이 문서에서는 2950/2955/2970/2940/2900XL/3500XL 스위치와 Catalyst OS(CatOS)를 실행하는 Catalyst 4500/4000 스위치를 포함하는 Catalyst Layer 2(L2) 고정 구성 스위치 간의 트렁크 링크인 EtherChannel 링크 설정에 대한 샘플 구성 및 명령 구조를 제공합니다. 이 시나리오에서 CatOS를 실행하는 모든 Catalyst 4500/4000, 5500/5000 또는 6500/6000 Series 스위치로 Catalyst L2 고정 구성 스위치를 구성하여 동일한 결과를 얻을 수 있습니다. 현재 네트워크에서 고속 이더넷이 인기를 끌면서 샘플 컨피그레이션에서는 고속 이더넷을 사용합니다. 이 샘플은 각 스위치에서 2개의 고속 이더넷 포트를 FEC(Fast EtherChannel)로 번들링하고 FEC 위에 IEEE 802.1Q(dot1q) 트렁킹을 구성합니다.
이 문서에서는 동일한 용어인 EtherChannel을 사용하여 FEC, GEC(Gigabit EtherChannel), 포트 채널, 채널 및 포트 그룹을 나타냅니다. 스위치에서 EtherChannel을 구성하는 방법에 대한 자세한 내용은 다음 문서를 참조하십시오.
Catalyst 4000 스위치에서 Fast EtherChannel 및 Gigabit EtherChannel 구성
Catalyst 2950 스위치에서 EtherChannel 구성
Catalyst 2950/2955 스위치에서 EtherChannel 구성
Catalyst 2970 스위치에서 EtherChannel 구성
Catalyst 2940 스위치에서 EtherChannel 구성
이 문서의 정보는 다음 소프트웨어 및 하드웨어 버전을 기반으로 합니다.
Cisco IOS® Software 릴리스 12.1(6)EA2c를 실행하는 Catalyst 2950
Cisco IOS Software 릴리스 12.1(12c)EA1을 실행하는 Catalyst 2955
Cisco IOS Software 릴리스 12.1(22)EA1을 실행하는 Catalyst 2940
Cisco IOS Software 릴리스 12.1(19)EA1c를 실행하는 Catalyst 2970
Cisco IOS 소프트웨어 릴리스 12.0(5)WC9를 실행하는 Catalyst 2900XL/3500XL
CatOS 버전 8.4.1을 실행하는 Catalyst 4000
이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우, 모든 명령어의 잠재적인 영향을 미리 숙지하시기 바랍니다.
문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 표기 규칙을 참조하십시오.
Catalyst L2 고정 컨피그레이션 스위치와 CatOS를 실행하는 Catalyst 4500/4000 제품군(Catalyst 4003/4006/2948G/2980G)을 사용할 경우, 이 스위치는 dot1q 트렁킹 캡슐화만 지원합니다. 다른 Catalyst 플랫폼은 dot1q 및 ISL(Inter-Switch Link Protocol)을 모두 지원합니다. dot1q는 IEEE 표준이지만 ISL은 Cisco의 독점 기술입니다. Cisco 하드웨어에서만 ISL 트렁킹 캡슐화를 지원할 수 있습니다. Catalyst 5500/5000 또는 Catalyst 6500/6000과 같은 다른 Cisco 스위칭 플랫폼을 사용하고 어떤 트렁킹 방법이 지원되는지 확인해야 하는 경우 다음 명령을 실행합니다.
show port capabilities mod/port
특정 포트 및 특정 포트에 있는 기능(예: dot1q, ISL, 포트 채널)에 대한 자세한 내용은 다음을 참조하십시오.
EtherChannel은 PAgP(Port Aggregation Protocol) 또는 LACP(Link Aggregation Control Protocol)를 사용하여 자동 컨피그레이션을 수행합니다. EtherChannel을 수동으로 구성할 수도 있습니다. PAgP는 Cisco 스위치 및 라이센스 공급업체가 PAgP 지원 라이센스를 부여하는 스위치에서만 실행할 수 있는 Cisco 전용 프로토콜입니다. IEEE 802.3ad는 LACP를 정의합니다. LACP를 통해 Cisco 스위치는 802.3ad 프로토콜을 따르는 스위치 간 이더넷 채널을 관리할 수 있습니다. 최대 16개의 포트를 구성하여 채널을 구성할 수 있습니다. 포트 중 8개는 액티브 모드이고 나머지 8개는 스탠바이 모드입니다. 활성 포트 중 하나에 장애가 발생하면 대기 포트는 활성 포트가 됩니다. 스탠바이 모드는 PAgP가 아닌 LACP에서만 작동합니다.
이러한 프로토콜 중 하나를 사용하는 경우 스위치는 PAgP 또는 LACP를 지원할 수 있는 파트너의 ID를 학습하고 각 인터페이스의 기능을 학습합니다. 그런 다음 유사한 컨피그레이션의 인터페이스를 단일 논리적 링크(채널 또는 종합 포트)로 동적으로 그룹화합니다. 이 스위치는 하드웨어, 관리 및 포트 매개변수 제약을 기반으로 합니다. 예를 들어, PAgP는 동일한 속도, 이중 모드, 기본 VLAN, VLAN 범위, 트렁킹 상태 및 유형으로 인터페이스를 그룹화합니다. PAgP가 링크를 EtherChannel로 그룹화한 후 PAgP는 그룹을 스패닝 트리에 단일 스위치 포트로 추가합니다.
스위치 | LACP 지원 | 최소 LACP 버전 및 지원 | PAgP 지원 | 최소 PAgP 버전 및 지원 |
---|---|---|---|---|
Catalyst 2940 | 예 | Cisco IOS Software 릴리스 12.1(19)EA1 | 예 | Cisco IOS Software 릴리스 12.1(13)AY |
Catalyst 2950 | 예 | Cisco IOS Software 릴리스 12.1(14)EA1 | 예 | Cisco IOS Software 릴리스 12.0(5.2)WC(1) |
Catalyst 2955 | 예 | Cisco IOS Software 릴리스 12.1(14)EA1 | 예 | Cisco IOS Software Release 12.1(12c)EA1 |
Catalyst 2970 | 예 | Cisco IOS Software 릴리스 12.2(18)SE | 예 | Cisco IOS Software 릴리스 12.1(11)AX |
Catalyst 2900XL | 아니요 | — | 아니요 | — |
Catalyst 3500XL | 아니요 | — | 아니요 | — |
이 섹션에서는 channel-group interface 컨피그레이션 명령에 대해 사용자 컨피그레이션 가능한 EtherChannel 모드를 나열합니다. 스위치 인터페이스는 자동 또는 바람직한 모드 컨피그레이션을 사용하는 파트너 인터페이스와만 PAgP 패킷을 교환합니다. 스위치 인터페이스는 액티브 또는 패시브 모드 컨피그레이션을 사용하는 파트너 인터페이스와만 LACP 패킷을 교환합니다. on 모드 컨피그레이션과의 인터페이스는 PAgP 또는 LACP 패킷을 교환하지 않습니다.
active — 인터페이스를 활성 협상 상태로 전환합니다. 이 경우 인터페이스는 LACP 패킷 전송을 통해 다른 인터페이스와의 협상을 시작합니다.
auto - 인터페이스를 패시브 협상 상태로 전환합니다. 이 경우 인터페이스가 수신한 PAgP 패킷에 응답하지만 PAgP 패킷 협상을 시작하지 않습니다. 이 설정은 PAgP 패킷의 전송을 최소화합니다.
desirable(권장) - 인터페이스를 활성 협상 상태로 전환합니다. 이 경우 인터페이스는 PAgP 패킷 전송을 통해 다른 인터페이스와의 협상을 시작합니다.
on - 인터페이스를 PAgP 또는 LACP 없이 EtherChannel에 강제 적용합니다. on 모드에서는 on 모드의 인터페이스 그룹이 on 모드의 다른 인터페이스 그룹에 연결된 경우에만 사용 가능한 EtherChannel이 있습니다.
passive - 인터페이스를 패시브 협상 상태로 만듭니다. 이 경우 인터페이스는 인터페이스가 수신한 LACP 패킷에 응답하지만 LACP 패킷 협상을 시작하지 않습니다. 이 설정은 LACP 패킷의 전송을 최소화합니다.
