Table Of Contents
Configuring Recommended Servers for Cisco Unified Personal Communicator
How to Configure Voice-Mail Servers
Configuring Cisco Unity Connection Servers
Configuring Cisco Unity Servers
Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
Configuring Secure Messaging in Cisco Unified Presence Administration
Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
Creating Voice-Mail Profiles in Cisco Unified Presence Administration
How to Configure Conferencing Servers
Configuring Cisco Unified MeetingPlace Express and Cisco Unified MeetingPlace Express VT Servers
Configuring Cisco Unified MeetingPlace Servers
Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration
Creating Conferencing Profiles in Cisco Unified Presence Administration
Configuring Videoconferencing Resources
Configuring Recommended Servers for Cisco Unified Personal Communicator
December 2008
•How to Configure Voice-Mail Servers
•How to Configure Conferencing Servers
•Configuring Videoconferencing Resources
Note Make sure you first complete the tasks in Chapter 2, "Configuring Required Servers for Cisco Unified Personal Communicator." After you complete the tasks in this chapter, Cisco Unified Personal Communicator has full feature support for voice mail, web conferencing, and videoconferencing.
How to Configure Voice-Mail Servers
•Configuring Cisco Unity Connection Servers
•Configuring Cisco Unity Servers
•Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
•Configuring Secure Messaging in Cisco Unified Presence Administration
•Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Configuring Cisco Unity Connection Servers
Cisco Unity Connection provides Cisco Unified Personal Communicator users with the ability to view, play, sort, and delete voice-mail messages from within the Cisco Unified Personal Communicator application.
Before You Begin
•Install and configure Cisco Unified Communications Manager. For details, see the installation and upgrade guides, and maintain and operate guides at the following URL:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/tsd_products_support_series_home.html
•Install and configure a supported release of Cisco Unity Connection.
–For details about the server installation:
http://www.cisco.com/en/US/products/ps6509/prod_installation_guides_list.html
–For details about supported Cisco Unity Connection releases, see the Cisco Unified Personal Communicator release notes:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
•Integrate Cisco Unified Communications Manager and Cisco Unity Connection. Both servers must be installed and running to configure voice-mail ports. For details about the voice-mail configuration, see the Cisco Unified Communications Manager Administration Guide:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
Procedure
Step 1 Set up a new or existing class of service in Cisco Unity Connection Administration to enable Internet Mail Access Protocol (IMAP) client access to voice messages.
a. Expand Class of Service in the left pane.
b. Click Class of Service.
c. Click the display name of the applicable class of service in the Search Results table, in the Search Class of Service window.
d. Check Allow Users to Use Unified Client to Access Voice Mail for port 7993 and TLS, under Features.
e. For all other ports and protocols, perform the following steps:
–Check Allow Users to Access VoiceMail Using an IMAP Client under Licensed Features.
–Select Allow Users to Access Message Bodies.
–Check Allow Users to Use Unified Client to Access Voice Mail under Features.
f. Click Save.
Step 2 Configure the user:
•If the users are existing Cisco Unity Connection users, add them to the Cisco Unified Communications Manager database and to Cisco Unified Presence. Proceed to Step 4.
•If the user is a new Cisco Unified Personal Communicator user, add the user to Cisco Unified Communications Manager database, Cisco Unity Connection, and to Cisco Unified Presence.
See the administration guides for Cisco Unified Communications Manager and Cisco Unified Presence at the following URLs:
•http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
•http://www.cisco.com/en/US/products/ps6837/prod_maintenance_guides_list.html
Step 3 Create a Connection user account on the Cisco Unity Connection server with a voice mailbox for each Cisco Unified Personal Communicator user.
The user ID in Cisco Unity Connection does not need to match the user ID in Cisco Unified Presence or in Cisco Unified Personal Communicator. Cisco Unified Personal Communicator has an independent voicemail ID, which is set in the application Preference window.
