De documentatie van dit product is waar mogelijk geschreven met inclusief taalgebruik. Inclusief taalgebruik wordt in deze documentatie gedefinieerd als taal die geen discriminatie op basis van leeftijd, handicap, gender, etniciteit, seksuele oriëntatie, sociaaleconomische status of combinaties hiervan weerspiegelt. In deze documentatie kunnen uitzonderingen voorkomen vanwege bewoordingen die in de gebruikersinterfaces van de productsoftware zijn gecodeerd, die op het taalgebruik in de RFP-documentatie zijn gebaseerd of die worden gebruikt in een product van een externe partij waarnaar wordt verwezen. Lees meer over hoe Cisco gebruikmaakt van inclusief taalgebruik.
Cisco heeft dit document vertaald via een combinatie van machine- en menselijke technologie om onze gebruikers wereldwijd ondersteuningscontent te bieden in hun eigen taal. Houd er rekening mee dat zelfs de beste machinevertaling niet net zo nauwkeurig is als die van een professionele vertaler. Cisco Systems, Inc. is niet aansprakelijk voor de nauwkeurigheid van deze vertalingen en raadt aan altijd het oorspronkelijke Engelstalige document (link) te raadplegen.
Dit document beschrijft hoe u situaties kunt voorkomen waarin de Cisco NCS 560 routeprocessor (RP) niet reageert na een herladen of een stroomcyclus.
In de meeste gevallen worden de NCS 560-implementaties uitgevoerd op afgelegen locaties, in grote aantallen, en waar menselijke interventie tot een minimum moet worden beperkt.
In deze implementaties is het ook belangrijk om te voldoen aan de verplichte SMU-installatievereisten op basis van de geïnstalleerde release.
Opmerking: Vanaf Cisco IOS XR-release 7.2.2 en hoger hoeft u het MKB niet langer afzonderlijk te installeren.
IOS XR versie |
SMU |
Verband |
Opmerkingen |
6.6.3 |
CSCvt69762 |
||
7.0.1 |
CSCvw42910 |
Het is verplicht over te gaan op de uitgebreide onderhoudsrelease (EMR) van dezelfde kleine release. Bijvoorbeeld IOS XR 7.0.2. |
|
7.0.2 |
CSCvt69762 |
||
7.1.1 |
CSCv41516 |
Het is aan te raden om over te gaan op de EMR-afgifte van dezelfde kleine afgifte. Bijvoorbeeld IOS XR 7.1.2. |
|
7.1.2 |
CSCv41516 |
|
|
7.2.1 |
CSCv41516 |
FPD's moeten worden bijgewerkt om ervoor te zorgen dat FPD's altijd een versie hebben die gelijk is aan of hoger is dan de minimaal vereiste versie die voor die Cisco IOS® XR-release is vereist.
ADM |
1.06 |
IOFPGA |
0.64 |
BIOS |
0.16 |
In dit document wordt ervan uitgegaan dat:
de prompt voor verschillende locaties, zodat alle opdrachten om door de verschillende locaties te navigeren, worden weggelaten.
1. XR - RP0
RP/0/RP0/CPU0:ios#
2. XR - RP1
RP/0/RP1/CPU0:ios#
3. sysadmin - RP0
sysadmin-vm:0_RP0#
4. sysadmin - RP1
sysadmin-vm:0_RP1#
5. sysadmin - RP0 shell
[sysadmin-vm:0_RP0:~]$
6. sysadmin - RP1 shell
[sysadmin-vm:0_RP1:~]$
Deze KMO's moeten vóór dit proces actief zijn en zich inzetten voor het systeem.
RP/0/RP0/CPU0:ios#show install active summary
Active Packages: 10
ncs560-xr-7.1.2 version=7.1.2 [Boot image]
ncs560-mcast-2.0.0.0-r712
ncs560-mgbl-2.0.0.0-r712
ncs560-mpls-1.0.0.0-r712
ncs560-mpls-te-rsvp-2.0.0.0-r712
ncs560-ospf-2.0.0.0-r712
ncs560-k9sec-2.1.0.0-r712
ncs560-iosxr-fwding-2.1.0.1-r712.CSCvp67225
ncs560-os-support-2.1.0.1-r712.CSCvv41516
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .xr
sysadmin-vm:0_RP0# show install active summary
Active Packages: 4
ncs560-sysadmin-7.1.2 version=7.1.2 [Boot image]
ncs560-sysadmin-ncs560-7.1.2.1-r712.CSCvv41516
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .admin
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .host
RP/0/RP0/CPU0:ios#show hw-module fpd
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA NEED UPGD 0.53 0.53
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP0 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/RP1 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA NEED UPGD 0.53 0.53
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP1 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
Het is belangrijk ervoor te zorgen dat het TAM-gebied niet wordt gecorrumpeerd; anders kunnen een IOFPGA, FPD-upgrade en daaropvolgende herladingen leiden tot een RMA. Met deze MOP, omdat FPD versie 0.64 of hoger in gebruik is, leidt dit IOFPGA FPD upgrade proces en RP reload tot TAM corruptie herstel.
sysadmin-vm:0_RP0# show control-driver info location 0/RP0
...
