Cisco Catalyst 3750 Metro Switch System Message Guide, Rel. 12.2(55)SE
System Message Overview
Downloads: This chapterpdf (PDF - 167.0KB) The complete bookPDF (PDF - 2.46MB) | Feedback

System Message Overview

Table Of Contents

System Message Overview

How to Read System Messages

Error Message Traceback Reports

Output Interpreter

Bug Toolkit

Contacting TAC


System Message Overview


This guide describes the Catalyst 3750 Metro-specific system messages. During operation, the system software sends these messages to the console (and, optionally, to a logging server on another system). Not all system messages mean problems with your system. Some messages are informational, and others can help diagnose problems with communications lines, internal hardware, or the system software.


Note For information about system messages that are not Catalyst 3750 Metro-specific, see the Cisco IOS System Error Messages, Cisco IOS Release 12.2.


How to Read System Messages

Error Message Traceback Reports

How to Read System Messages

System log messages can contain up to 80 characters and a percent sign (%), which follows the optional sequence number or time-stamp information, if configured. Messages appear in this format:

seq no:timestamp: %facility-severity-MNEMONIC:description (hostname-n)

By default, a switch sends the output from system messages to a logging process.

Each system message begins with a percent sign (%) and is structured as follows:

%FACILITY-SEVERITY-MNEMONIC: Message-text

FACILITY is a two or more uppercase letters that show the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software. Table 1-1 lists Catalyst 3750-specific facility codes.

These messages are described in Chapter 2, "Message and Recovery Procedures," in alphabetical order by facility code with the most severe (lowest number) errors described first.

Table 1-1 Facility Codes 

Facility Code
Description
Location

ACLMGRR

ACL manager

"ACLMGR Messages" section on page 2-3

AUTHMGR

Authorization Manager

"AUTHMGR Messages" section on page 2-6

BACKUP_INTERFACE

Backup Interface

"BACKUP_INTERFACE Messages" section on page 2-8

BADTRANSCEIVER

Bad Transceiver

"BADTRANSCEIVER Messages" section on page 2-8

BSPATCH

Boot loader patch

"BSPATCH Messages" section on page 2-8

CMP

Cluster Membership Protocol

"CMP Messages" section on page 2-9

DHCP_SNOOPING

DHCP snooping

"DHCP_SNOOPING Messages" section on page 2-10

DOT1Q_TUNNELLING

802.1Q tunneling

"DOT1Q Tunneling Messages" section on page 2-14

DOT1X

802.1x

"DOT1X Messages" section on page 2-14

DOT1X_SWITCH

802.1x for switches

"DOT1X_SWITCH Messages" section on page 2-20

DTP

Dynamic Trunking Protocol

"DTP Messages" section on page 2-23

EC

EtherChannel

"EC Messages" section on page 2-24

EPM

EPM

"EPM Messages" section on page 2-29

ESF

Enhanced services forwarding (ESF)

"ESF Messages" section on page 2-30

ETHCNTR

Ethernet Controller

"ETHCNTR Messages" section on page 2-30

EXPRESS_SETUP

Express Setup

"EXPRESS_SETUP Messages" section on page 2-31

FRNTEND_CTRLR

Front-end controller

"FRNTEND_CTRLR Messages" section on page 2-32

GBIC_SECURITY

Gigabit Interface Converter (GBIC) module and small form-factor pluggable (SFP) module security

"GBIC_SECURITY Messages" section on page 2-32

GBIC_SECURITY_CRYPT

GBIC and SFP module security

"GBIC_SECURITY_CRYPT Messages" section on page 2-34

GBIC_SECURITY_UNIQUE

GBIC and SFP module security

"GBIC_SECURITY_UNIQUE Messages" section on page 2-35

HARDWARE

Hardware

"HARDWARE Messages" section on page 2-35

HLFM

Local forwarding manager

"HLFM Messages" section on page 2-37

IDBMAN

Interface database manager process

"IDBMAN Messages" section on page 2-38

IF MGR

Interface manager

"IFMGR Messages" section on page 2-41

ILET

ILET

"ILET Messages" section on page 2-41

MAC_LIMIT

MAC address table entries

"Recommended Action   Contact your Cisco sales representative for assistance" section on page 2-42

