Este documento muestra cómo sustituir un módulo de supervisor redundante fallido en los switches Catalyst 6500 Series. Este documento explica el procedimiento para los módulos de supervisor que se ejecutan en código abierto híbrido.
Cisco recomienda que tenga conocimiento sobre estos temas:
La información que contiene este documento se basa en las siguientes versiones de software y hardware.
Cisco Catalyst 6500 Series Switch
Módulo de Supervisor: WS-SUP32-GE-3B
Código abierto híbrido:
Catalyst OS (CatOS) 8.5(8)
MSFC IOS® 12.2(18)SXF7
La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si la red está funcionando, asegúrese de haber comprendido el impacto que puede tener cualquier comando.
Este documento se puede también utilizar con estas versiones de software y hardware:
Supervisor 720 que funciona con el código abierto híbrido
Supervisor 2 que funciona con el código abierto híbrido
Consulte Convenciones de Consejos TécnicosCisco para obtener más información sobre las convenciones del documento.
Éstos son algunos de los puntos importantes relacionados con los módulos del Supervisor redundante:
En el motor del Supervisor en espera, el puerto de la consola está inactivo, el estado del módulo muestra como “recurso seguro”, y el estatus para los puertos de link ascendente se muestra normalmente.
Para permitir que usted controle el arranque de cada Supervisor Engine por separado, los registros de la configuración no se sincronizan entre los motores del supervisor.
Si las versiones de software de los dos motores del supervisor son diferentes, o si la configuración de NVRAM de los dos motores del supervisor es diferente, el motor del supervisor activo descarga automáticamente su imagen del software y configuración al motor del Supervisor en espera.
Los motores del supervisor utilizan dos imágenes de Flash: la imagen del arranque de sistema y la imagen de tiempo de ejecución. El nombre de fichero de la imagen del arranque de sistema, que se especifica en la variable de entorno del INICIO, se salva en el NVRAM. La imagen de tiempo de ejecución es la imagen del arranque de sistema que el monitor de la memoria ROM utiliza para iniciar el Supervisor Engine. Después de los arranques del sistema, la imagen de tiempo de ejecución reside en el RAM dinámica (DRAM).
Los motores del supervisor redundante deben ser del mismo tipo con la misma placa de función modelo. El WS-X6K-SUP1-2GE y el WS-X6K-SUP1A-2GE, son que sin los indicadores luminosos LED amarillo de la placa muestra gravedad menor de función de políticas (PFC), son compatibles para la Redundancia. Para los motores del supervisor con los PFC, los PFC deben ser idénticos para la Redundancia (dos PFC, dos PFC2, dos PFC3A, dos PFC3Bs, o dos PFC3BXLs).
Esta sección proporciona el procedimiento paso a paso para substituir el módulo de Supervisor 32 en un Catalyst 6500 Series Switch. Este ejemplo utiliza un Cisco Catalyst 6509 Switch, que tiene dos módulos de Supervisor en el slot 5 y 6. El módulo de Supervisor en el slot 6 ha fallado. Se asume que el módulo de Supervisor fallado en el slot 6 está quitado del chasis. Usted puede ver el procedimiento para agregar el nuevo módulo de Supervisor en el slot 6.
Si usted tiene un Cisco Catalyst 6500 Series Switch adicional, el usted puede conectarse el nuevo supervisor en el Switch y actualización o retrocede el código abierto híbrido al mismo nivel que el supervisor en el slot 5 del switch de producción. Si usted tiene el mismo código abierto híbrido en el nuevo módulo de Supervisor, usted no necesita configurar cualquier cosa en el nuevo módulo de Supervisor. Cuando usted agrega el módulo de Supervisor en el slot 6, del supervisor activo del motor los synchs automáticamente la configuración. Esta sección muestra el proceso gradual y la lista de verificación durante el reemplazo del supervisor.
Éste es el procedimiento paso a paso para substituir el módulo de Supervisor 32 en un Catalyst 6500 Series Switch:
Agregue el módulo de Supervisor en el slot 6.
Si usted tiene conexión de consola al supervisor en el slot 6, usted debe ver esta salida:
!--- Supervisor module at slot 6 System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2004 by cisco Systems, Inc. Cat6k-Sup32 platform with 524288 Kbytes of main memory Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin" Self decompressing the image : ############################################ ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ########################################################################### ##################################################### [OK] System Power On Diagnostics DRAM Size ..........................512 MB Testing DRAM .......................Passed Verifying Text Segment .............Passed NVRAM Size .........................2048 KB Level2 Cache .......................Present Level3 Cache .......................Absent System Power On Diagnostics Complete Currently running ROMMON from S (Gold) region Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin Firmware compiled 01-Dec-06 12:57 by integ Build [100] This module is now in standby mode. Console is disabled for standby supervisor.
