Cisco Unified Communications Manager Express System Administrator Guide
Configuring Directory Services
Downloads: This chapterpdf (PDF - 325.0KB) The complete bookPDF (PDF - 16.01MB) | Feedback

Table of Contents

Configuring Directory Services

Contents

Information About Directory Services

Local Directory

External Directory

Called-Name Display

Directory Search

How to Configure Directory Services

Configuring Local Directory Service

SCCP: Defining a Name for a Directory Number

Prerequisites

Restrictions

SCCP: Adding an Entry to a Local Directory

Restrictions

SCCP: Configuring External Directory Service

Prerequisites

Restrictions

Called-Name Display

Prerequisites

Restrictions

Verifying Called-Name Display

SIP: Defining a Name for a Directory Number

Prerequisites

SIP: Configuring External Directory Service

Prerequisites

Restrictions

Verifying Directory Services

Configuration Examples for Directory Services

Local Directory

Called-Name Display

First Ephone-dn in the Overlay Set: Example

Directory Name for an Overlaid Ephone-dn Set: Example

Directory Name for a Hunt Group with Overlaid Ephone-dns: Example

Directory Name for Non-Overlaid Ephone-dns: Example

Ephone-dn Name for Overlaid Ephone-dns: Example

Additional References

Related Documents

Technical Assistance

Feature Information for Directory Services

Configuring Directory Services

This chapter describes the directory services support available in Cisco Unified Communications Manager Express (Cisco Unified CME).

Finding Feature Information in This Module

Your Cisco Unified CME version may not support all of the features documented in this module. For a list of the versions in which each feature is supported, see the “Feature Information for Directory Services” section.

Information About Directory Services

To enable directory services, you should understand the following concepts:

Local Directory

Cisco Unified CME automatically creates a local phone directory containing the telephone numbers that are assigned in the directory number configuration of the phone. You can make additional entries to the local directory in telephony services configuration mode. Additional entries can be nonlocal numbers such as telephone numbers on other Cisco Unified CME systems used by your company.

When a phone user selects the Directories > Local Directory menu, the phone displays a search page from Cisco Unified CME. After a user enters the search information, the phone sends the information to Cisco Unified CME, which searches for the requested number or name pattern in the directory number configuration and sends the response back to the phone, which displays the matched results. The phone can display up to 32 directory entries. If a search results in more than 32 entries, the phone displays an error message and the user must refine the search criteria to narrow the results.

The order of the names in the directory entries is first-name-first or last-name-first. Character strings for directory names can contain a spaces and a comma (,) and cannot contain an ampersand (&).

The local directory that is displayed on an IP phone is an XML page that is accessed through HTTP without password protection. The directory HTTP service can be disabled to suppress the availability of the local directory.

For configuration information, see the “Configuring Local Directory Service” section.

External Directory

Cisco Unified IP Phones can support URLs in association with the four programmable feature buttons on IP phones, including the Directories button. Operation of these services is determined by the Cisco Unified IP phone capabilities and the content of the referenced URL. Provisioning the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.

Called-Name Display

When phone agents answer calls for several different departments or people, it is often helpful for them to see a display of the name, rather than the number, of the called party. For example, if order-entry agents are servicing three catalogs with individual 800 numbers configured in one overlay ephone-dn set, they need to know which catalog is being called to give the correct greeting, such as “Thank you for calling catalog N . May I take your order?” The called-name display feature can display either of the following types of name:

  • Name for a directory number in a local directory
  • Name associated with an overlay directory number. Calls to the first directory number in a set of overlay numbers will display a caller ID. Calls to the remaining directory numbers in the overlay set will display the name associated with the directory number.

Directory Search

Cisco Unified CME 4.3 increases the number of entries supported in a search results list from 32 to up to 240 when using the directory search feature. For example, if a user enters “smith” as the last name, all 240 matches are displayed on eight different pages, with 30 entries per page. If multiple pages are required, the phone displays two new soft keys, “Next” and “Prev” that the phone user can press to move back and forth between the previous and next pages. Text such as “Page 2 of 3" displays to indicate the current and total pages on the search results.

How to Configure Directory Services

This section contains the following tasks:

Configuring Local Directory Service

To define the format for local directory names or block the local directory display on all phones, perform the following steps.

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony-service

4. directory { first-name-first | last-name-first }

5. no service local-directory

6. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

telephony-service

 

Router(config)# telephony-service

Enters telephony-service configuration mode.

Step 4

directory { first-name-first | last-name-first }

 

Router(config-telephony)# directory last-name-first

Defines the format for entries in the local directory.

  • Default is first-name-first .

Step 5

no service local-directory

 

Router(config-telephony)# no service local-directory

Disables local directory service on IP phones.

Step 6

end

 

Router(config-telephony)# end

Returns to privileged EXEC mode.

SCCP: Defining a Name for a Directory Number

To define a name to be used for caller-ID displays and as a local directory entry, perform the following steps.

Prerequisites

  • Cisco CME 3.0 or a later version.
  • Directory number for which you are defining a directory entry must already have a number assigned by using the number (ephone- dn) command. For configuration information, see SCCP: Creating Directory Numbers.

Restrictions

  • The name to be associated with a directory number cannot contain special characters, such as an ampersand (&). The only special characters allowed in the name are the comma (,) and the percent sign (%).

SUMMARY STEPS

1. enable

2. configure terminal

3. ephone-dn dn-tag

4. name name

5. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

ephone-dn dn-tag

 

Router(config)# ephone-dn 55

Enters ephone-dn configuration mode.

Step 4

name name

 

Router(config-ephone-dn)# name Smith, John

or

Router(config-ephone-dn)# name Shipping and Handling

Associates a name with this directory number.

  • Must follow the name order that is specified with the directory command: first-name-first or last-name-first.
  • name —Alphanumeric string to be displayed.

You must separate the two parts, first last or last first, of the name string with a space.

The second part of the name string can contain spaces, such as “and Shipping.” The first part of the name string cannot contain spaces.

You can include a comma (,) in the name string for display purposes, for example, when you use the last-name-first pattern (last, first).

Step 5

end

 

Router(config-telephony)# end

Returns to privileged EXEC mode.

SCCP: Adding an Entry to a Local Directory

To add an entry to the local directory, perform the following steps.

Restrictions

  • If the directory entry being configured is to be used for called-name display, the number being configured must contain at least one wildcard character.
  • Entry for local directory cannot include opening or closing quotation marks (‘, ‘, “, or ”).

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony-service

4. directory entry { directory-tag number name name | clear}

5. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

telephony-service

 

Router(config)# telephony-service

Enters telephony-service configuration mode.

Step 4

directory entry { directory-tag number name name | clear }

 

Router(config-telephony)# directory entry 1 5550111 name Sales

Creates a telephone directory entry that is displayed on an IP phone. Entries appear in the order in which they are entered.

  • directory-tag—Unique sequence number that identifies this directory entry during all configuration tasks. Range is 1 to 250.
  • If this name is to be used for called-name display, the number associated with the names must contain at least one wildcard character.
  • name —1 to 24 alphanumeric characters, including spaces. Name cannot include opening or closing quotation marks (‘, ’ , “, or ”).

Step 5

end

 

Router(config-telephony)# end

Returns to privileged EXEC mode.

SCCP: Configuring External Directory Service

To enable an external directory resource on supported Cisco Unified IP phones and disable local directory services on those same phones, perform the following steps.

Prerequisites

To use a Cisco Unified Communications Manager directory as an external directory source for Cisco Unified CME phones, the Cisco Unified Communications Manager must be made aware of the phones. You must list the MAC addresses of the Cisco Unified CME phones in the Cisco Unified Communications Manager and reset the phones from the Cisco Unified Communications Manager. It is not necessary for you to assign ephone-dns to the phones or for the phones to register with Cisco Unified Communications Manager.

Restrictions

  • Provisioning of the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.
  • Configuring external directory service only works with non-Java based phones. Any Java based phone will display duplicate directories for the following:

Missed

Received

Placed

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony -service

4. url directories url

5. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

telephony-service

 

Router(config)# telephony-service

Enters telephony-service configuration mode.

Step 4

url directories url

 

Router(config-telephony)# url directories http://10.0.0.11/localdirectory

Associates a URL with the programmable Directories feature button on supported Cisco Unified IP phones in Cisco Unified CME.

  • Provisioning the directories URL to select an external directory resource disables the Cisco Unified CME local directory service.
  • Operation of these services is determined by the Cisco Unified IP phone capabilities and the content of the specified URL.

Step 5

end

 

Router(config-telephony)# end

Exits configuration mode and enters privileged EXEC mode.

Called-Name Display

To enable called-name display, perform the following steps.

Prerequisites

Restrictions

  • The service dnis overlay command can only be used to configure overlaid ephone-dns.

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony-service

4. service dnis dir-lookup

5. service dnis overlay

6. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

telephony-service

 

Router(config)#

Enters telephony-service configuration mode.

