Upgrade Catalyst 9400 Dual Supervisors naar Cisco IOS® XE v16.6.2
Inhoud
Inleiding
Dit document beschrijft de upgradeprocedure voor Catalyst 9400 Dual Supervisors naar Cisco IOS XE van v16.6.1 naar v16.6.2.
Voorwaarden
Vereisten
Cisco raadt je aan om kennis te hebben van TFTP en FTP.
Gebruikte componenten
De informatie in dit document is gebaseerd op de volgende software- en hardware-versies:
- Hardware: C9410R
- Software: cat9k_iosxe.16.06.01.SPA.bin
In dit voorbeeld is uw huidige afbeelding cat9k_iosxe.16.06.01.SPA.bin en de doelafbeelding is cat9k_iosxe.16.06.02.SPA.bin. Deze procedure werkt ook als u een C9407R-chassis hebt in plaats van een C9410R-chassis.
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u zorgen dat u de potentiële impact van elke opdracht begrijpt.
Automatische opstartladerupgrade en CPLD-upgrade
Automatische upgrade van opstartlader
Wanneer u voor het eerst een upgrade uitvoert van de huidige Cisco IOS® XE-release op uw switch naar een latere of nieuwere release, kan de opstartlader automatisch worden bijgewerkt op basis van de hardwareversie van de switch. Als de opstartlader wordt bijgewerkt, laadt de supervisor automatisch opnieuw om de nieuwe opstartlader in te schakelen. Als u daarna teruggaat naar de oudere versie, wordt de opstartlader niet gedegradeerd. De bijgewerkte opstartlader ondersteunt alle vorige releases.
Voor volgende versies van Cisco IOS® XE Everest 16.x.x kan een nieuwe opstartlader in die versie automatisch worden bijgewerkt op basis van de hardwareversie van de switch wanneer u uw switch voor het eerst opstart met het nieuwe image.
Op het moment dat u een upgrade uitvoert van Cisco IOS® XE Everest 16.6.1 naar 16.6.2, kan de upgrade enige tijd duren terwijl het systeem driemaal wordt gereset vanwege de gebruikelijke en Complex Programmable Logic Device (CPLD) -upgrade. De stateful switchover wordt ondersteund door Cisco IOS® XE Everest 16.6.2.
Verschillende manieren om Supervisor op te starten
In de Catalyst 9400-switch kunt u de supervisor opstarten met behulp van twee methoden:
- Installatiemodus
- Traditionele methode om het apparaat op te starten vanaf het .bin-bestand
Wanneer de switch in de installatiemodus wordt uitgevoerd, worden de Cisco IOS® XE-pakketbestanden (.pkg) en het provisioningbestand (packages.conf) opgeslagen in het flashgeheugen van de systeemkaart (flash:). Wanneer de switch wordt opgestart met behulp van het .bin-bestand, wordt het opgestart Cisco IOS® XE-softwarebundelbestand (.bin) opgeslagen in het flashgeheugen van de systeemkaart (flash:).
Na de 16.6.2-upgrade werkt de procedure onafhankelijk van de opstartmethode die is gebruikt om de switch op te starten op het huidige 16.6.1-image. De procedure hier upgradet echter de supervisor-engine naar de installatiemodus.
