Catalyst 2960 Switch Software Configuration Guide, Rel. 12.2(46)SE
Unsupported Commands in Cisco IOS Release 12.2(46)SE
Downloads: This chapterpdf (PDF - 113.0KB) The complete bookPDF (PDF - 13.68MB) | Feedback

Unsupported Commands in Cisco IOS Release 12.2(46)SE

Table Of Contents

Unsupported Commands in Cisco IOS Release 12.2(46)SE

Access Control Lists

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Route-Map Configuration Commands

Boot Loader Commands

Unsupported Global Configuration Commands

Debug Commands

Unsupported Privileged EXEC Commands

High Availability

SSO-Aware HSRP Commands

IGMP Snooping Commands

Unsupported Global Configuration Commands

Interface Commands

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

IP SLA

Unsupported MPLS Health Monitor Commands

Unsupported Ethernet Gatekeeper Registration Commands

Unsupported VoIP Call Setup Probe Commands

IPv6

IPv4-v6 Tunneling Commands

Layer 3

BGP

Other Unsupported BGP Commands

OSPF

VRF aware AAA

MAC Address Commands

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Miscellaneous

Unsupported User EXEC Commands

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Multicast

Unsupported BiDirectional PIM Commands

Unsupported Multicast Routing Manager Commands

Unsupported IP Multicast Rate Limiting Commands

Unsupported UDLR Commands

Unsupported Multicast Over GRE Commands

Network Address Translation (NAT) Commands

Unsupported Privileged EXEC Commands

QoS

Unsupported Global Configuration Command

Unsupported Interface Configuration Commands

Unsupported Policy-Map Configuration Command

RADIUS

Unsupported Global Configuration Commands

SNMP

Unsupported Global Configuration Commands

SNMPv3

Unsupported 3DES Encryption Commands

Spanning Tree

Unsupported Global Configuration Command

Unsupported Interface Configuration Command

VLAN

Unsupported Global Configuration Command

Unsupported vlan-config Command

Unsupported User EXEC Commands

VTP

Unsupported Privileged EXEC Commands


Unsupported Commands in Cisco IOS Release 12.2(46)SE


This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Catalyst 2960 switch prompt but are not supported in this release, either because they are not tested or because of Catalyst 2960 switch hardware limitations. This is not a complete list. These unsupported commands are listed by software feature and command mode:

Access Control Lists

Boot Loader Commands

Debug Commands

High Availability

IGMP Snooping Commands

Interface Commands

IP SLA

IPv6

Layer 3

MAC Address Commands

Miscellaneous

Multicast

Network Address Translation (NAT) Commands

QoS

RADIUS

SNMP

SNMPv3

Spanning Tree

VLAN

VTP

Access Control Lists

Unsupported Privileged EXEC Commands

access-enable [host] [timeout minutes]

access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]

clear access-template [access-list-number | name] [dynamic-name] [source] [destination].

show access-lists rate-limit [destination]

show accounting

show ip accounting [checkpoint] [output-packets | access violations]

show ip cache [prefix-mask] [type number]

Unsupported Global Configuration Commands

access-list rate-limit acl-index {precedence | mask prec-mask}

access-list dynamic extended

Unsupported Route-Map Configuration Commands

match ip address prefix-list prefix-list-name [prefix-list-name...]

Boot Loader Commands

Unsupported Global Configuration Commands

boot buffersize

Debug Commands

Unsupported Privileged EXEC Commands

debug platform cli-redirection main

debug platform configuration

High Availability

SSO-Aware HSRP Commands

All

IGMP Snooping Commands

Unsupported Global Configuration Commands

ip igmp snooping tcn

Interface Commands

Unsupported Privileged EXEC Commands

show interfaces [interface-id | vlan vlan-id] [crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape]

Unsupported Global Configuration Commands

interface tunnel

Unsupported Interface Configuration Commands

transmit-interface type number

ip igmp helper-address ip-address

IP SLA

Unsupported MPLS Health Monitor Commands

All

Unsupported Ethernet Gatekeeper Registration Commands

All

Unsupported VoIP Call Setup Probe Commands

All

IPv6

IPv4-v6 Tunneling Commands

All

Layer 3

BGP

All commands for these features:

