Interface Command Reference Guide, Cisco IOS XE Release 3 SE (Cisco 5700 Series WLC)
Interface Commands
Downloads: This chapterpdf (PDF - 1.59MB) The complete bookPDF (PDF - 2.48MB) | The complete bookePub (ePub - 182.0KB) | Feedback

Interface Commands

Interface Commands

This chapter displays the following commands:

client vlan

To configure a wireless LAN interface, use the client vlan command. To remove a wireless LAN interface, use the no form of the command.

client vlan interface-name

no client vlan

Syntax Description

vlan interface-name

Specifies the name of the interface.

Command Default

Disabled

Command Modes

Configuration mode

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure vlan10 on an interface:

Controller# client vlan vlan10

clear nmsp statistics

To clear the Network Mobility Services Protocol (NMSP) statistics, use the clear nmsp statistics command in privileged EXEC mode.

clear nmsp statistics

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to clear NMSP statistics:


         
         Controller# clear nmsp statistics

You can verify that information was deleted by entering the show nmsp statistics privileged EXEC command.

debug ilpower

To enable debugging of the power controller and Power over Ethernet (PoE) system, use the debug ilpower command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug ilpower { cdp | controller | event | ha | ipc | police | port | powerman | registries | scp | sense }

no debug ilpower { cdp | controller | event | ha | ipc | police | port | powerman | registries | scp | sense }

Syntax Description

cdp

Displays PoE Cisco Discovery Protocol (CDP) debug messages.

controller

Displays PoE controller debug messages.

event

Displays PoE event debug messages.

ha

Displays PoE high-availability messages.

ipc

Displays PoE Inter-Process Communication (IPC) debug messages.

police

Displays PoE police debug messages.

port

Displays PoE port manager debug messages.

powerman

Displays PoE power management debug messages.

registries

Displays PoE registries debug messages.

scp

Displays PoE SCP debug messages.

sense

Displays PoE sense debug messages.

Command Default

Debugging is disabled.

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Cisco IOS XE 3.3SE

The upoe keyword was added.

Usage Guidelines

This command is supported only on PoE-capable switches.

When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.

debug interface

To enable debugging of interface-related activities, use the debug interface command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug interface { interface-id | counters { exceptions | protocol memory } | null interface-number | port-channel port-channel-number | states| vlan vlan-id }

no debug interface { interface-id | counters { exceptions | protocol memory } | null interface-number | port-channel port-channel-number | states| vlan vlan-id }

Syntax Description

interface-id

ID of the physical interface. Displays debug messages for the specified physical port, identified by type switch number/module number/port, for example, gigabitethernet 1/0/2.

null interface-number

Displays debug messages for null interfaces. The interface number is always 0.

port-channel port-channel-number

Displays debug messages for the specified EtherChannel port-channel interface. The port-channel-number range is 1 to 48.

vlan vlan-id

Displays debug messages for the specified VLAN. The vlan range is 1 to 4094.

counters

Displays counters debugging information.

exceptions

Displays debug messages when a recoverable exceptional condition occurs during the computation of the interface packet and data rate statistics.

protocol memory

Displays debug messages for memory operations of protocol counters.

states

Displays intermediary debug messages when an interface's state transitions.

Command Default

Debugging is disabled.

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

If you do not specify a keyword, all debug messages appear.

The undebug interface command is the same as the no debug interface command.

When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.

debug lldp packets

To enable debugging of Link Layer Discovery Protocol (LLDP) packets, use the debug lldp packets command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug lldp packets

no debug lldp packets

Syntax Description

This command has no arguments or keywords.

Command Default

Debugging is disabled.

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

The undebug lldp packets command is the same as the no debug lldp packets command.

When you enable debugging on a switch stack, it is enabled only on the . To enable debugging on a stack member, you can start a session from the by using the session switch-number EXEC command.

debug platform fallback-bridging

To enable debugging of the platform-dependent fallback bridging manager, use the debug platform fallback-bridging command in EXEC mode. To disable debugging, use the no form of this command.

debug platform fallback-bridging [ error | retry | rpc { events | messages } ]

no debug platform fallback-bridging [ error | retry | rpc { events | messages } ]

Syntax Description

error

(Optional) Displays fallback bridging manager error condition messages.

retry

(Optional) Displays fallback bridging manager retry messages.

rpc {events | messages}

(Optional) Displays fallback bridging debugging information. The keywords have these meanings:

  • events—Displays remote procedure call (RPC) events.
  • messages —Displays RPC messages.

Command Default

Debugging is disabled.

Command Modes

User EXEC

Privileged EXEC

Command History

Release

Modification

15.0

This command was introduced.

Usage Guidelines

If you do not specify a keyword, all fallback bridging manager debug messages appear.

The undebug platform fallback-bridging command is the same as the no debug platform fallback-bridging command.

When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.

Related Commands

Command

Description

show debugging

Displays information about the types of debugging that are enabled.

duplex

To specify the duplex mode of operation for a port, use the duplex command in interface configuration mode. To return to the default value, use the no form of this command.

duplex { auto | full | half }

no duplex { auto | full | half }

Syntax Description

auto

Enables automatic duplex configuration. The port automatically detects whether it should run in full- or half-duplex mode, depending on the attached device mode.

full

Enables full-duplex mode.

half

Enables half-duplex mode (only for interfaces operating at 10 or 100 Mb/s). You cannot configure half-duplex mode for interfaces operating at 1000 or 10,000 Mb/s.

Command Default

The default is auto for Gigabit Ethernet ports.

You cannot configure the duplex mode on 10-Gigabit Ethernet ports; it is always full.

