MGX and SES Error Messages, Release 4
MGX and SES Error Messages, Release 4.0.10 (part D)
Downloads: This chapterpdf (PDF - 683.0KB) The complete bookPDF (PDF - 18.8MB) | Feedback

Error Messages for Release 4.0.10

Table Of Contents

Error Messages for Release 4.0.10

DDTS: "drivers"

MESSAGE: DRV_EVENT

MESSAGE: DDLXIFDEV_CRDMP_EVENT

MESSAGE: DDLSCHEDDEV_CRDMP_EVENT

MESSAGE: DDLQUEUEDEV_CRDMP_EVENT

MESSAGE: DDLPORTDEV_CRDMP_EVENT

MESSAGE: DDLPIFDEV_CRDMP_EVENT

MESSAGE: DDLFRAMER_CRDMP_EVENT

DDTS "config-upload"

MESSAGE: CUT_RAM_FILE

MESSAGE: CUT_RAM_NAME

MESSAGE: CUT_RAM_LOG

DDTS: "shm"

MESSAGE: CBC_HMM_ERR

DDTS: "control-point"

MESSAGE: SEMCREATE_FAILED

MESSAGE: SEMTAKE_FAILED

MESSAGE: SEMGIVE_FAILED

MESSAGE: SEMTAKE_TASK

MESSAGE: SEMTAKE_RECOVER

DDTS: "pxm-connmgm"

MESSAGE: RAMSYNCEV

DDTS: "pxm-connmgm"

MESSAGE: CNF_MISMATCH

MESSAGE: INFO_LOG

DDTS: "drivers"

MESSAGE: GENERROR

MESSAGE: A2SARSNDERROR

MESSAGE: INVMAGIC

DDTS: "shm"

MESSAGE: CD_INFO

MESSAGE: MIB_MISMATCH

MESSAGE: CD_NOT_READY

MESSAGE: MAKE_HSB_ACTIVE_FAILED

DDTS: "atmsig"

MESSAGE: FAILHALFLEGREM

DDTS: "control-point"

MESSAGE: FM_OPEN_FAIL

DDTS: "pnnisys"

MESSAGE: CCB_INVALID_VALUE

DDTS: "drivers"

MESSAGE: SAR_PURGE_QUEUES

MESSAGE: GEN_INFO

MESSAGE: ALARM_SET

MESSAGE: ALARM_CLR

MESSAGE: ALARM_ERROR

MESSAGE: SAR_HDR_ERR

MESSAGE: SAR_QUE_CORRUPT

MESSAGE: SAR_OVFLW_START

MESSAGE: SAR_OVFLW_END

MESSAGE: SAR_INJFRZN_ERR

MESSAGE: SAR_RESET_QE

DDTS: "atmsig"

MESSAGE: FAILHALFLEGREM

DDTS: "snmp-ma"

MESSAGE: NOENTITYFOUND

DDTS: "control-point/pxm-connmgm"

MESSAGE: FOPEN_FAILED

MESSAGE: FREAD_FAILED

MESSAGE: FWRITE_FAILED

DDTS: "axsme_apps"

MESSAGE: EM_ERROR

DDTS: "atmsig"

MESSAGE: DISABLE_PORT

DDTS: "shm"

MESSAGE: PXM_PATH_FAIL

MESSAGE: DBG_FILE_WR

MESSAGE: DBG_FILE_ERR

MESSAGE: DBG_DIR_ERR

DDTS: "pxm-connmgm"

MESSAGE: SYNCRAMERR

MESSAGE: SYNCRAMEV

DDTS: "hw-poll"

MESSAGE: INV_DEVICE_PTR

MESSAGE: CORRUPT_POLL_Q

MESSAGE: DISK_PARMS_CHG

MESSAGE: DISK_SPIN_OK

MESSAGE: DISK_SPIN_NOK

MESSAGE: DISK_SPIN_STATS

MESSAGE: DISK_SPIN_ERR

MESSAGE: DISK_TMR_ERR

MESSAGE: BRAM_ENBL_FAIL

DDTS: "sctfm"

MESSAGE:DIRECTORY_DELETE

MESSAGE: SYNCRAMERR

DDTS : pxm-connmgm

MESSAGE: RAMSYNCEV

MESSAGE: CREF_NOT_FOUND

MESSAGE: PARTN_BW_EXCEED

MESSAGE: VI_BW_EXCEED

MESSAGE: SLOT_BW_EXCEED

MESSAGE: BW_CAC_FAIL

MESSAGE: RSRC_ALLOC_FAIL

MESSAGE: CREF_LIMIT:_REACHED

MESSAGE: LCN_LIMIT:_REACHED

MESSAGE: INTF_CFG_ERR

MESSAGE: PART_CFG_ERR

MESSAGE: IF_PLCY_CFG_ERR

MESSAGE: VPI_VCI_RANGE_ERR

DDTS: "snmp-ma"

MESSAGE: SEM

DDTS: "CLI"

MESSAGE: SCM_PARMS_CNF

DDTS: "config-upload"

MESSAGE: CUTS_DIR_FOUND

MESSAGE: CUTS_NON_DIR_FILE_FOUND

MESSAGE: CUTS_IOCTL_FAILED

MESSAGE: CUTS_OPEN_FAILED

MESSAGE: CUTS_MKDIR_FAILED

MESSAGE: ACK_TIMEOUT

MESSAGE: CUTS_EPID

MESSAGE: CUTS_TIMER_CREATE

MESSAGE: CUTS_ATTHDLR

MESSAGE: CUTS_TMR_SCHD

MESSAGE: CUTS_TMR_CNCL

MESSAGE: CUTS_IPC_FREE_ERR

MESSAGE: IPCFAIL

MESSAGE: IPC_ALLC_FAILED

MESSAGE: CUTS_INVALID_RQ

MESSAGE: CUTS_INVLD_RQSTATE

MESSAGE: CUTS_WRKR_UPDAT

MESSAGE: TMR_ERROR

MESSAGE: RNWY_TASK

MESSAGE: BAD_RSPNSE

MESSAGE: CUTS_FC_FAILED

MESSAGE: BAD_FILEINDX

MESSAGE: FILE_STATE_GENERATING

MESSAGE: CUTS_CHILD_ACTIVE

MESSAGE: CUTS_EPID_RESPONSE

MESSAGE: CUTS_FC_DONE

MESSAGE: CUTS_TRAP_NOTASK

MESSAGE: CUTS_TRAP_START

MESSAGE: CUTS_TRAP_FAIL

MESSAGE: CUTS_TRAP_DONE

MESSAGE: CUTS_TRAP_ABRT

MESSAGE: CUTS_UPDT_DONE

MESSAGE: SEND_CUTV_FAIL

MESSAGE: UPD_FCB_FAIL

MESSAGE: TMR_REINIT_FAIL

MESSAGE: SEMGIVE_FAIL

MESSAGE: CUTS_FILE_MUTEX

MESSAGE: TXID_GET_FAILED

MESSAGE: INV_TXID

MESSAGE: CANNOT_PROCEED

MESSAGE: TRAP_SEND_FAIL

MESSAGE: CUTS_UPDT_FAIL

MESSAGE: RMTCLOSE_FAIL

DDTS: "signaling"

MESSAGE: CC_AUD_REL

DDTS: "clocking"

MESSAGE: CLK_IPC_FAIL

MESSAGE: EPID_RESOLVE_FAILED

MESSAGE: TIMER_SCHEDULE_FAIL

MESSAGE: TIMER_CANCEL_FAIL

DDTS: "rpm"

MESSAGE: DB_ALLOC_ERR

DDTS: "shm"

MESSAGE: BC_HLTH_UPDATE

DDTS: "config-upload"

MESSAGE: CUTW_EPID

MESSAGE: CUTW_TIMER_CREATE

MESSAGE: CUTW_ATTHDLR

MESSAGE: CUTW_TMR_SCHD

MESSAGE: CUTW_TMR_CNCL

MESSAGE: CUTW_IPC_FREE_ERR

MESSAGE: IPCFAIL

MESSAGE: IPC_ALLC_FAILED

MESSAGE: CUTW_INVALID_RQ

MESSAGE: CUTW_EPID_RESOLVE

MESSAGE: CUTW_WRKR_UPDAT

MESSAGE: CUTW_INIT_PTR

MESSAGE: CUTW_FC_FAILED

MESSAGE: BAD_FILEINDX

MESSAGE: CUTWFILENAME

MESSAGE: W_RATEVENTPENDING

MESSAGE: NULL_FILEP

MESSAGE: TASK_STATUS_TRANS

MESSAGE: SEMTAKE_FAIL

MESSAGE: SEMGIVE_FAIL

MESSAGE: NULL_PTR

MESSAGE: MEM_FAIL

MESSAGE: MEMDEALL_FAIL

MESSAGE: RTOID_FAIL

MESSAGE: TBLOID_FAIL

MESSAGE: CNFOID_FAIL

MESSAGE: CNFVRBND_FAIL

MESSAGE: FINDOBJ_FAIL

MESSAGE: GTNXT_FAIL

MESSAGE: WRITE_FAIL

MESSAGE: GET_FAIL

MESSAGE: GETNEXT_FAIL

MESSAGE: GETSCLR_FAIL

MESSAGE: IOCTL_FAIL

MESSAGE: CR_RESULT

MESSAGE: FILE_ERR

MESSAGE: WRITE_BYTESFAIL

MESSAGE: MAX_ROWS_EXCEEDED

MESSAGE: INVALID_PARAM

MESSAGE: TXID_GET_FAILED

MESSAGE: TIME_GET_FAILED

MESSAGE: OPEN_FAILED

MESSAGE: FNAME_PARSE_ERROR

MESSAGE: BITMAP_FAILURE

MESSAGE: NULL_ERRHDLR

MESSAGE: FILE_READFAIL

MESSAGE: REMOVE_FAIL

MESSAGE: VLDN_THRESH_EXCEED

MESSAGE: RMT_FILE_IOCTL_FAIL

MESSAGE: LATEST_STATIC_FAIL

MESSAGE: INVALID_REQ

MESSAGE: REQ_PROC_INVALID

MESSAGE: INVALID_PROC_PARTS

MESSAGE: INVALID_SLOT

MESSAGE: SEEK_UPDATE_FAIL

MESSAGE: REPLICATE_FAIL

MESSAGE: INVALID_REQ_TXID

MESSAGE: TXID_AUDIT_FAILED

MESSAGE: CHKSUM_FAILURE

MESSAGE: MEM_ALLOC_FAIL

MESSAGE: ALARM_BUFF_FAIL

MESSAGE: STBY_REMOVE_FAIL

MESSAGE: STATIC_DEL_FAIL

MESSAGE: DIR_CHECK_FAIL

MESSAGE: ADDINT_FAILURE

MESSAGE: SANITY_FAILURE

DDTS: "diskdb"

