Cisco Nexus 1000V Series and Cisco VSG NX-OS System Messages Reference Guide for Microsoft Hyper-V
System Messages and Recovery Procedures for the Cisco Nexus 1000V, Cisco Cloud Services Platform, and Cisco VSG
Downloads: This chapterpdf (PDF - 3.5MB) The complete bookPDF (PDF - 5.11MB) | Feedback

System Messages and Recovery Procedures for the Cisco Nexus 1000V, Cisco Cloud Services Platform, and Cisco VSG

Table Of Contents

System Messages and Recovery Procedures for the Cisco Nexus 1000V, Cisco Cloud Services Platform, and Cisco VSG

AAA Messages

AAA-1

AAA-2

AAA-3

AAA-6

AAM Messages

AAM-2

AAM-3

ACLLOG Messages

ACLLOG-4

ACLLOG-6

ACLMGR Messages

ACLMGR-2

ACLMGR-3

ACLMGR-4

ACLMGR-6

ACLQOS Messages

ACLQOS-SLOT#-2

ACLQOS-SLOT#-3

ACLQOS-SLOT#-4

ACLQOS-SLOT#-5

ACLTCAM Messages

ACLTCAM-2

ACLTCAM-3

ACLTCAM-4

ACLTCAM-6

ACL Messages

ACL-2

ACL-3

ACL-4

ACL-5

ACL-6

AMM-SLOT#-0

AMM-SLOT#-2

AMM-SLOT#-6

ASSOC_MGR-0

ASSOC_MGR-1

ASSOC_MGR-2

ASSOC_MGR-3

ASSOC_MGR-4

ASSOC_MGR-5

ASSOC_MGR-6

ASSOC_MGR-7

BFDC Messages

BFDC-SLOT#-2

BFD Messages

BFD-3

BFD-4

BFD-5

BFD-6

BIOS_DAEMON Messages

BIOS_DAEMON-2

BIOS_DAEMON-5

BIOS_DAEMON-SLOT#-2

BIOS_DAEMON-SLOT#-5

BOOTUP_TEST Messages

BOOTUP_TEST-2

BOOTVAR Messages

BOOTVAR-2

BOOTVAR-3

BOOTVAR-5

BOOTVAR-6

CALLHOME Messages

CALLHOME-2

CALLHOME-3

CALLHOME-6

CDP Messages

CDP-2

CDP-3

CDP-4

CDP-5

CDP-6

CERT_ENROLL Messages

CERT_ENROLL-2

CERT_ENROLL-3

CERT_ENROLL-6

CFS Messages

CFS-2

CFS-3

CFS-4

CFS-6

CIMSRVPROV Messages

CIMSRVPROV-2

CIMSRVPROV-3

CIMSRVPROV-6

CLIS Messages

CLIS-5

CLOUD Messages

CLOUD-2

CLOUD-3

CLOUD-6

CLUSTER Messages

CLUSTER-2

CMOND Messages

CMOND-2

CMPPROXY Messages

CMPPROXY-2

CMPPROXY-5

CMPPROXY-6

COPP Messages

COPP-1

COPP-2

COPP-3

COPP-4

COPP-5

COPP-6

COPP-7

CPPA_MGR Messages

CPPA_MGR-3

CPPA_MGR-5

CREDITMON Messages

CREDITMON-SLOT#-2

CTS Messages

CTS-2

CTS-3

CTS-5

CTS-6

DCEFIB Messages

DCEFIB-SLOT#-0

DCEFIB-SLOT#-2

DCEFIB-SLOT#-6

DEBUGPROXY Messages

DEBUGPROXY-6

DEVICE_TEST Messages

DEVICE_TEST-2

DEVICE_TEST-3

DEVICE_TEST-4

DEVICE_TEST-5

DEVICE_TEST-6

DEV_LOG Messages

DEV_LOG-3

DEV_LOG-SLOT#-4

DFTM Messages

DFTM-SLOT#-2

DFTM-SLOT#-3

DHCP_SNOOP Messages

DHCP_SNOOP-2

DHCP_SNOOP-3

DHCP_SNOOP-4

DHCP_SNOOP-5

DHCP_SNOOP-6

DIAGCLIENT Messages

DIAGCLIENT-2

DIAGCLIENT-3

DIAGCLIENT-4

DIAGCLIENT-5

DIAGMGR Messages

DIAGMGR-2

DIAGMGR-3

DIAGMGR-4

DIAGMGR-5

DIAGMGR-6

DIAG_PORT_LB Messages

DIAG_PORT_LB-2

DIAG_PORT_LB-3

DIAG_PORT_LB-4

DIAG_PORT_LB-5

DMM Messages

DMM-SLOT#-5

DOT1X Messages

DOT1X-2

DOT1X-3

DOT1X-4

DOT1X-5

DPP_DEBUG Messages

DPP_DEBUG-2

DPVM Messages

DPVM-2

DPVM-3

DPVM-4

DPVM-6

DSTATS Messages

DSTATS-2

DSTATS-3

ELTMC Messages

ELTMC-SLOT#-2

ELTM Messages

ELTM-2

ELTM-5

ELTM-6

EOU Messages

EOU-2

EOU-5

EOU-6

EOU-7

EPLD_UPGRADE Messages

EPLD_UPGRADE-2

EPP Messages

EPP-5

ETHPORT Messages

ETHPORT-2

ETHPORT-3

ETHPORT-4

ETHPORT-5

ETH_PORT_CHANNEL Messages

ETH_PORT_CHANNEL-1

ETH_PORT_CHANNEL-2

ETH_PORT_CHANNEL-3

ETH_PORT_CHANNEL-4

ETH_PORT_CHANNEL-5

ETH_PORT_CHANNEL-6

ETH_PORT_CHANNEL-7

EUREKA_USD Messages

EUREKA_USD-3

EVMC Messages

EVMC-3

EVMC-4

EVMC-5

EVMS Messages

EVMS-2

EVMS-4

EVMS-6

EXCEPTIONLOG Messages

EXCEPTIONLOG-SLOT#-2

FABRICPATH Messages

FABRICPATH-2

FABRICPATH-4

FABRICPATH-6

FCC_LC Messages

FCC_LC-2

FCC_LC-5

FCC_LC-6

FCC Messages

FCC-2

FCC-5

FCC-6

FCDDH Messages

FCDDH-SLOT#-3

FCDDH-SLOT#-4

FCDDH-SLOT#-5

FCDD Messages

FCDD-SLOT#-3

FCDD-SLOT#-4

FCDD-SLOT#-5

FCDD-SLOT#-7

FCDOMAIN Messages

FCDOMAIN-2

FCDOMAIN-3

FCDOMAIN-4

FCDOMAIN-5

FCDOMAIN-6

FCDOMAIN-7

FCD Messages

FCD-7

FCFWD Messages

FCFWD-3

FCFWD-4

FCFWD-6

FCNS Messages

FCNS-2

FCNS-3

FCNS-4

FCNS-6

FCOE_MGR Messages

FCOE_MGR-2

FCOE_MGR-5

FCS Messages

FCS-2

FCS-3

FCS-5

FCS-6

FDMI Messages

FDMI-2

FDMI-3

FDMI-4

FDMI-6

FEX Messages

FEX-2

FEX-5

FICON Messages

FICON-2

FICON-3

FICON-5

FICON-6

FLEXLINK Messages

FLEXLINK-2

FLEXLINK-5

FLOGI Messages

FLOGI-1

FLOGI-2

FLOGI-4

FLOGI-5

FSCM Messages

FSCM-2

FSPF Messages

FSPF-2

FSPF-3

FSPF-4

FSPF-5

FSPF-6

FSPF-7

FWM Messages

FWM-0

FWM-1

FWM-2

FWM-3

FWM-4

FWM-6

GLBP Messages

GLBP-2

GLBP-3

GLBP-4

GLBP-5

HSRP_ENGINE Messages

HSRP_ENGINE-3

HSRP_ENGINE-4

HSRP_ENGINE-5

HSRP_ENGINE-6

IKE Messages

IKE-3

IKE-4

IKE-6

ILC_HELPER Messages

ILC_HELPER-2

ILC_HELPER-3

ILC_HELPER-6

IMAGE_DNLD Messages

IMAGE_DNLD-SLOT#-2

IMAGE_DNLD-SLOT#-4

IMAGE_DNLD-SLOT#-5

IMAGE_UPGRADE Messages

IMAGE_UPGRADE-SLOT#-2

IMAGE_UPGRADE-SLOT#-4

IM Messages

IM-3

IM-5

INTERFACE_VLAN Messages

INTERFACE_VLAN-4

INTERFACE_VLAN-5

IOA_LC Messages

IOA_LC-5

IPACL Messages

IPACL-0

IPACL-1

IPACL-2

IPACL-3

IPACL-4

IPACL-5

IPACL-6

IPFC Messages

IPFC-2

IPFC-3

IPFC-5

IPFC-6

IPPOOL Messages

IPPOOL-3

IPPOOL-5

IPQOSMGR Messages

IPQOSMGR-2

IPQOSMGR-3

IPQOSMGR-4

IPQOSMGR-5

IPQOSMGR-6

IPQOSMGR-SLOT#-3

IPSEC Messages

IPSEC-2

IPSEC-3

IPSEC-5

IPS_SB_MGR Messages

IPS_SB_MGR-SLOT#-2

IPS_SB_MGR-SLOT#-3

IPS_SB_MGR-SLOT#-4

IPS_SB_MGR-SLOT#-6

IPS Messages

IPS-2

IPS-3

IPS-4

IPS-5

IPS-6

IPS-7

IPV6 Messages

IPV6-2

IPV6-3

IPV6-4

IPV6-6

IP Messages

IP-1

IP-2

IP-3

IP-4

IP-6

ISAPI Messages

ISAPI-SLOT#-0

ISAPI-SLOT#-1

ISAPI-SLOT#-2

ISAPI-SLOT#-3

ISAPI-SLOT#-4

ISAPI-SLOT#-5

ISAPI-SLOT#-6

ISAPI-SLOT#-7

ISNS Messages

ISNS-2

IVR Messages

IVR-2

IVR-3

IVR-4

IVR-5

IVR-6

IVR-7

L2FMC Messages

L2FMC-SLOT#-0

L2FMC-SLOT#-2

L2FMC-SLOT#-5

L2FMC-SLOT#-6

L2FM Messages

L2FM-0

L2FM-1

L2FM-2

L2FM-4

L2FM-6

L2MCAST Messages

L2MCAST-SLOT#-0

L2MCAST-SLOT#-2

L2MCAST-SLOT#-6

L3VM Messages

L3VM-5

LACP Messages

LACP-3

LACP-5

LC_CFG Messages

LC_CFG-SLOT#-2

LC_PORT_CHANNEL Messages

LC_PORT_CHANNEL-SLOT#-0

LC_PORT_CHANNEL-SLOT#-3

LC_PORT_MGR Messages

LC_PORT_MGR-SLOT#-2

LC_RDL Messages

LC_RDL-3

LC_RDL-6

LDAP Messages

LDAP-2

LDAP-3

LDAP-5

LDAP-6

LDP-5

LIBBASE_SVC Messages

LIBBASE_SVC-2

LIBBASE_SVC-4

LIBBASE_SVC-5

LIBGD Messages

LIBGD-2

LIBGD-3

LIBGD-5

LIBGD-6

LICMGR Messages

LICMGR-0

LICMGR-1

LICMGR-2

LICMGR-3

LICMGR-4

LICMGR-6

LLDP Messages

LLDP-3

LLDP-5

LLDP-6

MAC Messages

MAC-SLOT#-2

MCAST Messages

MCAST-2

MCAST-4

MCAST-5

MCECTEST Messages

MCECTEST-3

MCECTEST-5

MCECTEST-6

MCM Messages

MCM-2

MCM-5

MCM-6

MFDM Messages

MFDM-2

MODULE Messages

MODULE-2

MODULE-3

MODULE-4

MODULE-5

MODULE-6

MONITOR Messages

MONITOR-3

MONITOR-4

MONITOR-5

NFM Messages

NFM-2

NFM-3

NFM-4

NFM-5

NFM-6

NFM-7

NFP Messages

NFP-SLOT#-2

NFP-SLOT#-5

NOHMS Messages

NOHMS-2

NPC Messages

NPC-SLOT#-3

NPC-SLOT#-4

NPC-SLOT#-5

NPV Messages

NPV-2

NPV-3

NPV-4

NPV-5

NPV-6

NPV-7

NSMGR Messages

NSMGR-3

NSMGR-5

NTP Messages

NTP-2

NTP-3

NTP-6

NVP Messages

NVP-6

NVP-SLOT#-2

OC_USD Messages

OC_USD-2

ORI_FWD Messages

ORI_FWD-2

ORI_FWD-6

ORI_MAC Messages

ORI_MAC-2

ORI_MAC-6

OTM Messages

OTM-2

OTM-3

OTM-5

OTM-6

PFMA Messages

PFMA-0

PFMA-1

PFMA-2

PFMA-3

PFMA-4

PFMA-5

PFMA-7

PHY_USD Messages

PHY_USD-SLOT#-4

PIXM Messages

PIXM-2

PIXM-3

PIXM-4

PIXM-7

PLATFORM Messages

PLATFORM-0

PLATFORM-1

PLATFORM-2

PLATFORM-3

PLATFORM-4

PLATFORM-5

PLATFORM-6

PLATFORM-7

PLOG_SUP Messages

PLOG_SUP-4

PLOG Messages

PLOG-4

POLICY_ENGINE Messages

POLICY_ENGINE-5

POLICY_ENGINE-6

PONG Messages

PONG-5

PORT Messages

PORT-2

PORT-3

PORT-4

PORT-5

PRIVATE_VLAN Messages

PRIVATE_VLAN-2

PRIVATE_VLAN-3

PRIVATE_VLAN-4

PRIVATE_VLAN-5

PROC_MGR Messages

PROC_MGR-SLOT#-2

PROC_MGR-SLOT#-3

PROC_MGR-SLOT#-4

PROC_MGR-SLOT#-6

PSS Messages

PSS-0

PSS-1

PSS-2

PSS-4

PSS-5

PTPLC Messages

PTPLC-3

PTP Messages

PTP-5

PTP-6

QOS Messages

QOS-2

QOS-3

QOS-4

QOS-6

RADIUS Messages

RADIUS-2

RADIUS-3

RADIUS-4

RADIUS-5

RADIUS-6

RDL Messages

RDL-2

RDL-3

RDL-6

RES_MGR Messages

RES_MGR-1

RES_MGR-2

RES_MGR-3

RES_MGR-4

RES_MGR-5

RES_MGR-6

RIB Messages

RIB-0

RIB-1

RIB-2

RIB-3

RIB-4

RIB-5

RIB-6

RLIR Messages

RLIR-2

RLIR-6

RM Messages

RM-6

RM-SLOT#-2

RM-SLOT#-4

RSCN Messages

RSCN-2

RSCN-4

RSCN-6

SAL Messages

SAL-5

SAN_EXT_TUNER Messages

SAN_EXT_TUNER-3

SATCTRL Messages

SATCTRL-4

SATCTRL-SLOT#-2

SATCTRL-SLOT#-4

SATCTRL-SLOT#-5

SCHEDULER Messages

SCHEDULER-2

SCHEDULER-3

SCHEDULER-4

SCHEDULER-6

SCM Messages

SCM-2

SDV Messages

SDV-2

SDV-3

SDV-4

SDV-6

SDV-7

SECURITYD Messages

SECURITYD-2

SECURITYD-3

SECURITYD-5

SECURITYD-6

SEG_BD Messages

SEG_BD-2

SEG_BD-3

SEG_BD-5

SENSOR_USD Messages

SENSOR_USD-2

SENSOR_USD-3

SENSOR_USD-5

SFC Messages

SFC-3

SFM Messages

SFM-2

SFM-6

SIFMGR Messages

SIFMGR-2

SKSD Messages

SKSD-2

SKSD-3

SKSD-4

SKSD-5

SKSD-6

SKT_USD Messages

SKT_USD-3

SKT_USD-6

SME_CPP Messages

SME_CPP-2

SME_CPP-3

SME_CPP-5

SME_CPP-SLOT#-2

SME_CPP-SLOT#-3

SME_CPP-SLOT#-4

SNMPD Messages

SNMPD-1

SNMPD-2

SNMPD-3

SNMPD-4

SNMPD-5

SNMPD-6

SNMPD-7

SPAN Messages

SPAN-2

SPAN-3

SPAN-5

SPAN-6

SPI Messages

SPI-SLOT#-2

STP Messages

STP-2

STP-3

STP-4

STP-6

SVC_BATTERY Messages

SVC_BATTERY-SLOT#-2

SVC_BATTERY-SLOT#-4

SVC_BATTERY-SLOT#-6

SVC Messages

SVC-0

SVC-1

SVC-2

SVC-3

SVC-4

SVC-5

SVC-6

SVC-7

SYSMGR Messages

SYSMGR-2

SYSMGR-3

SYSMGR-4

SYSMGR-5

SYSMGR-6

SYSMGR-7

SYSTEMHEALTH Messages

SYSTEMHEALTH-2

SYSTEMHEALTH-4

SYSTEMHEALTH-5

SYSTEMHEALTH-6

TACACS Messages

TACACS-2

TACACS-3

TACACS Messages

TACACS-4

TACACS-5

TACACS-6

TBIRD_CMN_USD Messages

TBIRD_CMN_USD-6

TBIRD_FWD_USD Messages

TBIRD_FWD_USD-6

TBIRD_MAC_USD Messages

TBIRD_MAC_USD-3

TBIRD_MAC_USD-6

TBIRD_QUE_USD Messages

TBIRD_QUE_USD-6

TBIRD_XBAR_USD Messages

TBIRD_XBAR_USD-6

TCAP Messages

TCAP-2

TPC Messages

TPC-SLOT#-5

TTYD Messages

TTYD-2

TTYD-3

TTYD-6

TUNNEL Messages

TUNNEL-2

TUNNEL-3

TUNNEL-4

TUNNEL-5

TUNNEL-7

U2RIB Messages

U2RIB-2

U2RIB-3

U2RIB-5

U2RIB-6

UDLD Messages

UDLD-3

UDLD-4

UDLD-5

UFDM Messages

UFDM-2

VDC_MGR Messages

VDC_MGR-2

VDC_MGR-3

VDC_MGR-5

VEC Messages

VEC-SLOT#-3

VEC-SLOT#-4

VEC-SLOT#-5

VEDB_MGR Messages

VEDB_MGR-2

VEDB_MGR-6

VEM_MGR Messages

VEM_MGR-2

VEM_MGR-3

VEM_MGR-5

VEM_MGR-6

VEM_MGR-SLOT#-1

VEM_MGR-SLOT#-5

VES Messages

VES-SLOT#-4

VES-SLOT#-5

VFC Messages

VFC-3

VFC-6

VIM Messages

VIM-2

VIM-3

VIM-4

VIM-5

VLAN_MGR Messages

VLAN_MGR-2

VLAN_MGR-3

VLAN_MGR-4

VLAN_MGR-5

VLAN_MGR-6

VMM Messages

VMM-2

VMS Messages

VMS-2

VMS-3

VMS-5

VNI Messages

VNI-2

VNI-3

VNI-6

VNS_AGENT Messages

VNS_AGENT-2

VNS_AGENT-3

VNS_AGENT-5

VNS_AGENT-6

VNS_AGENT-7

VPC Messages

VPC-2

VPC-3

VPC-4

VPC-5

VPC-6

VPM Messages

VPM-2

VPM-3

VPM-4

VPM-6

VPM-SLOT#-2

VSAN Messages

VSAN-2

VSAN-3

VSAN-6

VSD Messages

VSD-SLOT#-2

VSHD Messages

VSHD-2

VSHD-3

VSHD-4

VSHD-5

VSHD-7

WWN Messages

WWN-1

WWN-2

WWN-3

WWN-4

WWN-5

WWN-6

WWN-7

XBAR_CLIENT Messages

XBAR_CLIENT-2

XBAR_CLIENT-3

XBAR_CLIENT-SLOT#-2

XBAR_CLIENT-SLOT#-3

XBAR Messages

XBAR-2

XBAR-3

XBAR-5

XMLMA Messages

XMLMA-2

XMLMA-3

XMLMA-5

XMLMA-6

XMLSA Messages

XMLSA-2

XMLSA-5

XMLSA-6

ZBM Messages

ZBM-2

ZBM-4

ZBM-6

ZONE Messages

ZONE-2

ZONE-3

ZONE-4

ZONE-5

ZONE-6


System Messages and Recovery Procedures for the Cisco Nexus 1000V, Cisco Cloud Services Platform, and Cisco VSG


This chapter includes system messages for the Cisco NX-OS Nexus1000V, Cisco Cloud Services Platform (Nexus 1010), and Cisco VSG. The messages are listed in alphabetical order by the system facility that produces them. Within each system facility section, messages are listed alphabetically by severity and mnemonics. Each error message is followed by an explanation and a recommended action.