For details about setting up the account, see the Cisco Unity Connection User Moves, Adds, and Changes Guide:
http://www.cisco.com/en/US/products/ps6509/prod_maintenance_guides_list.html
Step 4 (Optional) Enable secure messaging as follows:
a. Expand Class of Service in the left pane, and then click Class of Service.
b. Select an option from Require Secure Messaging in the Message Options section to enable secure messages.
Step 5 (Optional) Specify how to handle unidentified caller message security for your users as follows:
a. Expand Users in the left pane.
b. Click Users.
c. Click the alias of a user.
d. Select Edit > Message Settings.
e. Check Mark Secure in Unidentified Callers Message Security.
Step 6 If one does not already exist, specify a web application password in Cisco Unity Connection Administration for the applicable user accounts.
For details, see the Cisco Unity Connection User Moves, Adds, and Changes Guide:
http://www.cisco.com/en/US/products/ps6509/prod_maintenance_guides_list.html
Step 7 Perform the voice-mail configuration in Cisco Unified Presence Administration.
Troubleshooting Tips
•Cisco Unified Personal Communicator users must enter their Cisco Unity Connection credentials, that is, their username and web application password, in the Cisco Unified Personal Communicator Preferences window.
•If the server can be contacted and the user credentials are correct, but voice-mail messages are not downloaded, do the following:
–Check the configuration of port 7993.
–Make sure Cisco Unified Personal Communicator is listening on port 7993.
–Check the firewall configuration. Use Telnet from a remote computer to the computer running Cisco Unified Personal Communicator, and make sure you can connect.
For details, see the Cisco Unified Personal Communicator troubleshooting guide at the following URL:
http://www.cisco.com/en/US/products/ps6844/prod_troubleshooting_guides_list.html
Related Topics
•Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
•Configuring Secure Messaging in Cisco Unified Presence Administration
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Configuring Cisco Unity Servers
Cisco Unity receives calls, plays greetings, and records and encodes voice mail. When a voice mail is received, Cisco Unity adds the .wav file to an e-mail and sends it to the configured e-mail account. Cisco Unity creates a subscriber mailbox on the Microsoft Exchange server for use as its mailstore server for message storage.
When Cisco Unified Personal Communicator users want to listen to their voice mails, they use Cisco Unified Personal Communicator to retrieve them from the mailstore server through IMAP.
Cisco Unified Personal Communicator supports both the Cisco Unity unified messaging and the Cisco Unity voice messaging configurations. With unified messaging, the Exchange server e-mail account supports both voice mail and e-mail. With voice messaging, the Exchange server e-mail account contains only voice-mail messages.
Before You Begin
•Install and configure Cisco Unified Communications Manager. For details, see the installation and upgrade guides, and maintain and operate guides at the following URL:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/tsd_products_support_series_home.html
•Install and configure a supported release of Cisco Unity.
–For details about the server installation with Microsoft Exchange, see the following URL:
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_installation_guides_list.html
–For details about supported Cisco Unity releases, see the Cisco Unified Personal Communicator release notes at the following URL:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
•Integrate Cisco Unified Communications Manager and Cisco Unity. Both servers must be installed and running to configure voice-mail ports. For details about the voice-mail configuration, see the Cisco Unified Communications Manager Administration Guide at the following URL:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
•If you plan to use SSL to provide secure transmission with the mailstore server, you must set up Cisco Unity to use SSL during the installation or upgrade (or at any time after the installation or upgrade is complete). You must designate a server to act as your certificate authority, submit a certificate request, issue the certificate, and install it on the Cisco Unity server. For details, see the security guide:
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_maintenance_guides_list.html
Procedure
Step 1 Configure the Microsoft Exchange server to use the IMAP virtual server.
For Exchange 2003, perform the following steps:
a. Select Start > All Programs > Microsoft Exchange > System Manager.
b. In the left pane of the System Manager, expand Servers.
c. Select the server name.
d. Select Protocols > IMAP.
e. Right-click, and select Start Server.
