AnnunciatorOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate an annunciator resource from those that are registered to a Unified Communications Manager when none were available.
|
AnnunciatorResourceActive
|
This counter represents the total number of annunciator resources that are currently in use on all annunciator devices that
are registered with a Unified Communications Manager.
|
AnnunciatorResourceAvailable
|
This counter
represents the total number of annunciator resources that are not active and
are currently available.
|
AnnunciatorResourceTotal
|
This counter represents the total number of annunciator resources that are provided by all annunciator devices that are currently
registered with Unified Communications Manager.
|
AuthenticatedCallsActive
|
This counter represents the number of authenticated calls that are currently active (in use) on Unified Communications Manager. An authenticated call designates one in which all the endpoints that are participating in the call are authenticated. An
authenticated phone uses the Transport Layer Security (TLS) authenticated Skinny protocol signaling with Unified Communications Manager.
|
AuthenticatedCallsCompleted
|
This counter represents the number of authenticated calls that connected and subsequently disconnected through Unified Communications Manager. An authenticated call designates one in which all the endpoints that are participating in the call are authenticated. An
authenticated phone uses the TLS authenticated Skinny protocol signaling with Unified Communications Manager.
|
AuthenticatedPartiallyRegisteredPhone
|
This counter
represents the number of partially registered, authenticated SIP phones.
|
AuthenticatedRegisteredPhones
|
This counter represents the total number of authenticated phones that are registered to Unified Communications Manager. An authenticated phone uses the TLS authenticated Skinny protocol signaling with Unified Communications Manager.
|
BRIChannelsActive
|
This counter represents the number of BRI voice channels that are currently in an active call on this Unified Communications Manager.
|
BRISpansInService
|
This counter
represents the number of BRI spans that are currently available for use.
|
CallManagerHeartBeat
|
This counter represents the heartbeat of Unified Communications Manager. This incremental count indicates that Cisco Unified Communications Manager is up and running. If the count does not increment, that indicates that Unified Communications Manager is down.
|
CallsActive
|
This counter represents the number of voice or video streaming connections that are currently in use (active); in other words,
the number of calls that actually have a voice path that is connected on Unified Communications Manager.
|
CallsAttempted
|
This counter
represents the total number of attempted calls. An attempted call occurs any
time that a phone goes off hook and back on hook, regardless of whether any
digits were dialed, or whether it connected to a destination. The system
considers some call attempts during feature operations (such as transfer and
conference) to be attempted calls.
|
CallsCompleted
|
This counter represents the number of calls that were actually connected (a voice path or video stream was established) through
Unified Communications Manager. This number increases when the call terminates.
|
CallsInProgress
|
This counter represents the number of voice or video calls that are currently in progress on Unified Communications Manager, including all active calls.
When a
phone that is registered with Skinny Client Control Protocol (SCCP) goes off
hook, the CallsInProgress progress counter increments until it goes back on
hook.
For
Cisco Unified IP
Phones 7940, and 7960 that register with SIP, the CallsInProgress
counter increments when the dial softkey is pressed.
For all
other phones that are running SIP, the CallsInProgress counter increments when
the first digit is pressed.
When all
voice or video calls that are in progress are connected, the number of
CallsInProgress represents the number of CallsActive. The counter decreases by
one when a phone goes back on hook.
|
CM_MediaTermPointsRequestsThrottled
|
This counter represents the total number of media termination point (MTP) resource requests that have been denied due to throttling
(a resource from this MTP was not allocated because, as specified by the Cisco CallManager service parameter, MTP and Transcoder
Resource Throttling Percentage, the MTP was being utilized beyond the configured throttle percentage). This counter increments
each time a request for an MTP on this Unified Communications Manager node is requested and denied due to MTP throttling and reflects a running total since the start of the Cisco CallManager
service.
|
CM_TranscoderRequestsThrottled
|
This counter represents the total number of transcoder resource requests that have been denied due to throttling (a resource
from this transcoder was not allocated because, as specified by the Cisco CallManager service parameter MTP and Transcoder
Resource Throttling Percentage, the transcoder was being utilized beyond the configured throttle percentage). This counter
increments each time a request for a transcoder on this Unified Communications Manager node is requested and denied due to transcoder throttling and reflects a running total since the start of the Cisco CallManager
service
|
EncryptedCallsActive
|
This counter represents the number of encrypted calls that are currently active (in use) on this Unified Communications Manager. An encrypted call represents one in which all the endpoints that are participating in the call are encrypted.
|
EncryptedCallsCompleted
|
This counter represents the number of encrypted calls that were connected and subsequently disconnected through this Unified Communications Manager. An encrypted call represents one in which all the endpoints that are participating in the call are encrypted.
|
EncryptedPartiallyRegisteredPhones
|
This
counter represents the number of partially registered, encrypted SIP phones.
|
EncryptedRegisteredPhones
|
This counter represents the total number of encrypted phones that are registered on this Unified Communications Manager.
|
FXOPortsActive
|
This counter represents the number of FXO ports that are currently in use (active) on a Unified Communications Manager.
|
FXOPortsInService
|
This
counter represents the number of FXO ports that are currently available for use
in the system.
|
FXSPortsActive
|
This counter represents the number of FXS ports that are currently in use (active) on a Unified Communications Manager.
|
FXSPortsInService
|
This
counter represents the number of FXS ports that are currently available for use
in the system.
|
HuntListsInService
|
This counter represents the number of hunt lists that are currently in service on Unified Communications Manager.
|
HWConferenceActive
|
This counter represents the total number of hardware conference resources that are provided by all hardware conference bridge
devices that are currently registered with Unified Communications Manager.
|
HWConferenceCompleted
|
This counter represents the total number of conferences that used a hardware conference bridge (hardware-based conference
devices such as Cisco Catalyst 6000, Cisco Catalyst 4000, Cisco VG200, Cisco series 26xx and 36xx) that is allocated from
Unified Communications Manager and that have completed, which means that the conference bridge has been allocated and released. A conference activates when
the first call connects to the bridge. The conference completes when the last call disconnects from the bridge.
|
HWConferenceOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate a hardware conference resource from those that are registered to a Unified Communications Manager when none was available.
|
HWConferenceResourceActive
|
This counter represents the total number of conference resources that are in use on all hardware conference devices (such
as Cisco Catalyst 6000, Catalyst 4000, Cisco VG200, Cisco series 26xx and 36xx) that are registered with Unified Communications Manager. System considers conference to be active when one or more calls are connected to a bridge.
|
HWConferenceResourceAvailable
|
This counter represents the number of hardware conference resources that are not in use and that are available to be allocated
on all hardware conference devices (such as Cisco Catalyst 6000, Cisco Catalyst 4000, Cisco VG200, Cisco series 26xx and 36xx)
that are allocated from Unified Communications Manager and that have been completed, which means that the conference bridge has been allocated and released. A conference activates
when the first call connects to the bridge. The conference completes when the last call disconnects from the bridge.
|
HWConferenceResourceTotal
|
This counter represents the number of active conferences on all hardware conference devices that are registered with Unified Communications Manager.
|
InitializationState
|
This counter represents the current initialization state of Unified Communications Manager. Unified Communications Manager includes the following initialization state values:
1-Database; 2-Regions; 3-Locations; 4-QoS Policy; 5-Time Of Day;
6-AAR Neighborhoods; 7-Digit Analysis; 8-Route Plan; 9-Call Control; 10-RSVP
Session Manager; 11-Supplementary Services; 12-Directory; 13-SDL Link;
14-Device; 100-Initialization Complete.
Not all
states display when this counter is used. This does not indicate that an error
occurred; it simply indicates that the state(s) initialized and completed
within the refresh period of the performance monitor.
|
LocationOutOfResources
|
This
counter represents the total number of times that a call through Locations
failed due to the lack of bandwidth.
|
MOHMulticastResourceActive
|
This counter represents the total number of multicast MOH resources that are currently in use (active) on all MOH servers
that are registered with a Unified Communications Manager.
|
MOHMulticastResourceAvailable
|
This counter represents the total number of active multicast MOH connections that are not being used on all MOH servers that
are registered with a Unified Communications Manager.
|
MOHOutOfResources
|
This counter represents the total number of times that the Media Resource Manager attempted to allocate an MOH resource when
all available resources on all MOH servers that are registered with a Unified Communications Manager were already active.
|
MOHTotalMulticastResources
|
This counter represents the total number of multicast MOH resources or connections that are provided by all MOH servers that
are currently registered with a Unified Communications Manager.
|
MOHTotalUnicastResources
|
This counter represents the total number of unicast MOH resources or streams that are provided by all MOH servers that are
currently registered with Unified Communications Manager. Each MOH unicast resource uses one stream.
|
MOHUnicastResourceActive
|
This counter represents the total number of unicast MOH resources that are currently in use (active) on all MOH servers that
are registered with Unified Communications Manager. Each MOH unicast resource uses one stream.
|
MOHUnicastResourceAvailable
|
This counter represents the total number of unicast MOH resources that are currently available on all MOH servers that are
registered with Unified Communications Manager. Each MOH unicast resource uses one stream.
