Configuration d'un serveur d'accès avec PRI pour les appels asynchrones et RNIS entrants à liaisons multiples

Options de téléchargement

  • PDF     (244.3 KB)
    Consulter à l'aide d'Adobe Reader sur un grand nombre d'appareils
  • ePub     (109.2 KB)
    Consulter à l’aide de différentes applications sur iPhone, iPad, Android ou Windows Phone
  • Mobi (Kindle)     (142.8 KB)
    Consulter sur un appareil Kindle ou à l’aide d’une application Kindle sur plusieurs appareils
Mis à jour:29 janvier 2008
ID du document:6310

Langage exempt de préjugés

Dans le cadre de la documentation associée à ce produit, nous nous efforçons d’utiliser un langage exempt de préjugés. Dans cet ensemble de documents, le langage exempt de discrimination renvoie à une langue qui exclut la discrimination en fonction de l’âge, des handicaps, du genre, de l’appartenance raciale de l’identité ethnique, de l’orientation sexuelle, de la situation socio-économique et de l’intersectionnalité. Des exceptions peuvent s’appliquer dans les documents si le langage est codé en dur dans les interfaces utilisateurs du produit logiciel, si le langage utilisé est basé sur la documentation RFP ou si le langage utilisé provient d’un produit tiers référencé. Découvrez comment Cisco utilise le langage inclusif.

À propos de cette traduction

Cisco a traduit ce document en traduction automatisée vérifiée par une personne dans le cadre d’un service mondial permettant à nos utilisateurs d’obtenir le contenu d’assistance dans leur propre langue. Il convient cependant de noter que même la meilleure traduction automatisée ne sera pas aussi précise que celle fournie par un traducteur professionnel.

Introduction

Dans de nombreux environnements, vous devez configurer un serveur d'accès qui peut accepter les appels entrants des utilisateurs asynchrones et RNIS. Ces utilisateurs peuvent ensuite se connecter au réseau en toute transparence comme s'ils étaient physiquement présents. Une telle configuration est généralement utilisée pour fournir une connectivité réseau aux utilisateurs qui voyagent et sont des télétravailleurs, ainsi qu'aux sites SOHO (Small Office-Home Office).

Ce document décrit comment configurer un serveur d'accès pour accepter les appels asynchrones et RNIS entrants sur les circuits RNIS T1 PRI. La configuration fournit la configuration minimale requise pour que le serveur d'accès au réseau (NAS) accepte l'appel. Vous pouvez ajouter des fonctionnalités supplémentaires à cette configuration en fonction de vos besoins.

Conditions préalables

Conditions requises

Aucune spécification déterminée n'est requise pour ce document.

Components Used

Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :

  • Cisco AS5300 avec 192 modems MICA et huit ports T1 qui exécutent le logiciel Cisco IOS® version 12.2(5).

  • Deux T1 PRI.

  • Un PC qui exécute Microsoft Windows. Ce PC dispose d'un modem analogique et d'une connexion téléphonique au réseau téléphonique du commutateur public. Le PC compose le T1 PRI connecté à l'AS5300.

  • Routeurs des gammes Cisco 800 et 1600 avec circuits RNIS BRI. Ces routeurs sont des clients de numérotation RNIS. La configuration du Cisco 1600 est fournie. Vous pouvez appliquer cette configuration client à n'importe quel routeur doté d'une interface BRI.

  • Authentification, autorisation et comptabilité locales (AAA). Si vous disposez d'un serveur RADIUS AAA ou Tacacs+, vous pouvez utiliser l'un ou l'autre d'entre eux pour fournir AAA pour les appels entrants.

Remarque : La configuration du routeur Cisco 800 est similaire à celle du routeur Cisco 1600 et n'est pas incluse dans ce document.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Produits connexes

Vous pouvez utiliser cette configuration avec n'importe quel routeur doté de cartes T1 ou PRI et de modems numériques internes (par exemple, MICA, NextPort ou Microcom). Tous les routeurs de la gamme AS5xxx dotés d'une carte T1 ou PRI et de modems numériques peuvent utiliser les concepts de cette configuration.

Les routeurs de la gamme Cisco 2600 ne prennent pas en charge les modems numériques internes. Vous pouvez configurer les routeurs de la gamme Cisco 2600 pour qu'ils acceptent uniquement les appels RNIS, à condition que le routeur dispose d'une carte WIC T1 ou PRI ou d'un module réseau.

Les routeurs de la gamme Cisco 3600 peuvent prendre en charge les appels RNIS et Modem. Cependant, les routeurs de la gamme Cisco 3600 nécessitent une carte d'interface WAN ou un module réseau T1 ou PRI et le module réseau de modem numérique NM-xDM.

Vous pouvez également apporter des modifications pour utiliser cette configuration avec les ports E1 ou PRI. Configurez le contrôleur E1 avec les caractéristiques physiques de codage de ligne, de tramage et autres que votre opérateur téléphonique fournit. La configuration du canal D (interface Serial x:15 pour E1) est similaire à celle présentée dans ce document.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Configuration

Cette section vous fournit des informations pour configurer les fonctionnalités décrites dans ce document.

Remarque : Pour en savoir plus sur les commandes utilisées dans le présent document, utilisez l’outil de recherche de commandes (clients inscrits seulement).

Diagramme du réseau

Ce document utilise la configuration réseau suivante :

5300.gif

Configurations

Ce document utilise les configurations suivantes :

maui-nas-02 (5300) 
maui-nas-02#show running-config 
 Building configuration...

 Current configuration : 3671 bytes
 !
 ! No configuration change since last restart
 !
 version 12.2
 service timestamps debug datetime msec
 service timestamps log datetime msec
 service password-encryption
 !
 hostname maui-nas-02
 !
 boot system flash:c5300-i-mz.122-5.bin
 aaa new-model
 aaa authentication login default local
 aaa authentication login NO_AUTHEN none
 aaa authentication ppp default local
 aaa authorization network default local 
 
!--- PPP authentication and network authorization are local. !--- Replace local with radius or tacacs if you use an AAA server.

 enable secret 5 <deleted>
 !
 username admin password 7 <deleted>
 username async_user password 7 <deleted>
 username travis_isdn password 7 <deleted>
 username austin_isdn password 7 <deleted>
 
!--- Usernames for local authentication of the call. !--- The client presents the username/password and the NAS !--- authenticates the peer.

 spe 1/0 1/8
  firmware location mica-modem-pw.2.7.3.0.bin
 spe 2/0 2/7
  firmware location mica-modem-pw.2.7.3.0.bin
 !
 ip subnet-zero
 ip domain-name maui-onions.com
 
!--- Tells the NAS how to qualify DNS lookups. !--- In this example, maui-onions.com is appended to the end of each !--- looked-up name.

 ip name-server 172.22.53.210
 
!--- Specifies the primary name server.

 !
 async-bootp dns-server 172.22.53.210
 
!--- Specifies (for async clients) the IP address of domain name servers. 

 isdn switch-type primary-ni
 
!--- Switch-type for this NAS. Obtain this information from the Telco.