Esta salida muestra la consola del supervisor activo en el slot 5:
Access2> (enable) Access2> (enable) Access2> (enable) 2007 May 22 19:17:48 %SYS-5-MOD_INSERT:Module 6 has been inserted Access2> (enable) Access2> (enable) Access2> (enable) %SYS-5-SUP_MODSBY:Module 6 is in standby mode %SYS-5-SUP_IMGSYNC:File synchronization process will start in 120 seconds %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal Diagnostics... %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/1 is not supported %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/2 is not supported %SYS-5-PORT_SSUPOK:Ports on standby supervisor (module 6) are up %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6 %DIAG-6-RUN_MINIMUM:Module 16: Running Minimal Diagnostics... %DIAG-6-DIAG_OK:Module 16: Passed Online Diagnostics %SYS-5-MOD_OK:Module 16(WS-F6K-MSFC2A,SAL1018LQ3C) is online %MGMT-5-SYS_CONFIG_START_MOD_FAIL:Unable to start system configuration for module 6 %MGMT-5-SYS_CONFIG_START_MOD_FAIL:Unable to start system configuration for module 16 %SYS-5-SUP_IMGSYNCSTART:Active supervisor is synchronizing bootdisk: cat6000-sup32pfc3k8.8-5-8.bin %SYS-5-SUP_IMGSYNCFINISH:Active supervisor has synchronized bootdisk: cat6000-sup32pfc3k8.8-5-8.bin Access2> (enable)
Verifique el estatus de la redundancia de Supervisor:
Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: ON Access2> (enable)
Verifique el estatus de la Redundancia MSFC:
Access2> (enable) session 15 Trying Router-15... Connected to Router-15. Escape character is '^]'. LAB-Router>enable LAB-Router#show redundancy Redundant System Information : ------------------------------ Available system uptime = 10 minutes Switchovers system experienced = 0 Standby failures = 0 Last switchover reason = unsupported Hardware Mode = Duplex Configured Redundancy Mode = Stateful SwitchOver - SSO Operating Redundancy Mode = Stateful SwitchOver - SSO Maintenance Mode = Disabled Communications = Up Current Processor Information : ------------------------------- Active Location = slot 5 Current Software state = ACTIVE Uptime in current state = 10 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 Peer Processor Information : ---------------------------- Standby Location = slot 6 Current Software state = STANDBY HOT Uptime in current state = 2 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 LAB-Router#
Fuerce la falla de Supervisor y la prueba:
!--- Supervisor in slot 5 Access2> (enable) switch supervisor This command will force a switch-over to the standby Supervisor module. Do you want to continue (y/n) [n]? y 2007 May 21 20:40:37 %SYS-5-MOD_RESET:Module 5 reset from Console// Access2> (enable) System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2004 by cisco Systems, Inc. Cat6k-Sup32 platform with 262144 Kbytes of main memory Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin" Self decompressing the image : ############################################## ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ##################################################### [OK] System Power On Diagnostics DRAM Size ..........................256 MB Testing DRAM .......................Passed Verifying Text Segment .............Passed NVRAM Size .........................2048 KB Level2 Cache .......................Present Level3 Cache .......................Absent System Power On Diagnostics Complete Currently running ROMMON from S (Gold) region Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin Firmware compiled 01-Dec-06 12:57 by integ Build [100] This module is now in standby mode. Console is disabled for standby supervisor
Consuele en el supervisor 6 y verifique el supervisor y la configuración de MSFC.
Esta sección explica el procedimiento paso a paso para substituir el módulo de Supervisor 32 en un Catalyst 6500 Series Switch. Este ejemplo utiliza un Cisco Catalyst 6509 Switch que tenga dos módulos de Supervisor en el slot 5 y 6. El módulo de Supervisor en el slot 6 ha fallado. Se asume que el módulo de Supervisor fallado en el slot 6 está quitado del chasis. Usted puede ver el procedimiento para agregar el nuevo módulo de Supervisor en el slot 6.