|
MTPOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted but failed to allocate an MTP resource from one MTP device that is registered with Unified Communications Manager. This also means that no transcoders were available to act as MTPs.
|
MTPResourceActive
|
This counter represents the total number of MTP resources that are currently in use (active) on all MTP devices that are registered
with a Unified Communications Manager. Each MTP resource uses two streams. An MTP in use represents one MTP resource that has been allocated for use in a call.
|
MTPResourceAvailable
|
This counter represents the total number of MTP resources that are not in use and are available to be allocated on all MTP
devices that are registered with Unified Communications Manager. Each MTP resource uses two streams. An MTP in use represents one MTP resource that has been allocated for use in a call.
|
MTPResourceTotal
|
This counter represents the total number of media termination point (MTP) resources that are provided by all MTP devices that
are currently registered with Unified Communications Manager.
|
MTP_RequestsThrottled
|
This
counter represents the total number of media termination point (MTP) resource
requests that have been denied due to throttling (a resource from this MTP was
not allocated because, as specified by the Cisco CallManager service parameter
MTP and Transcoder Resource Throttling Percentage, the MTP was being utilized
beyond the configured throttle percentage). This counter increments each time a
resource is requested from this MTP and is denied due to throttling. This
counter reflects a running total since the MTP device registered with the Cisco
CallManager service.
|
PartiallyRegisteredPhone
|
This
counter represents the number of partially registered phones that are running
SIP.
|
PRIChannelsActive
|
This counter represents the number of PRI voice channels that are in an active call on a Unified Communications Manager.
|
PRISpansInService
|
This
counter represents the number of PRI spans that are currently available for
use.
|
RegisteredAnalogAccess
|
This
counter represents the number of registered Cisco analog access gateways that
are registered with system. The count does not include the number of Cisco
analog access ports.
|
RegisteredHardwarePhones
|
This
counter represents the number of Cisco hardware IP phones (for example,
Cisco Unified IP
Phones 7960, 7940, and so on) that are currently registered in
the system.
|
RegisteredMGCPGateway
|
This
counter represents the number of MGCP gateways that are currently registered in
the system.
|
RegisteredOtherStationDevices
|
This
counter represents the number of station devices other than Cisco hardware IP
phones that are currently registered in the system (for example,
Cisco IP SoftPhone, CTI port, CTI route point, Cisco voice-mail port).
|
SIPLineServerAuthorizationChallenges
|
This counter represents the number of authentication challenges for incoming SIP requests that the Unified Communications Manager server issued to phones that are running SIP. An authentication challenge occurs when a phone that is running SIP with Digest
Authentication enabled sends a SIP line request to Unified Communications Manager.
|
SIPLineServerAuthorizationFailures
|
This counter represents the number of authentication challenge failures for incoming SIP requests from SIP phones to the Unified Communications Manager server. An authentication failure occurs when a SIP phone with Digest Authentication enabled sends a SIP line request with
bad credentials to Unified Communications Manager.
|
SIPTrunkAuthorization
|
This counter represents the number of application-level authorization checks for incoming SIP requests that Unified Communications Manager has issued to SIP trunks. An application-level authorization check occurs when Unified Communications Manager compares an incoming SIP request to the application-level settings on the SIP Trunk Security Profile Configuration window
in Cisco Unified Communications Manager Administration.
|
SIPTrunkAuthorizationFailures
|
This counter represents the number of application-level authorization failures for incoming SIP requests that have occurred
on Unified Communications Manager SIP trunks. An application-level authorization failure occurs when Unified Communications Manager compares an incoming SIP request to the application-level authorization settings on the SIP Trunk Security Profile Configuration
window in Cisco Unified Communications Manager Administration and finds that authorization for one or more of the SIP features on that window is not allowed.
|
SIPTrunkServerAuthenticationChallenges
|
This counter represents the number of authentication challenges for incoming SIP requests that Unified Communications Manager issued to SIP trunks. An authentication challenge occurs when a SIP trunk with Digest Authentication enabled sends a SIP
request to Unified Communications Manager.
|
SIPTrunkServerAuthenticationFailures
|
This counter represents the number of authentication challenge failures that occurred for incoming SIP requests from SIP trunks
to Unified Communications Manager. An authentication failure occurs when a SIP trunk with Digest Authentication enabled sends a SIP request with bad credentials
to Unified Communications Manager.
|
SWConferenceActive
|
This counter represents the number of active conferences on all software conference devices that are registered with Unified Communications Manager.
|
SWConferenceCompleted
|
This counter represents the total number of conferences that used a software conference bridge that was allocated from a Unified Communications Manager and that have been completed, which means that the conference bridge has been allocated and released. A conference activates
when the first call connects to the bridge. The conference completes when the last call disconnects from the bridge.
