Introducción
En este documento, se describe cómo configurar el VLAN Trunk Protocol (VTP).
Prerequisites
Requirements
No hay requisitos específicos para este documento.
Componentes Utilizados
Este documento no tiene restricciones específicas en cuanto a versiones de software y de hardware.
La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si tiene una red en vivo, asegúrese de entender el posible impacto de cualquier comando.
Convenciones
Consulte Convenciones de Consejos Técnicos de Cisco para obtener más información sobre las convenciones del documento.
Antecedentes
El VTP reduce la administración en una red conmutada. Al configurar una VLAN nueva en un servidor VTP, se distribuye la VLAN a través de todos los switches del dominio. Esto reduce la necesidad de configurar la misma VLAN en todas partes. VTP es un protocolo de propiedad de Cisco que está disponible en la mayoría de los productos de la serie Cisco Catalyst.
Consulte Comprensión del VLAN Trunk Protocol (VTP)para obtener más información sobre VTP.
Nota: Solo los usuarios registrados de Cisco pueden acceder al sitio, las herramientas y los documentos internos.
Configurar
Directrices de Configuración de VTP
En esta sección, se proporcionan directrices para configurar el VTP en la red.
-
Todos los switches tienen el mismo nombre de dominio VTP, a menos que el diseño de red requiera dominios VTP diferentes.
Nota: La negociación troncal no funciona en los dominios VTP. Consulte la sección Tráfico de datos bloqueado entre dominios VTP de Configure VLAN Trunk Protocol (VTP) para obtener más información.
-
Todos los switches de un dominio VTP deben ejecutar la misma versión de VTP.
-
Todos los switches en un dominio VTP tienen la misma contraseña VTP, si la hay.
-
Todos los switches servidores de VTP deben tener el mismo número de revisión de configuración, que además debe ser el mayor dentro del dominio.
-
Al cambiar el modo VTP de un switch de Transparente a Servidor, las VLAN configuradas en el switch VTP Transparente deben existir en el switch Servidor.
Configuración de VTP en switches Catalyst
En esta sección, se proporcionan algunos comandos básicos para configurar VTP en los switches Catalyst más utilizados.
Había dos métodos para configurar VTP, como se muestra en esta sección. La disponibilidad de estos métodos puede diferir de la versión del software Cisco IOS®. Por ejemplo, el Método 1 no está disponible en las versiones más recientes del IOS de Cisco; por otro lado, el Método 2 (el modo de configuración global) no está disponible en las versiones de software heredadas.
-
Método 1, en modo de base de datos VLAN:
En Cisco IOS Software, se puede configurar el nombre de dominio VTP, el modo VTP y las VLAN en el modo de configuración de VLAN.
-
En el modo EXEC, emita el siguiente comando para ingresar al modo de configuración VLAN:
Switch#vlan database
!--- Issue this command in privileged EXEC mode,
!--- not in global configuration mode.
Switch(vlan)#
!--- This is VLAN configuration mode.
-
Emita el siguiente comando para configurar el nombre de dominio VTP:
Switch(vlan)#vtp domain example
-
Emita el siguiente comando para configurar el modo VTP:
Switch(vlan)#vtp {client | server | transparent}
-
Emita el comando exit para salir del modo de configuración de VLAN.
Nota: Los comandos end y Ctrl-Z no funcionan en este modo.
Switch(vlan)#end
Switch(vlan)#^Z
% Invalid input detected at '^' marker.
Switch(vlan)#
Swtch(vlan)#exit
APPLY completed.
Exiting....
Switch#
-
Método 2, en modo de configuración global:
En el modo de configuración global de Cisco IOS Software, se pueden configurar todos los parámetros VTP con los comandos de Cisco IOS Software. El siguiente es el formato de comando:
Switch(config)#vtp ?
domain Set the name of the VTP administrative domain.
file Configure IFS filesystem file where VTP configuration is stored.
interface Configure interface as the preferred source for the VTP IP updater
address.
mode Configure VTP device mode
password Set the password for the VTP administrative domain
pruning Set the administrative domain to permit pruning
version Set the administrative domain to VTP version
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vtp domain ?