 !
 controller T1 0
 
!--- First T1 PRI

  framing esf
 
!--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco.

  clock source line primary
 
!--- T1 0 is the primary clock source for this NAS. !--- Clock source must be specified for the timing and synchronization !--- of the T1 carrier.

  linecode b8zs
 
!--- Linecoding for this T1. Obtain this information from the Telco.

  pri-group timeslots 1-24
 
!--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as !--- ISDN PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 0:23.

 !
 controller T1 1
 
!--- Second T1 PRI.

  framing esf
 
!--- Framing for this T1 is Extended Super Frame (ESF). !--- Obtain this information from the Telco.

  clock source line secondary 1
 
!--- T1 1 is the first secondary clock source for this NAS. !--- If the primary clock fails, this secondary clock takes over.

  linecode b8zs
 
!--- Linecoding for this T1. Obtain this information from the Telco.

  pri-group timeslots 1-24
 
!--- For T1 PRI scenarios, all 24 T1 timeslots are assigned as ISDN !--- PRI channels. The router now automatically creates the !--- corresponding D-channel: interface Serial 1:23.

 !
 controller T1 2
 
!--- This T1 is unused.

  framing sf
  clock source line secondary 2
  linecode ami
 !
 
!--- Unused interface configuration is omitted here.

 !
 interface Loopback0
  ip address 172.22.60.1 255.255.255.0
 
!--- The IP pool for async users is in this subnet. !--- The routes for all async clients are summarized and !--- propagated to the backbone instead of 254 routes.

 !
 interface Loopback1
  ip address 172.22.61.1 255.255.255.0
 
!--- The IP pool for ISDN users is in this subnet. !--- The routes for all ISDN clients are summarized and !--- propagated to the backbone instead of 254 routes.

 !
 interface Ethernet0
  ip address 172.22.53.140 255.255.255.0
 !         
 
!--- Unused interface configuration is omitted here.

 !
 interface Serial0:23
 
!--- D-channel configuration for T1 0.

  no ip address
  encapsulation ppp

 !--- PPP encapsulation on this interface.

  dialer rotary-group 10
 
!--- T1 0 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10.

  isdn switch-type primary-ni
  isdn incoming-voice modem
 
!--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls.

  no cdp enable
  ppp authentication chap
  ppp multilink
 !
 interface Serial1:23
 
!--- D-channel configuration for T1 1.

  no ip address
  encapsulation ppp
 
!--- PPP encapsulation on this interface.

  dialer rotary-group 10
 
!--- T1 1 is a member of rotary group 10. !--- The rotary group configuration is in interface Dialer 10.

  isdn switch-type primary-ni
  isdn incoming-voice modem
 
!--- All incoming voice calls on this T1 are sent to the modems. !--- This command is required if this T1 is to accept async calls.

  no cdp enable
  ppp authentication chap
  ppp multilink
 !
 interface Group-Async0
 
!--- This group-async interface is the configuration template for all modems. !--- You need not configure individual async interfaces because you can !--- clone the interfaces from one managed copy.

  ip unnumbered Loopback0
 
!--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability.

  encapsulation ppp
  dialer in-band
  dialer idle-timeout 900
  dialer-group 5
 
!--- Interesting traffic is defined in dialer-list 5. !--- Note: The specified dialer-group number must be the same as the !--- dialer-list number. In this example, the number is defined as "5".

  async mode interactive
 
!--- Users can dial in and get to a shell or PPP session on that line. !--- You can use this command in conjunction with autoselect ppp !--- under the line configuration to automatically detect the connection type.

  peer default ip address pool ASYNC
 
!--- Clients are assigned addresses from the IP address pool named ASYNC.

  no fair-queue
  ppp authentication chap
 
!--- Use CHAP authentication.

  ppp multilink
  group-range 1 192
 
!--- Modems 1 through 192 are members of this group async interface.

 !
 interface Dialer10
 
!--- Configuration for rotary group 10. !--- The Dialer interface number (10) must exactly match rotary !--- group number configured on the physical interfaces.

  ip unnumbered Loopback1
 
!--- A Loopback interface is always up/up. So, unnumber the loopback interface !--- for stability.

  encapsulation ppp
  dialer in-band

 !--- Enable V.25bis on this interface.

  dialer idle-timeout 900
 
!--- Idle timeout for incoming calls is 900 seconds (15 mins).

  dialer-group 5
 
!--- Apply interesting traffic definition from dialer-list 5. !--- Note: The specified dialer-group number must be the same !--- as the dialer-list number. !--- In this example, the number is defined as "5".

  peer default ip address pool ISDN
 
!--- Clients are assigned addresses from the IP address pool named ISDN.

  ppp authentication chap
  ppp multilink
 !
 router eigrp 69
  network 172.22.0.0
  auto-summary
  no eigrp log-neighbor-changes
 !
 ip local pool ASYNC 172.22.60.2 172.22.60.254
 ip local pool ISDN 172.22.61.2 172.22.61.254
 
!--- IP address pools for dialin clients.

 ip classless
 no ip http server
 !
 access-list 101 remark Interesting Traffic Definition to be 
 used in dialer-list 5
 access-list 101 deny   eigrp any any
 access-list 101 permit ip any any
 dialer-list 5 protocol ip list 101
 
!--- Access-list 101 defines interesting traffic. This definition is applied !--- to interface Dialer 10 and Group-Async 0 through dialer-group 5. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "5".

 !
 line con 0
  exec-timeout 0 0
  login authentication NO_AUTHEN
 
!--- Apply AAA list NO_AUTHEN configured previously. !--- That list has method "none". !--- There is no authentication on the console port.

 line 1 192
  modem InOut
 
!--- Support incoming and outgoing modem calls.

  transport input all
  autoselect during-login
 !
--- Displays the username:password prompt after modems connect.

  autoselect ppp
 
!--- Automatically launches PPP if the router detects incoming PPP packets. !--- Without this command the dialin client must manually !--- launch PPP (from Exec mode).

 line aux 0
 line vty 0 4
 !
 ntp clock-period 17180107
 ntp server 172.22.53.1
 end

maui-soho-01 (1600) 
maui-soho-01#show running-config
 Building configuration...

 Current configuration : 1609 bytes
 !
 version 12.1
 no service single-slot-reload-enable
 service timestamps debug datetime msec
 service timestamps log datetime msec
 service password-encryption
 !
 hostname maui-soho-01
 !
 logging rate-limit console 10 except errors
 !
 username admin password 7 <deleted>
 ip subnet-zero
 no ip finger
 !
 isdn switch-type basic-ni
 
!--- Switch-type for the BRI circuit. Obtain this information from the Telco.

