正常なインストレーションを確認するための CLI コマンド
概要
Cisco SCE8000 GBE プラットフォームの設置が完了したら、いくつかの CLI コマンドを実行して、適切なコンポーネントが正しく設置されていて動作可能なことを確認することを推奨します。
基本的なインストレーション後のチェックリスト
次の表は、基本的なインストレーション後のチェックリストと関連する CLI コマンドを示しています。システム設定をさらに確認する方法は、特定のトポロジとインストレーションの設定によって異なりますが、このリストでは、基本的なインストレーションが動作しているかどうかを確認します。
コマンド出力の例については、各コマンドの説明を参照してください。出力内の関連する情報は、 太字 で示しています。
|
|
|
バージョン |
「show version」 |
次のことをチェックします。 • ファームウェアのバージョン • アプリケーションのバージョン • 管理エージェントのステータス • 管理エージェントのバージョン |
光モジュール |
「show inventory」 |
SCE プラットフォームの物理コンポーネントでは、設置した光モジュールがインターフェイスでサポートされることを確認します。 |
ポート設定 |
「show interface」 |
すべてのポートのステータスと設定のリストを取得するには、各ポートに対してこのコマンドを実行します。 |
動作ステータス |
「show system operational status」 |
ステータスは operational である必要があります。 このコマンドは、電源の障害や外部バイパスが正しく設定されていないなどの問題を示します。 |
ラインカードのステータス |
「show interface linecard」 |
shutdown または silent 以外である必要があります。 |
接続モード |
「show interface linecard connection-mode」 |
接続モードと障害モードの両方が正しく設定されていることを確認します。 |
リンク モード |
「show interface linecard link mode」 |
接続モードが inline の場合、リンク モードは forwarding に設定する必要があります。 |
外部バイパス設定 |
「show interface linecard external-bypass」 |
外部バイパス モジュールが設置されている場合に限り、次のことをチェックします。 • 障害時に設定が アクティブになる こと • デバイス数がリンク数と一致していること |
RDR フォーマッタ |
「show RDR-formatter」 |
次のことを確認します。 • RDR フォーマッタが設定された送信先との接続を確立している。 • 複数の送信先がある場合、冗長ステータスが正しく設定されている。 |
Subscriber Manager への接続 |
「show interface linecard subscriber sm-connection-failure」 |
Subscriber Manager(SM)を使用している場合:SM との接続が確立していることを確認します。 |
Quota Manager への接続 |
「show ip rpc-adapter sessions」 |
Quota Manager(QM)を使用している場合:QM との接続が確立していることを確認します。 |
SM および QM を使用して、すべてが搭載されている SCE8000 GBE プラットフォームのコマンド シーケンスを実行します。
SCE> enable 5
Password:<cisco>
SCE> show version
SCE> show inventory
SCE> show interface GigabitEthernet 3/0/0
SCE> show interface GigabitEthernet 3/0/1
SCE> show interface GigabitEthernet 3/0/2
SCE> show interface GigabitEthernet 3/03
SCE> show interface GigabitEthernet 3/0/4
SCE> show interface GigabitEthernet 3/0/5
SCE> show interface GigabitEthernet 3/0/6
SCE> show interface GigabitEthernet 3/0/7
SCE> show interface GigabitEthernet 3/1/0
SCE> show interface GigabitEthernet 3/1/1
SCE> show interface GigabitEthernet 3/1/2
SCE> show interface GigabitEthernet 3/1/3
SCE> show interface GigabitEthernet 3/1/4
SCE> show interface GigabitEthernet 3/1/5
SCE> show interface GigabitEthernet 3/1/6
SCE> show interface GigabitEthernet 3/1/7
SCE> show system operation-status
SCE> show interface linecard 0
SCE> show interface linecard 0 connection-mode
SCE> show interface linecard 0 link mode
SCE> show interface linecard 0 external-bypass
SCE> show rdr-formatter
SCE> show interface linecard 0 subscriber sm-connection-failure
SCE> show ip rpc-adapter sessions
CLI のコマンド出力例
次の出力例で 太字 になっているテキストは、インストレーション後のチェック時にチェックする必要のある行を示しています。いくつかのコマンドでは、出力が短く、出力全体をチェックする必要があります。このような場合は、太字になっていません。
show version
次の行を確認します。
•
System version
•
Application file
•
Management agent interface version
System version: Version 3.5.5 Build 252
Build time: May 31 2009, 15:50:44 (Change-list 483168)
Software version is: Version 3.5.5 Build 252
kernel : [kernel] 2.3.0/1 (inactive: [kernel] 2.3.0/1)
u-boot : [uboot] 2.1.0/1 (field: [uboot] 0.8.1/13)
select : [ubs-cf0] 2.3.0/1 (secondary: [ubs-cf0] 2.3.0/1)
part-num : 73-10598-01 36
cpu (eeprom): 2.1, 1000MHz
cf : Model=SMART CF, S/N=20080213025D41EC41EC, FwRev=0x20060811, Size=4062240KB
cpu (eeprom): 2.1, 1500MHz
