Cisco Secure VPN Client Wild-Card에 PIX 구성, 사전 공유, No Mode-Config

PIX Version 6.2.1
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall
fixup protocol ftp 21
fixup protocol http 80
fixup protocol smtp 25
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol sqlnet 1521
names

!--- The ACL to bypass the NAT. You have to know the !--- IP address of the Client. In this case, it is !--- subnet 65.10.10.0/24.

access-list 103 permit ip 10.0.0.0 255.0.0.0 65.10.10.0 255.255.255.0
pager lines 24
no logging timestamp
no logging standby
logging console debugging
no logging monitor
no logging buffered
no logging trap
logging facility 20
logging queue 512
interface ethernet0 10baset
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside 192.68.0.10 255.255.255.0
ip address inside 10.1.1.3 255.255.255.0
no failover
failover timeout 0:00:00
failover ip address outside 0.0.0.0
failover ip address inside 0.0.0.0
arp timeout 14400
global (outside) 1 192.68.0.11-192.168.0.15 netmask 255.255.255.0

!--- Binding ACL 103 to the NAT statement in order to !--- avoid NAT on the IPSec packet.

nat (inside) 0 access-list 103
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) 192.68.0.50 10.1.1.50 netmask 255.255.255.255 0 0
conduit permit icmp any any
no rip outside passive
no rip outside default
no rip inside passive
no rip inside default
route outside 0.0.0.0 0.0.0.0 192.68.0.1 1
route inside 10.2.2.0 255.255.255.0 10.1.1.1 1
timeout xlate 3:00:00 conn 1:00:00 half-closed 0:10:00 udp 0:02:00
timeout rpc 0:10:00 h323 0:05:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps

!--- The sysopt ipsec pl-compatible command !--- avoids conduit on the IPSec encrypted traffic. !--- This command needs to be used if you do not use !--- the nat 0 access-list command.

sysopt ipsec pl-compatible
sysopt connection permit-ipsec
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto dynamic-map cisco 1 set transform-set myset
crypto map dyn-map 20 ipsec-isakmp dynamic cisco
crypto map dyn-map interface outside
isakmp enable outside
isakmp key cisco123 address 0.0.0.0 netmask 0.0.0.0
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 1
isakmp policy 10 lifetime 1000
telnet timeout 5
terminal width 80
Cryptochecksum:c687aa0afb1dd03abce04c31566b5c52
: end
[OK]

Network Security policy: 
 1- TACconn 
     My Identity 
          Connection security: Secure 
          Remote Party Identity and addressing 
          ID Type: IP subnet 
          10.0.0.0 
           255.0.0.0 
          Port all Protocol all 
 
     Connect using secure tunnel 
          ID Type: IP address 
          192.68.0.10 
 
     Authentication (Phase 1) 
     Proposal 1 
         Authentication method: pre-shared key 
         Encryp Alg: DES 
         Hash Alg: MD5 
         SA life: Unspecified 
         Key Group: DH 1 
 
 
     Key exchange (Phase 2) 
     Proposal 1 
         Encapsulation ESP 
         Encrypt Alg: DES 
         Hash Alg: MD5 
         Encap: tunnel 
         SA life: Unspecified 
         no AH 
 
 
 2- Other Connections 
        Connection security: Non-secure 
        Local Network Interface 
          Name: Any 
          IP Addr: Any 
          Port: All