MESSAGE: DBCLNT_INFO

DDTS: "shm"

MESSAGE: NFATAL_MAJ_ERPT3

MESSAGE: FRUMISMATCH_RPT

MESSAGE: BC_HLTH_UPDATE

MESSAGE: IP_NOT_CONFIGURED

MESSAGE: GEN_ERROR

MESSAGE: EPID_CREATE_ERR

MESSAGE: SFM_SEND_ERR

MESSAGE: INTERCD_APS_RPT

DDTS:"ssi"

MESSAGE: HANGTASK_MSEC

MESSAGE: ATADRVERR

MESSAGE: ATAWAITERR

MESSAGE: ATADRVINFO

MESSAGE: HNGNOSTKTRC

DDTS: "shm"

MESSAGE: FUNC_FAILED

MESSAGE: SRM_UNAVAIL

MESSAGE: MAKE_HSB_ACTIVE_FAILED

MESSAGE: SEC_CD_INFO

MESSAGE: AC_TIME_OUT_ERR

MESSAGE: AC_DWNLBRAMERR

MESSAGE: AC_UPLDBRAMERR

MESSAGE: DUPLICATE_CONNID_EXISTS

DDTS: "diskdb"

MESSAGE: RESV_NO_DB

MESSAGE: NO_PSEU_NO_RESV

MESSAGE:DETECT_UNDESIRE

MESSAGE: PSEUDO_ONLY

MESSAGE: DBSVR_TRAPWARNING

DDTS: "diskdb"

MESSAGE: DBSYNC_INFO

DDTS: "ssi"

MESSAGE: MBLKBUFFREEFAIL

MESSAGE: MBLKFREEFAIL

DDTS: "snmp-ma"

MESSAGE: EPIDWARN

MESSAGE: EPIDERROR

DDTS: "ctc"

MESSAGE: RATERR030

MESSAGE: RATERR031

MESSAGE: RATERR054

MESSAGE: RATERR056

MESSAGE: RATERR057

MESSAGE: RATERR058

MESSAGE: RATERR059

MESSAGE: RATERR060

MESSAGE: RATERR061

MESSAGE: RATERR062

MESSAGE: RATERR063

MESSAGE: RATERR084

DDTS: "axsm_apps"

MESSAGE: APS_ERROR

DDTS: "ssi"

MESSAGE: BELOWTHRES

MESSAGE: NOPARTITION

MESSAGE: DOWNSTATIC

MESSAGE: DOWNVXWORKS

MESSAGE: ERRBUFFCORR

MESSAGE: HANGTHRESH

DDTS: "shm"

MESSAGE: SCM_PARMS_CHG

MESSAGE: MCAST_VER_CHG1

MESSAGE: MCAST_VER_CHG2

MESSAGE: MASTERSHIP_REL

MESSAGE: BC_INFO_FIXED

MESSAGE: BC_BMAP_INV

MESSAGE: BC_INFO_IGNORED

MESSAGE: BC_HLTH_CHNGED

MESSAGE: MC_VER_CHG

MESSAGE: API_CALL_ERR

MESSAGE: XBAR_NOT_UP

MESSAGE: HV_PORT_INVALID

MESSAGE: MASTERSHIP_OK

MESSAGE: HW_LOG_TRAP_ERR


Error Messages for Release 4.0.10


The following error messages were added for Release 4.0.10.

DDTS: "drivers"

MESSAGE: DRV_EVENT

SEVERITY: Information
FORMAT: "DDL_EVENT: %s\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "Device Driver Layer Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLXIFDEV_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLXIFDEV_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLXIFDEV Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLSCHEDDEV_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLSCHEDDEV_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLSCHEDDEV Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLQUEUEDEV_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLQUEUEDEV_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLQUEUEDEV Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors - this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLPORTDEV_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLPORTDEV_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLPORTDEV Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLPIFDEV_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLPIFDEV_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLPIFDEV Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DDLFRAMER_CRDMP_EVENT

SEVERITY: Information
FORMAT: "DDLFRAMER_CRDMP_EVENT: %s 0x%x 0x%x\n"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "DDLFRAMER Core Dump Event
- more info can be obtained from the error string printed out
- applications calling the drivers would log appropriate errors
- this is to get detailed info on the specific error experienced by the driver"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS "config-upload"

MESSAGE: CUT_RAM_FILE

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cutram) Ftp Request for File:%s Physical Slot Number Failed."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Unable to determine the Physical Slot Number for the file."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUT_RAM_NAME

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x) (cutram) Ftp Request for File:%s Ram disk name Failed."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Unable to determine the Ram disk name for the file."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUT_RAM_LOG

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x) (cutram) Ftp Request for File:%s Logical Slot:%d Phy Slot Conv Failed."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Unable to convert the Logical Slot to a Physical Slot Number."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "shm"

MESSAGE: CBC_HMM_ERR

SEVERITY: Error
FORMAT: "%s cbc_num = %d,%d,%d,%d : %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "CBC HMM Event."
RECOMMENDED Action: Please capture the following information and call your Cisco technical support representative:
REQUIRED_INFO: " On PXM:
1. dspcds
2. dsplog -sl <slot that experienced the error>
3. dsplog -sl <other pxm slot>
4. dsperr for slots specified above.
5. dspcbclk "

DDTS: "control-point"

MESSAGE: SEMCREATE_FAILED

SEVERITY: Warning
FORMAT: "%d: errno 0x%x Semaphore create failed for %s."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Can not create semaphore that is required to protect MIB functions"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMTAKE_FAILED

SEVERITY: Warning
FORMAT: "%d: errno 0x%x Semaphore take failed for %s."
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Can not take semaphore that is required to protect MIB functions"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMGIVE_FAILED

SEVERITY: Warning
FORMAT: "%d: errno 0x%x Semaphore give failed for %s."
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Can not release semaphore which required to protect MIB functions"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMTAKE_TASK

SEVERITY: Warning
FORMAT: "%d: errno 0x%x Semaphore was taken by taskId 0x%x, taskName %s."
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Cannot take semaphore because another task has it"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMTAKE_RECOVER

SEVERITY: Warning
FORMAT: "%s_%d: Could not recover Semaphore from Task Id %x, Task Name %s."
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "A time out has occured and the previous task still has the semaphore"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "pxm-connmgm"

MESSAGE: RAMSYNCEV

SEVERITY: Warning
FORMAT: "Line %d: Ram Sync %s error - errno = 0x%x, resetCause = %d"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "Ram sync related problems/errors"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

DDTS: "pxm-connmgm"

MESSAGE: CNF_MISMATCH

SEVERITY: Major Alert
FORMAT: "Slot %d, PS card %d Line %d : %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Config mismatch between SHM and Autocard"
RECOMMENDED ACTION: "Collect information specified in REQUIRED_INFO: field and call TAC"
REQUIRED_INFO: "Collect dsplog, dsperr information"

MESSAGE: INFO_LOG

SEVERITY: Information
FORMAT: "Info Log %s Slot %d Data %d line %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Informational Log"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "drivers"

MESSAGE: GENERROR

SEVERITY: Warning
FORMAT: "Gen Error : %s: errno = 0x%x Args : %d %d %d %d"
FLAG: No Flag
LIMIT: Four Hours
EXPLANATION: "Event logs for general errors in Rx direction"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: A2SARSNDERROR

SEVERITY: Warning
FORMAT: "P1 SAR send error: status %x, errno %x"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "This means the atmizerSarFrameSend has failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: "Capture the following
a. SarShowQPtrs from shellconn
b. SarShow from shellconn
If status in the event log is 4, please capture SarLcnShow <errno>"

MESSAGE: INVMAGIC

SEVERITY: Error
FORMAT: "QE#%d InvCnt=%d Sts=0x%x #Frms=%d HCnt=%d SCnt=%d Flgs=0x%x InQ=%d CPUdump=%s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The special magic field in the given message header is not a valid one. This indicates that QE cannot transmit the SAR messages in a specified interval. The retransmission will be started. The following are displayed:
a) InvCnt - count of invalid magic condition.
b) Sts - value of QE status register.
c) #Frms - number of frames in QE xmt queue.
d) HCnt - Hang counter of QE sar task.
e) SCnt - Starvation counter of QE sar task.
f) Flgs - QE scheduler flag.
g) InQ - 1 if frm already in queue, 0 if not
h) CPU dump - index of CPU dump if one taken. "
RECOMMENDED ACTION: No action required
REQUIRED_INFO: " a) dsplog -mod SAR on PXM
b) dsplog -mod SAR2 on PXM
c) sarQe1210CpuDumpHelp from shellconn
d) sarQe1210ShowCpuDump from shellconn
e) sarQe1210DisplayCpuDump from shellconn
f) sarQe1210StatsShow 0 from shellconn
g) sarQe1210StatsShow 1 from shellconn "

