map mymap ! interface FastEthernet0/1 description Inside interface ip address 10.1.1.1 255.255.254.0 duplex auto speed auto no keepalive ! ip local pool ippool 10.5.5.1 10.5.5.254 no ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 10.48.66.181 ! ! call rsvp-sync ! ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 escape-character 27 line aux 0 line vty 0 4 password 7 121A0C041104 ! ! end |
| Spraakconfiguratie |
|---|
version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Spoke ! no logging on ! ip subnet-zero no ip domain lookup ! ip cef ! ! crypto isakmp policy 10 encr 3des authentication pre-share group 2 crypto isakmp key cisco123 address 10.48.67.181 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! !--- Standard crypto map on the spoke router !--- that references the known hub IP address. crypto map mymap 10 ipsec-isakmp set peer 10.48.67.181 set transform-set myset match address 100 ! ! controller ISA 5/1 ! ! interface FastEthernet0/0 description Outside interface ip address dhcp duplex auto speed auto crypto map mymap ! interface FastEthernet0/1 description Inside interface ip address 10.2.2.2 255.255.255.0 duplex auto speed auto no keepalive ! interface ATM1/0 no ip address shutdown no atm ilmi-keepalive ! ip classless ip route 0.0.0.0 0.0.0.0 10.100.2.3 no ip http server no ip http secure-server ! ! !--- Standard access-list that references traffic to be !--- encrypted. This is the only thing that needs !--- to be changed between different spoke routers. access-list 100 permit ip 10.2.0.0 0.0.255.255 10.1.0.0 0.0.255.255 ! ! call rsvp-sync ! ! mgcp profile default ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 password cisco login ! ! end |
VPN-client
Maak een nieuwe verbinding ingang die verwijst naar het IP adres van de hub router. De groepsnaam in dit voorbeeld is "testgroep" en het wachtwoord is "cisco321". Dit kan worden gezien in de hubrouterconfiguratie.
Verifiëren
Gebruik deze sectie om te controleren of uw configuratie goed werkt.
Debug commando's die draaien op de hub router kunnen bevestigen dat de juiste parameters worden aangepast voor de spaak- en VPN-clientverbindingen.
De Output Interpreter Tool (OIT) (alleen voor geregistreerde klanten) ondersteunt bepaalde opdrachten met show. Gebruik de OIT om een analyse te bekijken van de output van de opdracht show.
Opmerking: raadpleeg Belangrijke informatie over debug-opdrachten voordat u debug-opdrachten gebruikt.
-
toon ip interface-Toont de IP adrestoewijzing aan de spaak router.
-
toon crypto isakmp als detail—Hier worden de IKE SA's weergegeven die zijn ingesteld tussen de IPsec-initiators. Bijvoorbeeld de spraakrouter en de VPN-client en de hubrouter.
-
toon crypto ipsec sa—Hier worden IPsec SA’s weergegeven die zijn ingesteld tussen de IPsec-initiators. Bijvoorbeeld de spraakrouter en de VPN-client en de hubrouter.
-
debug crypto isakmp-displays berichten over Internet Key Exchange (IKE) gebeurtenissen.
-
debug crypto ipsec—Hier worden IPsec-gebeurtenissen weergegeven.
-
debug crypto engine—Hier worden gebeurtenissen in crypto-engine weergegeven.
Dit is de uitvoer van de opdracht show ip interface f0/0.
spoke#show ip interface f0/0 FastEthernet0/1 is up, line protocol is up Internet address is 10.100.2.102/24 Broadcast address is 255.255.255.255 Address determined by DHCP
Dit is de uitvoer van de show crypto isakmp als detail opdracht.
hub#show crypto isakmp sa detail
Codes: C - IKE configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal
X - IKE Extended Authentication
psk - Preshared key, rsig - RSA signature
renc - RSA encryption
C-id Local Remote I-VRF Encr Hash Auth DH Lifetime Cap.
