Catalyst 6500 Release 12.2SY Software Configuration Guide
IP Source Guard
Downloads: This chapterpdf (PDF - 231.0KB) The complete bookPDF (PDF - 18.17MB) | Feedback

IP Source Guard

Table Of Contents

IP Source Guard

Prerequisites for IP Source Guard

Restrictions for IP Source Guard

Information About IP Source Guard

Overview of IP Source Guard

IP Source Guard Interaction with VLAN-Based Features

Channel Ports

Layer 2 and Layer 3 Port Conversion

IP Source Guard and Voice VLAN

IP Source Guard and Web-Based Authentication

Default Settings for IP Source Guard

How to Configure IP Source Guard

Displaying IP Source Guard PACL Information

Displaying IP Source Binding Information


IP Source Guard


Prerequisites for IP Source Guard

Restrictions for IP Source Guard

Information About IP Source Guard

Default Settings for IP Source Guard

How to Configure IP Source Guard

Displaying IP Source Guard PACL Information

Displaying IP Source Binding Information


NoteFor complete syntax and usage information for the commands used in this chapter, see these publications:

http://www.cisco.com/en/US/products/ps9536/prod_command_reference_list.html

Cisco IOS Release 12.2SY supports only Ethernet interfaces. Cisco IOS Release 12.2SY does not support any WAN features or commands.



Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum


Prerequisites for IP Source Guard

None.

Restrictions for IP Source Guard

Because the IP source guard feature is supported only in hardware, IP source guard is not applied if there are insufficient hardware resources available. These hardware resources are shared by various other ACL features that are configured on the system. The following restrictions apply to IP source guard:

Supported only on ingress Layer 2 ports.

Supported only in hardware; not applied to any traffic that is processed in software.

Does not support filtering of traffic based on MAC address.

Is not supported on private VLANs.

Information About IP Source Guard

Overview of IP Source Guard

IP Source Guard Interaction with VLAN-Based Features

Channel Ports

Layer 2 and Layer 3 Port Conversion

IP Source Guard and Voice VLAN

IP Source Guard and Web-Based Authentication

Overview of IP Source Guard

IP source guard provides source IP address filtering on a Layer 2 port to prevent a malicious host from impersonating a legitimate host by assuming the legitimate host's IP address. The feature uses dynamic DHCP snooping and static IP source binding to match IP addresses to hosts on untrusted Layer 2 access ports.

Initially, all IP traffic on the protected port is blocked except for DHCP packets. After a client receives an IP address from the DHCP server, or after static IP source binding is configured by the administrator, all traffic with that IP source address is permitted from that client. Traffic from other hosts is denied. This filtering limits a host's ability to attack the network by claiming a neighbor host's IP address. IP source guard is a port-based feature that automatically creates an implicit port access control list (PACL).

IP Source Guard Interaction with VLAN-Based Features

Use the access-group mode command to specify how IP source guard interacts with VLAN-based features (such as VACL and Cisco IOS ACL and RACL).

In prefer port mode, if IP source guard is configured on an interface, IP source guard overrides other VLAN-based features. If IP source guard is not configured on the interface, other VLAN-based features are merged in the ingress direction and applied on the interface.

In merge mode, IP source guard and VLAN-based features are merged in the ingress direction and applied on the interface. This is the default access-group mode.

Channel Ports

IP source guard is supported on Layer 2 port-channel interfaces but not on the port members. When IP source guard is applied to a Layer 2 port-channel channel interface, it is applied to all the member ports in the EtherChannel.

Layer 2 and Layer 3 Port Conversion

When an IP source guard policy is configured on a Layer 2 port, if the port is reconfigured as a Layer 3 port, the IP source guard policy no longer functions but is still present in the configuration. If the port is reconfigured as a Layer 2 port, the IP source guard policy becomes effective again.

IP Source Guard and Voice VLAN

IP source guard is supported on a Layer 2 port that belongs to a voice VLAN. For IP source guard to be active on the voice VLAN, DHCP snooping must be enabled on the voice VLAN. In merge mode, the IP source guard feature is merged with VACL and Cisco IOS ACL configured on the access VLAN.

IP Source Guard and Web-Based Authentication

You can configure IP source guard and web-based authentication (see Chapter 81 "Web-Based Authentication") on the same interface. Other VLAN-based features are not supported when IP Source Guard and web-based authentication are combined.

Default Settings for IP Source Guard

None.

How to Configure IP Source Guard

To enable IP source guard, perform this task:

 
Command
Purpose

Step 1 

Router(config)# ip dhcp snooping 

Enables DHCP snooping globally.

Step 2 

Router(config)# ip dhcp snooping vlan number 
[number]

Enables DHCP snooping on your VLANs.

Step 3 

Router(config)# interface interface-name

Selects the interface to be configured.

Step 4 

Router(config-if)# no ip dhcp snooping trust

Use the no keyword to configure the interface as untrusted.

Step 5 

Router(config-if)# ip verify source vlan 
dhcp-snooping [port-security]

Enables IP source guard, source IP address filtering on the port. The following are the command parameters:

vlan applies the feature to only specific VLANs on the interface. The dhcp-snooping option applies the feature to all VLANs on the interface that have DHCP snooping enabled.

port-security enables MAC address filtering. This feature is currently not supported.

Step 6 

Router(config-if)# exit

Returns to global configuration mode.

Step 7 

Router(config)# ip source binding mac_address 
vlan vlan-id ip-address interface interface_name

(Optional) Configures a static IP binding on the port.

Step 8 

Router(config)# end 

Exits configuration mode.

