Cisco MDS 9000 Family Command Reference, Release 1.3 (from Release 1.3(1) through Release 1.3(6)) - Advanced Services Module Commands [Cisco MDS 9000 NX-OS and SAN-OS Software]

Table Of Contents

Advanced Services Module Commands

attach module — show fcdd

attach module — show npc

attach module — show vec

attach module — show ves

attach module — show version

attach module — show virt-lookup

attach module — show vsha

attach module — terminal

attachpriv module

asm mgmt-vsan

interface cpp

show asm

show flogi database

show flogi database

show interface

show fvport

Advanced Services Module Commands

The commands in this chapter are specific to the Advanced Services Module (ASM) used in the Cisco MDS 9216 Switch and the Cisco MDS 9500 Series. All commands are shown here in alphabetical order regardless of command mode.

See the "About the CLI Command Modes" section to determine the appropriate mode for each command. For more information on virtualization using the ASM, see the "Related Documentation" section.

•attach module — show fcdd

•attach module — show vec

•attach module — show ves

•attach module — show version

•attach module — show virt-lookup

•attach module — show virt-lookup

•attach module — terminal

•attachpriv module

•asm mgmt-vsan

•interface cpp

•show asm

•show flogi database

•show interface

•show fvport

attach module — show fcdd

To display the Fibre Channel Device Discovery (FCDD) information, use the show fcdd command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt.

attach module slot-number
show fcdd option
Syntax Description

attach module slot-number

Attaches to the ASM module.

show fcdd

Displays FCDD information.

option

eventlog — Displays information of various state machines
history — Displays FCDD history buffer
nvp — Displays FCDD for the virtual Nx port (NVP)
pid — Displays Path Ids
rescan — Displays FCDD disk rescan information
target — Displays Disk/VM VSAN FC targets

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VEC-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays target FCDD information for the ASM in slot 2.
module-2# show fcdd history
1) Event:E_DEBUG, length:67, at 617784 usecs after Thu Sep 18 17:55:04 2003
    [103] fcdd_demux(*event=0x7ffffb90,**ret_fsm_event_list=0x7ffff920)
2) Event:E_DEBUG, length:48, at 617759 usecs after Thu Sep 18 17:55:04 2003
    [103] fcdd_mts_dequeue_event(*ret_ev=0x7ffffb90)
3) Event:E_DEBUG, length:71, at 617751 usecs after Thu Sep 18 17:55:04 2003
    [103] fcdd_get_data_from_queue(*q_entry=0x2d8ea000, *ret_ev=0x7ffffb90)
4) Event:E_DEBUG, length:52, at 617739 usecs after Thu Sep 18 17:55:04 2003
    [103] fcdd_dequeue_event: Data Rcvd, Total ticks - 0
5) Event:E_DEBUG, length:20, at 511016 usecs after Thu Sep 18 17:54:57 2003
    [103]
...
module-2# show fcdd nvp vsan 3
FCDD NVP INFO:
VSAN		pWWN						FCID			LPI	DPP	SI		IF_INDEX			NUM_ZONE			
--------------------------------------------------------------------------------
   3		24:0a:00:05:30:00:94:a0						0x650009			1	1	0x0031		0x01091000			0
ZONE_CNT			ZONE_NAME
----------------------- 
module-2# show fcdd pid
CNT  PID    MINOR  VSAN  TGT_WWN                  LUN_ID                  STATE
-------------------------------------------------------------------------------
0    0x0011 272    3     21:00:00:20:37:46:78:97  00:00:00:00:00:00:00:00 INV_PD
1    0x0012 288    3     21:00:00:20:37:5b:cf:b9  00:00:00:00:00:00:00:00 INV_PD
2    0x0013 304    3     21:00:00:20:37:18:6f:90  00:00:00:00:00:00:00:00 INV_PD
3    0x0014 320    3     21:00:00:20:37:36:0b:4d  00:00:00:00:00:00:00:00 INV_PD
4    0x0015 336    3     21:00:00:20:37:39:90:6a  00:00:00:00:00:00:00:00 INV_PD
5    0x0016 352    3     21:00:00:20:37:18:d2:45  00:00:00:00:00:00:00:00 INV_PD
6    0x0017 368    3     21:00:00:20:37:38:a7:c1  00:00:00:00:00:00:00:00 INV_PD
7    0x0018 384    3     21:00:00:20:37:18:17:d2  00:00:00:00:00:00:00:00 INV_PD
8    0x0019 400    4     22:00:00:20:37:46:78:97  00:00:00:00:00:00:00:00 ACTIV
9    0x001a 416    4     22:00:00:20:37:5b:cf:b9  00:00:00:00:00:00:00:00 ACTIV
10   0x001b 432    4     22:00:00:20:37:18:6f:90  00:00:00:00:00:00:00:00 ACTIV
module-2# show fcdd target vsan 3
=======================================
All existing disks in VSAN    3:
=======================================
TGT_CNT pWWN                    FCID     SCSI_ID NUM_ZONE REDISC_TMR PERIOD(S) LAST_ACCESS
==========================================================================================
0       21:00:00:20:37:18:17:d2 0x7200c9 7       0               YES 600       Thu Sep 18 
18:00:32 2003
LUN_NUM LUN_ID                   MINOR  PID     TGT_WWN                 STATE    PERIOD(S) 
TIMER_STARTED
------------------------------------------------------------------------------------------
     0       00:00:00:00:00:00:00:00  384    0x0018  21:00:00:20:37:18:17:d2  ACTIVE   0
TGT_CNT pWWN                    FCID     SCSI_ID NUM_ZONE REDISC_TMR PERIOD(S) LAST_ACCESS
==========================================================================================
1       21:00:00:20:37:18:d2:45 0x7200c5 5       0               YES 600       Thu Sep 18 
18:00:32 2003
LUN_NUM LUN_ID                   MINOR  PID     TGT_WWN                 STATE    PERIOD(S) 
TIMER_STARTED
------------------------------------------------------------------------------------------
     0       00:00:00:00:00:00:00:00  352    0x0016  21:00:00:20:37:18:d2:45  ACTIVE   0
TGT_CNT pWWN                    FCID     SCSI_ID NUM_ZONE REDISC_TMR PERIOD(S) LAST_ACCESS
==========================================================================================
2       21:00:00:20:37:5b:cf:b9 0x7200b6 1       0               YES 600       Thu Sep 18 
18:00:32 2003
...
attach module — show npc

To display the virtual N port creator (NPC) information, use the show npc command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt.

attach module slot-number
show npc option
Syntax Description

attach module slot-number

Attaches to the ASM module.

show npc

Displays NPC information.

option

history — Displays NPC history buffer
nvp — Displays NPC information for the virtual N port