AAA Messages

AAA-1

Error Message      AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request rejected as maximum aaa 
sessions are in progress 

Explanation    Aaa request rejected as the limit for maximum concurrent aaa sessions is reached

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

AAA-2

Error Message      AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. 
[chars] 

Explanation    Upgrading of accounting log failed.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting: [chars] 

Explanation    Aaa daemon is exiting.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

AAA-3

Error Message      AAA-3-AAA_NVRAMFAILURE: nvram failure 

Explanation    Nvram can not be read/written to. Hence accounting log can not be stored there

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

AAA-6

Error Message      AAA-6-AAA_ACCOUNTING_MESSAGE: [chars] 

Explanation    Accounting Message

Recommended Action    No action is required.

AAM Messages

AAM-2

Error Message      AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED: Failed to lookup global port 
index for interface [[chars]] 

Explanation    Failed to lookup global port index for interface [chars]

Recommended Action    No action is required.

AAM-3

Error Message      AAM-3-ALLOC_FAILED: Failed in File:[chars] Line:[dec] for type [dec] 
size [dec] 

Explanation    AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec]

Recommended Action    No action is required.

Error Message      AAM-3-ASSERTION_FAILED: Failed in File:[chars] Line:[dec] 

Explanation    AAM Process assertion failed in File:[chars], at line:[dec]

Recommended Action    No action is required.

ACLLOG Messages

ACLLOG-4

Error Message      ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars] 

Explanation    Max flow reached in current interval: [chars]

Recommended Action    No action is required.

Error Message      ACLLOG-4-ACLLOG_THRESHOLD: [chars] 

Explanation    Threshold Reached for Flow: [chars]

Recommended Action    No action is required.

ACLLOG-6

Error Message      ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars] 

Explanation    Flow info in current alert interval: [chars]

Recommended Action    No action is required.

Error Message      ACLLOG-6-ACLLOG_NEW_FLOW: [chars] 

Explanation    New Acllog Flow: [chars]

Recommended Action    No action is required.

ACLMGR Messages

ACLMGR-2

Error Message      ACLMGR-2-ACLMGR_ABORT_FAIL: Abort failed: client %llX, [chars] 

Explanation    The PPF abort failed

Recommended Action    No action is required.

Error Message      ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on interface [chars] 
([hex]) allowed to succeed in spite of access-list failure 

Explanation    Although an access-list operation failed during a port event, the port event still finished successfully because errdisable is disallowed

Recommended Action    No action is required.

Error Message      ACLMGR-2-EXITING: Exit reason: [chars] 

Explanation    The ACLMGR service process has exited due to [char]. The process has probably been restarted automatically.

Recommended Action    No action is required.

Error Message      ACLMGR-2-INITFAIL: ACLMGR Service Init failed: [chars] 

Explanation    ACLMGR Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      ACLMGR-2-MALLOC_ERROR: Size [dec] bytes 

Explanation    The ACLMGR service could not allocate memory.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      ACLMGR-2-PSS_ERROR: [chars]: PSS ret. val=[dec] 

Explanation    The ACLMGR service encountered error while operating on a persistent storage database.

Recommended Action    No action is required.

ACLMGR-3

Error Message      ACLMGR-3-ACLMGR_ACL_ON_FAB_INACTIVE: ACL on FEX fabric interface not 
activated 

Explanation    ACL applied to a FEX fabric port or port-channel is not activated

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel 
bound interface not activated 

Explanation    ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric portchannel

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_COMMIT_FAIL: Commit failed: client %llX, [chars] 

Explanation    The PPF commit failed

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], 
session 0x%llx, type: [chars] 

Explanation    ACL PPF database lock acquire/release related message.

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars] 

Explanation    The PPF generated error

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found corrupted 

Explanation    The ACLMGR service has detected corruption in one of its persistent information database. The database would be recreated.

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL statistic parsing or 
consolidation failed 

Explanation    A statistic update failed during the parsing or consolidation step; statistics may have been lost

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection 
to interface [chars] ([hex]) disabled: the port has been removed 

Explanation    A VACL redirection to the port has been deactivated because the port has been removed

Recommended Action    No action is required.

Error Message      ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed: client %llX, [chars] 

Explanation    The PPF Verify failed

Recommended Action    No action is required.

Error Message      ACLMGR-3-MTSERROR: [chars] 

Explanation    ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occured.

Recommended Action    No action is required.

ACLMGR-4

Error Message      ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning: [chars] 

Explanation    The PPF generated warning

Recommended Action    No action is required.

Error Message      ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to 
interface [chars] ([hex]) disabled: the port became a portchannel member 

Explanation    A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel

Recommended Action    No action is required.

Error Message      ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec] 

Explanation    There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    No action is required.

ACLMGR-6

Error Message      ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification: [chars] 

Explanation    The PPF generated notification

Recommended Action    No action is required.

Error Message      ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby mode 

Explanation    The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    No action is required.

Error Message      ACLMGR-6-BECAME_STDBY: Became STANDBY from active mode 

Explanation    The ACLMGR service became standby from active mode.

Recommended Action    No action is required.

Error Message      ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to 
system manager: Reason=[chars] 

Explanation    The ACLMGR service was unable to send heartbeat to the system manger

Recommended Action    No action is required.

Error Message      ACLMGR-6-SERVICE_UP: Initialized [chars] 

Explanation    The ACLMGR service is up and ready The service was initialized in [char] mode.

Recommended Action    No action is required.

Error Message      ACLMGR-6-SRVEXIT: ACLMGR Service shutting down gracefully 

Explanation    ACLMGR Service is shutting down gracefully. This is an informational message.

Recommended Action    No action is required.

Error Message      ACLMGR-6-SWITCHOVER: Switching Over to other Sup. 

Explanation    The ACLMGR service has successfully switched over to the standby supervisor card.

Recommended Action    No action is required.

ACLQOS Messages

ACLQOS-SLOT#-2

Error Message      ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure: [chars] 

Explanation    ACLQOS operation failed in the aclqos client

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE: Inband interface lif 
lookup failed ([chars]) 

Explanation    Inband interface lif lookup failed

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory allocation failed. 
[chars] 

Explanation    Memory allocation failed. This is a critical failure

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource exhausted: [chars] 

Explanation    Tcam resources to program acls exhausted

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-2-PPF_FAILED: Database failure: [chars] 

Explanation    Database operation failed in the aclqos client

Recommended Action    No DDTS.

ACLQOS-SLOT#-3

Error Message      ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control 
parameters: [chars] 

Explanation    Invalid Congestion Control parameters

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-3-ACLQOS_MCM_ERROR: MCM Message Inconsistent. Please 
collect MCM and ACLMgr Tech Support for all VDCs 

Explanation    MCM Message Inconsistent

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parameters: 
[chars] 

Explanation    Invalid Pause parameters

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS queuing error: [chars] 

Explanation    Internal error in ACL/QoS queuing config

Recommended Action    No DDTS.

ACLQOS-SLOT#-4

Error Message      ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars] 

Explanation    Tcam will be overused, please turn off atomic update

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_FC_WARNING: Found stale FCoE entry in instance 
[dec]. VSAN: [dec], SID: [hex], DID: [hex], SI:[dec], SI_MASK:[dec], RW_VSAN: 
[dec], RW_VSAN_FLAG: [dec], RW_SID: [hex], RW_SID_FLAG: [dec], RW_DID: [hex]. 
RW_DID_FLAG: [dec] Cleaning it up. 

Explanation    Found stale FCoE entry in instance [dec]. VSAN: [dec], SID: 0x[hex], DID: 0x[hex], SI:[dec], SI_MASK:[dec], RW_VSAN:[dec], RW_VSAN_FLAG: [dec], RW_SID: 0x[hex], RW_SID_FLAG:[dec], RW_DID: 0x[hex]. RW_DID_FLAG: [dec] Cleaning it up.

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_MATCH_ALL_MERGE_UPDATE: Warning (match_all 
merging): [chars] 

Explanation    Warning (match_all merging)

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Tcam [dec] Bank 
[dec]susagehasreacheditsthreshold'

Explanation    Tcam is almost full

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID: ACL/QoS invalid queuing 
policy because of cos map change: [chars] queue [chars], interface [chars] 

Explanation    Attemped to configure an invalid queuing policy

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS invalid queuing 
policy: [chars] 

Explanation    Attemped to configure an invalid queuing policy

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec] Bank 
[dec]susageisbelowthethresholdnow'

Explanation    Tcamsusageisbelowthethreshold'

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-4-ACLQOS_WARNING: ACLQOS Warning: [chars] 

Explanation    ACLQOS Warnings

Recommended Action    No DDTS.

ACLQOS-SLOT#-5

Error Message      ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE: Disruptive update of 
IPv6 compression entries 

Explanation    Disruptive IPv6 compression entries update

Recommended Action    No DDTS.

Error Message      ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic ACL/QoS policy update 
done for [chars] 

Explanation    Non atomic ACL/QoS policy update was done

Recommended Action    No DDTS.

ACLTCAM Messages

ACLTCAM-2

Error Message      ACLTCAM-2-ACL_TCAM_ADJ_EXHAUSTED: ACLTCAM failed to program route 
for VSAN: [dec], SID: [chars] DID: [chars], error: [chars]. 

Explanation    ACLTCAM process experienced a failure while programming route for VSAN [dec] SID [chars] DID [chars] due to resource exhaustion. [chars] is the error code.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to FULL. [chars] TCAM 
Usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars] 

Explanation    [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars]

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED: [chars] [dec], 
Error: [hex]. 

Explanation    Unable to read configuration from forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED: [chars] [dec], 
Error: [hex]. 

Explanation    Unable to write configuration to forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_FLOW_STATS_READ_FAILED: Hardware flow stats read 
failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]). 

Explanation    Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found 
inconsistent. 

Explanation    Database found inconsistent.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found 
inconsistent. 

Explanation    TCAM contents are found inconsistent.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization failed for forwarding 
engine ASIC: [dec], [chars] TCAM. 

Explanation    Initialization failed for forwarding engine ASIC [dec], in [chars] TCAM.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED: Initialization failed for 
forwarding engine ASIC: [dec], [chars] TCAM, [chars] Region. 

Explanation    Initialization of regions failed for forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory allocation failed for size 
[dec]. 

Explanation    Memory allocation is failed for size [dec] bytes.

Recommended Action    Restart the process.

Error Message      ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars]. 

Explanation    MTS operation failed. [chars] is the reason.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_MTS_Q_FULL: MTS queue for SAP [dec] is full 

Explanation    MTS queue for SAP [dec] is full

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed 
for opCode: [dec]. 

Explanation    MTS registration failed for opCode: [dec].

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get route for VSAN: 
[dec], Rewrite: [chars] DID: [chars] DID MASK: [chars], error: [hex]. 

Explanation    ACLTCAM process experienced a failure while getting route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars]. [hex] is the error code.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource exhausted for 
interface : [chars] 

Explanation    ACLTCAM hardware resource is completely used.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars] read from hardware 
TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]). 

Explanation    [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID: Invalid([chars], value: 
[dec]) TCAM entry read from hardware TCAM (FWD-Engine: [dec], [chars] TCAM, 
Address: [dec]), Ignoring this entry. 

Explanation    Invalid([chars], value: [dec]) TCAM entry from hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec]) Ignoring this entry

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars] write to hardware 
TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]). 

Explanation    [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message      ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], 
reason: [hex]. 

Explanation    Failed to do PSS operation [chars]. [hex] is the reason.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed - [hex]. 

Explanation    Persistent database handle could not obtained for ACLTCAM. [hex] is the error.

Recommended Action    No action is required.

Error Message      ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM contents failed 
during upgrade - [hex]. 

Explanation    During non-disruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.

Recommended Action    No action is required.

ACLTCAM-3

Error Message      ACLTCAM-3-ACL_TCAM_INV_TCAM_SYNC_ATTEMPT: Attempt to write invalid 
shadow entry: [dec] ([dec]/[dec]) to TCAM, fwd-engine: [dec] ([chars]), 
change-array: [dec]/[dec], <MSG_EXPL

Explanation    TL Port Manager initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-ACL_TCAM_MTS_Q_LEAK: Possible MTS buffer leak for SAP [dec] 

Explanation    Possible MTS buffer leak for SAP [dec]

Recommended Action    No action is required.

Error Message      ACLTCAM-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    TL Port Manager is out of dynamic memory. [chars] specifies the context where the failure occured.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-FC2ERROR: [chars] 

Explanation    TL Port Manager encountered an FC2 error. [chars] specifies the context where the error occured.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-GENERROR: [chars] 

Explanation    TL Port Manager encountered a general error, one that does not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-MTSERROR: [chars] 

Explanation    TL Port Manager encountered an MTS error. [chars] specifies the context where the error occured.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-PSSERROR: [chars] 

Explanation    TL Port Manager encountered a PSS error. [chars] specifies the context where the failure occured.

Recommended Action    No action is required.

Error Message      ACLTCAM-3-REGISTER_FAILED: Could not register to MTS opcode [chars] 
- error [hex]. 

Explanation    ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.

Recommended Action    No action is required.

ACLTCAM-4

Error Message      ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) 
fell below [dec]% fwd-eng: [dec], [chars] 

Explanation    [chars] TCAM usage [dec]/[dec] fell below [dec] percent on fwd-engine [dec], [chars]

Recommended Action    No action is required.

Error Message      ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM usage 
([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars] 

Explanation    [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars]

Recommended Action    No action is required.

Error Message      ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow counter for flow: 
vsan: [dec], sid: [hex], did: [hex] with statistics: frames = %llu & bytes = %llu 
was invalidated due to: [chars] 

Explanation    ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [[chars]].

Recommended Action    No action is required.

Error Message      ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow counter for flow: 
vsan: [dec], sid: [hex], did: [hex] is now valid 

Explanation    ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].

Recommended Action    No action is required.

Error Message      ACLTCAM-4-ACL_TCAM_MTS_Q_HIGH: MTS queue for SAP [dec] is close to 
full 

Explanation    MTS queue for SAP [dec] is close to full

Recommended Action    No action is required.

Error Message      ACLTCAM-4-TLPM_ALPA_CACHE_FULL: Translation Port ALPA cache is full. 
Some new entries may not be cached 

Explanation    TL Port cache is currently fully populated with active entries. Hence, there is no available cache space to be assigned any newly created alpa entry on a TL Port. This is an informational message.

Recommended Action    No action is required.

ACLTCAM-6

Error Message      ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars]. 

Explanation    ACLTCAM status is reported as: [chars].

Recommended Action    No action is required.

Error Message      ACLTCAM-6-MGRCREATED: Translation Port Manager created. 

Explanation    TL Port Manager was created successfully and is up and running. This is an informational message.

Recommended Action    No action is required.

Error Message      ACLTCAM-6-MGREXIT: Translation Port Manager shutting down 
gracefully. 

Explanation    TL Port Manager is shutting down gracefully. This is an informational message.

Recommended Action    No action is required.

Error Message      ACLTCAM-6-PORTDOWN: Translation Port [chars] DOWN. 

Explanation    A port configured as TL Port is DOWN and out of operation. [chars] is the interface-id string that identifies the TL Port. This is an informational message.

Recommended Action    No action is required.

Error Message      ACLTCAM-6-PORTUP: Translation Port [chars] UP. 

Explanation    A port configured as TL Port is UP and operational. [chars] is the interface-id string that identifies the TL Port. This is an informational message.

Recommended Action    No action is required.

ACL Messages

ACL-2

Error Message      ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: 
[chars]. 

Explanation    Failed to do high availability operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message      ACL-2-ACL_INIT_FAILED: Initialization failed for ACL: [chars], 
reason: [hex]. 

Explanation    Initialization failed for ACL due to [chars], reason: [hex].

Recommended Action    No action is required.

Error Message      ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: 
[chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], 
restart count: [dec]. 

Explanation    Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].

Recommended Action    No action is required.

Error Message      ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars]. 

Explanation    Failed to do MTS operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message      ACL-2-ACL_MTS_Q_FULL: MTS queue for SAP [dec] is full 

Explanation    MTS queue for SAP [dec] is full

Recommended Action    No action is required.

