Table Of Contents

T Commands

tail

tcp-connection

tcp cwm

telnet

telnet server enable

terminal

time-stamp

traceroute

trunk protocol enable

T Commands

---

The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric switches. All commands are shown here in alphabetical order regardless of command mode. See the "Command Modes" section to determine the appropriate mode for each command. For more information, refer to the Cisco MDS 9000 Family Configuration Guide.

•tail

•tcp-connection

•tcp cwm

•telnet

•telnet server enable

•terminal

•time-stamp

•traceroute

•trunk protocol enable

tail

To display the last lines (tail end) of a specified file, use the tail command in EXEC mode.

tail filename [number-of-lines]

Syntax Description

filename	The name of the file for which you want to view the last lines.
number-of-lines	(Optional) The number of lines you want to view. If you do not specify the number of lines, the last 10 lines are displayed.

Defaults

None.

Command Modes

EXEC mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

You need two separate CLI terminals to use this command. In one terminal, execute the run-script or any other desired command. In the other, issue the tail command for the mylog file. In the second terminal, you will see the last lines of the mylog file (as it grows) that is being saved in response to the command issued in the first terminal.

If you specify a long file and would like to exit in the middle, enter Ctrl-c to exit this command.

Examples

The following example displays the last lines (tail end) of a specified file.

switch# run-script slot0:test mylog

In another terminal, issue the tail command for the mylog file.

switch# tail mylog

config t

In the second CLI terminal, you see the last lines of the mylog file (as it grows) that is being saved in response to the command issued in the first terminal.

tcp-connection

To configure the number of TCP connections for the FCIP interface, use the tcp-connection option. To revert to the default of two attempts, use the no form of the option.

tcp-connection number

no tcp-connection number

Syntax Description

tcp-connection	Configures the number of TCP connection attempts.
number	Enters the number of attempts (1 or 2).

Defaults

None.

Command Modes

Configuration mode

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.1(1).

Usage Guidelines

Access this command from the switch(config-if)# submode.

Use the tcp-connection option to specify the number of TCP connections from a FCIP link. By default, the switch tries two (2) TCP connections for each FCIP link.

Examples

switch# config t

switch(config)# interface fcip 50

switch(config-if)# tcp-connection 1

switch(config-if)# no tcp-connection 1

Related Commandss

Command	Description
show interface fcip	Displays an interface configuration for a specified FCIP interface.

tcp cwm

To configure congestion window monitoring (cwm) TCP parameters in a Cisco MDS 9000 Family switch, use the tcp cwm command. Use the no form of this command to disable this feature or revert to its factory defaults.

tcp cwm (burstsize burstsize)

no tcp cwm (burstsize burstsize)

Syntax Description

tcp	Configures TCP parameters for the FCIP profile.
cwm	Enables congestion monitoring.
burstsize	Configures TCP burstsize.
burstsize	Specifies the burstsize ranging from 10 to 100 KB.

Defaults

Enabled

Command Modes

Configuration mode—fcip profile submode

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.1(1).

Usage Guidelines

Use these TCP parameters to control TCP retransmission behavior in a switch.

Examples

The following example configures a FCIP profile and enables congestion monitoring.

switch## config t

switch(config)# fcip profile 5

switch(config-profile)# tcp cwm

The following example assigns the burstsize value at 20 KB:

switch(config-profile)# tcp cwm burstsize 20

The following example disables congestion monitoring.

switch(config-profile)# no tcp cwm

The following example leaves the CWM feature in an enabled state but changes the burstsize to the 
default of 10 KB.

switch(config-profile)# no tcp cwm burstsize 25

telnet

To log in to a host that supports Telnet, use the telnet command in EXEC mode.

telnet [hostname | ip-address]

Syntax Description

hostname	(Optional) Host name. Maximum length is 64 characters.
ip-address	(Optional) IP address Maximum length is 64 characters.

Defaults

None.

Command Modes

EXEC mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

None.

Examples

The following example establishes a Telnet session to the specified IP address.

switch# telnet 172.22.91.153

Trying 172.22.91.153...

Connected to 172.22.91.153.

Login:xxxxxxxx

Password:xxxxxxxxx

switch# 

telnet server enable

To enable the Telnet server if you wish to return to a Telnet connection from a secure SSH connection, use the telnet server enable command. To disable the Telnet server, use the no form of this command

telnet server enable

no telnet server enable

Syntax Description

This command has no arguments or keywords.

Defaults

Enabled.

Command Modes

Configuration mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

None.

Examples

The following example enables the Telnet server.

switch(config)# telnet server enable 

updated

switch(config)# no telnet server enable 

updated

Related Commands

Command	Description
telnet	Logs in to a host that supports Telnet.

terminal

To configure terminal attributes, use the terminal command in EXEC mode. To stop the display of syslog output, use the no form of the command.

terminal [length number-of-lines | monitor | terminal-type | unlock | width integer]

Syntax Description

length	(Optional) Sets the number of lines on the screen.
number-of-lines	(Optional) Specifies the number of lines on the screen from 0 to 512. Enter 0 to scroll continuously.
monitor	(Optional) Displays syslog output for the current terminal and session.
terminal-type	(Optional) Sets the terminal type.
width	(Optional) Sets the width of the display terminal, from 0 to 80.
integer	Sets the width of the display terminal, from 0 to 80.