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VEC-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays target FCDD information for the ASM in slot 2.
module-2# show npc history
module-2# show npc history
1) Event:E_DEBUG, length:66, at 123862 usecs after Thu Sep 18 18:24:50 2003
    [103] npc_demux(*event=0x7ffffb60,**ret_fsm_event_list=0x7ffff8f0)
2) Event:E_DEBUG, length:71, at 123849 usecs after Thu Sep 18 18:24:50 2003
    [105] 0x000000D0: 00 00 00 00 ...
3) Event:E_DEBUG, length:82, at 123818 usecs after Thu Sep 18 18:24:50 2003
    [105] 0x000000C0: 00 00 00 0C 00 00 00 00 00 00 00 00 00 00 00 00 ...
4) Event:E_DEBUG, length:82, at 123766 usecs after Thu Sep 18 18:24:50 2003
    [105] 0x000000B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
5) Event:E_DEBUG, length:82, at 123714 usecs after Thu Sep 18 18:24:50 2003
    [105] 0x000000A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
module-2# show npc nvp
COUNT VSAN pWWN                    FCID     LPI DPP SI     IF_INDEX   TCAM_TYPE 
STATE       U_CNT USERS
-------------------------------------------------------------------------------
-----------------------
0        2 10:00:00:00:5e:00:01:01 0x6f0000  17   1 0x0030 0x01090000 0x0205
ESTABLISHED   1   [ 31 ]
1        2 10:00:00:05:30:00:59:20 0x6f0002  17   1 0x0030 0x01090000 0x0205
ESTABLISHED   1   [ 31 ]
2        2 23:00:00:05:30:00:59:20 0x6f000b  19   1 0x0032 0x01092000 0x0206
ESTABLISHED   1   [ 918 ]
3        2 23:02:00:05:30:00:59:20 0x6f0003  18   1 0x0031 0x01091000 0x0206
ESTABLISHED   1   [ 918 ]
4        2 23:03:00:05:30:00:59:20 0x6f0004   1   2 0x0020 0x01080000 0x0206
ESTABLISHED   1   [ 918 ]
5        2 23:04:00:05:30:00:59:20 0x6f0005   5   3 0x0024 0x01084000 0x0206
ESTABLISHED   1   [ 918 ]
6        2 23:05:00:05:30:00:59:20 0x6f0006  21   4 0x0034 0x01094000 0x0206
ESTABLISHED   1   [ 918 ]
7        2 23:06:00:05:30:00:59:20 0x6f0007  25   5 0x0038 0x01098000 0x0206
ESTABLISHED   1   [ 918 ]
8        2 23:07:00:05:30:00:59:20 0x6f0008   9   6 0x0028 0x01088000 0x0206
ESTABLISHED   1   [ 918 ]
...
module-2# show npc nvp fsm 23:08:00:05:30:00:59:20 vsan 2
>>>>FSM: <NVP_23:08:00:05:30:00:59:20> has 7 logged transitions<<<<<
1) FSM:<NVP_23:08:00:05:30:00:59:20> Transition at 839998 usecs after Thu Sep 18
 17:57:23 2003
    Previous state: [NPC_NVP_NULL]
    Triggered event: [NPC_NVP_EV_NP_CREATION_REQ]
    Next state: [NPC_NVP_GET_IFINDEX]
2) FSM:<NVP_23:08:00:05:30:00:59:20> Transition at 840179 usecs after Thu Sep 18
 17:57:23 2003
    Previous state: [NPC_NVP_GET_IFINDEX]
    Triggered event: [NPC_NVP_EV_IF_INDEX_OK]
    Next state: [NPC_NVP_FVLOGI_SENT]
...
module-2# show npc nvp vsan 2
COUNT VSAN pWWN                    FCID     LPI DPP SI     IF_INDEX   TCAM_TYPE
STATE       U_CNT USERS
--------------------------------------------------------------------------------
-----------------------
0        2 10:00:00:00:5e:00:01:01 0x6f0000  17   1 0x0030 0x01090000 0x0205
ESTABLISHED   1   [ 31 ]
1        2 10:00:00:05:30:00:59:20 0x6f0002  17   1 0x0030 0x01090000 0x0205
ESTABLISHED   1   [ 31 ]
2        2 23:00:00:05:30:00:59:20 0x6f000b  19   1 0x0032 0x01092000 0x0206
ESTABLISHED   1   [ 918 ]
3        2 23:02:00:05:30:00:59:20 0x6f0003  18   1 0x0031 0x01091000 0x0206
ESTABLISHED   1   [ 918 ]
4        2 23:03:00:05:30:00:59:20 0x6f0004   1   2 0x0020 0x01080000 0x0206
ESTABLISHED   1   [ 918 ]
...
attach module — show vec

To display Virtual Enclosure Client (VEC) information, use the show vec command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt.

attach module slot-number
show vec option
Syntax Description

attach module slot-number

Attaches to the ASM module.

show vec

Displays configured VEC information.

option

asm — Displays VEC-related ASM information
dip — Displays Distributed Instantiation Protocol (DIP) information
dpp — Displays Data Path Processors (DPPs) State
dpp-hostmap — Displays DPP host maps
dpp-lunmap — Displays DPP LUN maps
error-statistics — Displays VEC error statistics
fp-port — Displays Front panel ports in the ASM
history — Displays VEC internal history buffer
host — Displays Logged in hosts
initiator-nports — Displays Disk/VM VSAN initiator N ports
login — Displays Disk/VM VSAN process logins
pid — Displays Path Ids
scsi-init — Displays SCSI initiator information
scsi-tgt — Displays SCSI target information
target — Displays Disk/VM VSAN FC targets
tp — Displays Trap Port (TP)
vep — Displays Virtual Enclosure Port (VEP)
ves — Displays Virtual Enclosure Server(s) (VES) connected to the VEC
vlun — Displays VLUNs
vlun-statistic — Displays Vlun error statistics
vmvsan-login — Displays DIOP logins
volume-owners — Displays Volume Owners
vsans — Displays VSANs seen by the VEC
xp-login — Displays logins (PLOGI/PRLI) to VEPs/TPs (xPs)

