Cisco UCS Manager GUI Configuration Guide, Release 2.0
Recovering a Lost Password
Downloads: This chapterpdf (PDF - 490.0KB) The complete bookPDF (PDF - 9.68MB) | The complete bookePub (ePub - 1.45MB) | Feedback

Recovering a Lost Password

Recovering a Lost Password

This chapter includes the following sections:

Recovering a Lost Password

Password Recovery for the Admin Account

The admin account is the system administrator or superuser account. If an administrator loses the password to this account, you can have a serious security issue. As a result, the procedure to recover the password for the admin account requires you to power cycle all fabric interconnects in a Cisco UCS domain.

When you recover the password for the admin account, you actually change the password for that account. You cannot retrieve the original password for that account.

You can reset the password for all other local accounts through Cisco UCS Manager. However, you must log in to Cisco UCS Manager with an account that includes aaa or admin privileges.


Caution


This procedure requires you to power down all fabric interconnects in a Cisco UCS domain. As a result, all data transmission in the Cisco UCS domain is stopped until you restart the fabric interconnects.


Determining the Leadership Role of a Fabric Interconnect

Procedure
    Step 1   In the Navigation pane, click the Equipment tab.
    Step 2   In the Equipment tab, expand Equipment > Fabric Interconnects.
    Step 3   Click the fabric interconnect for which you want to identify the role.
    Step 4   In the Work pane, click the General tab.
    Step 5   In the General tab, click the down arrows on the High Availability Details bar to expand that area.
    Step 6   View the Leadership field to determine whether the fabric interconnect is the primary or subordinate.

    Verifying the Firmware Versions on a Fabric Interconnect

    You can use the following procedure to verify the firmware versions on all fabric interconnects in a Cisco UCS domain. You can verify the firmware for a single fabric interconnect through the Installed Firmware tab for that fabric interconnect.

    Procedure
      Step 1   In the Navigation pane, click the Equipment tab.
      Step 2   In the Equipment tab, click the Equipment node.
      Step 3   In the Work pane, click the Firmware Management tab.
      Step 4   In the Installed Firmware tab, verify that the following firmware versions for each fabric interconnect match the version to which you updated the firmware:
      • Kernel version
      • System version

      Recovering the Admin Account Password in a Standalone Configuration

      This procedure will help you to recover the password that you set for the admin account when you performed an initial system setup on the fabric interconnect. The admin account is the system administrator or superuser account.

      Before You Begin
      1. Physically connect the console port on the fabric interconnect to a computer terminal or console server
      2. Determine the running versions of the following firmware:
        • The firmware kernel version on the fabric interconnect
        • The firmware system version

      Tip


      To find this information, you can log in with any user account on the Cisco UCS domain.


      Procedure
        Step 1   Connect to the console port.
        Step 2   Power cycle the fabric interconnect:
        1. Turn off the power to the fabric interconnect.
        2. Turn on the power to the fabric interconnect.
        Step 3   In the console, press one of the following key combinations as it boots to get the loader prompt:
        • Ctrl+l
        • Ctrl+Shift+r

        You may need to press the selected key combination multiple times before your screen displays the loader prompt.

        Step 4   Boot the kernel firmware version on the fabric interconnect.
        loader > 
        boot /installables/switch/
        kernel_firmware_version
        
        


        Example:
        loader > 
        boot /installables/switch/ucs-6100-k9-kickstart.4.1.3.N2.1.0.11.gbin
        
        Step 5   Enter config terminal mode.
        Fabric(boot)# 
        config terminal
        
        
        Step 6   Reset the admin password.
        Fabric(boot)(config)# 
        admin-password
        password
        
        

        Choose a strong password that includes at least one capital letter and one number. The password cannot be blank.

        The new password displays in clear text mode.

        Step 7   Exit config terminal mode and return to the boot prompt.
        Step 8   Boot the system firmware version on the fabric interconnect.
        Fabric(boot)# 
        load /installables/switch/
        system_firmware_version
        
        


        Example:
        Fabric(boot)# 
        load /installables/switch/ucs-6100-k9-system.4.1.3.N2.1.0.211.bin
        
        Step 9   After the system image loads, log in to Cisco UCS Manager.

        Recovering the Admin Account Password in a Cluster Configuration

        This procedure will help you to recover the password that you set for the admin account when you performed an initial system setup on the fabric interconnects. The admin account is the system administrator or superuser account.

        Before You Begin
        1. Physically connect a console port on one of the fabric interconnects to a computer terminal or console server
        2. Obtain the following information:
          • The firmware kernel version on the fabric interconnect
          • The firmware system version
          • Which fabric interconnect has the primary leadership role and which is the subordinate

        Tip


        To find this information, you can log in with any user account on the Cisco UCS domain.


        Procedure
          Step 1   Connect to the console port.
          Step 2   For the subordinate fabric interconnect:
          1. Turn off the power to the fabric interconnect.
          2. Turn on the power to the fabric interconnect.
          3. In the console, press one of the following key combinations as it boots to get the loader prompt:
            • Ctrl+l
            • Ctrl+Shift+r

            You may need to press the selected key combination multiple times before your screen displays the loader prompt.

          Step 3   Power cycle the primary fabric interconnect:
          1. Turn off the power to the fabric interconnect.
          2. Turn on the power to the fabric interconnect.
          Step 4   In the console, press one of the following key combinations as it boots to get the loader prompt:
          • Ctrl+l
          • Ctrl+Shift+r

          You may need to press the selected key combination multiple times before your screen displays the loader prompt.

          Step 5   Boot the kernel firmware version on the primary fabric interconnect.
          loader > boot /installables/switch/
          kernel_firmware_version
          


          Example:
          loader > boot /installables/switch/ucs-6100-k9-kickstart.4.1.3.N2.1.0.11.gbin
          
          Step 6   Enter config terminal mode.
          Fabric(boot)# config terminal
          
          Step 7   Reset the admin password.
          Fabric(boot)(config)# admin-password password
          

          Choose a strong password that includes at least one capital letter and one number. The password cannot be blank.

          The new password displays in clear text mode.

          Step 8   Exit config terminal mode and return to the boot prompt.
          Step 9   Boot the system firmware version on the primary fabric interconnect.
          Fabric(boot)# load /installables/switch/
          system_firmware_version
          


          Example:
          Fabric(boot)# load /installables/switch/ucs-6100-k9-system.4.1.3.N2.1.0.211.bin
          
          Step 10   After the system image loads, log in to Cisco UCS Manager.
          Step 11   In the console for the subordinate fabric interconnect, do the following to bring it up:
          1. Boot the kernel firmware version on the subordinate fabric interconnect.
            loader > boot /installables/switch/
            kernel_firmware_version
            
          2. Boot the system firmware version on the subordinate fabric interconnect.
            Fabric(boot)# load /installables/switch/
            system_firmware_version