|
SWConferenceOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate a software conference resource from those that are registered to Unified Communications Manager when none was available. Counter includes failed attempts to add a new participant to an existing conference.
|
SWConferenceResourceActive
|
This counter represents the total number of conference resources that are in use on all software conference devices that are
registered with Unified Communications Manager. The system considers a conference to be active when one or more calls connect to a bridge. One resource equals one stream.
|
SWConferenceResourceAvailable
|
This counter represents the number of new software-based conferences that can be started at the same time, for Unified Communications Manager. You must have a minimum of three streams available for each new conference. One resource equals one stream
|
SWConferenceResourceTotal
|
This counter represents the total number of software conference resources that are provided by all software conference bridge
devices that are currently registered with Unified Communications Manager.
|
SystemCallsAttempted
|
This
counter represents the total number of server-originated calls and attempted
calls to the Unity message waiting indicator (MWI).
|
T1ChannelsActive
|
This counter represents the number of T1 CAS voice channels that are in an active call on a Unified Communications Manager.
|
T1SpansInService
|
This
counter represents the number of T1 CAS spans that are currently available for
use.
|
TLSConnectedSIPTrunks
|
This
counter represents the number of SIP trunks that are configured and connected
via Transport Layer Security (TLS).
|
TLSConnectedWSM
|
This
counter represents the number of WSM Connectors that are configured and
connected to Motorola WSM via Transport Layer Security (TLS).
|
TranscoderOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate a transcoder resource from a transcoder device that is registered to a Unified Communications Manager when none was available.
|
TranscoderResourceActive
|
This counter represents the total number of transcoders that are in use on all transcoder devices that are registered with
Unified Communications Manager. A transcoder in use represents one transcoder resource that has been allocated for use in a call. Each transcoder resource
uses two streams.
|
TranscoderResourceAvailable
|
This counter represents the total number of transcoders that are not in use and that are available to be allocated on all
transcoder devices that are registered with Unified Communications Manager. Each transcoder resource uses two streams.
|
TranscoderResourceTotal
|
This counter represents the total number of transcoder resources that are provided by all transcoder devices that are currently
registered with Unified Communications Manager.
|
VCBConferenceActive
|
This counter represents the total number of active video conferences on all video conference bridge devices that are registered
with Unified Communications Manager.
|
VCBConferenceAvailable
|
This counter represents the total number of new video conferences on all video conference bridge devices that are registered
with Unified Communications Manager.
|
VCBConferenceCompleted
|
This counter represents the total number of video conferences that used a video conference bridge that are allocated from
Unified Communications Manager and that have been completed, which means that the conference bridge has been allocated and released. A conference activates
when the first call connects to the bridge. The conference completes when the last call disconnects from the bridge.
|
VCBConferenceTotal
|
This counter represents the total number of video conferences that are supported on all video conference bridge devices that
are registered with Unified Communications Manager.
|
VCBOutOfConferences
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate a video conference resource from those that are registered to Unified Communications Manager when none was available.
|
VCBOutOfResources
|
This
counter represents the total number of failed new video conference requests. A
conference request can fail because, for example, the configured number of
conferences is already in use.
|
VCBResourceActive
|
This counter represents the total number of video conference resources that are currently in use on all video conference devices
that are registered with Unified Communications Manager.
|
VCBResourceAvailable
|
This
counter represents the total number of video conference resources that are not
active and are currently available.
|
VCBResourceTotal
|
This counter represents the total number of video conference resources that are provided by all video conference bridge devices
that are currently registered with Unified Communications Manager.
|
VideoCallsActive
|
This counter represents the number of active video calls with active video streaming connections on all video conference bridge
devices that are registered with Unified Communications Manager.
|
VideoCallsCompleted
|
This
counter represents the number of video calls that were actually connected with
video streams and then released.
|
VideoOutOfResources
|
This counter represents the total number of times that Unified Communications Manager attempted to allocate a video-streaming resource from one of the video conference bridge devices that is registered to Unified Communications Manager when none was available.
|
XCODE_RequestsThrottled
|
This
counter represents the total number of transcoder resource requests that have
been denied due to throttling (a resource from this transcoder was not
allocated because, as specified by the Cisco CallManager service parameter MTP
and Transcoder Resource Throttling Percentage, the transcoder was being
utilized beyond the configured throttle percentage). This counter increments
each time a resource is requested from this transcoder and is denied due to
throttling. This counter reflects a running total since the transcoder device
registered with the Cisco CallManager service.
|