1 10.48.67.181 10.100.2.102 3des sha psk 2 04:15:43
2 10.48.67.181 10.51.82.100 3des sha 2 05:31:58 CX
Dit is de uitvoer van de opdracht show crypto ipsec sa.
hub#show crypto ipsec sa
interface: FastEthernet0/0
Crypto map tag: mymap, local addr. 10.48.67.181
protected vrf:
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (10.5.5.1/255.255.255.255/0/0)
current_peer: 10.51.82.100:500
PERMIT, flags={}
#pkts encaps: 8, #pkts encrypt: 8, #pkts digest 8
#pkts decaps: 189, #pkts decrypt: 189, #pkts verify 189
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.48.67.181, remote crypto endpt.: 10.51.82.100
path mtu 1500, ip mtu 1500
current outbound spi: B0C0F4AC
inbound esp sas:
spi: 0x7A1AB8F3(2048571635)
transform: esp-3des esp-sha-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2004, flow_id: 5, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4602415/3169)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0xB0C0F4AC(2965435564)
transform: esp-3des esp-sha-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2005, flow_id: 6, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4602445/3169)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
protected vrf:
local ident (addr/mask/prot/port): (10.1.0.0/255.255.0.0/0/0)
remote ident (addr/mask/prot/port): (10.2.0.0/255.255.0.0/0/0)
current_peer: 10.100.2.102:500
PERMIT, flags={}
#pkts encaps: 19, #pkts encrypt: 19, #pkts digest 19
#pkts decaps: 19, #pkts decrypt: 19, #pkts verify 19
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.48.67.181, remote crypto endpt.: 10.100.2.102
path mtu 1500, ip mtu 1500
current outbound spi: 5FBE5408
inbound esp sas:
spi: 0x9CD7288C(2631346316)
transform: esp-3des esp-sha-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2002, flow_id: 3, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4569060/2071)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x5FBE5408(1606308872)
transform: esp-3des esp-sha-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2003, flow_id: 4, crypto map: mymap
sa timing: remaining key lifetime (k/sec): (4569060/2070)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
Dit debug output is verzameld op de hub router, wanneer de spaak router IKE en IPsec SAs initieert.
ISAKMP (0:0): received packet from 10.100.2.102 dport 500 sport 500
Global (N) NEW SA
ISAKMP: local port 500, remote port 500
ISAKMP: insert sa successfully sa = 63D5BE0C
ISAKMP (0:1): Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
ISAKMP (0:1): Old State = IKE_READY New State = IKE_R_MM1
ISAKMP (0:1): processing SA payload. message ID = 0
ISAKMP: Looking for a matching key for 10.100.2.102 in default
ISAKMP: Looking for a matching key for 10.100.2.102 in spokes : success
ISAKMP (0:1): found peer pre-shared key matching 10.100.2.102
ISAKMP (0:1) local preshared key found
ISAKMP : Scanning profiles for xauth ... L2L VPNclient
ISAKMP (0:1) Authentication by xauth preshared
ISAKMP (0:1): Checking ISAKMP transform 1 against priority 10 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0:1): atts are acceptable. Next payload is 0
CryptoEngine0: generate alg parameter
CRYPTO_ENGINE: Dh phase 1 status: 0
CRYPTO_ENGINE: Dh phase 1 status: 0
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP (0:1): Old State = IKE_R_MM1 New State = IKE_R_MM1
ISAKMP (0:1): sending packet to 10.100.2.102 my_port 500 peer_port
500 (R) MM_SA_SETUP
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
ISAKMP (0:1): Old State = IKE_R_MM1 New State = IKE_R_MM2
ISAKMP (0:1): received packet from 10.100.2.102 dport 500 sport 500
Global (R) MM_SA_SETUP
ISAKMP (0:1): Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
ISAKMP (0:1): Old State = IKE_R_MM2 New State = IKE_R_MM3
ISAKMP (0:1): processing KE payload. message ID = 0
CryptoEngine0: generate alg parameter
ISAKMP (0:1): processing NONCE payload. message ID = 0
ISAKMP: Looking for a matching key for 10.100.2.102 in default
ISAKMP: Looking for a matching key for 10.100.2.102 in spokes : success
ISAKMP (0:1): found peer pre-shared key matching 10.100.2.102
CryptoEngine0: create ISAKMP SKEYID for conn id 1
ISAKMP (0:1): SKEYID state generated
ISAKMP (0:1): processing vendor id payload
ISAKMP (0:1): speaking to another IOS box!
