dépannage d'un scénario lié aux schémas Bulkstats et solutions de contournement recommandées dans StarOS

Introduction

Ce document décrit un scénario lié à l'ajout et la suppression de schémas Bulkstat dans StarOS ainsi que les problèmes et les solutions recommandées pour ces problèmes.

Conditions préalables

Exigences

Cisco vous recommande de prendre connaissance des rubriques suivantes :

• Linux
• StarOS
  
  

Cisco recommande que vous disposiez d'un accès privilégié :

• mode caché pour exécuter le shell de débogage afin d'accéder à l'invite de commande du shell linux
• Accès SFTP (Secure File Transfer Protocol) au noeud StarOS

Composants utilisés

Les informations contenues dans ce document sont basées sur la version 21.16.6.77063 de StarOS.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. Si votre réseau est en ligne, assurez-vous de bien comprendre l’incidence possible des commandes.

Informations générales

1. Pour configurer un fichier de configuration afin de stocker les configurations liées à bulkstats.
2. Le format de la commande est le suivant :

        configure

               [no] bulkstats config [ schema | supplement ] <url>

        end

Where:

• Le mot clé facultatif schema vous permet de remplacer uniquement le schéma à l'aide du fichier fourni et de conserver la configuration du serveur.
• Le mot-clé facultatif supplément vous permet de compléter la configuration Bulkstats en cours avec le contenu du fichier de configuration fourni. Ces mots-clés ne fonctionnent que sur les fichiers existants.
• URL indique l'emplacement du fichier de configuration bulkstats.

Problème

Impossible d'ajouter de nouveaux schémas/de rajouter le schéma actuel (s'il est supprimé) via l'invite de commande CLI.

Scénarios de test

1. Problème rencontré en raison de l’utilisation du schéma <URL> cli bulkstat config.
2. Il s'agit d'un résultat attendu par conception lorsqu'un schéma de mot clé facultatif est utilisé.
3. Le même scénario a été testé en laboratoire. Voici les résultats :
   Scénario A. Initialement, l’interface de ligne de commande bulkstat config <url> a été configurée.

[local]MME# show configuration bulkstats

config

  bulkstats collection

  bulkstats historical collection

  bulkstats config /hd-raid/file1

  bulkstats mode

    file 1

      header format Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

      footer format EndOfFile

      card schema cardSch1 format PPM,card,cardSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpubusy%,%cpuidle%,%numproc%,%memused%,%memtotal%,%numcpu%,%cpu0-cpubusy%,%cpu0-cpuidle%,%cpu0-numproc%,%cpu0-memused%,%cpu0-memtotal%,%cpu0-name%,%cpu0-cpuused-user%,%cpu0-cpuused-sys%,%cpu0-cpuused-io%,%cpu0-cpuused-irq%,%cpu0-cpuused-idle%,%cpu1-cpubusy%,%cpu1-cpuidle%,%cpu1-numproc%,

      card schema cardSch2 format PPM,card,cardSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpu1-memused%,%cpu1-memtotal%,%cpu1-name%,%cpu1-cpuused-user%,%cpu1-cpuused-sys%,%cpu1-cpuused-io%,%cpu1-cpuused-irq%,%cpu1-cpuused-idle%,%cpu2-cpubusy%,%cpu2-cpuidle%,%cpu2-numproc%,%cpu2-memused%,%cpu2-memtotal%,%cpu2-name%,%cpu2-cpuused-user%,%cpu2-cpuused-sys%,%cpu2-cpuused-io%,%cpu2-cpuused-irq%,%cpu2-cpuused-idle%,%cpu3-cpubusy%,%cpu3-cpuidle%,

      card schema cardSch3 format PPM,card,cardSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpu3-numproc%,%cpu3-memused%,%cpu3-memtotal%,%cpu3-name%,%cpu3-cpuused-user%,%cpu3-cpuused-sys%,%cpu3-cpuused-io%,%cpu3-cpuused-irq%,%cpu3-cpuused-idle%,%15avg-cpubusy%,%15peak-cpubusy%,%5avg-cpubusy%,%5peak-cpubusy%,%1avg-cpubusy%,%15avg-memused%,%15peak-memused%,%5avg-memused%,%5peak-memused%,%1avg-memused%,%cpu0-15avg-cpubusy%,%cpu0-15peak-cpubusy%,

      port schema portSch1 format PPM,port,portSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%port%,%maxrate%,%rxbytes%,%txbytes%,%ucast_inpackets%,%ucast_outpackets%,%mcast_inpackets%,%mcast_outpackets%,%bcast_inpackets%,%bcast_outpackets%,%rxpackets%,%txpackets%,%rxdiscbytes%,%rxdiscpackets%,%txdiscbytes%,%txdiscpackets%,%rxerrorbytes%,%rxerrorpackets%,%txerrorbytes%,%txerrorpackets%,

      port schema portSch2 format PPM,port,portSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%port%,%frag-rcvd%,%pkt-reassembled%,%frag-tokernel%,%util-rx-curr%,%util-tx-curr%,%util-rx-5min%,%util-tx-5min%,%util-rx-15min%,%util-tx-15min%,%port-5peak-rx-util%,%port-5peak-tx-util%,%port-15peak-rx-util%,%port-15peak-tx-util%,

      apn-expansion schema apn1 format PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

      apn-expansion schema apn2 format PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

      apn-expansion schema apn3 format PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

    #exit

  #exit

end


[local]MME# show bulkstats schemas

Bulk Statistics Server Configuration:

  Server State:                  Enabled

  File Limit:                    7500 KB

  Sample Interval:               15 minutes (0D 0H 15M)

  Transfer Interval:             480 minutes (0D 8H 0M)

  Receiver Mode:                 Secondary-on-failure

  Historical Data Collection:    Enabled (15 samples stored)




Bulk Statistics Server Statistics:

  Records awaiting transmission: 0

  Bytes awaiting transmission:   0

  Total records collected:       0

  Total bytes collected:         0

  Total records transmitted:     0

  Total bytes transmitted:       0

  Total records discarded:       0

  Total bytes discarded:         0

  Last collection time required: 0 second(s)

  Last transfer time required:   0 second(s)

  No successful data transfers

  No attempted data transfers




  File 1

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 2 not configured




  File 3 not configured




  File 4 not configured




------------------- Schemas for File 1----------------------------------------

Type         Name                     Active-Only Format

------------ ------------------------ ----------- ----------------------------------------

card         cardSch1                 No          PPM,card,cardSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpubusy%,%cpuidle%,%numproc%,%memused%,%memtotal%,%numcpu%,%cpu0-cpubusy%,%cpu0-cpuidle%,%cpu0-numproc%,%cpu0-memused%,%cpu0-memtotal%,%cpu0-name%,%cpu0-cpuused-user%,%cpu0-cpuused-sys%,%cpu0-cpuused-io%,%cpu0-cpuused-irq%,%cpu0-cpuused-idle%,%cpu1-cpubusy%,%cpu1-cpuidle%,%cpu1-numproc%,

card         cardSch2                 No          PPM,card,cardSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpu1-memused%,%cpu1-memtotal%,%cpu1-name%,%cpu1-cpuused-user%,%cpu1-cpuused-sys%,%cpu1-cpuused-io%,%cpu1-cpuused-irq%,%cpu1-cpuused-idle%,%cpu2-cpubusy%,%cpu2-cpuidle%,%cpu2-numproc%,%cpu2-memused%,%cpu2-memtotal%,%cpu2-name%,%cpu2-cpuused-user%,%cpu2-cpuused-sys%,%cpu2-cpuused-io%,%cpu2-cpuused-irq%,%cpu2-cpuused-idle%,%cpu3-cpubusy%,%cpu3-cpuidle%,

card         cardSch3                 No          PPM,card,cardSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%cpu3-numproc%,%cpu3-memused%,%cpu3-memtotal%,%cpu3-name%,%cpu3-cpuused-user%,%cpu3-cpuused-sys%,%cpu3-cpuused-io%,%cpu3-cpuused-irq%,%cpu3-cpuused-idle%,%15avg-cpubusy%,%15peak-cpubusy%,%5avg-cpubusy%,%5peak-cpubusy%,%1avg-cpubusy%,%15avg-memused%,%15peak-memused%,%5avg-memused%,%5peak-memused%,%1avg-memused%,%cpu0-15avg-cpubusy%,%cpu0-15peak-cpubusy%,

port         portSch1                 No          PPM,port,portSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%port%,%maxrate%,%rxbytes%,%txbytes%,%ucast_inpackets%,%ucast_outpackets%,%mcast_inpackets%,%mcast_outpackets%,%bcast_inpackets%,%bcast_outpackets%,%rxpackets%,%txpackets%,%rxdiscbytes%,%rxdiscpackets%,%txdiscbytes%,%txdiscpackets%,%rxerrorbytes%,%rxerrorpackets%,%txerrorbytes%,%txerrorpackets%,

port         portSch2                 No          PPM,port,portSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%card%,%port%,%frag-rcvd%,%pkt-reassembled%,%frag-tokernel%,%util-rx-curr%,%util-tx-curr%,%util-rx-5min%,%util-tx-5min%,%util-rx-15min%,%util-tx-15min%,%port-5peak-rx-util%,%port-5peak-tx-util%,%port-15peak-rx-util%,%port-15peak-tx-util%,

apn-expansion apn1                     No          PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

apn-expansion apn2                     No          PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

apn-expansion apn3                     No          PPM,apn-expansion,%epochtime%,%localdate%,%localtime%,

mon-di-net   mdn1                     No          PPM,%epochtime%,%localdate%,%localtime%,

[local]MME#

Scénario B. Pour ajouter le schéma de mots-clés facultatif, vous devez d'abord supprimer l'interface de ligne de commande bulkstat en configurant no bulkstats. Au moment où vous exécutez no bulkstats config, tous les schémas actuels dans le noeud sont supprimés.                 

[local]MME#

[local]MME# configure

[local]MME(config)# bulkstats collection

[local]MME(config)# no bulkstats config

<cr>                 - newline         

[local]MME(config)# no bulkstats config

[local]MME(config)# end

[local]MME# show configuration bulkstats

config

  bulkstats collection

  bulkstats historical collection

  bulkstats mode

    file 1

      header format Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

      footer format EndOfFile

    #exit

  #exit

end

[local]MME# show bulkstats schemas

Bulk Statistics Server Configuration:

  Server State:                  Enabled

  File Limit:                    7500 KB

  Sample Interval:               15 minutes (0D 0H 15M)

  Transfer Interval:             480 minutes (0D 8H 0M)

  Receiver Mode:                 Secondary-on-failure

  Historical Data Collection:    Enabled (15 samples stored)




Bulk Statistics Server Statistics:

  Records awaiting transmission: 0

  Bytes awaiting transmission:   0

  Total records collected:       0

  Total bytes collected:         0

  Total records transmitted:     0

  Total bytes transmitted:       0

  Total records discarded:       0

  Total bytes discarded:         0

  Last collection time required: 0 second(s)

  Last transfer time required:   0 second(s)

  No successful data transfers

  No attempted data transfers




  File 1

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 2 not configured




  File 3 not configured




  File 4 not configured

[local]MME#

[local]MME# 

Scénario C. Ensuite, l'interface bulkstat config schema <url> est configuré. Toutes les configurations et tous les schémas présents dans le fichier de configuration sont ajoutés au noeud.

[local]MME# configure

[local]MME(config)# bulkstats collection

[local]MME(config)# bulkstats config schema /hd-raid/file2

Info: config

Info: bulkstats mode

Info: file 2

Info: header format Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

Info: footer format EndOfFile

Info: diameter-auth schema diameter-authSch1 format PPM,diameter-auth,diameter-authSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%servertype%,%group%,%der-req-id-sent%,%der-req-aka-chal-sent%,%der-req-retried%,%dea-chal-rcvd%,%dea-acpt-rcvd%,%dea-timeout%,%dea-badauth%,%dea-malformed%,%dea-malformed-avp%,%dea-dropped%,%rar-req-rcvd%,%raa-ans-accpt-sent%,%aar-req-sent%,%str-req-sent%,%str-req-retried%,

Info: diameter-auth schema diameter-authSch2 format PPM,diameter-auth,diameter-authSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%sta-ans-accpt-rcvd%,%asr-req-rcvd%,%asa-rsp-accpt-sent%,%asa-rsp-rej-sent%,%req-sock-write-err%,%rsp-sock-write-err%,%any-sock-read-err%,%rem-disconnect%,%loc-disconnect%,

Info: diameter-auth schema diameter-authSch3 format PPM,diameter-auth,diameter-authSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%peer%,%diameter-auth-msg-multiround%,%diameter-auth-msg-success%,%diameter-auth-msg-err-protocol%,%diameter-auth-msg-err-transient%,%diameter-auth-msg-err-permanent%,%diameter-auth-msg-err-other%,%aaa-req-received%,%aaa-req-timeouts%,%aaa-req-dropped%,

Info: schema systemSch1 format PPM,system,systemSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-ttlarrived%,%sess-ttlrejected%,%sess-ttlconnected%,%sess-ttlfailed%,%sess-ttldisconn%,%sess-ttlhandoff%,%sess-ttlrenewal%,%sess-ttlcallop%,%sess-ttlauthsucc%,%sess-ttlauthfail%,%sess-curaaaactive%,%sess-curaaadeleting%,%sess-curaaaacctpending%,%sess-curaaaacctitemsused%,%sess-curaaaacctitemsmax%,%sess-curaaabuffused%,%sess-curaaabuffmax%,%sess-ttlaaacancauth%,%sess-ttlaaaacctpurged%,%sess-ttlradacctpurged%,%sess-ttllcpup%,

Info: schema systemSch10 format PPM,system,systemSch10,%epochtime%,%localdate%,%localtime%,%uptime%,%aaa-ttlpseudoauthreq%,%aaa-curpseudoauthreq%,%aaa-ttlauthnulluser%,%aaa-ttlacctsucc%,%aaa-ttlacctpurged%,%aaa-ttlacctcancelled%,%aaa-ttlacctkeepalivesuccess%,%aaa-ttlacctkeepalivetimeout%,%aaa-ttlacctkeepalivepurged%,%aaa-ttlradacctreq%,%aaa-ttlradacctcancelled%,%aaa-ttlradacctpurged%,%aaa-ttlradacctreqretried%,%aaa-ttlradacctrspdropped%,%aaa-ttlmgrpurgedrequests%,%diamauth-msg-mareq%,%diamauth-msg-maans%,%diamauth-msg-marretry%,%diamauth-msg-maatimeout%,%diamauth-msg-maadropped%,%diamauth-msg-sareq%,

Info: schema systemSch100 format PPM,system,systemSch100,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-bearerdur-24hr-qci6%,%sess-bearerdur-over24hr-qci6%,%sess-bearerdur-2day-qci6%,%sess-bearerdur-4day-qci6%,%sess-bearerdur-5day-qci6%,%sess-bearerdur-5sec-qci7%,%sess-bearerdur-10sec-qci7%,%sess-bearerdur-30sec-qci7%,%sess-bearerdur-1min-qci7%,%sess-bearerdur-2min-qci7%,%sess-bearerdur-5min-qci7%,%sess-bearerdur-15min-qci7%,%sess-bearerdur-30min-qci7%,%sess-bearerdur-1hr-qci7%,%sess-bearerdur-4hr-qci7%,%sess-bearerdur-12hr-qci7%,%sess-bearerdur-24hr-qci7%,%sess-bearerdur-over24hr-qci7%,%sess-bearerdur-2day-qci7%,%sess-bearerdur-4day-qci7%,%sess-bearerdur-5day-qci7%,

Info: sgs schema sgsSch1 format PPM,sgs,sgsSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%pag-req-tx%,%pag-req-retx%,%pag-req-rx%,%pag-rej-tx%,%pag-rej-retx%,%pag-rej-rx%,%service-req-tx%,%service-req-retx%,%service-req-rx%,%dl-ud-tx%,%dl-ud-retx%,%dl-ud-rx%,%ul-ud-tx%,%ul-ud-retx%,%ul-ud-rx%,%localupd-req-tx%,%localupd-req-retx%,

Info: sgs schema sgsSch2 format PPM,sgs,sgsSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%localupd-req-rx%,%localupd-accept-tx%,%localupd-accept-retx%,%localupd-accept-rx%,%localupd-rej-tx%,%localupd-rej-retx%,%localupd-rej-rx%,%tmsi-reloc-tx%,%tmsi-reloc-retx%,%tmsi-reloc-rx%,%alert-req-tx%,%alert-req-retx%,%alert-req-rx%,%alert-ack-tx%,%alert-ack-retx%,%alert-ack-rx%,%alert-rej-tx%,%alert-rej-retx%,%alert-rej-rx%,%ue-actind-tx%,%ue-actind-retx%,

Info: sgs schema sgsSch3 format PPM,sgs,sgsSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%ue-actind-rx%,%eps-detind-tx%,%eps-detind-retx%,%eps-detind-rx%,%eps-detack-tx%,%eps-detack-retx%,%eps-detack-rx%,%imsi-detind-tx%,%imsi-detind-retx%,%imsi-detind-rx%,%imsi-detack-tx%,%imsi-detack-retx%,%imsi-detack-rx%,,,,,,,%mm-inforeq-tx%,%mm-inforeq-retx%,

Info: exit

[local]MME(config)# end

[local]MME#

[local]MME# show configuration bulkstats

config

  bulkstats collection

  bulkstats historical collection

  bulkstats config schema /hd-raid/file2

  bulkstats mode

    file 1

      header format Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

      footer format EndOfFile

    #exit

    file 2

      header format Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

      footer format EndOfFile

      schema systemSch1 format PPM,system,systemSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-ttlarrived%,%sess-ttlrejected%,%sess-ttlconnected%,%sess-ttlfailed%,%sess-ttldisconn%,%sess-ttlhandoff%,%sess-ttlrenewal%,%sess-ttlcallop%,%sess-ttlauthsucc%,%sess-ttlauthfail%,%sess-curaaaactive%,%sess-curaaadeleting%,%sess-curaaaacctpending%,%sess-curaaaacctitemsused%,%sess-curaaaacctitemsmax%,%sess-curaaabuffused%,%sess-curaaabuffmax%,%sess-ttlaaacancauth%,%sess-ttlaaaacctpurged%,%sess-ttlradacctpurged%,%sess-ttllcpup%,

      schema systemSch10 format PPM,system,systemSch10,%epochtime%,%localdate%,%localtime%,%uptime%,%aaa-ttlpseudoauthreq%,%aaa-curpseudoauthreq%,%aaa-ttlauthnulluser%,%aaa-ttlacctsucc%,%aaa-ttlacctpurged%,%aaa-ttlacctcancelled%,%aaa-ttlacctkeepalivesuccess%,%aaa-ttlacctkeepalivetimeout%,%aaa-ttlacctkeepalivepurged%,%aaa-ttlradacctreq%,%aaa-ttlradacctcancelled%,%aaa-ttlradacctpurged%,%aaa-ttlradacctreqretried%,%aaa-ttlradacctrspdropped%,%aaa-ttlmgrpurgedrequests%,%diamauth-msg-mareq%,%diamauth-msg-maans%,%diamauth-msg-marretry%,%diamauth-msg-maatimeout%,%diamauth-msg-maadropped%,%diamauth-msg-sareq%,

      schema systemSch100 format PPM,system,systemSch100,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-bearerdur-24hr-qci6%,%sess-bearerdur-over24hr-qci6%,%sess-bearerdur-2day-qci6%,%sess-bearerdur-4day-qci6%,%sess-bearerdur-5day-qci6%,%sess-bearerdur-5sec-qci7%,%sess-bearerdur-10sec-qci7%,%sess-bearerdur-30sec-qci7%,%sess-bearerdur-1min-qci7%,%sess-bearerdur-2min-qci7%,%sess-bearerdur-5min-qci7%,%sess-bearerdur-15min-qci7%,%sess-bearerdur-30min-qci7%,%sess-bearerdur-1hr-qci7%,%sess-bearerdur-4hr-qci7%,%sess-bearerdur-12hr-qci7%,%sess-bearerdur-24hr-qci7%,%sess-bearerdur-over24hr-qci7%,%sess-bearerdur-2day-qci7%,%sess-bearerdur-4day-qci7%,%sess-bearerdur-5day-qci7%,

      diameter-auth schema diameter-authSch1 format PPM,diameter-auth,diameter-authSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%servertype%,%group%,%der-req-id-sent%,%der-req-aka-chal-sent%,%der-req-retried%,%dea-chal-rcvd%,%dea-acpt-rcvd%,%dea-timeout%,%dea-badauth%,%dea-malformed%,%dea-malformed-avp%,%dea-dropped%,%rar-req-rcvd%,%raa-ans-accpt-sent%,%aar-req-sent%,%str-req-sent%,%str-req-retried%,

      diameter-auth schema diameter-authSch2 format PPM,diameter-auth,diameter-authSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%sta-ans-accpt-rcvd%,%asr-req-rcvd%,%asa-rsp-accpt-sent%,%asa-rsp-rej-sent%,%req-sock-write-err%,%rsp-sock-write-err%,%any-sock-read-err%,%rem-disconnect%,%loc-disconnect%,

      diameter-auth schema diameter-authSch3 format PPM,diameter-auth,diameter-authSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%peer%,%diameter-auth-msg-multiround%,%diameter-auth-msg-success%,%diameter-auth-msg-err-protocol%,%diameter-auth-msg-err-transient%,%diameter-auth-msg-err-permanent%,%diameter-auth-msg-err-other%,%aaa-req-received%,%aaa-req-timeouts%,%aaa-req-dropped%,

      sgs schema sgsSch1 format PPM,sgs,sgsSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%pag-req-tx%,%pag-req-retx%,%pag-req-rx%,%pag-rej-tx%,%pag-rej-retx%,%pag-rej-rx%,%service-req-tx%,%service-req-retx%,%service-req-rx%,%dl-ud-tx%,%dl-ud-retx%,%dl-ud-rx%,%ul-ud-tx%,%ul-ud-retx%,%ul-ud-rx%,%localupd-req-tx%,%localupd-req-retx%,

      sgs schema sgsSch2 format PPM,sgs,sgsSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%localupd-req-rx%,%localupd-accept-tx%,%localupd-accept-retx%,%localupd-accept-rx%,%localupd-rej-tx%,%localupd-rej-retx%,%localupd-rej-rx%,%tmsi-reloc-tx%,%tmsi-reloc-retx%,%tmsi-reloc-rx%,%alert-req-tx%,%alert-req-retx%,%alert-req-rx%,%alert-ack-tx%,%alert-ack-retx%,%alert-ack-rx%,%alert-rej-tx%,%alert-rej-retx%,%alert-rej-rx%,%ue-actind-tx%,%ue-actind-retx%,

      sgs schema sgsSch3 format PPM,sgs,sgsSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%ue-actind-rx%,%eps-detind-tx%,%eps-detind-retx%,%eps-detind-rx%,%eps-detack-tx%,%eps-detack-retx%,%eps-detack-rx%,%imsi-detind-tx%,%imsi-detind-retx%,%imsi-detind-rx%,%imsi-detack-tx%,%imsi-detack-retx%,%imsi-detack-rx%,,,,,,,%mm-inforeq-tx%,%mm-inforeq-retx%,

    #exit

  #exit

end

[local]MME#

Scénario D. Après cela, il n'est plus possible d'ajouter de nouveaux schémas. Lorsque vous essayez de supprimer un schéma actuel et de le rajouter, le schéma est supprimé mais vous ne pourrez pas le rajouter. Cependant, le schéma actuel était toujours présent dans le fichier de configuration (fichier de configuration présent dans l'URL).

[local]MME# configure

[local]MME(config)# bulkstats mode




mode                 - Enters bulk statistics configuration mode, where you can define what statistics to collect      

[local]MME(config)# bulkstats mode

[local]MME(config-bulkstats)# file 1

[local]MME(config-bulkstats-file-1)# mon-di-net schema mdn1 format PPM,%epochti

me%,%localdate%,%localtime%,

[local]MME(config-bulkstats-file-1)# exit

[local]MME(config-bulkstats)# file 2

[local]MME(config-bulkstats-file-2)# mon-di-net schema mdn2 format PPM,%epochti

me%,

[local]MME(config-bulkstats-file-2)# end

[local]MME# show bulkstats schemas

Bulk Statistics Server Configuration:

  Server State:                  Enabled

  File Limit:                    7500 KB

  Sample Interval:               15 minutes (0D 0H 15M)

  Transfer Interval:             480 minutes (0D 8H 0M)

  Receiver Mode:                 Secondary-on-failure

  Historical Data Collection:    Enabled (15 samples stored)




Bulk Statistics Server Statistics:

  Records awaiting transmission: 0

  Bytes awaiting transmission:   0

  Total records collected:       0

  Total bytes collected:         0

  Total records transmitted:     0

  Total bytes transmitted:       0

  Total records discarded:       0

  Total bytes discarded:         0

  Last collection time required: 0 second(s)

  Last transfer time required:   0 second(s)

  No successful data transfers

  No attempted data transfers




  File 1

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 2

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 3 not configured




  File 4 not configured




------------------- Schemas for File 2----------------------------------------

Type         Name                     Active-Only Format

------------ ------------------------ ----------- ----------------------------------------

system       systemSch1               No          PPM,system,systemSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-ttlarrived%,%sess-ttlrejected%,%sess-ttlconnected%,%sess-ttlfailed%,%sess-ttldisconn%,%sess-ttlhandoff%,%sess-ttlrenewal%,%sess-ttlcallop%,%sess-ttlauthsucc%,%sess-ttlauthfail%,%sess-curaaaactive%,%sess-curaaadeleting%,%sess-curaaaacctpending%,%sess-curaaaacctitemsused%,%sess-curaaaacctitemsmax%,%sess-curaaabuffused%,%sess-curaaabuffmax%,%sess-ttlaaacancauth%,%sess-ttlaaaacctpurged%,%sess-ttlradacctpurged%,%sess-ttllcpup%,

system       systemSch10              No          PPM,system,systemSch10,%epochtime%,%localdate%,%localtime%,%uptime%,%aaa-ttlpseudoauthreq%,%aaa-curpseudoauthreq%,%aaa-ttlauthnulluser%,%aaa-ttlacctsucc%,%aaa-ttlacctpurged%,%aaa-ttlacctcancelled%,%aaa-ttlacctkeepalivesuccess%,%aaa-ttlacctkeepalivetimeout%,%aaa-ttlacctkeepalivepurged%,%aaa-ttlradacctreq%,%aaa-ttlradacctcancelled%,%aaa-ttlradacctpurged%,%aaa-ttlradacctreqretried%,%aaa-ttlradacctrspdropped%,%aaa-ttlmgrpurgedrequests%,%diamauth-msg-mareq%,%diamauth-msg-maans%,%diamauth-msg-marretry%,%diamauth-msg-maatimeout%,%diamauth-msg-maadropped%,%diamauth-msg-sareq%,

system       systemSch100             No          PPM,system,systemSch100,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-bearerdur-24hr-qci6%,%sess-bearerdur-over24hr-qci6%,%sess-bearerdur-2day-qci6%,%sess-bearerdur-4day-qci6%,%sess-bearerdur-5day-qci6%,%sess-bearerdur-5sec-qci7%,%sess-bearerdur-10sec-qci7%,%sess-bearerdur-30sec-qci7%,%sess-bearerdur-1min-qci7%,%sess-bearerdur-2min-qci7%,%sess-bearerdur-5min-qci7%,%sess-bearerdur-15min-qci7%,%sess-bearerdur-30min-qci7%,%sess-bearerdur-1hr-qci7%,%sess-bearerdur-4hr-qci7%,%sess-bearerdur-12hr-qci7%,%sess-bearerdur-24hr-qci7%,%sess-bearerdur-over24hr-qci7%,%sess-bearerdur-2day-qci7%,%sess-bearerdur-4day-qci7%,%sess-bearerdur-5day-qci7%,

diameter-auth diameter-authSch1        No          PPM,diameter-auth,diameter-authSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%servertype%,%group%,%der-req-id-sent%,%der-req-aka-chal-sent%,%der-req-retried%,%dea-chal-rcvd%,%dea-acpt-rcvd%,%dea-timeout%,%dea-badauth%,%dea-malformed%,%dea-malformed-avp%,%dea-dropped%,%rar-req-rcvd%,%raa-ans-accpt-sent%,%aar-req-sent%,%str-req-sent%,%str-req-retried%,

diameter-auth diameter-authSch2        No          PPM,diameter-auth,diameter-authSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%sta-ans-accpt-rcvd%,%asr-req-rcvd%,%asa-rsp-accpt-sent%,%asa-rsp-rej-sent%,%req-sock-write-err%,%rsp-sock-write-err%,%any-sock-read-err%,%rem-disconnect%,%loc-disconnect%,

diameter-auth diameter-authSch3        No          PPM,diameter-auth,diameter-authSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%peer%,%diameter-auth-msg-multiround%,%diameter-auth-msg-success%,%diameter-auth-msg-err-protocol%,%diameter-auth-msg-err-transient%,%diameter-auth-msg-err-permanent%,%diameter-auth-msg-err-other%,%aaa-req-received%,%aaa-req-timeouts%,%aaa-req-dropped%,

sgs          sgsSch1                  No          PPM,sgs,sgsSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%pag-req-tx%,%pag-req-retx%,%pag-req-rx%,%pag-rej-tx%,%pag-rej-retx%,%pag-rej-rx%,%service-req-tx%,%service-req-retx%,%service-req-rx%,%dl-ud-tx%,%dl-ud-retx%,%dl-ud-rx%,%ul-ud-tx%,%ul-ud-retx%,%ul-ud-rx%,%localupd-req-tx%,%localupd-req-retx%,

sgs          sgsSch2                  No          PPM,sgs,sgsSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%localupd-req-rx%,%localupd-accept-tx%,%localupd-accept-retx%,%localupd-accept-rx%,%localupd-rej-tx%,%localupd-rej-retx%,%localupd-rej-rx%,%tmsi-reloc-tx%,%tmsi-reloc-retx%,%tmsi-reloc-rx%,%alert-req-tx%,%alert-req-retx%,%alert-req-rx%,%alert-ack-tx%,%alert-ack-retx%,%alert-ack-rx%,%alert-rej-tx%,%alert-rej-retx%,%alert-rej-rx%,%ue-actind-tx%,%ue-actind-retx%,

sgs          sgsSch3                  No          PPM,sgs,sgsSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%ue-actind-rx%,%eps-detind-tx%,%eps-detind-retx%,%eps-detind-rx%,%eps-detack-tx%,%eps-detack-retx%,%eps-detack-rx%,%imsi-detind-tx%,%imsi-detind-retx%,%imsi-detind-rx%,%imsi-detack-tx%,%imsi-detack-retx%,%imsi-detack-rx%,,,,,,,%mm-inforeq-tx%,%mm-inforeq-retx%,

[local]MME# configure

[local]MME(config)# bulkstats mode

[local]MME(config-bulkstats)# file 2

[local]MME(config-bulkstats-file-2)# no sgs

sgs                  - Removes sgs bulk statistics schema  

[local]MME(config-bulkstats-file-2)# no sgs schema sgsSch1

[local]MME(config-bulkstats-file-2)# end

[local]MME# show bulkstats schemas

Bulk Statistics Server Configuration:

  Server State:                  Enabled

  File Limit:                    7500 KB

  Sample Interval:               15 minutes (0D 0H 15M)

  Transfer Interval:             480 minutes (0D 8H 0M)

  Receiver Mode:                 Secondary-on-failure

  Historical Data Collection:    Enabled (15 samples stored)




Bulk Statistics Server Statistics:

  Records awaiting transmission: 0

  Bytes awaiting transmission:   0

  Total records collected:       0

  Total bytes collected:         0

  Total records transmitted:     0

  Total bytes transmitted:       0

  Total records discarded:       0

  Total bytes discarded:         0

  Last collection time required: 0 second(s)

  Last transfer time required:   0 second(s)

  No successful data transfers

  No attempted data transfers




  File 1

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 2

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 3 not configured




  File 4 not configured




------------------- Schemas for File 2----------------------------------------

Type         Name                     Active-Only Format

------------ ------------------------ ----------- ----------------------------------------

system       systemSch1               No          PPM,system,systemSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-ttlarrived%,%sess-ttlrejected%,%sess-ttlconnected%,%sess-ttlfailed%,%sess-ttldisconn%,%sess-ttlhandoff%,%sess-ttlrenewal%,%sess-ttlcallop%,%sess-ttlauthsucc%,%sess-ttlauthfail%,%sess-curaaaactive%,%sess-curaaadeleting%,%sess-curaaaacctpending%,%sess-curaaaacctitemsused%,%sess-curaaaacctitemsmax%,%sess-curaaabuffused%,%sess-curaaabuffmax%,%sess-ttlaaacancauth%,%sess-ttlaaaacctpurged%,%sess-ttlradacctpurged%,%sess-ttllcpup%,

system       systemSch10              No          PPM,system,systemSch10,%epochtime%,%localdate%,%localtime%,%uptime%,%aaa-ttlpseudoauthreq%,%aaa-curpseudoauthreq%,%aaa-ttlauthnulluser%,%aaa-ttlacctsucc%,%aaa-ttlacctpurged%,%aaa-ttlacctcancelled%,%aaa-ttlacctkeepalivesuccess%,%aaa-ttlacctkeepalivetimeout%,%aaa-ttlacctkeepalivepurged%,%aaa-ttlradacctreq%,%aaa-ttlradacctcancelled%,%aaa-ttlradacctpurged%,%aaa-ttlradacctreqretried%,%aaa-ttlradacctrspdropped%,%aaa-ttlmgrpurgedrequests%,%diamauth-msg-mareq%,%diamauth-msg-maans%,%diamauth-msg-marretry%,%diamauth-msg-maatimeout%,%diamauth-msg-maadropped%,%diamauth-msg-sareq%,

system       systemSch100             No          PPM,system,systemSch100,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-bearerdur-24hr-qci6%,%sess-bearerdur-over24hr-qci6%,%sess-bearerdur-2day-qci6%,%sess-bearerdur-4day-qci6%,%sess-bearerdur-5day-qci6%,%sess-bearerdur-5sec-qci7%,%sess-bearerdur-10sec-qci7%,%sess-bearerdur-30sec-qci7%,%sess-bearerdur-1min-qci7%,%sess-bearerdur-2min-qci7%,%sess-bearerdur-5min-qci7%,%sess-bearerdur-15min-qci7%,%sess-bearerdur-30min-qci7%,%sess-bearerdur-1hr-qci7%,%sess-bearerdur-4hr-qci7%,%sess-bearerdur-12hr-qci7%,%sess-bearerdur-24hr-qci7%,%sess-bearerdur-over24hr-qci7%,%sess-bearerdur-2day-qci7%,%sess-bearerdur-4day-qci7%,%sess-bearerdur-5day-qci7%,

diameter-auth diameter-authSch1        No          PPM,diameter-auth,diameter-authSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%servertype%,%group%,%der-req-id-sent%,%der-req-aka-chal-sent%,%der-req-retried%,%dea-chal-rcvd%,%dea-acpt-rcvd%,%dea-timeout%,%dea-badauth%,%dea-malformed%,%dea-malformed-avp%,%dea-dropped%,%rar-req-rcvd%,%raa-ans-accpt-sent%,%aar-req-sent%,%str-req-sent%,%str-req-retried%,

diameter-auth diameter-authSch2        No          PPM,diameter-auth,diameter-authSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%sta-ans-accpt-rcvd%,%asr-req-rcvd%,%asa-rsp-accpt-sent%,%asa-rsp-rej-sent%,%req-sock-write-err%,%rsp-sock-write-err%,%any-sock-read-err%,%rem-disconnect%,%loc-disconnect%,

diameter-auth diameter-authSch3        No          PPM,diameter-auth,diameter-authSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%peer%,%diameter-auth-msg-multiround%,%diameter-auth-msg-success%,%diameter-auth-msg-err-protocol%,%diameter-auth-msg-err-transient%,%diameter-auth-msg-err-permanent%,%diameter-auth-msg-err-other%,%aaa-req-received%,%aaa-req-timeouts%,%aaa-req-dropped%,

sgs          sgsSch2                  No          PPM,sgs,sgsSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%localupd-req-rx%,%localupd-accept-tx%,%localupd-accept-retx%,%localupd-accept-rx%,%localupd-rej-tx%,%localupd-rej-retx%,%localupd-rej-rx%,%tmsi-reloc-tx%,%tmsi-reloc-retx%,%tmsi-reloc-rx%,%alert-req-tx%,%alert-req-retx%,%alert-req-rx%,%alert-ack-tx%,%alert-ack-retx%,%alert-ack-rx%,%alert-rej-tx%,%alert-rej-retx%,%alert-rej-rx%,%ue-actind-tx%,%ue-actind-retx%,

sgs          sgsSch3                  No          PPM,sgs,sgsSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%ue-actind-rx%,%eps-detind-tx%,%eps-detind-retx%,%eps-detind-rx%,%eps-detack-tx%,%eps-detack-retx%,%eps-detack-rx%,%imsi-detind-tx%,%imsi-detind-retx%,%imsi-detind-rx%,%imsi-detack-tx%,%imsi-detack-retx%,%imsi-detack-rx%,,,,,,,%mm-inforeq-tx%,%mm-inforeq-retx%,

[local]MME# configure

[local]MME(config)# bulkstats mode

[local]MME(config-bulkstats)# file 2

[local]MME(config-bulkstats-file-2)# sgs schema sgsSch1 format PPM,sgs,sgsSch1,

%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%serv

id%,%pag-req-tx%,%pag-req-retx%,%pag-req-rx%,%pag-rej-tx%,%pag-rej-retx%,%pag-r

ej-rx%,%service-req-tx%,%service-req-retx%,%service-req-rx%,%dl-ud-tx%,%dl-ud-r

etx%,%dl-ud-rx%,%ul-ud-tx%,%ul-ud-retx%,%ul-ud-rx%,%localupd-req-tx%,%localupd-

req-retx%,

[local]MME(config-bulkstats-file-2)# end

[local]MME# show bulkstats schemas

Bulk Statistics Server Configuration:

  Server State:                  Enabled

  File Limit:                    7500 KB

  Sample Interval:               15 minutes (0D 0H 15M)

  Transfer Interval:             480 minutes (0D 8H 0M)

  Receiver Mode:                 Secondary-on-failure

  Historical Data Collection:    Enabled (15 samples stored)




Bulk Statistics Server Statistics:

  Records awaiting transmission: 0

  Bytes awaiting transmission:   0

  Total records collected:       0

  Total bytes collected:         0

  Total records transmitted:     0

  Total bytes transmitted:       0

  Total records discarded:       0

  Total bytes discarded:         0

  Last collection time required: 0 second(s)

  Last transfer time required:   0 second(s)

  No successful data transfers

  No attempted data transfers




  File 1

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 2

    Remote File Format:            %date%-%time%

    File Header:                   Version-20.0,%ipaddr%,%date%-%time%,%localdate%-%localtime%,%localtz%,%localtzoffset%,%localdate3%-%localtime3%,%swbuild%

    File Footer:                   EndOfFile

    No bulkstats receivers

    File Statistics:

      Records awaiting transmission: 0

      Bytes awaiting transmission:   0

      Total records collected:       0

      Total bytes collected:         0

      Total records transmitted:     0

      Total bytes transmitted:       0

      Total records discarded:       0

      Total bytes discarded:         0

      Last transfer time required:   0 second(s)

      No successful data transfers

      No attempted data transfers




  File 3 not configured




  File 4 not configured




------------------- Schemas for File 2----------------------------------------

Type         Name                     Active-Only Format

------------ ------------------------ ----------- ----------------------------------------

system       systemSch1               No          PPM,system,systemSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-ttlarrived%,%sess-ttlrejected%,%sess-ttlconnected%,%sess-ttlfailed%,%sess-ttldisconn%,%sess-ttlhandoff%,%sess-ttlrenewal%,%sess-ttlcallop%,%sess-ttlauthsucc%,%sess-ttlauthfail%,%sess-curaaaactive%,%sess-curaaadeleting%,%sess-curaaaacctpending%,%sess-curaaaacctitemsused%,%sess-curaaaacctitemsmax%,%sess-curaaabuffused%,%sess-curaaabuffmax%,%sess-ttlaaacancauth%,%sess-ttlaaaacctpurged%,%sess-ttlradacctpurged%,%sess-ttllcpup%,

system       systemSch10              No          PPM,system,systemSch10,%epochtime%,%localdate%,%localtime%,%uptime%,%aaa-ttlpseudoauthreq%,%aaa-curpseudoauthreq%,%aaa-ttlauthnulluser%,%aaa-ttlacctsucc%,%aaa-ttlacctpurged%,%aaa-ttlacctcancelled%,%aaa-ttlacctkeepalivesuccess%,%aaa-ttlacctkeepalivetimeout%,%aaa-ttlacctkeepalivepurged%,%aaa-ttlradacctreq%,%aaa-ttlradacctcancelled%,%aaa-ttlradacctpurged%,%aaa-ttlradacctreqretried%,%aaa-ttlradacctrspdropped%,%aaa-ttlmgrpurgedrequests%,%diamauth-msg-mareq%,%diamauth-msg-maans%,%diamauth-msg-marretry%,%diamauth-msg-maatimeout%,%diamauth-msg-maadropped%,%diamauth-msg-sareq%,

system       systemSch100             No          PPM,system,systemSch100,%epochtime%,%localdate%,%localtime%,%uptime%,%sess-bearerdur-24hr-qci6%,%sess-bearerdur-over24hr-qci6%,%sess-bearerdur-2day-qci6%,%sess-bearerdur-4day-qci6%,%sess-bearerdur-5day-qci6%,%sess-bearerdur-5sec-qci7%,%sess-bearerdur-10sec-qci7%,%sess-bearerdur-30sec-qci7%,%sess-bearerdur-1min-qci7%,%sess-bearerdur-2min-qci7%,%sess-bearerdur-5min-qci7%,%sess-bearerdur-15min-qci7%,%sess-bearerdur-30min-qci7%,%sess-bearerdur-1hr-qci7%,%sess-bearerdur-4hr-qci7%,%sess-bearerdur-12hr-qci7%,%sess-bearerdur-24hr-qci7%,%sess-bearerdur-over24hr-qci7%,%sess-bearerdur-2day-qci7%,%sess-bearerdur-4day-qci7%,%sess-bearerdur-5day-qci7%,

diameter-auth diameter-authSch1        No          PPM,diameter-auth,diameter-authSch1,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%servertype%,%group%,%der-req-id-sent%,%der-req-aka-chal-sent%,%der-req-retried%,%dea-chal-rcvd%,%dea-acpt-rcvd%,%dea-timeout%,%dea-badauth%,%dea-malformed%,%dea-malformed-avp%,%dea-dropped%,%rar-req-rcvd%,%raa-ans-accpt-sent%,%aar-req-sent%,%str-req-sent%,%str-req-retried%,

diameter-auth diameter-authSch2        No          PPM,diameter-auth,diameter-authSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%sta-ans-accpt-rcvd%,%asr-req-rcvd%,%asa-rsp-accpt-sent%,%asa-rsp-rej-sent%,%req-sock-write-err%,%rsp-sock-write-err%,%any-sock-read-err%,%rem-disconnect%,%loc-disconnect%,

diameter-auth diameter-authSch3        No          PPM,diameter-auth,diameter-authSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnid%,%vpnname%,%ipaddr%,%port%,%peer%,%diameter-auth-msg-multiround%,%diameter-auth-msg-success%,%diameter-auth-msg-err-protocol%,%diameter-auth-msg-err-transient%,%diameter-auth-msg-err-permanent%,%diameter-auth-msg-err-other%,%aaa-req-received%,%aaa-req-timeouts%,%aaa-req-dropped%,

sgs          sgsSch2                  No          PPM,sgs,sgsSch2,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%localupd-req-rx%,%localupd-accept-tx%,%localupd-accept-retx%,%localupd-accept-rx%,%localupd-rej-tx%,%localupd-rej-retx%,%localupd-rej-rx%,%tmsi-reloc-tx%,%tmsi-reloc-retx%,%tmsi-reloc-rx%,%alert-req-tx%,%alert-req-retx%,%alert-req-rx%,%alert-ack-tx%,%alert-ack-retx%,%alert-ack-rx%,%alert-rej-tx%,%alert-rej-retx%,%alert-rej-rx%,%ue-actind-tx%,%ue-actind-retx%,

sgs          sgsSch3                  No          PPM,sgs,sgsSch3,%epochtime%,%localdate%,%localtime%,%uptime%,%vpnname%,%vpnid%,%servname%,%servid%,%ue-actind-rx%,%eps-detind-tx%,%eps-detind-retx%,%eps-detind-rx%,%eps-detack-tx%,%eps-detack-retx%,%eps-detack-rx%,%imsi-detind-tx%,%imsi-detind-retx%,%imsi-detind-rx%,%imsi-detack-tx%,%imsi-detack-retx%,%imsi-detack-rx%,,,,,,,%mm-inforeq-tx%,%mm-inforeq-retx%,

[local]MME#

Scénario E. Ainsi, le résultat est chaque fois que vous utilisez le mot clé facultatif schème, vous ne pouvez pas ajouter de nouveaux schémas. Vous pouvez supprimer tous les schémas actuels (du noeud), mais vous ne pouvez pas les rajouter. Cependant, les schémas actuels présents dans le fichier de configuration (qui est présent dans <url>, ne sont pas affectés par les modifications effectuées dans le noeud).

Solution

1. Le schéma de configuration <url> cli bulkstat est utilisé, en raison duquel il a rencontré ce problème.
2. Il s'agit d'un résultat attendu par conception, que vous obtenez si le schéma de mot clé facultatif est utilisé.
3. Il existe trois solutions pour ce cas, à savoir :

R.Pour supprimer le schéma de configuration cli bulkstat <url> et contrôler l’ajout/la suppression de schémas via une invite de commande/cli manuelle.

B. Pour utiliser le mot clé facultatif supplément dans l’interface de ligne de commande de configuration bulkstat. Avec le supplément de configuration cli bulkstat <url>, vous pouvez ajouter les schémas présents dans le fichier de configuration aux schémas du noeud actuel. Vous pouvez ajouter/supprimer de nouveaux schémas et les schémas actuels peuvent également être supprimés/rajoutés via l'invite de commande CLI.    

C. Pour ajouter/supprimer les schémas requis directement dans le fichier de configuration, puis recharger les configurations avec le fichier de configuration (supprimez d’abord l’interface de ligne de commande par no bulkstat config, ajoutez les schémas dans le fichier de configuration, puis rajoutez-les par bulkstats config schema <url>). Pour ajouter les schémas dans le fichier de configuration, vous pouvez soit le faire avec l'éditeur vi, soit le faire par SFTP

Avec l'éditeur vi :

[local]MME-01# cli test-commands password <pswd>
Warning: Test commands enables internal testing and debugging commands
USE OF THIS MODE MAY CAUSE SIGNIFICANT SERVICE INTERRUPTION

[local]MME-01# debug shell 
Last log in: Wed Dec 22 15:05:12 +0530 2021 on pts/3 from 10.227.224.108.
MME-01:card1-cpu0# ls -lrtha

total 16
-r--r--r-- 1 root root 952 Dec 15 23:30 .rhosts
-r--r--r-- 1 root root 1.7K Dec 15 23:30 .gdbinit
drwx------ 2 root root 100 Dec 15 23:30 .ssh
drwxr-xr-x 24 root root 500 Dec 15 23:30 ..
-rw------- 1 root root 118 Dec 21 14:48 .bash_history
-rw-r--r-- 1 root root 1 Dec 22 15:05 file
drwxr-xr-x 3 root root 140 Dec 22 15:05 .

MME-01:card1-cpu0# vi file

Envoyez le fichier de configuration par SFTP de l’<url> vers votre lecteur local, modifiez-le et envoyez-le par SFTP vers l’<url>.