 !
 interface Ethernet0
  ip address 10.0.0.1 255.255.255.0
  no keepalive
 !
 interface Serial0
  no ip address
  shutdown
 !
 interface BRI0
 
!--- BRI physical interface configuration.

  no ip address
 
!--- An IP address is not required on the physical BRI interface because !--- this is a dialer pool. !--- The IP addressing functionality is in interface Dialer 1 (dialer pool).

  encapsulation ppp
  dialer pool-member 1 
 
!--- Places the interface into dialer pool 1 from which Dialer interfaces !--- can draw channels as needed. !--- Links the physical interface with the logical dialer interfaces. !--- Dialer Pool 1 is defined in interface Dialer 1.

  isdn switch-type basic-ni
  isdn spid1 51255511110101 5551111
  isdn spid2 51255511120101 5551112
 
!--- Service Profile IDentifiers (SPIDs) are found primarily in North America. !--- SPIDs are not required for certain switch types. Confirm with your Telco. !--- If the Telco informs you that you do not need SPIDs, do not use these !--- two SPID commands.

  ppp authentication chap callin
 
!--- Perform one way CHAP authentication.

  ppp multilink
 
!--- Permit multilink on this BRI interface.

 !
 interface Dialer1
 
!--- This dialer is the logical interface for the dialer pool.

  ip address negotiated
 
!--- IP address for this interface is obtained from the NAS during !--- IPCP negotiation. Alternatively, you can also unnumber this interface !--- to a working interface (example, ethernet 0).

encapsulation ppp
  dialer pool 1
 
!--- Defines Dialer pool 1. !--- BRI 0 is a member of this pool.

  dialer idle-timeout 900
 
!--- Idle-timout for this link is 900 seconds (15 minutes). !--- The link is disconnected if there is no interesting traffic for 900 secs.

  dialer string 81560 class 56k
 
!--- Dial 81560 and use the map-class named "56k".

  dialer load-threshold 1 outbound
 
!--- Sets the outbound load level for traffic at which !--- additional connections are added to the MP bundle load level. !--- Values range from 1 (unloaded) to 255 (fully loaded). !--- With a threshold of 1, the additional links are immediately !--- brought up and added to the bundle.

  dialer-group 1
 
!--- Apply interesting traffic definition from dialer-list 1.

  ppp authentication chap callin
 
!--- Use one way PPP CHAP authentication.

  ppp chap hostname austin_isdn
 
!--- Use the CHAP username austin_isdn to authenticate to the other router.

  ppp chap password 7 <deleted>
 
!--- Use this CHAP password to authenticate to the other router.

  ppp multilink
 
!--- Allow multilink for the dialer profile. !--- Without this command multilink is NOT negotiated.

 !
 !
 ip classless
 ip route 0.0.0.0 0.0.0.0 Dialer1
 
!--- Set the default route to be interface Dialer 1 (the dialer pool). !--- Traffic sent to int Dialer1 causes the dialer pool member (int BRI 0) !--- to be dialed.

 no ip http server
 !
 !
 map-class dialer 56k
 
!--- Map-class named "56k" that you used with the dialer string in int Dialer1.

  dialer isdn speed 56
 
!--- Set the speed of the call to be 56k (the default speed is 64k). !--- This setting is optional for your connection. !--- Consult your Telco to find out if you need to configure the dial !--- speed to 56k.

 access-list 101 remark Interesting traffic for dialer-list 1
 access-list 101 deny   udp any any eq ntp
 access-list 101 permit ip any any
 
!--- Define NTP traffic as NOT interesting to prevent periodic NTP traffic !--- from keeping the link up indefinitely. !--- All other IP traffic is interesting. !--- Change this depending on your traffic needs.

 dialer-list 1 protocol ip list 101
 
!--- Access-list 101 defines interesting traffic. !--- Apply this to interface Dialer 1 through the command dialer-group 1. !--- Note: The specified dialer-list number must be the same as the !--- dialer-group number. In this example, the number is defined as "1"

 !
 line con 0
  transport input none
 line vty 0 4
  login
 !
 ntp clock-period 17042429
 ntp server 172.22.53.1
 end

Vérification

Cette section présente des informations que vous pouvez utiliser pour vous assurer que votre configuration fonctionne correctement.

Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.

  • show isdn status : garantit que le routeur communique correctement avec le commutateur RNIS. Dans le résultat, assurez-vous que l'état de la couche 1 est ACTIF et que l'état de l'état de la couche 2 = MULTIPLE_FRAME_ESTABLISHED apparaît. Cette commande affiche également le nombre d'appels actifs. Référez-vous à Utilisation de la commande show isdn status pour le dépannage BRI pour plus d'informations.

  • show ppp multilink : affiche des informations sur les ensembles multiliaison actifs. Utilisez cette commande pour vérifier la connexion multiliaison.

  • show dialer [numéro de type d'interface]—affiche des informations générales de diagnostic pour les interfaces configurées pour DDR. Si le numéroteur apparaît correctement, le message Dialer indique que la couche liaison de données est active. Si la couche physique apparaît, cela signifie que le protocole de ligne est apparu, mais pas le protocole NCP (Network Control Protocol). Les adresses source et de destination du paquet qui a initié la numérotation sont affichées dans la ligne Motif de numérotation. Cette commande show affiche également la configuration du minuteur, ainsi que le délai avant l'expiration de la connexion.

  • show caller user username detail - affiche les paramètres de l'utilisateur particulier, par exemple, l'adresse IP attribuée, les paramètres PPP et PPP bundle. Si votre version du logiciel Cisco IOS ne prend pas en charge cette commande, utilisez la commande show user.

  • show dialer map : affiche les mappages de numérotation dynamique et statique configurés. Vous pouvez utiliser cette commande pour vérifier si une carte de numérotation dynamique est créée. Vous ne pouvez pas acheminer les paquets sans mappage de numérotation.

Exemple de résultat de show

Voici quelques sorties show pour les appels réussis. Examinez les sections en gras et les commentaires fournis dans le résultat. Comparez le résultat obtenu avec les résultats affichés ici.

Vue générale 

maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00   
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


  Interface    User        Mode                Idle     Peer Address
  Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
     Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3

!--- Virtual-Access Interface for the two multilink PPP users.

  Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
     Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1

!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

     Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
     Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2

!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


maui-nas-02#show dialer map

!--- Observe the Dynamic Dialer Maps created for each dialin client.

Dynamic dialer map ip 172.22.60.2 name async_user () on As97
Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10

maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00   
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


  Interface    User        Mode                Idle     Peer Address
  Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
  Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3

!--- Virtual-Access Interface for the two multilink PPP users.

  Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
  Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1

!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

 Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
 Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2


!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


maui-nas-02#show dialer map

!--- Observe the Dynamic Dialer Maps created for each dialin client.

Dynamic dialer map ip 172.22.60.2 name async_user () on As97
Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10
maui-nas-02#show users
  Line         User       Host(s)              Idle       Location
* 0 con 0                 idle                 00:00:00
  97 tty 97    async_user Async interface      00:06:36   PPP: 172.22.60.2

!--- Async User. The IP address of the peer is indicated.


       Interface    User        Mode                Idle     Peer Address
       Vi1          austin_isd Virtual PPP (Bundle) 00:03:35 172.22.61.2
       Vi2          travis_isd Virtual PPP (Bundle) 00:00:20 172.22.61.3
     
!--- Virtual-Access Interface for the two multilink PPP users.

       Se0:1        austin_isd Sync PPP                    -   Bundle: Vi1
       Se0:2        austin_isd Sync PPP                    -   Bundle: Vi1
     
!--- User austin_isdn is connected through two B-channels(Multilink PPP). !--- Interface Virtual-Access 1 (Vi1) controls the two B-channels.

       Se0:3        travis_isd Sync PPP                    -   Bundle: Vi2
       Se0:4        travis_isd Sync PPP                    -   Bundle: Vi2
     
!--- User travis_isdn is connected through two B-channels (Multilink PPP). !--- Interface Virtual-Access 2 (Vi2) controls the two B-channels.


     maui-nas-02#show dialer map
     
!--- Observe the Dynamic Dialer Maps created for each dialin client.

     Dynamic dialer map ip 172.22.60.2 name async_user () on As97
     Dynamic dialer map ip 172.22.61.2 name austin_isdn () on Di10
     Dynamic dialer map ip 172.22.61.3 name travis_isdn () on Di10

Pour un appel analogique 

maui-nas-02#show caller user async_user detail

       User: async_user, line tty 97, service Async
     
!--- Shows hardware-level settings for the user named async_user.

             Active time 00:00:34, Idle time 00:00:16
       Timeouts:            Absolute  Idle      Idle
                                      Session   Exec
           Limits:          -         -         00:10:00  
           Disconnect in:   -         -         -         
       TTY: Line 97, running PPP on As97
     
!--- The call is terminated on interface Async 97. !--- This interface is included in the Group-Async configuration.

       Location: PPP: 172.22.60.2
     
!--- IP address for the peer. This address is obtained from the IP pool "ASYNC".

       DS0: (slot/unit/channel)=0/0/2
     
!--- T1 channel on which the call arrived. !--- The call arrived on channel 0 in T1 0. 

       Line: Baud rate (TX/RX) is 115200/115200, no parity, 1 stopbits, 8 databits
       Status: Ready, Active, No Exit Banner, Async Interface Active
               HW PPP Support Active
       Capabilities: Hardware Flowcontrol In, Hardware Flowcontrol Out
                     Modem Callout, Modem RI is CD, 
                     Line usable as async interface, Integrated Modem
       Modem State: Ready

       User: async_user, line As97, service PPP
     
!--- PPP setting for the user named async_user. !--- Notice that the call is terminated on int Async97.

             Active time 00:00:32, Idle time 00:00:30
       Timeouts:            Absolute  Idle
           Limits:          -         00:15:00  
           Disconnect in:   -         00:14:28  
       PPP: LCP Open, multilink Closed, CHAP (<- AAA), IPCP
     
!--- LCP state is OPEN. If LCP state is not OPEN, !--- use debug ppp negotiation to isolate LCP issues.

       LCP: -> peer, ACCM, AuthProto, MagicNumber, PCompression, ACCompression
            <- peer, ACCM, MagicNumber, PCompression, ACCompression
       NCP: Open IPCP
     
!--- IPCP state is open. If IPCP state is not OPEN, !--- use debug ppp negotiation to isolate IPCP issues.

       IPCP: <- peer, Address
             -> peer, Address
       Dialer: Connected, inbound
               Idle timer 900 secs, idle 31 secs
               Type is IN-BAND ASYNC, group As97
       IP: Local 172.22.60.1, remote 172.22.60.2
     
!--- NAS IP address and the IP address assigned to the peer.

       Counts: 27 packets input, 1545 bytes, 0 no buffer
               1 input errors, 1 CRC, 0 frame, 0 overrun
               14 packets output, 347 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets
     
!--- Packets pass through the connection.

Pour un appel RNIS 

     maui-nas-02#show caller user austin_isdn detail 
     
!--- The user named austin_isdn has two PPP links, !--- and one virtual interface bundle.


       User: austin_isdn, line Se0:3, service PPP
     
!--- Shows PPP layer settings for the first channel !--- that belongs to the user named austin_isdn.

             Active time 00:04:01, Idle time 00:00:00
       Timeouts:            Absolute  Idle
           Limits:          -         -         
           Disconnect in:   -         -         
       PPP: LCP Open, multilink Open, CHAP (<- AAA)
     
!--- LCP state is OPEN. If LCP state is not OPEN, !--- use debug ppp negotiation to isolate LCP issues.

       LCP: -> peer, AuthProto, MagicNumber, MRRU, EndpointDisc
            <- peer, MagicNumber, MRRU, EndpointDisc
       Dialer: Connected, inbound
               Type is ISDN, group Di10
     
!--- Incoming call used rotary group of int Dialer 10.

       IP: Local 172.22.61.1
     
!--- IP address of the int Loopback 1. !--- Remember that int Dialer 1 was unnumbered to Loop 1. !--- The remote IP address is indicated under the virtual-interface.

       Bundle: Member of austin_isdn, last input 00:00:00
       Counts: 55 packets input, 1635 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               82 packets output, 3479 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets

       User: austin_isdn, line Se0:4, service PPP
     
!--- Shows PPP layer settings for the second channel !--- that belongs to the user named austin_isdn.

             Active time 00:03:59, Idle time 00:00:00
       Timeouts:            Absolute  Idle
           Limits:          -         -         
           Disconnect in:   -         -         
       PPP: LCP Open, multilink Open, CHAP (<- AAA)
       LCP: -> peer, AuthProto, MagicNumber, MRRU, EndpointDisc
            <- peer, MagicNumber, MRRU, EndpointDisc
       Dialer: Connected to , inbound
               Type is ISDN, group Di10
       IP: Local 172.22.61.1
       Bundle: Member of austin_isdn, last input 00:00:00
       Counts: 50 packets input, 1589 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               77 packets output, 3429 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets       

       User: austin_isdn, line Vi1, service PPP Bundle
     
!--- Shows Virtual-Access Interface Bundle that controls the connections.

             Active time 00:04:02, Idle time 00:04:01
       Timeouts:            Absolute  Idle
           Limits:          -         00:15:00  
           Disconnect in:   -         00:10:58  
       PPP: LCP Open, multilink Open, IPCP, CDPCP
       LCP: -> peer, MagicNumber, MRRU, EndpointDisc
            <- peer
       NCP: Open IPCP, CDPCP
     
!--- IPCP State is open. If IPCP state is not OPEN, !--- use debug ppp negotiation to isolate IPCP issues.

       IPCP: <- peer, Address
             -> peer, Address
       Dialer: Connected, inbound
               Idle timer 900 secs, idle 1 secs
               Type is IN-BAND SYNC, group Di10
       IP: Local 172.22.61.1, remote 172.22.61.2
     
!--- Dialer interface (Local) IP address !--- and the IP address assigned to the peer.

       Bundle: First link of austin_isdn, 2 links, last input 00:00:01
       Counts: 12 packets input, 1712 bytes, 0 no buffer
               0 input errors, 0 CRC, 0 frame, 0 overrun
               67 packets output, 5030 bytes, 0 underruns
               0 output errors, 0 collisions, 0 interface resets

Dépannage

Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration.

Ressources de dépannage

Utilisez ces ressources selon les besoins :

Dépannage des commandes

Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.

Note : Avant d'émettre des commandes debug, consultez Informations importantes sur les commandes de débogage.

  • debug dialer : affiche les informations de débogage DDR sur les paquets reçus sur une interface de numérotation. Ces informations peuvent aider à s'assurer qu'il y a un trafic intéressant qui utilise l'interface de numérotation.

  • debug isdn q931 : affiche la configuration des appels et le démontage de la connexion réseau RNIS (couche 3).

  • debug modem : affiche l'activité de la ligne du modem sur un serveur d'accès. Le résultat s'affiche lorsque la ligne du modem change d'état.

  • debug modem csm : vous permet de résoudre les problèmes CSM (Call Switching Module) sur les routeurs équipés de modems numériques internes. Avec cette commande, vous pouvez suivre la séquence complète de commutation des appels entrants et sortants.

  • debug ppp negotiation - affiche des informations sur le trafic et les échanges PPP, et négocie les protocoles LCP (Link Control Protocol), Authentification et NCP (Network Control Protocol). Une négociation PPP réussie ouvre d’abord l’état LCP, puis s’authentifie et négocie finalement NCP. Les paramètres de liaison multiple tels que l'unité MRRU (Maximum Receive Reconstructed Unit) sont établis lors de la négociation LCP.

  • debug ppp authentication - affiche les messages du protocole d'authentification PPP, y compris les échanges de paquets CHAP et les échanges PAP (Password Authentication Protocol).

  • debug ppp error : affiche les erreurs de protocole et les statistiques d'erreur associées à la négociation et au fonctionnement de la connexion PPP.

Exemple de sortie de débogage

Voici quelques sorties de débogage pour les appels réussis. Examinez les sections en caractères gras et les commentaires fournis dans les résultats. Comparez le résultat obtenu avec le résultat affiché ici.

Pour un appel analogique 

maui-nas-02#debug isdn q931
     ISDN Q931 packets debugging is on
     maui-nas-02#debug modem
     Modem control/process activation debugging is on
     maui-nas-02#debug modem csm
     Modem Management Call Switching Module debugging is on
     maui-nas-02#debug ppp negotiation
     PPP protocol negotiation debugging is on
     maui-nas-02#debug ppp authentication
     PPP authentication debugging is on

     maui-nas-02#
     Sep 28 13:13:28.369: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5285

     
!--- Incoming Q.931 SETUP message. This indicates an incoming call. !--- For more information on Q.931 refer to !--- Troubleshooting ISDN BRI Layer 3 using the debug isdn q931 Command.

     Sep 28 13:13:28.369:   Bearer Capability i = 0x9090A2
     Sep 28 13:13:28.369:   Channel ID i = 0xA18383
     Sep 28 13:13:28.369:   Progress Ind i = 0x8183 - Origination address is non-ISDN 
     Sep 28 13:13:28.369:   Called Party Number i = 0xA1, '81560', Plan:ISDN, Type:National
     Sep 28 13:13:28.373: VDEV_ALLOCATE: 2/0 is allocated
     
!--- The Call Switch Module (CSM) is informed about the call. !--- The CSM allocates modem 2/0 to the incoming call.

     Sep 28 13:13:28.373: EVENT_FROM_ISDN::dchan_idb=0x618569F4, call_id=0x28, 
     ces=0x0 bchan=0x2, event=0x1, cause=0x0
     Sep 28 13:13:28.373:  dev in call to isdn : set dnis_collected & fap_notify
     Sep 28 13:13:28.373: EVENT_FROM_ISDN:(0028): DEV_INCALL at slot 2 and port 0
     Sep 28 13:13:28.373:  EVENT_FROM_ISDN: decode:calling 0ct3 0x0, called oct3 
     0xA1, oct3a 0x0,mask 0x3C
     Sep 28 13:13:28.373:  EVENT_FROM_ISDN: csm_call_info:calling 0ct3 0x0, 
     called oct3 0xA1, oct3a 0x0,mask 0x3C
     Sep 28 13:13:28.377: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 2, port 0
     Sep 28 13:13:28.377: Mica Modem(2/0): Configure(0x1 = 0x0) 
     Sep 28 13:13:28.377: Mica Modem(2/0): Configure(0x23 = 0x0) 
     Sep 28 13:13:28.377: Mica Modem(2/0): Call Setup
     
!--- CSM sends the Call Setup Message to Modem 2/0. !--- The modem must now go off-hook.

     Sep 28 13:13:28.377: csm_connect_pri_vdev: TS allocated at bp_stream 0, 
     bp_Ch 0,vdev_common 0x6141BB68
     Sep 28 13:13:28.377: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD285
     Sep 28 13:13:28.377:         Channel ID i = 0xA98383
     
!--- The Call Proceeding Message is sent through the D-channel.

     Sep 28 13:13:28.377: ISDN Se0:23: TX ->  ALERTING pd = 8  callref = 0xD285
     Sep 28 13:13:28.445: Mica Modem(2/0): State Transition to Call Setup
     
!--- Modem transitions to state Call Setup. !--- For more information on MICA Modem States refer to MICA Modem States.

     Sep 28 13:13:28.445: Mica Modem(2/0): Went offhook
     
!--- Modem informs the CSM that it went offhook.

     Sep 28 13:13:28.445: CSM_PROC_IC2_RING: CSM_EVENT_MODEM_OFFHOOK at slot 2, port 0
     Sep 28 13:13:28.445: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD285
     
!--- D-channel transmits a CONNECT.

     Sep 28 13:13:28.461: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5285
     
!--- The Q.931 CONNECT_ACK message is received.

     Sep 28 13:13:28.461: ISDN Se0:23: CALL_PROGRESS: CALL_CONNECTED call id 0x28, 
     bchan 2, dsl 0
     Sep 28 13:13:28.461: EVENT_FROM_ISDN::dchan_idb=0x618569F4, call_id=0x28, 
     ces=0x0 bchan=0x2, event=0x4, cause=0x0
     Sep 28 13:13:28.461: EVENT_FROM_ISDN:(0028): DEV_CONNECTED at slot 2 and port 0
     Sep 28 13:13:28.461: CSM_PROC_IC6_WAIT_FOR_CONNECT: 
     CSM_EVENT_ISDN_CONNECTED at slot 2, port 0
     Sep 28 13:13:28.465: Mica Modem(2/0): Link Initiate
     
!--- When the Q.931 CONNECT_ACK message is received, the Link initiate message !--- is sent to the MICA modem, and negotiation with remote modem occurs.