Step 9 

Router# show ip verify source [interface 
interface_name]

Verifies the configuration.


Note The static IP source binding can only be configured on a Layer 2 port. If you enter the ip source binding vlan interface command on a Layer 3 port, you receive this error message:

Static IP source binding can only be configured on switch port.
 
   

The no keyword deletes the corresponding IP source binding entry. This command requires an exact match of all the required parameters in order for the deletion to be successful.


This example shows how to enable per-Layer 2 port IP source guard on VLANs 10 through 20:

Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# ip dhcp snooping
Router(config)# ip dhcp snooping vlan 10 20
Router(config)# interface gigabitethernet 6/1
Router(config-if)# switchport mode access
Router(config-if)# switchport access vlan 10
Router(config-if)# no ip dhcp snooping trust
Router(config-if)# ip verify source vlan dhcp-snooping
Router(config-if)# end
Router# show ip verify source interface gigabitethernet 6/1
Interface  Filter-type  Filter-mode  IP-address       Mac-address        Vlan
---------  -----------  -----------  ---------------  -----------------  ----------
Gi6/1      ip           active       10.0.0.1                            10  
Gi6/1      ip           active       deny-all                            11-20  
Router#
 
   

The output shows that there is one valid DHCP binding to VLAN 10.

This example shows how to configure an interface to use prefer port mode:

Router# configure terminal
Router(config)# interface gigabitethernet 6/1
Router(config-if)# access-group mode prefer port
 
   

This example shows how to configure an interface to use merge mode:

Router# configure terminal
Router(config)# interface gigabitEthernet 6/1
Router(config-if)# access-group mode merge

Displaying IP Source Guard PACL Information

To display IP source guard PACL information for all interfaces on a switch, perform this task:

 
Command
Purpose
 
Router# show ip verify source [interface 
interface-name]

Displays IP source guard PACL information for all interfaces on a switch or for a specified interface.

This example shows that DHCP snooping is enabled on VLAN 10 through 20, interface fa6/1 is configured for IP filtering, and there is an existing IP address binding 10.0.01 on VLAN 10:

Router# show ip verify source interface fa6/1
Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/1      ip           active       10.0.0.1                         10
fa6/1      ip           active       deny-all                         11-20

Note The second entry shows that a default PACL (deny all IP traffic) is installed on the port for those snooping-enabled VLANs that do not have a valid IP source binding.


This example shows the displayed PACL information for a trusted port:

Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/2      ip           inactive-trust-port
 
   

This example shows the displayed PACL information for a port in a VLAN not configured for DHCP snooping:

Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/3      ip           inactive-no-snooping-vlan
 
   

This example shows the displayed PACL information for a port with multiple bindings configured for an IP/MAC filtering:

Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/4      ip           active       10.0.0.2         aaaa.bbbb.cccc  10
fa6/4      ip           active       11.0.0.1         aaaa.bbbb.cccd  11
fa6/4      ip           active       deny-all         deny-all        12-20
 
   

This example shows the displayed PACL information for a port configured for IP/MAC filtering but not for port security:

Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/5      ip           active       10.0.0.3         permit-all      10
fa6/5      ip           active       deny-all         permit-all      11-20
 
   

Note The MAC address filter shows permit-all because port security is not enabled, so the MAC filter cannot apply to the port/VLAN and is effectively disabled. Always enable port security first.


This example shows an error message when you enter the show ip verify source command on a port that does not have an IP source filter mode configured:

Router# show ip verify source interface fa6/6
IP Source Guard is not configured on the interface fa6/6.
 
   

This example shows how to display all interfaces on the switch that have IP source guard enabled:

Router# show ip verify source
Interface  Filter-type  Filter-mode  IP-address       Mac-address     Vlan
---------  -----------  -----------  ---------------  --------------  ---------
fa6/1      ip           active       10.0.0.1                         10
fa6/1      ip           active       deny-all                         11-20
fa6/2      ip           inactive-trust-port
fa6/3      ip           inactive-no-snooping-vlan
fa6/4      ip           active       10.0.0.2         aaaa.bbbb.cccc  10
fa6/4      ip           active       11.0.0.1         aaaa.bbbb.cccd  11
fa6/4      ip           active       deny-all         deny-all        12-20
fa6/5      ip           active       10.0.0.3         permit-all      10
fa6/5      ip           active       deny-all         permit-all      11-20

Displaying IP Source Binding Information

To display all IP source bindings configured on all interfaces on a switch, perform this task:

 
Command
Purpose
 
Router# show ip source binding [ip_address] 
[mac_address] [dhcp-snooping | static] 
[vlan vlan_id] [interface interface_name]

Displays IP source bindings using the optional specified display filters.

The dhcp-snooping filter displays all VLANs on the interface that have DHCP snooping enabled.

This example shows how to display all IP source bindings configured on all interfaces on the switch.

Router# show ip source binding
MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface
------------------  ---------------  ----------  -------------  ----  --------------------
00:02:B3:3F:3B:99   55.5.5.2         6522        dhcp-snooping  10    GigabitEthernet6/10
00:00:00:0A:00:0B   11.0.0.1         infinite    static         10    GigabitEthernet6/10
Router#
 
   

Table 76-1 describes the fields in the show ip source binding command output.

Table 76-1 show ip source binding Command Output 

Field
Description

MAC Address

Client hardware MAC address

IP Address

Client IP address assigned from the DHCP server

Lease (seconds)

IP address lease time

Type

Binding type; static bindings configured from CLI to dynamic binding learned from DHCP snooping

VLAN

VLAN number of the client interface

Interface

Interface that connects to the DHCP client host



Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum