소개
이 문서에서는 Cisco NCS 560 RP(Route Processor)가 다시 로드 또는 전원 사이클 후 응답하지 않는 상황을 방지하는 방법을 설명합니다.
배경 정보
대부분의 경우, NCS 560 구축은 많은 수의 원격 위치에 구축되며 사람의 개입을 최소화해야 합니다.
이러한 구축에서는 설치된 릴리스에 따라 필수 SMU 설치 요구 사항을 이행하는 것도 중요합니다.
참고: Cisco IOS XR 릴리스 7.2.2 이상에서는 더 이상 SMU를 별도로 설치할 필요가 없습니다.
SMU 요약 테이블
FPD 업그레이드 MOP
FPD가 항상 Cisco IOS® XR 릴리스에 필요한 최소 버전과 같거나 더 높은 버전인지 확인하려면 FPD를 업그레이드해야 합니다.
ADM
|
1.06
|
IOFPGA
|
0.64
|
바이오스
|
0.16
|
이 문서에서는 다음 사항을 가정합니다.
- RP0은 활성 RP입니다.
- RP1은 대기 RP입니다.
다양한 위치를 탐색하는 모든 명령이 생략되도록 다양한 위치를 묻는 프롬프트가 표시됩니다.
1. XR - RP0
RP/0/RP0/CPU0:ios#
2. XR - RP1
RP/0/RP1/CPU0:ios#
3 . sysadmin - RP0
sysadmin-vm:0_RP0#
4. sysadmin - RP1
sysadmin-vm:0_RP1#
5. sysadmin - RP0 셸
[sysadmin-vm:0_RP0:~]$
6. sysadmin - RP1 셸
[sysadmin-vm:0_RP1:~]$
사용 사례. Cisco IOS-XR 릴리스 7.1.2. 필요한 SMUS가 활성화된 시스템
이러한 SMU는 이 프로세스에 앞서 활성 상태여야 하며 시스템에 커밋되어야 합니다.
XR 가상 머신
RP/0/RP0/CPU0:ios#show install active summary
Active Packages: 10
ncs560-xr-7.1.2 version=7.1.2 [Boot image]
ncs560-mcast-2.0.0.0-r712
ncs560-mgbl-2.0.0.0-r712
ncs560-mpls-1.0.0.0-r712
ncs560-mpls-te-rsvp-2.0.0.0-r712
ncs560-ospf-2.0.0.0-r712
ncs560-k9sec-2.1.0.0-r712
ncs560-iosxr-fwding-2.1.0.1-r712.CSCvp67225
ncs560-os-support-2.1.0.1-r712.CSCvv41516
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .xr
시사민
sysadmin-vm:0_RP0# show install active summary
Active Packages: 4
ncs560-sysadmin-7.1.2 version=7.1.2 [Boot image]
ncs560-sysadmin-ncs560-7.1.2.1-r712.CSCvv41516
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .admin
cisco-klm-rsp4-0.1.p1-r0.0.r712.CSCvt26907 .host
RP에서 FPD 버전 확인
RP/0/RP0/CPU0:ios#show hw-module fpd
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA NEED UPGD 0.53 0.53
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP0 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/RP1 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA NEED UPGD 0.53 0.53
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP1 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
두 RP의 TAM 영역 확인(섹션 제거 평가)
TAM 영역이 손상되지 않았는지 확인하는 것이 중요합니다. 그렇지 않으면 IOFPGA, FPD 업그레이드 및 후속 재로드로 인해 RMA가 발생할 수 있습니다. 이 MOP에서는 FPD 버전 0.64 이상이 사용 중이므로 이 IOFPGA FPD 업그레이드 프로세스 및 RP 다시 로드가 TAM 손상 복구로 이어집니다.
RP0
sysadmin-vm:0_RP0# show control-driver info location 0/RP0
...
Card view from local RP:
TAM Memory is not corrupted
Can proceed with IOFPGA upgrade if required
...
RP1
sysadmin-vm:0_RP0# show control-driver info location 0/RP1
...
Card view from local RP:
TAM Memory is not corrupted
Can proceed with IOFPGA upgrade if required
...
참고: TAM 메모리가 손상된 경우 대상 IOFPGA 버전이 0.64 이상이면 문제가 되지 않습니다.
손상된 TAM 메모리의 샘플 출력
sysadmin-vm:0_RP1# show control-driver info location 0/RP0
<snip>
Card view from local RP:
TAM Memory is corrupted
Do not proceed with IOFPGA upgrade
<snip>
참고: 이 문서에 언급된 모든 전제 조건이 충족되면 업그레이드를 진행할 수 있습니다. "Do not proceed with IOFPGA upgrade(IOFPGA 업그레이드 진행 안 함)"는 0.64 이전 버전의 IOFPGA를 의미합니다.
두 RP에서 IOFPGA 업그레이드 수행
RP/0/RP0/CPU0:ios#upgrade hw-module location all fpd IOFPGA
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP0/CPU0:RONALDO-RF2a#0/RP0/ADMIN0:Oct 16 15:19:26.609 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 IOFPGA FALSE
0/RP0/ADMIN0:Oct 16 15:19:26.610 CEST: fpdserv[4356]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 IOFPGA FALSE
다음을 확인합니다.