Step 4

service dnis dir-lookup

 

Router(config-telephony)# service dnis dir-lookup

Specifies that incoming calls to a called number should display the name that was defined for this directory number with the directory entry command.

  • If the service dnis dir-lookup and service dnis overlay commands are both used in one configuration, the service dnis dir-lookup command takes precedence.

Step 5

service dnis overlay

 

Router(config-telephony)# service dnis overlay

(For overlaid directory numbers only.) Specifies that incoming calls to a called number should display the name that was defined for this directory number with the name command.

Note If the service dnis dir-lookup and service dnis overlay commands are both used in one configuration, the service dnis dir-lookup command takes precedence.

Step 6

end

 

Router(config-telephony)# end

Returns to privileged EXEC mode.

Verifying Called-Name Display


Step 1 Use the show running-config command to verify your configuration. Called-name display is shown in the telephony-service part of the output.

Router# show running-config

telephony-service

service dnis overlay

Step 2 Use the show telephony-service directory-entry command to display current directory entries.

Router# show telephony-service directory-entry

directory entry 1 5550341 name doctor1

directory entry 2 5550772 name doctor1

directory entry 3 5550263 name doctor3

Step 3 Use the show telephony-service ephone-dn command to verify that you have used at least one wildcard (period or .) in the ephone-dn primary or secondary number or to verify that you have entered a name for the number.

Router# show telephony-service ephone-dn

ephone-dn 2

number 5002 secondary 200.

name catalogN

huntstop

call-forward noan 5001 timeout 8

Step 4 Use the show ephone overlay command to verify the contents of overlaid ephone-dn sets.

Router# show ephone overlay

ephone-1 Mac:0007.0EA6.353A TCP socket:[1] activeLine:0 REGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0

IP:10.2.225.205 52486 Telecaster 7960 keepalive 2771 max_line 6

button 1: dn 11 number 60011 CH1 IDLE overlay

button 2: dn 17 number 60017 CH1 IDLE overlay

button 3: dn 24 number 60024 CH1 IDLE overlay

button 4: dn 30 number 60030 CH1 IDLE overlay

button 5: dn 36 number 60036 CH1 IDLE CH2 IDLE overlay

button 6: dn 39 number 60039 CH1 IDLE CH2 IDLE overlay

overlay 1: 11(60011) 12(60012) 13(60013) 14(60014) 15(60015) 16(60016)

overlay 2: 17(60017) 18(60018) 19(60019) 20(60020) 21(60021) 22(60022)

overlay 3: 23(60023) 24(60024) 25(60025) 26(60026) 27(60027) 28(60028)

overlay 4: 29(60029) 30(60030) 31(60031) 32(60032) 33(60033) 34(60034)

overlay 5: 35(60035) 36(60036) 37(60037)

overlay 6: 38(60038) 39(60039) 40(60040


 

SIP: Defining a Name for a Directory Number

To define name for a directory number on a SIP phone, perform the following steps.

Prerequisites

  • Cisco CME 3.4 or a later version.
  • Directory number for which you are defining a name must already have a number assigned by using the number (voice register dn) command. For configuration information, see SIP: Creating Directory Numbers.

SUMMARY STEPS

1. enable

2. configure terminal

3. voice register dn dn-tag

4. name name

5. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

voice register dn dn-tag

 

Router(config-register-global)# voice register dn 17

Enters voice register dn configuration mode to define a directory number for a SIP phone, intercom line, voice port, or a message-waiting indicator (MWI).

Step 4

name name

 

Router(config-register-dn)# name Smith, John

or

 

Router(config-register-dn)# name John Smith

Associates a name with a directory number in Cisco Unified CME and provides caller ID for calls originating from a SIP phone.

  • Name must follow the order specified by using the directory (telephony-service) command.

Step 5

end

 

Router(config-register-dn)# end

Exits configuration mode and enters privileged EXEC mode.

SIP: Configuring External Directory Service

To enable an external directory resource on supported Cisco Unified IP phones and disable local directory services on those same phones, perform the following steps.

Prerequisites

Cisco CME 3.4 or a later version.

Restrictions

  • Provisioning of the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.
  • Supported only on Cisco Unified IP Phone 7960s and 7960Gs and Cisco Unified IP Phone 7940s and 7940Gs.

SUMMARY STEPS

1. enable

2. configure terminal

3. voice register global

4. url directory url

5. end

DETAILED STEPS

Command or Action
Purpose

Step 1

enable

 

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

 

Router# configure terminal

Enters global configuration mode.

Step 3

voice register global

 

Router(config)# voice register global

Enters voice register global configuration mode to set parameters for all supported SIP phones in Cisco Unified CME.

Step 4

url { directory url

 

Router(config-register-global)# url directory http://10.0.0.11/localdirectory

Associates a URL with the programmable Directories feature button on supported Cisco Unified IP phones in Cisco Unified CME.

  • Provisioning the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.
  • Operation of these services is determined by the Cisco Unified IP phone capabilities and the content of the specified URL.

Step 5

end

 

Router(config-register-global)# end

Exits to privileged EXEC mode.

Verifying Directory Services

To verify the configuration for local directory services, perform the following steps.

SUMMARY STEPS

1. show running-config

2. show telephony-service

3. show telephony-service directory-entry

DETAILED STEPS


Step 1 show running-config

This command displays the running configuration. Directory configuration commands are listed in the telephony-service portion of the output.

Router# show running-config
.
.
.
timeout busy 10
timeout ringing 100
caller-id name-only: enable
system message XYZ Company
web admin system name admin1 password admin1
web admin customer name Customer
edit DN through Web: enabled.
edit TIME through web: enabled.
Log (table parameters):
max-size: 150
retain-timer: 15
create cnf-files version-stamp Jan 01 2002 00:00:00
transfer-system full-consult
multicast moh 239.12.20.123 port 2000
fxo hook-flash
local directory service: enabled.

Step 2 show telephony-service

This command displays only the telephony-service configuration information.

Step 3 Use the show telephony-service directory-entry command to display the entries made using the directory entry command.


 

Configuration Examples for Directory Services

This section contains the following examples:

Local Directory

The following example defines the naming order for the local directory on IP phones served by the Cisco Unified CME router:

telephony-service

directory last-name-first

The following example creates a directory of three telephone listings:

telephony-service

directory entry 1 14045550111 name Sales

directory entry 2 13125550122 name Marketing

directory entry 3 12135550144 name Support Center

The following example disables the local directory on IP phones served by the Cisco Unified CME router:

telephony-service

no service local-directory

First Ephone-dn in the Overlay Set: Example

The following example shows a configuration for three phones that use the same set of overlaid ephone-dns for each phone’s button 1.

telephony-service

service dnis overlay

ephone-dn 1

number 18005550100

ephone-dn 2

name department1

number 18005550101

ephone-dn 3

name department2

number 18005550102

ephone 1

button 1o1,2,3

ephone 2

button 1o1,2,3

ephone 3

button 1o1,2,3

The default display for all three phones is the number of the first ephone-dn listed in the overlay set (18005550100). A call is made to the first ephone-dn (18005550100), and the caller ID (for example, 4085550123) is displayed on all three phones. The user for phone 1 answers the call. The caller ID (4085550123) remains displayed on phone 1, and the displays on phone 2 and phone 3 return to the default display (18005550100). A call to the next ephone-dn is made. The default display on phone 2 and phone 3 is replaced with the called ephone-dn’s name (18005550101).

Directory Name for an Overlaid Ephone-dn Set: Example

The following is an example of a configuration of overlaid ephone-dns that uses wildcards in the secondary numbers for the ephone-dns. The wildcards allow you to control the display according to the number that was dialed. The example is for a medical answering service with three IP phones that accept calls for nine doctors on one button. When a call to 5550001 rings on button 1 on ephone 1 through ephone 3, “doctor1” is displayed on all three ephones.

telephony-service

service dnis dir-lookup

directory entry 1 5550001 name doctor1

directory entry 2 5550002 name doctor2

directory entry 3 5550003 name doctor3

directory entry 4 5550010 name doctor4

directory entry 5 5550011 name doctor5

directory entry 6 5550012 name doctor6

directory entry 7 5550020 name doctor7

directory entry 8 5550021 name doctor8

directory entry 9 5550022 name doctor9

ephone-dn 1

number 5500 secondary 555000.

ephone-dn 2

number 5501 secondary 555001.

ephone-dn 3

number 5502 secondary 555002.

ephone 1

button 1o1,2,3

mac-address 1111.1111.1111

ephone 2

button 1o1,2,3

mac-address 2222.2222.2222

ephone 3

button 1o1,2,3

mac-address 3333.3333.3333

For more information about making directory entries, see the “Local Directory” section. For more information about overlaid ephone-dns, see Configuring Call Coverage Features.