Card view from local RP:
TAM Memory is not corrupted
Can proceed with IOFPGA upgrade if required
...
sysadmin-vm:0_RP0# show control-driver info location 0/RP1
...
Card view from local RP:
TAM Memory is not corrupted
Can proceed with IOFPGA upgrade if required
...
Opmerking: Als TAM Memory is beschadigd, is het geen probleem als de beoogde IOFPGA-versie 0,64 of hoger is.
sysadmin-vm:0_RP1# show control-driver info location 0/RP0 <snip> Card view from local RP: TAM Memory is corrupted Do not proceed with IOFPGA upgrade
<snip>
Opmerking: Als aan alle voorwaarden die in dit document worden vermeld, is voldaan, kunt u met de upgrade doorgaan. De "niet verder gaan met de IOFPGA-upgrade" verwijst naar de IOFPGA-versie die eerder is dan 0,64.
RP/0/RP0/CPU0:ios#upgrade hw-module location all fpd IOFPGA
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP0/CPU0:RONALDO-RF2a#0/RP0/ADMIN0:Oct 16 15:19:26.609 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 IOFPGA FALSE
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 IOFPGA FALSE
RP/0/RP0/CPU0:ios#show hw-module fpd
Fri Oct 16 15:22:11.256 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA RLOAD REQ 0.53 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP0 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/RP1 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA RLOAD REQ 0.53 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP1 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
Laad eerst de stand-by RP opnieuw:
sysadmin-vm:0_RP0# hw-module location 0/RP1 reload
Reload hardware module ? [no,yes] yes
Nadat de redundantie is hersteld, herlaadt u de actieve RP (RP0) (dit veroorzaakt een failover):
sysadmin-vm:0_RP0# hw-module location 0/RP0 reload
Reload hardware module ? [no,yes] yes
Op de nieuwe actieve RP (RP1):
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.2
Bootloader Version : 0.0.9
Config Version : 1.4
Op de nieuwe standby RP (RP0):
[sysadmin-vm:0_RP0:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.2
Bootloader Version : 0.0.9
Config Version : 1.4
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPd ADM
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 15:57:14.332 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 ADM FALSE
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 ADM FALSE
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPD PRIMARY-BIOS
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 PRIMARY-BIOS FALSE
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 PRIMARY-BIOS FALSE
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPD SATA
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 SATA FALSE
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 SATA FALSE
RP/0/RP1/CPU0:ios#show hw-module fpd
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM RLOAD REQ 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS RLOAD REQ 0.15 0.16
0/RP0 N560-RSP4-E 0.0 SATA RLOAD REQ 1.30 2.10
0/RP1 N560-RSP4-E 0.0 ADM RLOAD REQ 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS RLOAD REQ 0.15 0.16
0/RP1 N560-RSP4-E 0.0 SATA RLOAD REQ 1.30 2.10
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
Opmerking: Als de versie van de ADM-firmware 1.14.2 is, moet u alle bestandssystemen op alle VM's/host synchroniseren voordat u het reload-script gebruikt.
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.1 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.4 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.4 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.1 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.1 chvrf 0 ssh 10.0.2.2 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.1 chvrf 0 ssh 10.0.2.2 sync
Opmerking: Er is geen uitvoer voor deze opdrachten.
Zo laadt u het chassis opnieuw:
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/reboot_system.sh
Initiating power-cycle of 0/RP0
Initiating power-cycle of 0/RP1
Opmerking: Als de ADM firmware-versie 1.14.3 is, moeten FPD's op de RP opnieuw worden geladen.
Laad eerst de standby RP (RP0) opnieuw:
sysadmin-vm:0_RP1# hw-module location 0/RP0 reload
Reload hardware module ? [no,yes] yes
Nadat de redundantie is hersteld, herlaadt u de actieve RP (RP1) (dit veroorzaakt een failover):
sysadmin-vm:0_RP1# hw-module location 0/RP1 reload
Reload hardware module ? [no,yes] yes
RP/0/RP0/CPU0:ios#show hw-module fpd
Fri Oct 16 16:24:18.849 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM CURRENT 1.06 1.06
0/RP0 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS CURRENT 0.16 0.16
0/RP0 N560-RSP4-E 0.0 SATA CURRENT 2.10 2.10
0/RP1 N560-RSP4-E 0.0 ADM CURRENT 1.06 1.06
0/RP1 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS CURRENT 0.16 0.16
0/RP1 N560-RSP4-E 0.0 SATA CURRENT 2.10 2.10
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
[sysadmin-vm:0_RP0:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.3
Bootloader Version : 0.0.9
Config Version : 1.6
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.3
Bootloader Version : 0.0.9
Config Version : 1.6
RP/0/RP0/CPU0:ios#upgrade hw-module location 0/5 FPD IMFPGA
Fri Oct 16 16:28:15.006 CEST
upgrade command issued (use "show hw-module fpd" to check upgrade status)
Revisie | Publicatiedatum | Opmerkingen |
---|---|---|
2.0 |
10-Nov-2021 |
Eerste vrijgave |
1.0 |
10-Nov-2021 |
Eerste vrijgave |