Configuration de la technologie Hub and Spoke IPSec de routeur à routeur avec communication entre satellites

Options de téléchargement

  • PDF     (208.5 KB)
    Consulter à l'aide d'Adobe Reader sur un grand nombre d'appareils
  • ePub     (111.7 KB)
    Consulter à l’aide de différentes applications sur iPhone, iPad, Android ou Windows Phone
  • Mobi (Kindle)     (147.7 KB)
    Consulter sur un appareil Kindle ou à l’aide d’une application Kindle sur plusieurs appareils
Mis à jour:18 janvier 2007
ID du document:7912

Langage exempt de préjugés

Dans le cadre de la documentation associée à ce produit, nous nous efforçons d’utiliser un langage exempt de préjugés. Dans cet ensemble de documents, le langage exempt de discrimination renvoie à une langue qui exclut la discrimination en fonction de l’âge, des handicaps, du genre, de l’appartenance raciale de l’identité ethnique, de l’orientation sexuelle, de la situation socio-économique et de l’intersectionnalité. Des exceptions peuvent s’appliquer dans les documents si le langage est codé en dur dans les interfaces utilisateurs du produit logiciel, si le langage utilisé est basé sur la documentation RFP ou si le langage utilisé provient d’un produit tiers référencé. Découvrez comment Cisco utilise le langage inclusif.

À propos de cette traduction

Cisco a traduit ce document en traduction automatisée vérifiée par une personne dans le cadre d’un service mondial permettant à nos utilisateurs d’obtenir le contenu d’assistance dans leur propre langue. Il convient cependant de noter que même la meilleure traduction automatisée ne sera pas aussi précise que celle fournie par un traducteur professionnel.

Introduction

Cet exemple de configuration illustre une conception de réseau IPSec en étoile entre trois routeurs. Cette configuration diffère des autres configurations de réseau en étoile, car dans cet exemple, la communication est activée entre les sites en étoile en passant par le hub. En d'autres termes, il n'y a pas de tunnel IPsec direct entre les deux routeurs en étoile. Tous les paquets sont envoyés à travers le tunnel au routeur central qui les redistribue dans le tunnel IPsec partagé avec l'autre routeur en étoile. Cette configuration est possible suite à la résolution du bogue Cisco ID CSCdp09904 (clients enregistrés uniquement). Cette correction a été intégrée dans la version 12.2(5) du logiciel Cisco IOS® et cette version est la condition minimum requise pour cette configuration.

Afin de configurer le tunnel GRE (Generic Routing Encapsulation) sur IPSec avec OSPF, référez-vous à Configuration d'un tunnel GRE sur IPSec avec OSPF.

Afin de configurer la configuration de base du pare-feu Cisco IOS® sur un tunnel GRE avec traduction d'adresses de réseau (NAT), référez-vous à Configuration d'IPSec routeur à routeur (clés prépartagées) sur le tunnel GRE avec pare-feu IOS et NAT.

Conditions préalables

Conditions requises

Ce document exige une connaissance de base du protocole IPSec. Référez-vous à Introduction au cryptage de sécurité IP (IPSec) pour en savoir plus sur IPsec.

L'objectif de ce document est de s'assurer que le chiffrement est effectué entre ces routeurs :

  • 172.16.1.0/24 (Spoke 1) à 10.1.1.0/24 (Hub)

  • 192.168.1.0/24 (Spoke 2) à 10.1.1.0/24 (Hub)

  • 172.16.1.0/24 (Spoke 1) à 192.168.1.0/24 (Spoke 2)

Components Used

Les informations dans ce document sont basées sur les versions de logiciel et matériel suivantes :

  • Logiciel Cisco IOS Version 12.2(24a) (c2500-ik8s-l.122-24a.bin)

  • Routeurs Cisco 2500

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Pour plus d'informations sur les conventions utilisées dans ce document, reportez-vous à Conventions relatives aux conseils techniques Cisco.

Configuration

Cette section vous fournit des informations pour configurer les fonctionnalités décrites dans ce document.

Remarque : Utilisez l’outil de recherche de commandes (clients inscrits seulement) pour en savoir plus sur les commandes figurant dans le présent document.

Diagramme du réseau

Ce document utilise la configuration réseau indiquée dans le diagramme suivant.

VPNL2L.gif

Remarque : les schémas d'adressage IP utilisés dans cette configuration ne sont pas routables légalement sur Internet. Ce sont des adresses RFC 1918 qui ont été utilisés dans un environnement de laboratoire. leavingcisco.com

Configurations

Ce document utilise les configurations suivantes.

La commande show running-config affiche la configuration en cours sur le routeur.

Routeur concentrateur 
Hub#show running-config
Building configuration...
Current configuration : 1466 bytes
!
version 12.2

service timestamps debug datetime msec
service timestamps log uptime
no service password-encryption
!
hostname Hub
!


!
ip subnet-zero
!

!

!--- Configuration for IKE policies.

crypto isakmp policy 10

!--- Enables the IKE policy configuration (config-isakmp) !--- command mode, where you can specify the parameters that !--- are used during an IKE negotiation.

hash md5
authentication pre-share
crypto isakmp key cisco123 address 10.1.2.1
crypto isakmp key cisco123 address 10.1.3.1

!--- Specifies the preshared key "cisco123" which should !--- be identical at both peers. This is a global !--- configuration mode command.

 
!

!--- Configuration for IPsec policies.

crypto ipsec transform-set myset esp-des esp-md5-hmac 

!--- Enables the crypto transform configuration mode, !--- where you can specify the transform sets that are used !--- during an IPsec negotiation. 