For Exchange 2007, perform the following steps:
a. Select Start > Run, enter services.msc, and click OK.
b. Select the Microsoft Exchange IMAP4 service, and click Start. This service is not started by default.
Step 2 Configure the port and encryption type.
For Exchange 2003, perform the following steps:
a. Right-click IMAP Virtual Server, and select Properties.
b. Click Authentication from the Access tab.
–Verify that Requires SSL/TLS Encryption is not checked to use TCP and SSL connection.
–Verify that Requires SSL/TLS Encryption is checked to use SSL only.
c. Click OK.
For Exchange 2007, perform the following steps:
a. Specify the authentication settings for the Client Access Server that is running the IMAP4 service through the Exchange Power Shell.
Select Start > Programs > Microsoft Exchange Server 2007 > Exchange Management Shell.
Exchange 2007 uses SSL by default.
b. Execute one of the following commands for the appropriate setting:
–For plain text login: set-imapsettings -LoginType PlainTextLogin
–For SSL: set-imapsettings -LoginType SecureLogin
Step 3 Configure the user:
•If the user is an existing Cisco Unity user, add the user to the Cisco Unified Communications Manager database and to Cisco Unified Presence.
•If the user is a new user, add the user to the Cisco Unified Communications Manager database, Cisco Unity (which adds the user to Exchange and to Active Directory), and to Cisco Unified Presence.
See the administration guides for Cisco Unified Communications Manager and Cisco Unified Presence at the following URLs:
•http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
•http://www.cisco.com/en/US/products/ps6837/prod_maintenance_guides_list.html
Step 4 Create mailboxes for new and existing users. For details, see the documentation for your Exchange server.
Step 5 (Optional) Enable secure messaging as follows:
a. Select Subscribers > Subscribers > Features to make the change on a subscriber template.
The change you make here is not applied to currently existing subscriber accounts that were created by using this template. The setting applies only to subscriber accounts that are created by using this template after the change has been made.
b. Select an option from the Message Security When Sending a Message list to enable secure messages. For example, select Encrypt All Messages.
This setting specifies whether messages are encrypted when subscribers send messages to other subscribers.
c. Click Save.
d. Repeat these steps for additional subscribers or subscriber templates, as applicable.
Step 6 (Optional) Enable secure messaging for messages from unidentified callers:
a. Select System > Configuration > Message Security Settings.
b. Specify whether messages from unidentified callers are encrypted. Select an option from the list.
c. Click Save.
Step 7 Perform the voice-mail and mailstore configuration in Cisco Unified Presence Administration.
Troubleshooting Tip
Cisco Unified Personal Communicator users must enter their Cisco Unity credentials in the Cisco Unified Personal Communicator Preferences window.
Related Topics
•Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
•Configuring Secure Messaging in Cisco Unified Presence Administration
•Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
You must configure voice-mail settings so that the Cisco Unified Presence server can interact with the voice message web service (VMWS) on Cisco Unity or Cisco Unity Connection. The VMWS service enables Cisco Unified Personal Communicator to move deleted voice-mail messages to the correct location. This service also provides message encryption capabilities to support secure messaging.
Before You Begin
•Make sure that you configure a supported server as described in the following sections:
–Configuring Cisco Unity Connection Servers
–Configuring Cisco Unity Servers
•For Cisco Unity Connection, obtain the hostname or IP address of the voice-mail server. You might need to specify more than one hostname to provide services for the number of users in your environment.
•For Cisco Unity, obtain the hostname or IP address of the Cisco Unity server. You might need to specify more than one hostname to provide services for the number of users in your environment.
•For Cisco Unity, obtain the hostnames or IP addresses of the peer Microsoft Exchange server or servers.
Procedure
Step 1 Select the following menu in Cisco Unified Presence Administration:
Release 7.0: Application > Cisco Unified Personal Communicator > Voicemail Server
Release 6.x: Application > Cisco Unified Personal Communicator > Unity Server
Step 2 Click Add New in the Find and List window to add a new server.