     Sep 28 13:13:28.465: %ISDN-6-CONNECT: Interface Serial0:2 is now connected to N/A N/A
     Sep 28 13:13:29.557: Mica Modem(2/0): State Transition to Connect
     
!--- Modem moves to the Connect state.

     Sep 28 13:13:34.073: Mica Modem(2/0): State Transition to Link
     Sep 28 13:13:45.478: Mica Modem(2/0): State Transition to Trainup
     Sep 28 13:13:53.642: Mica Modem(2/0): State Transition to EC Negotiating
     Sep 28 13:13:54.122: Mica Modem(2/0): State Transition to Steady State
     
!--- Modem tranistions to the Steady state.

     Sep 28 13:13:54.266: TTY97: DSR came up
     
!--- Indicates that the modem trainup is complete.

     Sep 28 13:13:54.266: tty97: Modem: IDLE->(unknown)
     Sep 28 13:13:54.266: TTY97: EXEC creation
     Sep 28 13:13:54.266: TTY97: set timer type 10, 30 seconds
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7E
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF7D
     Sep 28 13:13:57.202: TTY97: Autoselect(2) sample 7EFF7D23
     Sep 28 13:13:57.202: TTY97 Autoselect cmd:  ppp negotiate
     
!--- The router detects PPP packets and automatically launches PPP.

     Sep 28 13:13:57.206: TTY97: EXEC creation
     Sep 28 13:13:57.206: TTY97: create timer type 1, 600 seconds
     Sep 28 13:13:57.334: TTY97: destroy timer type 1
     Sep 28 13:13:57.334: TTY97: no timer type 0 to destroy
     Sep 28 13:13:57.334: As97 IPCP: Install route to 172.22.60.2
     Sep 28 13:13:59.334: %LINK-3-UPDOWN: Interface Async97, changed state to up
     Sep 28 13:13:59.334: As97 PPP: Treating connection as a callin
     Sep 28 13:13:59.334: As97 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 0 load]
     Sep 28 13:13:59.334: As97 LCP: State is Listen
     
!--- LCP negotiation begins.

     Sep 28 13:14:00.214: As97 LCP: I CONFREQ [Listen] id 3 len 23
     
!--- Incoming LCP CONFREQ. !--- For more information on how to interpret PPP debugs, refer to !--- Dialup Technology: Troubleshooting Techniques.

     Sep 28 13:14:00.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.214: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.214: As97 LCP:    Callback 6  (0x0D0306)
     Sep 28 13:14:00.214: Unthrottle 97
     Sep 28 13:14:00.214: As97 LCP: O CONFREQ [Listen] id 1 len 43
     Sep 28 13:14:00.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.214: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:00.214: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:00.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.214: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:00.214: As97 LCP:    EndpointDisc 1 Local (
     0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:00.214: As97 LCP: O CONFREJ [Listen] id 3 len 7
     Sep 28 13:14:00.214: As97 LCP:    Callback 6  (0x0D0306)
     Sep 28 13:14:00.342: As97 LCP: I CONFREQ [REQsent] id 4 len 20
     Sep 28 13:14:00.342: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.342: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.342: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.342: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:00.342: As97 LCP: O CONFACK [REQsent] id 4 len 20
     Sep 28 13:14:00.342: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:00.342: As97 LCP:    MagicNumber 0x0F7CD34A (0x05060F7CD34A)
     Sep 28 13:14:00.342: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:00.342: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.214: As97 LCP: TIMEout: State ACKsent
     Sep 28 13:14:02.214: As97 LCP: O CONFREQ [ACKsent] id 2 len 43
     Sep 28 13:14:02.214: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.214: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.214: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.214: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.214: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.214: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:02.214: As97 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:02.326: As97 LCP: I CONFREJ [ACKsent] id 2 len 22
     Sep 28 13:14:02.326: As97 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:14:02.326: As97 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:14:02.326: As97 LCP: O CONFREQ [ACKsent] id 3 len 25
     Sep 28 13:14:02.326: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.326: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.326: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.326: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.326: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.518: As97 LCP: I CONFACK [ACKsent] id 3 len 25
     Sep 28 13:14:02.518: As97 LCP:    ACCM 0x000A0000 (0x0206000A0000)
     Sep 28 13:14:02.518: As97 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:14:02.518: As97 LCP:    MagicNumber 0x3090DE31 (0x05063090DE31)
     Sep 28 13:14:02.518: As97 LCP:    PFC (0x0702)
     Sep 28 13:14:02.518: As97 LCP:    ACFC (0x0802)
     Sep 28 13:14:02.518: As97 LCP: State is Open
     
!--- LCP negotiation is complete.

     Sep 28 13:14:02.518: As97 PPP: Phase is AUTHENTICATING, 
     by this end [0 sess, 0 load]
     Sep 28 13:14:02.518: As97 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:14:02.646: As97 CHAP: I RESPONSE id 1 len 31 from "async_user"
     Sep 28 13:14:02.646: As97 AUTH: Started process 0 pid 34
     Sep 28 13:14:02.650: As97 CHAP: O SUCCESS id 1 len 4
     
!--- CHAP authentication is successful. !--- If authentication fails, check the username and password. !--- Refer to Dialup Technology: Troubleshooting Techniques 
.
     Sep 28 13:14:02.650: As97 PPP: Phase is UP [0 sess, 0 load]
     Sep 28 13:14:02.650: As97 IPCP: O CONFREQ [Closed] id 1 len 10
     
!--- IPCP negotiation begins.

     Sep 28 13:14:02.650: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:02.758: As97 IPCP: I CONFREQ [REQsent] id 1 len 40
     Sep 28 13:14:02.758: As97 IPCP:    CompressType VJ 15 slots CompressSlotID 
     (0x0206002D0F01)
     Sep 28 13:14:02.758: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:02.758: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:02.758: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     
!--- Address is obtained from the Address Pool named "Async".

