Table Of Contents
database (ccn reporting historical)
db-hostname (ccn subsystem edbs dbprofile)-IVR Only
dbname (ccn subsystem edbs dbprofile)-IVR Only
db-password (ccn subsystem edbs dbprofile)-IVR Only
db-port (ccn subsystem edbs dbprofile)-IVR Only
dbtype (ccn subsystem edbs dbprofile)-IVR Only
db-username (ccn subsystem edbs dbprofile)-IVR Only
default (ccn reporting historical)
default (ccn subsystem edbs dbprofile)-IVR Only
default (ccn subsystem fax)-IVR Only
default (ccn trigger http)-IVR Only
default ccm-manager (ccn subsystem jtapi)
default ctiport (ccn subsystem jtapi)
default gateway (ccn subsystem sip)
default security password length min
default security pin length min
default-from (ccn subsystem fax)-IVR Only
description (ccn reporting historical)
D
Last Updated: June 19, 2007
database (ccn reporting historical)
db-hostname (ccn subsystem edbs dbprofile)-IVR Only
dbname (ccn subsystem edbs dbprofile)-IVR Only
db-password (ccn subsystem edbs dbprofile)-IVR Only
db-port (ccn subsystem edbs dbprofile)-IVR Only
dbtype (ccn subsystem edbs dbprofile)-IVR Only
db-username (ccn subsystem edbs dbprofile)-IVR Only
default (ccn reporting historical)
default (ccn subsystem edbs dbprofile)-IVR Only
default (ccn subsystem fax)-IVR Only
default (ccn trigger http)-IVR Only
default ccm-manager (ccn subsystem jtapi)
default ctiport (ccn subsystem jtapi)
default gateway (ccn subsystem sip)
default security password length min
default security pin length min
default-from (ccn subsystem fax)-IVR Only
description (ccn reporting historical)
database (ccn reporting historical)
To configure the Cisco Unity Express IVR reporting historical local database, use the database local command in Cisco Unity Express IVR reporting historical configuration mode. Use the no form of this command to remove the database configuration.
database local
no database local
Syntax Description
This command has no arguments or keywords.
Command Default
The Cisco Unity Express IVR reporting historical database is set up as a local database by default.
Command Modes
Cisco Unity Express IVR reporting historical configuration
Command History
Examples
The following example configures the Cisco Unity Express IVR reporting historical local database:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn reporting historicalse-10-0-0-0(config-hrdm)# database localse-10-0-0-0(config-hrdm)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionDisplays the Cisco Unity Express IVR reporting historical database configuration settings.
db-hostname (ccn subsystem edbs dbprofile)-IVR Only
To configure the hostname for the Cisco Unity Express IVR enterprise database subsystem (EDBS), use the db-hostname command in Cisco Unity Express IVR EDBS configuration mode. To change the hostname to the default hostname, use the no form of this command.
db-hostname hostname
no db-hostname hostname
Syntax Description
Defaults
The default is the IP address of the Cisco Unity Express IVR module.
Command Modes
Cisco Unity Express IVR EDBS configuration
Command History
Usage Guidelines
The hostname value identifies the Cisco Unity Express IVR module. The default value is the IP address of the module.
Note Cisco Unity Express uses the hostname value in the Cisco Unity Express IVR module prompt.
Examples
The following example changes the hostname of the module to myHost and then restores the default hostname:
se-10-0-0-0# config tse-10-0-0-0(config)# db-hostname myHostmybranch(config)# no db-hostname myHostse-10-0-0-0(config)#Related Commands
dbname (ccn subsystem edbs dbprofile)-IVR Only
To specify a Cisco Unity Express IVR enterprise database subsystem (EDBS) name, use the dbname command in Cisco Unity Express IVR EDBS profile configuration mode. To delete the database name, use the no form of this command.
dbname external-db-name
no dbname external-db-name
Syntax Description
Command Default
There is no default database name.
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
After the ccn subsystem edbs dbprofile command is successfully performed, the dbname command is used to specify the name of the external database. If this name is not specified, the Java Database Connectivity (JDBC) driver uses the default database to connect. If you specify a name, the JDBC driver connects to the external database of that name.
Examples
The following example configures the optional database name:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# dbname atlantase-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exitRelated Commands
db-password (ccn subsystem edbs dbprofile)-IVR Only
To configure the password for the Cisco Unity Express IVR enterprise database subsystem (EDBS), use the db-password command in Cisco Unity Express IVR EDBS configuration mode. To remove the password, use the no form of this command.
db-password password
no db-password password
Syntax Description
Defaults
None
Command Modes
Cisco Unity Express IVR EDBS configuration
Command History
Usage Guidelines
When you configure a password you must also configure a username by using the db-username command.
