Small Business
WAP321 Wireless-N Selectable-Band Access Point with Power Over Ethernet
(cisco)
Log Out
About
Help
Loading Setup Wizard...
Access Point Setup Wizard
Welcome
Configuration
IP Address
Time Settings
Security
Device Password
Network Name
Wireless Security
Summary
Finish
Thank you for choosing Cisco Small Business. This setup wizard will help you install your Cisco Small Business Access Point.
To setup this access point manually you can cancel this wizard at any time (Not recommended).
Note:
This Setup Wizard provides simplified options to help you quickly get your access point up and running. If there is any option or capability that you do not see while running the setup wizard, click the learning link provided on many of the setup wizard pages. To set further options as you require or as seen in the learning link, cancel the setup wizard and go to the web-based configuration utility.
Select either Dynamic or Static IP address for your device.
Dynamic IP Address (DHCP) (Recommended)
Static IP Address
Static IP Address:
.
.
.
Subnet Mask:
.
.
.
Default Gateway:
.
.
.
DNS:
.
.
.
Secondary DNS (optional):
.
.
.
Learn more about the different connection types
Enter the time zone, date and time.
Time Zone:
Set System Time:
Network Time Protocol (NTP)
Manually
System Date:
January
February
March
April
May
June
July
August
September
October
November
December
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
System Time:
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
:
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
NTP Server:
The administrative password protects your access point from unauthorized access. For security reasons, you should change the access point password from its default settings. Please write this password down for future reference.
Enter a new device password:
New password needs at least 8 characters composed of lower and upper case letters as well as numbers/symbols by default.
New Password:
Confirm Password:
Password Strength Meter:
Below Minimum
Password Complexity:
Enable
Learn more about passwords
The name of your wireless network, known as an SSID, identifies your network so that wireless devices can find it.
Enter a name for your wireless network:
Network Name (SSID):
For example: MyNetwork
Learn more about network names
Select your network security strength.
Best Security (WPA2 Personal - AES)
Recommended for new wireless computers and devices that support this option.
Older wireless devices might not support this option.
Better Security (WPA Personal - TKIP/AES)
Recommended for older wireless computers and devices that might not support WPA2.
No Security (Not recommended)
Enter a security key with 8-63 characters.
Below Minimum
Show Key as Clear Text
Learn more about your network security options
Please review the following settings and ensure the data is correct.
Network Name (SSID):
Network Security Type:
Security Key:
Cisco Setup Wizard will now enable your security.
Enabling Security...
This might take a few moments.
Congratulations, your access point has been set up successfully. We strongly recommend that you save these settings by writing them down or by copying and pasting them into a text document. You will need these settings later when you add other wireless computers or devices to your network.
network name (SSID):
network security type:
security key:
N/A
Note: To configure WPS, Click "Run WPS" on the Getting Started page, under Initial Setup.
© 2012 Cisco Systems. All rights reserved.