이 표에서 볼 수 있듯이 LACP 링크 집계를 실행하는 유효한 조합은 세 가지뿐입니다.
스위치 | 스위치 | 의견 |
---|---|---|
활성 | 활성 | 권장. |
활성 | 수동 | 협상이 성공하면 링크 집계가 발생합니다. |
on | on | 링크 집계가 LACP 없이 발생합니다. 이 방법은 작동하지만, 이러한 조합은 권장되지 않습니다. |
참고: 기본적으로 LACP 채널 컨피그레이션에서는 LACP 채널 모드가 패시브입니다.
PAgP는 FEC 링크의 자동 생성을 지원합니다. PAgP 패킷은 채널 형성을 협상하기 위해 FEC 가능 포트 간에 전송됩니다. PAgP에 의도적으로 도입된 몇 가지 제한 사항이 있습니다. 제한 사항은 다음과 같습니다.
PAgP는 동적 VLAN에 대한 컨피그레이션과 함께 포트에 번들을 형성하지 않습니다. PAgP를 사용하려면 채널의 모든 포트가 동일한 VLAN에 속하거나 포트에 트렁크 포트 컨피그레이션이 있어야 합니다. 번들이 이미 있고 포트의 VLAN을 수정하면 번들의 모든 포트가 해당 VLAN과 일치하도록 변경됩니다.
PAgP는 다른 속도 또는 포트 듀플렉스에서 작동하는 포트를 그룹화하지 않습니다. 번들이 있을 때 속도와 양방향을 변경하면 PAgP는 번들의 모든 포트에 대해 포트 속도와 양방향을 변경합니다.
PAgP 모드는 꺼짐, 자동, 바람직함, 등입니다. 자동-바람직함, 바람직함-바람직함, 및 온-온의 조합들만이 채널의 형성을 허용한다. 채널 한쪽의 디바이스가 PAgP를 지원하지 않는 경우(예: 라우터), 다른 쪽의 디바이스는 PAgP를 on으로 설정해야 합니다. Catalyst 2950 스위치는 Cisco IOS Software 릴리스 12.1(6)EA2 이상과의 채널 협상을 위해 PAgP를 지원합니다. Cisco IOS Software 릴리스 12.0은 정적 컨피그레이션만 지원합니다. CatOS를 실행하는 모든 Catalyst 스위치는 PAgP 프로토콜 채널 협상을 지원합니다.
다양한 유형의 트렁킹 프로토콜이 있습니다. 포트가 트렁크가 될 수 있는 경우 자동으로 트렁크하는 기능도 있을 수 있습니다. 경우에 따라 포트에서는 어떤 유형의 트렁킹을 포트에 사용할지 협상할 수도 있습니다. 다른 디바이스와 트렁킹 방법을 협상하는 이 기능에는 DTP(Dynamic Trunking Protocol)라는 이름이 있습니다.
Catalyst 2950 스위치는 Cisco IOS Software 릴리스 12.1(6)EA2 이상에서 동적 트렁킹을 위한 DTP를 지원합니다. Cisco IOS Software 릴리스 12.0은 정적 컨피그레이션만 지원합니다. CatOS를 실행하는 모든 Catalyst 스위치는 DTP를 지원합니다.
이 섹션에는 이 문서에서 설명하는 기능을 구성하기 위한 정보가 표시됩니다.
참고: 이 문서에 사용된 명령에 대한 추가 정보를 찾으려면 명령 조회 도구(등록된 고객만 해당)를 사용하십시오.