BGP Support for Dual AS Configuration for Network AS Migrations

BGP Support for IP Prefix Import from Global Table into a VRF Table

BGP Support for Named Extended Community Lists

BGP Support for Sequenced Entries in Extended Community Lists

BGP Support for TTL Security Check

BGP Route-Map Policy List Support

BGP Next Hop Propagation

BGP Policy Accounting

BGP Policy Accounting output interface accounting

BGP Link Bandwidth

BGP Hybrid CLI Support

BGP Cost Community

BGP Dynamic Update Peer-Groups

BGP Conditional Route Injection

BGP Configuration Using Peer Templates

BGP Increased Support of Numbered as-path Access Lists to 500

Other Unsupported BGP Commands

address-family l2vpn

address-family vpnv4

bgp-policyclear bgp nsapaddress-family nsap

clear bgp nsap dampening

clear bgp nsap external

clear bgp nsap flap-statistics

clear bgp nsap peer-group

clear ip bgp ipv6

clear ip bgp l2vpn

clear ip bgp vpnv4

clear ip bgp vpnv6

ha-mode graceful-restartip extcommunity-list redistribute (BGP to ISO IS-IS)

ip policy-listredistribute (ISO IS-IS to BGP)

match extcommunity

neighbor ha-mode graceful-restart

neighbor sooredistribute dvmrp

neighbor ttl-securityset extcommunity

set extcommunity cost

show bgp nsap

show bgp nsap community

show bgp nsap community-list

show bgp nsap dampening

show bgp nsap dampened-paths

show bgp nsap filter-list

show bgp nsap flap-statistics

show bgp nsap inconsistent-as

show bgp nsap neighbors

show bgp nsap paths

show bgp nsap quote-regexp

show bgp nsap regexp

show bgp nsap summary

show ip bgp ipv4 multicast

show ip bgp ipv4 multicast summary

show ip bgp l2vpn

show ip bgp vpnv4

show ip extcommunity-list

show ip policy-list

OSPF

area sham-link

ignore lsa mospf

nsf ietf

nsf ietf helper disable

nsf ietf helper strict-lsa-checking

show ip ospf sham-links

VRF aware AAA

All

MAC Address Commands

Unsupported Privileged EXEC Commands

show mac-address-table

show mac-address-table address

show mac-address-table aging-time

show mac-address-table count

show mac-address-table dynamic

show mac-address-table interface

show mac-address-table multicast

show mac-address-table notification

show mac-address-table static

show mac-address-table vlan

show mac address-table multicast


Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.


Unsupported Global Configuration Commands

mac-address-table aging-time

mac-address-table notification

mac-address-table static

Miscellaneous

Unsupported User EXEC Commands

verify

Unsupported Privileged EXEC Commands

file verify auto

show cable-diagnostics prbs

test cable-diagnostics prbs

Unsupported Global Configuration Commands

errdisable recovery cause unicast flood

l2protocol-tunnel global drop-threshold

service compress-config

stack-mac persistent timer

Multicast

Unsupported BiDirectional PIM Commands

All

Unsupported Multicast Routing Manager Commands

All

Unsupported IP Multicast Rate Limiting Commands

All

Unsupported UDLR Commands

All

Unsupported Multicast Over GRE Commands

All

Network Address Translation (NAT) Commands

Unsupported Privileged EXEC Commands

show ip nat statistics

show ip nat translations

QoS

Unsupported Global Configuration Command

priority-list

Unsupported Interface Configuration Commands

priority-group

rate-limit

Unsupported Policy-Map Configuration Command

class class-default where class-default is the class-map-name.

RADIUS

Unsupported Global Configuration Commands

aaa nas port extended

aaa authentication feature default enable

aaa authentication feature default line

aaa nas port extended

radius-server attribute nas-port

radius-server configure

radius-server extended-portnames

SNMP

Unsupported Global Configuration Commands

snmp-server enable informs

snmp-server ifindex persist

SNMPv3

Unsupported 3DES Encryption Commands

All

Spanning Tree

Unsupported Global Configuration Command

spanning-tree pathcost method {long | short}

Unsupported Interface Configuration Command

spanning-tree stack-port

VLAN

Unsupported Global Configuration Command

vlan internal allocation policy {ascending | descending}

Unsupported vlan-config Command

private-vlan

Unsupported User EXEC Commands

show running-config vlan

show vlan ifindex

show vlan private-vlan

VTP

Unsupported Privileged EXEC Commands

vtp {password password | pruning | version number}


Note This command has been replaced by the vtp global configuration command.