Dynamisch multipoint VPN configureren met GRE over IPsec met OSPF, NAT en Cisco IOS-firewall
Inhoud
Inleiding
Dit document biedt een voorbeeldconfiguratie voor Dynamic Multipoint VPN (DMVPN) door generieke Routing Encapsulation (GRE) via IPsec met Open Shortest Path First (OSPF), Network adresomzetting (NAT) en Cisco IOS® Firewall.
Voorwaarden
Vereisten
Voordat een GRE-tunnel (mGRE) met meerdere punten en IPsec kan worden gerealiseerd, moet u een IKE-beleid (Internet Key Exchange) definiëren via de opdracht crypto Sakmp-beleid.
Opmerking: Gebruik het Opname Gereedschap (alleen geregistreerde klanten) om meer informatie te verkrijgen over de opdrachten die in deze sectie worden gebruikt.
Gebruikte componenten
De informatie in dit document is gebaseerd op de volgende software- en hardware-versies:
-
Cisco IOS® softwarerelease 12.2(15)T1 op de router en Cisco IOS-softwarerelease 12.3(1.6)op de gemaakte routers
-
Cisco 3620 als hubrouter, twee Cisco 1720 routers en één Cisco 3620 router zoals spraakrouters
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u de potentiële impact van elke opdracht begrijpen.
Conventies
Raadpleeg de Cisco Technical Tips Convention voor meer informatie over documentconventies.
Configureren
Deze sectie bevat informatie over het configureren van de functies die in dit document worden beschreven.
Opmerking: Gebruik het Opname Gereedschap (alleen geregistreerde klanten) om meer informatie te verkrijgen over de opdrachten die in deze sectie worden gebruikt.
Netwerkdiagram
Dit document maakt gebruik van deze netwerkinstellingen.
Configuraties
Dit document gebruikt deze configuraties.
| Hub 3620-B |
|---|
W2N-6.16-3620-B#write terminal Building configuration... Current configuration : 2613 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname W2N-6.16-3620-B ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the Cisco IOS Firewall configuration and what to inspect. !--- This is applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out ftp ip inspect name in2out tftp ip inspect name in2out tcp timeout 43200 ip inspect name in2out http ip inspect name in2out udp ip audit po max-events 100 ! ! ! !--- Create an Internet Security Association and Key Management !--- Protocol (ISAKMP) policy for Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 crypto isakmp nat keepalive 20 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPsec profile to be applied dynamically !--- to the GRE over IPsec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! !--- This is the inbound interface. interface Loopback1 ip address 192.168.117.1 255.255.255.0 ip nat inside ! !--- Create a GRE tunnel template to be applied !--- to all the dynamically created GRE tunnels. interface Tunnel1 description MULTI-POINT GRE TUNNEL for BRANCHES bandwidth 1000 ip address 172.16.0.1 255.255.255.0 no ip redirects ip mtu 1416 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp network-id 99 ip nhrp holdtime 300 no ip route-cache ip ospf network broadcast no ip mroute-cache delay 1000 tunnel source FastEthernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outbound interface. interface FastEthernet0/0 ip address 14.24.117.1 255.255.0.0 ip nat outside ip access-group 100 in ip inspect in2out out no ip mroute-cache duplex auto speed auto ! interface Serial0/0 no ip address shutdown clockrate 2000000 no fair-queue ! interface FastEthernet0/1 no ip address no ip mroute-cache duplex auto speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router ospf 1 log-adjacency-changes network 172.16.0.0 0.0.0.255 area 0 network 192.168.117.0 0.0.0.255 area 0 ! !--- Except the private network traffic from the NAT process. ip nat inside source route-map nonat interface FastEthernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 2.0.0.0 255.0.0.0 14.24.121.1 ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- Cisco IOS Firewall opens other inbound access as needed. access-list 100 permit udp any host 14.24.117.1 eq 500 access-list 100 premit esp any host 14.24.117.1 access-list 100 permit gre any host 14.24.117.1 access-list 100 deny ip any any !--- Except the private network traffic from the NAT process. access-list 110 deny ip 192.168.117.0 0.0.0.255 192.168.118.0 0.0.0.255 access-list 110 deny ip 192.168.117.0 0.0.0.255 192.168.116.0 0.0.0.255 access-list 110 deny ip 192.168.117.0 0.0.0.255 192.168.120.0 0.0.0.255 access-list 110 permit ip 192.168.117.0 0.0.0.255 any ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end W2N-6.16-3620-B# |