     Sep 28 13:14:02.758: As97 IPCP: O CONFREJ [REQsent] id 1 len 28
     Sep 28 13:14:02.758: As97 IPCP:    CompressType VJ 15 slots CompressSlotID 
     (0x0206002D0F01)
     Sep 28 13:14:02.758: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:02.758: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:02.802: As97 CCP: I CONFREQ [Not negotiated] id 1 len 15
     Sep 28 13:14:02.802: As97 CCP:    MS-PPC supported bits 0x00000001 
     (0x120600000001)
     Sep 28 13:14:02.802: As97 CCP:    Stacker history 1 check mode EXTENDED 
     (0x1105000104)
     Sep 28 13:14:02.802: As97 LCP: O PROTREJ [Open] id 4 len 21 protocol CCP
     Sep 28 13:14:02.802: As97 LCP:  (0x80FD0101000F12060000000111050001)
     Sep 28 13:14:02.802: As97 LCP:  (0x04)
     Sep 28 13:14:02.802: As97 IPCP: I CONFACK [REQsent] id 1 len 10
     Sep 28 13:14:02.802: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:04.650: As97 IPCP: TIMEout: State ACKrcvd
     Sep 28 13:14:04.650: As97 IPCP: O CONFREQ [ACKrcvd] id 2 len 10
     Sep 28 13:14:04.650: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:04.758: As97 IPCP: I CONFACK [REQsent] id 2 len 10
     Sep 28 13:14:04.758: As97 IPCP:    Address 172.22.60.1 (0x0306AC163C01)
     Sep 28 13:14:05.750: As97 IPCP: I CONFREQ [ACKrcvd] id 2 len 34
     Sep 28 13:14:05.750: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:05.750: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:05.750: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:05.750: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.750: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.750: As97 IPCP: O CONFREJ [ACKrcvd] id 2 len 22
     Sep 28 13:14:05.750: As97 IPCP:    PrimaryWINS 0.0.0.0 (0x820600000000)
     Sep 28 13:14:05.754: As97 IPCP:    SecondaryDNS 0.0.0.0 (0x830600000000)
     Sep 28 13:14:05.754: As97 IPCP:    SecondaryWINS 0.0.0.0 (0x840600000000)
     Sep 28 13:14:05.878: As97 IPCP: I CONFREQ [ACKrcvd] id 3 len 16
     Sep 28 13:14:05.878: As97 IPCP:    Address 0.0.0.0 (0x030600000000)
     Sep 28 13:14:05.878: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.878: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.878: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 0.0.0.0, we want 172.22.60.2
     Sep 28 13:14:05.878: As97 IPCP: O CONFNAK [ACKrcvd] id 3 len 10
     Sep 28 13:14:05.878: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.990: As97 IPCP: I CONFREQ [ACKrcvd] id 4 len 16
     Sep 28 13:14:05.990: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.990: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Start.  
     Her address 172.22.60.2, we want 172.22.60.2
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Reject 172.22.60.2, using 172.22.60.2
     Sep 28 13:14:05.990: As97 AAA/AUTHOR/IPCP: Done.  
     Her address 172.22.60.2, we want 172.22.60.2
     Sep 28 13:14:05.994: As97 IPCP: O CONFACK [ACKrcvd] id 4 len 16
     Sep 28 13:14:05.994: As97 IPCP:    Address 172.22.60.2 (0x0306AC163C02)
     Sep 28 13:14:05.994: As97 IPCP:    PrimaryDNS 172.22.53.210 (0x8106AC1635D2)
     Sep 28 13:14:05.994: As97 IPCP: State is Open
     
!--- IPCP negotiation is complete. The user is now connected.

Pour un appel RNIS 

maui-nas-02#debug isdn q931
     ISDN Q931 packets debugging is on
     maui-nas-02#debug ppp negotiation
     PPP protocol negotiation debugging is on
     maui-nas-02#debug ppp authentication
     PPP authentication debugging is on

     Sep 28 13:25:02.630: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5346
     
!--- Incoming Q.931 Setup message.

     Sep 28 13:25:02.630:         Bearer Capability i = 0x8890218F
     Sep 28 13:25:02.630:         Channel ID i = 0xA18384
     Sep 28 13:25:02.630:         Called Party Number i = 0xA1, '81560', 
     Plan:ISDN, Type:National
     Sep 28 13:25:02.634: %LINK-3-UPDOWN: Interface Serial0:3, changed state to up
     Sep 28 13:25:02.638: Se0:3 PPP: Treating connection as a callin
     Sep 28 13:25:02.638: Se0:3 PPP: Phase is ESTABLISHING, 
     Passive Open [0 sess, 1 load]
     Sep 28 13:25:02.638: Se0:3 LCP: State is Listen
     Sep 28 13:25:02.638: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD346
     Sep 28 13:25:02.638:         Channel ID i = 0xA98384
     Sep 28 13:25:02.638: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD346
     Sep 28 13:25:02.638:         Channel ID i = 0xA98384
     Sep 28 13:25:02.658: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5346

     Sep 28 13:25:02.658: ISDN Se0:23: CALL_PROGRESS: 
     CALL_CONNECTED call id 0x2B, bchan 3, dsl 0
     
!--- Call is connected.

     Sep 28 13:25:02.886: Se0:3 LCP: I CONFREQ [Listen] id 61 len 28
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x1EB88B1C (0x05061EB88B1C)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:02.886: Se0:3 LCP: O CONFREQ [Listen] id 1 len 33
     Sep 28 13:25:02.886: Se0:3 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x309AFABD (0x0506309AFABD)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:02.886: Se0:3 LCP: O CONFACK [Listen] id 61 len 28
     Sep 28 13:25:02.886: Se0:3 LCP:    MagicNumber 0x1EB88B1C (0x05061EB88B1C)
     Sep 28 13:25:02.886: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.886: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:02.922: Se0:3 LCP: I CONFACK [ACKsent] id 1 len 33
     Sep 28 13:25:02.922: Se0:3 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:02.922: Se0:3 LCP:    MagicNumber 0x309AFABD (0x0506309AFABD)
     Sep 28 13:25:02.922: Se0:3 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:02.922: Se0:3 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:02.922: Se0:3 LCP: State is Open
     
!--- LCP negotiation is complete.

     Sep 28 13:25:02.922: Se0:3 PPP: 
     Phase is AUTHENTICATING, by this end [0 sess, 1 load]
     Sep 28 13:25:02.922: Se0:3 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:25:02.954: Se0:3 CHAP: I RESPONSE id 1 len 32 from "austin_isdn"
     Sep 28 13:25:02.954: Se0:3 CHAP: O SUCCESS id 1 len 4
     
!--- PPP CHAP authentication is successful.

     Sep 28 13:25:02.958: Se0:3 PPP: Phase is VIRTUALIZED [0 sess, 1 load]
     Sep 28 13:25:02.958: Vi1 PPP: Phase is DOWN, Setup [0 sess, 1 load]
     Sep 28 13:25:02.982: Vi1 PPP: Phase is DOWN, Setup [0 sess, 1 load]
     Sep 28 13:25:02.982: Se0:3 IPCP: 
     Packet buffered while building MLP bundle interface
     Sep 28 13:25:02.986: %LINK-3-UPDOWN: Interface Virtual-Access1, 
     changed state to up
     
!--- Virtual-Access Interface is up. !--- This interface controls the incoming call.