Duplex options are not supported on the 1000BASE-x or 10GBASE-x (where -x is -BX, -CWDM, -LX, -SX, or -ZX) small form-factor pluggable (SFP) modules.

Command Modes

Interface configuration

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

For Gigabit Ethernet ports, setting the port to auto has the same effect as specifying full if the attached device does not autonegotiate the duplex parameter.


Note


Half-duplex mode is supported on Gigabit Ethernet interfaces if the duplex mode is auto and the connected device is operating at half duplex. However, you cannot configure these interfaces to operate in half-duplex mode.


Certain ports can be configured to be either full duplex or half duplex. How this command is applied depends on the device to which the switch is attached.

If both ends of the line support autonegotiation, we highly recommend using the default autonegotiation settings. If one interface supports autonegotiation and the other end does not, configure duplex and speed on both interfaces, and use the auto setting on the supported side.

If the speed is set to auto, the switch negotiates with the device at the other end of the link for the speed setting and then forces the speed setting to the negotiated value. The duplex setting remains as configured on each end of the link, which could result in a duplex setting mismatch.

You can configure the duplex setting when the speed is set to auto.


Caution


Changing the interface speed and duplex mode configuration might shut down and reenable the interface during the reconfiguration.


You can verify your setting by entering the show interfaces privileged EXEC command.

Examples

This example shows how to configure an interface for full-duplex operation:

Controller(config)# interface gigabitethernet1/0/1
Controller(config-if)# duplex full

interface

To configure an interface, use the interface command.

interface { Auto-Template Auto-Template interface-number | Capwap Capwap interface-number | Gigabit Ethernet Gigabit Ethernet interface number | Group VI Group VI interface number Internal Interface Internal Interface number Loopback Loopback interface number Null Null interface Port-channel interface number Port-channel interface number TenGigabit Ethernet interface number Tunnel interface number Vlan interface number }

Syntax Description

Auto-Template Auto-template interface-number

Enables you to configure auto-template interface. Values range from 1 to 999.

Capwap Capwap interface number

Enables you to configure CAPWAP tunnel interface. Values range from 0 to 2147483647.

GigabitEthernet Gigabit Ethernet interface number

Enables you to configure Gigabit Ethernet IEEE 802.3z interface. Values range from 0 to 9.

Group VI Group VI interface number

Enables you to configure the internal interface. Values range from 0 to 9.

Internal Interface Internal Interface

Enables you to configure internal interface.

Loopback Loopback Interface number

Enables you to configure loopback interface. Values range from 0 to 2147483647.

Null Null interface number

Enables you to configure null interface. Value is 0.

Port-channel interface number

Enables you to configure Ethernet channel interfaces. Values range from 1 to 128.

TenGigabitEthernet interface number

Enables you to configure a 10-Gigabit Ethernet interface. Values range from 0 to 9.

Tunnel interface number

Enables you to configure the tunnel interface. Values range from 0 to 2147483647.

Vlan interface number

Enables you to configure switch VLAN interfaces. Values range from 0 to 4098.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You can not use the "no" form of this command.

Examples

This example shows how you can configure interface:

Controller# interface Tunnel 15

interface auto-template

To configure an auto-template interface, use the interface auto-template command.

interface auto-template interface-name

Syntax Description

interface-name

Specifies the interface number.

Command Default

Disabled

Command Modes

Global configuration mode

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure interface auto-template:

# interface auto-template
                                             
                                             

interface range

To configure an interface range, use the interface range command.

interface range { Gigabit Ethernet interface-number | | Loopback interface-number | Port Channel interface-number | TenGigabit Ethernet interface-number Tunnel interface-number Vlan interface-number Macro WORD }

Syntax Description

GigabitEthernet interface-number

Configures the Gigabit Ethernet IEEE 802.3z interface. Values range from 1 to 9.

Loopback interface-number

Configures the loopback interface. Values range from 0 to 2147483647.

Port-Channel interface-number

Configures 10-Gigabit Ethernet channel of interfaces. Values range from 1 to 128.

TenGigabit Ethernet interface-number

Configures 10-Gigabit Ethernet interfaces. Values range from 0 to 9.

Tunnel interface-number

Configures the tunnel interface. Values range from 0 to 2147483647.

VLAN interface-number

Configures the switch VLAN interfaces. Values range from 1 to 4095.

Macro WORD

Configures the keywords to interfaces. Support up to 32 characters.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how you can configure interface range:

Controller(config)# interface range vlan 1

location

To configure location information for an endpoint, use the location command in global configuration mode. To remove the location information, use the no form of this command.

location { admin-tag string | civic-location identifier { host | id } | elin-location string identifier id | geo-location identifier { host | id } }

no location { admin-tag string | civic-location identifier { host | id } | elin-location string identifier id | geo-location identifier { host | id } }

Syntax Description

admin-tag

Configures administrative tag or site information.

string

Site or location information in alphanumeric format.

civic-location

Configures civic location information.

identifier

Specifies the name of the civic location, emergency, or geographical location.

host

Defines the host civic or geo-spatial location.

id

Name of the civic, emergency, or geographical location.

Note   

The identifier for the civic location in the LLDP-MED controller TLV is limited to 250 bytes or less. To avoid error messages about available buffer space during controller configuration, be sure that the total length of all civic-location information specified for each civic-location identifier does not exceed 250 bytes.

elin-location

Configures emergency location information (ELIN).

geo-location

Configures geo-spatial location information.

Command Default

None

Command Modes

Global configuration

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

After entering the location civic-location identifier global configuration command, you enter civic location configuration mode. After entering the location geo-location identifier global configuration command, you enter geo location configuration mode.