Defaults

The default number of lines for the length is 24. The default width is 80 lines.

Command Modes

EXEC

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

Remember that all terminal parameter-setting commands are set locally and do not remain in effect after a session is ended. You must perform this task at the EXEC prompt at each session to see the debugging messages.

If the length is not 24 and the width is not 80, then you need to set a length and width.

Examples

The following example displays debug command output and error messages during the current terminal session.

switch# terminal monitor

Aug  8 10:32:42 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_CFG_PWRDN: Module 1 powered down

Aug  8 10:32:42 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_PWRDN: Module 1 powered down

Aug  8 10:32:42 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_INSERT: Module 1 has been inserted

Aug  8 10:33:12 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_PWRON: Module 1 powered up

Aug  8 10:33:13 sup48 % LOG_MODULE-5-MOD_REG_OK: LCM - Registration succeeded for module 1 

Aug  8 10:38:15 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_CFG_PWRDN: Module 1 powered down

Aug  8 10:38:15 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_INSERT: Module 1 has been inserted

Aug  8 10:38:45 sup48 % LOG_MODULE-5-MOD_REG_OK: LCM - Registration succeeded for module 1 

Aug  8 10:43:10 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_CFG_PWRDN: Module 1 powered down

Aug  8 10:43:10 sup48 % LOG_PLATFORM-5-PLATFORM_MOD_PWRDN: Module 1 powered down

......

The following example stops the current terminal monitoring session.

switch# terminal no monitor

time-stamp

To enable FCIP time stamps on a frame, use the time-stamp option. To disable this option for the selected interface, use the no form of the option.

time-stamp | acceptable-diff number

no time-stamp | acceptable-diff number

Syntax Description

time-stamp	Configures time-stamp.
acceptable-diff	Configures the acceptable time difference for time-stamps.
number	Enters the acceptable time from 1 to 60000.

Defaults

Disabled.

Command Modes

Configuration mode

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.1(1).

Usage Guidelines

Access this command from the switch(config-if)# submode.

The time-stamp option instructs the switch to discard frames that are older than a specified time.

Examples

switch# config t

switch(config)# interface fcip 50

switch(config-if)# time-stamp 

switch(config-if)# time-stamp acceptable-diff 4000

Related Commandss

Command	Description
show interface fcip	Displays an interface configuration for a specified FCIP interface.

traceroute

To print the route an IP packet takes to a network host, use the traceroute command in EXEC mode.

traceroute {hostname | ip-address}

Syntax Description

host name	The host name.
ip-address	The IP address.

Defaults

None.

Command Modes

EXEC mode.

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

This command traces the route an IP packet follows to an internet host by launching UDP probe packets with a small TTL (time to live) then listening for an ICMP (Internet Control Message Protocol) "time exceeded" reply from a gateway.

---

Note Probes start with a TTL of one and increase by one until encountering an ICMP "port unreachable." This means that the host was accessed or a maximum flag was hit. A line is printed showing the TTL, address of the gateway and round trip time of each probe. If the probe answers come from different gateways, the address of each responding system is printed.

---

Examples

The following example prints the route IP packets take to the network host www.cisco.com.

switch# traceroute www.cisco.com

traceroute to www.cisco.com (171.71.181.19), 30 hops max, 38 byte packets

 1  kingfisher1-92.cisco.com (172.22.92.2)  0.598 ms  0.470 ms  0.484 ms

 2  nubulab-gw1-bldg6.cisco.com (171.71.20.130)  0.698 ms  0.452 ms  0.481 ms

 3  172.24.109.185 (172.24.109.185)  0.478 ms  0.459 ms  0.484 ms

 4  sjc12-lab4-gw2.cisco.com (172.24.111.213)  0.529 ms  0.577 ms  0.480 ms

 5  sjc5-sbb4-gw1.cisco.com (171.71.241.174)  0.521 ms  0.495 ms  0.604 ms

 6  sjc12-dc2-gw2.cisco.com (171.71.241.230)  0.521 ms  0.614 ms  0.479 ms

 7  sjc12-dc2-cec-css1.cisco.com (171.71.181.5)  2.612 ms  2.093 ms  2.118 ms

 8  www.cisco.com (171.71.181.19)  2.496 ms *  2.135 ms

trunk protocol enable

To configure the trunk protocol, use the trunk protocol enable command in configuration mode. To disable the trunk protocol, use the no form of the command.

trunk protocol enable

no trunk protocol enable

Syntax Description

This command has no other arguments or keywords.

Command Modes

Configuration mode

Command History

This command was introduced in Cisco MDS SAN-OS Release 1.0(2).

Usage Guidelines

If the trunking protocol is disabled on a switch, no port on that switch can apply new trunk configurations. Existing trunk configurations are not affected—the TE port continues to function in trunking mode, but only supports traffic in VSANs that it negotiated previously (when the trunking protocol was enabled). Also, other switches that are directly connected to this switch are similarly affected on the connected interfaces. In some cases, you may need to merge traffic from different port VSANs across a non-trunking ISL. If so, you need to disable the trunking protocol.

Examples

The following example shows how to enable and disable the trunk protocol feature.

switch# config t

switch(config)# trunk protocol enable

switch(config)# no trunk protocol enable