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VEC-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays target VEC information for the ASM in slot 2.
module-2# show vec target
vsan I dpp   here there pwwn                      target state
   3 A   0 72000a 720101 21:00:00:20:37:65:1c:cb  83995a8 PRLI_COMPLETE
   3 A   0 72000a 7201e8 21:00:00:20:37:65:1c:e3  839a188 PRLI_COMPLETE
   4 A   0 6b0009 7800ba 22:00:00:20:37:18:6f:90  83a7ce8 PRLI_COMPLETE
   3 A   0 72000a 7202ba 21:00:00:20:37:18:6f:90  83a5540 PRLI_COMPLETE
   4 A   0 6b0009 7800c9 22:00:00:20:37:18:17:d2  83aebd0 PRLI_COMPLETE
   3 A   0 72000a 7202c9 21:00:00:20:37:18:17:d2  83ad410 PRLI_COMPLETE
   2 A   2 6f0005 6f0005 23:04:00:05:30:00:59:20  837de70 PRLI_COMPLETE
   2 A   5 6f0008 6f0005 23:04:00:05:30:00:59:20  83866f8 PRLI_COMPLETE
   3 A   0 72000a 7201ef 21:00:00:20:37:89:ac:7f  839ad68 PRLI_COMPLETE
   4 A   0 6b0009 780100 50:06:04:82:bf:d0:cf:4b  839c998 PRLI_COMPLETE
   4 A   0 6b0009 7800bc 22:00:00:20:37:36:0b:4d  83a94a8 PRLI_COMPLETE
...
attach module — show ves

To display Virtual Enclosure Server (VES) information, use the show ves command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attached session.

attach module slot-number
show ves option
Syntax Description

attach module slot-number

Attaches to the ASM module.

show ves

Displays configured VES information for the ASM.

option

dg — Displays VES-related Disk Group information
diop—Displays Data-path Input Output Protocol (DIOP) information
dip — Displays Distributed Instantiation Protocol (DIP)
history — Displays VES internal history buffer
lunmap — Displays VES lunmap information
pid — Displays Path Id (PID) information
pid-evlog — Displays PID event log information
pid_vlun_sg — Displays PID/VLUN SG Table Information
scsi-tgt — Displays SCSI Target Module
sg — Displays Service Group
ve — Displays Virtual Enclosure (VE)
vec — Displays Virtual Enclosure Clients (VECs) connected to the VES
vep — Displays Virtual Enclosure Port (VEP)
vlun — Displays VLUN Table Information
vlun-counters — Displays VLUN counters
vlun-evlog — Displays VLUN event log
vsans — Displays VSANs seen by the VES

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VEC -specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays the virtual enclosure server's service group information for the ASM in slot 2.
module-2# show ves sg
            Virtual Enclosure Server Service Group Info
 ----------------------------------------------------------------------
 No      VR-ID              IP Address
 ----------------------------------------------------------------------
 0         0                    15.0.112.2
 1         1                    15.0.0.10
 2         2                    15.0.0.11
Number of Service Groups : 3...
The following examples display DIOP information for the ASM in slot 2.
module-2# show ves diop guid
VLUN-ID                 GUID
0000000000000001        c3ef7ce8-1dd1-11b2-a8de-75d21f738aa7
module-2# show ves diop stats
DIOP COUNTER         : Success          Failed
VLUN STRATEGY        : 0x00000000       0x00000000
VLUN DONE            : 0x00000000       0x00000000
DISK REMOTE STRATEGY : 0x00000000       0x00000000
DISK REMOTE DONE     : 0x00000000       0x00000000
DISK LOCAL STRATEGY  : 0x00000000       0x00000000
DISK LOCAL DONE      : 0x00000000       0x00000000
module-2# show ves diop vsvo
vsan    : 2
fcid    : 0x6F000B
dpp     : 0
module-2# show ves diop xp
Hash    VSAN    FCID    pWWN    RefCnt
2       2       6F000B  2300000530005920        1
3       2       6F0007  2306000530005920        1
7       2       6F0008  2307000530005920        1
10      2       6F0003  2302000530005920        1
11      2       6F0009  2308000530005920        1
14      2       6F0004  2303000530005920        1
15      2       6F000A  2309000530005920        1
18      2       6F0005  2304000530005920        1
22      2       6F0006  2305000530005920        1
attach module — show version

To display version information for the ASM module, use the show version command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attached session.

attach module slot-number
show version
Syntax Description

This command does not have any options.

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VSHA-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Use the show version command to verify the integrity of the image before loading the images. This command can be used for ASM images.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays the ASM version in slot 2.
module-2# show version
Software
  BIOS:      version 1.0.7
  system:    version 1.2(2) 
  BIOS compile time:       03/20/03
  system compile Time:     7/11/2003 14:00:00
Hardware
  RAM 963380 kB
  bootflash: 500736 blocks (block size 512b)
  00:05:30:00:AC:AA uptime is 0 days 21 hours 2 minute(s) 32 second(s)
attach module — show virt-lookup

To display virtualization lookup tables, use the show virt-lookup command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attached session.

attach module slot-number
show virt-lookup number [ d_id | vol-cfg ] [ entries | masks | keys | stats ]
Syntax Description

attach module slot-number

Attaches to the ASM module.

show virt-lookup

Displays virtualization lookup tables.

number

Specifies one of four table instances of the virtualization engine (ranges from 1 to 4).

d_id

Displays DID lookup information.

vol-cfg

Displays volume lookup information.

entries

Displays lookup entries.

keys

Displays lookup keys.

masks

Displays lookup masks.

stats

Displays lookup statistics.

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VSHA-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2#
The following example displays virtual engine 1 details for DID entries.
module-2# show virt-lookup 1 d-id entries
   INDEX  V  CL  EG_IDX  RSVD  SW_INDEX  MASK
00000000  1   2     0     000  00000000  0204
00000001  1   2     1     000  00000000  0204
00000400  1   2     0     000  FFFFFFFF  0205
00000401  1   2     0     000  FFFFFFFF  0207
00000402  1   2     0     000  FFFFFFFF  0206
00000403  1   2     1     000  FFFFFFFF  0206
00000404  1   2     0     000  FFFFFFFF  0206
00000405  1   2     0     000  FFFFFFFF  0206
00000406  1   2     1     000  FFFFFFFF  0206
00000407  1   2     0     000  FFFFFFFF  0206
00000408  1   2     0     000  FFFFFFFF  0206
00000409  1   2     1     000  FFFFFFFF  0206
0000040A  1   2     0     000  FFFFFFFF  0206
The following example displays volume lookup mask entries for virtualization engine 2.
module-2# show virt-lookup 2 vol-cfg masks
BLKINDEX  FL  V  CL  RESERVED  RESERVED   D_ID    S_ID   B1  B0  IN  PI  VSAN
              1   3  00000000  00000000  FFFFFF  000000  00  00   1   3   FFF
00001C00  3F
The following example displays statistics for volume lookup tables.
module-2# show virt-lookup 3 vol-cfg stats
TOTAL   USED  USED-DPP0  USED-DPP1
 8192      6          3          3
attach module — show vsha

To display volume server high availability (VSHA) information, use the show vsha command.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attached session.

attach module slot-number
show vsha option
Syntax Description

attach module slot-number

Attaches to the ASM module.

show vsha

Displays configured VSHA information.

option

dg-info — Displays VSHA SG-Disk_group information
sg-info — Displays VSHA SG Information
sg-log — Displays VSHA SG Event Log

Command Modes

EXEC (attach module mode).

