Catalyst 2960 Switch Software Configuration Guide, 12.2(25)FX
Unsupported Commands in Cisco IOS Release 12.2(25)FX
Downloads: This chapterpdf (PDF - 158.0KB) The complete bookPDF (PDF - 7.97MB) | Feedback

Unsupported Commands in Cisco IOS Release 12.2(25)FX

Table Of Contents

Unsupported Commands in Cisco IOS Release 12.2(25)FX

Access Control Lists

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Debug Commands

Unsupported Privileged EXEC Commands

IGMP Snooping Commands

Unsupported Global Configuration Commands

Interface Commands

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

MAC Address Commands

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Miscellaneous

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Network Address Translation (NAT) Commands

Unsupported Privileged EXEC Commands

QoS

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

RADIUS

Unsupported Global Configuration Commands

SNMP

Unsupported Global Configuration Commands

Spanning Tree

Unsupported Global Configuration Command

Unsupported Interface Configuration Command

VLAN

Unsupported Global Configuration Commands

Unsupported vlan-config Command

Unsupported User EXEC Commands

VTP

Unsupported Privileged EXEC Commands


Unsupported Commands in Cisco IOS Release 12.2(25)FX


This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Catalyst 2960 switch prompt but are not supported in this release, either because they are not tested or because of Catalyst 2960 hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode.

Access Control Lists

Unsupported Privileged EXEC Commands

access-enable [host] [timeout minutes]

access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]

clear access-template [access-list-number | name] [dynamic-name] [source] [destination].

Unsupported Global Configuration Commands

access-list rate-limit acl-index {precedence | mask prec-mask}

access-list dynamic extended

Debug Commands

Unsupported Privileged EXEC Commands

debug platform cli-redirection main

debug platform configuration

IGMP Snooping Commands

Unsupported Global Configuration Commands

ip igmp snooping tcn

Interface Commands

Unsupported Privileged EXEC Commands

show interfaces [interface-id | vlan vlan-id] [crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape]

Unsupported Global Configuration Commands

interface tunnel

Unsupported Interface Configuration Commands

transmit-interface type number

MAC Address Commands

Unsupported Privileged EXEC Commands

show mac-address-table

show mac-address-table address

show mac-address-table aging-time

show mac-address-table count

show mac-address-table dynamic

show mac-address-table interface

show mac-address-table multicast

show mac-address-table notification

show mac-address-table static

show mac-address-table vlan

show mac address-table multicast


Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.


Unsupported Global Configuration Commands

mac-address-table aging-time

mac-address-table notification

mac-address-table static

Miscellaneous

Unsupported Privileged EXEC Commands

show cable-diagnostics prbs

test cable-diagnostics prbs

Unsupported Global Configuration Commands

errdisable recovery cause unicast flood

service compress-config

stack-mac persistent timer

Network Address Translation (NAT) Commands

Unsupported Privileged EXEC Commands

clear ip nat translation

show ip nat statistics

show ip nat translations

QoS

Unsupported Global Configuration Commands

priority-list

Unsupported Interface Configuration Commands

priority-group

RADIUS

Unsupported Global Configuration Commands

aaa nas port extended

radius-server attribute nas-port

radius-server configure

radius-server extended-portnames

SNMP

Unsupported Global Configuration Commands

snmp-server enable informs

snmp-server ifindex persist

Spanning Tree

Unsupported Global Configuration Command

spanning-tree pathcost method {long | short}

Unsupported Interface Configuration Command

spanning-tree stack-port

VLAN

Unsupported Global Configuration Commands

vlan internal allocation policy {ascending | descending}

Unsupported vlan-config Command

private-vlan

Unsupported User EXEC Commands

show running-config vlan

show vlan ifindex

show vlan private-vlan

VTP

Unsupported Privileged EXEC Commands

vtp {password password | pruning | version number}


Note This command has been replaced by the vtp global configuration command.