RP/0/RP0/CPU0:ios#show hw-module fpd
Fri Oct 16 15:22:11.256 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA RLOAD REQ 0.53 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP0 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/RP1 N560-RSP4-E 0.0 ADM NEED UPGD 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA RLOAD REQ 0.53 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS NEED UPGD 0.15 0.15
0/RP1 N560-RSP4-E 0.0 SATA NEED UPGD 1.30 1.30
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
IOFPGA 업그레이드에 대한 활성 및 대기 RP를 다시 로드하여 완료
먼저 대기 RP를 다시 로드합니다.
sysadmin-vm:0_RP0# hw-module location 0/RP1 reload
Reload hardware module ? [no,yes] yes
이중화가 복원된 후 활성 RP(RP0)를 다시 로드합니다(장애 조치가 트리거됨).
sysadmin-vm:0_RP0# hw-module location 0/RP0 reload
Reload hardware module ? [no,yes] yes
ADM 버전 확인
새 활성 RP(RP1)에서:
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.2
Bootloader Version : 0.0.9
Config Version : 1.4
새 대기 RP(RP0)에서:
[sysadmin-vm:0_RP0:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.2
Bootloader Version : 0.0.9
Config Version : 1.4
두 RP에서 다른 FPD 업그레이드 수행
1. ADM
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPd ADM
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 15:57:14.332 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 ADM FALSE
0/RP1/ADMIN0:Oct 16 15:57:14.333 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 ADM FALSE
2. BIOS
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPD PRIMARY-BIOS
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 PRIMARY-BIOS FALSE
0/RP1/ADMIN0:Oct 16 16:00:29.257 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 PRIMARY-BIOS FALSE
3. SATA
RP/0/RP1/CPU0:ios#upgrade hw-module location all FPD SATA
upgrade command issued (use "show hw-module fpd" to check upgrade status)
RP/0/RP1/CPU0:RONALDO-RF2a#0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Upgrade for the following FPDs has been committed:
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : Location FPD name Force
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : ==================================================
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP1 SATA FALSE
0/RP1/ADMIN0:Oct 16 16:02:06.472 CEST: fpdserv[4503]: %INFRA-FPD_Manager-1-UPGRADE_ALERT : 0/RP0 SATA FALSE
업그레이드 확인
RP/0/RP1/CPU0:ios#show hw-module fpd
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM RLOAD REQ 1.04 1.04
0/RP0 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS RLOAD REQ 0.15 0.16
0/RP0 N560-RSP4-E 0.0 SATA RLOAD REQ 1.30 2.10
0/RP1 N560-RSP4-E 0.0 ADM RLOAD REQ 1.04 1.04
0/RP1 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS RLOAD REQ 0.15 0.16
0/RP1 N560-RSP4-E 0.0 SATA RLOAD REQ 1.30 2.10
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
다른 FPD 업그레이드를 완료하기 위한 전원 주기 절차
참고: ADM 펌웨어 버전이 1.14.2인 경우 다시 로드 스크립트를 사용하기 전에 모든 VM/호스트의 모든 파일 시스템을 동기화해야 합니다.
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.1 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.4 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.4 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.1 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.4.1 chvrf 0 ssh 10.0.2.2 sync
[sysadmin-vm:0_RP1:~]$chvrf 0 ssh 192.0.0.1 chvrf 0 ssh 10.0.2.2 sync
참고: 이러한 명령에 대한 출력이 없습니다.
섀시를 다시 로드하려면
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/reboot_system.sh
Initiating power-cycle of 0/RP0
Initiating power-cycle of 0/RP1
참고: ADM 펌웨어 버전이 1.14.3인 경우 RP의 FPD를 다시 로드해야 합니다.
먼저 대기 RP(RP0)를 다시 로드합니다.
sysadmin-vm:0_RP1# hw-module location 0/RP0 reload
Reload hardware module ? [no,yes] yes
이중화가 복원된 후 활성 RP(RP1)를 다시 로드합니다(장애 조치가 트리거됨).
sysadmin-vm:0_RP1# hw-module location 0/RP1 reload
Reload hardware module ? [no,yes] yes
FPD 버전 확인
RP/0/RP0/CPU0:ios#show hw-module fpd
Fri Oct 16 16:24:18.849 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/5 A900-IMA8Z 0.0 IMFPGA NEED UPGD 17.02 17.02
0/14 A900-IMA8CS1Z-M 0.0 IMFPGA CURRENT 1.95 1.95
0/RP0 N560-RSP4-E 0.0 ADM CURRENT 1.06 1.06
0/RP0 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP0 N560-RSP4-E 0.0 PRIMARY-BIOS CURRENT 0.16 0.16
0/RP0 N560-RSP4-E 0.0 SATA CURRENT 2.10 2.10
0/RP1 N560-RSP4-E 0.0 ADM CURRENT 1.06 1.06
0/RP1 N560-RSP4-E 0.0 IOFPGA CURRENT 0.64 0.64
0/RP1 N560-RSP4-E 0.0 PRIMARY-BIOS CURRENT 0.16 0.16
0/RP1 N560-RSP4-E 0.0 SATA CURRENT 2.10 2.10
0/FT0 A907-FAN-E 1.0 PSOC CURRENT 1.65 1.65
ADM 버전 확인
[sysadmin-vm:0_RP0:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.3
Bootloader Version : 0.0.9
Config Version : 1.6
[sysadmin-vm:0_RP1:~]$/opt/cisco/calvados/sbin/show_adm_version.sh
ADM 1266 Version info
Firmware Version : 1.14.3
Bootloader Version : 0.0.9
Config Version : 1.6
다른 위치의 다른 FPD 업그레이드(있는 경우)
RP/0/RP0/CPU0:ios#upgrade hw-module location 0/5 FPD IMFPGA
Fri Oct 16 16:28:15.006 CEST
upgrade command issued (use "show hw-module fpd" to check upgrade status)