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Access the ASM using the attach module command to obtain VSHA-specific configuration information You cannot configure the ASM using this command. After you connect to the image on the module using the attach module command, the prompt changes to module-number#.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example displays VSHA service group information for the ASM in slot 2.
module-2# show vsha sg-info
 ---------------------------------------------------------------------- 
		VSHA SG Table 
---------------------------------------------------------------------- 
System Variables: VmVsan=2, Real_IP=15.0.112.2     , interface_index=0x8080002 
---------------------------------------------------------------------- 
Record:0   VR_ID:1   SG_Name:sg-1   VR_IP:15.0.0.10       Node_ID:1 
Record:1   VR_ID:2   SG_Name:sg-2   VR_IP:15.0.0.11       Node_ID:2 
---------------------------------------------------------------------- 
module-4# show vsha sg-info vr_id 1 
---------------------------------------------------------------------- 
VSHA SG Table  
---------------------------------------------------------------------- 
System Variables: VmVsan=2, Real_IP=18.0.0.4       , interface_index=0x8180002 
Record: 0 
	VR_ID: 1 
	SG_Name: sg1 
	VR_IP: 18.0.0.24       
	Node_ID:1 
	State: VSHA_STANDALONE_MASTER 
	Arbitration_disk: 22000020374BB5990003.0000 
	Peer_IP: INVALID 
	Flags:0x0 
----------------------------------------------------------------------
module-4# show vsha dg-info vr_id 1
 ----------------------------------------------------------------------
VSHA-DG info for vr_id 1
 ----------------------------------------------------------------------
Record:0       DG_Name:rahul_dg1                          DG_state:DISK_GROUP_O
NLINE             
 ----------------------------------------------------------------------
module-4# show vsha sg-log vr_id 1
>>>>FSM: <VSHA_SG_1> has 35 logged transitions<<<<<
1) FSM:<VSHA_SG_1> Transition at 596109 usecs after Mon Apr  7 22:50:47 1980
    Previous state: [VSHA_NULL]
    Triggered event: [VSHA_EV_ARBITRATION_DISK_CHG]
    Next state: [VSHA_NULL]
2) FSM:<VSHA_SG_1> Transition at 163199 usecs after Mon Apr  7 22:51:13 1980
    Previous state: [VSHA_NULL]
    Triggered event: [VSHA_EV_ONLINE_SERVICE_GRP_AS_MASTER]
    Next state: [VSHA_STANDALONE_MASTER]
3) FSM:<VSHA_SG_1> Transition at 198675 usecs after Mon Apr  7 22:51:13 1980
    Previous state: [VSHA_STANDALONE_MASTER]
    Triggered event: [VSHA_EV_VX_DG_IMPORT_RESP]
    Next state: [VSHA_STANDALONE_MASTER]
4) FSM:<VSHA_SG_1> Transition at 201051 usecs after Mon Apr  7 22:51:23 1980
    Previous state: [VSHA_STANDALONE_MASTER]
    Triggered event: [VSHA_EV_RESOURCE_MONITOR]
    Next state: [VSHA_STANDALONE_MASTER]
attach module — terminal

To configure the terminal for the ASM, use the terminal command in attach module mode. Use the no form of the command to negate a previously-issued command or revert to factory defaults.

To connect to a ASM, use the attach module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attach session.

attach module slot-number
terminal length number-of-lines | session-timeout | terminal type | width integer]
Syntax Description

length

(Optional) Sets the number of lines on the screen.

number-of-lines

(Optional) Specifies the number of lines on the screen from 0 to 512. Enter 0 to scroll continuously.

session-timeout

(Optional) Specifies the session time out.

terminal-type

(Optional) Sets the terminal type.

width

(Optional) Sets the width of the display terminal, from 0 to 80.

integer

Sets the width of the display terminal, from 0 to 80.

Defaults

The default number of lines for the length is 24. The default width is 80 lines.

Command Modes

EXEC

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

Remember that all terminal parameter-setting commands are set locally and do not remain in effect after a session is ended. You must perform this task at the EXEC prompt at each session to see the debugging messages.

If the length is not 24 and the width is not 80, then you need to set a length and width.

Examples

The following example attaches to the ASM in slot 2 and exits from the ASM debug mode.
switch# attach module 2
Attaching to module 1 ...
To exit type 'exit', to abort type '$.' 
module-2# 
The following example enables the session timeout to 0 (will not time out) for the ASM in slot 2.
module-2# terminal session-timeout 0
attachpriv module

To connect to a ASM's Linux prompt, use the attachpriv module command in EXEC mode. To disconnect, use the exit command at the module-number# prompt, or type $. to forcibly abort the attach session.

attachpriv module slot-number
Syntax Description

attachpriv

Attaches to the Linux prompt.

module slot-number

Specifies the slot number for the ASM

Command Modes

EXEC

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

You cannot configure the ASM using this command. After you connect to the image on the module using the attachpriv module command, the prompt changes to vmroot@00:05:30:00:AC:AA:/root#.

You can only issue Linux-specific commands at this prompt.

This command only works with the ASM, not with any other type of module.

You must log into the supervisor module with admin privileges in order to run this command.

Caution The attachpriv module command is for troubleshooting, and should only be used by Cisco or Veritas support personnel. Do not attempt to configure the ASM at the Linux prompt.

Examples

The following example attaches to the ASM in slot 2 and connects to the Linux mode.
switch# attachpriv module 2
Attaching to asm 127.1.2.2
To exit type 'exit', to abort type '$.
vmroot@00:05:30:00:AC:AA:/root# 
asm mgmt-vsan

To assign the management VSAN for the Advanced Services Module (ASM), use the asm mgmt-vsan command. To revert to factory defaults or to negate a previously issued command, use the no form of the command.

asm mgmt-vsan vsan-id module slot-number
no asm mgmt-vsan vsan-id module slot-number
Syntax Description

asm

Configures the Advanced Services Module (ASM).

mgmt-vsan

Configures the management VSAN.

vsan-id

Specifies the ID of the management VSAN from 1 to 4093.

module slot-number

Specifies the slot number of the ASM.

Defaults

None.

Command Modes

Configuration mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

When you specify a management VSAN for the ASM, nine (9) fabric virtual (FV) interfaces are created

If you have configured trunking on both switches, you will see 18 FV interfaces instead of 9 FV interfaces.

After you configure the interface for a host port, you may set any other port-specific parameters, such as port type or mode.