Upgradestappen voor primaire supervisor
Stap 1. Ongewenste pakketten verwijderen
Switch#install remove inactive Cleaning up unnecessary package files No path specified, can use booted path flash:packages.conf Cleaning flash: Scanning boot directory for packages ... done. Preparing packages list to delete ... cat9k-cc_srdriver.16.06.01.SPA.pkg File is in use, cannot delete. cat9k-espbase.16.06.01.SPA.pkg File is in use, can not delete. cat9k-rpbase.16.06.01.SPA.pkg File is in use, cannot delete. cat9k-rpboot.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipspa.16.06.01.SPA.pkg File is in use, will not delete. cat9k-srdriver.B16.06.01.SPA.pkg File is in use, will not delete. cat9k-webui.16.06.01.SPA.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. The following files will be deleted: [R0]: /flash/cat9k-cc_srdriver.16.06.01.SPA.pkg /flash/cat9k-espbase.16.06.01.SPA.pkg /flash/cat9k-rpbase.16.06.01.SPA.pkg /flash/cat9k-rpboot.16.06.01.SPA.pkg /flash/cat9k-sipbase.16.06.01.SPA.pkg /flash/cat9k-sipspa.16.06.01.SPA.pkg /flash/cat9k-srdriver.16.06.01.SPA.pkg /flash/cat9k-webui.16.06.01.SPA.pkg /flash/cat9k_1.bin /flash/cat9k_1.conf /flash/cat9k_2.1.conf /flash/cat9k_2.bin /flash/cat9k_2.conf /flash/cat9k_iosxe.16.06.01.SSA.bin /flash/packages.conf.00- Do you want to remove the above files? [y/n]y [R0]: Deleting file flash:cat9k-cc_srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-espbase.16.06.01.SPA.pkg ... done. Deleting file Deleting file flash:cat9k-rpbase.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-rpboot.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipbase.B16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipspa.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-webui.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k_1.bin ... done. Deleting file flash:cat9k_1.conf ... done. Deleting file flash:cat9k_2.1.conf ... done. Deleting file flash:cat9k_2.bin ... done. Deleting file flash:cat9k_2.conf ... done. Deleting file flash:cat9k_iosxe.16.06.01.SSA.bin ... done. Deleting file flash:packages.conf.00- ... done. SUCCESS: Files deleted. --- Starting Post_Remove_Cleanup --- Performing Post_Remove_Cleanup on Active/Standby [R0] Post_Remove_Cleanup package(s) on R0 [R0] Finished Post_Remove_Cleanup on R0 Checking status of Post_Remove_Cleanup on [R0] Post_Remove_Cleanup: Passed on [R0] Finished Post_Remove_Cleanup SUCCESS: install_remove Tue Jun 20 14:16:29 PDT 2017
Stap 2. Nieuwe afbeelding naar Flash kopiëren
In dit voorbeeld kopieert u de afbeelding van de TFTP-server naar de supervisors bootflash:
Switch#copy tftp: bootflash: Address or name of remote host []? 172.16.53.46 Source filename []? cat9k_iosxe.16.06.02.SPA.bin Destination filename [cat9k_iosxe.16.06.02.SPA.bin]? Accessing tftp://172.16.53.46//cat9k_iosxe.16.06.02.SPA.bin... Loading /cat9k_iosxe.16.06.02.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 601216545 bytes] 601216545 bytes copied in 50.649 secs (11870255 bytes/sec)
Step 3. Use the dir flash command to confirm that the image has been successfully copied to flash. Switch#dir bootflash:*.bin Directory of bootflash:/*.bin Directory of flash:/ 434184 -rw- 601216545 Jul 26 2017 10:18:11 -07:00 cat9k_iosxe.16.06.02.SPA.bin 11353194496 bytes total (8976625664 bytes free)
Stap 3. Controleer de opstartinstructie
Zorg ervoor dat de instructie boot is geconfigureerd voor packages.conf voordat u een upgrade uitvoert naar 16.6.2 in de installatiemodus. Als het is ingesteld op het .bin-bestand, moet u het wijzigen in packages.conf.:
Switch#show boot
BOOT variable = bootflash:cat9k_iosxe.16.06.01.SPA.bin;
Configuration Register is 0x102
MANUAL_BOOT variable = no
BAUD variable = 9600
ENABLE_BREAK variable does not exist
CONFIG_FILE variable does not exist
Change boot variable to point to packages.conf
Switch(config)#no boot system
Switch(config)#boot system bootflash:packages.conf
*Nov 14 15:12:50.043: %SYS-5-CONFIG_I: Configured from console by consol
Please save the configuration to reflect the new boot variable.
Switch#wr mem
Building configuration...
[OK]
Switch#show boot
BOOT variable = bootflash:packages.conf;
Configuration Register is 0x102
MANUAL_BOOT variable = no >> If manual variable is set to no, it means system is set to auto boot
BAUD variable = 9600
ENABLE_BREAK variable does not exist
CONFIG_FILE variable does not exist
You can set the system to auto boot or manual boot by setting the variables:
Changing system to auto boot
Switch(config)#no boot manual
Changing system to manual boot
Switch(config)#boot manual
If your switches are configured with auto boot, then the switch will automatically boot up with the new image when the switch is
reloaded. If your switches are not configured with auto boot and the switch is reloaded, you will receive a Rommon prompt
where you must then manually boot the new image flash:packages.conf
Switch: boot flash:packages.conf"
Stap 4. Software Installeer afbeelding naar Flash
Gebruik de opdracht Bestand toevoegen activeren om de doelafbeelding te installeren op Flash. U kunt naar de bronafbeelding op uw TFTP-server verwijzen of in opstartflash als u de afbeelding naar flash hebt gekopieerd. In dit voorbeeld hebt u de afbeelding al naar de flitser gekopieerd.
Switch#install add file bootflash:cat9k_iosxe.16.06.02.SPA.bin activate commit install_add_activate_commit: START Fri Nov 13 22:34:41 UTC 2017 *Nov 13 22:34:21.543: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:34:21 install_engine.sh: %INSTALL-5-INSTALL_START_INFO: Started install one-shot flash:cat9k_iosxe.16.06.02.SPA.bininstall_add_activate_commit: Adding PACKAGE
This operation requires a reload of the system. Do you want to proceed?
Please confirm you have changed boot config to flash:packages.conf [y/n]y
--- Starting Add ---
Performing Add on Active/Standby
[R0] Add package(s) on R0
[R0] Finished Add on R0
Checking status of Add on [R0]
Add: Passed on [R0]
Finished Add
install_add_activate_commit: Activating PACKAGE
*Nov 13 22:37:09.730: %IOSXE-4-PLATFORM: R0/0: kernel: ISOFS: Unable to identify CD-ROM format.Following packages shall be activated:
/flash/cat9k-wlc.16.06.02.SPA.pkg
/flash/cat9k-webui.16.06.02.SPA.pkg
/flash/cat9k-srdriver.16.06.02.SPA.pkg
/flash/cat9k-sipspa.16.06.02.SPA.pkg
/flash/cat9k-sipbase.16.06.02.SPA.pkg
/flash/cat9k-rpboot.16.06.02.SPA.pkg
/flash/cat9k-rpbase.16.06.02.SPA.pkg
/flash/cat9k-guestshell.16.06.02.SPA.pkg
/flash/cat9k-espbase.16.06.02.SPA.pkg
/flash/cat9k-cc_srdriver.16.06.02.SPA.pkg
This operation requires a reload of the system. Do you want to proceed? [y/n]y
--- Starting Activate ---
Performing Activate on Active/Standby
[R0] Finished Activate on R0
Checking status of Activate on [R0]
Activate: Passed on [R0]
Finished Activate
--- Starting Commit ---
Performing Commit on Active/Standby
*Nov 13 22:38:40.654: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:38:40 rollback_timer.sh: %INSTALL-5-INSTALL_AUTO_ABORT_TIMER_PROGRESS: Install auto abort timer will expire in 7200 seconds [R0] Commit package(s) on R0
[R0] Finished Commit on R0
Checking status of Commit on [R0]
Commit: Passed on [R0]
Finished Commit
Install will reload the system now!
SUCCESS: install_add_activate_commit Mon Nov 13 22:39:07 UTC 2017
*Nov 13 22:39:07.715: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:39:07 install_engine.sh: %INSTALL-5-INSTALL_COMPLETED_INFO: Completed install one-shot PACKAGE flash:cat9k_iosxe.16.06.02.SPA.binNov 13 22:39:2
Initializing Hardware...
System Bootstrap, Version 16.6.1r [FC2], RELEASE SOFTWARE (P)
Compiled Sat 07/15/2017 10:06:12.23 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Warning: ignoring ROMMON var "USER_BOOT_PARAM"
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): ### Mon Nov 13 22:42:05 Universal 2017 PLEASE DO NOT POWER CYCLE ### BOOT LOADER UPGRADING
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): boot loader upgrade successful <<< Bootloader upgrade done
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): Reloading the Supervisor to enable the New BOOTLOADER
Initializing Hardware...