WORD The ascii name for the VTP administrative domain.
Switch(config)#vtp domain example
Changing VTP domain name from example to example
Switch(config)#vtp mode server
-
Emita los siguientes comandos para supervisar el estado y el funcionamiento de VTP:
Switch#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : example
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.226 at 0-0-00 00:00:00
Local updater ID is 10.122.190.226 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 0
MD5 digest : 0x0A 0xF4 0xFD 0xE9 0x99 0xD7 0xAB 0x3F
0x0A 0x64 0x04 0x7C 0x42 0x98 0xD8 0xE5
Switch#
Switch#show vtp counters
VTP statistics:
Summary advertisements received : 0
Subset advertisements received : 0
Request advertisements received : 0
Summary advertisements transmitted : 0
Subset advertisements transmitted : 0
Request advertisements transmitted : 0
Number of config revision errors : 0
Number of config digest errors : 0
Number of V1 summary errors : 0
VTP pruning statistics:
Trunk Join Transmitted Join Received Summary advts received from
non-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Switch#
Ejemplos prácticos
Ejemplo 1:
En este ejemplo, se incluyen dos switches Catalyst 4500 que están conectados por un link TenGigabitEthernet:
-
Swithc-A es un switch nuevo que no tiene nombre de dominio VTP ni VLAN. Switch -C es un switch que existe actualmente y que se ejecuta con 16 VLAN en la prueba de dominio VTP.
-
En este ejemplo de salida del comando show vtp status, puede ver que la versión de VTP se establece de forma predeterminada en 1. Y el Switch-A es compatible con VTP V2. Sin embargo, el switch no ejecuta la V2 de VTP en este caso. El switch solo ejecuta VTP V2 si la versión V2 está configurada con el comando VTP versión 2. En este ejemplo, el Switch-A está configurado como cliente VTP. También es importante asegurarse de que el switch conectado tenga una Revisión de configuración de 0, o un valor menor que el servidor VTP actual antes de que se conecte a la red:
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 10.122.190.226 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 5
Configuration Revision : 0
MD5 digest : 0x57 0xCD 0x40 0x65 0x63 0x59 0x47 0xBD
0x56 0x9D 0x4A 0x3E 0xA5 0x69 0x35 0xBC
Switch-A#
Switch-A#
Switch-A#
Switch-A#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/4, Gi1/5
Gi1/6, Gi1/7, Gi1/8, Gi1/9
Gi1/10, Gi1/11, Gi1/12, Gi1/13
Gi1/14, Gi1/15, Gi1/16, Gi1/17
Gi1/18, Gi1/19, Gi1/20, Gi1/21
Gi1/22, Gi1/23, Gi1/24, Gi1/25
Gi1/26, Gi1/27, Gi1/28, Gi1/29
Gi1/30, Gi1/31, Gi1/32, Gi1/33
Gi1/34, Gi1/35, Gi1/36, Gi1/37
Gi1/38, Gi1/39, Gi1/40, Gi1/41
Gi1/42, Gi1/43, Gi1/44, Gi1/45
Gi1/46, Gi1/47, Gi1/48, Te3/2
Te3/3, Te3/4, Te3/5, Te3/6
Te3/7, Te3/8
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
Switch-A#
Switch-C#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 503d.e583.3b40
Configuration last modified by 10.122.190.227 at 11-24-22 13:44:22
Local updater ID is 10.122.190.227 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 4
MD5 digest : 0xCB 0x67 0x2A 0xF1 0x9A 0x8D 0xD3 0x1B
0xA8 0xB3 0x89 0xB2 0x32 0x63 0xA6 0xD0
Switch-C#
Switch-C#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/3, Gi1/4
Gi1/5, Gi1/6, Gi1/7, Gi1/8
Gi1/9, Gi1/10, Gi1/11, Gi1/12
Gi1/13, Gi1/14, Gi1/15, Gi1/16
Gi1/17, Gi1/18, Gi1/19, Gi1/20
Gi1/21, Gi1/22, Gi1/23, Gi1/24
Gi1/25, Gi1/26, Gi1/27, Gi1/28
Gi1/29, Gi1/30, Gi1/31, Gi1/32
Gi1/33, Gi1/34, Gi1/35, Gi1/36
Gi1/37, Gi1/38, Gi1/39, Gi1/40
Gi1/41, Gi1/42, Gi1/43, Gi1/44
Gi1/45, Gi1/46, Gi1/47, Gi1/48
Te3/2, Te3/3, Te3/4, Te3/5
Te3/6, Te3/7, Te3/8
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
6 VLAN0006 active
7 VLAN0007 active
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
8 VLAN0008 active
9 VLAN0009 active
10 VLAN0010 active
11 VLAN0011 active
12 VLAN0012 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
Switch-C#
Switch-A#
Switch-A#configure terminal
Switch-A(config)#vtp version 2
Switch-A(config)#vtp mode client
Setting device to VTP Client mode for VLANS.