이 문서에서는 이 네트워크 설정을 사용합니다.
이 문서에서는 다음 설정을 사용합니다.
Catalyst 4000 |
---|
Cat4003 (enable) show channelprotocol Channel Module Protocol ------- -------- 2 PAGP Cat4003 (enable) !--- By default, all ports on a Catalyst 4500/4000 use channel protocol PAgP. !--- So, to run LACP, you must change the channel protocol to LACP. On switches !--- that run CatOS, you can only change the channel mode per module. In this !--- example, the command set channelprotocol lacp module_number !--- changes the channel mode for slot 2. Use the show channelprotocol command to !--- verify the changes. Cat4003 (enable) set channelprotocol lacp 2 Mod 2 is set to LACP protocol. Cat4003 (enable) Cat4003 (enable) set port lacp-channel 2/1-2 Port(s) 2/1-2 are assigned to admin key 80. Cat4003 (enable) !--- There is a parameter exchange in the LACP packet. The parameter is !--- the admin key. A channel can only form between ports that have !--- the same admin key. In this example, both ports have assignment to the same group. !--- (The random assignment is admin key 80.) !--- Keep in mind that the admin key is only locally significant. In other words, !--- the admin key must be the same only for ports within the switch and is not a factor !--- between different switches. Cat4003 (enable) set port lacp-channel 2/1-2 mode active Port(s) 2/1-2 channel mode set to active. Cat4003 (enable) To form the channel change the LACP channel mode to active state on one or both of the sides. Cat4003 (enable) set trunk 2/1 desirable dot1q Port(s) 2/1-2 trunk mode set to desirable. Port(s) 2/1-2 trunk type set to dot1q. Cat4003 (enable) !--- Configure the ports to the desirable trunk mode that makes the ports actively !--- attempt to convert the link to a trunk link. The ports become trunk ports if !--- the neighbor ports are in on, desirable, or auto mode. Cat4003 (enable) show config This command shows non-default configurations only. Use 'show config all' to show both default and non-default configurations. ................. ............................. .. begin !--- Output suppressed. #channelprotocol set channelprotocol lacp 2 ! #port channel set port lacp-channel 2/1-2 80 ! !--- Output suppressed. #module 2 : 48-port 10/100/1000 Ethernet set trunk 2/1 desirable dot1q 1-1005,1025-4094 set trunk 2/2 desirable dot1q 1-1005,1025-4094 ! !--- Output suppressed. |
Catalyst L2 고정 컨피그레이션 스위치 플랫폼의 컨피그레이션 명령은 동일합니다. 문서 길이를 적절하게 유지하기 위해 이 문서에는 플랫폼 중 하나에 대한 컨피그레이션이 표시됩니다(Catalyst 2955). 그러나 모든 명령에 대한 테스트는 모든 Catalyst L2 고정 구성 스위치 플랫폼에서 수행되었습니다.