Examples

The following example configures management VSAN 2 for the ASM in slot 2.
switch# config t
switch(config)# asm mgmt-vsan 2 module 2
Related Commands

Command

Description

show vsan

Displays all VSAN configurations.

show asm mgmt-vsan

Displays the configured management VSAN.

interface cpp

To configure a Control Plane Process (CPP) interface on the Cisco MDS 9000 Family of switches, use the interface cpp command. To disable a Fibre Channel interface, use the no form of the command.

interface cpp slot_number/processor-number/vsan-id
Syntax Description

interface

Configures a new interface.

cpp

Specifies the new interface to be a virtualization IPFC interface.

slot-number

Specifies a slot number of the ASM.

processor-number

Specifies the processor number for the IPFC interface. The current processor number is always 1.

vsan-id

Specifies the ID of the management VSAN from 1 to 4093.

Defaults

Disabled.

Command Modes

Configuration mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

You can specify a range of interfaces by issuing a command with the following example format:

interface space fc1/1space-space5space,spacefc2/5space-space7

Examples

The following example configures an IPFC interface for the ASM in slot 2 with a processor ID 1 in management VSAN 2.
switch# config t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# interface cpp 2/1/2
switch(config-if)#
Related Commands

Command

Description

show interface

Displays an interface configuration for a specified interface.

show asm

To displays configured information for the ASM, use the show asm command. To revert to factory defaults or to negate a previously issued command, use the no form of the command.

show asm disk-group | mgmt-vsan
Syntax Description

asm

Configures the Advanced Services Module (ASM).

mgmt-vsan

Configures the management VSAN.

vsan-id

Specifies the ID of the management VSAN from 1 to 4093.

module slot-number

Specifies the slot number of the ASM.

Defaults

None.

Command Modes

EXEC mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

None.

Examples

The following example displays the disk groups for the ASM in slot 2. Node refers to the ASM in slot 2 and SII refers to the SCSI index instance. When a disk group is created using the VERITAS Storage Foundation (TM) for Networks application, they are stored in the ASM.
switch# show asm disk-group
SII  Node   Disk Group Name
===  ====== ==========================
  3    2    dg1-114
  4    2    dg2-114
  5    2    dg1-112
  6    2    dg2-112
===  ====== ==========================
switch# show asm mgmt-vsan
Module-Id  Management VSAN
=========  ==================
  2            2
=========  ==================
Related Commands

Command

Description

asm mgmt-vsan

Configures the management VSAN.
show flogi database

show flogi database

To list all the FLOGI sessions through all interfaces across all VSANs, use the show flogi database command.

show flogi database [fcid fcid-id | interface interface | vsan vsan-id]
Syntax Description

fcid fcid-id

Displays FLOGI database entries based on the FC ID allocated.

interface interface

Displays FLOGI database entries based on the logged in interface.

vsan vsan-id

Displays FLOGI database entries based on the VSAN ID. The range is
1 to 4093.

Defaults

Displays the entire FLOGI database.

Command Modes

EXEC mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

FV interfaces are automatically created when the ASM boots up.

You can issue this command for a specific VSAN (management VSAN or discovery VSAN, or host VSAN using the VSAN ID, or you can use the FCID to view a specific interface's port name and node name. The symbolic port names and node names can only be displayed for a local device.

Examples

The following example displays the virtualization related FV interface information in the FLOGI database.
switch# show flogi database vsan 2
---------------------------------------------------------------------------
INTERFACE  VSAN    FCID            PORT NAME               NODE NAME
---------------------------------------------------------------------------
sup-fc0    2     0x6f0001  10:00:00:05:30:00:59:1f  20:00:00:05:30:00:59:1e
fv2/1/1    2     0x6f0002  10:00:00:05:30:00:59:20  20:00:00:05:30:00:59:1e
fv2/1/2    2     0x6f0003  23:02:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/1/3    2     0x6f000b  23:00:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/1/8    2     0x6f0000  10:00:00:00:5e:00:01:02  20:00:00:05:30:00:59:1e
fv2/1/9    2     0x6f000c  10:00:00:00:5e:00:01:01  20:00:00:05:30:00:59:1e
fv2/2/1    2     0x6f0004  23:03:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/3/1    2     0x6f0005  23:04:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/4/1    2     0x6f0006  23:05:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/5/1    2     0x6f0007  23:06:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/6/1    2     0x6f0008  23:07:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/7/1    2     0x6f0009  23:08:00:05:30:00:59:20  22:14:00:05:30:00:59:20
fv2/8/1    2     0x6f000a  23:09:00:05:30:00:59:20  22:14:00:05:30:00:59:20
show interface

You can check the status of an interface at any time by using the show interface command.

show interface
[interface range]
[brief | counters | description ]
[ cpp slot/process-number/vsan-id ] | [ fv slot/dpp-number/fv-port ]
[ fc slot/port ] | [ fc-tunnel tunnel-id ] |
[ fcip interface-number | gigabitethernet | iscsi ] |
mgmt | port-channel portchannel-number. subinterface-number | sup-fc | transceiver | trunk vsan [vsan-id] | vsan vsan-id
Syntax Description

interface range

Displays the interfaces in the specified range.

brief

Displays brief info of interface.

counters

Displays the interface counter information.

description

Displays a description of interface.

cpp slot/process-number/
vsan-id

Displays the virtualization IPFC interface in the specified slot along with the processor number and the VSAN ID.

fv slot/dpp-number/fv-port

Displays the virtual F port (FV port) interface in the specified slot along with the data path processor (DPP) number and the FV port number.

fc slot/port

Displays the Fibre Channel interface in the specified slot/port.

fc-tunnel tunnel-id

Displays description of the specified FC tunnel from 1 to 4095.

fcip interface-number

Displays the description of the specified FCIP interface from 1 to 255.

gigabitethernet slot/port

Displays the description of the Gigabit Ethernet interface in the specified slot/port.

iscsi slot/port

Displays the description of the iSCSI interface in the specified slot/ port.

mgmt

Displays the description of the management interface.

port-channel portchannel-number. subinterface-number

Displays the PortChannel interface specified by the PortChannel number followed by a dot (.) indicator and the subinterface number.

sup-fc

Displays the inband interface details.

transceiver

Displays the transceiver information for interface.

trunk vsan

Displays the trunking status of all VSANs.

vsan-id

Displays the trunking status of the specified VSANs.

vsan vsan-id

Displays the VSAN interface (brief, counters, or description for a specified interface or a range of interfaces)

Defaults

None

Command Modes

EXEC

Command History

This command was modified in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

The interface range must be in ascending order and nonoverlapping. You can specify a range using a hyphen and several interfaces using commas:

•The interface range format for a FC interface range is
fcslot/port - port , fcslot/port , fcslot/port
(For example, show int fc1/1 - 3 , fc1/5 , fc2/5)

•The interface range format for a FV interface range is
fvslot/dpp/fvport - fvport , fvslot/dpp/port , fvslot/dpp/port
(For example, show int fv2/1/1 - 3 , fv2/1/5 , fv2/2/5)

•The interface range format for a CPP interface range is
cppslot/process/vsan-id - vsan-id , cppslot/process/vsan-id , cppslot/process/vsan-id
(For example, show int cpp2/1/2 - 3 , cpp2/1/5 , cpp2/1/7)

•The format for a PortChannel is
port-channel portchannel-number. subinterface-number
(For example, show int port-channel portchannel-number. subinterface-number)

The CPP interface is configured when the IPFC interface is set up.

