تكوين البث المتعدد لبروتوكول VRF بين شبكات VRF دون تسريب المسار بين شبكات VRF

المقدمة

يصف هذا المستند كيفية إعادة توجيه تدفق بث متعدد البث يأتي من مصدر في مصدر التوجيه وإعادة التوجيه الظاهري (VRF) ويتجه نحو المستخدمين في مستقبل VRF دون إجراء تسريب المسار بين VRF للبث الأحادي.

المتطلبات الأساسية

المتطلبات

توصي Cisco بأن تكون لديك معرفة بوظائف PIM و ASM.

المكونات المستخدمة

تستند المعلومات الواردة في هذا المستند إلى ASR1000.

تم إنشاء المعلومات الواردة في هذا المستند من الأجهزة الموجودة في بيئة معملية خاصة. بدأت جميع الأجهزة المُستخدمة في هذا المستند بتكوين ممسوح (افتراضي). إذا كانت شبكتك قيد التشغيل، فتأكد من فهمك للتأثير المحتمل لأي أمر.

الرسم التخطيطي للشبكة

التكوينات

قم بإنشاء دفق UDP للبث المتعدد على المصدر.

Source#

ip sla 1

udp-echo 239.1.1.1 2000 source-ip 10.1.1.1

ip sla schedule 1 life forever start-time now

يتم تكوين جهاز الاستقبال باستخدام بروتوكول IGMP ويرسل تقارير عضوية IGMP.

يقوم الموجه ASR1000 بإعادة توجيه حركة مرور البث المتعدد بين شبكات VRF. الاسترجاع 1 في VRF 'source' هو RP لكل من VRFs.

ASR1000#

ip vrf source

rd 1:1

!

ip vrf receiver

rd 2:2

!

ip multicast-routing vrf source distributed

ip multicast-routing vrf receiver distributed


ip pim vrf source rp-address 1.1.1.1

ip pim vrf receiver rp-address 1.1.1.1


interface Loopback1

ip vrf forwarding source

ip address 1.1.1.1 255.255.255.255

ip pim sparse-mode


interface GigabitEthernet0/0/0

ip vrf forwarding source

ip address 10.1.1.2 255.255.255.0

ip pim sparse-mode


interface GigabitEthernet0/0/1

ip vrf forwarding receiver

ip address 20.1.1.2 255.255.255.0

ip pim sparse-mode

(s، g) لم يتم تكوين الإدخال في VRF "إستقبال" في الوقت الحالي.

ASR1002-1#show ip mroute vrf source

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,

L - Local, P - Pruned, R - RP-bit set, F - Register flag,

T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,

X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,

U - URD, I - Received Source Specific Host Report,

Z - Multicast Tunnel, z - MDT-data group sender,

Y - Joined MDT-data group, y - Sending to MDT-data group,

G - Received BGP C-Mroute, g - Sent BGP C-Mroute,

N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,

Q - Received BGP S-A Route, q - Sent BGP S-A Route,

V - RD & Vector, v - Vector, p - PIM Joins on route,

x - VxLAN group, c - PFP-SA cache created entry,

* - determined by Assert

Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join

Timers: Uptime/Expires

Interface state: Interface, Next-Hop or VCD, State/Mode


(*, 239.1.1.1), 00:05:01/stopped, RP 1.1.1.1, flags: SPF

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list: Null

(10.1.1.1, 239.1.1.1), 00:05:01/00:02:26, flags: PFT

Incoming interface: GigabitEthernet0/0/0, RPF nbr 0.0.0.0

Outgoing interface list: Null


(*, 224.0.1.40), 00:07:03/00:02:59, RP 1.1.1.1, flags: SJCL

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list:

Loopback1, Forward/Sparse, 00:07:01/00:02:59

ASR1002-X-1#sh ip mroute vrf receiver
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode


(*, 239.1.1.1), 00:03:23/00:02:44, RP 1.1.1.1, flags: SJC
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet0/0/1, Forward/Sparse, 00:03:23/00:02:44

لإصلاح هذا، يلزمك تحديد VRF لتمرير التحقق من إعادة توجيه المسار العكسي (RPF).

ip access-list standard 1

permit 239.1.1.1 log

exit

ip multicast vrf receiver rpf select vrf source group-list 1

التحقق من الصحة

استخدم هذا القسم لتأكيد عمل التكوين بشكل صحيح.

بعد تنفيذ الخطوات المذكورة سابقا، يمكن رؤية موجز ويب البث المتعدد على المستقبل.

Receiver#show flow monitor test cache format table

Cache type: Normal (Platform cache)

Cache size: 200000

Current entries: 1

High Watermark: 3


Flows added: 50

Flows aged: 49

- Inactive timeout ( 15 secs) 49


IPV4 SRC ADDR IPV4 DST ADDR TRNS SRC PORT TRNS DST PORT INTF INPUT FLOW SAMPLER ID IP TOS IP PROT ip src as ip dst as ipv4 next hop addr ipv4 src mask ipv4 dst mask tcp flags intf output bytes pkts time first time last

=============== =============== ============= ============= ==================== =============== ====== ======= ========= ========= ================== ============= ============= ========= ==================== ========== ========== ============ ============

10.1.1.1 239.1.1.1 57314 1967 Gi0/0/3 0 0x00 17 0 0 0.0.0.0 /0 /0 0x00 Null 80 1 11:09:08.082 11:09:08.082

التقاط الحزمة على المستقبل.