Error Message      ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options setting to [hex] 
failed for opCode: [dec]. 

Explanation    MTS options setting to [hex] failed for opCode: [dec].

Recommended Action    No action is required.

Error Message      ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade Pending Messages Array 
is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: 
[hex] 

Explanation    ACL Upgrade Pending Messages Array is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]

Recommended Action    No action is required.

Error Message      ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation: [chars], reason: 
[hex]. 

Explanation    Failed to do PSS operation [chars]. [hex] is the reason.

Recommended Action    No action is required.

Error Message      ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has version 
[dec].[dec].[dec], expected version [dec].[dec].[dec]. 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version.

Recommended Action    No action is required.

Error Message      ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error: [hex] 

Explanation    ACL runtime failure is reported as [chars] [dec], reason: [hex].

Recommended Action    No action is required.

Error Message      ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars]. 

Explanation    Failed to do TCAM operation. [chars] is the reason.

Recommended Action    No action is required.

ACL-3

Error Message      ACL-3-ACL_MTS_Q_LEAK: Possible MTS buffer leak for SAP [dec] 

Explanation    Possible MTS buffer leak for SAP [dec]

Recommended Action    No action is required.

ACL-4

Error Message      ACL-4-ACL_MTS_Q_HIGH: MTS queue for SAP [dec] is close to full 

Explanation    MTS queue for SAP [dec] is close to full

Recommended Action    No action is required.

Error Message      ACL-4-ACL_WARNING: [chars] [dec] 

Explanation    ACL warning messages is reported as [chars] [dec].

Recommended Action    No action is required.

ACL-5

Error Message      ACL-5-ACL_ADJ_SHARING_STATUS: Successfully completed "[chars]" on 
Generation 2 linecards. 

Explanation    Successfully completed the command [chars] on Generation 2 linecards.

Recommended Action    No action is required.

ACL-6

Error Message      ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex]. 

Explanation    ACL system health management event status is reported as [chars] [hex].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_E_PORT_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL xEport event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL FCC event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex]. 

Explanation    ACL linecard event status is reported as [chars] [dec].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL multicast event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL Nx Port event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL portmode event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_RUNTIME_STATUS: [chars] [dec] 

Explanation    ACL runtime status is reported as [chars] [dec].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars] [chars]. 

Explanation    ACL SPAN destination config event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars]. 

Explanation    ACL SPAN source config event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_STATUS: ACL Status: [chars]. 

Explanation    ACL status is reported as [chars].

Recommended Action    No action is required.

Error Message      ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL update SSRAM for QoS event status is reported as [chars] [chars].

Recommended Action    No action is required.

AMM-SLOT#-0

Error Message      AMM-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed! 

Explanation    AMM failed to initialize CLI infrastructure's backend library. This is a fatal error.

Recommended Action    No action is required.

Error Message      AMM-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization 
failed! 

Explanation    AMM failed to initialize timer library. This is a fatal error.

Recommended Action    No action is required.

AMM-SLOT#-2

Error Message      AMM-SLOT#-2-AMM_MEM_ALLOC: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure

Recommended Action    No action is required.

Error Message      AMM-SLOT#-2-AMM_RECOVERY_ERROR: Error in Recovery: [chars] 

Explanation    AMM failed to recover after a re-start. This is a fatal error.

Recommended Action    No action is required.

AMM-SLOT#-6

Error Message      AMM-SLOT#-6-INITIALIZED: Internal state created [chars] 

Explanation    AMM has created its internal state stateless/stateful [chars].

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while 
Ascii configuration was being applied. Please use show startup-config log to view 
details 

Explanation    At least one command failed while Ascii configuration was being applied

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_LIB_INVOKE_ERR: Ascii config library invocation 
error: [chars] 

Explanation    Error encountered while library function was being invoked to display Ascii configuration

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_OPER_FAIL: Operation failed because of [chars] 

Explanation    Operation failed

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_ROLLBACK_FAILED: Rollback to checkpoint [chars] 
Failed, Going to undo the changes (atomic option) 

Explanation    Rollback operation failed for atomic option

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_ROLLBACK_UNDO_FAILED: Undo failed for atomic 
Rollback, Please correct the error manually and retry rollback 

Explanation    Undoing the rollback changes (for atomic behavior) Failed

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-ACFG_SYSLOG_INIT_FAILED: Ascii config Syslog Init Error 

Explanation    Error encountered while Initializing Syslog for Ascii Config

Recommended Action    No action is required.

Error Message      ASCII-CFG-2-PSS_VER_FAIL: PSS file [chars] has version 
[dec].[dec].[dec], expected version [dec].[dec].[dec] 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      ASCII-CFG-3-ACFG_MTSERROR: [chars] 

Explanation    Ascii-cfg-server (rollback process) encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE: cleared all the 
configuration checkpoints 

Explanation    Cleared all the configuration checkpoints

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: Created configuration 
checkpoint [chars] 

Explanation    Created configuration checkpoint

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: Deleted configuration 
checkpoint [chars] 

Explanation    Deleted configuration checkpoint

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_MAX_CHECKPOINTS: Maximum no of checpoints reached, 
Removing the oldest checkpoint 

Explanation    Maximum no.of checkpoints reached, removing the oldest checkpoint

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback 
to checkpoint [chars] (with atomic option) 

Explanation    Performing configuration rollback with atomic option

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback to 
checkpoint [chars] (with best-effort option) 

Explanation    Performing configuration rollback with best-effort option

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration 
rollback to checkpoint [chars] (with stop-at-first failure option) 

Explanation    Performing configuration rollback with stop-at-first-failure option

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-INFORMATION: [chars] 

Explanation    An event happend that affects Acfg-Rollback. [chars] indicates the event

Recommended Action    No action is required.

Error Message      ASCII-CFG-6-PSS_ERR: [chars] 

Explanation    An error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

ASSOC_MGR-0

Error Message      ASSOC_MGR-0-EMERGENCY_MSG: [chars] 

Explanation    Association Manager Emergency Message

Recommended Action    Please file the bug for Association Manager Component throCDETS'

ASSOC_MGR-1

Error Message      ASSOC_MGR-1-ALERT_MSG: [chars] 

Explanation    Association Manager Alert Message

Recommended Action    Association Manager Internal Operation Alert

ASSOC_MGR-2

Error Message      ASSOC_MGR-2-CRITICAL_MSG: [chars] 

Explanation    Association Manager Critical Message

Recommended Action    No action is required.

ASSOC_MGR-3

Error Message      ASSOC_MGR-3-ERROR_MSG: [chars] 

Explanation    Association Manager Error Message

Recommended Action    No action is required.

ASSOC_MGR-4

Error Message      ASSOC_MGR-4-WARN_MSG: [chars] 

Explanation    Association Manager Warning Message

Recommended Action    No action is required.

ASSOC_MGR-5

Error Message      ASSOC_MGR-5-NOTIF_MSG: [chars] 

Explanation    Association Manager Notification Message

Recommended Action    No action is required.

ASSOC_MGR-6

Error Message      ASSOC_MGR-6-ASSOC_ACTIVATED: Association Activated for vlan id:[dec] 
<--

Explanation    Association Activated

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_CREATED: Association Created for vlan id:[dec] <--

Explanation    Association Created

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_DEACTIVATED: Association Deactivated for vlan id: 
[dec] <--

Explanation    Association Deactivated

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_DELETED: Association Deleted for vlan id: [dec] <--

Explanation    Association Deleted

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_MGR_STATEFULL_RESTART: Association Manager 
Statefull Restart 

Explanation    Association Manager Stateful Restart

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_MGR_STATELESS_RESTART: Association Manager 
Stateless Restart 

Explanation    Association Manager Stateless Restart

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG: Association status for vlan id: 
[dec] <--

Explanation    Association Operational State Change

Recommended Action    No action is required.

Error Message      ASSOC_MGR-6-INFO_MSG: [chars] 

Explanation    ASSOC Manager Informational Message

Recommended Action    No action is required.

ASSOC_MGR-7

Error Message      ASSOC_MGR-7-DEBUG_MSG: [chars] 

Explanation    Association Manager Debug Message

Recommended Action    No action is required.

BFDC Messages

BFDC-SLOT#-2

Error Message      BFDC-SLOT#-2-BFDC_GENERAL_FAILURE: General failure. [chars] 

Explanation    General failure. This is a critical failure

Recommended Action    No DDTS.

Error Message      BFDC-SLOT#-2-BFDC_MALLOC_FAILED: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure

Recommended Action    No DDTS.

Error Message      BFDC-SLOT#-2-BFDC_MTS_FAILURE: MTS failure. [chars] 

Explanation    MTS related failure. This is a critical failure

Recommended Action    No DDTS.

BFD Messages

BFD-3

Error Message      BFD-3-REACHED_CAPACITY_LIMIT: BFD session [chars] creation on 
interface [chars] failed due to capacity limit [dec] 

Explanation    BFD session [chars] creation on interface [chars] failed due to current capacity limit [dec]

Recommended Action    Please remove current bfd sessions to make room for new ones

Error Message      BFD-3-SESSION_ACL_INSTALL_GAVE_UP: BFD session [chars] installation 
failed due to ACL installation failure interface [chars] 

Explanation    BFD session [chars] installation failed due to ACL installation failure interface [chars

Recommended Action    Maximum acl install retries exceeded. Please to free up acl resources

Error Message      BFD-3-SESSION_ACL_REMOVE_GAVE_UP: BFD session [chars] removal failed 
due to ACL removal failure interface [chars] 

Explanation    BFD session [chars] removal failed due to ACL removal failure interface [chars

Recommended Action    Maximum acl removal retries exceeded. Please manually remove bfd sessions

Error Message      BFD-3-SESSION_CREATE_FAIL: Failed to create BFD session to neighbor 
[chars] over intertface [chars]. Reason [chars] 

Explanation    Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars]

Recommended Action    SYSLOGDPC_NO_ACTION

BFD-4

Error Message      BFD-4-INVALID_NBR: Attempt to BFD session failed for application 
[chars]. 

Explanation    Attempt to BFD session failed for application [chars].

Recommended Action    No action is required.

Error Message      BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session for neighbor 
[chars] failed: Reason [chars] ([hex]). 

Explanation    Attempt to delete BFD session for neighbor [chars] failed: Reason [chars] (0x[hex]).

Recommended Action    No action is required.

BFD-5

Error Message      BFD-5-BFD_DISABLED: BFD Disabled 

Explanation    BFD Service Disabled

Recommended Action    No action is required.

Error Message      BFD-5-BFD_ENABLED: BFD Enabled 

Explanation    BFD Service enabled

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_ACTIVE_PARAMS_CHANGE: Local parameter of BFD session 
[hex] has changed [chars] 

Explanation    Local parameter of BFD session 0x[hex] has changed [chars]

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_CREATED: BFD session to neighbor [chars] on interface 
[chars] has been created 

Explanation    BFD session to neighbor [chars] on interface [chars]

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session 
[hex] has changed [chars] 

Explanation    Local parameter of BFD session 0x[hex] has changed [chars]

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_MOVED: BFD session [hex]: [chars] 

Explanation    BFD session 0x[hex]: [chars]

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_NO_RESOURCES: No resource for session to neighbor 
[chars] on interface [chars] 

Explanation    The BFD session can not be created or modified due to lack of resources. No resources for session to neighbor [chars]

Recommended Action    Remove other BFD sessions to free resources for this session

Error Message      BFD-5-SESSION_REMOVED: BFD session to neighbor [chars] on interface 
[chars] has been removed 

Explanation    BFD session to neighbor [chars] on interface [chars]

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on 
interface [chars] has gone down. Reason: [hex]. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: 0x[hex]. This may be as a result of the forwarding path being down.

Recommended Action    No action is required.

Error Message      BFD-5-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on 
interface [chars] is up. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] is up.

Recommended Action    No action is required.

BFD-6

Error Message      BFD-6-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to 
missing ACL resources for interface [chars] 

Explanation    BFD session [chars] failed due to missing ACL resources for interface [chars]

Recommended Action    No action is required.

Error Message      BFD-6-SESSION_ACL_REMOVE_FAILED: BFD session [chars] removal failed 
due to missing ACL resources for interface [chars] 

Explanation    BFD session [chars] removal failed due to missing ACL resources for interface [chars]

Recommended Action    No action is required.

BIOS_DAEMON Messages

BIOS_DAEMON-2

Error Message      BIOS_DAEMON-2-BIOS_DAEMON_FLASH_WARNING: Flash chip not supported by 
running image. Skipping bios upgrade. 

Explanation    BIOS CHIP NOT SUPPORTED

Recommended Action    No action is required.

Error Message      BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: System booted from 
Alternate BIOS Flash 

Explanation    Boot from Alternate

Recommended Action    SYSLOGDOC_NOACTION

Error Message      BIOS_DAEMON-2-BIOS_DAEMON_SUP_ERROR: BIOS Sector ([dec]) is write 
protected 

Explanation    BIOS WRITE PROTECTED

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

BIOS_DAEMON-5

Error Message      BIOS_DAEMON-5-BIOS_DAEMON_PRI_BOOT: System booted from Primary BIOS 
Flash 

Explanation    Boot from Primary

Recommended Action    SYSLOGDOC_NOACTION

BIOS_DAEMON-SLOT#-2

Error Message      BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is 
write protected 

Explanation    BIOS WRITE PROTECTED

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: System booted from 
Alternate BIOS Flash 

Explanation    Boot from Alternate

Recommended Action    SYSLOGDOC_NOACTION

BIOS_DAEMON-SLOT#-5

Error Message      BIOS_DAEMON-SLOT#-5-BIOS_DAEMON_LC_PRI_BOOT: System booted from 
Primary BIOS Flash 

Explanation    Boot from Primary

Recommended Action    SYSLOGDOC_NOACTION

BOOTUP_TEST Messages

BOOTUP_TEST-2

Error Message      BOOTUP_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    Online diagnostics EOBC test has failed

Recommended Action    No action is required.

Error Message      BOOTUP_TEST-2-EOBC_SKIP: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    Online diagnostics ManagementPort test has failed

Recommended Action    No action is required.

Error Message      BOOTUP_TEST-2-MGMT_PORT_FAIL: Module [dec] has failed test [chars] 
on Management Port due to error [chars] 

Explanation    Online diagnostics ManagementPort test has failed

Recommended Action    No action is required.

Error Message      BOOTUP_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] 
on Management Port due to error [chars] 

Explanation    Online diagnostics ManagementPort test is skipped

Recommended Action    No action is required.

BOOTVAR Messages

BOOTVAR-2

Error Message      BOOTVAR-2-ALLOC_MEMORY: Memory allocation failed 

Explanation    The service failed to allocate memory.

Recommended Action    Check if the system is low on memory, if so reset the switch.

Error Message      BOOTVAR-2-AUTOCOPY_FAILED: Autocopy of file [chars] to standby 
failed. [chars] (Error-id: [hex]) 

Explanation    The image deemed to be copied to standby via the auto-copy feature failed.

Recommended Action    Check error id for specified reason.

Error Message      BOOTVAR-2-AUTOSYNC_FAILED: Image autosync failed. Reason: [chars] 
([hex]) 

Explanation    Image synchronization failed.

Recommended Action    Check that there is enough space on the flash, as well as system high availability status.

Error Message      BOOTVAR-2-CONFIG_ERROR: Failed to update boot configuration 

Explanation    An error has occurred during the update of the boot configuration files

Recommended Action    Check that there is enough space on the flash, show boot to check the configured image names, show loader internal configuration to compare them with the current bootloader configuration, if they are not coherent do write erase and retry to save the configuration.

Error Message      BOOTVAR-2-IMAGE_NOT_COMPATIBLE: Warning: image [chars] is not 
compatible with the current platform in SUP [dec] 

Explanation    The input image name is not compatible with the current platform.

Recommended Action    Make sure a right image is specified before reboot.

BOOTVAR-3

Error Message      BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL: Autocopy of file [chars] to 
standby failed due to not enough disk space on standby 

Explanation    There is not enough disk space on the standby for the file to be copied.

Recommended Action    Clear space on the standby disk.

Error Message      BOOTVAR-3-INIT_FAILED: Initialization failed: Component [chars] 

Explanation    The service failed to start The failure occurs during initialization of the component [chars].

Recommended Action    Show processes to check the status of the other processes, pay attention to the specified component.

Error Message      BOOTVAR-3-LOAD_VERIFY_LIB_FAILED: Fetching library [chars] failed, 
reason=[chars] 

Explanation    Failed to load bootvar specified verification library.

Recommended Action    No action is required.

Error Message      BOOTVAR-3-MODULE_LOCK_FAIL: Unable to get module lock, please 
dontreload<error-id:[hex]

Explanation    Unable to acquire modlock to prevent user to reload during auto-sync.

Recommended Action    No action is required.

Error Message      BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY: auto-copy failed - not supported 
by neighbor supervisor. 

Explanation    Standby supervisor does not support auto-copy, thus failed.

Recommended Action    No action is required.

Error Message      BOOTVAR-3-VERIFY_FAILED: Image [chars] for bootvar [chars] 
verification failed, reason=[chars] 

Explanation    The image set for this bootvar has failed the verification process, this is just a warning.

Recommended Action    Check reason to determine actions.

BOOTVAR-5

Error Message      BOOTVAR-5-AUTOCOPY_SUCCEED: auto-copy of file [chars] to standby 
supervisor succeed 

Explanation    Auto copy of the file succeed, image integrity verified by standby.

Recommended Action    No action is required.

Error Message      BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED: Unable to ask standby to 
verify file [chars], error = [hex] 

Explanation    Upon copied the image to standby, failed to send message to ask standby to verify integrity.

Recommended Action    Turn auto-copy off and back on.

Error Message      BOOTVAR-5-AUTOSYNC_DONE: Image autosync done 

Explanation    The image synchronization done successfully.

Recommended Action    No action is required.

Error Message      BOOTVAR-5-AUTOSYNC_REBOOT: Rebooting standby after successful 
autosync 

Explanation    Image autosync has been successful, resetting the standby supervisor to load the new image.

Recommended Action    Check that the standby sup reloads correctly.

Error Message      BOOTVAR-5-AUTOSYNC_START: Starting image autosync. Please wait until 
completion... 

Explanation    The standby-sup has requested the sync of the current image.

Recommended Action    No action is required.

Error Message      BOOTVAR-5-IMAGE_NOTEXISTS: Warning: image [chars] 
doesntexistonsup[dec]'

Explanation    The input image name doesntexistonthespecifiedsupervisor.'