!
crypto map mymap 10 ipsec-isakmp 

!--- Indicates that IKE is used to establish !--- the IPsec security association for protecting the !--- traffic specified by this crypto map entry.

set peer 10.1.2.1

!--- Sets the IP address of the remote end.

set transform-set myset 

!--- Configures IPsec to use the transform-set !--- "myset" defined earlier in this configuration.

match address 110

!--- Specifies the traffic to be encrypted.

crypto map mymap 20 ipsec-isakmp 
set peer 10.1.3.1
set transform-set myset 
match address 120
!
!
!
!
interface Ethernet0
ip address 10.1.1.1 255.255.255.0
!
interface Ethernet1
ip address 10.1.4.1 255.255.255.0
no ip route-cache

!--- You must enable process switching for IPsec !--- to encrypt outgoing packets. This command disables fast switching.

no ip mroute-cache
crypto map mymap

!--- Configures the interface to use the !--- crypto map "mymap" for IPsec.

!


!--- Output suppressed.

ip classless
ip route 172.16.1.0 255.255.255.0 Ethernet1
ip route 192.168.1.0 255.255.255.0 Ethernet1
ip route 10.1.0.0 255.255.0.0 Ethernet1
ip http server

!
access-list 110 permit ip 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 110 permit ip 192.168.1.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 120 permit ip 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 120 permit ip 172.16.1.0 0.0.0.255 192.168.1.0 0.0.0.255

!--- This crypto ACL-permit identifies the !--- matching traffic flows to be protected via encryption.

Routeur Spoke 1 
Spoke1#show running-config
Building configuration...
Current configuration : 1203 bytes
!
version 12.2

service timestamps debug datetime msec
service timestamps log uptime
no service password-encryption
!
hostname Spoke1
!
enable secret 5 $1$DOX3$rIrxEnTVTw/7LNbxi.akz0

!
ip subnet-zero
no ip domain-lookup
!

!
crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key cisco123 address 10.1.4.1
! 
!
crypto ipsec transform-set myset esp-des esp-md5-hmac 
!
crypto map mymap 10 ipsec-isakmp 
set peer 10.1.4.1
set transform-set myset 
match address 110
!
!
!
!
interface Ethernet0
ip address 172.16.1.1 255.255.255.0
!
interface Ethernet1
ip address 10.1.2.1 255.255.255.0
no ip route-cache
no ip mroute-cache
crypto map mymap
!

.
.

!--- Output suppressed.

.
.
ip classless

ip route 192.168.1.0 255.255.255.0 Ethernet1
ip route 10.1.0.0 255.255.0.0 Ethernet1
no ip http server

!
access-list 110 permit ip 172.16.1.0 0.0.0.255 10.1.1.0 0.0.0.255
access-list 110 permit ip 172.16.1.0 0.0.0.255 192.168.1.0 0.0.0.255
!

end
2509a#

Routeur Spoke 2 
Spoke2#show running-config
Building configuration...
Current configuration : 1117 bytes
!
version 12.2

service timestamps debug datetime msec
service timestamps log uptime
service password-encryption
!
hostname Spoke2
!

!
ip subnet-zero
no ip domain-lookup
!

!
crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key cisco123 address 10.1.4.1
!
! 
crypto ipsec transform-set myset esp-des esp-md5-hmac 
!
crypto map mymap 10 ipsec-isakmp 
set peer 10.1.4.1
set transform-set myset 
match address 120
!
!
!
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
!
interface Ethernet1
ip address 10.1.3.1 255.255.255.0

!--- No ip route-cache.

no ip mroute-cache
crypto map mymap
!

.
.

!--- Output suppressed.

.
.
ip classless

ip route 172.16.0.0 255.255.0.0 Ethernet1
ip route 10.1.0.0 255.255.0.0 Ethernet1
no ip http server

!
access-list 120 permit ip 192.168.1.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 120 permit ip 192.168.1.0 0.0.0.255 10.1.1.0 0.0.0.255
!

end
VPN2509#

Ajouter un autre rayon

Si vous devez ajouter un autre routeur en étoile (Spoke3) au routeur concentrateur existant en plus de Spoke1 et Spoke2, il suffit de créer un nouveau tunnel LAN à LAN (L2L) à partir du concentrateur vers Spoke3. Cependant, comme une seule carte de chiffrement peut être configurée par interface physique, vous devez utiliser le même nom de carte de chiffrement lors de l'ajout de ce tunnel. Cela est possible lorsque vous utilisez des numéros de ligne différents pour chaque site distant.

Remarque : Il peut être nécessaire de supprimer la carte de chiffrement et de la réappliquer à l'interface lorsque la nouvelle entrée de tunnel est ajoutée. Lorsque la carte de chiffrement est supprimée, tous les tunnels actifs sont effacés.

Routeur concentrateur 
Hub#show running-config
Building configuration...
Current configuration : 1466 bytes
!
version 12.2

service timestamps debug datetime msec
service timestamps log uptime
no service password-encryption
!
hostname Hub
!


!
ip subnet-zero
!