Si usted no tiene una opción para actualizar el nuevo código abierto híbrido del supervisor a la misma versión que el supervisor activo, usted puede realizar este procedimiento para agregar el módulo de Supervisor y para sincronizar el código abierto híbrido y la configuración del switch. La mayor parte del procedimiento se automatiza. Este documento muestra el proceso gradual y la lista de verificación que se realizarán durante el reemplazo del supervisor.
Esta sección le muestra la salida de la demostración del Switch sin el supervisor en el slot 6.
Show module
Variable de arranque
Módulo show hecho salir:
Access2> (enable) show module Mod Slot Ports Module-Type Model Sub Status --- ---- ----- ------------------------- ------------------- --- -------- 1 1 0 1000BaseX Ethernet no power-down 2 2 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 5 5 9 1000BaseX Supervisor WS-SUP32-GE-3B yes ok 15 5 1 Multilayer Switch Feature WS-F6K-MSFC2A no ok 7 7 5 Communication Media Mod. WS-SVC-CMM no ok 8 8 0 FXS no power-down 9 9 0 10/100BaseTX Ethernet no power-down !--- Output suppressed Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw --- ----------------------- ------------------- ----------- ------ ------ 3 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 4 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 5 L3 Switching Engine III WS-F6K-PFC3B SAL1012GREU 2.1 Access2> (enable)
Demostración version output:
Access2> (enable) show version WS-C6509 Software, Version NmpSW: 8.5(8) Copyright (c) 1995-2006 by Cisco Systems NMP S/W compiled on Dec 1 2006, 23:03:43 System Bootstrap Version: 12.2 System Boot Image File is 'bootdisk:cat6000-sup32pfc3k8.8-5-8.bin' System Configuration register is 0x2102 Hardware Version: 2.0 Model: WS-C6509 Serial #: SCA034500F5 PS1 Module: WS-CAC-6000W Serial #: AZS10130G7T Mod Port Model Serial # Versions --- ---- ------------------- ----------- -------------------------------------- 2 48 WS-X6248-RJ-45 SAD03431007 Hw : 1.1 Fw : 4.2(0.24)VAI78 Sw : 8.5(8) 3 48 WS-X6348-RJ-45 SAD04150A2T Hw : 1.1 Fw : 5.3(1) Sw : 8.5(8) WS-F6K-VPWR Hw : 1.0 Sw : 1.1(1) 4 48 WS-X6348-RJ-45 SAD05070CNX Hw : 2.0 Fw : 5.4(2) Sw : 8.5(8) WS-F6K-VPWR Hw : 1.0 Sw : 1.1(1) 5 9 WS-SUP32-GE-3B SAL1010F8KG Hw : 4.2 Fw : 12.2 Fw1: 8.5(8) Sw : 8.5(8) Sw1: 8.5(8) WS-F6K-PFC3B SAL1012GREU Hw : 2.1 Sw : 7 5 WS-SVC-CMM SAD100707YJ Hw : 2.8 Fw : 12.4(7a), Sw : 12.4(7a), 15 1 WS-F6K-MSFC2A SAL1012GG1X Hw : 3.0 Fw : 12.2(18)SXF7 Sw : 12.2(18)SXF7 DRAM FLASH NVRAM Module Total Used Free Total Used Free Total Used Free ------ ------- ------- ------- ------- ------- ------- ----- ----- ----- 5 262144K 124421K 137723K 249772K 9796K 239976K 2048K 366K 1682K Uptime is 0 day, 0 hour, 3 minutes Access2> (enable)
Variable de arranque:
!--- Current working directory Access2> (enable) pwd bootdisk !--- Files in the bootdisk Access2> (enable) dir 2 -rw- 10029260 Dec 13 2006 15:37:08 cat6000-sup32pfc3k8.8-5-8.bin 245735424 bytes available (10031104 bytes used) !--- Boot variable Access2> (enable) show boot BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1; CONFIG_FILE variable = bootflash:switch.cfg Configuration register is 0x2102 ignore-config: disabled auto-config: non-recurring, overwrite, sync disabled ROMMON console baud: 9600 boot: image specified by the boot system commands Image auto sync is enabled Image auto sync timer is 120 seconds Access2> (enable)
El módulo de Supervisor se inserta en el slot 6. Muestran la salida de la consola de los módulos del active y del Supervisor en espera cuando usted agrega el nuevo módulo del Supervisor en espera en el Switch aquí:
Inserte el nuevo módulo de Supervisor en el slot 6.
Usted puede ver este mensaje del registro en el módulo supervisor activo:
Access2> (enable) 2007 May 21 20:21:14 %SYS-5-MOD_INSERT:Module 6 has been inserted
Si usted ha consolado en el Supervisor en espera en 6, usted puede ver este proceso de arranque:
System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2004 by cisco Systems, Inc. Cat6k-Sup32 platform with 524288 Kbytes of main memory Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-4-5.bin" Self decompressing the image : ############################################## ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ############################################################################# ######################################################################## [OK] System Power On Diagnostics DRAM Size ..........................512 MB Testing DRAM .......................Passed Verifying Text Segment .............Passed NVRAM Size .........................2048 KB Level2 Cache .......................Present Level3 Cache .......................Absent System Power On Diagnostics Complete Currently running ROMMON from S (Gold) region Boot image: bootdisk:cat6000-sup32pfc3k8.8-4-5.bin Firmware compiled 02-Aug-05 16:08 by integ Build [100] This module is now in standby mode. Console is disabled for standby supervisor
Usted puede verificar el estado de redundancia del módulo supervisor activo en el slot 5.
Access2> (enable) 2007 May 21 20:23:09 %SYS-5-SUP_MODSBY:Module 6 is in standby mode 2007 May 21 20:23:11 %SYS-5-SUP_IMGSYNCSTART:Active supervisor is synchronizing bootdisk:cat6000-sup32pfc3k8.8-5-8.bin Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: OFF(standby-supervisor-image-incompatible)
El módulo supervisor activo copia el CatOS en el módulo del Supervisor en espera. También configura la variable de arranque del motor del Supervisor en espera al nuevo CatOS.
Access2> (enable) 2007 May 21 20:24:23 %SYS-5-SUP_IMGSYNCFINISH:Active superviso r has synchronized bootdisk:cat6000-sup32pfc3k8.8-5-8.bin
Después de que la imagen de CatOS se copie al Supervisor en espera, las recargas del módulo en espera 6 automáticamente con la nueva imagen.
This module is now in standby mode. Console is disabled for standby supervisor System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2004 by cisco Systems, Inc. Cat6k-Sup32 platform with 524288 Kbytes of main memory Autoboot executing command: "boot bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin" Self decompressing the image : ################################################# ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ##################################################### [OK] System Power On Diagnostics DRAM Size ..........................512 MB Testing DRAM .......................Passed Verifying Text Segment .............Passed NVRAM Size .........................2048 KB Level2 Cache .......................Present Level3 Cache .......................Absent System Power On Diagnostics Complete Currently running ROMMON from S (Gold) region Boot image: bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin Firmware compiled 01-Dec-06 12:57 by integ Build [100] This module is now in standby mode. Console is disabled for standby supervisor
Una vez que el módulo en espera está para arriba, usted puede verificar el estado de redundancia del módulo supervisor activo.
Access2> (enable) 2007 May 21 20:26:22 %SYS-5-SUP_MODSBY:Module 6 is in standby mode 2007 May 21 20:26:23 %SYS-5-SUP_IMGSYNC:File synchronization process will start in 120 seconds 2007 May 21 20:27:08 %SYS-1-SYS_LCPERR1:Module 16: RP requested reset of peer RP : MSFC on module 16 will be reset 2007 May 21 20:27:24 %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal Diagnostics.. . 2007 May 21 20:27:24 %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics 2007 May 21 20:27:25 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/1 is not supported 2007 May 21 20:27:25 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/2 is not supported 2007 May 21 20:27:25 %SYS-5-PORT_SSUPOK:Ports on standby supervisor (module 6) a re up 2007 May 21 20:27:25 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6 2007 May 21 20:28:24 %SYS-5-SUP_IMGSYNCSTART:Active supervisor is synchronizing bootdisk:cat6000-sup32pfc3k8.8-5-8.bin 2007 May 21 20:28:25 %SYS-5-SUP_IMGSYNCFINISH:Active supervisor has synchronized bootdisk:cat6000-sup32pfc3k8.8-5-8.bin Access2> (enable)
Access2> (enable) dir 2 -rw- 10029260 Dec 13 2006 15:37:08 cat6000-sup32pfc3k8.8-5-8.bin 245735424 bytes available (10031104 bytes used) Access2> (enable) dir 6/ 2 -rw- 9356096 May 11 2006 19:04:09 cat6000-sup32pfc3k8.8-4-5.bin 2287 -rw- 10029260 May 21 2007 20:24:10 RTSYNC_cat6000-sup32pfc3k8.8-5- 8.bin !--- You can see the copied CatOS name starts with RTSYNC_ 236900352 bytes available (19390464 bytes used) Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: ON
Siga estos pasos:
Módulo show hecho salir:
Access2> (enable) show module Mod Slot Ports Module-Type Model Sub Status --- ---- ----- ------------------------- ------------------- --- -------- 1 1 0 1000BaseX Ethernet no power-down 2 2 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 5 5 9 1000BaseX Supervisor WS-SUP32-GE-3B yes ok 15 5 1 Multilayer Switch Feature WS-F6K-MSFC2A no ok 6 6 9 1000BaseX Supervisor WS-SUP32-GE-3B yes standby 7 7 5 Communication Media Mod. WS-SVC-CMM no ok 8 8 0 FXS no power-down 9 9 0 10/100BaseTX Ethernet no power-down !--- Output suppressed Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw --- ----------------------- ------------------- ----------- ------ ------ 3 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 4 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 5 L3 Switching Engine III WS-F6K-PFC3B SAL1012GREU 2.1 6 L3 Switching Engine III WS-F6K-PFC3B SAL1017L9WJ 2.1
Verifique el Redundancia-historial:
Access2> (enable) show system redundancy-history Maximum entries of switchover history table = 10 System cold start due to switchover failure = 4 Standby available time (secs*100) = 33291 Redundant History Switchover Table:
El CatOS se copia automáticamente durante el proceso del SINCRONIZAR. Sin embargo, el IOS en el MSFC no se copia automáticamente.
Verifique el IOS y la Redundancia del MSFC:
!--- 1. Connect to MSFC Access2> (enable) session 15 Trying Router-15... Connected to Router-15. Escape character is '^]'. LAB-Router>enable !--- 2. Verify the IOS file in the bootflash LAB-Router#dir Directory of bootflash:/ 1 -rwx 17966324 Dec 13 2006 15:12:29 +00:00 c6msfc2a-adventerprisek9_w an-mz.122-18.SXF7.bin 65536000 bytes total (47569548 bytes free) !--- 3. Show version output LAB-Router#show version Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw Image text-base: 0x40101040, data-base: 0x42638000 ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1) BOOTLDR: MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) LAB-Router uptime is 26 minutes System returned to ROM by power-on System image file is "bootflash:c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin" !--- 4. MSFC redundancy status LAB-Router#show redundancy Redundant System Information : ------------------------------ Available system uptime = 4 minutes Switchovers system experienced = 0 Standby failures = 0 Last switchover reason = unsupported Hardware Mode = Duplex Configured Redundancy Mode = Stateful SwitchOver - SSO Operating Redundancy Mode = Route Processor Redundancy !--- It is running in the RPR mode because the standby MSFC !--- is running different version of IOS. Maintenance Mode = Disabled Communications = Up Current Processor Information : ------------------------------- Active Location = slot 5 Current Software state = ACTIVE Uptime in current state = 4 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 Peer Processor Information : ---------------------------- Standby Location = slot 6 Current Software state = STANDBY COLD Uptime in current state = 2 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-IPBASE_WAN-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Mar-06 14:53 by tinhuang BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 !--- Note that the boot variable is blank. The MSFC boots the !--- first IOS image in the bootflash: LAB-Router# LAB-Router#exit Access2> (enable)
Actualice el IOS en el MSFC espera.