Initializing Hardware...
Initializing Hardware...
System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P)
Compiled Tue 10/31/2017 11:38:44.98 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
######################################################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Warning: ignoring ROMMON var "USER_BOOT_PARAM"
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
Stap 5. Nieuwe pakketten en image controleren na upgrade
Nadat de software met succes is geïnstalleerd, controleert u of de flash-partitie de nieuwe .pkg-bestanden heeft. Steekproefuitvoer:
Switch#dir bootflash:*.pkg
Directory of bootflash:/*.pkg
Directory of bootflash:/
405607 -rw- 5186504 Nov 13 2017 22:36:25 +00:00 cat9k-cc_srdriver.16.06.02.SPA.pkg
405608 -rw- 76649412 Nov 13 2017 22:36:27 +00:00 cat9k-espbase.16.06.02.SPA.pkg
405609 -rw- 1536964 Nov 13 2017 22:36:27 +00:00 cat9k-guestshell.16.06.02.SPA.pkg
405610 -rw- 380625856 Nov 13 2017 22:36:38 +00:00 cat9k-rpbase.16.06.02.SPA.pkg
405616 -rw- 29580684 Nov 13 2017 22:36:48 +00:00 cat9k-rpboot.16.06.02.SPA.pkg
405611 -rw- 27612100 Nov 13 2017 22:36:39 +00:00 cat9k-sipbase.16.06.02.SPA.pkg
405614 -rw- 12268480 Nov 13 2017 22:36:41 +00:00 cat9k-webui.16.06.02.SPA.pkg
405612 -rw- 54981568 Nov 13 2017 22:36:40 +00:00 cat9k-sipspa.16.06.02.SPA.pkg
405613 -rw- 6521796 Nov 13 2017 22:36:40 +00:00 cat9k-srdriver.16.06.02.SPA.pkg
405615 -rw- 1536960 Nov 13 2017 22:36:41 +00:00 cat9k-wlc.16.06.02.SPA.pkg
11250098176 bytes total (8812113920 bytes free)
Stap 6. Versie en nieuwe bootloader controleren
Wanneer het nieuwe image wordt opgestart, controleert u de versie van het nieuwe image met behulp van de opdracht versie weergeven:
Switch#show version
Cisco IOS® XE Software, Version 16.06.02
Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
Cisco IOS® XE software, Copyright (c) 2005-2017 by Cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS®-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P)
Switch uptime is 20 minutes
Uptime for this control processor is 22 minutes
System returned to ROM by reload
System image file is "bootflash:packages.conf"
Last reload reason: EHSA standby down
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products can be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
-----------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
network-advantage Permanent network-advantage
cisco C9410R (X86) processor (revision V01) with 869104K/6147K bytes of memory.
Processor board ID FXS2130Q28F
2 Virtual Ethernet interfaces
192 Gigabit Ethernet interfaces
16 Ten Gigabit Ethernet interfaces
4 Forty Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
15958488K bytes of physical memory.
11161600K bytes of Bootflash at bootflash:.
1638400K bytes of Crash Files at crashinfo:.
0K bytes of WebUI ODM Files at webui:.
Configuration register is 0x2
Switch#show module
Chassis Type: C9410R
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+--------------+--------------
1 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409NQ
2 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409N2
3 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1R
4 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1C
5 10 Supervisor 1 Module C9400-SUP-1 JAE2124023Z
Mod MAC addresses Hw Fw Sw Status
---+--------------------------------+----+------------+------------------+--------
1 E4AA.5D59.8420 to E4AA.5D59.844F 1.0 16.6.2r[FC1 16.06.02 ok
2 E4AA.5D59.85AC to E4AA.5D59.85DB 1.0 16.6.2r[FC1 16.06.02 ok
3 E4AA.5D59.BC0C to E4AA.5D59.BC3B 1.0 16.6.2r[FC1 16.06.02 ok
4 E4AA.5D59.B72C to E4AA.5D59.B75B 1.0 16.6.2r[FC1 16.06.02 ok
5 2C5A.0F1C.4F2C to 2C5A.0F1C.4F35 0.6 16.6.2r[FC1 16.06.02 ok
Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode
---+-------------------+-------------------------+---------------------------
5 Active active sso
Upgradestappen voor secundaire supervisor
Verwijder de supervisor uit sleuf 5, die in de vorige stappen is bijgewerkt, en plaats de standby-supervisor in sleuf 6 in het chassis. Het verwijderen van de eerste supervisor is belangrijk omdat twee supervisors moeten worden geüpgraded terwijl beide in het chassis worden geplaatst; dit wordt niet ondersteund zoals eerder vermeld. U kunt dezelfde upgradestappen als gedocumenteerd herhalen om de nieuw geplaatste supervisor te upgraden.