!
crypto isakmp policy 10

hash md5
authentication pre-share
crypto isakmp key cisco123 address 10.1.2.1
crypto isakmp key cisco123 address 10.1.3.1
crypto isakmp key cisco123 address 10.1.5.1
!

crypto ipsec transform-set myset esp-des esp-md5-hmac 
!
crypto map mymap 10 ipsec-isakmp 
set peer 10.1.2.1
set transform-set myset
match address 110

crypto map mymap 20 ipsec-isakmp 
set peer 10.1.3.1
set transform-set myset 
match address 120


!--- It is important to specify crypto map line number 30 for !--- the Spoke 3 router with the same crypto map name "mymap" 

crypto map mymap 30 ipsec-isakmp 
set peer 10.1.5.1
set transform-set myset 
match address 130
!
!
!
!
interface Ethernet0
ip address 10.1.1.1 255.255.255.0
!
interface Ethernet1
ip address 10.1.4.1 255.255.255.0
no ip route-cache
no ip mroute-cache


!--- It is important to remove and re-apply the crypto !--- map to this interface if it is used for the termination of other !--- spoke VPN tunnels.


crypto map mymap
!


!--- Output suppressed.

ip classless
ip route 172.16.1.0 255.255.255.0 Ethernet1
ip route 192.168.1.0 255.255.255.0 Ethernet1
ip route 10.1.0.0 255.255.0.0 Ethernet1
ip route 172.16.2.0 255.255.255.0 Ethernet1
ip http server

!
access-list 110 permit ip 10.1.1.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 110 permit ip 192.168.1.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 110 permit ip 172.16.2.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 120 permit ip 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 120 permit ip 172.16.2.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 120 permit ip 172.16.1.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 130 permit ip 10.1.1.0 0.0.0.255 172.16.2.0 0.0.0.255
access-list 130 permit ip 192.168.1.0 0.0.0.255 172.16.2.0 0.0.0.255
access-list 130 permit ip 172.16.1.0 0.0.0.255 172.16.2.0 0.0.0.255

Routeur Spoke 3 
Spoke3#show running-config
Building configuration...
Current configuration : 1117 bytes
!
version 12.2

service timestamps debug datetime msec
service timestamps log uptime
service password-encryption
!
hostname Spoke3
!

!
ip subnet-zero
no ip domain-lookup
!

!
crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key cisco123 address 10.1.4.1
!
! 
crypto ipsec transform-set myset esp-des esp-md5-hmac 
!
crypto map mymap 10 ipsec-isakmp 
set peer 10.1.4.1
set transform-set myset 
match address 130
!
!
!
!
interface Ethernet0
ip address 172.16.2.1 255.255.255.0
!
interface Ethernet1
ip address 10.1.5.1 255.255.255.0
no ip mroute-cache
crypto map mymap
!

.
.

!--- Output suppressed.

.
.
ip classless

ip route 172.16.0.0 255.255.0.0 Ethernet1
ip route 10.1.0.0 255.255.0.0 Ethernet1
no ip http server

!
access-list 130 permit ip 172.168.2.0 0.0.0.255 172.16.1.0 0.0.0.255
access-list 130 permit ip 172.168.2.0 0.0.0.255 10.1.1.0 0.0.0.255
access-list 130 permit ip 172.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255
!

end
VPN2509#

Vérification

Référez-vous à cette section pour vous assurer du bon fonctionnement de votre configuration.

L'Outil Interpréteur de sortie (clients enregistrés uniquement) (OIT) prend en charge certaines commandes show. Utilisez l'OIT pour afficher une analyse de la sortie de la commande show .

Afin de vérifier cette configuration, essayez une commande ping étendue provenant de l'adresse d'interface ethernet1 sur Spoke 1, destinée à l'adresse d'interface ethernet1 dans Spoke 2.

  • ping - Utilisé pour diagnostiquer la connectivité réseau de base. 

    Spoke1#ping
Protocol [ip]:
Target IP address: 192.168.1.1
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 172.16.1.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/64/68 ms

  • show crypto ipsec sa - Affiche les paramètres utilisés par les associations de sécurité (SA) IPSec actuelles.

  • show crypto isakmp sa — Affiche toutes les SA IKE en cours au niveau d'un homologue.

  • show crypto engine connections active : affiche le nombre de paquets transmis sur chaque SA IPSec.

Exemple de résultat de show

Ce résultat provient de la commande show crypto engine connections active exécutée sur le routeur Hub. 

Hub#show crypto engine connections active

ID Interface IP-Address State Algorithm Encrypt Decrypt
5 Ethernet0 10.1.4.1 set HMAC_MD5+DES_56_CB 0 0
6 <none> <none>  set HMAC_MD5+DES_56_CB 0 0
2000 Ethernet0 10.1.4.1 set HMAC_MD5+DES_56_CB 0 10
2001 Ethernet0 10.1.4.1 set HMAC_MD5+DES_56_CB 10 0
2002 Ethernet0 10.1.4.1 set HMAC_MD5+DES_56_CB 0 10
2003 Ethernet0 10.1.4.1 set HMAC_MD5+DES_56_CB 10 0

À partir de cet exemple, vous pouvez voir que chaque tunnel a chiffré et déchiffré 10 paquets, ce qui prouve que le trafic est passé par le routeur concentrateur.

Remarque : deux SA IPsec sont créées pour chaque homologue (une dans chaque direction). Par exemple, dans le routeur concentrateur, quatre SA IPsec sont créées pour deux homologues.

Dépannage

Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration.

Dépannage des commandes

Remarque : Consulter les renseignements importants sur les commandes de débogage avant d’utiliser les commandes de débogage.

Exemple de sortie de débogage

Il s'agit de la sortie du routeur concentrateur des commandes debug crypto ipsec et debug crypto isakmp. 