The civic-location identifier must not exceed 250 bytes.

The host identifier configures the host civic or geo-spatial location. If the identifier is not a host, the identifier only defines a civic location or geo-spatial template that can be referenced on the interface.

The host keyword defines the device location. The civic location options available for configuration using the identifier and the host keyword are the same. You can specify the following civic location options in civic location configuration mode:

  • additional-code—Sets an additional civic location code.
  • additional-location-information—Sets additional civic location information.
  • branch-road-name—Sets the branch road name.
  • building—Sets building information.
  • city—Sets the city name.
  • country—Sets the two-letter ISO 3166 country code.
  • county—Sets the county name.
  • default—Sets a command to its defaults.
  • division—Sets the city division name.
  • exit—Exits from the civic location configuration mode.
  • floor—Sets the floor number.
  • landmark—Sets landmark information.
  • leading-street-dir—Sets the leading street direction.
  • name—Sets the resident name.
  • neighborhood—Sets neighborhood information.
  • no—Negates the specified civic location data and sets the default value.
  • number—Sets the street number.
  • post-office-box—Sets the post office box.
  • postal-code—Sets the postal code.
  • postal-community-name—Sets the postal community name.
  • primary-road-name—Sets the primary road name.
  • road-section—Sets the road section.
  • room—Sets room information.
  • seat—Sets seat information.
  • state—Sets the state name.
  • street-group—Sets the street group.
  • street-name-postmodifier—Sets the street name postmodifier.
  • street-name-premodifier—Sets the street name premodifier.
  • street-number-suffix—Sets the street number suffix.
  • street-suffix—Sets the street suffix.
  • sub-branch-road-name—Sets the sub-branch road name.
  • trailing-street-suffix—Sets the trailing street suffix.
  • type-of-place—Sets the type of place.
  • unit—Sets the unit.

You can specify the following geo-spatial location information in geo-location configuration mode:

  • altitude—Sets altitude information in units of floor, meters, or feet.
  • latitude—Sets latitude information in degrees, minutes, and seconds. The range is from -90 degrees to 90 degrees. Positive numbers indicate locations north of the equator.
  • longitude—Sets longitude information in degrees, minutes, and seconds. The range is from -180 degrees to 180 degrees. Positive numbers indicate locations east of the prime meridian.
  • resolution—Sets the resolution for latitude and longitude. If the resolution value is not specified, default value of 10 meters is applied to latitude and longitude resolution parameters. For latitude and longitude, the resolution unit is measured in meters. The resolution value can also be a fraction.
  • default—Sets the geographical location to its default attribute.
  • exit—Exits from geographical location configuration mode.
  • no—Negates the specified geographical parameters and sets the default value.

Use the no lldp med-tlv-select location information interface configuration command to disable the location TLV. The location TLV is enabled by default.

Examples

This example shows how to configure civic location information on the controller:


         
         Controller(config)# location civic-location identifier 1
Controller(config-civic)# number 3550
Controller(config-civic)# primary-road-name “Cisco Way”
Controller(config-civic)# city “San Jose”
Controller(config-civic)# state CA
Controller(config-civic)# building 19
Controller(config-civic)# room C6
Controller(config-civic)# county “Santa Clara”
Controller(config-civic)# country US
Controller(config-civic)# end

You can verify your settings by entering the show location civic-location privileged EXEC command.

This example shows how to configure the emergency location information on the controller:


         
         Controller(config)# location elin-location 14085553881 identifier 1

You can verify your settings by entering the show location elin privileged EXEC command.

The following example shows how to configure geo-spatial location information on the controller:

Controller(config)# location geo-location identifier host
Controller(config-geo)# latitude 12.34
Controller(config-geo)# longitude 37.23
Controller(config-geo)# altitude 5 floor
Controller(config-geo)# resolution 12.34

You can use the show location geo-location identifier command to display the configured geo-spatial location details.

logging event power-inline-status

To enable the logging of Power over Ethernet (PoE) events, use the logging event power-inline-status command in interface configuration mode. To disable the logging of PoE status events, use the no form of this command.

logging event power-inline-status

no logging event power-inline-status

Syntax Description

This command has no arguments or keywords.

Command Default

Logging of PoE events is enabled.

Command Modes

Interface configuration

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

The no form of this command does not disable PoE error events.

Examples

This example shows how to enable logging of PoE events on a port:

Controller(config-if)# interface gigabitethernet1/0/1
Controller(config-if)# logging event power-inline-status 
Controller(config-if)#

show CAPWAP summary

To display all the CAPWAP tunnels established by the controller to access points and other mobility controllers use the show CAPWAP summary command.

show CAPWAP summary

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display CAPWAP tunnels established by the controllers to the access points and other controllers.

Controller# show capwap summary
CAPWAP Tunnels General Statistics:
Number of Capwap Data Tunnels = 8 
Number of Capwap Mobility Tunnels = 0 
Number of Capwap Multicast Tunnels = 0 
Name APName Type PhyPortIf Mode McastIf
------ -------------------------------- ---- --------- ---------
-------
Ca4 AP-Behind-Router data - unicast - 
Ca0 AP1142-kat data - unicast - 
Ca5 APRFCHAMBER2-EDISON data - unicast - 
Ca6 KATANA_2_RF data - unicast - 
Ca1 AP-1040-RF data - unicast - 
Ca7 KATANA_1_RF data - unicast - 
Ca2 AP3500-2027 data - unicast - 
Ca3 AP-1040-out data - unicast -

show env

To display fan, temperature, and power information, use the show env command in EXEC mode.

show env { all | fan | power [ all | switch [ stack-member-number ] ] | stack [ stack-member-number ] | temperature [ status ] }

Syntax Description

all

Displays the fan and temperature environmental status and the status of the internal power supplies.

fan

Displays the switch fan status.

power

Displays the internal power status of the active switch.

all

(Optional) Displays the status of all the internal power supplies in a standalone switch when the command is entered on the switch, or in all the stack members when the command is entered on the .

switch

(Optional) Displays the status of the internal power supplies for each switch in the stack or for the specified switch.

