Guest

Cisco Unified IP Phone 6900 Series

Cisco Unified Communications Manager Express 8.0 Support for DnD Feature Button and Unlocked MeetMe Conference (SCCP)

  • Viewing Options

  • PDF (181.2 KB)
  • Feedback
Cisco Unified Communications Manager Express 8.0 Support for DnD Feature Button and Unlocked MeetMe Conference (SCCP)

Table Of Contents

Cisco Unified
Communications Manager Express 8.0
Support for DnD Feature Button and Unlocked MeetMe Conference (SCCP)

Finding Feature Information

Contents

Prerequisites for Cisco Unified CME 8.0

Restrictions

Information About DnD Feature Button and Unlocked MeetMe Conference bridge On SCCP CUCME

DnD Feature Button

Unlocked MeetMe Conference

Unrestricted Display

After-hour Login HTTP

Configuring Line Button

Maximum Calls for a Button

How to Configure DnD Feature Button on Cisco Unified CME

Configuring DnD Feature button on Cisco Unified CME

How to Configure Unrestricted Display on Cisco Unified CME

Configuring Unrestricted Display on Cisco Unified CME

How to Configure after-hour login http on Cisco Unified CME

Configuring after-hour login http on Cisco Unified CME

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Cisco Unified CME 8.0


Cisco Unified
Communications Manager Express 8.0
Support for DnD Feature Button and Unlocked MeetMe Conference (SCCP)


This document describes support for the Do Not Disturb (DnD) feature button and Unlocked MeetMe Conference bridge for SCCP IP phones in Cisco Unified Communications Manager Express 8.0 (Cisco Unified CME).

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Cisco Unified CME 8.0" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

Prerequisites for Cisco Unified CME 8.0

Information About DnD Feature Button and Unlocked MeetMe Conference bridge On SCCP CUCME

How to Configure DnD Feature Button on Cisco Unified CME

How to Configure Unrestricted Display on Cisco Unified CME

How to Configure after-hour login http on Cisco Unified CME

Additional References

Feature Information for Cisco Unified CME 8.0

Prerequisites for Cisco Unified CME 8.0

Cisco Unified CME 8.0

Cisco IOS Release 15.1(1)T

Restrictions

When the user configures DN mode in single-line or dual-line mode, the corresponding configured DN mode for all fallback DNs is supported.

When you configure max-dn XX dual-octo or max-dn XX octo, the dual-line DN mode is applied to all DNs associated with the new Cisco Unified 6921, 6941 and 6961 IP phones.

In CME-as-SRST, if a user configures srst dn line-mode dual-octo or srst dn line-mode octo-line, dual-line DN mode will be applied to all srst-learned DNs associated with the Cisco Unified 69xx series IP phones.

The huntstop channel will be applied to the DNs associated with Cisco Unified 6921, 6941 and 6961 IP phones in SRST and CME-as-SRST.

In the Cisco Unified Communications Manager Express mode, Cisco Unified IP phone models 6921, 6941 and 6961 only supports one call per button. It is recommend to configure the Cisco Unified IP phones 6921, 6941 and 6961 dn as dual-line dn and the huntstop channel under the dn. The second channel on the dn can only be used for call transfer or conference. Button c (overlay call-waiting) and x (expansion/overflow) are not supported with Cisco Unified 6921, 6941 and 6961 IP phones.

In SRST, if call-forward busy is configured globally under call-manager-fallback, only apply call-forward busy on the last member of the fallback DNs set with the same extension number assigned on multiple buttons of the phone. If the fallback DN is unique, call-forward busy will be applied.

Information About DnD Feature Button and Unlocked MeetMe Conference bridge On SCCP CUCME

To configure DnD feature button and Unlocked MeetMe conference bridge on Cisco Unified CME 8.0, you should understand the following concepts:

DnD Feature Button

Unlocked MeetMe Conference

DnD Feature Button

Cisco Unified CME 8.0 adds support for new DnD feature button. The DnD feature button allows the user to configure a line button with Do not Disturb feature instead of using the DnD soft key. Press the button to enable or disable the DnD feature when the phone is idle. This feature button can also be used as Hunt Log (HLog) button if the hunt-group logout dnd is configured in the phone. When it is used as HLog button, press the button to activate or deactivate the DnD. The LED will be ON when the DnD feature is enabled and the LED will be OFF when the DnD feature is disabled.

Unlocked MeetMe Conference

Cisco Unified CME 8.0 adds support for Unlocked MeetMe Conference. When you unlock MeetMe conference bridge in Cisco Unified CME, the user can initiate a MeetMe conference without pressing the MeetMe soft key, which would allow the external callers to initiate a MeetMe conference.


Note In order to configure an unlocked MeetMe conference, all ephone-dn tags associated with the same number should have unlocked option configured. If some of the ephone-dn tags do not have unlocked option configured, unlocked MeetMe conference may not work properly.


Unrestricted Display

Cisco Unified CME 8.0 adds support for unrestricted message display. This command helps the user to define a set of attributes that describe the message display option of the ephone.