Step 3 Enter information into the fields, as shown in the following table:
Step 4 Click Save.
Step 5 Click Add New, and repeat this procedure for each voice-mail server in your environment.
Related Topics
•Configuring Secure Messaging in Cisco Unified Presence Administration
•Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Configuring Secure Messaging in Cisco Unified Presence Administration
To enable users to retrieve and play secure voice-mail messages from Cisco Unified Personal Communicator, you must do the following:
•Configure secure messaging in Cisco Unified Presence Administration Release 7.0
•Configure Cisco Unity to encrypt messages
Cisco Unity Connection
In Cisco Unity Connection, when a user sends a message, class-of-service settings determine the security level of the message. When a user marks a message as private, Cisco Unity Connection automatically marks the message as secure.
Cisco Unity Connection provides audio for secure voice-mail messages through a special IMAP port, port 7993. This port requires Transport Layer Security (TLS). Cisco Unified Personal Communicator uses this port to access, download, and play the secure message.
Cisco Unity
Cisco Unity uses public-key cryptography to send secure messages. Each Cisco Unity server in the network has a public key and a private key. The public key for each server is stored in the Cisco Unity database and is shared through Active Directory with other Cisco Unity servers in the network.
The Cisco Unity server generates new session keys daily. The server uses the session key to encrypt the voice mail, and to control the age of messages. Users cannot play messages that are encrypted with keys that are older than the age policy allows.
Cisco Unity uses Microsoft Exchange to store secure messages. You configure all subscriber mailboxes on these message store servers. Cisco Unified Personal Communicator connects to the message store and performs the following actions:
1. Uses IMAP to download the message from Exchange.
2. Determines if the message is encrypted.
3. If the message is not encrypted, Cisco Unified Personal Communicator plays the message.
4. If the message is encrypted, the following happens:
a. Cisco Unified Personal Communicator extracts the encrypted session keys from the .wav file for the message.
b. Cisco Unified Personal Communicator submits the keys to the Cisco Unity server.
c. The Cisco Unity server tries to decrypt the session keys. The server uses the private key certificates in the Cisco Unity database.
d. If the Cisco Unity server decrypts the session key, Cisco Unified Personal Communicator uses the key to decrypt the message, and plays the messages to the user.
e. If the Cisco Unity server cannot decrypt the session key, Cisco Unified Personal Communicator plays a decoy message to the user.
Before You Begin
Install and configure secure message features on the voice-mail servers, as follows:
•For Cisco Unity Connection, see the information in this guide on how to configure Cisco Unity Connection servers. See also the product online help, the system administration guide, and the user moves, adds, and changes guide at the following URL:
http://www.cisco.com/en/US/products/ps6509/prod_maintenance_guides_list.html
•For Cisco Unity, see the information in this guide on how to configure Cisco Unity servers. See also the product online help or the security guide for Cisco Unity with Microsoft Exchange at the following URL:
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_maintenance_guides_list.html
Restrictions
Secure message features are not available in releases of Cisco Unified Presence Administration earlier than Release 7.0.
Procedure
Step 1 Select Application > Cisco Unified Personal Communicator > Voicemail Server.
Step 2 Find and select your server.
Step 3 Perform one of the following actions, depending on what type of secure messaging you want to configure:
Related Topics
•Configuring Cisco Unity Connection Servers
•Configuring Cisco Unity Servers
•Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
•Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration
You must configure Cisco Unified Presence Release 7.0 with mailstore information so that Cisco Unified Personal Communicator can connect to the mailstore. Cisco Unified Personal Communicator uses IMAP to download messages.
Cisco Unity creates subscriber mailboxes for message storage on the Microsoft Exchange server. Cisco Unity Connection usually provides a mailstore, and hosts the mailstore on the same server.
Before You Begin
•Obtain the hostname or IP address of the mailstore server.