This keyword is available only on stacking-capable switches.

stack-member-number

(Optional) Number of the stack member for which to display the status of the internal power supplies or the environmental status.

The range is 1 to 9.

stack

Displays all environmental status for each switch in the stack or for the specified switch.

This keyword is available only on stacking-capable switches.

temperature

Displays the switch temperature status.

status

(Optional) Displays the switch internal temperature (not the external temperature) and the threshold values.

Command Default

None

Command Modes

User EXEC

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Use the show env EXEC command to display the information for the switch being accessed—a standalone switch or the . Use this command with the stack and switch keywords to display all information for the stack or for the specified stack member.

If you enter the show env temperature status command, the command output shows the switch temperature state and the threshold level.

You can also use the show env temperature command to display the switch temperature status. The command output shows the green and yellow states as OK and the red state as FAULTY. If you enter the show env all command, the command output is the same as the show env temperature status command output.

Examples

This is an example of output from the show env all command:

This is an example of output from the show env fan command:

Controller>show env fan
Switch 1 FAN 1 is OK
Switch 1 FAN 2 is OK
Switch 1 FAN 3 is OK
FAN PS-1 is NOT PRESENT
FAN PS-2 is OK

This is an example of output from the show env power all command on the :

This is an example of output from the show env stack command on the :

Controller> show env stack
SWITCH: 1
Switch 1 FAN 1 is OK
Switch 1 FAN 2 is OK
Switch 1 FAN 3 is OK
FAN PS-1 is NOT PRESENT
FAN PS-2 is OK
Switch 1: SYSTEM TEMPERATURE is OK
Temperature Value: 28 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 41 Degree Celsius
Red Threshold    : 56 Degree Celsius

This example shows how to display the temperature value, state, and the threshold values on a standalone switch. The table describes the temperature states in the command output.

Controller> show env temperature status
Temperature Value: 33 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 65 Degree Celsius
Red Threshold    : 75 Degree Celsius

Table 1 States in the show env temperature status Command Output

State

Description

Green

The switch temperature is in the normal operating range.

Yellow

The temperature is in the warning range. You should check the external temperature around the switch.

Red

The temperature is in the critical range. The switch might not run properly if the temperature is in this range.

show errdisable detect

To display error-disabled detection status, use the show errdisable detect command in EXEC mode.

show errdisable detect

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

User EXEC

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

A gbic-invalid error reason refers to an invalid small form-factor pluggable (SFP) module.

The error-disable reasons in the command output are listed in alphabetical order. The mode column shows how error-disable is configured for each feature.

You can configure error-disabled detection in these modes:

  • port mode—The entire physical port is error-disabled if a violation occurs.
  • vlan mode—The VLAN is error-disabled if a violation occurs.
  • port/vlan mode—The entire physical port is error-disabled on some ports and is per-VLAN error-disabled on other ports.

Examples

This is an example of output from the show errdisable detect command:

show errdisable recovery

To display the error-disabled recovery timer information, use the show errdisable recovery command in EXEC mode.

show errdisable recovery

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

User EXEC

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

A gbic-invalid error-disable reason refers to an invalid small form-factor pluggable (SFP) module interface.


Note


Though visible in the output, the unicast-flood field is not valid.


Examples

This is an example of output from the show errdisable recovery command:

show interfaces

To display the administrative and operational status of all interfaces or for a specified interface, use the show interfaces command in privileged EXEC mode.

show interfaces [ interface-id | vlan vlan-id ] [ accounting | capabilities [ module number ] | debounce | description | etherchannel | flowcontrol | private-vlan mapping | pruning | stats | status [ err-disabled | inactive ] | trunk ]

Syntax Description

interface-id

(Optional) ID of the interface. Valid interfaces include physical ports (including type, stack member for stacking-capable switches, module, and port number) and port channels. The port channel range is 1 to 48.

vlan vlan-id

(Optional) VLAN identification. The range is 1 to 4094.

accounting

(Optional) Displays accounting information on the interface, including active protocols and input and output packets and octets.

Note   

The display shows only packets processed in software; hardware-switched packets do not appear.

capabilities

(Optional) Displays the capabilities of all interfaces or the specified interface, including the features and options that you can configure on the interface. Though visible in the command line help, this option is not available for VLAN IDs.

module number

(Optional) Displays capabilities of all interfaces on the switch or specified stack member.

The range is 1 to 9.

This option is not available if you entered a specific interface ID.

description

(Optional) Displays the administrative status and description set for an interface.

etherchannel

(Optional) Displays interface EtherChannel information.

flowcontrol

(Optional) Displays interface flow control information.

private-vlan mapping

(Optional) Displays private-VLAN mapping information for the VLAN switch virtual interfaces (SVIs). This keyword is not available if the switch is running the LAN base feature set.

pruning

(Optional) Displays trunk VTP pruning information for the interface.

stats

(Optional) Displays the input and output packets by switching the path for the interface.

status

(Optional) Displays the status of the interface. A status of unsupported in the Type field means that a non-Cisco small form-factor pluggable (SFP) module is inserted in the module slot.

err-disabled

(Optional) Displays interfaces in an error-disabled state.

inactive

(Optional) Displays interfaces in an inactive state.

trunk

(Optional) Displays interface trunk information. If you do not specify an interface, only information for active trunking ports appears.


Note


Though visible in the command-line help strings, the crb, fair-queue, irb, mac-accounting, precedence, random-detect, rate-limit, and shape keywords are not supported.


Command Default

None

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

The show interfaces capabilities command with different keywords has these results:
  • Use the show interface capabilities module number command to display the capabilities of all interfaces on that switch in the stack. If there is no switch with that module number in the stack, there is no output.
  • Use the show interfaces interface-id capabilities to display the capabilities of the specified interface.
  • Use the show interfaces capabilities (with no module number or interface ID) to display the capabilities of all interfaces in the stack.

Examples

This is an example of output from the show interfaces command for an interface on stack member 3:

Controller# show interfaces gigabitethernet3/0/2
GigabitEthernet3/0/2 is down, line protocol is down (notconnect)
  Hardware is Gigabit Ethernet, address is 2037.064d.4381 (bia 2037.064d.4381)
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Auto-duplex, Auto-speed, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

This is an example of output from the show interfaces accounting command:

Controller# show interfaces accounting
Vlan1
                Protocol    Pkts In   Chars In   Pkts Out  Chars Out
                      IP          0          0          6        378
Vlan200
                Protocol    Pkts In   Chars In   Pkts Out  Chars Out
No traffic sent or received on this interface.
GigabitEthernet0/0
                Protocol    Pkts In   Chars In   Pkts Out  Chars Out
                   Other     165476   11417844          0          0
           Spanning Tree    1240284   64494768          0          0
                     ARP       7096     425760          0          0
                     CDP      41368   18781072      82908   35318808
GigabitEthernet1/0/1
                Protocol    Pkts In   Chars In   Pkts Out  Chars Out
No traffic sent or received on this interface.
GigabitEthernet1/0/2
                Protocol    Pkts In   Chars In   Pkts Out  Chars Out
No traffic sent or received on this interface.

<output truncated>

This is an example of output from the show interfaces capabilities command for an interface:

Controller# show interfaces gigabitethernet1/0/2 capabilities
GigabitEthernet1/0/2
  Model:                 UA-3850-24-CR
  Type:                  10/100/1000BaseTX
  Speed:                 10,100,1000,auto
  Duplex:                full,half,auto
  Trunk encap. type:     802.1Q
  Trunk mode:            on,off,desirable,nonegotiate
  Channel:               yes
  Fast Start:            yes
  QoS scheduling:        rx-(not configurable on per port basis),
                         tx-(4q3t) (3t: Two configurable values and one fixed.)
  CoS rewrite:           yes
  ToS rewrite:           yes
  UDLD:                  yes
  Inline power:          no
  SPAN:                  source/destination
  PortSecure:            yes
  Dot1x:                 yes

This is an example of output from the show interfaces interface description command when the interface has been described as Connects to Marketing by using the description interface configuration command:

Controller# show interfaces gigabitethernet1/0/2 description
Interface                      Status         Protocol Description
Gi1/0/2                        up             down     Connects to Marketing

This is an example of output from the show interfaces etherchannel command when port channels are configured on the switch:

Controller# show interfaces etherchannel
----
Port-channel34:
Age of the Port-channel   = 28d:18h:51m:46s
Logical slot/port   = 12/34          Number of ports = 0
GC                  = 0x00000000      HotStandBy port = null
Passive port list   =
Port state          = Port-channel L3-Ag Ag-Not-Inuse
Protocol            =    -
Port security       = Disabled

This is an example of output from the show interfaces interface-id pruning command when pruning is enabled in the VTP domain:

Controller# show interfaces gigabitethernet1/0/2 pruning
Port 				 Vlans pruned for lack of request by neighbor
Gi1/0/2   3,4

Port 			  Vlans traffic requested of neighbor
Gi1/0/2   1-3

This is an example of output from the show interfaces stats command for a specified VLAN interface:

Controller# show interfaces vlan 1 stats
Switching path    Pkts In    Chars In    Pkts Out    Chars Out
     Processor    1165354   136205310      570800     91731594
   Route cache          0           0           0            0
         Total    1165354   136205310      570800     91731594

This is an example of partial output from the show interfaces status command. It displays the status of all interfaces:

Controller# show interfaces status
Port      Name               Status       Vlan       Duplex  Speed       Type
Gi1/0/1                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/2                      notconnect   1            auto    100 10/100/1000Ba
seTX
Gi1/0/3                      notconnect   1            auto   1000 10/100/1000Ba
seTX
Gi1/0/4                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/5                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/6                      notconnect   1            auto     10 10/100/1000Ba
seTX
Gi1/0/7                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/8                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/9                      notconnect   1            auto   auto 10/100/1000Ba
seTX
Gi1/0/10                     notconnect   1            auto   auto 10/100/1000Ba
seTX

These are examples of output from the show interfaces status command for a specific interface when private VLANs are configured. Port 22 is configured as a private-VLAN host port. It is associated with primary VLAN 20 and secondary VLAN 25:

Controller# show interfaces gigabitethernet1/0/22 status
Port 						Name 					Status 					Vlan 					Duplex 					Speed					 Type
Gi1/0/22 												connected 		20,25 				a-full 					a-100 					10/100BaseTX

In this example, port 20 is configured as a private-VLAN promiscuous port. The display shows only the primary VLAN 20:

Controller# show interfaces gigabitethernet1/0/20 status
Port 						Name 					Status 					Vlan 					Duplex 					Speed					 Type
Gi1/0/20 												connected 		20    				a-full 					a-100 					10/100BaseTX

This is an example of output from the show interfaces status err-disabled command. It displays the status of interfaces in the error-disabled state:

Controller# show interfaces status err-disabled
Port 		   Name       Status         Reason
Gi1/0/2              err-disabled   gbic-invalid
Gi2/0/3              err-disabled   dtp-flap

This is an example of output from the show interfaces interface-id pruning command:

Controller# show interfaces gigabitethernet1/0/2 pruning
Port Vlans pruned for lack of request by neighbor

This is an example of output from the show interfaces interface-id trunk command. It displays trunking information for the port.