Copie la imagen del IOS al MSFC espera:
LAB-Router#copy c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin slavebootflash:/ Destination filename [c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 17966324 bytes copied in 44.180 secs (406662 bytes/sec) LAB-Router# !--- Delete the old IOS image. Because the boot variable is blank !--- and the MSFC boots the first IOS image in the bootflash: LAB-Router#cd slavebootflash: LAB-Router#delete c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin Delete filename [c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin]? Delete slavebootflash:c6msfc2a-ipbase_wan-mz.122-18.SXF4.bin? [confirm] LAB-Router#
Recargue el módulo del Supervisor en espera:
LAB-Router#exit Access2> (enable) reset 6 This command will reset module 6. Do you want to continue (y/n) [n]? y 2007 May 21 21:14:03 %SYS-5-MOD_RESET:Module 6 reset from Console// Resetting module 6... Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: OFF(standby-supervisor-not-present) Access2> (enable) 2007 May 21 21:16:01 %SYS-5-SUP_MODSBY:Module 6 is in standby mode 2007 May 21 21:16:02 %SYS-5-SUP_IMGSYNC:File synchronization process will start in 120 seconds 2007 May 21 21:16:03 %DIAG-6-RUN_MINIMUM:Module 6: Running Minimal Diagnostics.. . 2007 May 21 21:16:05 %DIAG-6-DIAG_OK:Module 6: Passed Online Diagnostics 2007 May 21 21:16:06 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/1 is not supported 2007 May 21 21:16:06 %SYS-3-TRANSCEIVER_NOTSUPP: Transceiver on port 6/2 is not supported 2007 May 21 21:16:06 %SYS-5-PORT_SSUPOK:Ports on standby supervisor (module 6) are up 2007 May 21 21:16:07 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 6 2007 May 21 21:16:49 %SYS-1-SYS_LCPERR1:Module 16: RP requeste d reset of peer RP: MSFC on module 16 will be reset Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: ON Access2> (enable)
Verifique el IOS MSFC después de la actualización:
Access2> (enable) session 15 Trying Router-15... Connected to Router-15. Escape character is '^]'. LAB-Router>enable LAB-Router#show redundancy Redundant System Information : ------------------------------ Available system uptime = 17 minutes Switchovers system experienced = 0 Standby failures = 1 Last switchover reason = unsupported Hardware Mode = Duplex Configured Redundancy Mode = Stateful SwitchOver - SSO Operating Redundancy Mode = Stateful SwitchOver - SSO Maintenance Mode = Disabled Communications = Up Current Processor Information : ------------------------------- Active Location = slot 5 Current Software state = ACTIVE Uptime in current state = 17 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 Peer Processor Information : ---------------------------- Standby Location = slot 6 Current Software state = STANDBY HOT Uptime in current state = 0 minutes Image Version = Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw BOOT = CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 LAB-Router#
Ahora, usted puede Conmutación por falla el módulo de Supervisor al módulo nuevamente agregado del Supervisor en espera y probarlo.
Conmutación por falla el módulo de Supervisor:
Access2> (enable) switch supervisor This command will force a switch-over to the standby Supervisor module. Do you want to continue (y/n) [n]? y 2007 May 21 20:40:37 %SYS-5-MOD_RESET:Module 5 reset from Console// Access2> (enable) System Bootstrap, Version 12.2(18r)SX2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2004 by cisco Systems, Inc. Cat6k-Sup32 platform with 262144 Kbytes of main memory Autoboot executing command: "boot bootdisk:cat6000-sup32pfc3k8.8-5-8.bin" Self decompressing the image : ################################################# ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ##################################################### [OK] System Power On Diagnostics DRAM Size ..........................256 MB Testing DRAM .......................Passed Verifying Text Segment .............Passed NVRAM Size .........................2048 KB Level2 Cache .......................Present Level3 Cache .......................Absent System Power On Diagnostics Complete Currently running ROMMON from S (Gold) region Boot image: bootdisk:cat6000-sup32pfc3k8.8-5-8.bin Firmware compiled 01-Dec-06 12:57 by integ Build [100] This module is now in standby mode. Console is disabled for standby supervisor
Consuele en el supervisor 6, que ahora es el módulo activo.