Examples
The following example sets the password of the module:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# db-username Jamesse-10-0-0-0(config-dbprof)# db-password dbpasswdse-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionConfigures the username for the Cisco Unity Express IVR EDBS.
Displays the Cisco Unity Express IVR Enterprise database profile settings.
db-port (ccn subsystem edbs dbprofile)-IVR Only
To specify the Cisco Unity Express IVR enterprise database subsystem (EDBS) port number, use the optional db-port command in Cisco Unity Express IVR EDBS profile configuration mode. To delete the database port number, use the no form of this command.
db-port port-number
no db-port port-number
Syntax Description
port-number
(Optional) Port number other than the default port number for the Cisco Unity Express IVR EDBS.
Command Default
None
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
After the ccn subsystem edbs dbprofile command is successfully performed, use the optional db-port command to specify a port number other than the default port number of the database. Although databases are typically started using their default port numbers, the default port number might have been changed to a different port number. If the port number is some number other than the default port number, you must use the db-port command to specify this port number; otherwise, there is no need to use this command.
Examples
The following example configures the Cisco Unity Express IVR EDBS to use port number 10:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# db-port 10se-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exitRelated Commands
dbtype (ccn subsystem edbs dbprofile)-IVR Only
To configure the Cisco Unity Express IVR enterprise database subsystem (EDBS) type, use the dbtype command to set the database type in Cisco Unity Express IVR EDBS profile configuration mode. To delete a database type, use the no form of this command.
dbtype {DB2 | MSSQL-MSDE | ORACLE | SYBASE}
no dbtype {DB2 | MSSQL-MSDE | ORACLE | SYBASE}
Syntax Description
Command Default
No database type is configured.
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
After the ccn subsystem edbs dbprofile command is successfully performed, the dbtype command is used to set the database type as DB2, MSSQ-MSDE, Oracle, or Sybase. The dbtype command is required.
Examples
The following example sets the database type to be Sybase:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# dbtype sybasese-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exit
Related Commands
db-username (ccn subsystem edbs dbprofile)-IVR Only
To specify the required username for connecting to the Cisco Unity Express IVR enterprise database subsystem (EDBS), use the db-username command in Cisco Unity Express IVR EDBS profile configuration mode. To delete the specified username and password strings, use the no form of this command.
db-username userid
no db-username userid
Syntax Description
Command Default
No username is configured.
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
When you configure a username you must also configure a password by using the db-password command.
Examples
The following example configures the database profile username and password:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# db-username Jamesse-10-0-0-0(config-dbprof)# db-password dbpasswdse-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionConfigures the password for the Cisco Unity Express IVR EDBS.
Displays the Cisco Unity Express IVR EDBS profile settings.
default (ccn application)
To reset a CCN application parameter to its default value, use the default command in CCN application configuration mode.
default {description | enabled | maxsessions | parameter name}
Syntax Description
Command Modes
CCN application configuration
Command History
Usage Guidelines
The default command sets a Cisco Unified Communication Network (CCN) application parameter to its default value.
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn application voicemail
se-10-0-0-0(config-application)# default maxsessionsse-10-0-0-0(config-application)# endse-10-0-0-0(config)# exitRelated Commands
default (ccn engine)
To set the upper limit on the number of steps executed in a CCN application to the default value, use the default command in CCN engine configuration mode.
default maxsteps
Syntax Description
Command Modes
CCN engine configuration mode
Command History
Examples
The following example resets the specified parameters to their factory values:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn engine
se-10-0-0-0(config-engine)# default maxstepsse-10-0-0-0(config-engine)# end
se-10-0-0-0(config)# exitRelated Commands
default (ccn reporting historical)
To reset the values for the Cisco Unity Express IVR reporting historical database to their default values, use the default command in Cisco Unity Express IVR reporting historical configuration mode.
default {database | description | enabled | purge}
Syntax Description
Command Default
The default is the hostname of the Cisco Unity Express system.
Command Modes
Cisco Unity Express IVR reporting historical configuration
Command History
Usage Guidelines
To allow the database server to differentiate data for every Cisco Unity Express IVR system that saves historical data to the same database, create a descriptive name for the Cisco Unity Express IVR historical database.