MAC_MOVE

Host activity

"MAC_MOVE Messages" section on page 2-43

PAGP_DUAL_ACTIVE

Port Aggregation Protocol (PAgP) dual-active detection

"PAGP_DUAL_ACTIVE Messages" section on page 2-43

PHY

PHY

"PHY Messages" section on page 2-43

PIMSN

Protocol Independent Multicast (PIM) snooping

"PIMSN Messages" section on page 2-45

PLATFORM

Low-level platform-specific

"PLATFORM Messages" section on page 2-46

PLATFORM_CAT3750

Catalyst 3750 internal

"PLATFORM _CAT3750 Messages" section on page 2-46

PLATFORM_FBM

Fallback bridging manager

"PLATFORM_FBM Messages" section on page 2-47

PLATFORM_PBR

Policy-based routing

"PLATFORM_PBR Messages" section on page 2-48

PLATFORM_PM

Port manager

"PLATFORM_PM Messages" section on page 2-50

PLATFORM_SPAN

Switched Port Analyzer (SPAN)

"PLATFORM_SPAN Messages" section on page 2-51

PLATFORM_UCAST

Platform unicast routing

"PLATFORM_UCAST Messages" section on page 2-51

PLATFORM_VLAN

VLAN

"PLATFORM_VLAN Messages" section on page 2-53

PM

Port manager

"PM Messages" section on page 2-54

PORT SECURITY

Port security

"PORT SECURITY Messages" section on page 2-62

QOSMGR

QoS manager

"QOSMGR Messages" section on page 2-63

REP

Resilient Ethernet Protocol

"REP Messages" section on page 2-68

RMON

Remote network monitoring

"RMON Messages" section on page 2-69

SCHED

SCHED

"SCHED Messages" section on page 2-70

SPAN

Switched Port Analyzer (SPAN)

"SPAN Messages" section on page 2-70

SPANTREE

Spanning tree

"SPANTREE Messages" section on page 2-71

SPANTREE_FAST

Spanning-tree fast convergence

"SPANTREE_FAST Messages" section on page 2-78

SPANTREE_VLAN_SW

Spanning-tree VLAN switch

"SPANTREE_VLAN_SW Messages" section on page 2-78

STORM_CONTROL

Storm control

"STORM_CONTROL Messages" section on page 2-79

SUPERVISOR

Supervisor ASIC

"SUPERVISOR Messages" section on page 2-80

SUPQ

Supervisor queue

"SUPQ Messages" section on page 2-80

SW_DAI

Dynamic ARP inspection

"SW_DAI Messages" section on page 2-82

SW_VLAN

VLAN manager

"SW_VLAN Messages" section on page 2-84

SWITCH_QOS_TB

QoS trusted boundary

"SWITCH_QOS_TB Messages" section on page 2-90

TCAMMGR

Ternary content addressable memory manager

"TCAMMGR Messages" section on page 2-91

UDLD

UniDirectional Link Detection (UDLD)

"UDLD Messages" section on page 2-92

VQPCLIENT

VLAN Query Protocol (VQP) client

"VQPCLIENT Messages" section on page 2-93


SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table 1-2 lists the message severity levels.

Table 1-2 Message Severity Levels 

Severity Level
Description

0 - emergency

System is unusable.

1 - alert

Immediate action required.

2 - critical

Critical condition.

3 - error

Error condition.

4 - warning

Warning condition.

5 - notification

Normal but significant condition.

6 - informational

Informational message only.

7 - debugging

Message that appears during debugging only.


MNEMONIC is a code that uniquely identifies the message.

Message-text is a text string describing the condition. This portion of the message sometimes contains detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 1-3 lists the variable fields in messages.

Table 1-3 Variable Fields 

Representation
Type of Information

[dec]

Decimal integer

[char]

Single character

[chars]

Character string

[enet]

Ethernet address (for example, 0000.FEED.00C0)

[hex]

Hexadecimal integer

[inet]

Internet address


This example shows a partial switch system message:

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up
00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up
00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed 
state to down 2 
*Mar  1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)
18:47:02: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)
*Mar  1 18:48:50.483 UTC: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36) 

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up (Switch-2)
00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/1, changed state to up (Switch-2)
00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/2, changed state to up (Switch-2)
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 
(Switch-2)
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/1, changed 
state to down 2 (Switch-2)

Error Message Traceback Reports

Some messages describe internal errors and contain traceback information. Include this information when you report a problem to your technical support representative.

This message example includes traceback information:

-Process= "Exec", level= 0, pid= 17
-Traceback= 1A82 1AB4 6378 A072 1054 1860 

Some system messages ask you to copy the error messages and take further action. These online tools also provide more information about system error messages.

Output Interpreter

The Output Interpreter provides additional information and suggested resolutions based on the output of many CLI commands, such as the show tech-support privileged EXEC command.

https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl

Bug Toolkit

The Bug Toolkit provides information on open and closed caveats and allows you to search for all known bugs in a specific Cisco IOS Release.

http://tools.cisco.com/Support/BugToolKit/

Contacting TAC

If you cannot determine the nature of the error, see the "Obtaining Documentation and Submitting a Service Request" section on page viii for further information.