Consolidated Platform Command Reference, Cisco IOS XE Release 3.3SE (Cisco WLC 5700 Series)
CleanAir Commands
Downloads: This chapterpdf (PDF - 1.48MB) The complete bookPDF (PDF - 8.86MB) | The complete bookePub (ePub - 1.41MB) | Feedback

CleanAir Commands

Contents

CleanAir Commands

ap dot11 5ghz cleanair

To enable CleanAir for detecting 5-GHz devices, use the ap dot11 5ghz cleanair command in global configuration mode.

ap dot11 5ghz cleanair

Command Default

Disabled.

Command Modes

Global configuration.

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable this CleanAir command before you configure other CleanAir commands.

Examples

This example shows how to enable CleanAir for 5-GHz devices:

Controller(config)# ap dot11 5ghz cleanair

ap dot11 5ghz cleanair alarm air-quality

To configure the alarm when the Air Quality (AQ) reaches the threshold value for the 5-GHz devices, use the ap dot11 5ghz cleanair alarm air-quality command. To disable the alarm when the AQ reaches the threshold value for the 5-GHz devices, use the no form of this command.

ap dot11 5ghz cleanair alarm air-quality threshold threshold _value

Syntax Description

threshold threshold _value

Configures the threshold value for air quality. The range is from 1 to 100.

Command Default

The default threshold value for AQ is 10.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 5ghz cleanaircommand before you configure this command.

Examples

This example shows how to set the threshold value for the AQ:

Controller(config)# ap dot11 5ghz cleanair alarm air-quality threshold 30

ap dot11 5ghz cleanair alarm device

To configure the alarm for the 5-GHz interference devices, use the ap dot11 5ghz cleanair alarm device command.

ap dot11 5ghz cleanair alarm device {canopy | cont-tx | dect-like | inv | jammer | nonstd | radar | superag | tdd-tx | video | wimax-fixed | wimax-mobile}

Syntax Description

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

radar

Configures the alarm for radars.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled and for all other interference devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 5ghz cleanair command before you configure this command.

Examples

This example shows how to enable the alarm to notify interferences from a radar device:

Controller(config)# ap dot11 5ghz cleanair alarm device radar

default ap dot11 5ghz cleanair device

To configure the default state of the alarm for 5-GHz interference devices, use the default ap dot11 5ghz cleanair device command in global configuration mode.

default ap dot11 5ghz cleanair device { canopy | cont-tx | dect-like | inv | jammer | nonstd | radar | report | superag | tdd-tx | video | wimax-fixed | wimax-mobile }

Syntax Description

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

radar

Configures the alarm for radars.

report

Enables interference device reports.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all other interference devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 5ghz cleanair command before you configure this command.

Examples

This example shows how to enable CleanAir to report when a video camera interferes:

Controller(config)# default ap dot11 5ghz cleanair device video

ap dot11 5ghz rrm channel cleanair-event

To enable Event-Driven RRM (EDRRM) and configure the sensitivity for 5-GHz devices, use the ap dot11 5ghz rrm channel cleanair-event command in global configuration mode. To disable EDRRM, use the no form of the command.

ap dot11 5ghz rrm channel cleanair-event [ sensitivity { high | low | medium } ]

no ap dot11 5ghz rrm channel cleanair-event [ sensitivity { high | low | medium } ]

Syntax Description

sensitivity

(Optional) Configures the EDRRM sensitivity of the CleanAir event.

high

(Optional) Specifies the highest sensitivity to non-Wi–Fi interference as indicated by the air quality (AQ) value.

low

(Optional) Specifies the least sensitivity to non-Wi–Fi interference as indicated by the AQ value.

medium

(Optional) Specifies medium sensitivity to non-Wi–Fi interference as indicated by the AQ value.

Command Default

EDRRM is disabled and the EDRRM sensitivity is low.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable EDRRM using the ap dot11 5ghz rrm channel cleanair-event command before you configure the sensitivity.