Directory Name for a Hunt Group with Overlaid Ephone-dns: Example

The following example shows a hunt-group configuration for a medical answering service with two phones and four doctors. Each phone has two buttons, and each button is assigned two doctors’ numbers. When a patient calls 5550341, Cisco Unified CME matches the hunt-group pilot secondary number (555....), rings button 1 on one of the two phones, and displays “doctor1.”

telephony-service

service dnis dir-lookup

max-redirect 20

directory entry 1 5550341 name doctor1

directory entry 2 5550772 name doctor1

directory entry 3 5550263 name doctor3

directory entry 4 5550150 name doctor4

ephone-dn 1

number 1001

ephone-dn 2

number 1002

ephone-dn 3

number 1003

ephone-dn 4

number 104

ephone 1

button 1o1,2

button 2o3,4

mac-address 1111.1111.1111

ephone 2

button 1o1,2

button 2o3,4

mac-address 2222.2222.2222

ephone-hunt 1 peer

pilot 5100 secondary 555....

list 1001, 1002, 1003, 1004

final number 5556000

hops 5

preference 1

timeout 20

no-reg

For more information about hunt-group behavior, see Configuring Call Coverage Features. Note that wildcards are used only in secondary numbers and cannot be used with primary numbers. For more information about making directory entries, see the “Local Directory” section. For more information about overlaid ephone-dns, see Configuring Call Coverage Features.

Directory Name for Non-Overlaid Ephone-dns: Example

The following is a configuration for three IP phones, each with two buttons. Button 1 receives calls from doctor1, doctor2, and doctor3, and button 2 receives calls from doctor4, doctor5, and doctor6.

telephony-service

service dnis dir-lookup

directory entry 1 5550001 name doctor1

directory entry 2 5550002 name doctor2

directory entry 3 5550003 name doctor3

directory entry 4 5550010 name doctor4

directory entry 5 5550011 name doctor5 directory entry 6 5550012 name doctor6

ephone-dn 1

number 1001 secondary 555000.

 

ephone-dn 2

number 1002 secondary 555001.

ephone 1

button 1:1

button 2:2

mac-address 1111.1111.1111

ephone 2

button 1:1

button 2:2

mac-address 2222.2222.2222

ephone 3

button 1:1

button 2:2

mac-address 3333.3333.3333

For more information about making directory entries, see the “Local Directory” section.

Ephone-dn Name for Overlaid Ephone-dns: Example

The following example shows three phones that have button 1 assigned to pick up three 800 numbers for three different catalogs.

The default display for all four phones is the number of the first ephone-dn listed in the overlay set (18005550000). A call is made to the first ephone-dn (18005550000), and the caller ID (for example, 4085550123) is displayed on all phones. The user for phone 1 answers the call. The caller ID (4085550123) remains displayed on phone 1, and the displays on phone 2 and phone 3 return to the default display (18005550000). A call to the second ephone-dn (18005550001) is made. The default display on phone 2 and phone 3 is replaced with the called ephone-dn's name (catalog1) and number (18005550001).

telephony-service

service dnis overlay

ephone-dn 1

number 18005550000

ephone-dn 2

name catalog1

number 18005550001

ephone-dn 3

name catalog2

number 18005550002

ephone-dn 4

name catalog3

number 18005550003

ephone 1

button 1o1,2,3,4

ephone 2

button 1o1,2,3,4

ephone 3

button 1o1,2,3,4

For more information about overlaid ephone-dns, see Configuring Call Coverage Features.

Additional References

The following sections provide references related to Cisco Unified CME features.

Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport

Feature Information for Directory Services

Table 21-1 lists the features in this module and enhancements to the features by version.

To determine the correct Cisco IOS release to support a specific Cisco Unified CME version, see the Cisco Unified CME and Cisco IOS Software Version Compatibility Matrix at http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm .

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on Cisco.com is not required.


NoteTable 21-1 lists the Cisco Unified CME version that introduced support for a given feature. Unless noted otherwise, subsequent versions of Cisco Unified CME software also support that feature.


 

Table 21-1 Feature Information for Directory Services

Feature Name
Cisco Unified CME
Version
Feature Information

Directory Search

7.0/4.3

Number of entries supported in a search results list was increased from 32 to 240 when using directory search.

Called-Name Display

3.2

Called-name display was introduced.

Local Directory Service
External Directory Service

4.0(2)

Added support for transferring a call directly to a selected number listed in the directory. If directory transfer is not supported, the user must press Transfer and then use the keypad to manually enter the number of the monitored line to transfer the incoming call.

3.4

Added support of directory services for SIP phones directly connected in Cisco Unified CME.

3.0

The ability to add local directory entries in addition to those that are automatically added from phone configurations was introduced. Authentication for local directory display was introduced.

2.1

The ability to block the display of the local directory on phones was introduced.

2.0

The specification of name format in the local directory was introduced.