*Mar  1 00:03:46.887: ISAKMP (0:0): received packet 
  from 10.1.2.1 (N) NEW SA
*Mar  1 00:03:46.887: ISAKMP: local port 500, remote port 500
*Mar  1 00:03:46.899: ISAKMP (0:1): processing SA payload. message ID = 0
*Mar  1 00:03:46.899: ISAKMP (0:1): found peer pre-shared key matching 10.1.2.1
*Mar  1 00:03:46.903: ISAKMP (0:1): Checking ISAKMP transform 1 against priority
 10 policy
*Mar  1 00:03:46.903: ISAKMP:      encryption DES-CBC
*Mar  1 00:03:46.907: ISAKMP:      hash MD5
*Mar  1 00:03:46.907: ISAKMP:      default group 1
*Mar  1 00:03:46.911: ISAKMP:      auth pre-share
*Mar  1 00:03:46.911: ISAKMP:      life type in seconds
*Mar  1 00:03:46.911: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
*Mar  1 00:03:46.915: ISAKMP (0:1): atts are acceptable. Next payload is 0

!--- The initial IKE parameters have been !--- successfully exchanged between Spoke 1 and Hub.

*Mar  1 00:03:48.367: ISAKMP (0:1): SA is doing pre-shared key 
authentication using id type ID_IPV4_ADDR
*Mar  1 00:03:48.371: ISAKMP (0:1): sending packet to 10.1.2.1 (R) MM_SA_SETUP
*Mar  1 00:03:56.895: ISAKMP (0:1): received packet from 10.1.2.1 (R) MM_SA_SETUP
*Mar  1 00:03:56.899: ISAKMP (0:1): phase 1 packet is a duplicate of a previous packet.
*Mar  1 00:03:56.899: ISAKMP (0:1): retransmitting due to retransmit phase 1
*Mar  1 00:03:56.903: ISAKMP (0:1): retransmitting phase 1 MM_SA_SETUP...
*Mar  1 00:03:57.403: ISAKMP (0:1): retransmitting phase 1 MM_SA_SETUP...
*Mar  1 00:03:57.403: ISAKMP (0:1): incrementing error counter on sa: 
retransmit phase 1
*Mar  1 00:03:57.407: ISAKMP (0:1): retransmitting phase 1 MM_SA_SETUP
*Mar  1 00:03:57.407: ISAKMP (0:1): sending packet to 10.1.2.1 (R) 
 MM_SA_SETUP
*Mar  1 00:03:58.923: ISAKMP (0:1): received packet from 10.1.2.1 
 (R) MM_SA_SET UP
*Mar  1 00:03:58.931: ISAKMP (0:1): processing KE payload. message ID = 0
*Mar  1 00:04:00.775: ISAKMP (0:1): processing NONCE payload. message ID = 0
*Mar  1 00:04:00.783: ISAKMP (0:1): found peer pre-shared key matching 10.1.2.1
*Mar  1 00:04:00.795: ISAKMP (0:1): SKEYID state generated
*Mar  1 00:04:00.799: ISAKMP (0:1): processing vendor id payload
*Mar  1 00:04:00.803: ISAKMP (0:1): speaking to another IOS box!
*Mar  1 00:04:00.811: ISAKMP (0:1): sending packet to 10.1.2.1 (R) MM_KEY_EXCH
*Mar  1 00:04:02.751: ISAKMP (0:1): received packet from 10.1.2.1 (R) MM_KEY_EXCH
*Mar  1 00:04:02.759: ISAKMP (0:1): processing ID payload. message ID = 0
*Mar  1 00:04:02.759: ISAKMP (0:1): processing HASH payload. message ID = 0
*Mar  1 00:04:02.767: ISAKMP (0:1): SA has been authenticated with 10.1.2.1
*Mar  1 00:04:02.771: ISAKMP (1): ID payload
        next-payload : 8
        type         : 1
        protocol     : 17
        port         : 500
        length       : 8
*Mar  1 00:04:02.775: ISAKMP (1): Total payload length: 12
*Mar  1 00:04:02.783: ISAKMP (0:1): sending packet to 10.1.2.1 (R) QM_IDLE

*Mar  1 00:04:02.871: ISAKMP (0:1): received packet from 10.1.2.1 
 (R) QM_IDLE

!--- IKE phase 1 SA has been sucessfully negotiated !--- between Spoke 1 and Hub.

*Mar  1 00:04:02.891: ISAKMP (0:1): processing HASH payload. message ID = 581713929
*Mar  1 00:04:02.891: ISAKMP (0:1): processing SA payload. message ID = 581713929
*Mar  1 00:04:02.895: ISAKMP (0:1): Checking IPSec proposal 1

!--- IKE exchanges IPsec phase 2 parameters !--- between Spoke 1 and Hub.

*Mar  1 00:04:02.895: ISAKMP: transform 1, ESP_DES
*Mar  1 00:04:02.899: ISAKMP:   attributes in transform:
*Mar  1 00:04:02.899: ISAKMP:      encaps is 1
*Mar  1 00:04:02.899: ISAKMP:      SA life type in seconds
*Mar  1 00:04:02.903: ISAKMP:      SA life duration (basic) of 3600
*Mar  1 00:04:02.903: ISAKMP:      SA life type in kilobytes
*Mar  1 00:04:02.907: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
*Mar  1 00:04:02.911: ISAKMP:      authenticator is HMAC-MD5
*Mar  1 00:04:02.915: ISAKMP (0:1): atts are acceptable.