Switch-A(config)#end
Switch-A#
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.226 at 11-25-22 02:34:10
Feature VLAN:
--------------
VTP Operating Mode : Client
Maximum VLANs supported locally : 1005
Number of existing VLANs : 5
Configuration Revision : 1
MD5 digest : 0xD2 0x3F 0x31 0x25 0x6D 0xD1 0x3E 0x27
0x62 0x77 0x7C 0xAF 0x0F 0xF6 0x72 0x02
Switch-A#
-
En esta etapa, se creó manualmente una conexión troncal entre los dos switches. Vea cómo se sincronizan y observe el intercambio de paquetes VTP:
Switch-A#debug sw-vlan vtp events
vtp events debugging is on
Switch-A#debug sw-vlan vtp packets
vtp packets debugging is on
Switch-A#
Switch-A#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch-A(config)#interface tenGigabitEthernet3/2
Switch-A(config-if)#no shut
Switch-A(config-if)#end
Switch-A#
-
El Switch-C envía una publicación de resumen al switch-A. El Switch-A luego obtiene el nombre de dominio del VTP, como se muestra en este ejemplo de resultado:
!--- On Switch-A:
*Nov 25 02:45:46.580: VTP LOG RUNTIME: switchport trunk mode on Te3/2 has changed
*Nov 25 02:45:46.580: VTP LOG RUNTIME: delaying first flood on new trunk
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Summary packet received in NULL domain state
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Summary packet received, domain = test, rev = 4, followers = 0, length 80, trunk Te3/2
!--- This indicates that Switch-A has received its first summary advertisement.
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Validate TLVs : #tlvs 1, max blk size 4
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Validate TLVs : #00, val 6, len 4
*Nov 25 02:45:51.100:
*Nov 25 02:45:51.100: summary: 02 01 00 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.100: summary: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.100: summary: 00 00 00 00 00 00 00 04 0A 7A BE E3 32 32 31 31 .........z>c2211
*Nov 25 02:45:51.100: summary: 32 34 31 34 30 31 31 35 8D 07 FE 82 E5 FE 49 AD 24140115..~.e~I-
*Nov 25 02:45:51.100: summary: 1A 6E A5 AB D0 35 C2 CA 00 00 00 01 06 01 00 02 .n%+P5BJ........
*Nov 25 02:45:51.100:
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Transitioning from NULL to test domain
!--- This is where Switch-A gets the VTP domain name.
-
Con la depuración habilitada, puede ver que el Switch-A recibe un anuncio de resumen sin seguidores. Por lo tanto, Switch-A actualiza su nombre de dominio y envía solicitudes de anuncios para obtener la información de la VLAN, como se muestra en este ejemplo de salida:
!--- On Switch-A
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Summary packet rev 4 greater than domain test rev 0
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Domain test currently not in updating state
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Summary packet with followers field zero
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Transmit vtp request, domain test, start value 0
!--- This is where the advertisement request is sent.
-
El switch C envía otro anuncio de resumen con seguidores de campo a la VLAN 1. El anuncio de subconjunto que contiene todas las VLAN se muestra en esta salida. Luego, el Switch-A configura todas las VLAN:
!--- On Switch-A:
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Summary packet received, domain = test, rev = 4, followers = 1, length 80, trunk Te3/2
!--- Switch-A has received its second summary advertisement.
!--- This configuration revision is higher than that on Switch-A.
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Validate TLVs : #tlvs 1, max blk size 4
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Validate TLVs : #00, val 6, len 4
*Nov 25 02:45:51.595:
*Nov 25 02:45:51.596: summary: 02 01 01 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.596: summary: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.596: summary: 00 00 00 00 00 00 00 04 0A 7A BE E3 32 32 31 31 .........z>c2211
*Nov 25 02:45:51.596: summary: 32 34 31 34 30 31 31 35 8D 07 FE 82 E5 FE 49 AD 24140115..~.e~I-
*Nov 25 02:45:51.596: summary: 1A 6E A5 AB D0 35 C2 CA 00 00 00 01 06 01 00 02 .n%+P5BJ........
*Nov 25 02:45:51.596:
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Summary packet rev 4 greater than domain test rev 0
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Domain test currently not in updating state
*Nov 25 02:45:51.596: VTP LOG RUNTIME: pdu len 80, #tlvs 1
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Subset packet received, domain = test, rev = 4, seq = 1, length = 420
!--- Switch-A has received its subset advertisement.
*Nov 25 02:45:51.596: subset: 02 02 01 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.596: subset: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.596: subset: 00 00 00 00 00 00 00 04 14 00 01 07 00 01 05 DC ...............\
*Nov 25 02:45:51.596: subset: 00 01 86 A1 64 65 66 61 75 6C 74 00 14 00 01 08 ...!default.....
*Nov 25 02:45:51.596: subset: 00 02 05 DC 00 01 86 A2 56 4C 41 4E 30 30 30 32 ...\..."VLAN0002
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 03 05 DC 00 01 86 A3 56 4C 41 4E .......\...#VLAN
*Nov 25 02:45:51.596: subset: 30 30 30 33 14 00 01 08 00 04 05 DC 00 01 86 A4 0003.......\...$
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 30 34 14 00 01 08 00 05 05 DC VLAN0004.......\
*Nov 25 02:45:51.596: subset: 00 01 86 A5 56 4C 41 4E 30 30 30 35 14 00 01 08 ...%VLAN0005....
*Nov 25 02:45:51.596: subset: 00 06 05 DC 00 01 86 A6 56 4C 41 4E 30 30 30 36 ...\...&VLAN0006
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 07 05 DC 00 01 86 A7 56 4C 41 4E .......\...'VLAN
*Nov 25 02:45:51.596: subset: 30 30 30 37 14 00 01 08 00 08 05 DC 00 01 86 A8 0007.......\...(
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 30 38 14 00 01 08 00 09 05 DC VLAN0008.......\
*Nov 25 02:45:51.596: subset: 00 01 86 A9 56 4C 41 4E 30 30 30 39 14 00 01 08 ...)VLAN0009....
*Nov 25 02:45:51.596: subset: 00 0A 05 DC 00 01 86 AA 56 4C 41 4E 30 30 31 30 ...\...*VLAN0010
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 0B 05 DC 00 01 86 AB 56 4C 41 4E .......\...+VLAN
*Nov 25 02:45:51.596: subset: 30 30 31 31 14 00 01 08 00 0C 05 DC 00 01 86 AC 0011.......\...,
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 31 32 18 00 02 0C 03 EA 05 DC VLAN0012.....j.\
*Nov 25 02:45:51.596: subset: 00 01 8A 8A 66 64 64 69 2D 64 65 66 61 75 6C 74 ....fddi-default
*Nov 25 02:45:51.596: subset: 30 00 03 0D 03 EB 11 78 00 01 8A 8B 74 72 63 72 0....k.x....trcr
*Nov 25 02:45:51.596: subset: 66 2D 64 65 66 61 75 6C 74 00 00 00 01 01 0C CC f-default......L
*Nov 25 02:45:51.596: subset: 04 01 03 ED 07 01 00 02 08 01 00 07 09 01 00 07 ...m............