Examples
switch# show interface fc1/11
fc1/11 is up
    Hardware is Fibre Channel
    Port WWN is 20:0b:00:05:30:00:59:de
    Admin port mode is ST
    Port mode is ST
    Port vsan is 1
    Speed is 1 Gbps
    Rspan tunnel is fc-tunnel 100
    Beacon is turned off
    5 minutes input rate 248 bits/sec, 31 bytes/sec, 0 frames/sec
    5 minutes output rate 176 bits/sec, 22 bytes/sec, 0 frames/sec
      6862 frames input, 444232 bytes
        0 discards, 0 errors
        0 CRC, 0 unknown class
        0 too long, 0 too short
      6862 frames output, 307072 bytes
        0 discards, 0 errors
      0 input OLS, 0 LRR, 0 NOS, 0 loop inits
      0 output OLS, 0 LRR, 0 NOS, 0 loop inits
switch# show int fc1/1 - 3 , fc1/5 , fc2/5 brief
-------------------------------------------------------------------------------
Interface  Vsan   Admin  Admin   Status          FCOT   Oper  Oper   Port
                  Mode   Trunk                          Mode  Speed  Channel
                         Mode                                 (Gbps)
-------------------------------------------------------------------------------
fc1/1      3      auto   on      up               swl    FL      1    --
fc1/2      1      auto   on      fcotAbsent       --     --           --
fc1/3      1      auto   on      fcotAbsent       --     --           --
fc1/5      3      auto   on      notConnected     swl    --           --
fc2/5      5      FX     --      up               swl    F       2    --
switch# show int sup-fc0 
sup-fc0 is up
    Hardware is FastEthernet, address is 0000.0000.0000
    MTU 2596 bytes, BW 1000000 Kbit
    66 packets input, 7316 bytes
    Received 0 multicast frames, 0 compressed
    0 input errors, 0 frame, 0 overrun 0 fifo
    64 packets output, 28068 bytes, 0 underruns
    0 output errors, 0 collisions, 0 fifo
    0 carrier errors
switch# show int vsan 2
vsan2 is up, line protocol is up
    WWPN is 10:00:00:05:30:00:59:1f, FCID is 0xb90100
    Internet address is 10.1.1.1/24
    MTU 1500 bytes, BW 1000000 Kbit
    0 packets input, 0 bytes, 0 errors, 0 multicast
    0 packets output, 0 bytes, 0 errors, 0 dropped 
switch# show interface description
fc1/1
    no description
fc1/2
    no description
fc1/15
fcAnl
sup-fc0 is up
mgmt0 is up
vsan1 - IPFC interface
port-channel 15
no description
port-channel 98
no description
switch# show interface fc2/1 - 5 brief
-------------------------------------------------------------------------------
Interface  Vsan   Admin  Admin   Status           Oper  Oper   Port-channel
                  Mode   Trunk                    Mode  Speed
                         Mode                           (Gbps)
-------------------------------------------------------------------------------
fc1/1      3      auto   on      up               FL    1      --
fc1/2      1      auto   on      fcotAbsent       --           --
fc1/3      1      auto   on      fcotAbsent       --           --
fc1/4      3      auto   on      up               FL    1      --
fc1/5      3      auto   on      up               F     2      --
fc1/6      1      auto   on      fcotAbsent       --           --
fc1/7      1      auto   on      fcotAbsent       --           --
fc1/8      3      auto   on      fcotAbsent       --           --
fc1/9      1      auto   on      fcotAbsent       --           --
fc1/10     1      auto   on      fcotAbsent       --           --
fc1/11     1      auto   on      fcotAbsent       --           --
fc1/12     1      auto   on      fcotAbsent       --           --
fc1/13     1      auto   on      fcotAbsent       --           --
fc1/14     1      auto   on      fcotAbsent       --           --
fc1/15     1      auto   on      fcotAbsent       --           --
fc1/16     1      auto   on      trunking         TE    2      --
fc2/1      1      FX     --      fcotAbsent       --           --
fc2/2      1      FX     --      fcotAbsent       --           --
fc2/3      1      FX     --      fcotAbsent       --           --
fc2/4      1      FX     --      fcotAbsent       --           --
fc2/5      5      FX     --      up               F     2      --
...
-------------------------------------------------------------------------------
Interface          Status                            Speed
                                                     (Gbps)
-------------------------------------------------------------------------------
sup-fc0            up                                1
-------------------------------------------------------------------------------
Interface               Status     IP Address        Speed        MTU
-------------------------------------------------------------------------------
mgmt0                   up         172.22.36.112/23  100 Mbps     1500
-------------------------------------------------------------------------------
Interface          Status   IP Address               Speed        MTU
-------------------------------------------------------------------------------
vsan2                 up    15.0.112.0/16            1 Gbps       1500
-------------------------------------------------------------------------------
Interface          Status   IP Address               Speed        MTU
-------------------------------------------------------------------------------
cpp2/1/2              up    15.0.112.2/16            1 Gbps       1500
-------------------------------------------------------------------------------
Interface          VSAN     Status            Oper   Speed    Port-channel
                                              Mode
-------------------------------------------------------------------------------
fv2/1/1            2        up                F      auto     --
fv2/1/2            2        up                F      auto     --
fv2/1/3            2        up                F      auto     --
fv2/1/4            3        up                F      auto     --
fv2/1/5            3        up                F      auto     --
fv2/1/6            4        up                F      auto     --
...
switch# show interface fcip 3 counters
fcip3
    TCP Connection Information
      2 Active TCP connections
        Control connection: Local 43.1.1.2:3225, Remote 43.1.1.1:65532
        Data connection: Local 43.1.1.2:3225, Remote 43.1.1.1:65534
      30 Attempts for active connections, 0 close of connections
    TCP Parameters
      Path MTU 1500 bytes
      Current retransmission timeout is 300 ms
      Round trip time: Smoothed 10 ms, Variance: 5
      Advertised window: Current: 122 KB, Maximum: 122 KB, Scale: 1
      Peer receive window: Current: 114 KB, Maximum: 114 KB, Scale: 1
      Congestion window: Current: 2 KB, Slow start threshold: 1048560 KB
    5 minutes input rate 64 bits/sec, 8 bytes/sec, 0 frames/sec
    5 minutes output rate 64 bits/sec, 8 bytes/sec, 0 frames/sec
      910 frames input, 84652 bytes
         910 Class F frames input, 84652 bytes
         0 Class 2/3 frames input, 0 bytes
         0 Error frames timestamp error 0
      908 frames output, 84096 bytes
         908 Class F frames output, 84096 bytes
         0 Class 2/3 frames output, 0 bytes
         0 Error frames 0 reass frames
switch# show interface counters brief
-------------------------------------------------------------------------------
Interface          Input (rate is 5 min avg)      Output (rate is 5 min avg)
                   -----------------------------  -----------------------------
                   Rate     Total                 Rate     Total
                   MB/s     Frames                MB/s     Frames
-------------------------------------------------------------------------------
fc9/1              0        0                     0        0
fc9/2              0        0                     0        0
fc9/3              0        0                     0        0
fc9/4              0        0                     0        0
...
-------------------------------------------------------------------------------