DDTS: "shm"

MESSAGE: CD_INFO

SEVERITY: Information
FORMAT: "Slot %d ,%s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "HSB info for the specific slot"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: MIB_MISMATCH

SEVERITY: Warning
FORMAT: "Prislot %d Mib ver %d, SecSlot %d Mib ver %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "HSB MIB version mismatch between pri and sec slot"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: CD_NOT_READY

SEVERITY: Warning
FORMAT: "Slot %d, not ready to go Active"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Slot is not hotstandby yet so cannot go active"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: MAKE_HSB_ACTIVE_FAILED

SEVERITY: Warning
FORMAT: "%s, Slot %d, Redundant slot %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Error in making HSB go Active"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

DDTS: "atmsig"

MESSAGE: FAILHALFLEGREM

SEVERITY: Notice
FORMAT: "halfLeg removal failed, %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to remove endpoint connection resources."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: On PXM cli the output of the following commands dspver, dspcds, dspdate, dsppnports, dspsigstats, dsppncons, dsppnctlvc, dsplog, dspmempart can be sent to the Cisco Customer support.

DDTS: "control-point"

MESSAGE: FM_OPEN_FAIL

SEVERITY: Error
FORMAT: "%s: slotNum: %d, reqType : %d, Msg: %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Open API of the specified file failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please collect the output of CLIs: dspver, dspcds, dsplog

DDTS: "pnnisys"

MESSAGE: CCB_INVALID_VALUE

SEVERITY: Error
FORMAT: "%s= %d - %s"
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Detect module-id value goes beyond the MODULE_MAX "
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: On PXM cli the output of the following commands dspver, dspcds, dspdate, dsppnports, dspsigstats, dsppncons, dsppnctlvc, dsplog, dspmempart can be sent to the Cisco Customer support.

DDTS: "drivers"

MESSAGE: SAR_PURGE_QUEUES

SEVERITY: Error
FORMAT: "QE1210 Purge Frm & Notify Q. QE: %d Reason: %s "
FLAG: Stack Trace
LIMIT: No Throttling
EXPLANATION: "QE1210 Notify Q may be out of sync. with frames in SAR Mbin
In this case, Rx Fifo, Notify Q and SAR Mbin queues must be purged"
RECOMMENDED ACTION: "if QE1210 out of sync. can not be resolved by purging the queues, then card reset need to be done"
REQUIRED_INFO: "Pls goto shell of the controller cards and collect the infor. using shell command -- sarQe1210IsrShow 0"

MESSAGE: GEN_INFO

SEVERITY: Information
FORMAT: "%s() failed: errno:0x%x, callerPC:0x%x"
FLAG: No Flag
LIMIT: One Minute
EXPLANATION: "Logging gen info"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: ALARM_SET

SEVERITY: Major Alert
FORMAT: "SAR Alarm Set: %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This log event indicates a SAR alarm has occurred."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: " a) dspsaralms on PXM to determine slot
b) dspsaralms <almType> <slot> on PXM
c) dspsaralms <almType> <slot> <almId> on PXM
d) sarQe1210StatsShow 0 from shellconn
e) sarQe1210StatsShow 1 from shellconn "

MESSAGE: ALARM_CLR

SEVERITY: Minor Alert
FORMAT: "SAR Alarm Clr: %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This log event indicates a SAR alarm has cleared."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: " a) dspsaralms on PXM to determine slot
b) dspsaralms <almType> <slot> on PXM
c) dspsaralms <almType> <slot> <almId> on PXM
d) sarQe1210StatsShow 0 from shellconn
e) sarQe1210StatsShow 1 from shellconn "

MESSAGE: ALARM_ERROR

SEVERITY: Error
FORMAT: "SAR Alarm Error: %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This log event indicates an error occurred in SAR alarm processing."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: " a) dsplog -mod SAR on PXM
b) dspsaralms on PXM to determine slot
c) dspsaralms <almType> <slot> on PXM
d) dspsaralms <almType> <slot> <almId> on PXM
e) sarQe1210StatsShow 0 from shellconn
f) sarQe1210StatsShow 1 from shellconn "

MESSAGE: SAR_HDR_ERR

SEVERITY: Error
FORMAT: "SAR HDR Err. line: %d QE: %d hdrPtr: %x bufPtr: %x offset: %d len: %d glcn: %x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "QE1210 INJ frozen. Card reset needed for recovery"
RECOMMENDED ACTION: "The card will be reset if QE1210 INJ frozen is more than 20 seconds. After the cared is reset, we should check the log. Msg."
REQUIRED_INFO: "This should not continuously happen. if the pxm45 resets continuously, collect dsplog, dsperr, dspver, etc and call TAC"

MESSAGE: SAR_QUE_CORRUPT

SEVERITY: Error
FORMAT: "SAR Rx Queue Corruped. line: %d QE: %d rdPtr: %x wrPtr: %x nextPtr: %x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This log. event indicates that SAR Rx Queue
is corrupted."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: "dsplog -mod SAR on both active and stdby pxm cards."

MESSAGE: SAR_OVFLW_START

SEVERITY: Warning
FORMAT: "SAR overflow start in QE: %d Idle2OvflwCnt: %d"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "SAR overflow has occurred in QE. The overflow will be detected and be shut down if this overflow lasts for more than 15 seconds (i.e. sustaining overflow)"
RECOMMENDED ACTION: "reenable the disabled SAR conn which caused the SAR overflow, if needed."
REQUIRED_INFO: " a) dsplog -mod SAR2 on PXM
b) dspsaralms on PXM to determine slot
c) dspsaralms <almType> <slot> on PXM
d) dspsaralms <almType> <slot> <almId> on PXM
e) sarQe1210StatsShow 0 from shellconn
f) sarQe1210StatsShow 1 from shellconn "

MESSAGE: SAR_OVFLW_END

SEVERITY: Warning
FORMAT: "SAR overflow end in QE: %d dsbGlcnFrm#: %d ovflwType: %s"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "SAR overflow has occurred in QE. The overflow will be detected and be shut down if this overflow lasts for more than 15 seconds (i.e. sustaining overflow)"
RECOMMENDED ACTION: "reenable the disabled SAR conn which caused the SAR overflow, if needed."
REQUIRED_INFO: " a) dsplog -mod SAR2 on PXM
b) dspsaralms on PXM to determine slot
c) dspsaralms <almType> <slot> on PXM
d) dspsaralms <almType> <slot> <almId> on PXM
e) sarQe1210StatsShow 0 from shellconn
f) sarQe1210StatsShow 1 from shellconn "

MESSAGE: SAR_INJFRZN_ERR

SEVERITY: Error
FORMAT: "ln: %d QE: %d Sts3: %x tName: %s Hed1: %x Hed2: %x DmaSrc: %x DmaLen: %x pyldLen: %x hold: %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "QE1210 INJ frozen. Card reset needed for recovery"
RECOMMENDED ACTION: "The card will be reset if QE1210 INJ frozen is more than 20 seconds. After the cared is reset, we should check the log. Msg."
REQUIRED_INFO: "This should not continuously happen. if the pxm45 resets continuously, collect dsplog, dsperr, dspver, etc and call TAC"

MESSAGE: SAR_RESET_QE

SEVERITY: Error
FORMAT: "Reset QE : QE=%d, Rsn=%s, sts0=%x, sts1=%x, sts2=%x, sts3=%x, RstCnt=%d, Cnt1=%d, Cnt2=%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "When a QE fatal error such as Free List Empty occurs, we must reset QE chip. During the QE reset, all of incoming cells will be discarded. QE can be recovered after the reset."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: "Please use dsplog -mod SAR to collect the info. when this problem happens."

DDTS: "atmsig"

MESSAGE: FAILHALFLEGREM

SEVERITY: Notice
FORMAT: "halfLeg removal failed, %s"
FLAG: No Flag
LIMIT: Five Seconds
EXPLANATION: "Error in freeing up data structure"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: On PXM cli the output of the following commands dspver, dspcds, dspdate, dsppnports, dspsigstats, dsppncons, dsppnctlvc, dsplog, dspmempart can be sent to the Cisco Customer support.