Examples

This example shows how to enable EDRRM and set the EDRRM sensitivity to high:

Controller(config)# ap dot11 5ghz rrm channel cleanair-event 
Controller(config)# ap dot11 5ghz rrm channel cleanair-event sensitivity high

ap dot11 5ghz rrm channel device

To configure persistent non-Wi-Fi device avoidance in the 802.11a channel, use the ap dot11 5ghz rrm channel device command in global configuration mode. To disable persistent device avoidance, use the no form of this command.

ap dot11 5ghz rrm channel device

no ap dot11 5ghz rrm channel device

Syntax Description

This command has no arguments or keywords.

Command Default

The CleanAir persistent device state is disabled.

Command Modes

Global configuration (config)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

CleanAir-capable monitor mode access points collect information about persistent devices on all configured channels and stores the information in the controller. Local and bridge mode access points detect interference devices on the serving channels only.

Examples

This example shows how to enable persistent device avoidance on 802.11a devices:

Controller(config)# ap dot11 5ghz rrm channel device

ap dot11 24ghz cleanair

To enable CleanAir for detecting 2.4-GHz devices, use the ap dot11 24ghz cleanair command in global configuration mode. To disable CleanAir for detecting 2.4-GHz devices, use the no form of this command.

ap dot11 24ghz cleanair

Syntax Description

This command has no arguments or keywords.

Command Default

Disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable this CleanAir command before you configure other CleanAir commands.

Examples

This example shows how to enable CleanAir for 2.4-GHz devices:

Controller(config)# ap dot11 24ghz cleanair

ap dot11 24ghz cleanair alarm air-quality

To configure the alarm for the threshold value of Air Quality (AQ) for all 2.4-GHz devices, use the ap dot11 24ghz cleanair alarm air-quality command in global configuration mode. To disable the alarm for the threshold value of AQ for all 2.4-GHz devices, use the no form of this command.

ap dot11 24ghz cleanair alarm air-quality threshold threshold_value

Syntax Description

threshold threshold_value

Configures the threshold value for AQ. The range is from 1 to 100.

Command Default

The default threshold value for AQ is 10.

Command Modes

Global configuration (config)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 24ghz cleanair command before you configure this command.

Examples

This example shows how to set the threshold value for the AQ:

Controller(config)# ap dot11 24ghz cleanair alarm air-quality threshold 50

ap dot11 24ghz cleanair alarm device

To configure the alarm for the 2.4-GHz interference devices, use the ap dot11 24ghz cleanair alarm device command in global configuration mode. To disable the alarm for the 2.4-GHz interference devices, use the no form of this command.

ap dot11 24ghz cleanairalarm { device | bt-discovery | bt-link canopy| cont-tx | dect-like | fh | inv | jammer | mw-oven | nonstd | superag | tdd-tx video | wimax-fixed | wimax-mobile | xbox | zigbee}

Syntax Description

bt-discovery

Configures the alarm for Bluetooth interference devices.

bt-link

Configures the alarm for any Bluetooth link.

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

fh

Configures the alarm for 802.11 frequency hopping (FH) devices.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

mw-oven

Configures the alarm for microwave ovens.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

xbox

Configures the alarm for Xbox interference devices.

zigbee

Configures the alarm for 802.15.4 interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all other devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 24ghz cleanair command before you configure this command.

Examples

This example shows how to enable the alarm to notify interferences from a Zigbee device:

Controller(config)# ap dot11 24ghz cleanair alarm device zigbee

default ap dot11 24ghz cleanair device

To configure the default state of report generation for 2.4-GHz interference devices, use the default ap dot11 24ghz cleanair device command in global configuration mode.

default ap dot11 24ghz cleanair device { bt-discovery | bt-link | canopy | cont-tx | dect-like | fh | inv | jammer | mw-oven | nonstd | report | superag | tdd-tx | video | wimax-fixed | wimax-mobile | xbox | zigbee }

Syntax Description

bt-discovery

Configures the alarm for Bluetooth interference devices.

bt-link

Configures the alarm for any Bluetooth link.

