Introduction
Ce document décrit la procédure de configuration et de vérification initiale pour configurer le commutateur Catalyst 9600.
Conditions préalables
Conditions requises
Cisco vous recommande de prendre connaissance des rubriques suivantes :
Vérifiez que le châssis et le superviseur sont installés conformément aux guides d'installation.
Components Used
Les informations contenues dans ce document sont basées et configurées sur les versions logicielles et matérielles suivantes :
- Matériel : Commutateur Catalyst 9600
- le logiciel Cisco IOS: Cisco IOS® XE 16.12.3a
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. Si votre réseau est en ligne, assurez-vous de bien comprendre l’incidence possible des commandes.
Informations générales
Vous pouvez démarrer, configurer et vérifier Catalyst 9600 en trois étapes.
Se lever
- Connexion de la console
- Mise sous tension du système
- Observer les messages de console
- Sélectionner l'option de boîte de dialogue de configuration
Configuration
- Gestion des périphériques
- Nom de l'hôte
- Horloge
- Enregistrez la configuration
Vérification
- Version du logiciel et package
- Matériel système, alimentation, etc.
- Connectivité IP de gestion
- Santé du système
- Heure
|
|
Se lever
- Connexion du PC à la console du Catalyst 9600 avec RJ45 ou USB
- Mise sous tension du système
- Observer la console imprime l'initialisation matérielle du système et d'autres informations à l'écran
Démarrage initial :
Initializing Hardware...
Initializing Hardware......
System Bootstrap, Version 17.3.1r[FC2], RELEASE SOFTWARE (P)
Compiled 30-04-2020 12:00:00.00 by rel
Current ROMMON image : Primary Rommon Image
Last reset cause:LocalSoft
C9600-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
boot: attempting to boot from [bootflash:packages.conf]
boot: reading file packages.conf
<truncated
###########################################################################
<truncated>
Base Ethernet MAC Address : 6c:b2:ae:4a:70:c0
Motherboard Assembly Number : 4C57
Motherboard Serial Number : FXS230103TN
Model Revision Number : V02
Motherboard Revision Number : 3
Model Number : C9606R
System Serial Number : FXS2302Q2EP
Attendez que la boîte de dialogue Configuration du système s'affiche. Sélectionnez l'option Non afin de passer en mode de configuration manuelle et sélectionnez Oui afin de terminer l'installation automatique, pour accéder à la configuration manuelle simple.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Would you like to terminate autoinstall? [yes]: yes
Press RETURN to get started
*Nov 5 15:40:26.909: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Nov 5 15:40:26.909: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Configuration
Note: Utilisez la commande show running-config à tout moment en mode « enable » pour vérifier les valeurs configurées.
Configurez le port de gestion avec une adresse IP de votre réseau et activez le port.
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface gigabitEthernet 0/0
Switch(config-if)#ip address 10.122.186.8 255.255.255.240
Switch(config-if)#no shutdown
Configurez une route statique afin d'atteindre le réseau Default Gateway for Management, utilisez votre adresse IP et votre passerelle réseau.
Switch(config)#ip route vrf Mgmt-vrf 10.122.157.250 255.255.255.255 10.122.186.1
Configurez Line VTY, Virtual Terminal afin d'accéder via telnet et définissez un mot de passe de votre choix.
Switch(config)#line vty 0 4
Switch(config-line)#password cisco
Switch(config-line)#login
Transport input all autorise tous les protocoles (ex. ssh, telnet) afin d'accéder au périphérique via des sessions VTY.
Switch(config-line)#transport input all
Switch(config-line)#exit
Configurez le mot de passe du mode utilisateur pour l'accès à la console.
Switch(config)#line console 0
Switch(config-line)#password cisco
Switch(config-line)#login
Switch(config-line)#exit
Configurez un mot de passe en mode enable fort.
Switch(config)#enable secret cisco
Réglez l'horloge système.
Switch(config)#clock timezone utc +5 30
*Nov 6 04:34:58.910: %SYS-6-CLOCKUPDATE: System clock has been updated from 10:05:58 utc Fri Nov 6 2020 to 10:04:58 utc Fri Nov 6 2020, configured from console by console.
*Nov 6 04:35:59.634: %SYS-5-CONFIG_I: Configured from console by console
Switch#clock set 04:30:00 6 Nov 2020
*Nov 5 23:00:00.000: %SYS-6-CLOCKUPDATE: System clock has been updated from 10:06:19 utc Fri Nov 6 2020 to 04:30:00 utc Fri Nov 6 2020, configured from console by console.
Nov 5 23:00:00.000: %PKI-6-AUTHORITATIVE_CLOCK: The system clock has been set.
Configurez le nom d'hôte du système.
Switch(config)#hostname Catalyst-9600
Enregistrez la configuration configurée jusqu’à présent dans la configuration de démarrage.
Catalyst-9600#write memory
Building configuration...
[OK]
*Nov 5 16:11:46.061: %SYS-2-PRIVCFG_ENCRYPT: Successfully encrypted private config file
Vérification
Vérifiez la version du logiciel sur le système, observez le temps de fonctionnement, les détails du système, etc.
Catalyst-9600#show version
Cisco IOS XE Software, Version 16.12.03a
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.12.3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 28-Apr-20 09:37 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2020 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: System Bootstrap, Version 17.3.1r[FC2], RELEASE SOFTWARE (P)
Catalyst-9600 uptime is 36 minutes
Uptime for this control processor is 37 minutes
System returned to ROM by Reload Command
System image file is "bootflash:packages.conf"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
------------------------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------------
network-advantage Smart License network-advantage
dna-advantage Subscription Smart License dna-advantage
AIR License Level: AIR DNA Advantage
Next reload AIR license Level: AIR DNA Advantage
Smart Licensing Status: UNREGISTERED/EVAL MODE
cisco C9606R (X86) processor (revision V00) with 1867991K/6147K bytes of memory.
Processor board ID FXS2302Q2EP
1 Virtual Ethernet interface
24 Forty/Hundred Gigabit Ethernet interfaces
48 TwentyFive Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
16009160K bytes of physical memory.
11161600K bytes of Bootflash at bootflash:.
1638400K bytes of Crash Files at crashinfo:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : 6c:b2:ae:4a:70:c0
Motherboard Assembly Number : 4C57
Motherboard Serial Number : FXS230103TN
Model Revision Number : V02
Motherboard Revision Number : 3
Model Number : C9606R
System Serial Number : FXS2302Q2EP
Configuration register is 0x102
Vérifiez les packages installés.
Catalyst-9600#show install summary
[ R0 R1 ] Installed Package(s) Information:
State (St): I - Inactive, U - Activated & Uncommitted,
C - Activated & Committed, D - Deactivated & Uncommitted
--------------------------------------------------------------------------------
Type St Filename/Version
--------------------------------------------------------------------------------
IMG C 16.12.3a.0.4
--------------------------------------------------------------------------------
Auto abort timer: inactive
--------------------------------------------------------------------------------
Vérifiez la route pour le VRF de gestion.
Switch#show ip route vrf Mgmt-vrf
Routing Table: Mgmt-vrf
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, m - OMP
n - NAT, Ni - NAT inside, No - NAT outside, Nd - NAT DIA
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
H - NHRP, G - NHRP registered, g - NHRP registration summary
o - ODR, P - periodic downloaded static route, l - LISP
a - application route
+ - replicated route, % - next hop override, p - overrides from PfR
Gateway of last resort is not set
S* 0.0.0.0/0 [1/0] via 10.122.186.1 <--- the default gateway
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
S 10.122.157.250/32 [1/0] via 10.122.186.1
C 10.122.186.0/28 is directly connected, GigabitEthernet0/0
L 10.122.186.8/32 is directly connected, GigabitEthernet0/0
Vérifiez l'accessibilité au réseau via la passerelle par défaut.
Switch#ping vrf Mgmg-vrf 10.122.186.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.122.186.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Switch#
Vérifiez les modules installés dans le système.
Catalyst-9600#show module
Chassis Type: C9606R
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+--------------+--------------
1 24 24-Port 40GE/12-Port 100GE C9600-LC-24C CAT2252L0PY
3 0 Supervisor 1 Module C9600-SUP-1 CAT2252L0SH
4 0 Supervisor 1 Module C9600-SUP-1 CAT2252L0SU
6 48 48-Port 10GE / 25GE C9600-LC-48YL CAT2302L16G
Mod MAC addresses Hw Fw Sw Status
---+--------------------------------+----+------------+------------------+--------
1 70B3.175A.7580 to 70B3.175A.75FF 0.10 17.3.1r[FC2] 16.12.03a ok
3 70B3.175A.5680 to 70B3.175A.56FF 0.10 17.3.1r[FC2] 16.12.03a ok
4 70B3.175A.5600 to 70B3.175A.567F 0.10 17.3.1r[FC2] 16.12.03a ok
6 6C8B.D307.6680 to 6C8B.D307.66FF 0.10 17.3.1r[FC2] 16.12.03a ok
Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode
---+-------------------+-------------------------+---------------------------
3 Active sso sso
4 Standby sso sso
Chassis MAC address range: 64 addresses from 6cb2.ae4a.70c0 to 6cb2.ae4a.70ff
Vérifiez l'état du système à l'aide des résultats de test automatique de mise sous tension (POST) et de diagnostic.
Catalyst-9600#show post
Stored system POST messages:
Switch C9606R
--------------
Thu Nov 5 15:34:27 2020 POST: Module: 6 Mac Loopback Begin
Thu Nov 5 15:34:27 2020 POST: Module: 6 Mac Loopback: loopback Test: End, Status Passed
Thu Nov 5 15:34:27 2020 POST: Module: 1 Mac Loopback Begin
Thu Nov 5 15:34:27 2020 POST: Module: 1 Mac Loopback: loopback Test: End, Status Passed
Catalyst-9600#show diagnostic result module all
Current bootup diagnostic level: minimal
module 1: SerialNo : CAT2252L0PY
Overall Diagnostic Result for module 1 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestGoldPktLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
2) TestOBFL ------------------------> U
3) TestThermal ---------------------> .
4) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
U U U U U U U U U . U . U U U U U U U U U U . U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
module 3: SerialNo : CAT2252L0SH
Overall Diagnostic Result for module 3 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestOBFL ------------------------> U
2) TestFantray ---------------------> .
3) TestThermal ---------------------> .
4) TestScratchRegister -------------> .
module 4: SerialNo : CAT2252L0SU
Overall Diagnostic Result for module 4 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestOBFL ------------------------> U
2) TestFantray ---------------------> U
3) TestThermal ---------------------> .
4) TestScratchRegister -------------> U
module 6: SerialNo : CAT2302L16G
Overall Diagnostic Result for module 6 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestGoldPktLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
2) TestOBFL ------------------------> U
3) TestThermal ---------------------> .
4) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . U U U . U . U . . . U U . U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
U U . U U U U U U U U U U U . U . U U U U . . U
Vérifiez si l'horloge est correctement réglée.
Catalyst-9600#show clock
*16:32:55.196 UTC Thu Nov 5 2020
Vérifiez les modules d'alimentation installés et leur état.
Catalyst-9600#show power detail
Power Fan States
Supply Model No Type Capacity Status 1 2
------ -------------------- ---- -------- ------------ -----------
PS1 C9600-PWR-2KWAC ac 2000 W active good good
PS4 C9600-PWR-2KWAC ac 2000 W active good good
PS Current Configuration Mode : none
PS Current Operating State : none
Power supplies currently active : 2
Power supplies currently available : 2
Power Summary Maximum
(in Watts) Used Available
------------- ------ ---------
System Power 2800 3940
------------- ------ ---------
Total 2800 3940
Power Budget Mode : Dual Sup
Power Out of In
Mod Model No State Budget Instantaneous Peak Reset Reset
--- -------------------- -------- ------ ------------- ---- ------ -----
1 C9600-LC-24C accepted 300 0 0 300 10
3 C9600-SUP-1 accepted 950 0 0 950 202
4 C9600-SUP-1 accepted 950 0 0 950 202
6 C9600-LC-48YL accepted 300 0 0 300 10
FM1 C9606-FAN accepted 300 -- -- 300 --
--- -------------------- -------- ------ ------------- ---- ------ -----
Total allocated power: 2800
Total required power: 2800
Informations connexes