After-hour Login HTTP

Cisco Unified CME 8.0 adds support for after-hour login http. You can unblock the after-hour block to place outgoing calls regardless of whether the outgoing called number matches the defined pattern of digits during the call blocking periods.

When the user configures after-hours login http command, they will experience slightly different login behavior compare to the current one. The after-hours login mechanism is enhanced due to some User Interface (UI) limitation in the current model.

Configuring Line Button

In the Cisco Unified 69xx series IP phone, the first button should be always configured as Line button. If the first button is not configured as a line button, the phone does not display the title with the primary number. The Cisco Unified 6941 or 6961 ephone is configured with "button 2:1".

Maximum Calls for a Button

In the Cisco Unified Communication Manager Express mode, Cisco Unified IP phone models 6921, 6941, and 6961 only supports one call per button. It is recommend to configure the Cisco Unified IP phones 6921, 6941, and 6961 dn as dual-line dn and the huntstop channel under the dn. The second channel on the dn can only be used for call transfer or conference."

The Cisco Unified 7931 IP phone supports only two calls per button. When you attempt to configure max-calls-per-button more than two calls on the Cisco Unified 7931 IP phone, the max-call -per-button configuration will fail.

How to Configure DnD Feature Button on Cisco Unified CME

This section contains the following tasks.

Configuring DnD Feature button on Cisco Unified CME

Configuring DnD Feature button on Cisco Unified CME

To configure DnD Feature button on SCCP CUCME, perform the following steps:

SUMMARY STEPS

1. enable

2. configure terminal

3. ephone phone-tag

4. feature-button tag {dnd | privacy}

5. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ephone phone-tag

Example:

Router(config)# ephone 6


Enters ephone configuration mode.

phone-tag—Unique sequence number that identifies this ephone during configuration tasks. The maximum number of ephones is version and platform-specific. Type? to display range.

Step 4 

feature-button <tag> [feature id]

Example:

Router(config-ephone)# feature-button 1 dnd


Defines the feature button.

tag—Number of the feature button.

feature id—Name of the feature. It can be dnd or privacy.

Step 5 

end

Example:

Router(config-ephone)# end

Returns to privileged EXEC mode.

Examples

ephone  1
 feature-button 1 Dnd
 feature-button 2 Privacy
 mac-address 0017.E03F.B1E8
 type 7961

How to Configure Unrestricted Display on Cisco Unified CME

This section contains the following tasks.

Configuring Unrestricted Display on Cisco Unified CME

Configuring Unrestricted Display on Cisco Unified CME

To configure Unrestricted Display on SCCP CUCME, perform the following steps:

SUMMARY STEPS

1. enable

2. configure terminal

3. ephone phone-type

4. unrestricted-display

5. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ephone phone-type

Example:

Router(config)# ephone-type ABC


Enters ephone-type configuration mode.

phone-type—Defines the ethernet phone type.

Step 4 

unrestricted-display

Example:

Router(config-ephone-type)# unrestricted-display


Defines a set of attributes that describe the message display option of the ephone.

Step 5 

end

Example:

Router(config-ephone)# end

Returns to privileged EXEC mode.

Examples

Router#en
Router#configure terminal

Router(config)# ephone-type ABC

Router(config-ephone-type)# unrestricted-display

How to Configure after-hour login http on Cisco Unified CME

This section contains the following tasks.

Configuring Unrestricted Display on Cisco Unified CME

Configuring after-hour login http on Cisco Unified CME

To configure after-hour login http on SCCP CUCME, perform the following steps:

SUMMARY STEPS

1. enable

2. configure terminal

3. ephone phone-tag

4. Pin

5. after-hour login http

6. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ephone phone-tag

Example:

Router(config)# ephone 6


Enters ephone configuration mode.

phone-tag—Unique sequence number that identifies this ephone during configuration tasks. The maximum number of ephones is version and platform-specific. Type? to display range.

Step 4 

Pin

Example:

Router(config-ephone-type)#pin 123


Defines a pattern of digits for unblocking outgoing calls from IP phones.

Step 5 

after-hout login http

Example:

Router(config-ephone-type)#after-hour login http

Unblocks the outgoing calls from IP phones.

Step 6 

end

Example:

Router(config-ephone)# end

Returns to privileged EXEC mode.

Examples

Router(config)# ephone 6
Router(config-ephone)# mac 00e0.8646.9242
Router(config-ephone)# button 1:33
Router(config-ephone)# Pin 123
Router(config-ephone)# after-hour login http

Additional References

The following sections provide references related to Cisco Unified CME.

Related Documents


Standards

Standard
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIB
MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFC
Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.


Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport


Feature Information for Cisco Unified CME 8.0

Table 1 lists the release history for this feature.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.


Table 1 Feature Information for Cisco Unified CME 8.0 

Feature Name
Releases
Feature Information

Cisco Unified CME 8.0

15.1(1)T

Support for DnD feature button and Unlocked MeetMe Conference Bridge was added.