cpu (eeprom): 2.1, 1500MHz
part-num : 73-10947-01 22
Part number : 73-10598-01 36
LineCard S/N : CAT1151G012
SML Application information is:
Application file: /apps/data/scos/app/en355262.sli
Application name: Engage SML Version 3.5.5 build 74
Using Lib - Classifier_3.5.5_b74
Application help: Entry point of Engage
Original source file: /auto/srbu-proj1/apps/users/atukh/autoBuild/App/SML/Engage/dev/src/com/pcube/AppTemplate/Main/template_app_main.san
Compilation date: Tue, May 19, 2009 at 19:51:58
Compiler version: SANc v3.20 Build 12 built on: Tue 02/01/2009 11:11:05.;SME plugin v1.1
Capacity option used: 'EngageDefaultSCE8000'.
Management agent interface version: SCE Agent 3.5.5 Build 121
Software package file: ftp://ftpserver/D:\pcube\Os\3.5.5\252\simba_03550252_K9.pkg
SCE8000 uptime is 4 days, 21 hours, 40 minutes, 37 seconds
show inventory
次の行を確認します。
•
テキスト「NAME: "SCE8000 optic」を含むすべての行。搭載されている光モジュールごとに 1 行あります。
NAME: "SCE8000 Chassis", DESCR: "SCE8000"
PID: SCE8000 , VID: V01, SN: FOX1235GP98
NAME: "SCE8000 Service Control Module (SCM) in slot 1", DESCR: """"
PID: "" , VID: "" , SN: CAT1151G012
NAME: "SCE8000 SPA Interface Processor (SIP) in slot 3", DESCR: """"
PID: "" , VID: "" , SN: CAT1150G075
NAME: "SCE8000 SPA module 3/0", DESCR: "SPA-8X1GE-V2"
PID: SPA-8X1GE-V2 , VID: V02, SN: JAE13020GQ5
NAME: "SCE8000 SPA module 3/1", DESCR: "SPA-8X1GE-V2"
PID: SPA-8X1GE-V2 , VID: V02, SN: JAE13020GN3
NAME: "SCE8000 SPA module 3/2", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE114967LE
NAME: "SCE8000 SPA module 3/3", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE11485LCX
NAME: "SCE8000 FAN 1", DESCR: "SCE8000-FAN"
PID: SCE8000-FAN , VID: V01, SN: DCH12130763
NAME: "SCE8000 AC power supply 1", DESCR: "PWR-2700-AC/4"
PID: PWR-2700-AC/4 , VID: V02, SN: APS1216006R
NAME: "SCE8000 AC power supply 2", DESCR: "PWR-2700-AC/4"
PID: PWR-2700-AC/4 , VID: V02, SN: APS12160070
NAME: "SCE8000 optic 3/0/0", DESCR: "N/A "
PID: N/A , VID: "" , SN: FNS0853G1T5
NAME: "SCE8000 optic 3/0/1", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WHD
NAME: "SCE8000 optic 3/0/2", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WF5
NAME: "SCE8000 optic 3/0/3", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WF9
NAME: "SCE8000 optic 3/0/4", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WDT
NAME: "SCE8000 optic 3/0/5", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WE7
NAME: "SCE8000 optic 3/0/6", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WDY
NAME: "SCE8000 optic 3/0/7", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12320WF1
NAME: "SCE8000 optic 3/1/0", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12330A8J
NAME: "SCE8000 optic 3/1/1", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12330A80
NAME: "SCE8000 optic 3/1/2", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12330A7R
NAME: "SCE8000 optic 3/1/3", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS12330A92
NAME: "SCE8000 optic 3/1/4", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS124615JN
NAME: "SCE8000 optic 3/1/5", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS124615K9
NAME: "SCE8000 optic 3/1/6", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS124702V5
NAME: "SCE8000 optic 3/1/7", DESCR: "SFP-GE-S "
PID: SFP-GE-S , VID: V01, SN: FNS1247026J