Controller# show interfaces gigabitethernet1/0/1 trunk
Port        Mode             Encapsulation  Status        Native vlan
Gi1/0/1     on               802.1q         other         10

Port        Vlans allowed on trunk
Gi1/0/1     none

Port        Vlans allowed and active in management domain
Gi1/0/1     none

Port        Vlans in spanning tree forwarding state and not pruned
Gi1/0/1     none

show interfaces counters

To display various counters for the switch or for a specific interface, use the show interfaces counters command in privileged EXEC mode.

show interfaces [ interface-id ] counters [ errors | etherchannel | module stack-member-number | protocol status | trunk ]

Syntax Description

interface-id

(Optional) ID of the physical interface, including type, stack member (stacking-capable switches only) module, and port number.

errors

(Optional) Displays error counters.

etherchannel

(Optional) Displays EtherChannel counters, including octets, broadcast packets, multicast packets, and unicast packets received and sent.

module stack-member-number

(Optional) Displays counters for the specified stack member.

The range is 1 to 9.

Note   

In this command, the module keyword refers to the stack member number. The module number that is part of the interface ID is always zero.

protocol status

(Optional) Displays the status of protocols enabled on interfaces.

trunk

(Optional) Displays trunk counters.


Note


Though visible in the command-line help string, the vlan vlan-id keyword is not supported.


Command Default

None

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

If you do not enter any keywords, all counters for all interfaces are included.

Examples

This is an example of partial output from the show interfaces counters command. It displays all counters for the switch.

Controller# show interfaces counters
Port            InOctets    InUcastPkts    InMcastPkts    InBcastPkts
Gi1/0/1                0              0              0              0
Gi1/0/2                0              0              0              0
Gi1/0/3         95285341          43115        1178430           1950
Gi1/0/4                0              0              0              0

<output truncated>

This is an example of partial output from the show interfaces counters module command for stack member 2. It displays all counters for the specified switch in the stack.

Controller# show interfaces counters module 2
Port            InOctets    InUcastPkts    InMcastPkts    InBcastPkts
Gi1/0/1              520              2              0              0
Gi1/0/2              520              2              0              0
Gi1/0/3              520              2              0              0
Gi1/0/4              520              2              0              0

<output truncated>

This is an example of partial output from the show interfaces counters protocol status command for all interfaces:

Controller# show interfaces counters protocol status
Protocols allocated:
Vlan1: Other, IP
Vlan20: Other, IP, ARP
Vlan30: Other, IP, ARP
Vlan40: Other, IP, ARP
Vlan50: Other, IP, ARP
Vlan60: Other, IP, ARP
Vlan70: Other, IP, ARP
Vlan80: Other, IP, ARP
Vlan90: Other, IP, ARP
Vlan900: Other, IP, ARP
Vlan3000: Other, IP
Vlan3500: Other, IP
GigabitEthernet1/0/1: Other, IP, ARP, CDP
GigabitEthernet1/0/2: Other, IP
GigabitEthernet1/0/3: Other, IP
GigabitEthernet1/0/4: Other, IP
GigabitEthernet1/0/5: Other, IP
GigabitEthernet1/0/6: Other, IP
GigabitEthernet1/0/7: Other, IP
GigabitEthernet1/0/8: Other, IP
GigabitEthernet1/0/9: Other, IP
GigabitEthernet1/0/10: Other, IP, CDP

<output truncated>

This is an example of output from the show interfaces counters trunk command. It displays trunk counters for all interfaces.

Controller# show interfaces counters trunk
Port        TrunkFramesTx   TrunkFramesRx   WrongEncap
Gi1/0/1                 0               0            0
Gi1/0/2                 0               0            0
Gi1/0/3             80678               0            0
Gi1/0/4             82320               0            0
Gi1/0/5                 0               0            0

<output truncated>

show location

To display location information for an endpoint, use the show location command in EXEC mode.

show location admin-tag

show location civic-location identifier string interface interface-id static

show location elin-location identifier string interface interface-id static

Syntax Description

admin-tag

Displays administrative tag or site information.

civic-location

Displays civic location information.

elin-location

Displays emergency location information (ELIN).

identifier string

Specifies the ID for the civic location or the ELIN location. The range is 1 to 4095.

interface interface-id

Displays location information for the specified interface or all interfaces. Valid interfaces include physical ports.

static

Displays static configuration information.