Recommended Action    Check whether the input image name you entered exists and make sure that you have the image on the flash before reboot.

Error Message      BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor 
supervisor, starting... 

Explanation    Info log reporting standbyssupportofauto-copy.Auto-copyisbeingstarted.'

Recommended Action    No action is required.

BOOTVAR-6

Error Message      BOOTVAR-6-ALREADY_IN_SYNC: Image already in sync 

Explanation    No need to update the image on the standby-sup.

Recommended Action    No action is required.

Error Message      BOOTVAR-6-AUTOCOPY_DID_NOT_START: Autocopy of file [chars] to 
standby did not start. [chars] (Error-id: [hex]) 

Explanation    Autocopy of the file did not start as the remote copy location does not exist

Recommended Action    No action is required.

Error Message      BOOTVAR-6-CONFIG_UPDATED: Boot configuration updated 

Explanation    The boot-loader configuration files have been successfully updated.

Recommended Action    No action is required.

Error Message      BOOTVAR-6-STARTING: Boot configuration initialized 

Explanation    The service has successfully started.

Recommended Action    No action is required.

CALLHOME Messages

CALLHOME-2

Error Message      CALLHOME-2-EVENT: [chars] 

Explanation    Callhome event [chars] occurred.

Recommended Action    If you have configured your email address to receive callhome notifications, please check your email for more details about this callhome event. If callhome was not enabled, please execute CLI commands relevant to the callhome event to get more information about the error

Error Message      CALLHOME-2-PROGRAM_EXIT: callhome process ending: [chars] 

Explanation    Callhome process is exiting with reason [chars].

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

CALLHOME-3

Error Message      CALLHOME-3-CALLHOME_CFS_MERGE_OPERATION_FAILED: [chars] 

Explanation    [chars1]

Recommended Action    Please check the reason for the failure of the cfs operation and rectify the problem

Error Message      CALLHOME-3-CALLHOME_CFS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2]

Recommended Action    Please check the reason for the failure of the cfs operation and rectify the problem

Error Message      CALLHOME-3-CALLHOME_MAX_ALERT_MSG: [chars] 

Explanation    [chars]

Recommended Action    Please check the reason for the generation of the callhome messages and rectify the problem

Error Message      CALLHOME-3-EVENT_PROCESS_ERROR: error in processing callhome event 
[chars] reason:[chars] 

Explanation    Error in processing callhome event [chars] reason:[chars]

Recommended Action    Please check your callhome configuration for proper configuration. Please check SMTP server address, email addresses for destination profiles and enable status of callhome. Use "show callhome" commands for displaying configuration.

Error Message      CALLHOME-3-MESSAGE_SIZE_EXCEED: message size for callhome 
alert:[chars] exceeds maximum limit for destination profile:[chars] 

Explanation    Message size for callhome alert:[chars] exceeds maximum limit for destination profile:[chars]

Recommended Action    Please check the maximum message size for the destination profile under question. Increase it if possible to match the maximum limit allowed by your email destinations.

CALLHOME-6

Error Message      CALLHOME-6-NONCRIT_EVENT: [chars] 

Explanation    Non-critical Callhome event [chars] occurred.

Recommended Action    If you have configured your email address to receive callhome notifications, please check your email for more details about this callhome event. If callhome was not enabled, please execute CLI commands relevant to the callhome event to get more information about the error

CDP Messages

CDP-2

Error Message      CDP-2-INITFAIL: CDP Daemon Initialization failed: [chars] 

Explanation    CDP Daemon Initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

CDP-3

Error Message      CDP-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    CDP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message      CDP-3-GENERROR: [chars] 

Explanation    CDP Daemon encountered a general error, one that does not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      CDP-3-MCASTBINDFAIL: Failed to bind for CDP multicast address on 
interface [hex] - [chars] 

Explanation    An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface [char] identifies the reason.

Recommended Action    No action is required.

Error Message      CDP-3-MTSERROR: [chars] 

Explanation    CDP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message      CDP-3-PKTRECVFAIL: Failed to receive packet - [chars] 

Explanation    Failed to receive packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      CDP-3-PKTSENDFAIL: Failed to send packet, interface [hex] - [chars] 

Explanation    Failed to send packet. [dec] identifies the interface [char] identifies the reason.

Recommended Action    No action is required.

Error Message      CDP-3-PSSERROR: [chars] 

Explanation    CDP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message      CDP-3-SOCKBINDFAIL: Failed to bind to raw socket, interface [hex] - 
[chars] 

Explanation    Failed to bind to raw socket. [dec] identifies the interface [char] identifies the reason.

Recommended Action    No action is required.

Error Message      CDP-3-SOCKOPENFAIL: Failed to open socket for receiving raw 802_2 
packets - [chars] 

Explanation    An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.

Recommended Action    No action is required.

CDP-4

Error Message      CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on [chars], with 
[chars] 

Explanation    Duplex mismatch discovered from the received cdp packet This is a warning message.

Recommended Action    No action is required.

Error Message      CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on 
[chars]([dec]), with [chars]([dec]) 

Explanation    Native VLAN mismatch discovered This is a warning message.

Recommended Action    No action is required.

CDP-5

Error Message      CDP-5-DISABLED: CDP is disabled 

Explanation    CDP is disabled on the device.

Recommended Action    No action is required.

Error Message      CDP-5-ENABLED: CDP is enabled 

Explanation    CDP is enabled on the device.

Recommended Action    No action is required.

Error Message      CDP-5-NEIGHBOR_ADDED: Device [chars] discovered of type [chars] with 
port [chars] on incoming port [chars] with ip addr [chars] and mgmt ip [chars] 

Explanation    Discovered a neighbor device. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-5-NEIGHBOR_REMOVED: CDP Neighbor [chars] on port [chars] has been 
removed 

Explanation    Deleted a neighbor device. This is an informational message.

Recommended Action    No action is required.

CDP-6

Error Message      CDP-6-CDPDUP: CDP Daemon Up. 

Explanation    CDP Daemon was created successfully and is up and running. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-6-CDPEXIT: CDP Daemon shutting down gracefully. 

Explanation    CDP Daemon is shutting down gracefully. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-6-PORTDISABLE: CDP disabled on port [chars] 

Explanation    CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-6-PORTDOWN: A CDP enabled port [chars] went down. 

Explanation    A CDP enabled port became un-operational. [chars] is the interface-ID string that identifies the port. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-6-PORTENABLE: CDP enabled on port [chars] 

Explanation    CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port. This is an informational message.

Recommended Action    No action is required.

Error Message      CDP-6-PORTUP: A CDP enabled port [chars] came up. 

Explanation    A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port. This is an informational message.

Recommended Action    No action is required.

CERT_ENROLL Messages

CERT_ENROLL-2

Error Message      CERT_ENROLL-2-CERT_EN_PROGRAM_EXIT: cert_enroll daemon exiting: 
[chars] 

Explanation    Cert_enroll daemon is exiting.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

CERT_ENROLL-3

Error Message      CERT_ENROLL-3-CERT_EN_ERROR_MESSAGE: [chars] 

Explanation    CERT_ENROLL Error Message

Recommended Action    No action is required.

Error Message      CERT_ENROLL-3-CERT_EN_FIPS_MODE_INIT_ERROR: Could not initialize 
FIPS mode : [chars] 

Explanation    FIPS mode initialization error

Recommended Action    No action is required.

CERT_ENROLL-6

Error Message      CERT_ENROLL-6-CERT_EN_MESSAGE: [chars] 

Explanation    CERT_ENROLL Message

Recommended Action    No action is required.

CFS Messages

CFS-2

Error Message      CFS-2-CFS_REJECT: CFS reject: [chars]: Switch WWN [chars], ip 
[chars], reason [chars] 

Explanation    CFS reject: [chars] Switch WWN [chars], ip [chars], reason [chars]

Recommended Action    No action is required.

Error Message      CFS-2-EXITING: Exit reason: [chars] 

Explanation    The CFS service process has exited due to [char]. The process has probably been restarted automatically.

Recommended Action    No action is required.

Error Message      CFS-2-FETCH_WWN_FAIL: Failed to get a valid switch mac from : [chars] 

Explanation    VDC/PFM manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received

Recommended Action    No action is required.

Error Message      CFS-2-GENERAL_ERROR: [chars] 

Explanation    The CFS service has encountered an critical error. The description of error is [str.]

Recommended Action    No action is required.

Error Message      CFS-2-INITFAIL: CFS Service Init failed: [chars] 

Explanation    CFS Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      CFS-2-LOCK_FAILED: lock failed for sap [dec] due to internal error. 

Explanation    Lock failed due to Unrestricted uncoordinated count is out of sync for sap [dec]

Recommended Action    To recover from this state run command cfsinternaldecrement-unrestricted<app-sap

Error Message      CFS-2-MALLOC_ERROR: Size [dec] bytes 

Explanation    The CFS service could not allocate memory.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      CFS-2-MTS_REJECT: Verification failed reject MTS message SAP 
[dec]:RR-token [hex] 

Explanation    This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then hence ignore the MTS message, Source SAP [dec]; RR-token [hex]

Recommended Action    No action is required.

Error Message      CFS-2-PSS_ERROR: [chars]: PSS ret. val=[dec] 

Explanation    The CFS service encountered error while operating on a persistent storage database.

Recommended Action    No action is required.

Error Message      CFS-2-WWN_MISMATCH: CFS detected a change in wwn old wwn: [chars] 
new wwn: [chars]. Reload the switch OR Flap the MCT if needed to recover from wwn 
change 

Explanation    CFS detected a change in wwn. Reload the switch OR Flap the MCT if neeeded to recover from wwn change

Recommended Action    No action is required.

CFS-3

Error Message      CFS-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    CFS Service is out of dynamic memory. [chars] specifies the context where the failure occured

Recommended Action    No action is required.

Error Message      CFS-3-APP_MERGE_FAILED: Merge failed for app [chars], local switch 
wwn [chars], remote switch wwn [chars].Please check 
showcfsmergestatusname[chars]'formoreinformation'

Explanation    The CFS service has detected a merge failure.

Recommended Action    No action is required.

Error Message      CFS-3-CFS_PSS_CORRUPTED: [chars] PSS found corrupted 

Explanation    The CFS service has detected corruption in one of its persistent information database. The database would be recreated.

Recommended Action    No action is required.

Error Message      CFS-3-DBERROR: [chars] 

Explanation    CFS Service encountered a database error. [chars] specifies the context where the failure occured.

Recommended Action    No action is required.

Error Message      CFS-3-FAILURE_RESPONSE: [chars] [hex] 

Explanation    CFS Service failed to get response [chars][hex] specify the context where the failure occured.

Recommended Action    No action is required.

Error Message      CFS-3-FIPS_TEST_FAILED: FIPS compliance test failed 

Explanation    FIPS compliance test failed

Recommended Action    No action is required.

Error Message      CFS-3-GENERROR: [chars] 

Explanation    CFS Service encountered a general error, one that does not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      CFS-3-LICERR: [chars] 

Explanation    CFS Service failed to get license.

Recommended Action    No action is required.

Error Message      CFS-3-MERGE_FAILED: Merge failed for app [chars], local switch wwn 
[chars],ip [chars], remote switch wwn [chars], ip [chars] 

Explanation    The CFS service has detected a merge failure.

Recommended Action    No action is required.

Error Message      CFS-3-MTSERROR: [chars] 

Explanation    CFS Service encountered an MTS error. [chars] specifies the context where the error occured.

Recommended Action    No action is required.

Error Message      CFS-3-PSSERROR: [chars] 

Explanation    CFS Service encountered a PSS error. [chars] specifies the context where the failure occured.

Recommended Action    No action is required.

Error Message      CFS-3-TIMEOUT_ERROR: [chars] [hex] 

Explanation    CFS Service encountered a timeout [chars][hex] specify the context where the failure occured.

Recommended Action    No action is required.

Error Message      CFS-3-UNKNOWN_MSG: Recvd. from Node=[dec] SAP=[dec] 

Explanation    The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.

Recommended Action    No action is required.

CFS-4

Error Message      CFS-4-LICEXP: [chars] 

Explanation    CFS Service license is going to expire. [chars] gives the expected time of expiry

Recommended Action    No action is required.

Error Message      CFS-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec] 

Explanation    There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    No action is required.

CFS-6

Error Message      CFS-6-BECAME_ACTIVE: Became ACTIVE from standby mode 

Explanation    The CFS service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    No action is required.

Error Message      CFS-6-BECAME_STDBY: Became STANDBY from active mode 

Explanation    The CFS service became standby from active mode.

Recommended Action    No action is required.

Error Message      CFS-6-EXCESSIVE_DELAY: [chars] 

Explanation    Excessive time taken for a processing event. The description of the event is [str.]

Recommended Action    No action is required.

Error Message      CFS-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system 
manager: Reason=[chars] 

Explanation    The CFS service was unable to send heartbeat to the system manger

Recommended Action    No action is required.

Error Message      CFS-6-GENERAL_EVENT: [chars] 

Explanation    The CFS service has generated an important event. The description of the event is [str.]

Recommended Action    No action is required.

Error Message      CFS-6-INVALID_CHECKSUM: Received packet from peer on if-index([hex]) 
with corrupted checksum 

Explanation    This could be because of errors in the link

Recommended Action    No action is required.

Error Message      CFS-6-INVALID_IF_INDEX: Received packet on if-index([hex]) which is 
not recognized by CFS 

Explanation    The if-index does not match with the if-index used in discovery or we might have already recieved an adjacency cleanup message for this if-index. Check if the if-index is that of the port-channel or a physical if-index

Recommended Action    No action is required.

Error Message      CFS-6-LOGICAL_DISTRIBUTION_INFO: vsan [dec], source wwn [chars], ip 
[chars] app-id [dec], session-id [dec], user [chars], [chars] 

Explanation    Vsan [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars]

Recommended Action    No action is required.

Error Message      CFS-6-PHY_DISTRIBUTION_INFO: source wwn [chars], ip [chars], app-id 
[dec], session-id [dec], user [chars], [chars] 

Explanation    Source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars]

Recommended Action    No action is required.

Error Message      CFS-6-PSS_CREATED: [chars] PSS Created 

Explanation    One of the persistent information database of CFS service has been recreated

Recommended Action    No action is required.

Error Message      CFS-6-PSS_DESTROYED: [chars] PSS Destroyed 

Explanation    One of the persistent information databases of CFS Service has been intentionally destroyed and would be recreated.

Recommended Action    No action is required.

Error Message      CFS-6-REGION_CTX_REMOVED: Region info is deleted for [chars] 

Explanation    [chars] is in logical scope. Regions are supported only physical scope applications

Recommended Action    No action is required.

Error Message      CFS-6-SERVICE_UP: Initialized [chars] 

Explanation    The CFS service is up and ready to accept client requests The service was initialized in [char] mode.

Recommended Action    No action is required.

Error Message      CFS-6-SRVCREATED: CFS Service created 

Explanation    CFS Service was created successfully and is up and running. This is an informational message.

Recommended Action    No action is required.

Error Message      CFS-6-SRVEXIT: CFS Service shutting down gracefully 

Explanation    CFS Service is shutting down gracefully. This is an informational message.

Recommended Action    No action is required.

Error Message      CFS-6-SWITCHOVER: Switching Over to other Sup. 

Explanation    The CFS service has successfully switched over to the standby supervisor card.

Recommended Action    No action is required.

CIMSRVPROV Messages

CIMSRVPROV-2

Error Message      CIMSRVPROV-2-CIM_SYSLOG_EXIT: Message:[chars] errcode:[dec] 

Explanation    Exit due to critical error

Recommended Action    No action is required.

Error Message      CIMSRVPROV-2-CIM_SYSLOG_PSS_SNAPSHOT_ERR: Source URI:[chars] 
Destination URI:[chars] errcode:[dec] 

Explanation    PSS snapshot error

Recommended Action    No action is required.

Error Message      CIMSRVPROV-2-CIM_SYSLOG_SDWRAP_ERR: Description:[chars] 
errcode:[dec] 

Explanation    Debug infrastructure error

Recommended Action    No action is required.

CIMSRVPROV-3

Error Message      CIMSRVPROV-3-CIM_SYSLOG_COPY_CONFIG_ERR: Message:[chars] 
URI:[chars] errcode:[dec] 

Explanation    Copy running startup error

Recommended Action    No action is required.

Error Message      CIMSRVPROV-3-CIM_SYSLOG_FILE_ERR: Purpose:[chars] Filename:[chars] 
errcode:[dec] 

Explanation    File handling error

Recommended Action    No action is required.

Error Message      CIMSRVPROV-3-CIM_SYSLOG_MTS_ERR: message [chars] 

Explanation    MTS message handling error

Recommended Action    No action is required.

Error Message      CIMSRVPROV-3-CIM_SYSLOG_PSS_ERR: Purpose:[chars] URI:[chars] 
errcode:[dec] 

Explanation    PSS handling error

Recommended Action    No action is required.

CIMSRVPROV-6

Error Message      CIMSRVPROV-6-LOG_CIM_CERTIFICATE_CLEARED: Cleared certificate 
[chars] 

Explanation    Cleared a certificate named [chars].

Recommended Action    No action is required.

Error Message      CIMSRVPROV-6-LOG_CIM_CERTIFICATE_INSTALLED: Installed certificate 
[chars] 

Explanation    Installed a certificate named [chars].

Recommended Action    No action is required.

CLIS Messages

CLIS-5

Error Message      CLIS-5-CLIS_SYSLOG_CMD_REMOVED: Command deleted from the NVDB: 
[chars] 

Explanation    Command removal due to configuration change

Recommended Action    No action is required.

CLOUD Messages

CLOUD-2

Error Message      CLOUD-2-PROGRAM_EXIT: cloud-discovery process ending: [chars] 

Explanation    Cloud-discovery process is exiting with reason [chars].

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

CLOUD-3

Error Message      CLOUD-3-CLOUD_CFS_MERGE_OPERATION_FAILED: [chars] 

Explanation    [chars1]

Recommended Action    Please check the reason for the failure of the cfs operation and rectify the problem

Error Message      CLOUD-3-CLOUD_CFS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2]

Recommended Action    Please check the reason for the failure of the cfs operation and rectify the problem

Error Message      CLOUD-3-CLOUD_FEATURE_MANAGER_ERROR: [chars] : [chars] 

Explanation    [chars1] [chars2]

Recommended Action    Please check the reason for error using feature manager and rectify the problem

Error Message      CLOUD-3-CLOUD_PSS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2]

Recommended Action    Please check the reason for the failure of the pss operation and rectify the problem

CLOUD-6

Error Message      CLOUD-6-CLOUD_DISCOVERY_DONE: discovery over 

Explanation    Cloud-discovery started

Recommended Action    Check cloud membership

Error Message      CLOUD-6-CLOUD_DISCOVERY_STARTED: [chars] discovery started 

Explanation    Cloud-discovery started

Recommended Action    Check cloud-discovery status after sometime

CLUSTER Messages

CLUSTER-2

Error Message      CLUSTER-2-CLUSTER_CAP_ADD_FAIL: Failed to add cluster capability 
[dec] 

Explanation    Cluster capability addition failed

Recommended Action    No action is required.