NAME: "SCE8000 optic 3/2/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ONT1102108E
NAME: "SCE8000 optic 3/3/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL11030105
show interface
各インターフェイスに対してこのコマンドを実行します。コマンド構文は次のとおりです。
show interface GigabitEthernet 3/bay-number/port-number
sce> show interface GigabitEthernet 3/0/0
Auto negotiation configured: Disabled
Auto negotiation: Disabled
Bandwidth (L1): 10000000 Kbps, Burst-size: 50000 bytes
Pseudo IP Address: Not Configured
show system operational status
sce> show system operation-status
System Operation status is Operational
show interface linecard
sce> show interface LineCard 0
The application assigned to slot 0 is /apps/data/scos/app/en355262.sli
Configured shutdown is off
Shutdown due to sm-connection-failure is off
Resulting current shutdown state is off
show interface linecard connection-mode
sce> show interface linecard 0 connection-mode
Connection mode is inline
slot failure mode is external-bypass
Redundancy status is standalone
show interface linecard link mode
sce> show interface linecard 0 link mode
Current link mode is : crosspath-bypass
Actual link mode on active is : forwarding
Actual link mode on failure is: crosspath-bypass
show interface linecard external-bypass
sce1> show interface linecard 0 external-bypass
External bypass current state is 'not activated'.
External bypass failure state is 'activated'.
Amount of expected external bypass devices: 4 (automatically configured).
Amount of detected external bypass devices: 4
show RDR-formatter
次を確認します。
•
Forwarding mode
•
Status(Connection Table の Status カラム)
Forwarding mode: redundancy
--------------------------------------------------------------------------------
| Collector | Port |Status| Priority per Category: |
| IP-Address / | | |------------------------------------------------|
| Host-Name | | | Category1 | Category2 | Category3 | Category4 |
|---------------|-------|------|-----------|------------|-----------|-----------|
| 10.240.59.39 | 33000 | up |100 primary| --- | --- | --- |
| 10.240.59.44 | 33000 | up | --- |100 primary | --- | --- |
---------------------------------------------------------------------------------
RDR: queued: 0 ,sent:60108106, thrown: 0, format-mismatch: 0
UM: queued: 0 ,sent: 0, thrown: 0
Logger: queued: 0 ,sent: 0, thrown: 0
Last time these counters were cleared: 07:36:52 EDT TUE April 28 2009
show interface linecard subscriber sm-connection-failure
Subscriber Manager で作業している場合は、このコマンドを使用して SM との接続が確立されていることを確認します。
SCE> show interface linecard 0 subscriber sm-connection-failure
Current SM link state: up.
Configured action to take when SM link is down: No action.
Changing of system operational-status to 'warning' when SM link is down: enabled.
show ip rpc-adapter sessions
Quota Manager で作業している場合は、このコマンドを使用して QM との接続が確立されていることを確認します。
sce> show ip rpc-adapter sessions
client-name=usr.SM
client-address=/10.240.59.36
started=Mon Apr 06 12:43:01 GMT-04:00 2009
received-message-num=408790
dropped-notifications-num=0
client-address=/10.240.59.36
started=Mon Apr 06 12:43:02 GMT-04:00 2009
received-message-num=5715112
sent-notifications-num=386768
dropped-notifications-num=0
client-name=mcn.QuotaManager-10.248.64.119_10.240.59.36_SCE.J.API.PRPC
client-address=/10.240.59.36
started=Mon Apr 06 12:43:03 GMT-04:00 2009
received-message-num=404194
dropped-notifications-num=0