Examples
The following example resets the Cisco Unity Express IVR reporting historical database parameters to their default values:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn reporting historicalse-10-0-0-0(config-hrdm)# default database localse-10-0-0-0(config-hrdm)# default descriptionse-10-0-0-0(config-hrdm)# default enabledse-10-0-0-0(config-hrdm)# default purgese-10-0-0-0(config-hrdm)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionDisplays the Cisco Unity Express IVR reporting historical database configuration settings.
default (ccn subsystem edbs dbprofile)-IVR Only
To reset the Cisco Unity Express IVR enterprise database subsystem (EDBS) values to their default values, use the default command in Cisco Unity Express IVR EDBS profile configuration mode.
default {credentials | dbname | dbtype | description | enabled | db-hostname | maxactive | parameter | db-password | db-port | db-username}
Syntax Description
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
After entering the ccn subsystem edbs profile command, use the default command to reset the database values to their default values.
Examples
The following example resets the Cisco Unity Express IVR EDBS values to their default values:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# default credentialsse-10-0-0-0(config-dbprof)# default dbnamese-10-0-0-0(config-dbprof)# default dbtypese-10-0-0-0(config-dbprof)# default descriptionse-10-0-0-0(config-dbprof)# default enabledse-10-0-0-0(config-dbprof)# default db-hostnamese-10-0-0-0(config-dbprof)# default maxactivese-10-0-0-0(config-dbprof)# default parameterse-10-0-0-0(config-dbprof)# default db-passwordse-10-0-0-0(config-dbprof)# default db-portse-10-0-0-0(config-dbprof)# default db-usernamese-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exit
Related Commands
default (ccn subsystem fax)-IVR Only
To delete the fax default-from e-mail address of the Cisco Unity Express IVR fax application, use the default command in Cisco Unity Express IVR fax configuration mode.
default default-from email-address-string
Syntax Description
Command Default
None
Command Modes
Cisco Unity Express IVR fax configuration
Command History
Examples
This example removes the Cisco Unity Express IVR fax default-from e-mail address of the fax application:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem faxse-10-0-0-0(config-fax)# default default from name@domain.comse-10-0-0-0(config-fax)# endse-10-0-0-0(config)# exitRelated Commands
default (ccn trigger http)-IVR Only
To reset the Cisco Unity Express IVR HTTP trigger values to their default values, use the default command in Cisco Unity Express IVR HTTP trigger configuration mode.
default {application | enabled | idletimeout | locale | maxsessions}
Syntax Description
Command Modes
Cisco Unity Express IVR HTTP trigger configuration
Command History
Usage Guidelines
After the ccn trigger http command is successfully performed, use the default command to reset the HTTP trigger values to their default values.
Examples
The following example resets the Cisco Unity Express IVR HTTP-based trigger values to their default values:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger httpse-10-0-0-0(config-trigger)# default applicationse-10-0-0-0(config-trigger)# default enabledse-10-0-0-0(config-trigger)# default idletimeoutse-10-0-0-0(config-trigger)# default localese-10-0-0-0(config-trigger)# default maxsessionsse-10-0-0-0(config-trigger)# endse-10-0-0-0(config)# exit
Related Commands
Command DescriptionDisplays the trigger and application settings. Use the show ccn trigger http command option to display the Cisco Unity Express IVR HTTP-based trigger settings.
default (ccn trigger jtapi)
To reset a CCN JTAPI trigger parameter to its default value, use the default command in CCN trigger JTAPI configuration mode. To disable the trigger or to set the number of maxsessions to 0, use the no form of this command.
default {application | enabled | idletimeout | locale | maxsessions}
no default {enabled | maxsessions}
Syntax Description
Command Modes
CCN trigger JTAPI configuration
Command History
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger jtapi phonenumber 1234
se-10-0-0-0(config-trigger)# default maxsessionsse-10-0-0-0(config-trigger)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionConfigures the CCN applications, such as voice mail and auto attendant.
Configures the parameters used by all CCN applications.
Displays all of the CCN application details.
default (ccn trigger sip)
To reset a CCN SIP trigger parameter to its default value, use the default command in CCN trigger SIP configuration mode. To disable the trigger or to set the number of maxsessions to 0, use the no form of this command.
default {application | enabled | idletimeout | locale | maxsessions}
no default {enabled | maxsessions}
Syntax Description
Command Modes
CCN trigger SIP configuration
Command History
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger sip phonenumber 1234
se-10-0-0-0(config-trigger)# default maxsessionsse-10-0-0-0(config-trigger)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionConfigures the CCN applications, such as voice mail and auto attendant.
Configures the parameters used by all CCN applications.