| Spoke 1 - 3620-A |
|---|
W2N-6.16-3620-A#write terminal Building configuration... Current configuration : 2678 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname W2N-6.16-3620-A ! boot system flash slot0:c3620-ik9o3s7-mz.122-15.T1.bin logging queue-limit 100 ! memory-size iomem 15 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the Cisco IOS Firewall configuration and what to inspect. !--- This is applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPsec profile to be applied dynamically !--- to the GRE over IPsec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! ! !--- This is the inbound interface. interface Loopback1 ip address 192.168.118.1 255.255.255.0 ip nat inside ! !--- Create a GRE tunnel template to be applied to !--- all the dynamically created GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.2 255.255.255.0 no ip redirects ip mtu 1416 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip route-cache ip ospf network broadcast no ip mroute-cache delay 1000 tunnel source Ethernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outbound interface. interface Ethernet0/0 ip address 14.24.118.1 255.255.0.0 ip nat outside ip access-group 100 in ip inspect in2out out no ip mroute-cache half-duplex ! interface Ethernet0/1 no ip address half-duplex ! interface Ethernet0/2 no ip address shutdown half-duplex ! interface Ethernet0/3 no ip address shutdown half-duplex ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router ospf 1 log-adjacency-changes redistribute connected network 172.16.0.0 0.0.0.255 area 0 network 192.168.118.0 0.0.0.255 area 0 ! !--- Except the private network traffic from the NAT process. ip nat inside source route-map nonat interface Ethernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 2.0.0.0 255.0.0.0 14.24.121.1 ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- Cisco IOS Firewall opens inbound access as needed. access-list 100 permit udp any host 14.24.118.1 eq 500 access-list 100 premit esp any host 14.24.118.1 access-list 100 permit gre any host 14.24.118.1 access-list 100 deny ip any any !--- Except the private network traffic from the NAT process. access-list 110 deny ip 192.168.118.0 0.0.0.255 192.168.117.0 0.0.0.255 access-list 110 deny ip 192.168.118.0 0.0.0.255 192.168.116.0 0.0.0.255 access-list 110 deny ip 192.168.118.0 0.0.0.255 192.168.120.0 0.0.0.255 access-list 110 permit ip 192.168.118.0 0.0.0.255 any ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end W2N-6.16-3620-A# |
| Spoke 2 - 1720-b |
|---|
1720-b#write terminal Building configuration... Current configuration : 2623 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 1720-b ! logging queue-limit 100 enable password cisco ! username 7206-B password 0 cisco ip subnet-zero ! ! no ip domain lookup ! ip cef !--- This is the Cisco IOS Firewall configuration and what to inspect. !--- This is applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 vpdn-group 1 request-dialin protocol pppoe ! ! ! ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPsec profile to be applied dynamically !--- to the GRE over IPsec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! ! ! ! !--- This is the inbound interface. interface Loopback1 ip address 192.168.116.1 255.255.255.0 ip nat inside ! !--- Create a GRE tunnel template to be applied to !--- all the dynamically created GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.3 255.255.255.0 no ip redirects ip mtu 1416 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip route-cache ip ospf network broadcast no ip mroute-cache delay 1000 tunnel source Dialer1 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address half-duplex ! interface FastEthernet0 no ip address no ip mroute-cache speed auto pppoe enable pppoe-client dial-pool-number 1 ! !--- This is the outbound interface. interface Dialer1 ip address 2.2.2.10 255.255.255.0 ip inspect in2out out ip access-group 100 in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication pap chap callin ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router ospf 1 log-adjacency-changes redistribute connected network 172.16.0.0 0.0.0.255 area 0 network 192.168.116.0 0.0.0.255 area 0 ! !--- Except the private network traffic from the NAT process. ip nat inside source route-map nonat interface Dialer1 overload ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- Cisco IOS Firewall opens inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 premit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any !--- Except the private network traffic from the NAT process. access-list 110 deny ip 192.168.116.0 0.0.0.255 192.168.117.0 0.0.0.255 access-list 110 deny ip 192.168.116.0 0.0.0.255 192.168.118.0 0.0.0.255 access-list 110 deny ip 192.168.116.0 0.0.0.255 192.168.120.0 0.0.0.255 access-list 110 permit ip 192.168.116.0 0.0.0.255 any dialer-list 1 protocol ip permit ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! no scheduler allocate end 1720-b# |
