Cisco IP Phone 7800 Series Release Notes for Firmware Release 12.0(1)

These release notes support the Cisco IP Phones 7811, 7821, 7841, and 7861 running SIP Firmware Release 12.0(1).

The following table lists the Cisco Unified Communications Manager release and protocol compatibility for the Cisco IP Phones.

Table 1. Cisco IP Phones, Cisco Unified Communications Manager, and Firmware Release Compatibility

Cisco IP Phone

Protocol

Cisco Unified Communications Manager

Cisco IP Phones 7811, 7821, 7841, and 7861

SIP

Cisco Unified Communications Manager version 8.5(1) and later

Cisco Unified Communications Manager DST Olsen version D or later

SRST 8.0 (IOS load 15.1(1)T) and above

Cisco IP Phones 7811, 7821, 7841, and 7861

SIP

CME 10.0 (IOS load 15.3(3)M)

Cisco IP Phones 7811, 7821, 7841, and 7861

Cisco Expressway X8.7 or Cisco TelePresence Video Communication Server X8.7 (for Mobile and Remote Access)

Related Documentation

Use the following sections to obtain related information.

New and Changed Features

The following sections describe the features that are new or have changed in this release.

Features Available with the Firmware Release

The following sections describe the features available with the Firmware Release.

IPv6 Feature Support

The following features are now supported in IPv6:

  • Survivable Remote Site Telephony version 6 (SRSTv6)

  • Voicemail and Visual Voicemail

  • Personal Directory and Corporate Directory

  • IPv6 EM

  • Idle URL

  • Service URL

  • Authenticate URL

  • XSI

Where to Find More Information
  • Cisco IP Phone 7800 Series Administration Guide for Cisco Unified Communications Manager

  • IPv6 Deployment Guide for Cisco Collaboration Systems Release 12.0

Mobile and Remote Access Through Expressway and Domain Name Handling

Mobile and Remote Access Through Expressway users can now login using a domain that is different than the Expressway domain. This enhancement allows adminstrators to deploy multiple UC clusters in different domains.

Where to Find More Information
  • Cisco IP Phone 7800 Series Administration Guide for Cisco Unified Communications Manager

Installation

Installation Requirements

Before you install the firmware release, you must ensure that your Cisco Unified Communications Manager is running the latest device pack. After you install a device pack on the Cisco Unified Communications Manager servers in the cluster, you need to reboot all the servers.


Note

If your Cisco Unified Communications Manager does not have the required device pack to support this firmware release, the firmware may not work correctly.


For information on the Cisco Unified Communications Manager Device Packs, see http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/compat/devpack_comp_mtx.html.

Upgrade from a pre-11.5(1) Firmware Release

Your Cisco IP Phone 7800 Series phone may have trouble booting up if you are upgrading from a pre-11.5(1) release to 12.0(1) firmware. If your phone uses an earlier firmware release, then follow one of these procedures:

  • Upgrade from a pre-11.5(1) release to 11.5(1) firmware first and then upgrade from 11.5(1) to 12.0(1) firmware or later.

  • Upgrade from a pre-11.5(1) release to 12.0.1ES5 release or later.

Install the Firmware Release on Cisco Unified Communications Manager

Before using the Cisco Unified IP Phone Firmware Release 12.0(1) with Cisco Unified Communications Manager, you must install the latest firmware on all Cisco Unified Communications Manager servers in the cluster.

Procedure


Step 1

Go to the following URL:

Step 2

Choose Cisco IP Phones 7800 Series.

Step 3

Choose your phone model.

Step 4

Choose Session Initiation Protocol (SIP) Software.

Step 5

In the Latest Releases folder, choose 12.0(1).

Step 6

Select the following firmware file, click the Download or Add to cart button, and follow the prompts:

  • cmterm-78xx.12-0-1-11.k3.cop.sgn
Note 

If you added the firmware file to the cart, click the Download Cart link when you are ready to download the file.

Step 7

Click the + next to the firmware file name in the Download Cart section to access additional information about this file. The hyperlink for the readme file is in the Additional Information section, which contains installation instructions for the corresponding firmware.

Step 8

Follow the instructions in the readme file to install the firmware.


Install the Firmware Zip Files

If a Cisco Unified Communications Manager is not available to load the installer program, the following zip files are available to load the firmware.

  • cmterm-78xx.12-0-1-11.zip

Procedure


Step 1

Go to the following URL:

Step 2

Choose Cisco IP Phones 7800 Series.

Step 3

Choose your phone model.

Step 4

Choose Session Initiation Protocol (SIP) Software.

Step 5

In the Latest Releases folder, choose 12.0(1).

Step 6

Download the relevant zip files.

Step 7

Unzip the files.

Step 8

Manually copy the unzipped files to the directory on the TFTP server. See Cisco Unified Communications Operating System Administration Guide for information about how to manually copy the firmware files to the server.


Limitations and Restrictions

Manufacturing Installed Certificate Signature and SHA-256 Support

The manufacturing installed certificate(MIC) signature has been updated from SHA-128 with RSA to SHA-256 with RSA. You must update and install the new SHA-2 certificates on the Cisco Unified Communications Manager for secure mode to function. You can download the new certificate from http://www.cisco.com/security/pki/certs/cmca2.cer.