Interface          Input (rate is 5 min avg)      Output (rate is 5 min avg)
                   -----------------------------  -----------------------------
                   Rate     Total                 Rate     Total
                   MB/s     Frames                MB/s     Frames
-------------------------------------------------------------------------------
iscsi4/1           0        0                     0        0
iscsi4/2           0        0                     0        0
iscsi4/3           0        0                     0        0
iscsi4/4           0        0                     0        0
...
vsan10 is up, line protocol is up
    WWPN is 10:00:00:05:30:00:07:23, FCID is 0xee0001
    Internet address is 10.1.1.5/24
    MTU 1500 bytes, BW 1000000 Kbit
    0 packets input, 0 bytes, 0 errors, 0 multicast
    0 packets output, 0 bytes, 0 errors, 0 dropped
-------------------------------------------------------------------------------
Interface          Input (rate is 5 min avg)      Output (rate is 5 min avg)
                   -----------------------------  -----------------------------
                   Rate     Total                 Rate     Total
                   MB/s     Frames                MB/s     Frames
-------------------------------------------------------------------------------
port-channel 100   0        0                     0        0
-------------------------------------------------------------------------------
Interface          Input (rate is 5 min avg)      Output (rate is 5 min avg)
                   -----------------------------  -----------------------------
                   Rate     Total                 Rate     Total
                   Mbits/s  Frames                Mbits/s  Frames
-------------------------------------------------------------------------------
fcip2              0        0                     0        0
fcip3              9        0                     9        0
fcip6              8        0                     8        0
fcip7              8        0                     8        0
switch# show interface fcip 3
fcip3 is trunking
    Hardware is GigabitEthernet
    Port WWN is 20:ca:00:05:30:00:07:1e
    Peer port WWN is 20:ca:00:00:53:00:18:1e
    Admin port mode is auto, trunk mode is on
    Port mode is TE
    vsan is 1
    Trunk vsans (allowed active) (1,10)
    Trunk vsans (operational)    (1)
    Trunk vsans (up)             (1)
    Trunk vsans (isolated)       (10)
    Trunk vsans (initializing)   ()
    Using Profile id 3 (interface GigabitEthernet4/3)
    Peer Information
      Peer Internet address is 43.1.1.1 and port is 3225
      Special Frame is disabled
    Maximum number of TCP connections is 2
    Time Stamp is disabled
    B-port mode disabled
    TCP Connection Information
      2 Active TCP connections
        Control connection: Local 43.1.1.2:3225, Remote 43.1.1.1:65532
        Data connection: Local 43.1.1.2:3225, Remote 43.1.1.1:65534
      30 Attempts for active connections, 0 close of connections
    TCP Parameters
      Path MTU 1500 bytes
      Current retransmission timeout is 300 ms
      Round trip time: Smoothed 10 ms, Variance: 5
      Advertized window: Current: 122 KB, Maximum: 122 KB, Scale: 1
      Peer receive window: Current: 114 KB, Maximum: 114 KB, Scale: 1
      Congestion window: Current: 2 KB, Slow start threshold: 1048560 KB
    5 minutes input rate 64 bits/sec, 8 bytes/sec, 0 frames/sec
    5 minutes output rate 64 bits/sec, 8 bytes/sec, 0 frames/sec
      866 frames input, 80604 bytes
         866 Class F frames input, 80604 bytes
         0 Class 2/3 frames input, 0 bytes
         0 Error frames timestamp error 0
      864 frames output, 80048 bytes
         864 Class F frames output, 80048 bytes
         0 Class 2/3 frames output, 0 bytes
         0 Error frames 0 reass frames
switch# show interface gigabitethernet 4/1
GigabitEthernet4/1 is up
    Hardware is GigabitEthernet, address is 0005.3000.2e12
    Internet address is 100.1.1.2/24
    MTU 1500 bytes, BW 1000000 Kbit
    Port mode is IPS
    Speed is 1 Gbps
    Beacon is turned off
    5 minutes input rate 32 bits/sec, 4 bytes/sec, 0 frames/sec
    5 minutes output rate 88 bits/sec, 11 bytes/sec, 0 frames/sec
    637 packets input, 49950 bytes
      0 multicast frames, 0 compressed
      0 input errors, 0 frame, 0 overrun 0 fifo
    659 packets output, 101474 bytes, 0 underruns
      0 output errors, 0 collisions, 0 fifo
      0 carrier errors
switch# show interface iscsi 2/1
iscsi2/1 is up
    Hardware is GigabitEthernet
    Port WWN is 20:41:00:05:30:00:50:de
    Admin port mode is ISCSI
    Port mode is ISCSI
    Speed is 1 Gbps
    iSCSI initiator is identified by name
    Number of iSCSI session: 7, Number of TCP connection: 7
    Configured TCP parameters
        Local Port is 3260
        PMTU discover is disabled
        Keepalive-timeout is 1 sec
        Minimum-retransmit-time is 300 ms
        Max-retransmissions 8
        Sack is disabled
        Minimum available bandwidth is 0 kbps
        Estimated round trip time is 0 usec
    5 minutes input rate 265184 bits/sec, 33148 bytes/sec, 690 frames/sec
    5 minutes output rate 375002168 bits/sec, 46875271 bytes/sec, 33833 frames/sec
    iSCSI statistics
      6202235 packets input, 299732864 bytes
        Command 6189718 pdus, Data-out 1937 pdus, 1983488 bytes, 0 fragments
      146738794 packets output, 196613551108 bytes
        Response 6184282 pdus (with sense 4), R2T 547 pdus
        Data-in 140543388 pdus, 189570075420 bytes
switch# show interface cpp 2/1/2
cpp2/1/2 is up, line protocol is up
    WWPN is 10:00:00:05:30:00:94:a0, FCID is 0x6d0002
    Internet address is 15.0.114.2/16
    MTU 1500 bytes, BW 1000000 Kbit
    4679361 packets input, 568734976 bytes, 0 errors, 1202625 multicast
    5000574 packets output, 584517419 bytes, 1 errors, 10 dropped
switch# show interface transceiver 
fc1/1 fcot is present but not supported
    name is IBM             
    part number is IBM42P21SNY     
    revision is AA20
    serial number is 53P148700109D   
    vendor specific data (bytes 96-127) 
      0x49 0x42 0x4D 0x20 0x53 0x46 0x50 0x53 
      0x20 0x41 0x52 0x45 0x20 0x43 0x4C 0x41 
      0x53 0x53 0x20 0x31 0x20 0x4C 0x41 0x53 
      0x45 0x52 0x20 0x53 0x41 0x46 0x45 0x20 
fc1/2 fcot not present
fc1/3 fcot is present but not supported
    name is IBM             
    part number is IBM42P21SNY     
    revision is AA20
    serial number is 53P1487000ZXR   
    vendor specific data (bytes 96-127) 
      0x49 0x42 0x4D 0x20 0x53 0x46 0x50 0x53 
      0x20 0x41 0x52 0x45 0x20 0x43 0x4C 0x41 
      0x53 0x53 0x20 0x31 0x20 0x4C 0x41 0x53 
      0x45 0x52 0x20 0x53 0x41 0x46 0x45 0x20 
switch# show interface fc-tunnel 200
fc-tunnel 200 is up 
Dest   IP Addr: 200.200.200.7   Tunnel ID: 200
Source IP Addr: 200.200.200.4   LSP ID: 1
Explicit Path Name: Path1
virt-112#  show interface fv 2/2/3
fv2/2/3 is up
    Hardware is Fibre Channel, WWN is 22:13:00:05:30:00:59:20
    Port mode is F
    Speed is auto
    vsan is 4
    Beacon is turned off
    0 packets input, 0 bytes, 0 discards
    0 input errors, 0 CRC, 0 invalid transmission words
        0 address id, 0 delimiter
    Received 0 runts, 0 jabber, 0 too long, 0 too short
        0 EOF abort, 0 fragmented, 0 unknown class
        0 OLS, 0 LRR, 0 NOS, 0 loop inits
    0 packets output, 0 bytes
    Transmitted 0 OLS, 0 LRR, 0 NOS, 0 loop inits
switch# show int fv2/1/2
fv2/1/2 is up
    Hardware is Fibre Channel, WWN is 22:0b:00:05:30:00:59:20
    Port mode is F
    Speed is auto
    vsan is 2
    Beacon is turned off
    0 packets input, 0 bytes, 0 discards
    0 input errors, 0 CRC, 0 invalid transmission words
        0 address id, 0 delimiter
    Received 0 runts, 0 jabber, 0 too long, 0 too short
        0 EOF abort, 0 fragmented, 0 unknown class
        0 OLS, 0 LRR, 0 NOS, 0 loop inits
    0 packets output, 0 bytes
    Transmitted 0 OLS, 0 LRR, 0 NOS, 0 loop inits
show fvport