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP (0:1): Old State = IKE_R_MM3 New State = IKE_R_MM3
ISAKMP (0:1): sending packet to 10.100.2.102 my_port 500 peer_port 500
(R) MM_KEY_EXCH
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
ISAKMP (0:1): Old State = IKE_R_MM3 New State = IKE_R_MM4
ISAKMP (0:1): received packet from 10.100.2.102 dport 500 sport 500
Global (R) MM_KEY_EXCH
ISAKMP (0:1): Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
ISAKMP (0:1): Old State = IKE_R_MM4 New State = IKE_R_MM5
ISAKMP (0:1): processing ID payload. message ID = 0
ISAKMP (0:1): ID payload
next-payload : 8
type : 1
address : 10.100.2.102
protocol : 17
port : 500
length : 12
ISAKMP (0:1): peer matches L2L profile
ISAKMP: Looking for a matching key for 10.100.2.102 in default
ISAKMP: Looking for a matching key for 10.100.2.102 in spokes : success
ISAKMP (0:1): Found ADDRESS key in keyring spokes
ISAKMP (0:1): processing HASH payload. message ID = 0
CryptoEngine0: generate hmac context for conn id 1
ISAKMP (0:1): SA authentication status: authenticated
ISAKMP (0:1): SA has been authenticated with 10.100.2.102
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP (0:1): Old State = IKE_R_MM5 New State = IKE_R_MM5
ISAKMP (0:1): SA is doing pre-shared key authentication using id type ID_IPV4_ADDR
ISAKMP (0:1): ID payload
next-payload : 8
type : 1
address : 10.48.67.181
protocol : 17
port : 500
length : 12
ISAKMP (1): Total payload length: 12
CryptoEngine0: generate hmac context for conn id 1
CryptoEngine0: clear dh number for conn id 1
ISAKMP (0:1): sending packet to 10.100.2.102 my_port 500 peer_port 500
(R) MM_KEY_EXCH
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
ISAKMP (0:1): Old State = IKE_R_MM5 New State = IKE_P1_COMPLETE
ISAKMP (0:1): Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
ISAKMP (0:1): Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
!--- IKE phase 1 is complete.
ISAKMP (0:1): received packet from 10.100.2.102 dport 500 sport 500 Global
(R) QM_IDLE
ISAKMP: set new node 904613356 to QM_IDLE
CryptoEngine0: generate hmac context for conn id 1
ISAKMP (0:1): processing HASH payload. message ID = 904613356
ISAKMP (0:1): processing SA payload. message ID = 904613356
ISAKMP (0:1): Checking IPSec proposal 1
ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1 (Tunnel)
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 3600
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-SHA
CryptoEngine0: validate proposal
ISAKMP (0:1): atts are acceptable.
IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.48.67.181, remote= 10.100.2.102,
local_proxy= 10.1.0.0/255.255.0.0/0/0 (type=4),
remote_proxy= 10.2.0.0/255.255.0.0/0/0 (type=4),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
CryptoEngine0: validate proposal request
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
ISAKMP (0:1): processing NONCE payload. message ID = 904613356
ISAKMP (0:1): processing ID payload. message ID = 904613356
ISAKMP (0:1): processing ID payload. message ID = 904613356
ISAKMP (0:1): asking for 1 spis from ipsec
ISAKMP (0:1): Node 904613356, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
ISAKMP (0:1): Old State = IKE_QM_READY New State = IKE_QM_SPI_STARVE
IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 4172528328 for SA from 10.48.67.181 to
10.100.2.102 for prot 3
ISAKMP: received ke message (2/1)
CryptoEngine0: generate hmac context for conn id 1
ISAKMP (0:1): sending packet to 10.100.2.102 my_port 500 peer_port 500 (R) QM_IDLE
ISAKMP (0:1): Node 904613356, Input = IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
ISAKMP (0:1): Old State = IKE_QM_SPI_STARVE New State = IKE_QM_R_QM2
ISAKMP (0:1): received packet from 10.100.2.102 dport 500 sport 500 Global
(R) QM_IDLE
CryptoEngine0: generate hmac context for conn id 1
CryptoEngine0: ipsec allocate flow
CryptoEngine0: ipsec allocate flow
ISAKMP (0:1): Creating IPSec SAs
inbound SA from 10.100.2.102 to 10.48.67.181 (f/i) 0/ 0
(proxy 10.2.0.0 to 10.1.0.0)
has spi 0xF8B3BAC8 and conn_id 2000 and flags 2
lifetime of 3600 seconds
lifetime of 4608000 kilobytes
has client flags 0x0
outbound SA from 10.48.67.181 to 10.100.2.102 (f/i) 0/ 0
(proxy 10.1.0.0 to 10.2.0.0 )
has spi 1757151497 and conn_id 2001 and flags A
lifetime of 3600 seconds
lifetime of 4608000 kilobytes
has client flags 0x0
ISAKMP (0:1): deleting node 904613356 error FALSE reason "quick mode done (await)"
ISAKMP (0:1): Node 904613356, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
ISAKMP (0:1): Old State = IKE_QM_R_QM2 New State = IKE_QM_PHASE2_COMPLETE
IPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) INBOUND local= 10.48.67.181, remote= 10.100.2.102,
local_proxy= 10.1.0.0/255.255.0.0/0/0 (type=4),
remote_proxy= 10.2.0.0/255.255.0.0/0/0 (type=4),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 3600s and 4608000kb,
spi= 0xF8B3BAC8(4172528328), conn_id= 2000, keysize= 0, flags= 0x2
IPSEC(initialize_sas): ,
(key eng. msg.) OUTBOUND local= 10.48.67.181, remote= 10.100.2.102,
local_proxy= 10.1.0.0/255.255.0.0/0/0 (type=4),
remote_proxy= 10.2.0.0/255.255.0.0/0/0 (type=4),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 3600s and 4608000kb,
spi= 0x68BC0109(1757151497), conn_id= 2001, keysize= 0, flags= 0xA
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(add mtree): src 10.1.0.0, dest 10.2.0.0, dest_port 0
IPSEC(create_sa): sa created,
(sa) sa_dest= 10.48.67.181, sa_prot= 50,
sa_spi= 0xF8B3BAC8(4172528328),
sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 2000
IPSEC(create_sa): sa created,
(sa) sa_dest= 10.100.2.102, sa_prot= 50,
sa_spi= 0x68BC0109(1757151497),
sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 2001
Deze debug-uitvoer is verzameld op de hubrouter, wanneer de VPN-client IKE en IPsec SA’s initieert.
ISAKMP (0:0): received packet from 10.51.82.100 dport 500 sport 500 Global
(N) NEW SA
ISAKMP: local port 500, remote port 500
ISAKMP: insert sa successfully sa = 63D3D804
ISAKMP (0:2): processing SA payload. message ID = 0
ISAKMP (0:2): processing ID payload. message ID = 0
ISAKMP (0:2): ID payload
next-payload : 13
type : 11
group id : testgroup
protocol : 17
port : 500
length : 17
ISAKMP (0:2): peer matches VPNclient profile
ISAKMP: Looking for a matching key for 10.51.82.100 in default
ISAKMP: Looking for a matching key for 10.51.82.100 in spokes : success
ISAKMP: Created a peer struct for 10.51.82.100, peer port 500
ISAKMP: Locking peer struct 0x644AFC7C, IKE refcount 1 for
crypto_ikmp_config_initialize_sa
ISAKMP (0:2): Setting client config settings 644AFCF8
ISAKMP (0:2): (Re)Setting client xauth list and state
ISAKMP (0:2): processing vendor id payload
ISAKMP (0:2): vendor ID seems Unity/DPD but major 215 mismatch
ISAKMP (0:2): vendor ID is Xauth
ISAKMP (0:2): processing vendor id payload
ISAKMP (0:2): vendor ID is DPD
ISAKMP (0:2): processing vendor id payload
ISAKMP (0:2): vendor ID seems Unity/DPD but major 123 mismatch
ISAKMP (0:2): vendor ID is NAT-T v2
ISAKMP (0:2): processing vendor id payload
ISAKMP (0:2): vendor ID seems Unity/DPD but major 194 mismatch
ISAKMP (0:2): processing vendor id payload
ISAKMP (0:2): vendor ID is Unity
ISAKMP (0:2) Authentication by xauth preshared
!--- Check of ISAKMP transforms against the configured ISAKMP policy.