Error Message      CLUSTER-2-CLUSTER_CAP_DEL_FAIL: Failed to delete cluster capability 
[dec] 

Explanation    Cluster capability deletion failed

Recommended Action    No action is required.

CMOND Messages

CMOND-2

Error Message      CMOND-2-CMOND_ALERT_MSG: [chars] 

Explanation    Alert message

Recommended Action    No action is required.

Error Message      CMOND-2-CMOND_ERROR_MSG: [chars] 

Explanation    Error message

Recommended Action    No action is required.

CMPPROXY Messages

CMPPROXY-2

Error Message      CMPPROXY-2-LOG_CMP_IS_NOT_UP: Connectivity Management processor (on 
module [dec]) did not come up 

Explanation    Connectivity Management processor is not sending heartbeats on this module

Recommended Action    No action is required.

Error Message      CMPPROXY-2-LOG_CMP_UP: Connectivity Management processor(on module 
[dec]) is now UP 

Explanation    Connectivity Management processor has come up and is exchanging heartbeats with CP on this SUP slot

Recommended Action    No action is required.

Error Message      CMPPROXY-2-LOG_CMP_WENT_DOWN: Connectivity Management processor (on 
module [dec]) went DOWN 

Explanation    Connectivity Management processor has either gone down or is not sending heartbeats for a long time

Recommended Action    No action is required.

CMPPROXY-5

Error Message      CMPPROXY-5-LOG_CMP_AAA_FAILURE: Authentication failed for a login 
from CMP (on module [dec]) 

Explanation    A login attempt has been denied access from Connectivity management processor (CMP) as authentication did not succeed

Recommended Action    No action is required.

Error Message      CMPPROXY-5-MALLOC_FAILURE: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed.

Recommended Action    No action is required.

CMPPROXY-6

Error Message      CMPPROXY-6-LOG_CMP_AAA_SUCCESS: Authentication succeeded for a login 
from CMP (on module [dec]) 

Explanation    A login attempt has succeeded from Connectivity management processor (CMP) in getting access as AAA succeeded

Recommended Action    No action is required.

COPP Messages

COPP-1

Error Message      COPP-1-COPP_DROPS1: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

COPP-2

Error Message      COPP-2-COPP_DROPS2: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message      COPP-2-COPP_INIT_FAIL: CoPP Initialization failed: [chars] 

Explanation    CoPP Initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      COPP-2-COPP_MTS_FAIL: Failed to do MTS operation: [chars] 

Explanation    Failed to do MTS operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      COPP-2-COPP_NO_POLICY: Control-plane is unprotected. 

Explanation    There isntanypolicyconfiguredtoprotectcontrol-plane.'

Recommended Action    No action is required.

Error Message      COPP-2-COPP_PROFILE_DIFF: CoPP Default Profile may have changed, 
please check the diffs using show copp diff profile <profile-type

Explanation    CoPP Default Profile may have changed, please check the diffs using show copp diff profile <profile-type

Recommended Action    No action is required.

COPP-3

Error Message      COPP-3-COPP_ALLOC_FAIL: Memory allocation failure: [chars] 

Explanation    Failed to alloc required memory. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      COPP-3-COPP_DROPS3: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message      COPP-3-COPP_PPF_FAIL: Error during PPF operation: [chars] 

Explanation    Failed to do PPF operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      COPP-3-COPP_PSS_FAIL: Error during PSS operation: [chars] 

Explanation    Failed to do PSS operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

COPP-4

Error Message      COPP-4-COPP_DROPS4: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

COPP-5

Error Message      COPP-5-COPP_DISABLED: COPP Disabled 

Explanation    COPP Service Disabled

Recommended Action    No action is required.

Error Message      COPP-5-COPP_DROPS5: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message      COPP-5-COPP_ENABLED: COPP Enabled 

Explanation    COPP Service nabled

Recommended Action    No action is required.

Error Message      COPP-5-COPP_INIT: COPP initialized 

Explanation    COPP Service Initialized

Recommended Action    No action is required.

COPP-6

Error Message      COPP-6-COPP_DROPS6: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message      COPP-6-COPP_POLICY_ATTACHED: CoPP policy has been attached to control 
plane interface. 

Explanation    CoPP policy has been attached to control plane interface.

Recommended Action    No action is required.

Error Message      COPP-6-COPP_POLICY_DETACHED: CoPP policy has been detached from 
control plane interface. 

Explanation    CoPP policy has been detached from control plane interface.

Recommended Action    No action is required.

COPP-7

Error Message      COPP-7-COPP_DROPS7: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message      CORE-DMON-2-MODULE_COREDUMP_DONE: kernel coredump completed on 
module:[dec] 

Explanation    Kernel coredump finishing on a module

Recommended Action    No action is required.

Error Message      CORE-DMON-2-MODULE_COREDUMP_STARTED: kernel coredump started on 
module:[dec] 

Explanation    Kernel coredump starting on a module

Recommended Action    No action is required.

Error Message      CORE-DMON-3-NO_SPACE: Failed to save core file [chars]. Try removing 
existing core files. 

Explanation    Not enough space to save new core files

Recommended Action    No action is required.

CPPA_MGR Messages

CPPA_MGR-3

Error Message      CPPA_MGR-3-ENABLE_VB_FAILURE: Virtual service blade [dec] could not 
be [chars]. Error: [chars] 

Explanation    The requested virtual blade operation could not be completed

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-NO_HB_REBOOT: No heartbeat from agent service. Nexus1010 
is rebooted 

Explanation    No heartbeat from agent service. Nexus1010 is rebooted

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-REMOTE_ILO_REBOOT: Remote mgmt feature rebooted other 
Nexus1010 using ILO 

Explanation    Remote mgmt feature rebooted other Nexus1010 using ILO

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-RESTORE_FAILURE: Agent version could not be restored to 
make versions match 

Explanation    The previous agent version could not be restored. System needs to be reinstalled to recover

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-SOME_PNIC_FAILURE: Not all the Nexus1010 physical NICs 
are detected. Check for failure 

Explanation    Not all the physical NICs are detected. Check for failure

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-UNDO_WRITE_ERASE: Undo Write Erase: [chars] 

Explanation    The software undo write erase result:

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-UPGRADE_FAILED: Upgrade failed: [chars] 

Explanation    The software upgrade could not complete because of errors

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-VERSION_MISMATCH: Agent version mismatch detected. System 
will be reloaded 

Explanation    The cppa_mgr and the underlying agent are not running the same software version

Recommended Action    No action is required.

Error Message      CPPA_MGR-3-WRITE_ERASE: Write Erase: [chars] 

Explanation    The software write erase result:

Recommended Action    No action is required.

CPPA_MGR-5

Error Message      CPPA_MGR-5-REMOTE_VB_HA_FAILURE: Operation failed in standby for 
virtual service blade [dec]: [chars] 

Explanation    An error occurred while processing a command from active at standby

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-REMOTE_VB_IMG_FAILURE: Could not verify image in standby 
for virtual service blade [dec] creation: [chars] 

Explanation    An error occurred while processing image required for vb creation at standby

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-UPGRADE_COMPLETE: Upgrade completed successfully 

Explanation    The software upgrade completed with no errors

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-UPGRADE_START: Upgrade started. Image: [chars] 

Explanation    A software upgrade has been initiated by the user

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-VB_DEPLOYED: Virtual service blade [chars] deployed 

Explanation    Virtual service blade deployed on nexus1010 successfully

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-VB_REMOVED: Virtual service blade [chars] removed 

Explanation    Virtual service blade removed by user

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-VB_RESTARTED: Virtual service blade [chars] restarted 

Explanation    Virtual service blade restarted by user

Recommended Action    No action is required.

Error Message      CPPA_MGR-5-VB_SHUT: Virtual service blade [chars] moved into shut 
state 

Explanation    Virtual service blade shut by user

Recommended Action    No action is required.

CREDITMON Messages

CREDITMON-SLOT#-2

Error Message      CREDITMON-SLOT#-2-SYSERR_CREDITMON_APP_EXITED: [chars] 

Explanation    Credit Monitor application exited

Recommended Action    No action is required.

Error Message      CREDITMON-SLOT#-2-SYSERR_CREDITMON_MTS_INIT_ERR: [chars] 

Explanation    Credit Monitor error binding to MTS

Recommended Action    No action is required.

CTS Messages

CTS-2

Error Message      CTS-2-CTS_AUTHENT_FAILURE: CTS Authentication failure on Port 
[chars] (CTS Failure Reason: [chars] [chars]) 

Explanation    Fibre-Channel Authentication failure on Port [chars].(Reason Code [chars] Detail [chars]). Please check password configurations and ensure appropriate security modes on this port as well as peer port

Recommended Action    No action is required.

Error Message      CTS-2-CTS_FIPS_BYPASS_TEST_FAILED: FIPS bypass test failed for 
interface: [chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-CTS_SAP_FAILED: SAP exchange failed on interface [chars]. 
(Reason: [chars]) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-CTS_SAP_REKEY_FAILED: SAP exchange failed on interface 
[chars]. (Reason: [chars]) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-DBG_INIT_FAILED: Debug Infrastructure Initialization failed ( 
[chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-FC2_E_INIT_FAILED: Fibre-Channel Initialization of an E_Port 
failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the FC-2 E-Port infrastructure.

Recommended Action    No action is required.

Error Message      CTS-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an F_Port 
failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the FC-2 F-Port infrastructure.

Recommended Action    No action is required.

Error Message      CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT: Received an unexpected/unknown FC-2 
frame on [chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-FSMU_INIT_FAILED: State Machine Infrastructure Initialization 
failed ( [chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-IPC_INIT_FAILED: IPC (Inter Process Communication) 
Initialization failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the IPC infrastructure.

Recommended Action    No action is required.

Error Message      CTS-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service 
exiting 

Explanation    License of [chars] is unavailable. Service will exit now

Recommended Action    Please install the license file to continue using the feature.

Error Message      CTS-2-MEM_FAILED: Memory operations failed File: [chars] Line [dec] 
for size [hex] bytes 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-POST_INIT_FAILED: Post-Initialization failed ( [chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed ( 
[chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-RBACL_ENFORCEMENT_FAILED: Failed to [chars] RBACL enforcement 
on [chars] %lu 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-RBACL_LC_INSERT_FAILED: RBACL programming failed for inserted 
module [dec] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-RBACL_TCAM_SPACE_NOT_ENOUGH: Not enough free space left on TCAM 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-RBACL_UNABLE_PARSE_ACE: Unable to parse RBACL ACE substring: 
[chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-RBACL_UPDATE_FAILED: Failed to [chars] RBACL [chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-SGT_DGT_RBACL_DELETE_FAILED: Failed to delete RBACL for 
sgt:[dec] dgt:[dec] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-2-SGT_DGT_RBACL_UPDATE_FAILED: Failed to apply RBACL:[chars] to 
sgt:[dec] dgt:[dec] 

Explanation    .

Recommended Action    No action is required.

CTS-3

Error Message      CTS-3-DOT1X_AUTHC_FAILED: DOT1X authentication failed on port: 
[chars] 

Explanation    DOT1X authentication failed on the port

Recommended Action    No action is required.

CTS-5

Error Message      CTS-5-CTS_IP_SGT_MAP_DELETE: IP-SGT mapping deleted for [chars] on 
[chars] %lu 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-5-CTS_IP_SGT_MAP_UPDATE: [chars] assigned SGT [chars] 

Explanation    .

Recommended Action    No action is required.

CTS-6

Error Message      CTS-6-CTS_FIPS_BYPASS_TEST_PASSED: FIPS bypass test passed for 
interface: [chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      CTS-6-SXP_STATE_CHANGE: CTS SXP [chars] 

Explanation    .

Recommended Action    No action is required.

DCEFIB Messages

DCEFIB-SLOT#-0

Error Message      DCEFIB-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed! 

Explanation    L2mp unicast fib failed to initialize CLI infrastructure's backend library. This is a fatal error.

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization 
failed! 

Explanation    L2mp unicast fib failed to initialize timer library. This is a fatal error.

Recommended Action    No action is required.

DCEFIB-SLOT#-2

Error Message      DCEFIB-SLOT#-2-DCEFIB_MEM_ALLOC: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-2-DCEFIB_RECOVERY_ERROR: Error in Recovery: [chars] 

Explanation    L2mp unicast fib failed to recover after a re-start. This is a fatal error.

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-2-U2FIB_ERR: [chars] 

Explanation    L2mp unicast fib encountered an error:

Recommended Action    No action is required.

DCEFIB-SLOT#-6

Error Message      DCEFIB-SLOT#-6-INITIALIZED: Internal state created [chars] 

Explanation    L2mp unicast fib has created its internal state stateless/stateful [chars].

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-6-U2FIB_INFO: [chars] 

Explanation    L2mp unicast fib notice:

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-6-VDC_CREATED: VDC [dec] created 

Explanation    Request to create VDC [dec] in l2mp unicsat fib was successful.

Recommended Action    No action is required.

Error Message      DCEFIB-SLOT#-6-VDC_REMOVED: VDC [dec] Removed 

Explanation    L2mp unicast fib has successfully removed VDC [dec] from its databases.

Recommended Action    No action is required.

DEBUGPROXY Messages

DEBUGPROXY-6

Error Message      DEBUGPROXY-6-SSM_DEBUG_PROXY_COMMON: SSM debug proxy [chars] [dec] 

Explanation    General SSM debug proxy information

Recommended Action    No action is required.

Error Message      DEVICE-ALIAS-2-ALLOC_FAILED: Memory allocation failed for size:[dec] 
type:[dec] 

Explanation    Memory allocation failed for size [dec] type [dec]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-2-INIT_FAILED: [chars] 

Explanation    An error occurred during initialization. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-CFS_OPER_FAILED: [chars] 

Explanation    An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-CLEAR_FAILED: [chars] 

Explanation    An error occurred while clearing the session. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-COMMIT_FAILED: [chars] 

Explanation    An error occurred while committing the database. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-COMMIT_REJECTED: [chars] 

Explanation    Commit request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-LOCK_FAILED: [chars] 

Explanation    An error occurred while acquiring the lock. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-LOCK_REJECTED: [chars] 

Explanation    Lock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_ACTIVATION_FAILED: [chars] 

Explanation    An error occurred while activating the merged database. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_ACTIVATION_REJECTED: [chars] 

Explanation    Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_FAILED: [chars] 

Explanation    An error occurred during merge operation. [chars] indicates the reason for failure.

Recommended Action    Compare device-alias configuration with the other switches in the fabric, resolve the conflicts if any and commit the changes.

Error Message      DEVICE-ALIAS-3-MERGE_MREQ_REJECTED: [chars] 

Explanation    MREQ received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_MRESP_REJECTED: [chars] 

Explanation    MRESP received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_VALIDATION_FAILED: [chars] 

Explanation    An error occurred while validating the merged database. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MERGE_VALIDATION_REJECTED: [chars] 

Explanation    Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-MTS_OPER_FAILED: [chars] 

Explanation    An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-PSS_OPER_FAILED: [chars] 

Explanation    An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-UNLOCK_FAILED: [chars] 

Explanation    An error occurred while releasing the lock. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-UNLOCK_REJECTED: [chars] 

Explanation    Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-VALIDATION_FAILED: [chars] 

Explanation    An error occurred while validating the database. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-3-VALIDATION_REJECTED: [chars] 

Explanation    Validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-CLEAR_FAILED_INFO: [chars] 

Explanation    An error occurred while clearing the session. [chars] indicates the additional information regarding failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-COMMIT_FAILED_INFO: [chars] 

Explanation    An error occurred while committing the database. [chars] indicates the additional information regarding failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-IMPORT_DEFINITION_CONFLICT: Fcalias [chars] could not 
be imported due to definition conflict 

Explanation    Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.

Recommended Action    Resolve the conflict and issue the import command again.

Error Message      DEVICE-ALIAS-6-IMPORT_MEMBER_TYPE_CONFLICT: Fcalias [chars] could 
not be imported due to having unsupported member type 

Explanation    Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members..

Recommended Action    Make sure that the fcalias has Port WWN based members and issue the import command again.

Error Message      DEVICE-ALIAS-6-IMPORT_NAME_CONFLICT: Fcalias [chars] could not be 
imported due to name conflict 

Explanation    Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.

Recommended Action    Resolve the conflict and issue the import command again.

Error Message      DEVICE-ALIAS-6-IMPORT_NUM_MEMBERS_CONFLICT: Fcalias [chars] could 
not be imported due to having unsupported number of members 

Explanation    Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member..

Recommended Action    Make sure that the fcalias has exactly one member and issue the import command again.

Error Message      DEVICE-ALIAS-6-LOCK_FAILED_INFO: [chars] 

Explanation    An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-MERGE_ACTIVATION_FAILED_INFO: [chars] 

Explanation    An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-MERGE_VALIDATION_FAILED_BUSY: [chars] 

Explanation    Merged database could not be validated as some of the applications returned busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    No DDTS.

Error Message      DEVICE-ALIAS-6-MERGE_VALIDATION_REJECTED_BUSY: [chars] 

Explanation    Merged database received from the remote switch could not be validated as some of the applications returned busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    No DDTS.

Error Message      DEVICE-ALIAS-6-UNLOCK_FAILED_INFO: [chars] 

Explanation    An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DEVICE-ALIAS-6-VALIDATION_ABORTED: [chars] 

Explanation    Local validation is aborted. [chars] indicates the reason why validation is aborted.

Recommended Action    No DDTS.