(s، g) يتم تكوين الإدخال في مستقبل VRF.

ASR1002-1#show ip mroute vrf receiver 239.1.1.1 
IP Multicast Routing Table 
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, 
P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, 
M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, 
A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, 
y - Sending to MDT-data group, G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, V - RD & Vector, v - Vector, 
p - PIM Joins on route, x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert Outgoing interface flags: H - Hardware switched, 
A - Assert winner, p - PIM Join 
Timers: Uptime/Expires 
Interface state: 
Interface, Next-Hop or VCD, State/Mode 

(*, 239.1.1.1), 00:21:36/stopped, RP 1.1.1.1, flags: SJC
Incoming interface: Loopback1, RPF nbr 1.1.1.1, using vrf source
Outgoing interface list:
GigabitEthernet0/0/1, Forward/Sparse, 00:21:36/00:02:43

(10.1.1.1, 239.1.1.1), 00:03:55/stopped, flags: T
Incoming interface: GigabitEthernet0/0/0, RPF nbr 0.0.0.0, using vrf source
Outgoing interface list:
GigabitEthernet0/0/1, Forward/Sparse, 00:03:55/00:02:43


ASR1002-1#show ip mroute vrf source 239.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.1.1.1), 00:22:36/stopped, RP 1.1.1.1, flags: SJCFE
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list: Null

Extranet receivers in vrf receiver:
(*, 239.1.1.1), 00:21:54/stopped, RP 1.1.1.1, OIF count: 1, flags: SJC

(10.1.1.1, 239.1.1.1), 00:04:14/00:02:55, flags: FTE
Incoming interface: GigabitEthernet0/0/0, RPF nbr 0.0.0.0
Outgoing interface list: Null

Extranet receivers in vrf receiver:
(10.1.1.1, 239.1.1.1), 00:04:14/stopped, OIF count: 1, flags: T


ASR1002-1#show ip mfib vrf receiver 239.1.1.1
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup

Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
VRF receiver
(*,239.1.1.1) Flags: C HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 0/0/0/0, Other: 1/1/0
GigabitEthernet0/0/1 Flags: NS
(10.1.1.1,239.1.1.1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 15/0/94/0, Other: 0/0/0
GigabitEthernet0/0/1 Flags: NS

أيضا، هناك ما من unicast مدخل في ال VRF مستقبل RIB ل RP والمصدر IP.

ASR1002-1#show ip route vrf receiver 1.1.1.1 
Routing Table: receiver % Network not in table 

ASR1002-1#show ip route vrf receiver 10.1.1.1 
Routing Table: receiver % Network not in table

وبالتالي، تظهر إعادة توجيه المسار العكسي (RPF) كفشل متوقع، ومع ذلك، ستتم إعادة توجيه حركة مرور البث المتعدد.

ASR1002-1#show ip rpf vrf receiver 1.1.1.1 
failed, no route exists 
ASR1002-1#show ip rpf vrf receiver 10.1.1.1 
failed, no route exists 

وهناك طريقة أخرى لتحقيق هذا، وهي كما يلي:

ip mroute vrf receiver 10.1.1.0 255.255.255.0 fallback-lookup vrf source 

ip mroute vrf receiver 1.1.1.1 255.255.255.255 fallback-lookup vrf source 

بهذا، سيكون التحقق من إعادة توجيه المسار العكسي (RPF) ناجحا.

ASR1002-1#show ip rpf vrf receiver 1.1.1.1
RPF information for ? (1.1.1.1)
RPF interface: Loopback1
RPF neighbor: ? (1.1.1.1) - directly connected
RPF route/mask: 1.1.1.1/32
RPF type: multicast (connected)
Doing distance-preferred lookups across tables
Using Extranet RPF Rule: Static Fallback Lookup, RPF VRF: source
RPF topology: ipv4 multicast base

ASR1002-1#show ip rpf vrf receiver 10.1.1.1
RPF information for ? (10.1.1.1)
RPF interface: GigabitEthernet0/0/0
RPF neighbor: ? (10.1.1.1) - directly connected
RPF route/mask: 10.1.1.0/24
RPF type: multicast (connected)
Doing distance-preferred lookups across tables
Using Extranet RPF Rule: Static Fallback Lookup, RPF VRF: source
RPF topology: ipv4 multicast base

ومع ذلك، يمكنك إستخدام إما أمر تحديد إعادة توجيه المسار العكسي (RPF) أو أمر البحث الاحتياطي، وكلاهما يفي بهدفنا في نهاية المطاف.

استكشاف الأخطاء وإصلاحها

لا تتوفر حاليًا معلومات محددة لاستكشاف الأخطاء وإصلاحها لهذا التكوين.