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

fh

Configures the alarm for 802.11 frequency hopping devices.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

mw-oven

Configures the alarm for microwave ovens.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

xbox

Configures the alarm for Xbox interference devices.

zigbee

Configures the alarm for 802.15.4 interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all other devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 24ghz cleanaircommand before you configure this command.

Examples

This example shows how to enable CleanAir to report when a video camera interferes:

Controller(config)# default ap dot11 24ghz cleanair device video

ap dot11 24ghz rrm channel cleanair-event

To enable Event-Driven RRM (EDRRM) and the sensitivity for 2.4-GHz devices, use the ap dot11 24ghz rrm channel cleanair-event command in global configuration mode. To disable EDRRM, use the no form of this command.

ap dot11 24ghz rrm channel cleanair-event sensitivity { high | low | medium }

no ap dot11 24ghz rrm channel cleanair-event [sensitivity{high | low | medium}]

Syntax Description

sensitivity

(Optional) Configures the EDRRM sensitivity of the CleanAir event.

high

(Optional) Specifies the highest sensitivity to non-Wi–Fi interference as indicated by the air quality (AQ) value.

low

(Optional) Specifies the least sensitivity to non-Wi–Fi interference as indicated by the AQ value.

medium

(Optional) Specifies medium sensitivity to non-Wi–Fi interference as indicated by the AQ value.

Command Default

EDRRM is disabled and the sensitivity is low.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable EDRRM using the ap dot11 24ghz rrm channel cleanair-event command before you configure the sensitivity.

Examples

This example shows how to enable EDRRM and set the EDRRM sensitivity to low:

Controller(config)# ap dot11 24ghz rrm channel cleanair-event 
Controller(config)# ap dot11 24ghz rrm channel cleanair-event sensitivity low

ap dot11 24ghz rrm channel device

To configure persistent non-Wi-Fi device avoidance in the 802.11b channel, use the ap dot11 24ghz rrm channel device command in global configuration mode. To disable persistent device avoidance, use the no form of this command.

ap dot11 24ghz rrm channel device

no ap dot11 24ghz rrm channel device

Syntax Description

This command has no arguments or keywords.

Command Default

Persistent device avoidance is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

CleanAir-capable monitor mode access points collect information about persistent devices on all configured channels and stores the information in the controller. Local and bridge mode access points detect interference devices on the serving channels only.

Examples

This example shows how to enable persistent device avoidance:

Controller(config)# ap dot11 24ghz rrm channel device

ap name mode se-connect

To configure the access point for SE-Connect mode, use the ap name ap_name mode se-connect command in privileged exec mode.

ap name ap_name mode se-connect

Syntax Description

ap_name

Name of the access point.

Command Default

No access point is configured for SE-Connect mode.

Command Modes

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

The access point will reboot after you change the mode.

SE-connect mode enables a user to connect a Spectrum Expert application running on an external Microsoft Windows XP or Vista PC to a Cisco CleanAir-enabled access point in order to display and analyze detailed spectrum data. The Spectrum Expert application connects directly to the access point, by passing the controller. An access point in SE-Connect mode does not provide any Wi-Fi, RF, or spectrum data to the controller. All CleanAir system functionality is suspended while the AP is in this mode, and no clients are served. This mode is intended for remote troubleshooting only.

Examples

This example shows how to change the mode of the access point to SE-Connect:

Controller# ap name AS-5508-5-AP3 mode se-connect

Changing the AP's mode will cause the AP to reboot.
Are you sure you want to continue? (y/n)[y]: y
% switch-1:wcm:Cisco AP does not support the seconnect mode

default ap dot11 5ghz cleanair device

To configure the default state of the alarm for 5-GHz interference devices, use the default ap dot11 5ghz cleanair device command in global configuration mode.

default ap dot11 5ghz cleanair device { canopy | cont-tx | dect-like | inv | jammer | nonstd | radar | report | superag | tdd-tx | video | wimax-fixed | wimax-mobile }

Syntax Description

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

radar

Configures the alarm for radars.

report

Enables interference device reports.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all other interference devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 5ghz cleanair command before you configure this command.