Stap 1. Ongewenste pakketten verwijderen
Switch#install remove inactive Cleaning up unnecessary package files No path specified, will use booted path flash:packages.conf Cleaning flash: Scanning boot directory for packages ... done. Preparing packages list to delete ... cat9k-cc_srdriver.16.06.01.SPA.pkg File is in use, will not delete. cat9k-espbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-rpbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-rpboot.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipspa.16.06.01.SPA.pkg File is in use, will not delete. cat9k-srdriver.B16.06.01.SPA.pkg File is in use, will not delete. cat9k-webui.16.06.01.SPA.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. The following files will be deleted: [R0]: /flash/cat9k-cc_srdriver.16.06.01.SPA.pkg /flash/cat9k-espbase.16.06.01.SPA.pkg /flash/cat9k-rpbase.16.06.01.SPA.pkg /flash/cat9k-rpboot.16.06.01.SPA.pkg /flash/cat9k-sipbase.16.06.01.SPA.pkg /flash/cat9k-sipspa.16.06.01.SPA.pkg /flash/cat9k-srdriver.16.06.01.SPA.pkg /flash/cat9k-webui.16.06.01.SPA.pkg /flash/cat9k_1.bin /flash/cat9k_1.conf /flash/cat9k_2.1.conf /flash/cat9k_2.bin /flash/cat9k_2.conf /flash/cat9k_iosxe.16.06.01.SSA.bin /flash/packages.conf.00- Do you want to remove the above files? [y/n]y [R0]: Deleting file flash:cat9k-cc_srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-espbase.16.06.01.SPA.pkg ... done. Deleting file Deleting file flash:cat9k-rpbase.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-rpboot.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipbase.B16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipspa.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-webui.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k_1.bin ... done. Deleting file flash:cat9k_1.conf ... done. Deleting file flash:cat9k_2.1.conf ... done. Deleting file flash:cat9k_2.bin ... done. Deleting file flash:cat9k_2.conf ... done. Deleting file flash:cat9k_iosxe.16.06.01.SSA.bin ... done. Deleting file flash:packages.conf.00- ... done. SUCCESS: Files deleted. --- Starting Post_Remove_Cleanup --- Performing Post_Remove_Cleanup on Active/Standby [R0] Post_Remove_Cleanup package(s) on R0 [R0] Finished Post_Remove_Cleanup on R0 Checking status of Post_Remove_Cleanup on [R0] Post_Remove_Cleanup: Passed on [R0] Finished Post_Remove_Cleanup SUCCESS: install_remove Tue Jun 20 14:16:29 PDT 2017
Stap 2. Nieuwe afbeelding naar Flash kopiëren
In dit voorbeeld kopieert u de afbeelding van uw TFTP-server naar de Flash-supervisors.