| Spoke 3 - 1720-A |
|---|
W2N-6.16-1720-A#write terminal Building configuration... Current configuration : 2303 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname W2N-6.16-1720-A ! logging queue-limit 100 ! memory-size iomem 25 ip subnet-zero ! ! no ip domain lookup ! ip cef !--- This is the Cisco IOS Firewall configuration and what to inspect. !--- This is applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit notify log ip audit po max-events 100 ! ! ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPsec profile to be applied dynamically !--- to the GRE over IPsec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! ! ! ! !--- This is the inbound interface. interface Loopback1 ip address 192.168.120.1 255.255.255.0 ip nat inside ! !--- Create a GRE tunnel template to be applied to !--- all the dynamically created GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.4 255.255.255.0 no ip redirects ip mtu 1416 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 ip ospf network broadcast no ip mroute-cache delay 1000 tunnel source FastEthernet0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address no ip mroute-cache half-duplex ! !--- This is the outbound interface. interface FastEthernet0 ip address 14.24.120.1 255.255.0.0 ip nat outside ip inspect in2out out ip access-group 100 in no ip mroute-cache speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router ospf 1 log-adjacency-changes redistribute connected network 172.16.0.0 0.0.0.255 area 0 network 192.168.120.0 0.0.0.255 area 0 ! !--- Except the private network traffic from the NAT process. ip nat inside source route-map nonat interface FastEthernet0 overload ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 2.0.0.0 255.0.0.0 14.24.121.1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- Cisco IOS Firewall opens inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 premit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.120.0 0.0.0.255 any !--- Except the private network traffic from the NAT process. access-list 110 deny ip 192.168.120.0 0.0.0.255 192.168.116.0 0.0.0.255 access-list 110 deny ip 192.168.120.0 0.0.0.255 192.168.117.0 0.0.0.255 access-list 110 deny ip 192.168.120.0 0.0.0.255 192.168.118.0 0.0.0.255 access-list 110 permit ip 192.168.120.0 0.0.0.255 any ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! end W2N-6.16-1720-A# |
Verifiëren
Gebruik dit gedeelte om te bevestigen dat de configuratie correct werkt.
Het Uitvoer Tolk (uitsluitend geregistreerde klanten) (OIT) ondersteunt bepaalde show opdrachten. Gebruik de OIT om een analyse van tonen opdrachtoutput te bekijken.
-
toon crypto isakmp sa-Toont de staat voor de ISAKMP security association (SA).
-
Laat actieve encryptie-motorverbindingen zien - Hiermee geeft u de totale versleuteling/decrypts per SA weer.
-
Laat crypto ipsec sa-displays de statistieken op de actieve tunnels zien.
-
toon ip route-Toont de routingtabel.
-
Toon ip ospf buurman-Beeldinformatie OSPF buurinformatie op een per-interface basis.
-
toon ip Nhrp-Toont het IP Next Hop Resolutie Protocol (NHRP) cache, optioneel beperkt tot dynamische of statische cache items voor een specifieke interface.
Problemen oplossen
Deze sectie bevat informatie waarmee u problemen met de configuratie kunt oplossen.
Opdrachten voor troubleshooting
Opmerking: Raadpleeg Belangrijke informatie over debug Commands voordat u debug-opdrachten afgeeft.
-
debug van crypto ipsec-displays IPsec gebeurtenissen.
-
debug van crypto isakmp-displays over IKE gebeurtenissen.
-
debug van crypto motor—informatie van de crypto motor.
Aanvullende informatie over het opsporen en verhelpen van IPsec kan worden gevonden bij IP Security Troubleshooter - Beginnen en Werken met debug-opdrachten.
Feedback