DDTS: "snmp-ma"

MESSAGE: NOENTITYFOUND

SEVERITY: Information
FORMAT: "%s: No Entity found in the system. errno = 0x%x"
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "could not create entries in entPhysicalTable"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "control-point/pxm-connmgm"

MESSAGE: FOPEN_FAILED

SEVERITY: Warning
FORMAT: "%s: slotNum %d, fileType : %d, Msg: %s"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "Open API of the specified file failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: FREAD_FAILED

SEVERITY: Warning
FORMAT: "%s: fD: %d, slotNo: %d, fileType: %d, Msg: %s"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "File read failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: FWRITE_FAILED

SEVERITY: Warning
FORMAT: "%s: fD: %d, slotNo: %d, fileType: %d, Msg: %s"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "File write failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

DDTS: "axsme_apps"

MESSAGE: EM_ERROR

SEVERITY: Error
FORMAT: "EM ERROR: %s\n"
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Indicates an internal error detected by the EM application. It needs to be analyzed by TAC and possibly by the development team. In normal operation, such an error should never get reported."
RECOMMENDED ACTION: "Please capture the following information and call your Cisco technical support representative: "
REQUIRED_INFO: " On PXM45:
1. dspcd <slot that experienced the error>
2. dspred
3. dsplog -sl <slot that experienced the error>
4. dsplog -sl <other slot in the pair if redundancy is configured>
5. dsperr for slots specified above.
On Service Module:
1. dspcd
2. dsplns
3. dspports
4. dspparts
5. dspapslns (for SONET cards) "

DDTS: "atmsig"

MESSAGE: DISABLE_PORT

SEVERITY: Warning
FORMAT: "NCDP being downed on port %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "NCDP being downed on port because we could not latch on to clock signal"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "shm"

MESSAGE: PXM_PATH_FAIL

SEVERITY: Major Alert
FORMAT: "Communication Path error with Active PXM in slot: %d, %s, MaxPollRetry: %d, MaxPollMiss: %d, MonFromStby: %d"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "The Active PXM is not sending Polls, declaring the card as frozen"
RECOMMENDED ACTION: "Verify if the Old Active PXM went through a ful reset and came up fine. If it does not come up replace the PXM"
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: DBG_FILE_WR

SEVERITY: Information
FORMAT: "Saving the SCM Poll failure debug info for slot: %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Service module is not responding to the Poll Request, so collecting the path data and saving it in a file"
RECOMMENDED ACTION: No action required
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: DBG_FILE_ERR

SEVERITY: Error
FORMAT: ":%s: Failed for Poll Failure Debug File for slot: %d, errno: 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "File operation failed for the Poll failure debug file on the specified slot"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: DBG_DIR_ERR

SEVERITY: Error
FORMAT: ":%s: failed for Poll Failure Debug Directory, errno: 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "IO operation failed for Directory for storing the Poll failure debug information"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative

DDTS: "pxm-connmgm"

MESSAGE: SYNCRAMERR

SEVERITY: Major Alert
FORMAT: "%s: Sync Ram Error at line %d : errno %x"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "This error indicates a general error in sync ram area"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: SYNCRAMEV

SEVERITY: Warning
FORMAT: "Sync Ram Error at line %di, errno = 0x%x"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "This error indicates a general error in sync ram area"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

DDTS: "hw-poll"

MESSAGE: INV_DEVICE_PTR

SEVERITY: Information
FOMAT "Invalid device pointer in poll Q, device = %p, devId %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "An invalid pointer was detected in the HMM polling queue"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CORRUPT_POLL_Q

SEVERITY: Information
FORMAT: "HMM Poll Q corrupted (devId = %d, devPtr=%p): %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Corrupt HMM Poll Queue."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DISK_PARMS_CHG

SEVERITY: Information
FORMAT: "Disk Spin Parms Changed (SpinEnabled: NoAccess, SpinDown, Start Time:) From: %d, %d, %d, %d:%d:%d TO: %d, %d, %d, %d:%d:%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Disk Spin Down and Up has been done successfully"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DISK_SPIN_OK

SEVERITY: Information
FORMAT: "Disk Spin Down complete: NoAccess Time: %d, SpinDown Time: %d, Start Time: %d:%d:%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Disk Spin Down and Up has been done successfully"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DISK_SPIN_NOK

SEVERITY: Information
FORMAT: "Disk Spin Down Not complete: Time: NoAccess: %d, SpinDown: %d, Start: %d:%d:%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Disk Spin Down and Up has NOt been done successfully"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DISK_SPIN_STATS

SEVERITY: Information
FORMAT: "Disk Spin Stats: Spin Done: %d, Not Done: %d, InAct Retry(total): %d (%d), Spin Retry(total): %d(%d), Time Done: %d:%d:%d."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Disk Spin Down/Up stats collected log"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DISK_SPIN_ERR

SEVERITY: Error
FORMAT: "Disk Spin %s Failed, errno = 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The Disk Spin Down/Up failed"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: DISK_TMR_ERR

SEVERITY: Error
FORMAT: "Failed to Start the timer for Spin Down Handler, errno: %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to start the timer for spinning down/up the hard disk"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: BRAM_ENBL_FAIL

SEVERITY: Major Alert
FORMAT: "HMM:Bram write enable failed. Expected value:0x%02x Actual value:0x%02x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Write Enable for BRAM failed. This means that that the PIO controlling the writes to BRAM/ BRAM itself is not functioning properly and any further writes to BRAM will not be effective Card will go to failed state. In a redundant configuration this will cause a switchover "
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

DDTS: "sctfm"

MESSAGE:DIRECTORY_DELETE

SEVERITY: Information
FORMAT: " directory %s deleted"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "This is just for information, telling us that the specified directory has been deleted from PXM HDD"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Collect output from dsplog, dsprev before notifying TAC.

MESSAGE: SYNCRAMERR

SEVERITY: Information
FORMAT: "Sync Ram Error line %d cause %s errno %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Internal Error. Could occur under normal circumstances. Typical scenario includes reset of standby PXM while bulk/incrementa sync is in progress"
RECOMMENDED ACTION: "There may not be a need for any corrective action as the card would be reset. However please collect the following information dspscts on both active and standby PXM If you find they are different data then for further analysis and call TAC"
REQUIRED_INFO: No required info

DDTS : pxm-connmgm

MESSAGE: RAMSYNCEV

SEVERITY: Warning
FORMAT: "Line %d: PXMCM Ram Sync %s error - errno = 0x%x, resetCause = %d"
FLAG: No Flag
LIMIT: One Second
EXPLANATION: "This error is logged while updating the standby PXM, Standby card is rebooted"
RECOMMENDED ACTION: Indicates an internal error detected by the PXM connection management module. It needs to be analyzed by TAC and possibly by the development team./
REQUIRED_INFO : Please capture the following information from the PXM45 cli and call your TAC support:
1 ) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: CREF_NOT_FOUND

SEVERITY: Warning
FORMAT: "%s: ConnRef not found for lin = %d, vpi = %d, vci = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The connection endpoint does not exist for the given lin, vpi, vci"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: PARTN_BW_EXCEED

SEVERITY: Warning
FORMAT: "line %d: Partition B/W exceeded for lin %d part %d cos %d B/W1 = %d, B/W2 = %d, B/W3 = %d, B/W4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The partition b/w exceeds the required b/w for connection commit"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: VI_BW_EXCEED

SEVERITY: Warning
FORMAT: "line %d: VIs B/W exceeded for lin %d part %d cos %d B/W1 = %d, B/W2 = %d , B/W3 = %d, B/W4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The VI b/w exceeds the required b/w for connection commit"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: SLOT_BW_EXCEED

SEVERITY: Warning
FORMAT: "line %d: Slot B/W exceeded for lin %d part %d cos %d B/W = %d, Max B/W = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The slot b/w exceeds the required b/w for connection commit"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: BW_CAC_FAIL

SEVERITY: Warning
FORMAT: "line %d: Error in b/w cac for lin = %d, part =%d, cos = %d, ingr ecr =%d, egr ecr =%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Bandwidth CACing failed for the given connection endpoint"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: RSRC_ALLOC_FAIL

SEVERITY: Warning
FORMAT: "line %d: Resource Check/Alloc Failed for lin %d vpi %d vci %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Resource Allocation failed for a given connection endpoint"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: CREF_LIMIT:_REACHED

SEVERITY: Warning
FORMAT: "line %d: cref limit reached on qe %d lin %d partId %d curr %d cmtted %d max %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Cref allocation failed for the connection"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: LCN_LIMIT:_REACHED

SEVERITY: Warning
FORMAT: "line %d: LCN limit reached for lin %d part %d cos %d value1 %d value2 %d value3 %d value4 %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "LCN limit reached for the given interface"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: INTF_CFG_ERR

SEVERITY: Warning
FORMAT: "line %d: %s : lin %d arg1 = %d arg2 = %d arg3 = %d arg4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Configuration failed for the given interface"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: PART_CFG_ERR

SEVERITY: Warning
FORMAT: "line %d: %s : lin %d part %d arg1 = %d arg2 = %d arg3 = %d arg4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Configuration failed for the given partition"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: IF_PLCY_CFG_ERR

SEVERITY: Warning
FORMAT: "line %d: %s : lin %d part %d arg1 = %d arg2 = %d arg3 = %d arg4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Interface Policy configuration failed for the given partition"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

MESSAGE: VPI_VCI_RANGE_ERR

SEVERITY: Warning
FORMAT: "line %d: %s : lin %d part %d arg1 = %d arg2 = %d arg3 = %d arg4 = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Incorrect VPI/VCI range"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please capture the following information from the PXM45 cli and call your TAC support:
1) dspcds/dspcd
2) dspver
3) dsplog -sl <slot which is experiencing the problem>
4) dsplog -sl < redundant slot if configured>
5) dsperr for the above slots.
6) Save the core file if required

DDTS: "snmp-ma"

MESSAGE: SEM

SEVERITY: Warning
FORMAT: "%d: caller 0x%x, errno 0x%x, %s"
FLAG: Stack Trace
LIMIT: One Tick
EXPLANATION: "Master agent semaphore events."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "CLI"

MESSAGE: SCM_PARMS_CNF

SEVERITY: Information
FORMAT: "Attempt to change SCM Poll Parms:Max Poll Retry: %d, Max Miss Poll: %d, Mon From Stby: %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "User is changing the SCM poll parms"
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

DDTS: "config-upload"

MESSAGE: CUTS_DIR_FOUND

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) Directory %s found, No need to create"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS found directory"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_NON_DIR_FILE_FOUND