*Nov 25 02:45:51.596: subset: 20 00 04 0F 03 EC 05 DC 00 01 8A 8C 66 64 64 69 ....l.\....fddi
*Nov 25 02:45:51.596: subset: 6E 65 74 2D 64 65 66 61 75 6C 74 00 03 01 00 01 net-default.....
*Nov 25 02:45:51.596: subset: 24 00 05 0D 03 ED 11 78 00 01 8A 8D 74 72 62 72 $....m.x....trbr
*Nov 25 02:45:51.596: subset: 66 2D 64 65 66 61 75 6C 74 00 00 00 02 01 00 0F f-default.......
*Nov 25 02:45:51.596: subset: 03 01 00 02 ....
*Nov 25 02:45:51.596:
*Nov 25 02:45:51.666: VTP LOG RUNTIME: Transmit vtp summary, domain test, rev 4, followers 1, tlv blk size 8 (inc #tlv field),
MD5 digest calculated = 8D 07 FE 82 E5 FE 49 AD 1A 6E A5 AB D0 35 C2 CA
-
En este momento, los dos switches están sincronizados:
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.227 at 11-24-22 14:01:15
Feature VLAN:
--------------
VTP Operating Mode : Client
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 4
MD5 digest : 0x8D 0x07 0xFE 0x82 0xE5 0xFE 0x49 0xAD
0x1A 0x6E 0xA5 0xAB 0xD0 0x35 0xC2 0xCA
Switch-A#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/4, Gi1/5
Gi1/6, Gi1/7, Gi1/8, Gi1/9
Gi1/10, Gi1/11, Gi1/12, Gi1/13
Gi1/14, Gi1/15, Gi1/16, Gi1/17
Gi1/18, Gi1/19, Gi1/20, Gi1/21
Gi1/22, Gi1/23, Gi1/24, Gi1/25
Gi1/26, Gi1/27, Gi1/28, Gi1/29
Gi1/30, Gi1/31, Gi1/32, Gi1/33
Gi1/34, Gi1/35, Gi1/36, Gi1/37
Gi1/38, Gi1/39, Gi1/40, Gi1/41
Gi1/42, Gi1/43, Gi1/44, Gi1/45
Gi1/46, Gi1/47, Gi1/48, Te3/3
Te3/4, Te3/5, Te3/6, Te3/7
Te3/8
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
6 VLAN0006 active
7 VLAN0007 active
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
8 VLAN0008 active
9 VLAN0009 active
10 VLAN0010 active
11 VLAN0011 active
12 VLAN0012 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
Ejemplo 2:
En el siguiente ejemplo, se muestra cómo verificar la configuración VTP en un Catalyst 6000 que ejecuta Cisco IOS Software:
Switch#show vtp status
VTP Version: 2
Configuration Revision: 247
Maximum VLANs supported locally: 1005
Number of existing VLANs: 33
VTP Operating Mode: Client
VTP Domain Name: Lab_Network
VTP Pruning Mode: Enabled
VTP V2 Mode: Disabled
VTP Traps Generation: Disabled
MD5 digest: 0x45 0x52 0xB6 0xFD 0x63 0xC8 0x49 0x80
Configuration last modified by 0.0.0.0 at 8-12-99 15:04:49
Switch#
Ejemplo 3:
En el siguiente ejemplo, se muestra cómo mostrar las estadísticas VTP en un Catalyst 6000 que ejecuta Cisco IOS Software:
Switch#show vtp counters
VTP statistics:
Summary advertisements received: 7
Subset advertisements received: 5
Request advertisements received: 0
Summary advertisements transmitted: 997
Subset advertisements transmitted: 13
Request advertisements transmitted: 3
Number of config revision errors: 0
Number of config digest errors: 0
Number of V1 summary errors: 0
VTP pruning statistics:
Trunk Join Transmitted Join Received Summary advts received
from on-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Fa5/8 43071 42766 5
Resolver problemas el VTP
Consulte Configure VLAN Trunk Protocol (VTP) para obtener información para resolver problemas de VTP.
Nota: Solo los usuarios registrados de Cisco pueden acceder al sitio, las herramientas y los documentos internos.
Información Relacionada