Command Modes

User EXEC

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This is an example of output from the show location civic-location command that displays location information for an interface:


         
         Controller# show location civic-location interface gigabitethernet2/0/1
Civic location information
--------------------------
Identifier              : 1
County                  : Santa Clara
Street number           : 3550
Building                : 19
Room                    : C6
Primary road name       : Cisco Way
City                    : San Jose
State                   : CA
Country                 : US

This is an example of output from the show location civic-location command that displays all the civic location information:


         
         Controller# show location civic-location static
Civic location information
--------------------------
Identifier              : 1
County                  : Santa Clara
Street number           : 3550
Building                : 19
Room                    : C6
Primary road name       : Cisco Way
City                    : San Jose
State                   : CA
Country                 : US
Ports                   : Gi2/0/1
--------------------------
Identifier              : 2
Street number           : 24568
Street number suffix    : West
Landmark                : Golden Gate Bridge
Primary road name       : 19th Ave
City                    : San Francisco
Country                 : US
--------------------------

This is an example of output from the show location elin-location command that displays the emergency location information:


         
         Controller# show location elin-location identifier 1
Elin location information
--------------------------
Identifier : 1
Elin       : 14085553881
Ports      : Gi2/0/2

This is an example of output from the show location elin-location static command that displays all emergency location information:


         
         Controller# show location elin-location static 
Elin location information
--------------------------
Identifier : 1
Elin       : 14085553881
Ports      : Gi2/0/2
--------------------------
Identifier : 2
Elin       : 18002228999
--------------------------

show mgmt-infra trace messages ilpower-ha

To display inline power high availability messages within a trace buffer, use the show mgmt-infra trace messages ilpower-ha command in privileged EXEC mode.

show mgmt-infra trace messages ilpower-ha [ switch stack-member-number ]

Syntax Description

switch stack-member-number

(Optional) Specifies the stack member number for which to display inline power messages within a trace buffer.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This is an output example from the show mgmt-infra trace messages ilpower-ha command:

Controller# show mgmt-infra trace messages ilpower-ha
[10/23/12 14:04:48.087 UTC 1 3] NG3K_ILPOWER_HA: Created NGWC ILP CF client succ
essfully.

show network-policy profile

To display the network-policy profiles, use the show network policy profile command in privileged EXEC mode.

show network-policy profile [ profile-number ] [ detail ]

Syntax Description

profile-number

(Optional) Displays the network-policy profile number. If no profile is entered, all network-policy profiles appear.

detail

(Optional) Displays detailed status and statistics information.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This is an example of output from the show network-policy profile command:

Controller# show network-policy profile
Network Policy Profile 10
   voice vlan 17 cos 4
  Interface:
   none
Network Policy Profile 30
   voice vlan 30 cos 5
  Interface:
   none
Network Policy Profile 36
   voice vlan 4 cos 3
  Interface:
   Interface_id

show nmsp

To display the Network Mobility Services Protocol (NMSP) information for the switch, use the
 show nmsp command in privileged EXEC mode.

show nmsp { attachment suppress interface | capability | notification interval | statistics { connection | summary } | status | subscription { detail | summary } }

Syntax Description

attachment suppress interface

Displays attachment suppress interfaces.

capability

Displays switch capabilities including the supported services and subservices.

notification interval

Displays the notification intervals of the supported services.

statistics

Displays the NMSP statistics information.

connection

Displays the message counters on each connection.

summary

Displays the global counters.

status

Displays information about the NMSP connections.

subscription

Displays the subscription information on each NMSP connection.

detail

Displays all services and subservices subscribed on each connection.

summary

Displays all services subscribed on each connection.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This is an example of output from the show nmsp attachment suppress interface command:

Controller# show nmsp attachment suppress interface
NMSP Attachment Suppression Interfaces
--------------------------------------
GigabitEthernet1/0/1
GigabitEthernet1/0/3

This is an example of output from the show nmsp capability command:

Controller# show nmsp capability
Service         Subservice
--------------------------
RSSI            Mobile Station, Tags, Rogue
Info            Mobile Station, Rogue
Statistics      Mobile Station, Tags
Attachment      Wired Station
Location        Subscription
AP Monitor      Subscription
IDS Services    WIPS

This is an example of output from the show nmsp notification interval command:

Controller# show nmsp notification interval
NMSP Notification Intervals
---------------------------

RSSI Interval:
  Client              : 2 sec
  RFID                : 2 sec
  Rogue AP            : 2 sec
  Rogue Client        : 2 sec
Attachment Interval   : 30 sec
Location Interval     : 30 sec

This is an example of output from the show nmsp statistics summary command:

Controller# show nmsp statistics summary
NMSP Global Counters
--------------------

Client measure send fail                   : 0
Send RSSI with no entry                    : 0
Application message too big                : 0
Failed select on accept socket             : 0
Failed SSL write                           : 0
Partial SSL write                          : 0
SSL write returned zero                    : 0
SSL write attempts to want read            : 0
SSL write attempts to want write           : 0
SSL write got default error                : 0
SSL write max data length sent             : 0
SSL write max attempts to write in loop    : 0
SSL read returned zero                     : 0
SSL read attempts to want read             : 0
SSL read attempts to want write            : 0
SSL read got default error                 : 0
Failed SSL read - con rx buf freed         : 0
Failed SSL read - con/SSL freed            : 0
Max records read before exiting SSL read   : 0
Highest priority tx queue full             : 0
Normal priority tx queue full              : 0
Highest priority tx queue count            : 0
Normal priority tx queue count             : 0
APP sent message to highest priority queue : 0
Max measure notify message                 : 0
Max info notify message                    : 0
Max highest priority tx queue count        : 0
Max normal priority tx queue count         : 0
Max receive queue count                    : 3
Max info notify queue count                : 0
Max client info notify delay               : 0
Max rogue AP info notify delay             : 0
Max rogue client info notify delay         : 0
Max client measure notify delay            : 0
Max tag measure notify delay               : 0
Max rogue AP measure notify delay          : 0
Max rogue client measure notify delay      : 0
Max client stats notify delay              : 0
Max RFID stats notify delay                : 0
RFID measurement periodic                  : 0
RFID measurement immediate                 : 0
SSL handshake failed                       : 0
NMSP rx detected connection failure        : 0
NMSP tx detected connection failure        : 0
NMSP tx buf size exceeded                  : 0
Reconnect before connection Timeout        : 0

show platform CAPWAP summary

To display the tunnel identifier and the type all the CAPWAP tunnels established by the controller to the access points and other mobility controllers, use the show platform CAPWAP summary command.

show platform CAPWAP summary

Syntax Description

This command has no arguments or keywords.