!--- IPsec phase 2 parameters have been !--- successfully exchanged between Spoke 1 and Hub.

*Mar  1 00:04:02.915: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 10.1.4.1, remote= 10.1.2.1,
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 0s and 0kb,
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4
*Mar  1 00:04:02.931: ISAKMP (0:1): processing NONCE payload. message ID = 581713929
*Mar  1 00:04:02.935: ISAKMP (0:1): processing ID payload. message ID = 581713929
*Mar  1 00:04:02.935: ISAKMP (0:1): processing ID payload. message ID = 581713929
*Mar  1 00:04:02.939: ISAKMP (0:1): asking for 1 spis from ipsec
*Mar  1 00:04:02.943: IPSEC(key_engine): got a queue event...
*Mar  1 00:04:02.951: IPSEC(spi_response): getting spi 4208568169 for SA
        from 10.1.4.1       to 10.1.2.1       for prot 3
*Mar  1 00:04:02.955: ISAKMP: received ke message (2/1)
*Mar  1 00:04:03.207: ISAKMP (0:1): sending packet to 10.1.2.1 (R) QM_IDLE

*Mar  1 00:04:03.351: ISAKMP (0:1): received packet from 10.1.2.1 (R) QM_IDLE

*Mar  1 00:04:03.387: ISAKMP (0:1): Creating IPSec SAs
*Mar  1 00:04:03.387:         inbound SA from 10.1.2.1 to 10.1.4.1
        (proxy 172.16.1.0 to 192.168.1.0)
*Mar  1 00:04:03.391:         has spi 0xFAD9A769 and conn_id 2000 and flags 4
*Mar  1 00:04:03.395:         lifetime of 3600 seconds
*Mar  1 00:04:03.395:         lifetime of 4608000 kilobytes
*Mar  1 00:04:03.399:         outbound SA from 10.1.4.1       to 10.1.2.1
  (proxy 192.168.1.0     to 172.16.1.0     )
*Mar  1 00:04:03.403:         has spi -732960388 and conn_id 2001 and flags C
*Mar  1 00:04:03.407:         lifetime of 3600 seconds
*Mar  1 00:04:03.407:         lifetime of 4608000 kilobytes
*Mar  1 00:04:03.411: ISAKMP (0:1): deleting node 581713929 error FALSE reason "
quick mode done (await()"
*Mar  1 00:04:03.415: IPSEC(key_engine): got a queue event...
*Mar  1 00:04:03.415: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 10.1.4.1, remote= 10.1.2.1,
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xFAD9A769(4208568169), conn_id= 2000, keysize= 0, flags= 0x4
*Mar  1 00:04:03.427: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 10.1.4.1, remote= 10.1.2.1,
    local_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xD44FE97C(3562006908), conn_id= 2001, keysize= 0, flags= 0xC
*Mar  1 00:04:03.443: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.4.1, sa_prot= 50,
    sa_spi= 0xFAD9A769(4208568169),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2000
*Mar  1 00:04:03.447: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.2.1, sa_prot= 50,
    sa_spi= 0xD44FE97C(3562006908),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2001

!--- IPsec tunnel has been created between !--- routers Spoke 1 and Hub.

*Mar  1 00:05:02.387: IPSEC(sa_request): ,

!--- Since an IPsec tunnel is created between Spoke 1 !--- and Spoke 2 through the Hub, the Hub router !--- initializes a new IPsec tunnel between itself and Spoke 2.

  (key eng. msg.) OUTBOUND local= 10.1.4.1, remote= 10.1.3.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0x1B7A414E(460996942), conn_id= 0, keysize= 0, flags= 0x400C
*Mar  1 00:05:02.399: ISAKMP: received ke message (1/1)
*Mar  1 00:05:02.403: ISAKMP: local port 500, remote port 500
*Mar  1 00:05:02.411: ISAKMP (0:2): beginning Main Mode exchange
*Mar  1 00:05:02.415: ISAKMP (0:2): sending packet to 10.1.3.1 
 (I) MM_NO_STATE
*Mar  1 00:05:12.419: ISAKMP (0:2): retransmitting phase 1 MM_NO_STATE...
*Mar  1 00:05:12.419: ISAKMP (0:2): incrementing error counter 
 on sa: retransmit phase 1
*Mar  1 00:05:12.423: ISAKMP (0:2): retransmitting phase 1 MM_NO_STATE
*Mar  1 00:05:12.423: ISAKMP (0:2): sending packet to 10.1.3.1 (I) 
 MM_NO_STATE
*Mar  1 00:05:22.427: ISAKMP (0:2): retransmitting phase 1 MM_NO_STATE...
*Mar  1 00:05:22.427: ISAKMP (0:2): incrementing error counter on sa: 
 retransmit phase 1
*Mar  1 00:05:22.431: ISAKMP (0:2): retransmitting phase 1 MM_NO_STATE
*Mar  1 00:05:22.431: ISAKMP (0:2): sending packet to 10.1.3.1 (I) 
 MM_NO_STATE
*Mar  1 00:05:22.967: ISAKMP (0:2): received packet from 10.1.3.1 
 (I) MM_NO_STATE
*Mar  1 00:05:22.975: ISAKMP (0:2): processing SA payload. message ID = 0
*Mar  1 00:05:22.975: ISAKMP (0:2): found peer pre-shared key 
 matching 10.1.3.1
*Mar  1 00:05:22.979: ISAKMP (0:2): Checking ISAKMP transform 1 
 against priority 10 policy
*Mar  1 00:05:22.979: ISAKMP:      encryption DES-CBC
*Mar  1 00:05:22.983: ISAKMP:      hash MD5
*Mar  1 00:05:22.983: ISAKMP:      default group 1
*Mar  1 00:05:22.987: ISAKMP:      auth pre-share
*Mar  1 00:05:22.987: ISAKMP:      life type in seconds
*Mar  1 00:05:22.987: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
*Mar  1 00:05:22.991: ISAKMP (0:2): atts are acceptable. 
 Next payload is 0

!--- IKE phase 1 parameters have been successfully !--- exchanged between Hub and Spoke 2.