Examples

This example shows how to enable CleanAir to report when a video camera interferes:

Controller(config)# default ap dot11 5ghz cleanair device video

default ap dot11 5ghz rrm channel cleanair-event

To configure the default state of Event-Driven radio resource management (EDRRM) and the EDRRM sensitivity for 5-GHz devices, use the default ap dot11 5ghz rrm channel cleanair-event command in global configuration mode.

default ap dot11 5ghz rrm channel cleanair-event [ sensitivity { high | low | medium } ]

Syntax Description

sensitivity

(Optional) Configures the EDRRM sensitivity of the CleanAir event.

high

(Optional) Specifies the highest sensitivity to non-Wi–Fi interference as indicated by the Air Quality (AQ) value.

low

(Optional) Specifies the least sensitivity to non-Wi–Fi interference as indicated by the AQ value.

medium

(Optional) Specifies medium sensitivity to non-Wi–Fi interference as indicated by the AQ value.

Command Default

EDRRM is disabled and the sensitivity is low.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable EDRRM before you configure the sensitivity.

Examples

This example shows how to set the default EDRRM state and sensitivity:

Controller(config)# default ap dot11 5ghz rrm channel cleanair-event 
Controller(config)# default ap dot11 5ghz rrm channel cleanair-event sensitivity 

default ap dot11 5ghz rrm channel device

To configure the default state of the persistent non-Wi-Fi device avoidance in the 802.11a channels, use the default ap dot11 5ghz rrm channel device command in global configuration mode.

default ap dot11 5ghz rrm channel device

Syntax Description

This command has no arguments or keywords.

Command Default

Persistent device state is disabled.

Command Modes

Global configuration (config)

Command History

Release

Modification

Cisco IOS XE 3.3SE

This command was introduced.

Examples

This example shows how to configure persistent non-Wi-Fi device avoidance in the 802.11a channels:

Controller(config)# default ap dot11 5ghz rrm channel device

default ap dot11 24ghz cleanair alarm device

To configure the default value of the alarm for 2.4-GHz interference devices, use the default ap dot11 24ghz cleanair alarm device command in global configuration mode.

default ap dot11 24ghz cleanair alarm device { bt-discovery | bt-link | canopy | cont-tx | dect-like | fh | inv | jammer | mw-oven| nonstd | superag | tdd-tx | video | wimax-fixed | wimax-mobile | xbox | zigbee}

Syntax Description

bt-discovery

Configures the alarm for Bluetooth interference devices.

bt-link

Configures the alarm for any Bluetooth link.

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

fh

Configures the alarm for 802.11 frequency hopping (FH) devices.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

mw-oven

Configures the alarm for microwave ovens.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

xbox

Configures the alarm for Xbox interference devices.

zigbee

Configures the alarm for 802.15.4 interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all the other devices is disabled.

Command Modes

Global configuration (config)

Command History

Release Modification

Cisco IOS XE 3.3SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 24ghz cleanair command before you configure this command.

Examples

This example shows how to configure the default CleanAir 2.4-GHz interference devices alarm:

Controller(config)# default ap dot11 24ghz cleanair alarm device inv

default ap dot11 24ghz cleanair device

To configure the default state of report generation for 2.4-GHz interference devices, use the default ap dot11 24ghz cleanair device command in global configuration mode.

default ap dot11 24ghz cleanair device { bt-discovery | bt-link | canopy | cont-tx | dect-like | fh | inv | jammer | mw-oven | nonstd | report | superag | tdd-tx | video | wimax-fixed | wimax-mobile | xbox | zigbee }

Syntax Description

bt-discovery

Configures the alarm for Bluetooth interference devices.

bt-link

Configures the alarm for any Bluetooth link.

canopy

Configures the alarm for canopy interference devices.

cont-tx

Configures the alarm for continuous transmitters.