You can check the status of a virtual F port (FV port) interface at any time by using the show fvport command.

show fvport [ interface fv slot/dpp-number/fv-port | interface range ]
Syntax Description

fvport

Displays all FV ports in the switch.

interface

Specifies the FV port interface.

fv slot/dpp-number/fv-port

Displays the FV port interface in the specified slot along with the data path processor (DPP) number and the FV port number.

interface range

Displays the interfaces in the specified range.

Defaults

None

Command Modes

EXEC

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.2(2).

Usage Guidelines

The interface range must be in ascending order and nonoverlapping. You can specify a range using a hyphen and several interfaces using commas. The interface range format for a FV interface range is
fvport interface fvslot/dpp/fvport - fvport , fvslot/dpp/port , fvslot/dpp/port
(For example, show fvport int fv2/1/1 - 3 , fv2/1/5 , fv2/2/5)

Examples
switch# show fvport
fv2/1/1
        The N Port if_index is     0x01090000
        The N Port pwwn is         10:00:00:05:30:00:59:20
        The N Port nwwn is         20:00:00:05:30:00:59:1e
        The vsan is                2
        The FV Port if_index is    0x0e080000
        The FV Port pwwn is        22:0a:00:05:30:00:59:20
        The DPP id is              0
        The NV port type is        IPFC
        The State is               ACTIVE
        Number of create requests
        minus the number of
        delete requests =          1
...
switch# show fvport interface fv2/4/1 , fv2/7/1 - 3
fv2/4/1
        The N Port if_index is     0x01094000
        The N Port pwwn is         23:05:00:05:30:00:59:20
        The N Port nwwn is         23:01:00:05:30:00:59:20
        The vsan is                2
        The FV Port if_index is    0x0e08c000
        The FV Port pwwn is        23:67:00:05:30:00:59:20
        The DPP id is              3
        The NV port type is        INTERNAL PORT
        The State is               ACTIVE
        Number of create requests
        minus the number of
        delete requests =          1
fv2/7/1
        The N Port if_index is     0x0108c000
        The N Port pwwn is         23:08:00:05:30:00:59:20
        The N Port nwwn is         23:01:00:05:30:00:59:20
        The vsan is                2
        The FV Port if_index is    0x0e098000
        The FV Port pwwn is        23:6a:00:05:30:00:59:20
        The DPP id is              6
        The NV port type is        INTERNAL PORT
        The State is               ACTIVE
        Number of create requests
        minus the number of
        delete requests =          1
fv2/7/2
        The N Port if_index is     0x0108d000
        The N Port pwwn is         23:1a:00:05:30:00:59:20
        The N Port nwwn is         23:46:00:05:30:00:59:20
        The vsan is                3
        The FV Port if_index is    0x0e098001
        The FV Port pwwn is        23:58:00:05:30:00:59:20
        The DPP id is              6
        The NV port type is        INTERNAL PORT
        The State is               ACTIVE
        Number of create requests
        minus the number of
        delete requests =          1
fv2/7/3
        The N Port if_index is     0x0108e000
        The N Port pwwn is         23:2c:00:05:30:00:59:20
        The N Port nwwn is         23:2e:00:05:30:00:59:20
        The vsan is                4
        The FV Port if_index is    0x0e098002
        The FV Port pwwn is        23:61:00:05:30:00:59:20
        The DPP id is              6
        The NV port type is        INTERNAL PORT
        The State is               ACTIVE
        Number of create requests
        minus the number of
        delete requests =          1