Estado de redundancia:
Access2> (enable) show system highavailability Highavailability: enabled Highavailability versioning: disabled Highavailability Operational-status: ON Access2> (enable) show system redundancy-history Maximum entries of switchover history table = 10 System cold start due to switchover failure = 4 Standby available time (secs*100) = 98984 Redundant History Switchover Table: Index: 1 Previous active supervisor module: 5 Current active supervisor module : 6 Switchover reason : user initiated Switchover time : Mon May 21 2007, 20:40:37
Versión de la demostración:
Access2> (enable) show version WS-C6509 Software, Version NmpSW: 8.5(8) Copyright (c) 1995-2006 by Cisco Systems NMP S/W compiled on Dec 1 2006, 23:03:43 System Bootstrap Version: 12.2 System Boot Image File is 'bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin' System Configuration register is 0x2102
Variable de arranque:
Access2> (enable) show boot BOOT variable = bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin,1;bootdisk:cat6000 -sup32pfc3k8.8-4-5.bin,1; CONFIG_FILE variable = bootdisk:switch.cfg Configuration register is 0x2102 ignore-config: disabled auto-config: non-recurring, overwrite, sync disabled ROMMON console baud: 9600 boot: image specified by the boot system commands Image auto sync is enabled Image auto sync timer is 120 seconds
Módulo show:
Access2> (enable) show module Mod Slot Ports Module-Type Model Sub Status --- ---- ----- ------------------------- ------------------- --- -------- 1 1 Unknown Card power-down 2 2 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 5 5 9 1000BaseX Supervisor WS-SUP32-GE-3B yes standby 6 6 9 1000BaseX Supervisor WS-SUP32-GE-3B yes ok 16 6 1 Multilayer Switch Feature WS-F6K-MSFC2A no ok 7 7 5 Communication Media Mod. WS-SVC-CMM no ok 8 8 0 FXS no power-down 9 9 Unknown Card power-down !--- Output suppressed Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw --- ----------------------- ------------------- ----------- ------ ------ 3 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 4 Inline Power Module WS-F6K-VPWR 1.0 1.1(1) 5 L3 Switching Engine III WS-F6K-PFC3B SAL1012GREU 2.1 6 L3 Switching Engine III WS-F6K-PFC3B SAL1017L9WJ 2.1 Access2> (enable)
Verifique el MSFC:
Access2> (enable) session 16 Trying Router-16... Connected to Router-16. Escape character is '^]'. LAB-Router>enable LAB-Router#show version Cisco Internetwork Operating System Software IOS (tm) MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 01:03 by kellythw Image text-base: 0x40101040, data-base: 0x42638000 ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1) BOOTLDR: MSFC2A Software (C6MSFC2A-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) LAB-Router uptime is 7 minutes System returned to ROM by Stateful Switchover System image file is "bootflash:c6msfc2a-adventerprisek9_wan-mz.122-18.SXF7.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco MSFC2A (R7000) processor (revision MSFC2A) with 458752K/65536K bytes of me mory. Processor board ID MSFC2A R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache Last reset from power-on SuperLAT software (copyright 1990 by Meridian Technology Corp). X.25 software, Version 3.0.0. Bridging software. TN3270 Emulation software. 29 Virtual Ethernet/IEEE 802.3 interfaces 509K bytes of non-volatile configuration memory. 65536K bytes of Flash internal SIMM (Sector size 512K). Configuration register is 0x2102
Usted puede ver que el nombre de CatOS en el módulo de Supervisor substituido comienza con RTSYNC. Usted puede dejar el sistema para ejecutarse mientras que es. Usted puede también cambiar el nombre del archivo y guardarlo como nombre estándar como se muestra aquí:
Access2> (enable) rename RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin cat6000-sup32pfc3k 8.8-5-8.bin Access2> (enable) dir 2287 -rw- 10029260 May 21 2007 21:40:01 cat6000-sup32pfc3k8.8-5-8.bin 236900352 bytes available (19390464 bytes used) Access2> (enable)
Después de que usted retitule el archivo, usted debe cambiar la variable de arranque.
!--- Verify boot variable Access2> (enable) show boot BOOT variable = bootdisk:RTSYNC_cat6000-sup32pfc3k8.8-5-8.bin,1;bootdisk:cat6000 -sup32pfc3k8.8-4-5.bin,1; CONFIG_FILE variable = bootdisk:switch.cfg Configuration register is 0x2102 ignore-config: disabled auto-config: non-recurring, overwrite, sync disabled ROMMON console baud: 9600 boot: image specified by the boot system commands Image auto sync is enabled Image auto sync timer is 120 seconds !--- Clear all the boot variables Access2> (enable) clear boot system all BOOT variable = Access2> (enable) 2007 May 21 21:41:56 %SYS-5-SUP_IMGSYNC:File synchronization p rocess will start in 120 seconds !--- Configure the boot variable Access2> (enable) set boot system flash bootdisk:cat6000-sup32pfc3k8.8-5-8.bin BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1; Access2> (enable) 2007 May 21 21:42:14 %SYS-5-SUP_IMGSYNC:File synchronization p rocess will start in 120 seconds !--- Verify the boot variable Access2> (enable) show boot BOOT variable = bootdisk:cat6000-sup32pfc3k8.8-5-8.bin,1; CONFIG_FILE variable = bootdisk:switch.cfg Configuration register is 0x2102 ignore-config: disabled auto-config: non-recurring, overwrite, sync disabled ROMMON console baud: 9600 boot: image specified by the boot system commands Image auto sync is enabled Image auto sync timer is 120 seconds