Command Default

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example displays the tunnel identifier and details:

Controller# show platform capwap summary
Tunnel ID | Type | Src IP | Dst IP | SPrt | DPrt | S | A 
-------------------------------------------------------------------------------

0x0088498000000983 data 9.6.44.61 9.12.138.101 5247 41894 1 1

0x00966dc000000010 data 9.6.44.61 9.6.47.101 5247 62526 1 2 
0x00938e800000095b data 9.6.44.61 9.12.138.100 5247 45697 1 1

0x00ab1a8000000bd1 data 9.6.44.61 9.12.139.101 5247 38906 1 0

0x00896e40000000bd data 9.6.44.61 9.12.136.100 5247 1836 1 1

show network-policy profile

To display the network-policy profiles, use the show network policy profile command in privileged EXEC mode.

show network-policy profile [ profile-number ] [ detail ]

Syntax Description

profile-number

(Optional) Displays the network-policy profile number. If no profile is entered, all network-policy profiles appear.

detail

(Optional) Displays detailed status and statistics information.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This is an example of output from the show network-policy profile command:

Controller# show network-policy profile
Network Policy Profile 10
   voice vlan 17 cos 4
  Interface:
   none
Network Policy Profile 30
   voice vlan 30 cos 5
  Interface:
   none
Network Policy Profile 36
   voice vlan 4 cos 3
  Interface:
   Interface_id

show wireless interface summary

To display the wireless interface status and configuration, use the show wireless interface summary command.

The command displays the total number of packets that are sent or received by the controllers.

show wireless interface summary

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History

Release Modification
Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display the summary of wireless interfaces.

Controller# show wireless interface summary 
Interface Name Interface Type VLAN ID IP Address IP Netmask MAC Address
--------------------------------------------------------------------------------

Vlan10 Management 10 3.1.1.1 255.255.255.0 0006.f6b9.b5c6
Controller#
                                        
                                             

system mtu

Syntax Description

bytes

Command Default

The default MTU size for all ports is 1500 bytes.

Command Modes

Global configuration

Command History

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You can verify your setting by entering the show system mtu privileged EXEC command.

The switch does not support the MTU on a per-interface basis.

If you enter a value that is outside the allowed range for the specific type of interface, the value is not accepted.

wireless ap-manager interface

To configure the wireless AP-manager interface, use the wireless ap-manager interface command.

wireless ap-managerinterface { TenGigabitEthernet interface-number | Vlan interface-number }

Syntax Description

TenGigabitEthernet interface-name

Configures 10-Gigabit Ethernet interface. Values range from 0 to 9.

Vlan interface-name

Configures VLANs. Values range from 1 to 4095.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure the wireless AP-manager:

Controller# wireless ap-manager interface vlan
<1-4095>  Vlan interface number

This example shows how to configure the wireless AP-manager:

Controller# #wireless ap-manager interface vlan 10

wireless exclusionlist

To manage exclusion list entries, use the wireless exclusionlist global configuration command. To remove the exclusion list entries, use the no form of the command.

wireless exclusionlist mac-addr description description

no wireless exclusionlist mac-addr

Syntax Description

mac-addr

The MAC address of the local excluded entry.

description description

Specifies the description for an exclusion-list entry.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to create a local exclusion list entry for the MAC address xxx.xxx.xxx:

Controller# wireless exclusionlist xxx.xxx.xxx

This example shows how to create a description for the local exclusion list entry for the MAC address xxx.xxx.xxx:

Controller# wireless exclusionlist xxx.xxx.xxx description sample

wireless linktest

To configure linktest frame size and number of frames to send, use the wireless linktest command.

wireless linktest { frame-size size | number-of-frames value }

Syntax Description

frame-size size

Specifies the link test frame size for each packet. The values range from 1 to 1400.

number-of-frames value

Specifies the number of frames to be sent for the link test. The values range from 1 to 100.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure the link test frame size of each frame as 10:

Controller# wireless linktest frame-size 10

wireless management interface

To configure wireless management parameters on an interface, use the wireless management interface global configuration command. To remove a wireless management parameters on an interface, use the no form of the command.

wireless management interface interface-name { TenGigabitEthernet interface-name | Vlan interface-name }

no wireless management interface

Syntax Description

interface-name

The interface number.

TenGigabitEthernet interface-name

The 10-Gigabit Ethernet interface number. The values range from 0 to 9.

Vlan interface-name

The VLAN interface number. The values range from 1 to 4095.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure VLAN 10 on the wireless interface:

Controller# wireless management interface Vlan 10

wireless peer-blocking forward-upstream

To configure peer-to-peer blocking for forward upstream, use the wireless peer-blocking forward-upstream command. To remove a peer-to-peer blocking, use the no form of the command.

wireless peer-blocking forward-upstream interface { GigabitEthernet interface-number TenGigabitEthernet interface-number }

no wireless peer-blocking forward-upstream { GigabitEthernet interface-number TenGigabitEthernet interface-number }

Syntax Description

GigabitEthernet interface

The Gigabit Ethernet interface number. Values range from 0 to 9.

TenGigabitEthernet interface

The 10-Gigabit Ethernet interface number. Values range from 0 to 9.

Command Default

None

Command Modes

Global configuration

Command History

Release Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to configure peer-to-peer blocking for interface 10-gigabit ethernet interface:

Controller(config)# wireless peer-blocking forward-upstream TenGigabitEthernet 1/1/4