Catalyst L2 고정 구성 스위치 |
---|
CAT2955# configure terminal Enter configuration commands, one per line. End with CNTL/Z. CAT2955(config)# interface fastethernet 0/9 CAT2955(config-if)# channel-group 1 mode active Creating a port-channel interface Port-channel 1 Assign the interface to a channel group, and specify the LACP mode. CAT2955(config-if)# 6d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9,changed state to down 6d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9,changed state to up 6d08h: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up 6d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1,changed state to up CAT2955(config-if)# interface fastethernet 0/10 CAT2955(config-if)# channel-group 1 mode active CAT2955(config-if)# 6d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10,changed state to down 6d08h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10,changed state to up CAT2955(config-if)# interface port-channel 1 CAT2955(config-if)# switchport mode trunk Configuring the port channel interface to be a trunk pulls fa 0/9-10 in. CAT2955(config-if)# ^Z CAT2955# show run 6d08h: %SYS-5-CONFIG_I: Configured from console by consolerun Building configuration... !--- Output suppressed. ! interface Port-channel1 switchport mode trunk no ip address flowcontrol send off fcs-threshold 0 ! !--- Output suppressed. interface FastEthernet0/9 switchport mode trunk no ip address channel-group 1 mode active ! interface FastEthernet0/10 switchport mode trunk no ip address channel-group 1 mode active ! !--- Output suppressed. end CAT2955# |
Catalyst L2 고정 구성 스위치 |
---|
5-2950# configure terminal Enter configuration commands, one per line. End with CNTL/Z. 5-2950(config)# interface fastethernet0/1 5-2950(config-if)# channel-group 1 mode desirable Creating a port-channel interface Port-channel1 !--- The software dynamically creates the port channel interface. 5-2950(config-if)# *Mar 16 13:50:56.185: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down *Mar 16 13:50:57.013: %EC-5-BUNDLE: Interface Fa0/1 joined port-channel Po1 *Mar 16 13:50:58.053: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up *Mar 16 13:50:59.021: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up *Mar 16 13:51:00.021: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to up 5-2950(config-if)# 5-2950(config)# interface fastethernet0/2 5-2950(config-if)# channel-group 1 mode desirable 5-2950(config-if)# 5-2950(config-if)# interface port-channel 1 !--- Configuration of the port channel interface to be a trunk !--- pulls in Fast Ethernet 0/1 and 0/2. 5-2950(config-if)# switchport mode trunk *Mar 14 15:31:13.428: %DTP-5-TRUNKPORTON: Port Fa0/1 has become dot1q trunk *Mar 14 15:31:14.880: %EC-5-BUNDLE: Interface Fa0/1 joined port-channel Po1 *Mar 14 15:31:14.908: %EC-5-UNBUNDLE: Interface Fa0/2 left the port-channel Po1 *Mar 14 15:31:14.944: %EC-5-BUNDLE: Interface Fa0/2 joined port-channel Po1 *Mar 14 15:31:15.908: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up 5-2950# show run Building configuration... Current configuration : 1608 bytes ! version 12.1 no service pad service timestamps debug uptime service timestamps log datetime msec localtime no service password-encryption ! hostname 5-2950 ! ! clock timezone PST -8 ip subnet-zero no ip finger no ip domain-lookup cluster enable SWITCH 0 ! ! ! interface Port-channel 1 !--- This is the port channel interface where you configure trunking that !--- the members of the channel group inherit. switchport mode trunk ! interface FastEthernet0/1 switchport mode trunk channel-group 1 mode desirable !--- Here, the channel group corresponds with interface port-channel 1. ! interface FastEthernet0/2 switchport mode trunk channel-group 1 mode desirable !--- Here, the channel group corresponds with interface port-channel 1. ! interface FastEthernet0/3 ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! |
Catalyst 4000 스위치 |
---|
Console> (enable) set port channel 2/19-20 mode desirable Port(s) 2/19-20 channel mode set to desirable. Console> (enable) 2003 Jan 08 11:40:14 %PAGP-5-PORTFROMSTP:Port 2/19 left bridge port 2/19 2003 Jan 08 11:40:14 %PAGP-5-PORTFROMSTP:Port 2/20 left bridge port 2/20 2003 Jan 08 11:40:18 %PAGP-5-PORTTOSTP:Port 2/19 joined bridge port 2/19 2003 Jan 08 11:40:18 %PAGP-5-PORTTOSTP:Port 2/20 joined bridge port 2/20 Console> (enable) set trunk 2/19 desirable !--- The set of the trunk on the first port of the channel !--- dynamically trunks all channel ports. Port(s) 2/19-20 trunk mode set to desirable. ! Console> (enable) !--- The dot1q trunk adopts the port VLAN assignment (VLAN 1 by default) !--- as the native VLAN. If this switch were a Catalyst 5500/5000 or 6500/6000 switch !--- (which also supports ISL trunking), you would specify dot1q encapsulation here. !--- The Catalyst 2950 only supports dot1q. |
이 섹션에서는 컨피그레이션이 제대로 작동하는지 확인하는 데 사용할 수 있는 정보를 제공합니다.