DEVICE_TEST Messages

DEVICE_TEST-2

Error Message      DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test 
[chars] [dec] times on device [chars] [chars] [dec] [chars] due to error [chars] 

Explanation    Online diagnostics ASICRegisterCheck test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-COMPACT_FLASH_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Compact Flash due to error [chars] 

Explanation    Online diagnostics CompactFlash test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-CRYPTO_DEVICE_FAIL: Module [dec] has failed test 
[chars] [dec] times on Crypto device due to error [chars] 

Explanation    Online diagnostics CryptoDevice test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    Online diagnostics EOBC test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-FAN_MOD_FAIL: Module [dec] has failed test [chars] 
[dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error 
[chars] error number [hex] 

Explanation    Online diagnostics SystemMgmtBus test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-MALLOC_FAILURE: Memory allocation failed 

Explanation    Device Test process could not allocate memory

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] 
on Management Port due to error [chars] 

Explanation    Online diagnostics ManagementPort test is skipped

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-NVRAM_FAIL: Module [dec] has failed test [chars] [dec] 
times on device NVRAM due to error [chars] 

Explanation    Online diagnostics NVRAM test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-OBFL_FAIL: Module [dec] has failed test [chars] [dec] 
times on device OBFL due to error [chars] 

Explanation    Online diagnostics OBFL test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-POWER_SUPPLY_FAIL: Module [dec] has failed test 
[chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to 
error [chars] error number [hex] 

Explanation    Online diagnostics SystemMgmtBus test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Primary BootROM due to error [chars] 

Explanation    Online diagnostics PrimaryBootROM test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Power Mgmt Bus on slot [dec] due to error [chars] 
error number [hex] 

Explanation    Online diagnostics PwrMgmtBus test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-RTC_FAIL: Module [dec] has failed test [chars] [dec] 
times on device RealTimeClock due to error [chars] 

Explanation    Online diagnostics RealTimeClock test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Secondary BootROM due to error [chars] 

Explanation    Online diagnostics SecondaryBootROM test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Spine Control Bus on slot [dec] due to error [chars] 
error number [hex] 

Explanation    Online diagnostics SpineControlBus test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-STANDBY_LOOPBACK_TEST_FAIL: Module [dec] has failed 
test [chars] [dec] times on [chars] [dec] due to error [chars] 

Explanation    Online diagnostics StandbyFabricLoopback test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-TWOWIRE_STW_FAIL: Module [dec] has failed test [chars] 
[dec] times on Status Bus on slot [dec] due to error [chars] 

Explanation    Online diagnostics Status bus test has failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-2-USB_FAIL: Module [dec] has failed test [chars] [dec] 
times on device USB due to error [chars] 

Explanation    Online diagnostics USB test has failed

Recommended Action    No action is required.

DEVICE_TEST-3

Error Message      DEVICE_TEST-3-STANDBY_TEST_GET_DIAG_VQI_FAIL: Standby test get diag 
vqi failed due to error [hex] 

Explanation    Device Test StandbyLoopback Test failed get vqi

Recommended Action    No action is required.

Error Message      DEVICE_TEST-3-STANDBY_TEST_GET_SPINE_FAIL: Standby test get spines 
failed due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test get spine failed

Recommended Action    No action is required.

Error Message      DEVICE_TEST-3-STANDBY_TEST_INIT_FAIL: Init for standby test failed 
due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test failed init process

Recommended Action    No action is required.

Error Message      DEVICE_TEST-3-STANDBY_TEST_MTS_FAIL: Mts Init for standby test 
failed due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test failed mts init

Recommended Action    No action is required.

Error Message      DEVICE_TEST-3-STANDBY_TEST_SOCKET_FAIL: Standby test socket error 
[chars]: [hex] 

Explanation    Device Test StandbyFabricLoopback Test Socket error

Recommended Action    No action is required.

DEVICE_TEST-4

Error Message      DEVICE_TEST-4-THREAD_CREATE_FAIL: Thread creation failed 

Explanation    Device Test process could not create threads

Recommended Action    No action is required.

Error Message      DEVICE_TEST-4-TIMER_CREATE_FAIL: Timer creation failed 

Explanation    Device Test process could not create timer

Recommended Action    No action is required.

Error Message      DEVICE_TEST-4-TIMER_START_FAIL: Timer start failed 

Explanation    Device Test process could not start timer

Recommended Action    No action is required.

DEVICE_TEST-5

Error Message      DEVICE_TEST-5-NOTICE_TEST: Memory allocation failed notice 

Explanation    Device Test process could not allocate memory

Recommended Action    No action is required.

DEVICE_TEST-6

Error Message      DEVICE_TEST-6-INFO_TEST: Memory allocation failed info 

Explanation    Device Test process could not allocate memory

Recommended Action    No action is required.

DEV_LOG Messages

DEV_LOG-3

Error Message      DEV_LOG-3-ERROR: [chars] 

Explanation    Dev_log_lc encountered an error

Recommended Action    No action is required.

DEV_LOG-SLOT#-4

Error Message      DEV_LOG-SLOT#-4-DEV_LOG_LC_ERROR: [chars] 

Explanation    Dev_log_lc encountered an error

Recommended Action    No action is required.

DFTM Messages

DFTM-SLOT#-2

Error Message      DFTM-SLOT#-2-DFTM_INTF_NOT_FOUND: Interface [chars] not found in 
DFTM database [chars] 

Explanation    DFTM database doesnthavetheinterface.'

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-2-DFTM_INVALID_FTAG_NUM: DFTM received invalid number of 
FTags [dec] from M2RIB 

Explanation    DFTM recvd invalid number of FTags from M2RIB.

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-2-DFTM_INVALID_INTF_NUM: DFTM has invalid number of 
interfaces [dec] in the DB 

Explanation    DFTM has invalid number of interfaces in the DB.

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-2-DFTM_PC_NUM_MEMB_INVALID: DFTM received invalid number 
of PC members [dec] from ELTM 

Explanation    DFTM recvd invalid number of PC members from ELTM.

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-2-DFTM_VLAN_NOT_FOUND: VLAN [dec] not found in DFTM 
database [chars] 

Explanation    DFTM database doesnthavetheVLAN.'

Recommended Action    No action is required.

DFTM-SLOT#-3

Error Message      DFTM-SLOT#-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB 
Entry 

Explanation    DFTM failed to program BDDB Entry

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table 
Entry 

Explanation    DFTM failed to program BD Table Entry

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_LAYER: Invalid Port Layer 
Received for interface: [chars] 

Explanation    Invalid Port Layer Received for interface

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_MODE: Invalid Port Mode 
Received for interface: [chars] 

Explanation    Invalid Port Mode Received for interface

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_TYPE: Invalid Port Type 
Received for interface: [chars] 

Explanation    Invalid Port Type Received for interface

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_IFIDX_TYPE_ERROR: Failed to get type for 
interface: [chars] 

Explanation    Failed to get type for the interface

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_INVALID_PRIM_SEC_VLAN_REQ: DFTM received prim-sec 
request for a non-exiting sec vlan [dec] on primary [dec] 

Explanation    DFTM recvd prim-sec vlan mapping request for a non-existing sec vlan on prim vlan

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 
Consistency Table Entry 

Explanation    DFTM failed to program L2L3 Consistency Table Entry

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast 
FTag Table Entry 

Explanation    DFTM failed to program Multicast Ftag Table Entry

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT 
Table Entry 

Explanation    DFTM failed to program SGT DGT Table Entry

Recommended Action    No action is required.

Error Message      DFTM-SLOT#-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN 
Translation Table Entry for vlan [dec], xlt_vlan [dec] on fe [dec] 

Explanation    DFTM failed to program VLAN Translation Table

Recommended Action    No action is required.

DHCP_SNOOP Messages

DHCP_SNOOP-2

Error Message      DHCP_SNOOP-2-DHCP_SNOOP_PROGRAM_EXIT: [chars] 

Explanation    DHCP snoop process did an abnormal exit

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-2-INITFAIL: DHCP Daemon Initialization failed: [chars] 

Explanation    DHCP Daemon Initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-2-PSSERROR: [chars] 

Explanation    DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-2-REGPARTREE: Unable to register par tree: [chars] 

Explanation    Could not register par tree. [chars] explains the reason for the failure.

Recommended Action    No action is required.

DHCP_SNOOP-3

Error Message      DHCP_SNOOP-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-ASSERTION_FAILED: [chars]:[dec] 

Explanation    DHCP Snoop process has hit an assert condition at file [chars] line number [dec]

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-DHCPDENIEDARP: ARP frame denied due to DHCP snooping 
binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target 
mac [chars] target ip [chars]. 

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-DHCPRATELIMIT: Interface [chars] has been error 
disabled due to excessive ingress rate [dec] of DHCP packets. 

Explanation    [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-HWPGMFAILURE: Hardware programming has failed: [chars] 

Explanation    Hardware programming has failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-INVDHCPPKTS: Validation errors while processing DHCP 
packet received on interface [chars] vlan [dec] Reason:[chars]. Dropping the 
packet 

Explanation    Validation errors DHCP packet receieved on the interface [chars] vlan [[dec]]. Reason:[chars]

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-MTSERROR: [chars] 

Explanation    DHCP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-PKTDROP: Packet dropped. Reason - [chars] 

Explanation    Dropping the packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-PKTRECVFAIL: Failed to receive packet - [chars] 

Explanation    Failed to receive packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-PKTSENDFAIL: Failed to send packet, - [chars] 

Explanation    Failed to send packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-SOCKBINDFAIL: Failed to bind to raw socket - [chars] 

Explanation    Failed to bind to socket. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-3-SOCKOPENFAIL: Failed to open socket for receiving DHCP 
packets - [chars] 

Explanation    An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.

Recommended Action    No action is required.

DHCP_SNOOP-4

Error Message      DHCP_SNOOP-4-ACL_DENY: [dec] Invalid ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]])

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-4-DHCP_SNOOPING_DENY: [dec] Invalid ARP messages 
([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]])

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-4-ERROR_DISABLED: Interface [chars] has moved to error 
disabled state due to excessive rate [dec] of ingress ARP packets 

Explanation    Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-4-INVALID_ARP: [dec] Invalid ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]])

Recommended Action    No action is required.

DHCP_SNOOP-5

Error Message      DHCP_SNOOP-5-ACL_PERMIT: [dec] ARP messages ([chars]) on [chars], 
vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]])

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-5-DHCPHOSTADD: A new Host is [chars] connected to 
interface [chars] in VLAN [dec] and is allocated IP address [chars] for [dec] secs. 

Explanation    A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-5-DHCPLEASEEXPIRE: Lease expired for host [chars] having 
IP address [chars] connected to interface [chars] in VLAN [dec] for lease [dec] 
secs. 

Explanation    The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-5-DHCP_SNOOPING_PERMIT: [dec] ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]])

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-5-VLANDISABLE: DHCP Snooping disabled on vlan [dec] 

Explanation    DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-5-VLANENABLE: DHCP Snooping enabled on vlan [dec] 

Explanation    DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan. This is an informational message.

Recommended Action    No action is required.

DHCP_SNOOP-6

Error Message      DHCP_SNOOP-6-DAIVLANDISABLE: DAI disabled on vlan [dec] 

Explanation    Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DAIVLANENABLE: DAI enabled on vlan [dec] 

Explanation    Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DHCPBINDSYNC: Binding entry with MAC [chars] interface 
[chars] VLAN [dec] IP address [chars] and lease time [dec] secs is synced. 

Explanation    Binding entry identified by [chars] has been synced. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DHCPEXIT: DHCP Daemon shutting down gracefully. 

Explanation    DHCP Daemon is shutting down gracefully. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DHCPPERMITTEDARP: ARP frame permitted due to DHCP 
snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip 
[chars] target mac [chars] target ip [chars]. 

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DHCPPKTFWD: Gracefully forwarding DHCP packet. Reason: 
[chars] 

Explanation    Gracefully forwarding DHCP packet. reason [chars]

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-DHCPUP: DHCP Daemon Up. 

Explanation    DHCP Daemon was created successfully and is up and running. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-INFO: [chars] 

Explanation    An event during switchover. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-INTFDISABLE: IP Src Guard disabled on intf [chars] 

Explanation    IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-INTFENABLE: IP Src Guard enabled on intf [chars] 

Explanation    IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf. This is an informational message.

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-NONDHCPPKTFWD: Non DHCP packet with src port:[dec] dst 
port:[dec] on intf:[chars] vlan:[dec]. Forwarding on [chars] 

Explanation    Non DHCP packet arrived with UDP src/dst ports [dec], [dec] on interface [chars], vlan [dec]. Forwarding the packet on [chars]

Recommended Action    No action is required.

Error Message      DHCP_SNOOP-6-OPT82INSTFAIL: [chars] [chars] 

Explanation    Insertion of Option82 suboptions failed. [chars] tells the failure. [chars] explains the reason for failure. This is an informational message.

Recommended Action    No action is required.

DIAGCLIENT Messages

DIAGCLIENT-2

Error Message      DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE: Module <[dec]

Explanation    Bootup Test completed

Recommended Action    Nothing to be done if the test reports SUCCESS otherwise copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information

Error Message      DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN: Test <[chars]

Explanation    Informational Syslog

Recommended Action    No action is required.

Error Message      DIAGCLIENT-2-PSS_READ_FAILURE: Read from PSS failed on Module <[dec]

Explanation    Read operation from PSS store failed

Recommended Action    No action is required.

Error Message      DIAGCLIENT-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]

Explanation    Write operation on PSS store failed

Recommended Action    No action is required.

DIAGCLIENT-3

Error Message      DIAGCLIENT-3-DIAG_HM_FAIL: Module <[dec]

Explanation    A Health Monitoring Test has reported failure

Recommended Action    Ensure the line card is firmly in the slot, reseat if necessary, and attempt to run the test again if the line card is not seated properly in the slot. If the line card was properly seated in the slot, copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.

Error Message      DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS: Module <[dec]

Explanation    Ondemand test has failed more than configured number of times

Recommended Action    Copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information

DIAGCLIENT-4

Error Message      DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT: Received LC offline event for 
the current slot:[dec]. Ignoring it 

Explanation    Informational Syslog

Recommended Action    No action is required.

Error Message      DIAGCLIENT-4-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], 
dest slot: [dec], dest SAP: [dec], error-id: [hex] 

Explanation    MTS send reports failure

Recommended Action    No action is required.

DIAGCLIENT-5

Error Message      DIAGCLIENT-5-CALLOC_FAILURE: Memory allocation failed 

Explanation    DiagClient process could not allocate memory

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-DIAG_ONDEMAND_TEST_FINISH: Module [dec]: Ondemand test 
[chars] finished 

Explanation    Informational Syslog

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-DIAG_ONDEMAND_TEST_START: Module [dec]: Ondemand test 
[chars] started 

Explanation    Informational Syslog

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-DIAG_ONDEMAND_TEST_STOP: Module [dec]: Ondemand test 
[chars] stopped 

Explanation    Informational Syslog

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-DIAG_SCHED_COMPLETE: Module <[dec]

Explanation    A scheduled Test was completed

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-ONDEMAND_FAIL: Module <[dec]

Explanation    The specified test has reported FAILURE in this Iteration

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-ONDEMAND_SUCCESS: Module <[dec]

Explanation    The specified test has reported SUCCESS in this Iteration

Recommended Action    No action is required.

Error Message      DIAGCLIENT-5-PER_PORT_TEST_FAIL: Module <[dec]

Explanation    Per Port Test has failed on the above all ports

Recommended Action    No action is required.

DIAGMGR Messages

DIAGMGR-2

Error Message      DIAGMGR-2-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest 
slot: [dec], dest SAP: [dec], error-id: [hex] 

Explanation    MTS send reports failure

Recommended Action    No action is required.

Error Message      DIAGMGR-2-PSS_DELETE_FAILURE: Read from PSS failed on Module <[dec]

Explanation    Read operation from PSS store failed

Recommended Action    No action is required.

Error Message      DIAGMGR-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]

Explanation    Write operation on PSS store failed

Recommended Action    No action is required.

DIAGMGR-3

Error Message      DIAGMGR-3-DIAG_MAJOR_DEFECT: Module <[dec]

Explanation    A major error was detected during diagnostic testing

Recommended Action    Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.

Error Message      DIAGMGR-3-DIAG_MINOR_DEFECT: Module <[dec]

Explanation    A minor error was detected during diagnostic testing

Recommended Action    Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information

Error Message      DIAGMGR-3-GET_CURR_SLOT_FAIL: Failed to get the current slot for the 
process. Error:[chars] 

Explanation    The process initialization failed to get the current slot.

Recommended Action    This is an informational message stating that a process initialization failure.

DIAGMGR-4

Error Message      DIAGMGR-4-CURR_SLOT_OFFLINE: Recevied an LC offline event for the 
current slot:[dec]. Ignoring it 

Explanation    The process received an offline event for the slot it is running. Ignoring it.

Recommended Action    This is an informational message stating that an unexpected event has been encountered.

Error Message      DIAGMGR-4-DISRPT_TST_START: Starting Test <[chars]

Explanation    Starting a Disruptive Test can disturb the systemsnormalfunctionality'

Recommended Action    Reset target module

Error Message      DIAGMGR-4-FIXED_INTRVL_CHANGED: The users are not allowed to change 
monitoring interval of Test <[chars]

Explanation    The specified health monitoring test interval is not user-configurable and therefore cannot be changed

Recommended Action    Nothing. The specific health monitoring interval is not user- configurable by design so nothing can be done to change the interval

DIAGMGR-5

Error Message      DIAGMGR-5-BOOTUP_CONF: Diagnostic Bootup Level: <[chars]

Explanation    Current Diagnostic BootUp Level being configure or changed

Recommended Action    No action is required.

Error Message      DIAGMGR-5-CALLOC_FAILURE: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed

Recommended Action    No action is required.

Error Message      DIAGMGR-5-CHANGE_ALWAYS_HM: Health Monitoring test <[chars]

Explanation    The specified health monitoring test must be run and cannot be disabled

Recommended Action    Nothing. The specific health monitoring test cannot be disabled by design. The system is working properly.

Error Message      DIAGMGR-5-HM_START: Health monitoring test <[chars]

Explanation    Health Monitoring Test started

Recommended Action    No action is required.

Error Message      DIAGMGR-5-HM_STOP: Disabling health monitoring test <[chars]

Explanation    Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command

Recommended Action    No action is required.

Error Message      DIAGMGR-5-INTRVL_INCORRECT: Monitoring Interval is less than minimum 
of [dec] seconds required for Module <[dec]

Explanation    Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set

Recommended Action    The system is working properly and no user action is required. If you want to specify a smaller testing interval, the error message text provides the lowest possible configurable interval for the specified monitoring interval

Error Message      DIAGMGR-5-MODULE_MISSING: Diagnostic command issued on non-existing 
Module <[dec]

Explanation    A line card could not be located in a slot where a diagnostic action was requested

Recommended Action    Ensure the targeted line card is properly seated in the specified slot. If the line card is properly seated, ensure the correct slot was indicated in the command-line interface. If the line card is well-seated and the correct slot was specified, copy the error message exactly as it appears on the screen as well as the output of show tech-support and paste the output into a separate file. Contact your technical support representative with the gathered information

Error Message      DIAGMGR-5-NONHM_AS_HM: The Test <[chars]

Explanation    Non-HM test cannot be scheduled to run as a Health Monitoring test

Recommended Action    No action is required.