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) found a non directory entry of name %s found."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS found a non directory entry of name CUT. Please remove this file and create a directory C:/CUT instead. Otherwise, Config Upload will fail."
RECOMMENDED ACTION: Make sure the C:/CUT is a directory and not a file name. If it is a file name, remove the file and create C:/CUT directory. If the card is active, try to copy a file into that C:/CUT directory. If the operation is not sucessfull, contact TAC.
REQUIRED_INFO: If CLI available, capture the following command output before contact TAC:
1) dir "C:"
2) dspversion
3) dspdate
4) dsplog -mod CUTS

MESSAGE: CUTS_IOCTL_FAILED

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) Can not get stats for %s "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Scheduler task is not able to determine whether C:/CUT is a directory or a file. Config Upload will fail if C:/CUT directory does not exist. "
RECOMMENDED ACTION: Make sure the C:/CUT is a directory and not a file name. If it is a file name, remove the file and create C:/CUT directory. If the card is active, try to copy a file into that C:/CUT directory. If the operation is not sucessfull, contact TAC.
REQUIRED_INFO: If CLI available, capture the following command output before contact TAC:
1) dir "C:"
2) dspversion
3) dspdate
4) dsplog -mod CUTS

MESSAGE: CUTS_OPEN_FAILED

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) unable to open dir/file %s "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Scheduler task is not able to open C: drive. This cause C:/CUT directory not being able to create. Config Upload will fail."
RECOMMENDED ACTION: Make sure the C:/CUT is a directory and not a file name. If it is a file name, remove the file and create C:/CUT directory. If the card is active, try to copy a file into that C:/CUT directory. If the operation is not sucessfull, contact TAC.
REQUIRED_INFO: If CLI available, capture the following command output before contact TAC:
1) dir "C:"
2) dspversion
3) dspdate
4) dsplog -mod CUTS

MESSAGE: CUTS_MKDIR_FAILED

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) unable to create directory %s "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Scheduler Task is unable to create a directory. Config Upload will fail if C:/CUT directory does not exist. "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info
TAC_DETAILS: No TAC Details

MESSAGE: ACK_TIMEOUT

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) ACK timeout, task status=\"%s\", index=%d, file type=%d, threshold=%d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Scheduler task timeout while waiting acknowlegdemeent from worker task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_EPID

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) Creation of CUTS EPID \"%s\" failed rc = 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to create epid for cuts. This might result in Config Upload not able to function correctly."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTS_TIMER_CREATE

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) Creation of timer failed rc= 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Timer Creation failed. This might result in Config Upload not able to function correctly."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO : If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplo

MESSAGE: CUTS_ATTHDLR

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) Attaching of handler \"%s\" failed Epid = 0x%08X rc= 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Attaching of handler to a cuts epid has failed. The epid name, number and error code are listed. This might result in Config Upload not able to function correctly"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTS_TMR_SCHD

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) failed to schedule timer in \"%s\" timeout value = %d, timer type = %d, rc= 0x0%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to schedule timeout. This might cause a request for Config Upload to be drop."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TMR_CNCL

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) failed to cancel timer in \"%s\" timer type = %d, rc= 0x0%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to cancel timer"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info
TAC_DETAILS: No TAC Details

MESSAGE: CUTS_IPC_FREE_ERR

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) IPC Message Free Failed : rc = 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Error in Freeing IPC message. Potential memory leak."
RECOMMENDED ACTION: If this event shows up exessively(about 5 or more times) in the event log, please log a bug and contact TAC immediatly. This is a potentential memory leak.
REQUIRED_INFO: If CLI available, capture the following command output before contacting TAC:
1) dspversion
2) dspdate
3) dspmempart 2 1
4) dsplog -mod CUTS
5) dsplog -mod CUTWRKR

MESSAGE: IPCFAIL

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) IPC SEND FAILED TO \"%s\" from \"%s\" request:%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "IPC send failed. This will result in Config Upload file creation request being dropped."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: IPC_ALLC_FAILED

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) failed to allocate ipc buffer in \"%s\"."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to allocate ipc buffer. This will result in Config Upload file creation request being dropped."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_INVALID_RQ

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) Invalid request received by cuts from system epid: req = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Invalid request received by Scheduler task(CUTS)"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_INVLD_RQSTATE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) Request received by cuts while in invalid state, rq ignored: state = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Request sent to cuts while cuts in invalid state"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_WRKR_UPDAT

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) failed to update the worker task of index (%d) to state %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS unable to update worker task state. This might cause the death of the worker task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TMR_ERROR

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) failed to find a worker for expired timerID = %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS timer expired with no associated worker task found"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RNWY_TASK

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts)found a worker task(%d)\"%s\" RUNNING yet not working on any file"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS timer expired, found a task in running with no work"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BAD_RSPNSE

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) invalid epid in an epid response or child active message from 0x%08X."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTS received a bad epid_response or child active msg"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_FC_FAILED

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) failed to process file creation request: %s for file 0x%08X."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts failed to service file creation request"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BAD_FILEINDX

SEVERITY: Error
FORMAT: "(L %d:errno 0x%x)(cuts) Invalid File index found in \"%s\" file Index = %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts found an invalid file index. This might cause Config Upload file creation to fail. "
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: FILE_STATE_GENERATING

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts)request made to generate an already generating file ignored:fileIndex = %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts got a request to generate a file already being generated"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_CHILD_ACTIVE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) rcvd a child active message from taskid: %d, taskname:%s."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts got a child active message from a task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_EPID_RESPONSE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) %s task is registered with Scheduler task as taskid: %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts got an EPID response message from a task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_FC_DONE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) rcvd file creation done from taskid: %d, file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts got a file creation done from task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TRAP_NOTASK

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x)(cuts) sent TRAP cwBulkNoTaskAvailable(60904) for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts sent trap to CWM 60904"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TRAP_START

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) sent TRAP cwBulkFileCreationStarted(60901) for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts sent trap to CWM 60901"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TRAP_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) sent TRAP cwBulkFileCreationFailed(60905) for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts sent trap to CWM 60905 which signals file creation failed."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TRAP_DONE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) sent TRAP cwBulkFileCreationDone(60902) for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts sent trap to CWM 60902"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_TRAP_ABRT

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) sent TRAP cwBulkFileCreationAborted(60903) for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cuts sent trap to CWM 60903"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_UPDT_DONE

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)API to update %s for filetype %d done"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Update to FCB and mibs for filetype specified done"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEND_CUTV_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)Failed to send %s message for filetype %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "API to send message to the CUTV task failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: UPD_FCB_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) Failed to update FCB"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "API to update the FCB returned ERROR"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TMR_REINIT_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) Failed to reinit timer with reason %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to reinitiate timers"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMGIVE_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) could not give up sem %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "semgive for sem failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_FILE_MUTEX

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)(cuts) FileIndex %d cannot be be createdsince another CONN/STATIC-CONN file is being created "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Config upload should not create both conn and conn-update files together. If there is another conn/conn-update file running, the request will be rejected"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TXID_GET_FAILED

SEVERITY: Warning
FORMAT: "(L %d:errno 0x%x) Config upload failed to receive a valid TxId from the card"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Config upload failed to receive a valid TxId from the card"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INV_TXID

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) fileType = %d, card TxID= %d less than req TxID = %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The requested TxID is greater than the card TxID"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CANNOT_PROCEED

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) fileType = %d, reqType= %d,reqTxID= %d: cutwCanCreationProceed returned FALSE"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Either due to mutual exclusion or the reqTxID being greater than the card TxID, cfgupload cannot continue"
RECMMENDED_ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TRAP_SEND_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) Trap not sent by %s for file:%d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "API to send trap failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTS_UPDT_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x)API to update %s returned error for filetype %d "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Update to FCB and mibs for filetype specified failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RMTCLOSE_FAIL

SEVERITY: Information
FORMAT: "(L %d:errno 0x%x) ssiRmtFileClose fails"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "ssiremoteclose API returned error"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "signaling"

MESSAGE: CC_AUD_REL

SEVERITY: Warning
FORMAT: "CC Func:%s; logItf:%ld;callRef:%ld,endptRef:%d\n"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Audit to release the call"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Please collect the output of CLIs:
a) General: dspver, depcds, dsplog, dsperr, dspmempart
b) Interface: dsppnports, dsppnport, dsppnportrsrc, dsppnportcac, dsppnportsig,
c) Connection: dsppncons, dspcons, dspsigstats, dsppnctlvc,
d) Congestion: dsppnportcc, dspsvcparm,
e) Topology: dsppnni-reachable-addr, dsppnni-routing-policy, dsppnni-path, dsppnni-link.

DDTS: "clocking"

MESSAGE: CLK_IPC_FAIL

SEVERITY: Major Alert
FORMAT: "CLK IPC CHANNEL FAILURE: Detected by module = %s, errno = 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "IPC Channel Failed, Clock Functionality may be affected"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd, dspver, dsperr, dspclkalms before calling the Cisco Techincal support representative.

MESSAGE: EPID_RESOLVE_FAILED

SEVERITY: Major Alert
FORMAT: "%s CLK TASK EPID INVALID"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "ACTIVE CLK TASK CAN NOT RESOLVE STBY EPID, CLOCK UPDATES NOT SEND"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd, dspver, dsperr, dspclkalms before calling the Cisco Techincal support representative.

MESSAGE: TIMER_SCHEDULE_FAIL

SEVERITY: Warning
FORMAT: "Attempt to schedule %s timer failed. Reason: %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Clock Manager Timer could not be scheduled."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd, dspver, dsperr, dspclkalms before calling the Cisco Techincal support representative.