Switch#copy tftp: bootflash: Address or name of remote host []? 172.16.53.46 Source filename []? cat9k_iosxe.16.06.02.SPA.bin Destination filename [cat9k_iosxe.16.06.02.SPA.bin]? Accessing tftp://172.16.53.46//cat9k_iosxe.16.06.02.SPA.bin... Loading /cat9k_iosxe.16.06.02.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 601216545 bytes] 601216545 bytes copied in 50.649 secs (11870255 bytes/sec) Step 3 Use the dir flash command to confirm that the image has been successfully copied to flash. Switch#dir bootflash:*.bin Directory of bootflash:/*.bin Directory of flash:/ 434184 -rw- 601216545 Jul 26 2017 10:18:11 -07:00 cat9k_iosxe.16.06.02.SPA.bin 11353194496 bytes total (8976625664 bytes free)
Stap 3. Opstartinstructie controleren
Zorg ervoor dat de instructie boot is geconfigureerd voor de packages.conf voordat u een upgrade uitvoert naar 16.6.2 in de installatiemodus. Als het is ingesteld op het .bin-bestand, moet u het wijzigen in packages.conf.:
Switch#show boot BOOT variable = bootflash:packages.conf; Configuration Register is 0x2 MANUAL_BOOT variable = no BAUD variable = 9600 ENABLE_BREAK variable = BOOTMODE variable does not exist IPXE_TIMEOUT variable does not exist CONFIG_FILE variable = If your switches are configured with auto boot, then the switch automatically boots up with the new image.
If not, you can manually boot flash:packages.conf Switch: boot flash:packages.conf
Stap 4. Software Installeer afbeelding naar Flash
Gebruik de opdracht Bestand toevoegen activeren om de doelafbeelding te installeren op Flash. U kunt naar de bronafbeelding op uw TFTP-server of in bootflash verwijzen als u de afbeelding naar flash hebt gekopieerd. In dit voorbeeld hebt u de afbeelding al naar de flitser gekopieerd.
Switch#install add file bootflash:cat9k_iosxe.16.06.02.SPA.bin activate commit
install_add_activate_commit: START Mon Nov 13 23:24:02 UTC 2017
System configuration has been modified.
Press Yes(y) to save the configuration and proceed.
Press No(n) for proceeding without saving the configuration.
Press Quit(q) to exit, you can save configuration and re-enter the command. [y/n/q]y
Building configuration...
[OK]Modified configuration has been saved
*Nov 13 23:24:09.935: %SYS-2-PRIVCFG_ENCRYPT: Successfully encrypted private config file
*Nov 13 23:24:11.314: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:24:11 install_engine.sh: %INSTALL-5-INSTALL_START_INFO: Started install one-shot flash:cat9k_iosxe.16.06.02.SPA.bininstall_add_activate_commit: Adding PACKAGE
This operation requires a reload of the system. Do you want to proceed?
Please confirm you have changed boot config to flash:packages.conf [y/n]y
--- Starting Add ---
Performing Add on Active/Standby
[R1] Add package(s) on R1
[R1] Finished Add on R1
Checking status of Add on [R1]
Add: Passed on [R1]
Finished Add
install_add_activate_commit: Activating PACKAGE
*Nov 13 23:25:28.589: %IOSXE-4-PLATFORM: R1/0: kernel: ISOFS: Unable to identify CD-ROM format.Following packages shall be activated:
/flash/cat9k-wlc.16.06.02.SPA.pkg
/flash/cat9k-webui.16.06.02.SPA.pkg
/flash/cat9k-srdriver.16.06.02.SPA.pkg
/flash/cat9k-sipspa.16.06.02.SPA.pkg
/flash/cat9k-sipbase.16.06.02.SPA.pkg
/flash/cat9k-rpboot.16.06.02.SPA.pkg
/flash/cat9k-rpbase.16.06.02.SPA.pkg
/flash/cat9k-guestshell.16.06.02.SPA.pkg
/flash/cat9k-espbase.16.06.02.SPA.pkg
/flash/cat9k-cc_srdriver.16.06.02.SPA.pkg
This operation requires a reload of the system. Do you want to proceed? [y/n]y
--- Starting Activate ---
Performing Activate on Active/Standby
[R1] Activate package(s) on R1
head: invalid number of lines: '/tmp/Activate.rp-1-1-1.20171113232845.out.log'
[R1] Finished Activate on R1
Checking status of Activate on [R1]
Activate: Passed on [R1]
Finished Activate
--- Starting Commit ---
Performing Commit on Active/Standby
*Nov 13 23:28:47.521: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:28:47 rollback_timer.sh: %INSTALL-5-INSTALL_AUTO_ABORT_TIMER_PROGRESS: Install auto abort timer will expire in 7200 seconds[R1] Commit package(s) on R1
[R1] Finished Commit on R1
Checking status of Commit on [R1]
Commit: Passed on [R1]
Finished Commit
Install will reload the system now!