DIAGMGR-6

Error Message      DIAGMGR-6-BOOTUP_DIAG_OK: Module <[dec]

Explanation    The diagnostic tests did not detect any error on the card.

Recommended Action    This is an informational message stating that the line card passed the diagnostic tests.

Error Message      DIAGMGR-6-BOOTUP_TEST_STARTED: Module <[dec]

Explanation    Starting bootup testing for above module

Recommended Action    No action is required.

DIAG_PORT_LB Messages

DIAG_PORT_LB-2

Error Message      DIAG_PORT_LB-2-FIPS_RANDOM_ERROR: Random Number Generation Failure 

Explanation    Random Number genration failed in FIPS module

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE: LC Inserted request response 
send to Module Manager failed . Error:[chars] 

Explanation    Failed to send the response for LC insertion to Module Manager.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-LIF_GET_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed to get Diagnostic LIF id

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-MALLOC_FAILURE: [chars]([dec]) Memory allocation 
failed. 

Explanation    Port Loopback test process could not allocate memory

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL: Module:[dec] 
Test:PortLoopback failed [dec] consecutive times. Faulty module:[chars] [chars] 
Error:[chars] 

Explanation    PortLoopback test failed on the module consecutively

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-PROC_INIT_FAILURE: [chars]([dec]) [chars] 
Error:[chars] 

Explanation    Port Loopback test process failed in process initialization

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] 
Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[chars] 
[chars] Error:[chars] 

Explanation    Rewrite Engine Loopback test failed on the module consecutively

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-2-SNAKE_TEST_LOOPBACK_TEST_FAIL: Module:[dec] 
Test:SnakeLoopback failed [dec] consecutive times. Faulty module:[chars] affected 
ports:[chars] Error:[chars] 

Explanation    Snake test failed on the module consecutively

Recommended Action    No action is required.

DIAG_PORT_LB-3

Error Message      DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE: [chars]. Module:[dec] 
Error:[chars]. 

Explanation    Forwarding path setup for port loopback tests failed

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-DIAG_PKT_SEND_FAILURE: [chars]([dec]) [chars]. 
Error:[chars] 

Explanation    Port Loopback test process failed to send loopback packets.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-FSM_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars] 

Explanation    Port Loopback test process failed in MTS API.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-GET_DIAG_BD_FAIL: [chars]([dec]) Failed to get the BD 
for Diag VLAN:[dec]. Error:[chars]. 

Explanation    Failed to get the BD corresponding to the Diag VLAN

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-IFINDEX_LIB_FAILURE: [chars]([dec]) [chars] 
[chars]:[hex] [chars] [chars] 

Explanation    Port Loopback test process failed in if_index library API

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-INVALID_TEST_REQUEST: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to get test request info.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-INVALID_TEST_RUN: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to get the current test run information

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-PDB_LIB_API_ERROR: Failed to [chars]. Error:[dec]. 

Explanation    The port loopback test was not able to get chassis info

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-PIXM_LIB_ERROR: [chars]([dec]) Failed to convert 
[chars]:[hex] to [chars]. Error:[chars] 

Explanation    Port Loopback test process failed to convert port ifindex <-

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-PORT_CLIENT_LIB_ERROR: [chars]([dec]) [chars]. 
Error:[chars] 

Explanation    Port Loopback test process failed in Port Client API.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-RESULT_ADD_FAILURE: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to add the port test result

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-RESULT_SEND_FAILURE: [chars]([dec]) [chars] 

Explanation    Port Loopback test process failed to send the test results

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL: 
Module:[dec] Test:RewriteEngine Loopback Spine path:[dec] failed [dec] 
consecutive times. Error:[chars] 

Explanation    Rewrite Engine Loopback test failed on the spine path consecutively

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-SOCKET_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed in socket operations

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-STATS_LIB_ERROR: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed in stats infra lib API.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-TEST_RES_SEND_FAIL: Failed to send [chars] test 
results back to Diagnostics Infrastucture. Error:[chars]. 

Explanation    The port loopback test was not able to send the test results

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-TIMER_LIB_ERROR: [chars]([dec]) [chars] 

Explanation    Port Loopback test process timer handling failure.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-VLAN_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed to get Diagnostic VLAN info

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-VQI_GET_FAIL: Failed to get the Diag VQi from XBM. 
Error:[chars] 

Explanation    Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL: Failed to conigure the XBAR mask 
while running the RewriteEngineLoopback test. Error:[chars]. Module:[dec] could 
have gone offline 

Explanation    Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline

Recommended Action    No action is required.

DIAG_PORT_LB-4

Error Message      DIAG_PORT_LB-4-MTS_LIB_ERROR: [chars]([dec]) [chars]. 
Warning:[chars] 

Explanation    Port Loopback test process failed in MTS API.

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-4-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send 
request to configure port ifindex:[dec] for port loopback test 

Explanation    Failed to configure/restore the port to do/cleanup port loopback testing

Recommended Action    No action is required.

DIAG_PORT_LB-5

Error Message      DIAG_PORT_LB-5-DIAG_PORT_LB_DISABLED: DIAG_PORT_LB Disabled 

Explanation    DIAG_PORT_LB Service Disabled

Recommended Action    No action is required.

Error Message      DIAG_PORT_LB-5-DIAG_PORT_LB_ENABLED: DIAG_PORT_LB Enabled 

Explanation    DIAG_PORT_LB Service nabled

Recommended Action    No action is required.

DMM Messages

DMM-SLOT#-5

Error Message      DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_SRVR_ZONE: Job Id:%Ld VSAN :[dec] 
New N-Port FCID :[hex] Server FCID:[hex] are in the same zone. ALERT!! 

Explanation    A New N-Port has come up which is zoned in the same zone as the Server

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_STG_ZONE: Job Id:%Ld VSAN :[dec] 
New N-Port FCID :[hex] Storage FCID:[hex] are in the same zone. ALERT!! 

Explanation    A New N-Port has come up which is zoned in the same zone as the Storage

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_ERR_DMM_SRVR_RSCN: Job Id:%Ld Server N-Port 
pWWN:0x%Lx [chars] 

Explanation    An RSCN event was received for the Server associated with a Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_ERR_DMM_STG_RSCN: Job Id:%Ld N-Port pWWN:0x%Lx 
Storage:[chars] [chars] 

Explanation    An RSCN event was received for the Storage associated with a Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_COMPLETE: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the completion of a Data Migration Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR_LOST_SSM_PEER_CONNECTION: Job 
Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job due to loss in ip connectivity to peer ssm

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_FINISH: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating Finish-request for a Method-2 Data Migration Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_START: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the start of a Data Migration Job

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_STOP: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating that the Data Migration Job was stopped by Administrator

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_TCP_CONNECTION_DOWN: Job Id:%Ld lost 
connection to peer [chars]. Job may be RESET 

Explanation    Event indicating IP Connectivity loss to peer SSM. Affected Job maybe be RESET

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_COMPLETE: Job Id:%Ld 
NumSession:[dec] 

Explanation    Event indicating the completion of a Data Migration Job Verification

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_ERROR: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job Verification due to an error

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_START: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the start of a Data Migration Job Verification

Recommended Action    No action is required.

Error Message      DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_STOP: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job Verification by the user

Recommended Action    No action is required.

DOT1X Messages

DOT1X-2

Error Message      DOT1X-2-DOT1X_INIT: Dot1x unable to start 

Explanation    The system failed to create the Dot1x process

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

DOT1X-3

Error Message      DOT1X-3-ERR_SPANDST: It is configured as a SPAN Dest port. 

Explanation    Dot1x and SPAN Dest ports are mutually exclusive features.

Recommended Action    Disable SPAN destination port configuration first before reconfiguring Dot1x on the port.

Error Message      DOT1X-3-INVALID_INPUT: Invalid on interface [chars]. 

Explanation    The Dot1x interface parameter is out of the specified range or is invalid.

Recommended Action    Refer to the CLI help documentation to determine the valid 802.1x parameters.

Error Message      DOT1X-3-MEM_UNAVAIL: perform the 802.1X action. 

Explanation    Insufficient system memory is available to perform the Dot1x Authentication.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message      DOT1X-3-NOT_DOT1X_CAPABLE: [chars]. 

Explanation    Dot1x Authentication can only be enabled on physical Ethernet interfaces.

Recommended Action    Enable Dot1x Authentication on physical Ethernet interfaces only.

Error Message      DOT1X-3-SECURE_MAC_INSERT_FAILED: address [chars] could not be 
secured on interface [chars] 

Explanation    The interface specified in the error message could not secured supplicant mac. The port has been Error disabled.

Recommended Action    Mac address could not be added into mac address table. Enter the <Cmd

Error Message      DOT1X-3-SECURITY_VIOLATION: New MAC address [chars] is seen on 
interface [chars] in [chars] mode 

Explanation    The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.

Recommended Action    Ensure that the port is configured to use only one host. Enter the <Cmd

Error Message      DOT1X-3-SM_INIT: Internal error while initializing state machine 
[chars], state [chars]: [chars] 

Explanation    An attempt was made to initialize an invalid state machine.

Recommended Action    Initialize dot1x state machine

DOT1X-4

Error Message      DOT1X-4-BADEVENT: Event [chars] is invalid for the current state 
[chars]: [chars] [chars] 

Explanation    An attempt was made to post an event to a state machine that is invalid for the current state.

Recommended Action    Initialize dot1x state machine

Error Message      DOT1X-4-MAB_DISABLED_ON_PCM: Interface [chars] is a member of 
portchannel, MAB is not supported on this port 

Explanation    MAB is not supported on portchannel member port

Recommended Action    To enable MAB make sure that port is not member of portchannel

Error Message      DOT1X-4-MAB_DISABLED: Interface [chars] is in Trunk mode, MAB is not 
supported on this port 

Explanation    MAB is not supported on Trunk port

Recommended Action    To enable MAB make sure that port is not in trunk mode

Error Message      DOT1X-4-MULTIHOST_ON_PCM: Interface [chars] is a member of 
portchannel, dot1x host mode will be multi-host and changing it to single-host 
mode wontbesupported'

Explanation    Current Port is a member of portchannel, so dot1x host mode has to be in multi-host mode.

Recommended Action    To change host mode, ensure that port is not a member of portchannel

Error Message      DOT1X-4-PSEC_ON_PCM: Interface [chars] is a member port or 
portchannel interface with port security configration 

Explanation    Dot1x is not supported on member ports or port channel with port security configuration

Recommended Action    Remove port security configuration on the member port or port channel interface

Error Message      DOT1X-4-STOPPED: Event [chars] ignored because the state machine is 
stopped: [chars] [chars] 

Explanation    An attempted was made to post an event to a state machine that has already been stopped.

Recommended Action    An internal error has occurred with the state machine. The traceback should indicate the guilty party.

Error Message      DOT1X-4-TO_MULTIHOST: Interface [chars] is in trunk mode, dot1x host 
mode will be multi-host and changing it to single-host mode wontbesupported'

Explanation    Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.

Recommended Action    To change host mode, ensure that port is not in trunk mode

DOT1X-5

Error Message      DOT1X-5-DOT1X_DISABLED: dot1x Disabled 

Explanation    Dot1x Service Disabled

Recommended Action    No action is required.

Error Message      DOT1X-5-DOT1X_ENABLED: dot1x Enabled 

Explanation    Dot1x Service Enabled

Recommended Action    No action is required.

Error Message      DOT1X-5-DOT1X_NOTIF: [chars] 

Explanation    Dot1x Notification

Recommended Action    No action is required.

Error Message      DOT1X-5-INVALID_MAC: broadcast or multicast mac address) [chars] is 
trying to authenticate. 

Explanation    Authentication using 802.1x is not allowed for zero, broadcast, and multicast source MAC addresses.

Recommended Action    Connect a Dot1x supported Host to the Dot1x enabled port.

Error Message      DOT1X-5-PAC_STATUS: PAC provisioning for the server [chars] through 
the vrf [chars] [chars] 

Explanation    PAC provisioning status

Recommended Action    No action is required.

Error Message      DOT1X-5-SESSION_CREATION: Dot1x authentication session initiated in 
interface [chars] using authentication method [chars] 

Explanation    Dot1x authentication session has been created after successful authentication of supplicant

Recommended Action    No action is required.

Error Message      DOT1X-5-SESSION_TERMINATION: Dot1x authentication session in 
interface [chars] using authentication method [chars] is terminated because of 
[chars] and port moved to [chars] state 

Explanation    Dot1x authentication session has been terminated

Recommended Action    No action is required.

Error Message      DOT1X-5-STATUS: Dot1x interface [chars] status changed from [chars] 
to [chars] 

Explanation    Dot1x authenticator has changed its internal state

Recommended Action    No action is required.

DPP_DEBUG Messages

DPP_DEBUG-2

Error Message      DPP_DEBUG-2-DPP_CRIT: [DPP[dec]] [chars] 

Explanation    A DPP generated a critical message

Recommended Action    No action is required.

DPVM Messages

DPVM-2

Error Message      DPVM-2-ALLOC_FAILED: Memory allocation failed for size:[dec] for 
[chars] 

Explanation    Memory allocation failed for size [dec] for [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DPVM-2-DPVM_DUPL_REJECT: [chars] 

Explanation    Rejected duplicate pwwn query

Recommended Action    Dpvm overwrite-duplicate-pwwn

DPVM-3

Error Message      DPVM-3-DB_ERR: [chars] 

Explanation    An error occured during an DPVM database operation. [chars] indicates the reason for the error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DPVM-3-DDAS_MODE_INVALID: [chars] 

Explanation    DDAS mode Invalid. [chars]

Recommended Action    Flip DDAS mode

Error Message      DPVM-3-INIT_FAIL: [chars] 

Explanation    An error happened during DPVM Initialization. [chars] indicates the reason for failure

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DPVM-3-MTS_ERR: [chars] 

Explanation    An error occured in processing of an MTS message. [chars] indicates the error that occured

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      DPVM-3-PSS_ERR: [chars] 

Explanation    An error occured during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

DPVM-4

Error Message      DPVM-4-ACTIVATION_FAIL: [chars] 

Explanation    Activation of DPVM device mappings failed due to [chars]

Recommended Action    Correct the error and reactivate database again

Error Message      DPVM-4-FEATURE_DISABLED: [chars] 

Explanation    DPVM is unavailable and disabled now

Recommended Action    No action is required.

DPVM-6

Error Message      DPVM-6-FEATURE_ENABLED: [chars] 

Explanation    DPVM is available and enabled now

Recommended Action    No action is required.

Error Message      DPVM-6-INFO: [chars] 

Explanation    An event happened that affects DPVM. [chars] indicates the event

Recommended Action    No action is required.

DSTATS Messages

DSTATS-2

Error Message      DSTATS-2-PSS_INIT_FAIL: pss initialization failed due to error: [hex] 

Explanation    Dstats process pss initialization failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

DSTATS-3

Error Message      DSTATS-3-PSS_CREATE_FAIL: pss create runtime database failed due to 
error: [hex] 

Explanation    Dstats process pss create runtime database failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_DELETE_FAIL: pss delete runtime entry key:[hex] failed 
due to error: [hex] 

Explanation    Dstats process pss delete runtime entry key [hex] failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_MAX_KEY_FAIL: pss set runtime max key failed due to 
error: [hex] 

Explanation    Dstats process pss set runtime max key failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_MAX_VALUE_FAIL: pss set runtime max value failed due to 
error: [hex] 

Explanation    Dstats process pss set runtime max value failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_OPEN_FAIL: pss open runtime database failed due to 
error: [hex] 

Explanation    Dstats process pss open runtime database failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_RELOAD_FAIL: pss reload runtime database failed due to 
error: [hex] 

Explanation    Dstats process pss reload runtime database failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_SNAPSHOT_DEBUG_FAIL: pss snapshot runtime debug to 
uri:[chars] failed due to error: [hex] 

Explanation    Dstats process pss snapshot of runtime debug to uri [string] failed due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_SNAPSHOT_FAIL: pss snapshot runtime to uri:[chars] 
failed due to error: [hex] 

Explanation    Dstats process pss snapshot of runtime to uri [string] failed due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

Error Message      DSTATS-3-PSS_STORE_FAIL: pss store runtime entry key:[hex] val:[hex] 
failed due to error: [hex] 

Explanation    Dstats process pss store runtime entry key [hex] value [hex] failure due to error [hex].

Recommended Action    Collect more information using command showflash'.Seepsssystemerrorcodesforreason.'

ELTMC Messages

ELTMC-SLOT#-2

Error Message      ELTMC-SLOT#-2-ELTMC_INTERFACE_INTERNAL_ERROR: Internal error: 
[chars]:[chars], collect output of show tech-support eltm 

Explanation    ELTM hit a internal error. Collect show tech-support eltm for futher analysis.

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_INTERNAL_ERROR: Internal error: [chars], collect 
output of show tech-support eltm 

Explanation    ELTM hit a internal error. Collect show tech-support eltm for futher analysis.

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_INTF_NOT_FOUND: Interface [chars] not found in 
ELTM database [chars] 

Explanation    ELTM database doesnthavetheinterface.'

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_INTF_NOT_SUPP: Interface [chars] not supported 
by ELTM [chars] 

Explanation    ELTM doesntsupporttheinterfaceforthespecifiedoperation'

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_INTF_TO_LTL: Failed to get LTL for interface 
[chars] return status [chars] 

Explanation    ELTM Failed to get LTL for interface. Packets received on this interface might not be handled correctly by the forwarding engine

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_INTF_TO_SLOT: Failed to get slot for interface 
[chars] return status [chars] 

Explanation    ELTM Failed to get Slot for interface. Port-channels and L2 Learning might be effected

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_L2_LIF_ALLOC_FAIL_INTF: Failed to allocate L2 
LIF entries in forwarding engine for interfac [chars] 

Explanation    ELTM Failed to allocate L2 LIF entries in forwarding engine. This will effect Layer 2 and Layer 3 forwarding for the interface

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_L2_LIF_ALLOC_FAIL_VDC: Failed to allocate L2 LIF 
entries in forwarding engine 

Explanation    ELTM Failed to allocate L2 LIF entries in forwarding engine. This will effect Layer 2 and Layer 3 forwarding in this VDC

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_L3_INGRESS_LIF_ALLOC_FAIL_INTF: Failed to 
allocate L3 Ingress LIF entries in forwarding engine for interfac [chars] 

Explanation    ELTM Failed to allocate L3 Ingress LIF entries in forwarding engine. This will effect Layer 3 forwarding for the interface

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_RSVD_VLAN: Failed to get the reserved vlans. 
Failed with error [chars] 

Explanation    ELTM Failed to get the reserved vlans.ThiswilleffectmulticastforwardingonSVIinterfaces'

Recommended Action    No action is required.