dect-like

Configures the alarm for Digital Enhanced Cordless Communication (DECT)-like phones.

fh

Configures the alarm for 802.11 frequency hopping devices.

inv

Configures the alarm for devices using spectrally inverted Wi-Fi signals.

jammer

Configures the alarm for jammer interference devices.

mw-oven

Configures the alarm for microwave ovens.

nonstd

Configures the alarm for devices using nonstandard Wi-Fi channels.

superag

Configures the alarm for 802.11 SuperAG interference devices.

tdd-tx

Configures the alarm for Time Division Duplex (TDD) transmitters.

video

Configures the alarm for video cameras.

wimax-fixed

Configures the alarm for WiMax fixed interference devices.

wimax-mobile

Configures the alarm for WiMax mobile interference devices.

xbox

Configures the alarm for Xbox interference devices.

zigbee

Configures the alarm for 802.15.4 interference devices.

Command Default

The alarm for Wi-Fi inverted devices is enabled. The alarm for all other devices is disabled.

Command Modes

Global configuration (config).

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

You must enable CleanAir using the ap dot11 24ghz cleanaircommand before you configure this command.

Examples

This example shows how to enable CleanAir to report when a video camera interferes:

Controller(config)# default ap dot11 24ghz cleanair device video

default ap dot11 24ghz rrm channel cleanair-event

To configure the default Event-Driven radio resource management (EDRRM) state and sensitivity for 2.4-GHz devices, use the default ap dot11 24ghz rrm channel cleanair-event command in global configuration mode.

default ap dot11 24ghz rrm channel cleanair-event [sensitivity {high | low | medium}]

Syntax Description

sensitivity

Configures the EDRRM sensitivity of the CleanAir event.

high

Specifies the highest sensitivity to non-Wi–Fi interference as indicated by the Air Quality (AQ) value.

low

Specifies the least sensitivity to non-Wi–Fi interference as indicated by the AQ value.

medium

Specifies medium sensitivity to non-Wi–Fi interference as indicated by the AQ value.

Command Default

EDRRM is disabled and the sensitivity is low.

Command Modes

Global configuration (config)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to enable EDRRM and set the default EDRRM sensitivity:

Controller(config)# default ap dot11 24ghz rrm channel cleanair-event
Controller(config)# default ap dot11 24ghz rrm channel cleanair-event sensitivity

show ap dot11 5ghz cleanair air-quality summary

To display the CleanAir AQ data for 5-GHz band, use the show ap dot11 5ghz cleanair air-quality summary command in user EXEC mode or privileged EXEC mode.

show ap dot11 5ghz cleanair air-quality summary

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display the CleanAir AQ data for 5-GHz band:

Controller# show ap dot11 5ghz cleanair air-quality summary
 
AQ = Air Quality
DFS = Dynamic Frequency Selection
 
AP Name             Channel   Avg AQ  Min AQ  Interferers  DFS
--------------------------------------------------------------
AP270ca.9b86.4546   1         99      99      0            No
AP2894.0f26.22df    6         98      97      0            No
AP2894.0f58.cc6b    11        99      99      0            No
AP2894.0f39.1040    6         97      97      0            No
AP2894.0f63.c6da    11        99      99      0            No
AP2894.0f58.d013    6         97      97      0            No
 

show ap dot11 5ghz cleanair air-quality worst

To display the worst AQ data for 5-GHz band, use the show ap dot11 5ghz cleanair air-quality worst command in user EXEC mode or privileged EXEC mode.

show ap dot11 5ghz cleanair air-quality worst

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display the worst AQ data for 5-GHz band:

Controller# show ap dot11 5ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
 
AP Name             Channel   Avg AQ  Min AQ  Interferers  DFS
--------------------------------------------------------------
AP2894.0f39.1040    6         97      97      0            No

show ap dot11 5ghz cleanair config

To display the CleanAir configuration for 5-GHz band, use the show ap dot11 5ghz cleanair config command.

show ap dot11 5ghz cleanair config

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

In Release 3.3SE, you can configure this command on the Mobility Agent (MA).

