Guest

Cisco Services Modules

Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Wireless LAN Services Module Software Release 2.6.0

  • Viewing Options

  • PDF (128.1 KB)
  • Feedback
Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Wireless LAN Services Module Software Release 2.6.0

Table Of Contents

Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Wireless LAN Services Module Software Release 2.6.0

Contents

System Requirements

Hardware Requirements

Software Requirements

Solution Requirements

WLSM Software Version to Cisco IOS Software Version Mapping

Limitations and Restrictions

Documentation Updates

Open and Resolved Caveats in Software Release 2.6.0

Open Caveats in Software Release 2.6.0

Resolved Caveats in Software Release 2.6.0

Related Documentation

Obtaining Documentation and Submitting a Service Request


Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Wireless LAN Services Module Software Release 2.6.0


September 2009

This publication describes the features, modifications, and caveats for the Catalyst 6500 series and Cisco 7600 series Wireless LAN Services Module (WLSM) software release 2.6.0.

This maintenance release does not introduce new features and does not resolve WLSM-related caveats. However, caveats were resolved in WDS, which affects the WLSM. Therefore, the purpose of this release is to maintain compatibility between WLSM software and access point WDS software.


Note For installation and configuration procedures for the WLSM, refer to the Catalyst 6500 series and Cisco 7600 series Wireless LAN Services Module documentation at this URL:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html


Contents

This document consists of these sections:

System Requirements

WLSM Software Version to Cisco IOS Software Version Mapping

Limitations and Restrictions

Documentation Updates

Open and Resolved Caveats in Software Release 2.6.0

Related Documentation

Obtaining Documentation and Submitting a Service Request

System Requirements

This section describes the system requirements for the Catalyst 6500 series and Cisco 7600 series WLSM software release 2.6.0:

Hardware Requirements

Software Requirements

Solution Requirements

Hardware Requirements

The wireless LAN software requires the following hardware:

Catalyst 6500 series switch or Cisco 7600 series router

Supervisor Engine 720

Catalyst 6500 series and Cisco 7600 series WLSM

Software Requirements

Table 1 lists the wireless LAN software versions supported by Cisco IOS software.

Table 1 Wireless LAN Software Compatibility

Product Number
Minimum WLAN Software Version
Recommended WLAN Software Version
Minimum Cisco IOS Software
 
Application Image
Maintenance Image
Application Image
Maintenance Image
 

WS-SVC-WLAN-1-K9 with Supervisor Engine 720

1.1.1

3.1(1)

2.1.1

3.1(1)

12.2(18)SXF2


Solution Requirements

In addition to the hardware and software requirements, the WLSM also requires the following:

Cisco Aironet 1100, 1130AG, 1200, 1230AG, and 1240AG Series Access Points and Cisco Aironet 1300 Series Outdoor Access Point/Bridge using Cisco IOS Release 12.2(15)XR or Release 12.3(2)JA or later, Cisco Aironet 1130 Series Access Point using Cisco IOS Release 12.3(2)JA or later, or Cisco Aironet 1310 Outdoor Access Point/Bridge (configured in access point mode) using Cisco IOS Release 12.3(2)JA or later

CiscoWorks Wireless LAN Solution Engine (WLSE) release 2.7(1) or later

WLSM Software Version to Cisco IOS Software Version Mapping

Table 2 shows the mapping between WLSM software versions and Cisco IOS Software versions.

Table 2 WLSM Software Version to Cisco IOS Software Version Mapping 

WLSM Image Version
Cisco IOS Software Version

2.6.0

12.3(8)JEC1

2.5.0

12.3(8)JEC1

2.4.1

12.3(8)JEB1

2.4.0

12.3(8)JEB

2.3.1

12.3(8)JEA1

2.2.1

12.3(8)JEA

2.1.1

12.3(8)JA

1.4.3 (deferred)

12.3(7)JA2

1.4.2 (deferred)

12.3(7)JA1

1.4.1 (deferred)

12.3(7)JA

1.3.2 (deferred)

12.3(4)JA1

1.3.1 (deferred)

12.3(4)J

1.2.3 (deferred)

12.3(2)JA5

1.2.2 (deferred)

12.3(2)JA2

1.2.1 (deferred)

12.3(2)JA

1.1.2 (deferred)

12.2(15)XR2

1.1.1 (deferred)

12.2(15)XR1


Limitations and Restrictions

This section describes general limitations and restrictions:

In software release 1.1.1 through 1.4.1, you can install one WLSM in a chassis.

In software release 2.1.1, you can install two WLSMs, which requires Cisco IOS Release 12.2(18)SXF2.

You cannot configure wireless clients in the same subnet as wired clients.

You cannot map multiple SSIDs to a single network ID.

You cannot configure QoS on tunnel interfaces in systems with a PFC3A. There is full QoS support in systems with a PFC3B or PFC3BXL.

If you upgrade your Supervisor 720 to Cisco IOS Release 12.2(18)SFX2, you must be running Cisco Wireless LAN Services Module software version 1.4.3 or greater on your WLSM.

Documentation Updates

The Cisco Catalyst 6500 Series Wireless LAN Services Module: Detailed Design and Implementation Guide contains an incorrect entry pertaining to default gateway IP addresses

The WLSM Failover—The "DHCP Configuration" section on page 56 states that the DHCP server must be configured to return both IP address to the client. This is not correct because the specific default gateway that a client uses is ignored by the access point and all traffic is sent to the upstream tunnel address. The tunnel address changes after the access point registers with the backup WDS and new tunnels are created by its corresponding Supervisor 720 module. Only one gateway is needed.

This discrepancy is documented in open caveat CSCej53619.

Open and Resolved Caveats in Software Release 2.6.0

These sections describe open and resolved caveats in Wireless LAN software release 2.6.0:

Open Caveats in Software Release 2.6.0

Resolved Caveats in Software Release 2.6.0

Open Caveats in Software Release 2.6.0

CSCsm71956—When you use the local radius server on a WDS master access point for infrastructure access point authentication and use other radius servers for client authentications, client and infrastructure access point authentications fail to pass through the WDS master access point if the primary radius server for client authentication is down and the WDS master access point is rebooted. In addition, the WLCCP WDS process may start to hold onto memory.

Workaround: Remove the Radius server that is no longer responding from the configuration. This workaround causes issues if you are using Radius server failover but it allows client and infrastructure authentications to pass.

CSCsm94076—The output of the show wlccp wnm status command on an 1130 series access point running Cisco IOS Software release 12.4(10b)JA shows that the access point and the WLSE are not authenticated.

Workaround: Enable all radio interfaces so that they are listed as up in the output of the show ip interfaces brief command. Leave them up until the WLCCP link displays SECURITY_KEYS_SETUP; then you can shut down any radio interfaces. After a reboot the SECURITY_KEYS_SETUP remains.

Resolved Caveats in Software Release 2.6.0

No caveats are resolved in this release.

Related Documentation

For additional information about Catalyst 6500 series switches and command-line interface (CLI) commands, refer to the following:

Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches

Catalyst 6500 Series Switch Installation Guide

Catalyst 6500 Series Switch Module Installation Guide

Catalyst 6500 Series Switch Software Configuration Guide

Catalyst 6500 Series Switch Command Reference

Catalyst 6500 Series System Message Guide

Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide

Catalyst 6500 Series Switch Cisco IOS Command Reference

Release Notes for Cisco IOS Release 12.2SX on the Catalyst 6500 and Cisco 7600 Supervisor Engine 720

For information about MIBs, refer to this URL:

http://www.cisco.com/cisco/software/navigator.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.