•If you upgrade from Release 6.x to Release 7.0, Cisco Unified Presence automatically imports the IMAP settings into the Mailstore Configuration page. In Release 6.x, these settings are on the Application > Cisco Unified Personal Communicator > Unity Server page.
Restrictions
•You must provision mailstore servers before you can add the servers to the voice-mail profiles.
Procedure
Step 1 Select Application > Cisco Unified Personal Communicator > Mailstore.
Step 2 Click Add New to add a new server.
Step 3 Enter information into the fields, as follows.
The following table describes the protocols you can use, and the security features the protocols implement for voice-mail messages:
Step 4 Click Save.
Related Topics
•Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Creating Voice-Mail Profiles in Cisco Unified Presence Administration
Before You Begin
•You must create voice-mail profiles before you can add Cisco Unified Personal Communicator licensed users to profiles.
•Specify voice-mail server names and addresses.
•Specify mailstore server names and addresses.
Restrictions
Voice-mail server failover and mailstore server failover are not supported in Cisco Unified Personal Communicator Release 7.0(1). Do not specify backup servers in the Voicemail Profile in Cisco Unified Presence Administration.
Procedure
Step 1 Select the following menu in Cisco Unified Presence Administration:
Release 7.0: Application > Cisco Unified Personal Communicator > Voicemail Profile
Release 6.x: Application > Cisco Unified Personal Communicator > Unity Profile
Step 2 Click Add New in the Find and List window.
Step 3 Enter information into the fields, as follows.
Note The fields in the window might be in a different order than listed in the table depending on the release Cisco Unified Presence.
Step 4 Click Save.
Step 5 Click Add New, and repeat this procedure for each voice-mail profile you want to create.
Related Topics
•How to Change Application Profiles, page 2-31
•Specifying Voice-Mail Server Names and Addresses in Cisco Unified Presence Administration
•Specifying Mailstore Server Names and Addresses in Cisco Unified Presence Administration.
•Changing Application Profiles for a Single User, page 2-32
How to Configure Conferencing Servers
•Configuring Cisco Unified MeetingPlace Express and Cisco Unified MeetingPlace Express VT Servers
•Configuring Cisco Unified MeetingPlace Servers
•Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration)
•Creating Conferencing Profiles in Cisco Unified Presence Administration
Configuring Cisco Unified MeetingPlace Express and Cisco Unified MeetingPlace Express VT Servers
Cisco Unified MeetingPlace Express or Cisco Unified MeetingPlace ExpressVT provide Cisco Unified Personal Communicator users with the ability to escalate to web meetings from within an existing audio or video communication session. With Cisco Unified MeetingPlace Express VT, users can move from point-to-point to multiparty voice and video calls.
Before You Begin
•Install a supported release of the web conferencing server (Cisco Unified MeetingPlace Express or Cisco Unified MeetingPlace Express VT). For details about the server installation:
http://www.cisco.com/en/US/products/ps6533/prod_installation_guides_list.html
For details about supported Cisco Unified MeetingPlace Express releases, see the release notes:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
•Integrate the web conferencing server with Cisco Unified Communications Manager. Configure call control features:
http://www.cisco.com/en/US/products/ps6533/products_installation_and_configuration_guides_list.html
•Determine the number of Cisco Unified MeetingPlace Express (or Cisco Unified MeetingPlace Express VT) user licenses that are needed to provide enough web ports for meetings initiated through Cisco Unified Personal Communicator.