*Mar  1 00:05:24.447: ISAKMP (0:2): SA is doing pre-shared key 
 authentication using id type ID_IPV4_ADDR
*Mar  1 00:05:24.455: ISAKMP (0:2): sending packet to 10.1.3.1 
 (I) MM_SA_SETUP
*Mar  1 00:05:26.463: ISAKMP (0:2): received packet from 10.1.3.1 
 (I) MM_SA_SETUP
*Mar  1 00:05:26.471: ISAKMP (0:2): processing KE payload. message ID = 0
*Mar  1 00:05:28.303: ISAKMP (0:2): processing NONCE payload. message ID = 0
*Mar  1 00:05:28.307: ISAKMP (0:2): found peer pre-shared key matching 10.1.3.1
*Mar  1 00:05:28.319: ISAKMP (0:2): SKEYID state generated
*Mar  1 00:05:28.323: ISAKMP (0:2): processing vendor id payload
*Mar  1 00:05:28.327: ISAKMP (0:2): speaking to another IOS box!
*Mar  1 00:05:28.331: ISAKMP (2): ID payload
        next-payload : 8
        type         : 1
        protocol     : 17
        port         : 500
        length       : 8
*Mar  1 00:05:28.335: ISAKMP (2): Total payload length: 12
*Mar  1 00:05:28.343: ISAKMP (0:2): sending packet to 10.1.3.1 (I) 
 MM_KEY_EXCH
*Mar  1 00:05:28.399: ISAKMP (0:2): received packet from 10.1.3.1 (I) 
 MM_KEY_EXCH
*Mar  1 00:05:28.407: ISAKMP (0:2): processing ID payload. message ID = 0
*Mar  1 00:05:28.411: ISAKMP (0:2): processing HASH payload. message ID = 0
*Mar  1 00:05:28.419: ISAKMP (0:2): SA has been authenticated with 10.1.3.1
*Mar  1 00:05:28.419: ISAKMP (0:2): beginning Quick Mode exchange, 
 M-ID of -1872859789
*Mar  1 00:05:28.439: ISAKMP (0:2): sending packet to 10.1.3.1 (I) QM_IDLE

*Mar  1 00:05:28.799: ISAKMP (0:2): received packet from 10.1.3.1 
(I) QM_IDLE

!--- The IKE phase 1 SA has been successfully !--- negotiated between Hub and Spoke 2.

*Mar  1 00:05:28.815: ISAKMP (0:2): processing HASH payload. 
 message ID = -1872859789
*Mar  1 00:05:28.815: ISAKMP (0:2): processing SA payload. 
 message ID = -1872859789
*Mar  1 00:05:28.819: ISAKMP (0:2): Checking IPSec proposal 1

!--- IKE exchanges IPsec phase 2 parameters !--- between Hub and Spoke 2.

*Mar  1 00:05:28.819: ISAKMP: transform 1, ESP_DES
*Mar  1 00:05:28.823: ISAKMP:   attributes in transform:
*Mar  1 00:05:28.823: ISAKMP:      encaps is 1
*Mar  1 00:05:28.827: ISAKMP:      SA life type in seconds
*Mar  1 00:05:28.827: ISAKMP:      SA life duration (basic) of 3600
*Mar  1 00:05:28.827: ISAKMP:      SA life type in kilobytes
*Mar  1 00:05:28.831: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
*Mar  1 00:05:28.835: ISAKMP:      authenticator is HMAC-MD5
*Mar  1 00:05:28.839: ISAKMP (0:2): atts are acceptable.

!--- IPsec phase 2 parameters have been successfully !--- exchanged between Hub and Spoke 2.

*Mar  1 00:05:28.843: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 10.1.4.1, remote= 10.1.3.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 0s and 0kb,
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4
*Mar  1 00:05:28.855: ISAKMP (0:2): processing NONCE payload. 
 message ID = -1872859789
*Mar  1 00:05:28.859: ISAKMP (0:2): processing ID payload. 
 message ID = -1872859789
*Mar  1 00:05:28.863: ISAKMP (0:2): processing ID payload. 
 message ID = -1872859789
*Mar  1 00:05:28.891: ISAKMP (0:2): Creating IPSec SAs
*Mar  1 00:05:28.891:         inbound SA from 10.1.3.1 to 10.1.4.1
        (proxy 192.168.1.0 to 172.16.1.0)
*Mar  1 00:05:28.895:         has spi 0x1B7A414E and conn_id 2002 and flags 4
*Mar  1 00:05:28.899:         lifetime of 3600 seconds
*Mar  1 00:05:28.899:         lifetime of 4608000 kilobytes
*Mar  1 00:05:28.903:         outbound SA from 10.1.4.1       to 10.1.3.1
  (proxy 172.16.1.0      to 192.168.1.0    )
*Mar  1 00:05:28.907:         has spi -385025107 and conn_id 2003 and flags C
*Mar  1 00:05:28.911:         lifetime of 3600 seconds
*Mar  1 00:05:28.911:         lifetime of 4608000 kilobytes
*Mar  1 00:05:28.915: ISAKMP (0:2): sending packet to 10.1.3.1 (I) QM_IDLE