SUCCESS: install_add_activate_commit Mon Nov 13 23:29:14 UTC 2017
Switch#
*Nov 13 23:29:14.578: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:29:14 install_engine.sh: %INSTALL-5-INSTALL_COMPLETED_INFO: Completed install one-shot PACKAGE flash:cat9k_iosxe.16.06.02.SPA.binNov 13 23:29:27
Initializing Hardware...
System Bootstrap, Version 16.6.1r [FC2], RELEASE SOFTWARE (P)
Compiled Sat 07/15/2017 10:06:12.23 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): ### Mon Nov 13 23:32:20 Universal 2017 PLEASE DO NOT POWER CYCLE ### BOOT LOADER UPGRADING
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): boot loader upgrade successful << Bootloader upgrade done
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): Reloading the Supervisor to enable the New BOOTLOADER
Initializing Hardware...
Initializing Hardware...
Initializing Hardware...
System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P)
Compiled Tue 10/31/2017 11:38:44.98 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
Stap 5. Nieuwe pakketten en image na upgrade controleren
Nadat de software met succes is geïnstalleerd, controleert u of de flash-partitie de nieuwe .pkg-bestanden heeft. Steekproefuitvoer:
Switch#dir bootflash:*.pkg Directory of bootflash:/*.pkg Directory of bootflash:/ 405607 -rw- 5186504 Nov 13 2017 22:36:25 +00:00 cat9k-cc_srdriver.16.06.02.SPA.pkg 405608 -rw- 76649412 Nov 13 2017 22:36:27 +00:00 cat9k-espbase.16.06.02.SPA.pkg 405609 -rw- 1536964 Nov 13 2017 22:36:27 +00:00 cat9k-guestshell.16.06.02.SPA.pkg 405610 -rw- 380625856 Nov 13 2017 22:36:38 +00:00 cat9k-rpbase.16.06.02.SPA.pkg 405616 -rw- 29580684 Nov 13 2017 22:36:48 +00:00 cat9k-rpboot.16.06.02.SPA.pkg 405611 -rw- 27612100 Nov 13 2017 22:36:39 +00:00 cat9k-sipbase.16.06.02.SPA.pkg 405614 -rw- 12268480 Nov 13 2017 22:36:41 +00:00 cat9k-webui.16.06.02.SPA.pkg 405612 -rw- 54981568 Nov 13 2017 22:36:40 +00:00 cat9k-sipspa.16.06.02.SPA.pkg 405613 -rw- 6521796 Nov 13 2017 22:36:40 +00:00 cat9k-srdriver.16.06.02.SPA.pkg 405615 -rw- 1536960 Nov 13 2017 22:36:41 +00:00 cat9k-wlc.16.06.02.SPA.pkg 11250098176 bytes total (8812113920 bytes free)
Aangezien beide toezichthouders afzonderlijk worden geüpgraded, moet de eerste toezichthouder in sleuf 5 worden geplaatst, aangezien deze als standby-toezichthouder moet toetreden:
Checking module status with both supervisors inserted Switch#show module Chassis Type: C9410R Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+--------------+-------------- 1 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409NQ 2 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409N2 3 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1R 4 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1C 5 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 6 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 E4AA.5D59.8420 to E4AA.5D59.844F 1.0 16.6.2r[FC1 16.06.02 ok 2 E4AA.5D59.85AC to E4AA.5D59.85DB 1.0 16.6.2r[FC1 16.06.02 ok 3 E4AA.5D59.BC0C to E4AA.5D59.BC3B 1.0 16.6.2r[FC1 16.06.02 ok 4 E4AA.5D59.B72C to E4AA.5D59.B75B 1.0 16.6.2r[FC1 16.06.02 ok 5 2C5A.0F1C.4F2C to 2C5A.0F1C.4F35 0.6 16.6.2r[FC1 16.06.02 ok 6 2C5A.0F1C.4F36 to 2C5A.0F1C.4F3F 0.6 16.6.2r[FC1 16.06.02 ok Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode ---+-------------------+-------------------------+--------------------------- 5 Standby standby hot sso 6 Active active sso
Redundantie controleren
De supervisor-modules in de Catalyst 9400 (hardware) ondersteunen redundantie. Softwareredundantie wordt ondersteund in Cisco IOS ® XE Everest 16.6.2. In de 16.6.2-softwareversie wordt de functie Route Processor Redundancy (RPR) niet ondersteund. Gebruik de opdrachten voor showredundantie en showplatformsoftware-iomd-redundantie om ervoor te zorgen dat zowel Stateful Switchover (SSO) als IOMD klaar is voordat u switchovers voltooit.