Procedure
Step 1 Integrate the web conference server with Cisco Unified Personal Communicator:
For Cisco Unified MeetingPlace Express VT ad hoc conferencing functionality:
a. Install the following licenses through the Cisco Unified MeetingPlace Express Administration Center:
•adhocsystemsoftware
•webconf
•maxadhoc
This provides enough web ports for Cisco Unified Personal Communicator users. Cisco Unified Personal Communicator requires support for more than six voice, six video, and six web ports.
b. Configure Cisco Unified MeetingPlace Express VT for ad hoc conferencing by following the instructions in the configuration and maintenance guide:
http://www.cisco.com/en/US/products/ps6533/prod_maintenance_guides_list.html
For Cisco Unified MeetingPlace Express reservationless functionality:
a. Install the following licenses:
•systemsoftware
•webconf
•maxweb
This provides enough web ports for both the full web meetings that are initiated from Cisco Unified MeetingPlace Express, and the web meetings that are initiated from Cisco Unified Personal Communicator.
b. For Cisco Unified MeetingPlace Express-specific information about integrating with Cisco Unified Personal Communicator, managing certificates, creating user profiles, and configuring call-control, see the configuration and maintenance guide:
http://www.cisco.com/en/US/products/ps6533/prod_maintenance_guides_list.html
Step 2 If not already enabled, enable the Secure Sockets Layer (SSL) encryption technology on the web conference server by obtaining and uploading the required certificates from a trusted certificate authority (CA).
The certificate is required for secure communications between Cisco Unified Personal Communicator and the web conference server. Without SSL, clear text passwords are sent from Cisco Unified Personal Communicator to the web conferencing server and from the log-in browser to the web conferencing server.
Step 3 Set up a user profile on the web conference server for each Cisco Unified Personal Communicator user who might initiate web meetings from a Cisco Unified Personal Communicator conversation.
•You do not need to create a user profile for Cisco Unified Personal Communicator users who attend web meetings. They join the web meeting as guests, and a password is not needed.
•Make sure to set the Method of Attending to I'll Call In for users who might initiate web meetings; otherwise, the web conference system will try to contact the user who clicked the Escalate to Web Conference button in Cisco Unified Personal Communicator. Make sure to ask users not to change this setting.
Tip As an alternative, you can configure the Administrative XML Layer Simple Object Access Protocol (AXL SOAP) authentication on Cisco Unified Communications Manager to simplify the web conference user profile administration. With this configuration, the Cisco Unified Personal Communicator meeting initiator needs a Cisco Unified Communications Manager profile instead of a web conference user profile. With AXL authentication, when the initiator requests a meeting for the first time through Cisco Unified Personal Communicator, a web conference profile is automatically created for the initiator.
Step 4 Assist users with the Presenter Add-In installation so that desktops, documents, or computer applications can be shared. For details:
http://www.cisco.com/en/US/products/ps6533/products_user_guide_list.html
Step 5 Change the network configuration so that inbound calls from the public switched telephone network (PSTN) to Cisco Unified Personal Communicator support RFC2833.
•For inbound calls, Cisco Unified Personal Communicator requires RFC2833 support if these calls require dual tone multifrequency (DTMF) digit collection. Inbound calls to the client will not be answered with key press markup language (KPML) support.
A typical inbound call scenario is when the web conference server calls the user as a conference is being set up. In this situation, if the inbound call from the PSTN supports RFC2833, the Cisco Unified Personal Communicator user can join the meeting by using the session dial pad.
•For outbound calls, Cisco Unified Personal Communicator supports both KPML and RFC2833 digit collection.
Step 6 Perform the Cisco Unified MeetingPlace Express server-specific configuration in Cisco Unified Presence Administration.
For details about supported and unsupported Cisco Unified MeetingPlace Express meeting controls, see the release notes:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
For a description of the characteristics of a web conference that you add to a Cisco Unified Personal Communicator conversation, see the user guide for Cisco Unified Personal Communicator:
http://www.cisco.com/en/US/products/ps6844/products_user_guide_list.html
Troubleshooting Tips
Cisco Unified Personal Communicator users must enter their Cisco Unified MeetingPlace Express credentials in the Cisco Unified Personal Communicator Preferences window.