일부 show 명령은 출력 인터프리터 툴 에서 지원되는데(등록된 고객만), 이 툴을 사용하면 show 명령 출력의 분석 결과를 볼 수 있습니다. L2 고정 구성 스위치 플랫폼의 show 명령은 동일하지만 출력 형식은 다를 수 있습니다.
CAT2955# show etherchannel summary Flags: D - down P - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3 S - Layer2 u - unsuitable for bundling U - in use f - failed to allocate aggregator d - default port Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Fa0/9(P) Fa0/10(Pd) CAT2955# CAT2955# show interfaces fastethernet 0/9 switchport Name: Fa0/9 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk (member of bundle Po1) Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative private-vlan host-association: none Administrative private-vlan mapping: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Protected: false Voice VLAN: none (Inactive) Appliance trust: none
Cat4003 (enable) show lacp Channel Id Ports ----------- ----------------------------------------------- 417 2/1-2 Cat4003 (enable) show lacp-channel 417 Channel Ports Status Channel id Mode ------- ---------------------------------------------- ---------- -------------- 417 2/1-2 connected active Cat4003 (enable) Cat4003 (enable) show trunk * - indicates vtp domain mismatch # - indicates dot1q-all-tagged enabled on the port Port Mode Encapsulation Status Native vlan -------- ----------- ------------- ------------ ----------- 2/1 desirable dot1q trunking 1 2/2 desirable dot1q trunking 1 Port Vlans allowed on trunk -------- --------------------------------------------------------------------- 2/1 1-1005,1025-4094 2/2 1-1005,1025-4094 Port Vlans allowed and active in management domain -------- --------------------------------------------------------------------- 2/1 1,10 2/2 1,10 Port Vlans in spanning tree forwarding state and not pruned -------- --------------------------------------------------------------------- 2/1 1,10 2/2 1,10 Cat4003 (enable)
5-2950# show etherchannel summary Flags: D - down P - in port-channel I - stand-alone s - suspended R - Layer3 S - Layer2 U - port-channel in use Group Port-channel Ports -----+------------+----------------------------------------------------------- 1 Po6(SU) Fa0/1(P) Fa0/2(P) 5-2950# show interface fastethernet0/1 switchport Name: Fa0/1 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk (member of bundle Po6) Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) !--- This line shows that the trunk link is up. Trunking VLANs Enabled: ALL !--- This line shows that all VLANs trunk. Pruning VLANs Enabled: 2-1001 Protected: false Voice VLAN: none (Inactive) Appliance trust: none
Console> show port channel Port Status Channel Admin Ch Mode Group Id ----- ---------- -------------------- ----- ----- 2/19 connected desirable silent 174 815 2/20 connected desirable silent 174 815 ----- ---------- -------------------- ----- ----- Port Device-ID Port-ID Platform ----- ------------------------------- ------------------------- ---------------- 2/19 5-2950 Fa0/1 cisco WS-C2950-24 2/20 5-2950 Fa0/2 cisco WS-C2950-24 ----- ------------------------------- ------------------------- ---------------- Console> (enable) show trunk * - indicates vtp domain mismatch Port Mode Encapsulation Status Native vlan -------- ----------- ------------- ------------ ----------- 2/19 desirable dot1q trunking 1 2/20 desirable dot1q trunking 1 Port Vlans allowed on trunk -------- --------------------------------------------------------------------- 2/19 1-1005 2/20 1-1005 Port Vlans allowed and active in management domain -------- --------------------------------------------------------------------- 2/19 1,100,300,350,450 2/20 1,100,300,350,450 Port Vlans in spanning tree forwarding state and not pruned -------- --------------------------------------------------------------------- 2/19 1,100,300,350,450 2/20 1,100,300,350,450 Console> (enable)
현재 이 설정에 사용할 수 있는 특정 문제 해결 정보가 없습니다.
개정 | 게시 날짜 | 의견 |
---|---|---|
1.0 |
06-May-2002
|
최초 릴리스 |