Displays all of the CCN application details.
default ccm-manager (ccn subsystem jtapi)
To reset a Cisco Unified Communications Manager JTAPI subsystem parameter used by Cisco Unity Express to its default value, use the default ccm-manager command in Cisco Unity Express CCN subsystem JTAPI configuration mode.
default ccm-manager {address | username | password}
Syntax Description
Command Modes
CCN subsystem JTAPI configuration
Command History
Examples
The following example sets the Cisco Unified Communications Manager server address to 0.0.0.0.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem jtapi
se-10-0-0-0(config-jtapi)# default ccm-manager addressse-10-0-0-0(config-jtapi)# end
se-10-0-0-0(config)# exitRelated Commands
default ctiport (ccn subsystem jtapi)
To reset the Cisco Unified Communications Manager CTI port address to its default value (an empty string), use the default ctiport command in Cisco Unity Express CCN subsystem JTAPI configuration mode.
default ctiport
Syntax Description
This command has no arguments or keywords.
Command Modes
CCN subsystem JTAPI configuration
Command History
Examples
The following example sets the Cisco Unified Communications Manager CTI port address to an empty string.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem jtapi
se-10-0-0-0(config-jtapi)# default ctiportse-10-0-0-0(config-jtapi)# end
se-10-0-0-0(config)# exitRelated Commands
default gateway (ccn subsystem sip)
To reset a SIP server parameter to its default value, use the default gateway command in Cisco Unity Express CCN subsystem SIP configuration mode.
default gateway {address | port}
Syntax Description
Command Modes
CCN subsystem SIP configuration
Command History
Examples
The following example sets the SIP server port to 5060.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem sip
se-10-0-0-0(config-sip)# default gateway portse-10-0-0-0(config-sip)# end
se-10-0-0-0(config)# exitRelated Commands
default security password length min
To set the length of the security password to the default minimum, use the default security password length min command in Cisco Unity Express configuration mode.
default security password length min
Syntax Description
This command has no arguments or keywords.
Defaults
The password length is 3.
Command Modes
Cisco Unity Express configuration
Command History
Examples
The following example resets the password length:
se-10-0-0-0# config tse-10-0-0-0(config)# default security password length minse-10-0-0-0(config)# endRelated Commands
Command Descriptionsecurity password
Configures the system-wide password length and expiry time.
show security detail
Displays the password and PIN settings.
default security pin length min
To set the length of the security PIN to the default minimum, use the default security pin length min command in Cisco Unity Express configuration mode.
default security pin length min
Syntax Description
This command has no arguments or keywords.
Defaults
The PIN length is 3.
Command Modes
Cisco Unity Express configuration
Command History
Examples
The following example resets the PIN length:
se-10-0-0-0# config tse-10-0-0-0(config)# default security pin length minse-10-0-0-0(config)# endRelated Commands
Command Descriptionsecurity pin
Configures the system-wide pin length and expiry time.
show security detail
Displays the password and PIN settings.
default-from (ccn subsystem fax)-IVR Only
To configure the default-from address for the Cisco Unity Express IVR fax application, use the default-from command in Cisco Unity Express IVR fax configuration mode. Use the no form of this command to delete the default-from address.
default-from email-address-string
no default-from email-address-string
Syntax Description
Command Modes
Cisco Unity Express IVR fax configuration
Command History
Usage Guidelines
Enter a valid e-mail address string that is capable of receiving e-mail deliveries. This address must also be capable of receiving notifications of delivery failures.
Examples
The following example resets the fax default-from e-mail address:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem fax
se-10-0-0-0(config-fax)# default-from name@domain.comse-10-0-0-0(config-fax)# endse-10-0-0-0(config)# exit
Related Commands
description (ccn application)
To specify an optional description for a CCN application, use the description command in Cisco Unity Express CCN application configuration mode. To remove the description, use the no form of this command.
description "text"
no description "text"
Syntax Description
Defaults
No string is defined.
Command Modes
CCN application configuration
Command History
Examples
The following example adds a description for the CCN autoattendant application:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn application autoattendant
se-10-0-0-0(config-application)# description "Release 1 AA"
se-10-0-0-0(config-application)# end
se-10-0-0-0(config)# exitRelated Commands
Command DescriptionConfigures the CCN applications, such as voice mail and auto attendant.
Displays the CCN application details.
description (ccn reporting historical)
To create a descriptive name for the Cisco Unity Express IVR reporting historical database, use the optional description command in Cisco Unity Express IVR reporting historical configuration mode. Use the no form of this command to set the description to the configured hostname of the system.
description word
no description word
Syntax Description
Command Default
Hostname of the Cisco Unity Express system.