*Mar  1 00:05:28.919: ISAKMP (0:2): deleting node -1872859789 error FALSE reason
 ""
*Mar  1 00:05:28.923: IPSEC(key_engine): got a queue event...
*Mar  1 00:05:28.927: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 10.1.4.1, remote= 10.1.3.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0x1B7A414E(460996942), conn_id= 2002, keysize= 0, flags= 0x4
*Mar  1 00:05:28.939: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 10.1.4.1, remote= 10.1.3.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xE90CFBAD(3909942189), conn_id= 2003, keysize= 0, flags= 0xC
*Mar  1 00:05:28.951: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.4.1, sa_prot= 50,
    sa_spi= 0x1B7A414E(460996942),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2002
*Mar  1 00:05:28.959: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.3.1, sa_prot= 50,
    sa_spi= 0xE90CFBAD(3909942189),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2003

!--- IPsec tunnel has been created between routers !--- Hub and Spoke 2. This establishes a tunnel between Spoke 1 !--- and Spoke 2 through Hub.

Ceci est la sortie du routeur Spoke 1 des commandes debug crypto isakmp et debug crypto ipsec. 

*Mar  1 00:03:28.771: IPSEC(sa_request): ,
  (key eng. msg.) OUTBOUND local= 10.1.2.1, remote= 10.1.4.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xD44FE97C(3562006908), conn_id= 0, keysize= 0, flags= 0x400C

!--- Request sent after the ping.

*Mar  1 00:03:28.787: ISAKMP: received ke message (1/1)
*Mar  1 00:03:28.791: ISAKMP: local port 500, remote port 500
*Mar  1 00:03:28.799: ISAKMP (0:1): beginning Main Mode exchange

!--- Initial IKE phase 1 parameters are exchanged !--- between Spoke 1 and Hub.

*Mar  1 00:03:28.803: ISAKMP (0:1): sending packet to 10.1.4.1 
 (I) MM_NO_STATE.
*Mar  1 00:03:38.807: ISAKMP (0:1): retransmitting phase 1 MM_NO_STATE...
*Mar  1 00:03:38.807: ISAKMP (0:1): incrementing error counter 
 on sa: retransmit phase 1
*Mar  1 00:03:38.811: ISAKMP (0:1): retransmitting phase 1 MM_NO_STATE
*Mar  1 00:03:38.811: ISAKMP (0:1): sending packet to 10.1.4.1 
 (I) MM_NO_STATE
*Mar  1 00:03:48.815: ISAKMP (0:1): retransmitting phase 1 MM_NO_STATE...
*Mar  1 00:03:48.815: ISAKMP (0:1): incrementing error counter on 
 sa: retransmit phase 1
*Mar  1 00:03:48.819: ISAKMP (0:1): retransmitting phase 1 MM_NO_STATE
*Mar  1 00:03:48.819: ISAKMP (0:1): sending packet to 10.1.4.1 (I) MM_NO_STATE
*Mar  1 00:03:49.355: ISAKMP (0:1): received packet from 10.1.4.1 
 (I) MM_NO_STATE
*Mar  1 00:03:49.363: ISAKMP (0:1): processing SA payload. message ID = 0
*Mar  1 00:03:49.363: ISAKMP (0:1): found peer pre-shared key matching 
 10.1.4.1
*Mar  1 00:03:49.367: ISAKMP (0:1): Checking ISAKMP transform 1 against 
 priority 10 policy
*Mar  1 00:03:49.367: ISAKMP:      encryption DES-CBC
*Mar  1 00:03:49.371: ISAKMP:      hash MD5
*Mar  1 00:03:49.371: ISAKMP:      default group 1
*Mar  1 00:03:49.375: ISAKMP:      auth pre-share
*Mar  1 00:03:49.375: ISAKMP:      life type in seconds
*Mar  1 00:03:49.375: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
*Mar  1 00:03:49.379: ISAKMP (0:1): atts are acceptable. 
 Next payload is 0

!--- IKE phase 1 parameters have been sucessfully !--- negotiated between Spoke 1 and Hub.

*Mar  1 00:03:50.835: ISAKMP (0:1): SA is doing pre-shared key 
 authentication using id type ID_IPV4_ADDR
*Mar  1 00:03:50.851: ISAKMP (0:1): sending packet to 10.1.4.1 
 (I) MM_SA_SETUP
*Mar  1 00:03:52.759: ISAKMP (0:1): received packet from 10.1.4.1 
 (I) MM_SA_SETUP
*Mar  1 00:03:52.763: ISAKMP (0:1): processing KE payload. message ID = 0
*Mar  1 00:03:54.635: ISAKMP (0:1): processing NONCE payload. message ID = 0
*Mar  1 00:03:54.639: ISAKMP (0:1): found peer pre-shared key matching 10.1.4.1
*Mar  1 00:03:54.651: ISAKMP (0:1): SKEYID state generated
*Mar  1 00:03:54.655: ISAKMP (0:1): processing vendor id payload
*Mar  1 00:03:54.663: ISAKMP (0:1): speaking to another IOS box!
*Mar  1 00:03:54.663: ISAKMP (1): ID payload
        next-payload : 8
        type         : 1
        protocol     : 17
        port         : 500
        length       : 8
*Mar  1 00:03:54.667: ISAKMP (1): Total payload length: 12
*Mar  1 00:03:54.675: ISAKMP (0:1): sending packet to 10.1.4.1 
 (I) MM_KEY_EXCH
*Mar  1 00:03:54.759: ISAKMP (0:1): received packet from 10.1.4.1 
 (I) MM_KEY_EXCH
*Mar  1 00:03:54.767: ISAKMP (0:1): processing ID payload. message ID = 0
*Mar  1 00:03:54.767: ISAKMP (0:1): processing HASH payload. message ID = 0
*Mar  1 00:03:54.775: ISAKMP (0:1): SA has been authenticated with 
 10.1.4.1
*Mar  1 00:03:54.779: ISAKMP (0:1): beginning Quick Mode exchange, 
 M-ID of 581713929
*Mar  1 00:03:54.799: ISAKMP (0:1): sending packet to 10.1.4.1 (I) QM_IDLE