MESSAGE: TIMER_CANCEL_FAIL

SEVERITY: Warning
FORMAT: "Attempt to cancel %s timer failed. Reason: %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Clock Manager Timer could not be cancelled."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd, dspver, dsperr, dspclkalms before calling the Cisco Techincal support representative.

DDTS: "rpm"

MESSAGE: DB_ALLOC_ERR

SEVERITY: Major Alert
FORMAT: "%s %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "This is an error logged when not able to allocate RVT database for RPM-PR card in the shelf. This will impact the provisioning on the RPM-PR for which the error is logged."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Capture the following and contact your technical support representative.
a) dspcds
b) dspcd
c) dsperr
d) dsplog
e) dspred
f) dir "E:RPM"

DDTS: "shm"

MESSAGE: BC_HLTH_UPDATE

SEVERITY: Information
FORMAT: "AppId 0x%x, tId 0x%x, tName %s , psl %d, bay %d, callerPc 0x%x, bcF %d, Bmap 0x%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "Info on caller to a SHM backcard health update API"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "config-upload"

MESSAGE: CUTW_EPID

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x)Creation of CUTW EPID \"%s\" failed rc = 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to create epid(end point communication) for cutw."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_TIMER_CREATE

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x) Creation of timer failed rc= 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Timer Creation failed"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_ATTHDLR

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x)Attaching of handler \"%s\" failed Epid = 0x%08X rc= 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Attaching of handler to a cutw epid has failed. The epid name, number and error code are listed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_TMR_SCHD

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) failed to schedule timer in \"%s\" timeout value = %d, timer type = %d, rc= 0x0%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to schedule timeout"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_TMR_CNCL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)failed to cancel timer in \"%s\" timer type = %d, rc= 0x0%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to canecl timer"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_IPC_FREE_ERR

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x) IPC Message Free Failed : rc = 0x%08X."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Error in Freeing IPC message"
RECOMMENDED ACTION: If this event shows up excessively (about 5 or more times) in the event log, please log a bug and contact TAC immediately. This is a potential memory leak.
REQUIRED_INFO: If CLI available, capture the following command output before contacting TAC:
1) dspversion
2) dspdate
3) dspmempart 2 1
4) dsplog -mod CUTS
5) dsplog -mod CUTWRKR

MESSAGE: IPCFAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) IPC SEND FAILED TO \"%s\" from \"%s\" request:%d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "IPC send failed"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, capture the following command output before contacting TAC:
1) dspversion
2) dspdate
3) dspmempart 2 1
4) dsplog -mod CUTS
5) dsplog -mod CUTWRKR

MESSAGE: IPC_ALLC_FAILED

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x) failed to allocate ipc buffer in \"%s\"."
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "failed to allocate ipc buffer. This will cause CUTS not able to communicate with this task "
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, capture the following command output before contacting TAC:
1) dspversion
2) dspdate
3) dspmempart 2 1
4) dsplog -mod CUTS
5) dsplog -mod CUTWRKR

MESSAGE: CUTW_INVALID_RQ

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) Invalid request received by cutw from system epid: req = %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Invalid request received"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTW_EPID_RESOLVE

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x) CUTW %s could NOT resolve CUTS epid"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Not able to resolve the scheduler task's epid"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_WRKR_UPDAT

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) failed to update the worker task of index (%d) to state %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTW unable to update worker task state"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTW_INIT_PTR

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x) CUTW Task init failed due to a NULL taskControlBlockPtr in %s, tid = 0x%0X"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "CUTW init failed due to a null task controlblock ptr"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: If CLI available, please capture the following command output before contact TAC:
1) dspversion
2) dspdate
3) dsplog -mod CUTS
4) dsplog -mod CUTWRKR
5) dsplog

MESSAGE: CUTW_FC_FAILED

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) cutw failed to process file creation request for file 0x%08X."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to validate file creation request"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BAD_FILEINDX

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) Invalid File index found in \"%s\" file Index = %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw found an invalid file index "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CUTWFILENAME

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)filename created for the request is \"%s\" file Index = %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw created the name for the file creation request "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: W_RATEVENTPENDING

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x) RAT event %d pending found while creating file Index = %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw had to abort while creating a file due to rat events "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: NULL_FILEP

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw) NULL FILEPTR PASSED IN to %s routine"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw found an invalid file ptr "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TASK_STATUS_TRANS

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw) Task status transition from \"%s\" to \"%s\"."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Task is transitioning from one state to another"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMTAKE_FAIL

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw) Can't take semaphore for \"%s\" in function \"%s\"."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw was not abe to take a semaphore"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEMGIVE_FAIL

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw) Can't release semaphore for \"%s\" in function \"%s\"."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw was not abe to release a semaphore"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: NULL_PTR

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw) NULL pointer PASSED IN to \"%s\" routine"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw found a null ptr "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MEM_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to allocate mem for %s for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to allocate buffer. This Config Upload file creation request will not be successful. "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MEMDEALL_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to deallocate mem for %s for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to deallocate buffer. This could lead to memory leak "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RTOID_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to write ROOT OID for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write root oid which cause this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TBLOID_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to write ROOT OID for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write table oid which cause this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CNFOID_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to write item OID %d,col %d, for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write item oid which cause this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CNFVRBND_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to write CNFVRBND table %d,col %d, for file index %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write cnfg varbind which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: FINDOBJ_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)find_object failed for oidTbl->oidListInx=%u for file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw cannot find the current OID which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: GTNXT_FAIL

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw)Empty Table found, continuing.. for file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw found an empty table "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: WRITE_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)failed to write %s for file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write data to file which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: GET_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)File %d Serial# %d oid %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to do a get operation which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: GETNEXT_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) Serial# %d type %d oid %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to do a get-next operation which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: GETSCLR_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw) Get failed for object table %d,col %d for file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw write failed "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: IOCTL_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw)call to %s failed while creating file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw ioctl call failed "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CR_RESULT

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutw)FILE CREATION RESULTED IN %s for file %d : File size: %ld : Checksum: %x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw file creation result "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: FILE_ERR

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw) %s for file %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw file creation result "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: WRITE_BYTESFAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutw) Write Fail for File %d: requested bytes %d bytes written %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw failed to write requested number of data to file which causes this Config Upload file creation aborted "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MAX_ROWS_EXCEEDED

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x)(cutw) Write Fail for File %d: Too many rows: limit is %d, currently %d. oidTblInx=%d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutw aborted the file creation because number of rows allowed for this file exceeded the defined limit"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INVALID_PARAM

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Invalid parameter passed: 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Invalid parameter was received by the function"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TXID_GET_FAILED

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Config upload failed to receive a valid TxId from the card"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Config upload failed to receive a valid TxId from the card"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TIME_GET_FAILED

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to get current time of day"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to get current time of day"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: OPEN_FAILED

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to open file %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to open a file"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: FNAME_PARSE_ERROR

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to parse filename %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to parse a filename"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BITMAP_FAILURE

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to get connection bitmap"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to get the connection bitmap"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: NULL_ERRHDLR

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)No error handler found, fileType=%d, i=%d, j=%d, k=%d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to read enoughd data from alarm file"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: FILE_READFAIL

EVERITY Warning
FORMAT: "(Line %d:errno 0x%x): (cutv) cannot open file (fd:%d, name:%s) with read permission in function %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutv failed open file with read permission"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: REMOVE_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutv) remove failed for %s in
function %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "cutv cannot remove the file. remove failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: VLDN_THRESH_EXCEED

SEVERITY: Information
FORMAT: "(Line %d:errno 0x%x)(cutv) failed to open file with read permission too many times in %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "validation counter exceeded threshold"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RMT_FILE_IOCTL_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)(cutv) remote file ioctl fail in %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "remote file ioctl failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: LATEST_STATIC_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to find the latest static conn file"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to find the latest static conn file"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INVALID_REQ

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Invalid request given to the engine: %d, filetype =%d\n"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Invalid request given to the engine"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: REQ_PROC_INVALID

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Invalid request processing entry in the request matrix, reqtype=%d, filetype =%d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Invalid request processing entry in the request matrix"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INVALID_PROC_PARTS

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Invalid processing parts reqtype=%d, filetype =%d, totalProcessingParts=%d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Invalid request processing entry in the request matrix"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INVALID_SLOT

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Invalid slot "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to get slot# from CTC"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEEK_UPDATE_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to seek into file for updating length"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to seek into file for updating length"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: REPLICATE_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to replicate the file %s to standby PXM"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Asynchronous file replication API failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: INVALID_REQ_TXID

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Config upload received a requested TxId larger than the card TxId"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Config upload received a request to create incremental file with TxId larger than the one on the card"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: TXID_AUDIT_FAILED

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Config upload requested audit of card TxId and the audit failed"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Config upload received a request to create incremental file with TxId larger than the one on the card. It requested audit of card TxId and it could not be fixed."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: CHKSUM_FAILURE

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Checksum failed for file %s: compChecksum=0x%x, readChecksum=0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "One byte checksum in the file did not match with the calculated checksm"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MEM_ALLOC_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to allocate %d bytes in memory"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Memory allocation failure"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: ALARM_BUFF_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to get latest alarm file data "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to get latest alarm file data from cPro/conPro applications"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: STBY_REMOVE_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to remove %s from stdby"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to get latest alarm file data from cPro/conPro applications"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO No required info

MESSAGE: STATIC_DEL_FAIL

SEVERITY: Error
FORMAT: "(Line %d:errno 0x%x)Static file deletion resulted in %s for slot %d on controller card %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to remove static connection files from a controller card. There might be disk issues (refer errno)"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DIR_CHECK_FAIL

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Failed to check directory %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "There was an error encountered while checking for the directory specified. This could be because the dir name was invalid or because the init dirs failed."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: ADDINT_FAILURE

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x)Overflow in the working pointer on call to AddInt. wrkPtr = 0x%x, tmpPtr = 0x%x, TxId = %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "There was an error on call to AddInt api that encodes the TxId in ASN.1 format. It overwrote extra amount of memory"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO No required info

MESSAGE: SANITY_FAILURE

SEVERITY: Warning
FORMAT: "(Line %d:errno 0x%x) Sanity check failed: %s :0x%x, 0x%x "
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "There was an error on call to AddInt api that encodes the TxId in ASN.1 format. It overwrote extra amount of memory"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "diskdb"

MESSAGE: DBCLNT_INFO

SEVERITY: Information
FORMAT: "%s %s <0x%x> %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The INFO string should be self-explained."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "shm"

MESSAGE: NFATAL_MAJ_ERPT3

SEVERITY: Information
FORMAT: "%s: AppId 0x%x, tId 0x%x, tName %s , Ref. pslot %d, callerPc 0x%x, evtNum 0x%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "Info on caller to a SHM fatal error resource report API"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: FRUMISMATCH_RPT

SEVERITY: Information
FORMAT: "AppId 0x%x,tId 0x%x,tName %s,pslot %d,bay# %d callPc 0x%x,BcCnfState %d,Mismatch[Aps 0x%x,NonAps 0x%x)"
FLAG: Stack Trace|Write Bram
LIMIT: No Throttling
EXPLANATION: "Info on caller to a BackCard FRU Mismatch State Change report API"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BC_HLTH_UPDATE

SEVERITY: Information
FORMAT: "AppId 0x%x, tId 0x%x, tName %s , psl %d, bay %d, callerPc 0x%x, bcF %d, Bmap 0x%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "Info on caller to a SHM backcard health update API"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: IP_NOT_CONFIGURED

SEVERITY: Information
FORMAT: "%s: AppId 0x%x, tId 0x%x, tName %s, callerPc 0x%x, %s"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "SHM query for IP address returned error IP not configured "
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: GEN_ERROR

SEVERITY: Information
FORMAT: "Line %d: %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Reports a SHM general error, the event contains more details"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Techincal support representative.

MESSAGE: EPID_CREATE_ERR

SEVERITY: Error
FORMAT: "SHM ERR: Epid Create Failed in %s, Errno = 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "ssiIpcComEpCreate failed, check the Errno."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: SFM_SEND_ERR

SEVERITY: Error
FORMAT: "Sfm Send failed, AppId 0x%x, tId 0x%x, tName %s , Ref. pslot %d, callerPc 0x%x, Evt Num: 0x%x, Msg Type: 0x%x, Reason: %s"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "This provides the information when a card fails to come up due to IPC version mismatch."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: INTERCD_APS_RPT

SEVERITY: Information
FORMAT: "%s: AppId 0x%x, tId 0x%x, tName %s , Ref. pslot %d, callerPc 0x%x, evtNum 0x%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "Info on caller to a SH inter-card aps resource report API"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS:"ssi"

MESSAGE: HANGTASK_MSEC

SEVERITY: Minor Alert
FORMAT: "Task %p[%s] has been %s at %p for %d milliseconds."
LIMIT: One Tick
EXPLANATION: "The system has a critical task that is hung on the specified object for the specified time. This event is same as HANGTASK except display in milliseconds format"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: ATADRVERR

SEVERITY: Error
FORMAT: "ATA driver error. %s (%s), retry: %d.cyl: 0x%x, head: %d, sec: %d, nSec: %d"
LIMIT: One Minute
EXPLANATION: "The ATA driver detected a HDD status error. This error event contains the device registers of hardware devices between the CPU and the HDD. Please contact the TAC engineers to analysis the captured data and recommend a recover action, if required. Use dsperr (not dsperrs) to display all data capture in this error event log."
RECOMMENDED ACTION: "Capture the output of dsperr command on the PXM slot in which the problem occurred."
REQUIRED_INFO: No required info

MESSAGE: ATAWAITERR

SEVERITY: Error
FORMAT: "ATA driver error (%s). mask: 0x%x, req: 0x%x"
LIMIT: One Minute
EXPLANATION: "The ATA driver detected a HDD status error. This error event contains the device registers of hardware devices between the CPU and the HDD. Please contact the TAC engineers to analysis the captured data and recommend a recover action, if required. Use dsperr (not dsperrs) to display all data capture in this error event log."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: ATADRVINFO

SEVERITY: Information
FORMAT: "ATA driver info. %s (%s), retry: %d.cyl: 0x%x, head: % d, sec: %d, nSec: %d"
LIMIT: One Minute
EXPLANATION: "The ATA driver detected a HDD IO operation failure This error event contains the device registers of hardware devices between the CPU and the HDD. This event is for information only."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: HNGNOSTKTRC

SEVERITY: Minor Alert
FORMAT: "Task %p[%s] has been %s at %p for %d minutes."
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "The system has a task that is hung on the specified object for the specified time. This event is same as HANGTASK except that trace is not dumped because the semaphore that is necessary to dump the trace is not available."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

DDTS: "shm"

MESSAGE: FUNC_FAILED

SEVERITY: Information
FORMAT: "%s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "tRed function call failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO No required info

MESSAGE: SRM_UNAVAIL

SEVERITY: Warning
FORMAT: "%s : Bay %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "SRM for the particular bay is not available"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MAKE_HSB_ACTIVE_FAILED

SEVERITY: Warning
FORMAT: "%s, Slot %d, Redundant slot %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Error in making HSB go Active"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: SEC_CD_INFO

SEVERITY: Information
FORMAT: "%s, red type=%d,state= %d, slot %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Setting the Secondary card state"
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: AC_TIME_OUT_ERR

SEVERITY: Information
FORMAT: "State Time out %s, slot %d"
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "Auto Card time out error."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: AC_DWNLBRAMERR

SEVERITY: Information
FORMAT: "ACRED: Download BRAM Failed %s. From %d to %d"
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "BRAM download error."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: AC_UPLDBRAMERR

SEVERITY: Information
FORMAT: "Upload BRAM Failed %s , Pslot %d, Lslot %d"
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "BRAM upload error."
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: DUPLICATE_CONNID_EXISTS

SEVERITY: Error
FORMAT: "rec: %d; conn (%d.%d.%d) already exists in rec# %d;"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "duplicate conn. entry found in a different record"
RECOMMENDED ACTION: "This event is logged when the same connection id exists on two different connection records"
REQUIRED_INFO: "From both active and standby PXM cards,
1) zip the event/error logs
2) save the config (saveallconfig)
3) ftp over the config and log zip files."

DDTS: "diskdb"

MESSAGE: RESV_NO_DB

SEVERITY: Error
FORMAT: "Slot %d: %s"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: " The slot is pseudo-resv and reserved from th SHM perspective but its DB2 directory does no have any DBs for the specified slot"
RECOMMENDED ACTION: "Call TAC"
REQUIRED_INFO: "Save event logs, error logs and ll from D:/DB2"

MESSAGE: NO_PSEU_NO_RESV

SEVERITY: Major Alert
FORMAT: "Slot %d: %s"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: " The slot is not pseduo reserved, not reserved form SHM perspective but its DB is existed i DB2 directory"
RECOMMENDED ACTION: "Call TAC"
REQUIRED_INFO: "Save event logs, error logs and ll from D:/DB2"

MESSAGE:DETECT_UNDESIRE

SEVERITY: Warning
FORMAT: "Slot %d info: %s"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "The slot is detected with the specified undesire info."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: PSEUDO_ONLY

SEVERITY: Information
FORMAT: "Slot %d info: %s"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The slot is detected with pseudo reserved only"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: DBSVR_TRAPWARNING

SEVERITY: Warning
FORMAT: "%s:%s- %s "
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "DB Server fails to generate Trap."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "diskdb"

MESSAGE: DBSYNC_INFO

SEVERITY: Information
FORMAT: "%s:%s %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "DB Sync detected some info condition"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

DDTS: "ssi"

MESSAGE: MBLKBUFFREEFAIL

SEVERITY: Error
FORMAT: "Failed to free data buffer %x, errno %x, callerPc 0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to free data buffer"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: MBLKFREEFAIL

SEVERITY: Error
FORMAT: "Failed to free mblk %x, errno %x, callerPC:0x%x"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "Failed to free mblk"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

DDTS: "snmp-ma"

MESSAGE: EPIDWARN

SEVERITY: Warning
FORMAT: "Parm %s value '0x%x' is invalid to %s."
FLAG: No Flag
LIMIT: Ten Seconds
EXPLANATION: "API Software Error. The parameter value for the named parameter passed in as an argument to the named function was invalid."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: "On PXM:
1. dspcds
2. dsplog
3. dsperr
4. dsprev"

MESSAGE: EPIDERROR

SEVERITY: Error
FORMAT: "Parm %s value '0x%x' is invalid to %s."
FLAG: Stack Trace | Write Bram
LIMIT: One Hour
EXPLANATION: "API Software Error. The parameter value for the named parameter passed in as an argument to the named function was invalid."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: "On PXM:
1. dspcds
2. dsplog
3. dsperr
4. dsprev"

DDTS: "ctc"

MESSAGE: RATERR030

SEVERITY: Warning
FORMAT: "Ack for RAT \"%s\", task \"%s\" (%d) with unexpected status \"%s\" (0x%08X). pRat 0x%x pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The task receive ACK from it child but it child's status is not in processing mode. This will result in child's status to set to fail."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR031

