Table Of Contents

Technical Specifications

Appliance Specifications

Adapter Specifications

Technical Specifications

---

This appendix describes the WAE models listed here:

Model	Product Number
Wide Area Application Engine 512	WAE-512-K9
Wide Area Application Engine 612	WAE-612-K9

This appendix contains the following sections:

•Appliance Specifications

•Adapter Specifications

Appliance Specifications

---

Note Your system software might not support all of the WAE-supported hardware features.

---

Table A-1 summarizes the features and specifications for the WAE-512 and WAE-612.

Table A-1 Appliance Features and Specifications 

Specification	Description
Microprocessor	•WAE-512—One Intel Pentium 4, 3.0-GHz processor 531, 800-MHz FSB1 , 1-MB level-2 cache •WAE-612—One Intel Pentium D Smithfield 3.0 GHz, Dual Core, 800-MHz FSB, 2-MB level-2 cache
Memory	•WAE-512—One, two, or four 1-GB RoHS compliant SDRAM RDIMMs The system comes with one 1-GB RDIMM. You have the option to add one or three additional 1-GB memory modules. •WAE-612—Two or four 1-GB RoHS compliant SDRAM RDIMMs The system comes with two 1-GB RDIMMs. You have the option to add two additional 1-GB memory modules.
Expansion bays	Two 3.5-in. (8.89-cm) slim-height bays for hard disk drives
Expansion slots	Two 64-bit, 100 MHz PCI-X half-length slots (1 low profile, 1 full profile)
Hard disk controllers	•WAE-512—Serial ATA (SATA) controller with integrated RAID (simple swap) •WAE-612—Serial-attached SCSI (SAS) controller with integrated RAID (hot swap)
Hard disk drives	•WAE-512—One or two 80-GB or 250-GB simple-swap serial advanced technology attachment (SATA) hard disk drives. Drive-type mixing is not allowed. •WAE-612—Two 146-GB or 300-GB serial attached SCSI (SAS). Drive-type mixing is not allowed.
Adapters	•1-port Fibre Channel adapter •1-port MPEG A/V decoder adapter •4-port Ethernet inline network adapter Note The WAE-512 and WAE-612 support full-height three-quarter-length adapter cards in PCI slot 1.
Power supply	1 AC-input
Dimensions	•Height: 1.75 in., 1 RU (43 mm) •Depth: 22 in. (559 mm) •Width: 17.32 in. (440 mm)
Weight	Maximum weight: 28 lb (12.7 kg) depending on your configuration
Electrical input	•Sine-wave input (47-63 Hz) required •Input voltage low range: –Minimum: 100 VAC –Maximum: 127 VAC •Input voltage high range: –Minimum: 200 VAC –Maximum: 240 VAC •Input kilovolt-amperes (kVA), approximately: –Minimum: 0.102 kVA –Maximum: 0.55 kVA
Ports Supported	•Two 1000BASE-TX, 100BASE-TX, 10BASE-T (dual) Ethernet ports •Serial port •Audio/video ports (on optional adapter): –3 BNC connectors –2 mini-XLR connectors
Temperature	•Operating: 50× to 95×F (10× to 35×C) •Nonoperating: -104× to 140×F (-40× to +60×C)
Heat Dissipation	•Minimum configuration: 307 Btu2 /hr (90 Watts) •Maximum configuration: 850 Btu/hr (250 Watts)
Humidity	•Operating: 8 to 80% •Nonoperating: 8 to 80%
Altitude	Maximum altitude: 6500 ft (2000 m)
Acoustical noise emissions	•Sound power, idling: 6.5 bel maximum •Sound power, operating: 6.5 bel maximum

1 FSB = front side bus 2 Btu = British thermal unit

Adapter Specifications

Table A-2 describes the Fibre Channel adapter specifications.

Table A-2 Fibre Channel Adapter Specifications

Fibre Channel adapter

•Bus type: Fiber-optic media (shortwave 50-micron) •Bus transfer rate: 2 gigabits per second (Gbps) maximum at half duplex and 4 Gbps at full duplex •Protocols: Supports FCP1 -SCSI protocol

1 FCP = Fibre Channel Protocol

Table A-3 describes the MPEG A/V decoder adapter specifications.

Table A-3 MPEG A/V Decoder Adapter Specifications

MPEG A/V decoder adapter

Video specifications •S/N:1 10 kHz to 4.2 MHz; Y: 65 dB rms2 ; Pb: 70 dB rms; Pr: 70 dB rms •Frequency response: 0 to 4.0 MHz ± 2 dB •Sync tip: 40 IRE3 ± 4 •Luma nonlinearity: 5% •Audio specifications •S/PDIF4 –PCM5 or compressed audio coding 3 (AC-3) bitstream out –75-ohm, 0.5-V p-p6 ± 20% –Rise and fall time: > 0.4 microseconds measured from 10 to 90% •Analog –Jumper-selectable balanced or unbalanced audio (balanced = +4 dBm) –Frequency response: 20 Hz to 22 kHz ± 0.5 dB –Reference level: 0.5-V p-p ± 10% –THD7 +n:@20 Hz to 22 kHz < 0.5%

1 S/N = signal-to-noise ratio 2 rms = root mean square 3 IRE = Institute of Radio Engineers 4 S/PDIF = Sony/Philips Digital Interface 5 PCM = pulse-coded modulation 6 p-p = peak to peak 7 THD = total harmonic distortion

Table A-4 describes the inline network adapter technical and general specifications.

---

Note The minimum software release required for the inline network adapter is WAAS 4.0.7.

---

Table A-4 Inline Network Adapter Specifications 

Specification	Description
Copper Gigabit Ethernet Specifications
IEEE standard	Gigabit Ethernet, 1000BASE-T Fast Ethernet, 100BASE-T Ethernet, 10BASE-T
Full duplex and half duplex	Supports both half-duplex and full-duplex operation in all operating speeds
Autonegotiation	Autonegotiates between full-duplex and half-duplex operations and between 1000-Mbps, 100-Mbps, and 10-Mbps speeds
Data transfer rate	1000-Mbps, 100-Mbps, and 10-Mbps speeds per port in half-duplex mode 2000-Mbps, 200-Mbps, and 20-Mbps speeds per port in full-duplex mode
General Technical Specifications
Interface standard	PCI v2.2 32/64 bit, 33/66 MHz PCI-X v1.0 32/64 bit, 66/100/133 MHz
Size	6.6 in. x 4.2 in. (167.64 mm x 106.68 mm)
PCI connector	Universal 64-bit connector
PCI voltage	+12V (minimum 11.4V, maximum 12.6V) +3.3V (minimum 3.0V, maximum 3.6V)
Weight	6.18 oz (175 grams)
Operating humidity	0 to 90 percent, noncondensing
Operating temperature	32× to -122× F (0× to 50× C)
Storage temperature	-4× to -149× F (-20× to -65× C)