*Mar  1 00:03:55.155: ISAKMP (0:1): received packet from 10.1.4.1 (I) QM_IDLE

*Mar  1 00:03:55.171: ISAKMP (0:1): processing HASH payload. 
 message ID = 581713929
*Mar  1 00:03:55.175: ISAKMP (0:1): processing SA payload. 
 message ID = 581713929
*Mar  1 00:03:55.179: ISAKMP (0:1): Checking IPSec proposal 1

!--- IKE exchanges the IPsec phase 2 parameters between !--- Spoke 1 and Hub.

*Mar  1 00:03:55.179: ISAKMP: transform 1, ESP_DES
*Mar  1 00:03:55.183: ISAKMP:   attributes in transform:
*Mar  1 00:03:55.183: ISAKMP:      encaps is 1
*Mar  1 00:03:55.183: ISAKMP:      SA life type in seconds
*Mar  1 00:03:55.187: ISAKMP:      SA life duration (basic) of 3600
*Mar  1 00:03:55.187: ISAKMP:      SA life type in kilobytes
*Mar  1 00:03:55.191: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
*Mar  1 00:03:55.195: ISAKMP:      authenticator is HMAC-MD5
*Mar  1 00:03:55.199: ISAKMP (0:1): atts are acceptable.

!--- IKE has successfully negotiated phase 2 IPsec !--- SA between Hub and Spoke 2.

*Mar  1 00:03:55.203: IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) INBOUND local= 10.1.2.1, remote= 10.1.4.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 0s and 0kb,
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4
*Mar  1 00:03:55.219: ISAKMP (0:1): processing NONCE payload. 
 message ID = 581713929
*Mar  1 00:03:55.219: ISAKMP (0:1): processing ID payload. 
 message ID = 581713929
*Mar  1 00:03:55.223: ISAKMP (0:1): processing ID payload. 
 message ID = 581713929
*Mar  1 00:03:55.251: ISAKMP (0:1): Creating IPSec SAs
*Mar  1 00:03:55.255:         inbound SA from 10.1.4.1 to 10.1.2.1
        (proxy 192.168.1.0 to 172.16.1.0)
*Mar  1 00:03:55.259:         has spi 0xD44FE97C and conn_id 2000 and flags 4
*Mar  1 00:03:55.263:         lifetime of 3600 seconds
*Mar  1 00:03:55.263:         lifetime of 4608000 kilobytes
*Mar  1 00:03:55.267:         outbound SA from 10.1.2.1       to 10.1.4.1
  (proxy 172.16.1.0      to 192.168.1.0    )
*Mar  1 00:03:55.271:         has spi -86399127 and conn_id 2001 and flags C
*Mar  1 00:03:55.271:         lifetime of 3600 seconds
*Mar  1 00:03:55.275:         lifetime of 4608000 kilobytes
*Mar  1 00:03:55.279: ISAKMP (0:1): sending packet to 10.1.4.1 (I) QM_IDLE

*Mar  1 00:03:55.283: ISAKMP (0:1): deleting node 581713929 error FALSE reason "
"
*Mar  1 00:03:55.287: IPSEC(key_engine): got a queue event...
*Mar  1 00:03:55.291: IPSEC(initialize_sas): ,
  (key eng. msg.) INBOUND local= 10.1.2.1, remote= 10.1.4.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xD44FE97C(3562006908), conn_id= 2000, keysize= 0, flags= 0x4
*Mar  1 00:03:55.303: IPSEC(initialize_sas): ,
  (key eng. msg.) OUTBOUND local= 10.1.2.1, remote= 10.1.4.1,
    local_proxy= 172.16.1.0/255.255.255.0/0/0 (type=4),
    remote_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac ,
    lifedur= 3600s and 4608000kb,
    spi= 0xFAD9A769(4208568169), conn_id= 2001, keysize= 0, flags= 0xC
*Mar  1 00:03:55.319: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.2.1, sa_prot= 50,
    sa_spi= 0xD44FE97C(3562006908),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2000
*Mar  1 00:03:55.323: IPSEC(create_sa): sa created,
  (sa) sa_dest= 10.1.4.1, sa_prot= 50,
    sa_spi= 0xFAD9A769(4208568169),
    sa_trans= esp-des esp-md5-hmac , sa_conn_id= 2001

!--- The IPsec tunnel between Spoke 1 and Hub is set up.

Informations connexes

Historique de révision

Révision Date de publication Commentaires
1.0
18-Jan-2007
Première publication

Ce document vous est-il utile?

FeedbackCommentaires

Contacter Cisco

Ce document s’applique à ces produits