Cisco Unity System Administration Guide (With IBM Lotus Domino), Release 4.0(5)
Appendix: Exiting and Starting the Cisco Unity Software and Server

Table Of Contents

Exiting and Starting the Cisco Unity Software and Server

Exiting the Cisco Unity Software

Shutting Down or Restarting the Cisco Unity Server

Starting the Cisco Unity Software


Exiting and Starting the Cisco Unity Software and Server


The following sections provide instructions on exiting the Cisco Unity software, shutting down and restarting the Cisco Unity server, and starting the Cisco Unity software.


Note For details on the accounts that you use to log on to the Cisco Unity server and the Cisco Unity Status Monitor, see the "About the Accounts That Can Be Used to Administer Cisco Unity" section on page 2-5.


Exiting the Cisco Unity Software

This section contains two procedures for exiting the Cisco Unity software: from the Cisco Unity server and from another computer.


Caution Do not use Kill av*.* to exit the Cisco Unity software. Kill av*.* does not stop all Cisco Unity services.

Do not stop AvCsMgr by using the Services window or the Component Services window as a method to exit the Cisco Unity software. Stopping the AvCsMgr does not stop all Cisco Unity services and may cause unexpected results.

To Exit the Cisco Unity Software from the Cisco Unity Server


Step 1 If the system uses the automated attendant, route all calls to the operator.

Step 2 On the Cisco Unity server, log on to Windows by using either the Cisco Unity administration account or an appropriate Windows domain account.

Step 3 Right-click the Cisco Unity icon in the status area of the taskbar.

(If the Cisco Unity icon is not in the taskbar, browse to the CommServer directory, and double-click AvCsTrayStatus.exe.)

Step 4 Click Stop Cisco Unity. Cisco Unity stops running when all calls are finished, and an "X" appears in the Cisco Unity icon.

Step 5 Press Ctrl-Alt-Delete, then lock or log off of Windows to prevent access by unauthorized users.


To Exit the Cisco Unity Software from Another Computer


Step 1 If the system uses the automated attendant, route all calls to the operator.

Step 2 If the Cisco Unity Status Monitor does not use Integrated Windows authentication, skip to Step 3.

When the Cisco Unity Status Monitor uses Integrated Windows authentication, do the following substeps to access the Status Monitor:

a. Log on to Windows by using either the Cisco Unity administration account or an appropriate Windows domain account.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

c. If Internet Explorer prompts you for a user name and password, enter the user name, password, and domain for the administration account or the Windows domain account.

d. Skip to Step 6.

Step 3 When the Cisco Unity Status Monitor uses Anonymous authentication, do the following substeps to access the Status Monitor:

a. Log on to Windows by using any domain account that has the right to log on locally.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

Step 4 On the Cisco Unity Log On Page, do one of the following:

Enter the full name and Internet password of a Domino account that is associated with an appropriate Cisco Unity subscriber account, and click Log On, then skip to Step 6.

Click Log On Using Windows Authentication.

Step 5 On the Cisco Unity Log On page, enter the user name, password, and domain for the Cisco Unity administration account or the Windows domain account, and click Log On.

Step 6 In the Cisco Unity Status Monitor, under Shutting Down Cisco Unity, choose a method:

Cisco Unity stops running after all calls are finished.

Cisco Unity interrupts calls in progress with a voice message, disconnects all calls, then stops running.

Step 7 Click Shut Down.


Shutting Down or Restarting the Cisco Unity Server

If the Cisco Unity system has an expansion chassis or is set up for failover, note the following considerations before shutting down or restarting the Cisco Unity server:

Expansion chassis connected
to the Cisco Unity server

When both the expansion chassis and the Cisco Unity server are turned off, turn on the expansion chassis before you turn on the server. Otherwise, the server may not detect the voice cards in the expansion chassis.

Cisco Unity failover

When both servers are running and the active server is shut down, the inactive server becomes active.

When neither server is running, the first server started becomes the active server.

When the secondary server is active and configured for automatic failback, and the primary server is also running, the secondary server attempts failback on the failback schedule.


To Shut Down or Restart the Cisco Unity Server


Step 1 Exit the Cisco Unity software, if it is running, by using one of the procedures in the "Exiting the Cisco Unity Software" section.

Step 2 On the Windows Start menu, click Shut Down.

Step 3 Click Shut Down or Restart. During a restart, the Cisco Unity software starts automatically.

When Cisco Unity starts successfully, three tones play and a check mark appears in the Cisco Unity icon in the status area of the taskbar.

When Cisco Unity does not start successfully, two tones play and an "X" appears in the Cisco Unity icon in the status area of the taskbar.


Starting the Cisco Unity Software

This section contains two procedures for starting the Cisco Unity software: from the Cisco Unity server and from another computer.

Cisco Unity is a Windows service that is configured to start automatically when you turn on or restart the server. Do one of the procedures in this section only if you exited the Cisco Unity software and did not restart the server.

Domino must be running on the server that Cisco Unity connects with before you start the Cisco Unity software.

If Domino stops for any reason while Cisco Unity is running, Cisco Unity will continue to take messages.

To Start the Cisco Unity Software from the Cisco Unity Server


Step 1 On the Cisco Unity server, log on to Windows by using either the Cisco Unity administration account or an appropriate Windows domain account.

Step 2 Right-click the Cisco Unity icon in the status area of the taskbar.

(If the Cisco Unity icon is not in the taskbar, browse to the CommServer directory, and double-click AvCsTrayStatus.exe.)

Step 3 Click Start Cisco Unity.

When Cisco Unity starts successfully, three tones play and a check mark appears in the Cisco Unity icon.

When Cisco Unity does not start successfully, two tones play and an "X" appears in the Cisco Unity icon.

Step 4 Press Ctrl-Alt-Delete, then lock or log off of Windows to prevent access by unauthorized users.

Step 5 If the system uses the automated attendant and you routed calls to the operator before you exited the Cisco Unity software, reroute calls to Cisco Unity.


To Start the Cisco Unity Software from Another Computer


Step 1 If the Cisco Unity Status Monitor does not use Integrated Windows authentication, skip to Step 2.

When the Cisco Unity Status Monitor uses Integrated Windows authentication, do the following substeps to access the Status Monitor:

a. Log on to Windows by using either the Cisco Unity administration account or an appropriate Windows domain account.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

c. If Internet Explorer prompts you for a user name and password, enter the user name, password, and domain for the Cisco Unity administration account or the Windows domain account.

d. Skip to Step 5.

Step 2 When the Cisco Unity Status Monitor uses Anonymous authentication, do the following substeps to access the Status Monitor:

a. Log on to Windows by using any domain account that has the right to log on locally.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

Step 3 On the Cisco Unity Log On Page, do one of the following:

Enter the full name and Internet password of a Domino account that is associated with an appropriate Cisco Unity subscriber account, and click Log On, then skip to Step 5.

Click Log On Using Windows Authentication.

Step 4 On the Cisco Unity Log On page, enter the user name, password, and domain for the Cisco Unity administration account or the Windows domain account, and click Log On.

Step 5 In the Cisco Unity Status Monitor, click the System Status icon (the first icon), at the top of the page.

Step 6 Click Start.

Step 7 If the system uses the automated attendant and you routed calls to the operator before you exited the Cisco Unity software, reroute calls to Cisco Unity.