Command Modes
Cisco Unity Express IVR reporting historical configuration
Command History
Usage Guidelines
Allows the database server to differentiate data among multiple Cisco Unity Express systems that save historical data to the same database, create a descriptive name for the Cisco Unity Express historical database.
Examples
The following example creates a database description for the Cisco Unity Express IVR reporting historical database:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn reporting historicalse-10-0-0-0(config-hrdm)# description cue-192-1-2-11se-10-0-0-0(config-hrdm)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionDisplays the Cisco Unity Express IVR reporting historical database configuration settings.
dtmf-relay
To set the SIP DTMF relay mechanism, use the dtmf-relay command in Cisco Unity Express SIP configuration mode. To use the default values, use the no or default form of this command.
dtmf-relay {rtp-nte | sub-notify | info | sip-notify}
no dtmf-relay
default dtmf-relay
Syntax Description
Defaults
sip-notify, sub-notify is the default combination.
Command Modes
Cisco Unity Express SIP configuration
Command History
Usage Guidelines
To use the rtp-nte option, verify that the Cisco IOS SIP gateway is configured to use Unsolicited NOTIFY for SIP calls, as shown in the following example:
dial-peer voice 1000 voipdestination-pattern 6700session protocol sipv2session target ipv4:10.100.9.6dtmf-relay sip-notify rtp-ntecodec g711ulawno vadTo use the sip-notify option, verify that the Cisco IOS SIP gateway is configured to use Unsolicited NOTIFY for SIP calls, as shown in the following example:
dial-peer voice 1 voipdestination-pattern 6700session protocol sipv2session target ipv4:10.100.9.6dtmf-relay sip-notifycodec g711ulawno vadConfigure more than one option for transferring DTMF signals. The order in which you configure the options determines their order of preference. To configure more than one signal option, specify them using a single dtmf-relay command.
Table 2 shows the various option combinations, the remote end capability, and the signaling option for incoming and outgoing DTMF signals.
Table 2 DTMF Relay Option Combinations
Cisco Unity Express Configuration Option Supported at Remote End Option Used for Incoming DTMF to Cisco Unity Express Option Used for Outgoing DTMF from Cisco Unity Expresssub-notify
—
sub-notify
no DTMF
info
—
no DTMF
info
rtp-nte
rtp-nte
rtp-nte
rtp-nte
sip-notify
sip-notify
sip-notify
sip-notify
sip-notify, rtp-nte
rtp-nte, sip-notify
sip-notify1
sip-notify1
sip-notify, rtp-nte
rtp-nte
rtp-nte
rtp-nte
sip-notify, info
sip-notify
sip-notify
sip-notify
sip-notify, info
no support2
no DTMF
info
sip-notify, sub-notify
sip-notify
sip-notify
sip-notify
sip-notify, sub-notify
no support2
sub-notify
sub-notify
sip-notify, rtp-nte, info
rtp-nte
rtp-nte
rtp-nte
sip-notify, rtp-nte, info
sip-notify
sip-notify
sip-notify
sip-notify, rtp-nte, info
no support2
no DTMF
info
sip-notify, rtp-nte, sub-notify
rtp-nte
rtp-nte
rtp-nte
sip-notify, rtp-nte, sub-notify
sip-notify
sip-notify
sip-notify
sip-notify, rtp-nte, sub-notify
no support2
sub-notify
no DTMF
sub-notify, info
—
sub-notify
info
rtp-nte, sub-notify
rtp-nte
rtp-nte
rtp-nte
rtp-nte, sub-notify
no support2
sub-notify
no DTMF
rtp-nte, info
rtp-nte
rtp-nte
rtp-nte
rtp-nte, info
no support2
no DTMF
info
sip-notify, rtp-nte, sub-notify, info
sip-notify, rtp-nte
sip-notify
sip-notify
sip-notify, rtp-nte, sub-notify, info
rtp-nte
rtp-nte
rtp-nte
sip-notify, rtp-nte, sub-notify, info
no support2
sub-notify
info
1 For incoming call. For outgoing call, the remote end decides between rtp-nte and sip-notify.
2 No support for rtp-nte and sip-notify.
Examples
The following example configures the options sip-notify and rtp-nte for handling DTMF signals.
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem sipse-10-0-0-0(config-sip)# dtmf-relay sip-notify rtp-ntese-10-0-0-0(config-sip)# endse-10-0-0-0(config)# endse-10-0-0-0#Related Commands