ISAKMP (0:2): Checking ISAKMP transform 9 against priority 10 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: auth XAUTHInitPreShared
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
ISAKMP (0:2): atts are acceptable. Next payload is 3
CryptoEngine0: generate alg parameter
CRYPTO_ENGINE: Dh phase 1 status: 0
CRYPTO_ENGINE: Dh phase 1 status: 0
ISAKMP (0:2): processing KE payload. message ID = 0
CryptoEngine0: generate alg parameter
ISAKMP (0:2): processing NONCE payload. message ID = 0
ISAKMP (0:2): vendor ID is NAT-T v2
ISAKMP (0:2): Input = IKE_MESG_FROM_PEER, IKE_AM_EXCH
ISAKMP (0:2): Old State = IKE_READY New State = IKE_R_AM_AAA_AWAIT
ISAKMP: got callback 1
CryptoEngine0: create ISAKMP SKEYID for conn id 2
ISAKMP (0:2): SKEYID state generated
ISAKMP (0:2): constructed NAT-T vendor-02 ID
ISAKMP (0:2): SA is doing pre-shared key authentication plus XAUTH
using id type ID_IPV4_ADDR
ISAKMP (0:2): ID payload
next-payload : 10
type : 1
address : 10.48.67.181
protocol : 17
port : 0
length : 12
ISAKMP (2): Total payload length: 12
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port 500
(R) AG_INIT_EXCH
ISAKMP (0:2): Input = IKE_MESG_FROM_AAA, PRESHARED_KEY_REPLY
ISAKMP (0:2): Old State = IKE_R_AM_AAA_AWAIT New State = IKE_R_AM2
ISAKMP (0:2): received packet from 10.51.82.100 dport 500 sport 500 Global
(R) AG_INIT_EXCH
ISAKMP (0:2): processing HASH payload. message ID = 0
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): processing NOTIFY INITIAL_CONTACT protocol 1
spi 0, message ID = 0, sa = 63D3D804
ISAKMP (0:2): SA authentication status: authenticated
ISAKMP (0:2): Process initial contact,
bring down existing phase 1 and 2 SA's with local 10.48.67.181 remote
10.51.82.100 remote port 500
ISAKMP (0:2): returning IP addr to the address pool
IPSEC(key_engine): got a queue event...
ISAKMP:received payload type 17
ISAKMP:received payload type 17
ISAKMP (0:2): SA authentication status: authenticated
ISAKMP (0:2): SA has been authenticated with 10.51.82.100
CryptoEngine0: clear dh number for conn id 1
ISAKMP: Trying to insert a peer 10.48.67.181/10.51.82.100/500/,
and inserted successfully.
ISAKMP: set new node 1257790711 to CONF_XAUTH
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port 500 (R) QM_IDLE
ISAKMP (0:2): purging node 1257790711
ISAKMP: Sending phase 1 responder lifetime 86400
ISAKMP (0:2): Input = IKE_MESG_FROM_PEER, IKE_AM_EXCH
ISAKMP (0:2): Old State = IKE_R_AM2 New State = IKE_P1_COMPLETE
ISAKMP (0:2): Need XAUTH
ISAKMP (0:2): Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
ISAKMP (0:2): Old State = IKE_P1_COMPLETE New State = IKE_XAUTH_AAA_START_LOGIN_AWAIT
ISAKMP: got callback 1
ISAKMP: set new node 955647754 to CONF_XAUTH
!--- Extended authentication begins.