Related Topics
•Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration
•Creating Conferencing Profiles in Cisco Unified Presence Administration
Configuring Cisco Unified MeetingPlace Servers
Cisco Unified MeetingPlace provides a more extensive feature set (such as scheduled and reservationless rich-media conferencing) and allows more concurrent users than Cisco Unified MeetingPlace Express or Cisco Unified MeetingPlace Express VT. With Cisco Unified MeetingPlace, a Cisco Unified Personal Communicator user can escalate to a web conferencing session or to a video conferencing session from within an existing audio session.
Before You Begin
•Install a supported release of the web conferencing server. For details about the server installation:
http://www.cisco.com/en/US/products/sw/ps5664/ps5669/prod_installation_guides_list.html
For details about supported Cisco Unified MeetingPlace releases, see the Cisco Unified Personal Communicator release notes:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
•Integrate the web conferencing server with Cisco Unified Communications Manager. Configure call control features:
Release 7.0: http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_installation_and_configuration_guides_list.html
Release 6.x: http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_implementation_design_guides_list.html
•Determine the number of web and audio conferencing user licenses that provide enough web ports for meetings initiated through Cisco Unified MeetingPlace and through Cisco Unified Personal Communicator:
Release 7.0:
http://www.cisco.com/en/US/products/sw/ps5664/ps5669/prod_installation_guides_list.html
Release 6.x:
http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_implementation_design_guides_list.html
Procedure
Step 1 Install web and audio conferencing user licenses.
Step 2 If not already enabled, enable the Secure Sockets Layer (SSL) encryption technology on the web conference server. You must obtain and upload the required certificates from a trusted certificate authority (CA).
The certificate is required for secure communications between Cisco Unified Personal Communicator and the web conference server. Without SSL, clear text passwords are sent from Cisco Unified Personal Communicator to the web conferencing server and from the log-in browser to the web conferencing server.
For details about setting up SSL, see the web conferencing configuration guide (Release 6.x) or the configuration guide (Release 7.0):
Step 3 Set up a user authentication method on the web conference server.
The following authentication methods are supported for use with Cisco Unified Personal Communicator:
•MeetingPlace
•HTTP Basic Authentication (Domain)
•LDAP
•LDAP, then MeetingPlace
For details about configuring the authentication methods, see the web conferencing configuration guide (Release 6.x) or the configuration guide (Release 7.0):
Step 4 Set up a user profile on the Cisco Unified MeetingPlace server for each Cisco Unified Personal Communicator user who might initiate web meetings from a Cisco Unified Personal Communicator conversation.
Step 5 Perform the conferencing server configuration in Cisco Unified Presence Administration.
Troubleshooting Tips
•Cisco Unified Personal Communicator users must enter their Cisco Unified MeetingPlace credentials in the Cisco Unified Personal Communicator Preferences window. Make sure you provide the password that is consistent with the configured authentication method. For example, if you configured MeetingPlace as the authentication method, provide the user with the MeetingPlace password. If you configured LDAP as the authentication method, provide the user with the LDAP password.
•You do not need to create Cisco Unified MeetingPlace user profiles for all Cisco Unified Personal Communicator users. Cisco Unified Personal Communicator users who do not have Cisco Unified MeetingPlace profiles can attend web conferences initiated by other Cisco Unified Personal Communicator users as guests, and passwords are not needed. However, some authentication methods, for example, HTTP Basic Authentication, do not allow Cisco Unified Personal Communicator users to log in to Cisco Unified MeetingPlace as guests.
For details about the authentication methods, see the web conferencing configuration guide (Release 6.x) or the configuration guide (Release 7.0):
•If you configure multiple web servers with different authentication methods and mismatched credentials, users might have problems when they try to log in to web conferences.
Related Topics
•Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration
•Creating Conferencing Profiles in Cisco Unified Presence Administration
Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration
You must specify conferencing server names, addresses, ports, and protocol types in Cisco Unified Presence Administration so that Cisco Unified Personal Communicator can interact with them.
Before You Begin
•Make sure you configure a supported conferencing server as described in these sections:
–Configuring Cisco Unified MeetingPlace Express and Cisco Unified MeetingPlace Express VT Servers.