All applications that authenticate the phone MIC should update the MIC, including the following:
  • Cisco Unified Communications Manager

  • Cisco Unified Survivable Remote Site Telephony

  • Cisco Secure Access Control System

  • Cisco Identity Services Engine

For additional information about SHA-2 use and support, see Security Guide for Cisco Unified Communications Manager.

Phone Behavior During Times of Network Congestion

Anything that degrades network performance can affect phone voice and video quality, and in some cases, can cause a call to drop. Sources of network degradation can include, but are not limited to, the following activities:

  • Administrative tasks, such as an internal port scan or security scan

  • Attacks that occur on your network, such as a Denial of Service attack

Health-Care Environment Use

This product is not a medical device and uses an unlicensed frequency band that is susceptible to interference from other devices or equipment.

On-Hook Transfer Limitation in SIP Phones

When the Cisco Unified Communications Manager Transfer On-Hook Enabled field is enabled, users might report a problem with direct call transfer in SIP phones. If the user transfers the call and immediately goes on hook before they hear the ring signal, the call may drop instead of being transferred.

The user needs to hear the ring signal so that they can be sure that the call is being routed.

Ringtone Limitation During Firmware Downgrade from Release 11.0

When the phone downgrades from Firmware Release 11.0 to Firmware Release 10.3, the phone may not ring when there is an incoming call. The ringtone for the line has been deleted and must be manually set in the Settings > Ringtone menu.

Connections with the PC and SW Ports

If you only have one LAN cable at your desk, you can plug your phone into the LAN with the SW port and then connect your computer into the PC port.

You can also daisy chain two phones together. Connect the PC port of the first phone to the SW port of the second phone.


Caution

Do not connect the SW and PC ports into the LAN.


Language Limitation

There is no localized Keyboard Alphanumeric Text Entry (KATE) support for the following Asian locales:

  • Chinese (China)

  • Chinese (Hong Kong)

  • Chinese (Taiwan)

  • Japanese (Japan)

  • Korean (Korea Republic)

The default English (United States) KATE is presented to the user instead.

For example, the phone screen will show text in Korean, but the 2 key on the keypad will display a b c 2 A B C.

View Caveats

You can search for caveats using the Cisco Bug Search.

Known caveats (bugs) are graded according to severity level, and can be either open or resolved.

Before you begin

To view caveats, you need the following items:

  • Internet connection

  • Web browser

  • Cisco.com user ID and password

Procedure


Step 1

Perform one of the following actions:

Step 2

When prompted, log in with your Cisco.com user ID and password.

Step 3

(Optional) Enter the bug ID number in the Search for field, then press Enter.


Cisco Unified Communication Manager Public Keys

To improve software integrity protection, new public keys are used to sign cop files for Cisco Unified Communications Manager Release 10.0.1 and later. These cop files have "k3" in their name. To install a k3 cop file on a pre-10.0.1 Cisco Unified Communications Manager, consult the README for the ciscocm.version3-keys.cop.sgn to determine if this additional cop file must first be installed on your specific Cisco Unified Communications Manager version. If these keys are not present and are required, you will see the error "The selected file is not valid" when you try to install the software package.

Unified Communications Manager Endpoints Locale Installer

By default, Cisco IP Phones are set up for the English (United States) locale. To use the Cisco IP Phones in other locales, you must install the locale-specific version of the Unified Communications Manager Endpoints Locale Installer on every Cisco Unified Communications Manager server in the cluster. The Locale Installer installs the latest translated text for the phone user interface and country-specific phone tones on your system so that they are available for the Cisco IP Phones.

To access the Locale Installer required for a release, access https://software.cisco.com/download/navigator.html?mdfid=286037605&flowid=46245, navigate to your phone model, and select the Unified Communications Manager Endpoints Locale Installer link.

For more information, see the documentation for your particular Cisco Unified Communications Manager release.


Note

The latest Locale Installer may not be immediately available; continue to check the website for updates.


Cisco IP Phone Documentation Updates on Cisco Unified Communications Manager

The Cisco Unified Communications Manager Self Care Portal (Release 10.0 and later) and User Options web pages (Release 9.1 and earlier) provide links to the IP Phone user guides in PDF format. These user guides are stored on the Cisco Unified Communications Manager and are up to date when the Cisco Unified Communications Manager release is first made available to customers.

After a Cisco Unified Communications Manager release, subsequent updates to the user guides appear only on the Cisco website. The phone firmware release notes contain the applicable documentation URLs. In the web pages, updated documents display "Updated" beside the document link.


Note

The Cisco Unified Communications Manager Device Packages and the Unified Communications Manager Endpoints Locale Installer do not update the English user guides on the Cisco Unified Communications Manager.


You and your users should check the Cisco website for updated user guides and download the PDF files. You can also make the files available to your users on your company website.


Tip

You may want to bookmark the web pages for the phone models that are deployed in your company and send these URLs to your users.


Documentation, Service Requests, and Additional Information

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.