ISAKMP/xauth: request attribute XAUTH_USER_NAME_V2
ISAKMP/xauth: request attribute XAUTH_USER_PASSWORD_V2
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): initiating peer config to 10.51.82.100. ID = 955647754
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port 500
(R) CONF_XAUTH
ISAKMP (0:2): Input = IKE_MESG_FROM_AAA, IKE_AAA_START_LOGIN
ISAKMP (0:2): Old State = IKE_XAUTH_AAA_START_LOGIN_AWAIT New State =
IKE_XAUTH_REQ_SENT
ISAKMP (0:2): received packet from 10.51.82.100 dport 500 sport 500 Global
(R) CONF_XAUTH
ISAKMP (0:2): processing transaction payload from 10.51.82.100. message
ID = 955647754
CryptoEngine0: generate hmac context for conn id 2
ISAKMP: Config payload REPLY
!--- Username/password received from the VPN Client.
ISAKMP/xauth: reply attribute XAUTH_USER_NAME_V2
ISAKMP/xauth: reply attribute XAUTH_USER_PASSWORD_V2
ISAKMP (0:2): deleting node 955647754 error FALSE reason "done with
xauth request/reply exchange"
ISAKMP (0:2): Input = IKE_MESG_FROM_PEER, IKE_CFG_REPLY
ISAKMP (0:2): Old State = IKE_XAUTH_REQ_SENT New State =
IKE_XAUTH_AAA_CONT_LOGIN_AWAIT
ISAKMP: got callback 1
ISAKMP: set new node -1118110738 to CONF_XAUTH
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): initiating peer config to 10.51.82.100. ID = -1118110738
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port
500 (R) CONF_XAUTH
ISAKMP (0:2): Input = IKE_MESG_FROM_AAA, IKE_AAA_CONT_LOGIN
ISAKMP (0:2): Old State = IKE_XAUTH_AAA_CONT_LOGIN_AWAIT New State =
IKE_XAUTH_SET_SENT
ISAKMP (0:2): received packet from 10.51.82.100 dport 500 sport 500 Global
(R) CONF_XAUTH
ISAKMP (0:2): processing transaction payload from 10.51.82.100. message
ID = -1118110738
CryptoEngine0: generate hmac context for conn id 2
!--- Success
ISAKMP: Config payload ACK
ISAKMP (0:2): XAUTH ACK Processed
ISAKMP (0:2): deleting node -1118110738 error FALSE reason "done with transaction"
ISAKMP (0:2): Input = IKE_MESG_FROM_PEER, IKE_CFG_ACK
ISAKMP (0:2): Old State = IKE_XAUTH_SET_SENT New State = IKE_P1_COMPLETE
ISAKMP (0:2): Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
ISAKMP (0:2): Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
ISAKMP (0:2): received packet from 10.51.82.100 dport 500 sport 500
Global (R) QM_IDLE
ISAKMP: set new node -798495444 to QM_IDLE
ISAKMP (0:2): processing transaction payload from 10.51.82.100. message
ID = -798495444
CryptoEngine0: generate hmac context for conn id 2
ISAKMP: Config payload REQUEST
ISAKMP (0:2): checking request:
ISAKMP: IP4_ADDRESS
ISAKMP: IP4_NETMASK
ISAKMP: IP4_DNS
ISAKMP: IP4_NBNS
ISAKMP: ADDRESS_EXPIRY
ISAKMP: UNKNOWN Unknown Attr: 0x7000
ISAKMP: UNKNOWN Unknown Attr: 0x7001
ISAKMP: DEFAULT_DOMAIN
ISAKMP: SPLIT_INCLUDE
ISAKMP: UNKNOWN Unknown Attr: 0x7003
ISAKMP: UNKNOWN Unknown Attr: 0x7007
ISAKMP: UNKNOWN Unknown Attr: 0x7009
ISAKMP: APPLICATION_VERSION
ISAKMP: UNKNOWN Unknown Attr: 0x7008
ISAKMP: UNKNOWN Unknown Attr: 0x700A
ISAKMP: UNKNOWN Unknown Attr: 0x7005
ISAKMP (0:2): Input = IKE_MESG_FROM_PEER, IKE_CFG_REQUEST
ISAKMP (0:2): Old State = IKE_P1_COMPLETE New State = IKE_CONFIG_AUTHOR_AAA_AWAIT
ISAKMP: got callback 1
ISAKMP (0:2): attributes sent in message:
Address: 0.2.0.0
ISAKMP (0:2): allocating address 10.5.5.1
ISAKMP: Sending private address: 10.5.5.1
ISAKMP: Sending IP4_DNS server address: 1.1.1.1
ISAKMP: Sending IP4_DNS server address: 2.2.2.2
ISAKMP: Sending IP4_NBNS server address: 3.3.3.3
ISAKMP: Sending IP4_NBNS server address: 4.4.4.4
ISAKMP: Sending ADDRESS_EXPIRY seconds left to use the address: 86386
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7000)
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7001)
ISAKMP: Sending DEFAULT_DOMAIN default domain name: cisco.com
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7003)
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7007)
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7009)
ISAKMP: Sending APPLICATION_VERSION string: Cisco Internetwork Operating
System Software
IOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(6a), RELEASE SOFTWARE (fc4)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 02-Apr-04 15:52 by kellythw
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7008)
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x700A)
ISAKMP (0/2): Unknown Attr: UNKNOWN (0x7005)
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): responding to peer config from 10.51.82.100. ID = -798495444
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port 500 (R) CONF_ADDR
ISAKMP (0:2): deleting node -798495444 error FALSE reason ""
ISAKMP (0:2): Input = IKE_MESG_FROM_AAA, IKE_AAA_GROUP_ATTR
ISAKMP (0:2): Old State = IKE_CONFIG_AUTHOR_AAA_AWAIT New State = IKE_P1_COMPLETE
ISAKMP (0:2): Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
ISAKMP (0:2): Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
!--- IKE phase 1 and Config Mode complete. !--- Check of IPsec proposals against configured transform set(s).
ISAKMP (0:2): Checking IPSec proposal 12
ISAKMP: transform 1, ESP_3DES
ISAKMP: attributes in transform:
ISAKMP: authenticator is HMAC-SHA
ISAKMP: encaps is 1 (Tunnel)
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (VPI) of 0x0 0x20 0xC4 0x9B
CryptoEngine0: validate proposal
ISAKMP (0:2): atts are acceptable.
IPSEC(validate_proposal_request): proposal part #1,
(key eng. msg.) INBOUND local= 10.48.67.181, remote= 10.51.82.100,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.5.5.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x2
CryptoEngine0: validate proposal request
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
ISAKMP (0:2): processing NONCE payload. message ID = 381726614
ISAKMP (0:2): processing ID payload. message ID = 381726614
ISAKMP (0:2): processing ID payload. message ID = 381726614
ISAKMP (0:2): asking for 1 spis from ipsec
ISAKMP (0:2): Node 381726614, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
ISAKMP (0:2): Old State = IKE_QM_READY New State = IKE_QM_SPI_STARVE
IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 2048571635 for SA
from 10.48.67.181 to 10.51.82.100 for prot 3
ISAKMP: received ke message (2/1)
CryptoEngine0: generate hmac context for conn id 2
ISAKMP (0:2): sending packet to 10.51.82.100 my_port 500 peer_port 500 (R) QM_IDLE
ISAKMP (0:2): Node 381726614, Input = IKE_MESG_FROM_IPSEC, IKE_SPI_REPLY
ISAKMP (0:2): Old State = IKE_QM_SPI_STARVE New State = IKE_QM_R_QM2
ISAKMP (0:2): received packet from 10.51.82.100 dport 500 sport 500 Global
(R) QM_IDLE
CryptoEngine0: generate hmac context for conn id 2
CryptoEngine0: ipsec allocate flow
CryptoEngine0: ipsec allocate flow
ISAKMP: Locking peer struct 0x644AFC7C, IPSEC refcount 1 for for stuff_ke
ISAKMP (0:2): Creating IPSec SAs
inbound SA from 10.51.82.100 to 10.48.67.181 (f/i) 0/ 0
(proxy 10.5.5.1 to 0.0.0.0)
has spi 0x7A1AB8F3 and conn_id 2004 and flags 2
lifetime of 2147483 seconds
has client flags 0x0
outbound SA from 10.48.67.181 to 10.51.82.100 (f/i) 0/ 0 (proxy 0.0.0.0 to 10.5.5.1 )
has spi -1329531732 and conn_id 2005 and flags A
lifetime of 2147483 seconds
has client flags 0x0
ISAKMP (0:2): deleting node 381726614 error FALSE reason "quick mode done (await)"
ISAKMP (0:2): Node 381726614, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
ISAKMP (0:2): Old State = IKE_QM_R_QM2 New State = IKE_QM_PHASE2_COMPLETE
IPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) INBOUND local= 10.48.67.181, remote= 10.51.82.100,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.5.5.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 2147483s and 0kb,
spi= 0x7A1AB8F3(2048571635), conn_id= 2004, keysize= 0, flags= 0x2
IPSEC(initialize_sas): ,
(key eng. msg.) OUTBOUND local= 10.48.67.181, remote= 10.51.82.100,
local_proxy= 0.0.0.0/0.0.0.0/0/0 (type=4),
remote_proxy= 10.5.5.1/0.0.0.0/0/0 (type=1),
protocol= ESP, transform= esp-3des esp-sha-hmac (Tunnel),
lifedur= 2147483s and 0kb,
spi= 0xB0C0F4AC(2965435564), conn_id= 2005, keysize= 0, flags= 0xA
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(kei_proxy): head = mymap, map->ivrf = , kei->ivrf =
IPSEC(add mtree): src 0.0.0.0, dest 10.5.5.1, dest_port 0
IPSEC(create_sa): sa created,
(sa) sa_dest= 10.48.67.181, sa_prot= 50,
sa_spi= 0x7A1AB8F3(2048571635),
sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 2004
IPSEC(create_sa): sa created,
(sa) sa_dest= 10.51.82.100, sa_prot= 50,
sa_spi= 0xB0C0F4AC(2965435564),
sa_trans= esp-3des esp-sha-hmac , sa_conn_id= 2005
Controleer de volgnummers van cryptokaarten
Als statische en dynamische peers op dezelfde crypto map zijn geconfigureerd, is de volgorde van de crypto map-vermeldingen zeer belangrijk. Het volgnummer van de dynamische crypto map-vermelding moet hoger zijn dan alle andere statische crypto map-vermeldingen. Als de statische waarden hoger zijn genummerd dan de dynamische waarden, mislukken de verbindingen met deze peers.
Dit is een voorbeeld van een goed genummerde crypto map die een statische en een dynamische vermelding bevat. Merk op dat de dynamische ingang het hoogste volgnummer heeft, en er ruimte is overgelaten voor aanvullende statische vermeldingen:
crypto dynamic-map dynmap 20 set transform-set myset crypto map mymap 10 ipsec-isakmp match address 100 set peer 172.16.77.10 set transform-set myset crypto map mymap 60000 ipsec-isakmp dynamic dynmap
Problemen oplossen
Er is momenteel geen specifieke troubleshooting-informatie beschikbaar voor deze configuratie.
Gerelateerde informatie
Revisiegeschiedenis
| Revisie | Publicatiedatum | Opmerkingen |
|---|---|---|
1.0 |
28-Oct-2003
|
Eerste vrijgave |
Feedback