RPR-redundantie
Wanneer een stand-by supervisor-engine in de RPR-modus draait, wordt deze gestart in een gedeeltelijk geïnitialiseerde toestand en gesynchroniseerd met de permanente configuratie van de actieve supervisor-engine. RPR wordt niet ondersteund in 16.6.2.
In het geval van een omschakeling van de supervisor-motor wordt het verkeer verstoord omdat in de RPR-modus alle fysieke poorten opnieuw worden opgestart, omdat er geen staat wordt gehandhaafd tussen de supervisor-motoren die betrekking heeft op moduletypen en -statussen. Bij de omschakeling, wanneer de stand-by supervisor-engine de initialisatie voltooit, leest deze hardware-informatie rechtstreeks uit de module en wordt de actieve supervisor-engine.
SSO-redundantie
Wanneer een stand-by supervisor-engine in de SSO-modus draait, wordt de stand-by supervisor-engine gestart in een volledig geïnitialiseerde toestand en gesynchroniseerd met de permanente configuratie en de actieve supervisor-engine. Het onderhoudt vervolgens de status van de hier vermelde protocollen en alle wijzigingen in de hardware- en softwarestatus voor functies die stateful switchover ondersteunen, worden gesynchroniseerd gehouden.
Bijgevolg biedt het geen onderbreking van Layer 2-sessies in een redundante configuratie van de supervisor-engine.
Omdat de standby supervisor-engine de status van de hardwarekoppeling van elke koppeling herkent, blijven poorten die actief waren voordat de omschakeling plaatsvond actief, inclusief de uplinkpoorten. Omdat uplinkpoorten fysiek op de supervisor-engine staan, kunnen ze echter worden losgekoppeld als de supervisor-engine wordt verwijderd.
Als de actieve supervisor-engine uitvalt, wordt de stand-by supervisor-engine actief. Deze nieuw actieve supervisor-engine maakt gebruik van bestaande Layer 2-switchinginformatie om het verkeer door te sturen.
IOMD is Input Output Module Driver software process. Check if IOMds are ready and have initialized Software/hardware.
Switch# show platform software iomd redundancy
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Local RF state = ACTIVE
Peer RF state = STANDBY HOT
slot PSM STATE SPA INTF HA_STATE HA_ACTIVE
1 ready started ready 00:10:49
2 ready started ready 00:10:49
3 ready started ready 00:10:48
4 ready started ready 00:10:49
5 ready started ready 00:10:54
6 ready started ready 00:10:53 ***active RP
Switch#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 31 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 6
Current Software state = ACTIVE
Uptime in current state = 31 minutes
Image Version = Cisco IOS ®Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
BOOT = bootflash:packages.conf;
CONFIG_FILE =
Configuration register = 0x2
Peer Processor Information :
----------------------------
Standby Location = slot 5
Current Software state = STANDBY HOT
Uptime in current state = 26 minutes
Image Version = Cisco IOS ®Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
BOOT = bootflash:packages.conf;
CONFIG_FILE =
Configuration register = 0x2
Revisiegeschiedenis
| Revisie | Publicatiedatum | Opmerkingen |
|---|---|---|
4.0 |
09-Jun-2026
|
Bijgewerkte spelling, spatiëring, grammatica, zinsstructuur, inleiding en titel. |
3.0 |
20-Nov-2024
|
Opmaak bijgewerkt. |
2.0 |
05-May-2023
|
Bijgewerkte titel, Branding eisen, Machine vertaling, Grondslagen, Stijl eisen, en opmaak. |
1.0 |
16-Nov-2017
|
Eerste vrijgave |
Feedback