–Configuring Cisco Unified MeetingPlace Servers
•Obtain the hostname or IP address of the conferencing server.
Procedure
Step 1 Select the following menu in Cisco Unified Presence Administration:
Release 7.0: Application > Cisco Unified Personal Communicator > Conferencing Server
Release 6.x: Application > Cisco Unified Personal Communicator > MeetingPlace Server
Step 2 Click Add New in the Find and List window to add a new server.
Step 3 Enter information into the fields.
Step 4 Click Save.
Related Topics
•Creating Conferencing Profiles in Cisco Unified Presence Administration
Creating Conferencing Profiles in Cisco Unified Presence Administration
You must create conferencing profiles in Cisco Unified Presence Administration and assign each to a primary server.
Note By contrast, a profile in Cisco Unified MeetingPlace or in Cisco Unified MeetingPlace Express defines the privileges and preferences configured for a specific user in this application.
Before You Begin
•You must create the conferencing profile before you can add Cisco Unified Personal Communicator licensed users to the application profile.
•You must first specify conferencing server names and addresses before you can select them in this procedure.
Restrictions
Conferencing server failover is not supported in Cisco Unified Personal Communicator Release 7.0(1).
Procedure
Step 1 Select the following menu in Cisco Unified Presence Administration:
Release 7.0: Application > Cisco Unified Personal Communicator > Conferencing Profile
Release 6.x: Application > Cisco Unified Personal Communicator > MeetingPlace Profile
Step 2 Click Add New in the Find and List window to add a new profile.
Step 3 Enter information into the fields.
Step 4 Click Save.
Related Topics
•Changing Application Profiles for a Single User, page 2-32
•Specifying Conferencing Server Names and Addresses in Cisco Unified Presence Administration
Configuring Videoconferencing Resources
Through Cisco Unified Communications Manager Administration, you can enable merged conference calls (three or more parties) with audio and video support for Cisco Unified Personal Communicator soft-phone users. Any participant in the conference call can merge other participants into the conference.
Before You Begin
•Install a supported release of the videoconferencing server. For details about the server installation:
http://www.cisco.com/en/US/products/hw/video/ps1870/tsd_products_support_series_home.html
For details about supported Cisco Unified Videoconferencing releases, see the Cisco Unified Personal Communicator release notes:
http://www.cisco.com/en/US/products/ps6844/prod_release_notes_list.html
•Obtain the MAC address of the videoconference bridge.
Procedure
Step 1 Select Media Resources > Conference Bridge.
Step 2 Add the videoconference bridge.
Step 3 Select Media Resources > Media Resource Group List.
Step 4 Create a media resource group list.
Step 5 Add the videoconference bridge to the media resource group list.
Step 6 Select Media Resources > Media Resource Group.
Step 7 Create a media resource group.
Step 8 Add a media resource to the media resource group.
Step 9 (Optional) To enable any participant to add more participants the conference, perform the following steps:
a. Select System > Service Parameters.
b. Select the Cisco Unified Communications Manager server and service.
c. Set Advanced Ad Hoc Conference Enabled to True in the Clusterwide Parameter (Feature - Conference) section.
Step 10 Associate the phone with the new media resource group list:
a. Select Device > Phone in Cisco Unified Communications Manager Administration.
b. Under Search Options, search for the directory number of the phone, and when it is found, click the device name.
c. In the Phone Configuration window in the Device Information section, find the Media Resource Group List, and select the media resource group list that you just configured.
d. Select Enabled for Video Capabilities in the Product Specific Configuration Layout section.
e. Click Save.
f. Click Reset.
For detailed configuration instructions, use the Cisco Unified Communications Manager Administration online help or the Cisco Unified Communications Manager Administration Guide:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
Related Topics
•Adding Cisco Unified Personal Communicator as a Phone Type, page 2-5
•Configuring Users for Point-to-Point Video Calls and for Multipoint Videoconferencing, page 2-34