     Sep 28 13:25:02.986: Vi1 PPP: Treating connection as a callin
     Sep 28 13:25:02.986: Vi1 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 1 load]
     Sep 28 13:25:02.986: Vi1 LCP: State is Listen
     Sep 28 13:25:02.986: Vi1 PPP: Phase is UP [0 sess, 1 load]
     Sep 28 13:25:02.986: Vi1 IPCP: O CONFREQ [Closed] id 1 len 10
     Sep 28 13:25:02.986: Vi1 IPCP:    Address 172.22.61.1 (0x0306AC163D01)
     Sep 28 13:25:02.990: Vi1 MLP: Added first link Se0:3 to bundle austin_isdn
     Sep 28 13:25:02.990: Vi1 PPP: Pending ncpQ size is 1
     Sep 28 13:25:02.990: Se0:3 IPCP: Redirect packet to Vi1
     Sep 28 13:25:02.990: Vi1 IPCP: I CONFREQ [REQsent] id 45 len 10
     Sep 28 13:25:02.990: Vi1 IPCP:    Address 10.0.0.1 (0x03060A000001)
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Start.  
     Her address 10.0.0.1, we want 0.0.0.0
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Reject 10.0.0.1, using 0.0.0.0
     Sep 28 13:25:02.990: Vi1 AAA/AUTHOR/IPCP: Done.  
     Her address 10.0.0.1, we want 0.0.0.0
     Sep 28 13:25:02.990: Vi1 IPCP: O CONFNAK [REQsent] id 45 len 10
     Sep 28 13:25:02.990: Vi1 IPCP:    Address 172.22.61.2 (0x0306AC163D02)
     
!--- Peer IP address is assigned from IP Pool named "ISDN".

     Sep 28 13:25:02.990: Se0:3 CDPCP: MLP bundle interface is built, 
     process packets now 
     Sep 28 13:25:02.990: Se0:3 CDPCP: Redirect packet to Vi1
     Sep 28 13:25:02.990: Vi1 CDPCP: I CONFREQ [Not negotiated] id 23 len 4
     Sep 28 13:25:02.990: Vi1 LCP: O PROTREJ [Open] id 1 len 10 protocol CDPCP 
     (0x820701170004)
     Sep 28 13:25:03.010: Vi1 IPCP: I CONFACK [REQsent] id 1 len 10
     Sep 28 13:25:03.010: Vi1 IPCP:    Address 172.22.61.1 (0x0306AC163D01)
     Sep 28 13:25:03.010: Vi1 IPCP: I CONFREQ [ACKrcvd] id 46 len 4
     Sep 28 13:25:03.010: Vi1 IPCP: O CONFACK [ACKrcvd] id 46 len 4
     Sep 28 13:25:03.010: Vi1 IPCP: State is Open
     
!--- IPCP negotiation is complete. The call is now connected.

     Sep 28 13:25:03.014: Di10 IPCP: Install route to 172.22.61.2
     Sep 28 13:25:03.958: %LINEPROTO-5-UPDOWN: 
     Line protocol on Interface Serial0:3, changed state to up
     Sep 28 13:25:03.986: %LINEPROTO-5-UPDOWN: 
     Line protocol on Interface Virtual-Access1, changed state to up
     Sep 28 13:25:04.146: ISDN Se0:23: RX <-  SETUP pd = 8  callref = 0x5409
     
!--- The second link in the multilink connection arrives.

     Sep 28 13:25:04.150:         Bearer Capability i = 0x8890218F
     Sep 28 13:25:04.150:         Channel ID i = 0xA18385
     Sep 28 13:25:04.150:         Called Party Number i = 0xA1, '81560', Plan:ISDN, 
     Type:National
     Sep 28 13:25:04.154: %LINK-3-UPDOWN: Interface Serial0:4, changed state to up
     Sep 28 13:25:04.154: %ISDN-6-CONNECT: Interface Serial0:3 is now connected to  
     austin_isdn
     Sep 28 13:25:04.154: Se0:4 PPP: Treating connection as a callin
     Sep 28 13:25:04.154: Se0:4 PPP: Phase is ESTABLISHING, 
     Passive Open [0 sess, 1 load]
     Sep 28 13:25:04.154: Se0:4 LCP: State is Listen
     Sep 28 13:25:04.158: ISDN Se0:23: TX ->  CALL_PROC pd = 8  callref = 0xD409
     Sep 28 13:25:04.158:         Channel ID i = 0xA98385
     Sep 28 13:25:04.158: ISDN Se0:23: TX ->  CONNECT pd = 8  callref = 0xD409
     Sep 28 13:25:04.158:         Channel ID i = 0xA98385
     Sep 28 13:25:04.178: ISDN Se0:23: RX <-  CONNECT_ACK pd = 8  callref = 0x5409

     Sep 28 13:25:04.178: ISDN Se0:23: CALL_PROGRESS: 
     CALL_CONNECTED call id 0x2C, bchan 4, dsl 0
     Sep 28 13:25:04.394: Se0:4 LCP: I CONFREQ [Listen] id 51 len 28
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x1EB8910D (0x05061EB8910D)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:04.394: Se0:4 LCP: O CONFREQ [Listen] id 1 len 33
     Sep 28 13:25:04.394: Se0:4 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x309B00A6 (0x0506309B00A6)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:04.394: Se0:4 LCP: O CONFACK [Listen] id 51 len 28
     Sep 28 13:25:04.394: Se0:4 LCP:    MagicNumber 0x1EB8910D (0x05061EB8910D)
     Sep 28 13:25:04.394: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.394: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E0161757374696E5F6973646E)
     Sep 28 13:25:04.430: Se0:4 LCP: I CONFACK [ACKsent] id 1 len 33
     Sep 28 13:25:04.430: Se0:4 LCP:    AuthProto CHAP (0x0305C22305)
     Sep 28 13:25:04.430: Se0:4 LCP:    MagicNumber 0x309B00A6 (0x0506309B00A6)
     Sep 28 13:25:04.430: Se0:4 LCP:    MRRU 1524 (0x110405F4)
     Sep 28 13:25:04.430: Se0:4 LCP:    EndpointDisc 1 Local 
     (0x130E016D6175692D6E61732D3032)
     Sep 28 13:25:04.430: Se0:4 LCP: State is Open
     Sep 28 13:25:04.430: Se0:4 PPP: Phase is AUTHENTICATING, 
     by this end [0 sess, 1 load]
     Sep 28 13:25:04.430: Se0:4 CHAP: O CHALLENGE id 1 len 32 from "maui-nas-02"
     Sep 28 13:25:04.462: Se0:4 CHAP: I RESPONSE id 1 len 32 from "austin_isdn"
     Sep 28 13:25:04.466: Se0:4 CHAP: O SUCCESS id 1 len 4
     Sep 28 13:25:04.466: Se0:4 PPP: Phase is VIRTUALIZED [0 sess, 1 load]
     Sep 28 13:25:04.466: Vi1 MLP: Added link Se0:4 to bundle austin_isdn
     
!--- An additional Link is now added to exiting Virtual Interface Bundle.

     Sep 28 13:25:05.466: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:4, 
     changed state to up
     Sep 28 13:25:10.154: %ISDN-6-CONNECT: 
     Interface Serial0:4 is now connected to austin_isdn
     
!--- The second call is connected. The multilink Bundle is complete. 

     maui-nas-02#

Informations connexes

Historique de révision

Révision Date de publication Commentaires
1.0
29-Jan-2008
Première publication

Ce document vous est-il utile?

FeedbackCommentaires

Contacter Cisco

Ce document s’applique à ces produits