Examples

This example shows how to display the CleanAir configuration for 5-GHz band on the Mobility Controller:

Controller# show ap dot11 5ghz cleanair config

CleanAir Solution................................ : Enabled
Air Quality Settings:
    Air Quality Reporting........................ : Enabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 1
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Alarms................... : Enabled
Additional CleanAir Settings:
    CleanAir Event-driven RRM State.............. : Enabled
    CleanAir Driven RRM Sensitivity.............. : HIGH
    CleanAir Persistent Devices state............ : Enabled

This example shows how to display the CleanAir configuration for 5-GHz band on the Mobility Agent:

Controller# show ap dot11 5ghz cleanair config

Mobility Controller Link Status.................. : UP
CleanAir Solution................................ : Enabled
Air Quality Settings:
    Air Quality Reporting........................ : Enabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 10
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... : Disabled
        Jammer................................... : Disabled
        Continuous Transmitter................... : Disabled
        DECT-like Phone.......................... : Disabled
        Video Camera............................. : Disabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Disabled
        WiMax Mobile............................. : Disabled
        WiMax Fixed.............................. : Disabled
    Interference Device Alarms................... : Enabled
Additional CleanAir Settings:
    CleanAir Event-driven RRM State.............. : Disabled
    CleanAir Driven RRM Sensitivity.............. : LOW
    CleanAir Persistent Devices state............ : Disabled


show ap dot11 5ghz cleanair device type

To display the 5-GHz interference devices, use the show ap dot11 5ghz cleanair device type command.

show ap dot11 5ghz cleanair device type { all | canopy | cont-tx | dect-like | inv | jammer | nonstd | persistent | superag | tdd-tx | video | wimax-fixed | wimax-mobile }

Syntax Description

all

Displays all CleanAir interferer devices for 5-GHz band.

canopy

Displays CleanAir interferers of type canopy for 5-GHz band.

cont-tx

Displays CleanAir interferers of type continuous transmitter for 5-GHz band.

dect-like

Displays CleanAir interferers of type Digital Enhanced Cordless Communication (DECT)-like phone for 5-GHz band.

inv

Displays CleanAir interferer devices using spectrally inverted WiFi signals for 5-GHz band.

jammer

Displays CleanAir interferers of type jammer for 5-GHz band.

nonstd

Displays CleanAir interferer devices using non-standard Wi-Fi channels for 5-GHz band.

persistent

Displays CleanAir persistent device interferers for 5-GHz band.

superag

Displays CleanAir interferers of type SuperAG for 5-GHz band.

tdd-tx

Displays CleanAir Time Division Duplex (TDD) transmitters for 5-GHz band.

video

Displays CleanAir interferers of type video camera for 5-GHz band.

winmax-fixed

Displays CleanAir interferers of type WiMax fixed for 5-GHz band.

wimax-mobile

Displays CleanAir interferers of type WiMax mobile for 5-GHz band.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

Interference devices are listed only if there is an interference from any 5-GHz devices.

Examples

This example shows how to view all the 5-GHz interference devices:

Controller# show ap dot11 5ghz cleanair device type all

DC    = Duty Cycle (%)
ISI   = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID

No    ClusterID          DevID  Type           AP Name                 ISI  RSSI  DC   Channel
-------------------------------------------------------------------------------------------------
                                                                              

show ap dot11 24ghz cleanair air-quality summary

To display the CleanAir AQ data for 2.4-GHz band, use the show ap dot11 24ghz cleanair air-quality summary command in user EXEC mode or privileged EXEC mode.

show ap dot11 24ghz cleanair air-quality summary

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display the CleanAir AQ data for 2.4-GHz band:

Controller# show ap dot11 24ghz cleanair air-quality summary

AQ = Air Quality
DFS = Dynamic Frequency Selection
 
AP Name             Channel   Avg AQ  Min AQ  Interferers  DFS
--------------------------------------------------------------
AP270ca.9b86.4546   1         99      99      0            No
AP2894.0f26.22df    6         98      97      0            No
AP2894.0f58.cc6b    11        99      99      0            No
AP2894.0f39.1040    6         97      97      0            No
AP2894.0f63.c6da    11        99      99      0            No

show ap dot11 24ghz cleanair air-quality worst

To display the worst air quality data for 2.4-GHz band, use the show ap dot11 24ghz cleanair air-quality worst command in user EXEC mode or privileged EXEC mode.

show ap dot11 24ghz cleanair air-quality worst

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Examples

This example shows how to display the worst AQ data for 2.4-GHz band:

Controller# show ap dot11 24ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
 
AP Name             Channel   Avg AQ  Min AQ  Interferers  DFS
--------------------------------------------------------------
AP2895.0f39.1040    6         97      97      0            No

show ap dot11 24ghz cleanair config

To display the CleanAir configuration for 2.4-GHz band, use the show ap dot11 24ghz cleanair config command in user EXEC mode or privileged EXEC mode.

show ap dot11 24ghz cleanair config

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Usage Guidelines

In Release 3.3SE, you can configure this command on the Mobility Agent (MA).

Examples

This example shows how to display the CleanAir configuration for 2.4-GHz band on the Mobility Controller:

Controller# show ap dot11 24ghz cleanair config

CleanAir Solution................................ : Enabled
Air Quality Settings:
    Air Quality Reporting........................ : Enabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 1
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Alarms................... : Enabled
Additional CleanAir Settings:
    CleanAir Event-driven RRM State.............. : Enabled
    CleanAir Driven RRM Sensitivity.............. : HIGH
    CleanAir Persistent Devices state............ : Enabled

This example shows how to display the CleanAir configuration for 2.4-GHz band on the Mobility Agent:

Controller# show ap dot11 24ghz cleanair config

Mobility Controller Link Status.................. : UP
CleanAir Solution................................ : Enabled
Air Quality Settings:
    Air Quality Reporting........................ : Enabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 10
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... : Disabled
        Jammer................................... : Disabled
        Continuous Transmitter................... : Disabled
        DECT-like Phone.......................... : Disabled
        Video Camera............................. : Disabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Disabled
        WiMax Mobile............................. : Disabled
        WiMax Fixed.............................. : Disabled
    Interference Device Alarms................... : Enabled
Additional CleanAir Settings:
    CleanAir Event-driven RRM State.............. : Disabled
    CleanAir Driven RRM Sensitivity.............. : LOW
    CleanAir Persistent Devices state............ : Disabled


show ap dot11 24ghz cleanair summary

To display a summary of 2.4-GHz CleanAir devices, use the show ap dot11 24ghz cleanair summary command in user EXEC mode or privileged EXEC mode.

show ap dot11 24ghz cleanair summary

This command has no arguments or keywords.

Command Modes

User EXEC  (>)

Privileged EXEC  (#)

Command History

Release Modification

Cisco IOS XE 3.3SE

This command was introduced.

Examples

This is an example of output from the show ap dot11 24ghz cleanair summary command:

Controller# show ap dot11 24ghz cleanair summary

AP Name               MAC Address         Slot ID  Spectrum Capable  Spectrum Intelligence   Spectrum Oper State
-----------------------------------------------------------------------------------------------------------------
AP1cdf.0f95.1719      0817.35c7.1a60            0  Disabled          Disabled                Down
AS-5508-5-AP3         0817.35dd.9f40            0  Disabled          Disabled                Down
AP270ca.9b86.4546     0c85.259e.c350            0  Enabled           Enabled                 Up
AP2894.0f26.22df      0c85.25ab.cca0            0  Enabled           Enabled                 Up
AP2894.0f58.cc6b      0c85.25c7.b7a0            0  Enabled           Enabled                 Up
AP2894.0f39.1040      0c85.25de.2c10            0  Enabled           Enabled                 Up
AP2894.0f63.c6da      0c85.25de.c8e0            0  Enabled           Enabled                 Up