SEVERITY: Warning
FORMAT: "RAT \"%s\" task offset (%d) exceeds range (%d). pRat 0x%x, pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Timeout event receive from a child outside the range of the table"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR054

SEVERITY: Warning
FORMAT: "Invalid Child Id. pRat 0x%x, pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The task received message from unknown source"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR056

SEVERITY: Warning
FORMAT: "Received unexpected message from child (offset = %d). pRat 0x%x pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "We shouldn't receive a message from a task where there aren't any outstanding requests"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR057

SEVERITY: Warning
FORMAT: "Invalid state!!! offset = %d, state = (\"%s\"). pRat 0x%x pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The state of the child entry is invalid. Task failed."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR058

SEVERITY: Warning
FORMAT: "Unexpected response received from child task. offset = %d, expected resp = \"%s\". pRat 0x%x pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Unexpected response received from child task. The response should be OK"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR059

SEVERITY: Warning
FORMAT: "ssiTimeoutCancel(), Can not cancel timeout timer for offset %d, result %d, pRat 0x%x pMblk 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Can not cancel timeout timer for child task"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR060

SEVERITY: Error
FORMAT: "ssiIpcMessageFree(), Can not free message for offset %d, result %d, pRat 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Can not free memory. This can result in potential memory leak"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. Do the same with 'dsplog' command. If you cannot determine the nature of the error from the error message text or from the 'dsperr'/'dsplog' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: RATERR061

SEVERITY: Warning
FORMAT: "ssiTimeoutCancel(), Can not cancel overall timer, result %d, pRat 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Cancellation of timer failed"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR062

SEVERITY: Warning
FORMAT: "Role change attempt to \"%s\" results in \"%s\". pRat 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Failed to transition to new state."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: RATERR063

SEVERITY: Error
FORMAT: "at end of rat_comEpWait_msgHdlr() state (\"%s\") is invalid. pRat 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The task is not successfully transition to new state"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. Do the same with 'dsplog' command. If you cannot determine the nature of the error from the error message text or from the 'dsperr'/'dsplog' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: RATERR084

SEVERITY: Error
FORMAT: "Corrupted msg from RAT %s, task \"%s\" (%d), cookie = 0x%08X, pRat 0x%x pMblk 0x%x."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "A message was received whose magic cookie was invalid."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. Do the same with 'dsplog' command. If you cannot determine the nature of the error from the error message text or from the 'dsperr'/'dsplog' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

DDTS: "axsm_apps"

MESSAGE: APS_ERROR

SEVERITY: Notice
FORMAT: "APS Error: line %d, %s : 0x%x"
FLAG: Stack Trace
LIMIT: No Throttling
EXPLANATION: "APS Task Error "
RECOMMENDED ACTION: "Copy the error message exactly as it appears in the system log. Call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Capture the output of these CLIs
On PXM45:
a) dsplog -sl <slot that experienced the error>
b) dsperr -sl <slot that experienced the error>

DDTS: "ssi"

MESSAGE: BELOWTHRES

SEVERITY: Warning
FORMAT: "Cannot allocate %d bytes. Not enough %s prio mem exists in mempart %d. Thresh %d bytes, Free %d bytes."
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "Allocation failed because number of free bytes is below threshold. Currently there is a limit on the bytes available for low and high priority allocation requests. These limits are visible using the dspmempart command for a given partition. This can be the result of a memory leak in the partition."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: NOPARTITION

SEVERITY: Warning
FORMAT: "Could not allocate %d bytes from partition 0x%x for %s priority data (errno 0x%x)."
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "An error was returned by ssiMalloc while attempting to allocate low or high priority memory. If critical memory allocation, then memPartAlloc failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: DOWNSTATIC

SEVERITY: Warning
FORMAT: "Not enough memory in the dynamic pool for %d bytes, trying static"
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "The dynamic partition does not have enough space to allocate the specified number of bytes. The software will try to allocate the space from the static partition."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: DOWNVXWORKS

SEVERITY: Warning
FORMAT: "Not enough memory in the static pool for %d bytes, trying VxWorks' heap"
FLAG: Stack Trace
LIMIT: One Second
EXPLANATION: "The static partition does not have enough space to allocate the specified number of bytes. The software will try to allocate the space from the VxWorks heap."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: ERRBUFFCORR

SEVERITY: Error
FORMAT: "Error buffer corruption detected and re-init. %s. List 0x%x, node 0x%x, next 0x%x, count %d"
FLAG: Write Bram
LIMIT: One Tick
EXPLANATION: "SSI detected Error and Trace buffers corruption. The trace and error buffers are re-initialized during card boot-up. Some trace and/or error events may be lost."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: "Event, error logs, core dump, and the output of shell command 'logConsoleShow'. Events logs must include all the entries that had occurred 15 minutes before the time of this event."

MESSAGE: HANGTHRESH

SEVERITY: Error
FORMAT: "hangThresh %d or starvationThresh %d is invalid, caller PC 0X%x."
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "task starvation or hang threshold value is out of range. threshold is used by task monitor to determine the task starvation or hang situation"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the 'dsperr' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

DDTS: "shm"

MESSAGE: SCM_PARMS_CHG

SEVERITY: Information
FORMAT: "Change SCM Poll Parms: MaxPollRetry, MaxMissPoll, MonFromStby: From %d, %d, %d To: %d, %d, %d."
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "User is changing the SCM poll parms"
RECOMMENDED ACTION: No action required
REQUIRED_INFO: No required info

MESSAGE: MCAST_VER_CHG1

SEVERITY: Warning
FORMAT: "mcastSenderVersion invalid, changing it from %d to %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The global variable that has the multicast version is accidently changed to invalid. This event indicates that it has been changed back to its value."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. Do the same with 'dsplog' command. If you cannot determine the nature of the error from the error message text or from the 'dsperr'/'dsplog' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: MCAST_VER_CHG2

SEVERITY: Warning
FORMAT: "global var (%d), node db (%d) copies of mcastSenderVersion are invalid, changing to %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The global variables that have the multicast version are accidently changed to invalid. This event indicates that they have been changed back to normal expected value."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log. Issue the 'dsperr' command from the PXM to gather data that may provide information to determine the nature of the error. Do the same with 'dsplog' command. If you cannot determine the nature of the error from the error message text or from the 'dsperr'/'dsplog' output, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: No required info

MESSAGE: MASTERSHIP_REL

SEVERITY: Information
FORMAT: "Slot %d is releasing its mastership by deasserting FWREADY bit"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The Mastership is being released to the other PXM."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BC_INFO_FIXED

SEVERITY: Information
FORMAT: "pslot %d, bay %d, hasBcF %d, hasBmap %d, bcFailed %d, bmap 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This event will be logged when bcFailed is TRUE but bmap is either missing or contains no failure bit in the BC insert message. The bmap will be changed internally to indicate unknown BC failure."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BC_BMAP_INV

SEVERITY: Information
FORMAT: "pslot %d, bay %d, bcFailed %d, bmap 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This event will be logged when unknown bits are detected in the BC health bitmap in the BC insert event message."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BC_INFO_IGNORED

SEVERITY: Information
FORMAT: "pslot %d, bay %d, hasBcF %d, hasBmap %d, bcFailed %d, bmap 0x%x"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "This event will be logged when either (1) EXTPOLL_BC_FAILED_OID is missing or (2) BC health info inconsistency is detected the BC insert event message."
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: BC_HLTH_CHNGED

SEVERITY: Information
FORMAT: "%s: pslot %d, bay %d, oldBcF %d, newBcF %d, oldBmap 0x%x, newBmap 0x%x"
FLAG: Write Bram
LIMIT: No Throttling
EXPLANATION: "BC Health Info update"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MC_VER_CHG

SEVERITY: Warning
FORMAT: "Multicast receiver in pslot %d can only support upto version %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "The multicast receiver at the indicated slot cannot understand the sender's version. Sender will adjust to lower version"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: API_CALL_ERR

SEVERITY: Error
FORMAT: "API %s, called by SHM returned Error (0x%x)"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "SHM_ERR: An API called by SHM failed."
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.

MESSAGE: XBAR_NOT_UP

SEVERITY: Information
FORMAT: "%s reported against xbar slot: %d, xbarPlane: %d, errPSlot: %d, errType: %d, errSeverity:%d, %s"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "There was an error reported on xbar slot which is either not present or the xbar is not enabled yet, not shuting down the link"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: HV_PORT_INVALID

SEVERITY: Information
FORMAT: "Humvee Error reported against invalid/unused port: %d for Slot: %d, errType: %d, errSeverity: %d"
FLAG: No Flag
LIMIT: One Tick
EXPLANATION: "There was an error reported on a invalid humvee port, so not processing the error"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: MASTERSHIP_OK

SEVERITY: Information
FORMAT: "Mastership bits ok IM IR HM HR HCR: From: %s %s %s %s %s To: %s %s %s %s %s, Log Count: %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "The Mastership bits went to ok state from an invalid state"
RECOMMENDED ACTION: No Recommended Action
REQUIRED_INFO: No required info

MESSAGE: HW_LOG_TRAP_ERR

SEVERITY: Error
FORMAT: "Trap Send Failed: %s, Error Code: %d"
FLAG: No Flag
LIMIT: No Throttling
EXPLANATION: "Trap send failed"
RECOMMENDED ACTION: Copy the error message exactly as it appears in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
REQUIRED_INFO: Enter the CLI commands dspcds, dspcd (for PXM and for the slot the error is found), dspver, dsperr, ls C:/FW before calling the Cisco Technical support representative.