Error Message      ELTMC-SLOT#-2-ELTMC_VLAN_INTERNAL_ERROR: Internal error: VLAN 
[dec]:[chars], collect output of show tech-support eltm 

Explanation    ELTM hit a internal error. Collect show tech-support eltm for futher analysis.

Recommended Action    No action is required.

ELTM Messages

ELTM-2

Error Message      ELTM-2-INTERFACE_INTERNAL_ERROR: Internal error: [chars]:[chars], 
collect output of show tech-support eltm 

Explanation    ELTM hit a internal error. Collect show tech-support eltm for futher analysis.

Recommended Action    No action is required.

Error Message      ELTM-2-INTERNAL_ERROR: Internal error: [chars], collect output of 
show tech-support eltm 

Explanation    ELTM hit a internal error. Collect show tech-support eltm for futher analysis.

Recommended Action    No action is required.

Error Message      ELTM-2-INTF_NOT_FOUND: Interface [chars] not found in ELTM database 
[chars] 

Explanation    ELTM database doesnthavetheinterface.'

Recommended Action    No action is required.

Error Message      ELTM-2-INTF_NOT_SUPP: Interface [chars] not supported by ELTM [chars] 

Explanation    ELTM doesntsupporttheinterfaceforthespecifiedoperation'

Recommended Action    No action is required.

Error Message      ELTM-2-INTF_TO_LTL: Failed to get LTL for interface [chars] return 
status [chars] 

Explanation    ELTM Failed to get LTL for interface. Packets received on this interface might not be handled correctly by the forwarding engine

Recommended Action    No action is required.

ELTM-5

Error Message      ELTM-5-EXT_COMP_ERR: [chars] component error [chars] 

Explanation    Recently applied Multicast config on the interface was unsuccessful, so reverting to the old state (before config)

Recommended Action    No action is required.

ELTM-6

Error Message      ELTM-6-ELTM_MTS_SEND_FAILED: Failed to send MTS message errno [hex] 
opcode [dec] 

Explanation    No action is required.

Recommended Action    Eltm

EOU Messages

EOU-2

Error Message      EOU-2-PBACL_APPLICATION_FAILURE: [chars] of host [chars] to/from 
pbacl group [chars] failed. Error : [chars] 

Explanation    Failure of host addition/deletion to/from pbacl group

Recommended Action    Please verify the addition/deletion of the host using the cli "show object-group". If it was a delete request that failed, manual deletion of the host from the group is recommended

EOU-5

Error Message      EOU-5-L2NAC_DISABLED: EOU Disabled 

Explanation    Service EOU Disabled

Recommended Action    No action is required.

Error Message      EOU-5-L2NAC_ENABLED: EOU Enabled 

Explanation    Service EOU enabled

Recommended Action    No action is required.

EOU-6

Error Message      EOU-6-AAA_DOWN: Default Policy ip: [chars]:retained 

Explanation    Policy retained

Recommended Action    No action is required.

Error Message      EOU-6-AUTHTYPE: Authtype: ip: [chars] Authtype:[chars] 

Explanation    Authentication type

Recommended Action    No action is required.

Error Message      EOU-6-BAD_PKT: Bad Packet: ip: [chars] Why: [chars] 

Explanation    Bad Packet because of reason specified

Recommended Action    No action is required.

Error Message      EOU-6-CTA: CTA: ip: [chars] status(detected/not detected): [chars] 

Explanation    CTA detected or not

Recommended Action    No action is required.

Error Message      EOU-6-IDENTITY_MATCH: Identity Match: ip: [chars] Policy: [chars] 

Explanation    Identity Matched or not

Recommended Action    No action is required.

Error Message      EOU-6-PBACL_APPLICATION_STATUS: [chars] of host [chars] to/from 
pbacl group [chars] succeeded 

Explanation    Status of host addition/deletion to pbacl group

Recommended Action    No action is required.

Error Message      EOU-6-POLICY: Policy on ip: [chars]: [chars]: [chars] 

Explanation    Policy applied

Recommended Action    No action is required.

Error Message      EOU-6-POSTURE: Posture:ip: [chars] Status: [chars], Interface: 
[chars] 

Explanation    Posture of host

Recommended Action    No action is required.

Error Message      EOU-6-SESSION: Session ip: [chars] Action:[chars] , Interface: 
[chars] 

Explanation    Session detected

Recommended Action    No action is required.

Error Message      EOU-6-SOCKET: Service eou on port: [dec] 

Explanation    Eou using above port

Recommended Action    No action is required.

Error Message      EOU-6-SQ_EAP_MSG: Status Query: ip: [chars] status: [chars] 

Explanation    Status query state

Recommended Action    No action is required.

Error Message      EOU-6-UNKN_EVENT_ERR: Unknow Event Err: ip: [chars] Message: [chars] 

Explanation    Error due to unknown event

Recommended Action    No action is required.

Error Message      EOU-6-VERSION_MISMATCH: Eou version mismatch ip: [chars] and version 
[dec] 

Explanation    Eou version mismatch

Recommended Action    No action is required.

EOU-7

Error Message      EOU-7-EOU_DISABLED_INTF: eou disabled on interface [chars] 

Explanation    Eou service disabled on interface

Recommended Action    No action is required.

Error Message      EOU-7-EOU_ENABLED_INTF: eou enabled on interface [chars] 

Explanation    Eou service enabled on interface

Recommended Action    No action is required.

EPLD_UPGRADE Messages

EPLD_UPGRADE-2

Error Message      EPLD_UPGRADE-2-ACTIVE_SINGLE_SUP_UPGRADE: install all epld does not 
upgrade Active Supervisor module [dec]. 

Explanation    Install all epld does not upgrade Active Supervisor in a switch with a single supervisor.

Recommended Action    No action is required.

Error Message      EPLD_UPGRADE-2-ACTIVE_SUP_UPGRADE: install all epld does not upgrade 
Active Supervisor module [dec]. Please do a switchover and upgrade the EPLDs on 
module [dec]. 

Explanation    Install all epld did not upgrade Active Supervisor.

Recommended Action    No action is required.

EPP Messages

EPP-5

Error Message      EPP-5-EPP_FAILURE: Interface [chars] EPP Failure 

Explanation    Trunk protocol failed

Recommended Action    showeppinternalevent-historyerr'willindicatetheerrorsencountered'

Error Message      EPP-5-EPP_LOOPBACK: Interface [chars] is looped back to the same 
switch 

Explanation    The interface is looped back to another interface on the same switch

Recommended Action    Check the connectivity of this interface and ensure that it is connected to another switch

Error Message      ETH-PORT-SEC-2-ETH_PORT_SEC_SECURITY_VIOLATION_ANOTHER_PORT: Host 
[chars] bound to Port [chars] in Vlan [dec] is trying to access Port [chars] in 
Vlan [dec] 

Explanation    Moved the port to violation state due to a mac address seen on one port being seen on another

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-2-ETH_PORT_SEC_SECURITY_VIOLATION_MAX_MAC_VLAN: Port 
[chars] moved to [chars] state as host [chars] is trying to access the port in 
vlan [dec] 

Explanation    Moved the port to violation state due to exceeding address count

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-2-ETH_PORT_SEC_SECURITY_VIOLATION: Triggered violation 
[chars] on Port [chars] 

Explanation    Violation action triggered on port due to security violation.

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_CONFIG_MAC_FAILED: Failed to configure 
MACs 

Explanation    Failed to configure MACs

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_INVALID_VLAN: Invalid VLAN configuration 

Explanation    Invalid VLAN configuration

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_PKTSENDFAIL: Failed to send packet, - 
[chars] 

Explanation    Failed to send packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_UNABLE_TO_DISABLE: Unable to disable 
eth_port_sec [chars]. 

Explanation    Unable to disable eth_port_sec Service

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_UNABLE_TO_ENABLE: Unable to enable 
eth_port_sec [chars]. 

Explanation    Unable to enable eth_port_sec Service

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-3-ETH_PORT_SEC_VIOL_UPDATE_FAILED: Failed to update 
violation mode 

Explanation    Failed to update violation mode

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_AGE_TIME_EXPIRY: Age Time expired for 
host [chars] in VLAN [dec] in port [chars] 

Explanation    Age time expired for host

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_DISABLED: eth_port_sec Disabled on 
if_index:[hex] 

Explanation    Eth_port_sec Service Disabled

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_DYNAMIC_MAC_ADDRESS_CLEARED: Dynamic 
MAC addresses for port [chars] cleared 

Explanation    Dynamic MAC address for port cleared

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_ENABLED: eth_port_sec Enabled on 
if_index:[hex] 

Explanation    Eth_port_sec Service Enabled

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_HOST_ADDITION: A new Host [chars] learnt 
on Port [chars] in Vlan [dec] 

Explanation    A new host is learnt on a port

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_HOST_DELETION: Host [chars] bound to 
secure port [chars] in Vlan [dec] has been removed 

Explanation    A host has been removed

Recommended Action    No action is required.

Error Message      ETH-PORT-SEC-5-ETH_PORT_SEC_INITFAIL: Eth Port Security 
Initialization failed: [chars] 

Explanation    Eth Port Security Initialization failed.[chars] explains the reason for the failure.

Recommended Action    No action is required.

ETHPORT Messages

ETHPORT-2

Error Message      ETHPORT-2-IF_CRITICAL_FAILURE: (Debug syslog)Critical failure: 
[chars], [chars] 

Explanation    There was a critical failure in the component.

Recommended Action    Please follow instructions on the syslog.

Error Message      ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface [chars] is down (Error 
disabled. Reason:[chars]) 

Explanation    The interface encountered an error while configuring it

Recommended Action    Collect more information about failed interface using command showportinternalallinterface[char]'.Inmostcases,youcanrecoverusinga'shutdown'followeda'noshutd own'ontheinterfaceorremovingandre-insertingthefibreopticcable.'

Error Message      ETHPORT-2-IF_ERROR_SHUT_LAN_NO_DCX: Shutting lan on interface 
[chars] that doesntconnecttoaDCBXcapableadaptor.'

Explanation    Shutting lan on interface that doesntconnecttoaDCBXcapableadaptor.'

Recommended Action    No action is required.

Error Message      ETHPORT-2-IF_SEQ_ERROR: Error ([chars]) communicating with [chars] 
for opcode [chars] ([chars]) - Ethpm 
didntreceiveaLinkUPfromthedriverontimeorhadaninternalerror,checkPortClientandEth
pmlogsanddebuginfo'

Explanation    Some component returned system error as a response to one of the port event sequence.

Recommended Action    None

Error Message      ETHPORT-2-SEQ_TIMEOUT: Component [chars] timed out on response to 
opcode [chars] ([chars]) 

Explanation    Some component did not respond to a request in stipulated time.

Recommended Action    None

Error Message      ETHPORT-2-SYSLOG_ETHPM_CRITICAL: Critical failure: [chars] 

Explanation    There was a critical failure in the component.

Recommended Action    Please collect system tech-support

ETHPORT-3

Error Message      ETHPORT-3-IF_DOWN_CHANNEL_ERR_DISABLED: Interface [chars] is down 
(Channel error disabled) 

Explanation    This interface belongs to a PortChannel and the PortChannel is error disabled

Recommended Action    Perform shut'and'noshutdown'onthePortChannelinterfacethatitbelongsto'

Error Message      ETHPORT-3-IF_ERROR_VLANS_REMOVED: VLANs [chars] on Interface [chars] 
are removed from suspended state. 

Explanation    The VLANs on an interface are being removed from the suspended state

Recommended Action    No action is required.

Error Message      ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs [chars] on Interface 
[chars] are being suspended. (Reason: [chars]) 

Explanation    The VLANs on an interface are being suspended due to some protocol action

Recommended Action    No action is required.

Error Message      ETHPORT-3-IF_NON_CISCO_TRANSCEIVER: Non-Cisco transceiver on 
interface [chars] is detected 

Explanation    The transceiver for the interface specified in the error message is not a Cisco module

Recommended Action    Replace the module with a compatible transceiver. If the transceiver was purchased from Cisco, please contact Cisco TAC to get the transceiver replaced

Error Message      ETHPORT-3-IF_SFP_ALARM: Interface [chars], [chars] 

Explanation    There was an alarm on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

Error Message      ETHPORT-3-IF_SFP_ERROR: Interface [chars], [chars] 

Explanation    There was an error on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

Error Message      ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER_VENDOR: Transceiver vendor 
([hex] [hex] [hex]) for interface [chars] is not supported 

Explanation    The transceiver vendor for the interface specified in the error message is not supported

Recommended Action    Replace the module with a compatible transceiver. If the transceiver was purchased from Cisco, please contact Cisco TAC to get the transceiver replaced

Error Message      ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface 
[chars] is not supported 

Explanation    The transceiver for the interface specified in the error message is not a Cisco supported module

Recommended Action    Replace the module with a compatible transceiver. If the transceiver was purchased from Cisco, please contact Cisco TAC to get the transceiver replaced

Error Message      ETHPORT-3-IF_XCVR_ALARM: Interface [chars], [chars] 

Explanation    There was an alarm on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

Error Message      ETHPORT-3-IF_XCVR_ERROR: Interface [chars], [chars] 

Explanation    There was an error on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

ETHPORT-4

Error Message      ETHPORT-4-IF_NON_QUALIFIED_TRANSCEIVER: Non-qualified transceiver on 
interface [chars] was detected 

Explanation    The transceiver for the interface specified has not been qualified on this platform for this software release

Recommended Action    Replace the module with a supported transceiver. Contact Cisco TAC to get platform transceiver qualification details

Error Message      ETHPORT-4-IF_SFP_WARNING: Interface [chars], [chars] 

Explanation    There was an warning on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

Error Message      ETHPORT-4-IF_XCVR_WARNING: Interface [chars], [chars] 

Explanation    There was an warning on the transceiver module

Recommended Action    Please do show interface transceiver details to obtain more information

ETHPORT-5

Error Message      ETHPORT-5-IF_ADMIN_UP: Interface [chars] is admin up [chars] 

Explanation    Interface is admin up

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_BANDWIDTH_CHANGE: Interface [chars],bandwidth changed 
to [chars] Kbit 

Explanation    Bandwidth of the interface has changed and this change is updated

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_ADMIN_DOWN: Interface [chars] is down 
(Administratively down) 

Explanation    Interface has been configured to be administratively down

Recommended Action    Perform noshutdown''

Error Message      ETHPORT-5-IF_DOWN_CFG_CHANGE: Interface [chars] is down(Config 
change) 

Explanation    FCIP interface temporarily down due to reconfiguration

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface [chars] is down 
(Channel admin down) 

Explanation    This interface belongs to a PortChannel and the PortChannel is configured to be administratively down

Recommended Action    Perform noshutdown'onthePortChannelinterfacethatitbelongsto'

Error Message      ETHPORT-5-IF_DOWN_CHANNEL_MEMBERSHIP_UPDATE_IN_PROGRESS: Interface 
[chars] is down (Channel membership update in progress) 

Explanation    The interface belongs to a PortChannel and a configuration is being attempted on the interface while there is a configuration in progress on the PortChannel

Recommended Action    Retry the configuration again

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_ADDR_ASSIGN_FAILURE_ISOLATION: Interface 
[chars] is down (Isolation due to domain id assignment failure) 

Explanation    Isolated due to a failure while assigning a domain

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_INVALID_RCF_RECEIVED: Interface [chars] is 
down (Isolation due to invalid fabric reconfiguration) 

Explanation    Invalid RCF received

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_MANAGER_DISABLED: Interface [chars] is down 
(Isolation due to domain manager disabled) 

Explanation    Isolated due to domain manager being disabled

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_MAX_RETRANSMISSION_FAILURE: Interface 
[chars] is down (Isolation due to domain manager other side not responding) 

Explanation    Remote end domain manager not responding

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_OTHER_SIDE_EPORT_ISOLATED: Interface 
[chars] is down (Isolation due to domain other side eport isolated) 

Explanation    Isolating this interface due to the remote end being isolated

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_DOMAIN_OVERLAP_ISOLATION: Interface [chars] is 
down (Isolation due to domain overlap) 

Explanation    Isolated due to domain overlap

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_ELP_FAILURE_ISOLATION: Interface [chars] is down 
(Isolation due to ELP failure) 

Explanation    ELP failed on the interface

Recommended Action    Check the output of showportinternalinfo'inthe'ELPfailurereason'field'

Error Message      ETHPORT-5-IF_DOWN_EPP_FAILURE: Interface [chars] is down (Error 
Disabled - EPP Failure) 

Explanation    Trunk protocol failed

Recommended Action    showportinternalevent-historymsgs'willindicatethetrunkprotocolexchangestodeterminewhyitfailed'

Error Message      ETHPORT-5-IF_DOWN_ESC_FAILURE_ISOLATION: Interface [chars] is down 
(Isolation due to ESC failure) 

Explanation    ESC failed on the interface

Recommended Action    Check the output of showportinternalevent-history'todeterminetheESCprotocolexchangestodeterminehowitfailed'

Error Message      ETHPORT-5-IF_DOWN_ETH_IF_DOWN: Interface [chars] is down(Tunnel port 
src interface down) 

Explanation    Ethernet link to which the FCIP interface is bound is down

Recommended Action    Ensure that the ethernet cable is connected, the interface is administratively enabled

Error Message      ETHPORT-5-IF_DOWN_ETH_LINK_DOWN: Interface [chars] is down(Tunnel 
port src interface link down) 

Explanation    Ethernet link to which the FCIP interface is bound is down

Recommended Action    Ensure that the ethernet cable is connected and the remote end is also active

Error Message      ETHPORT-5-IF_DOWN_FCOT_NOT_PRESENT: Interface [chars] is down (FCOT 
not present) 

Explanation    The FCOT has been removed

Recommended Action    Insert an FCOT

Error Message      ETHPORT-5-IF_DOWN_FCOT_VENDOR_NOT_SUPPORTED: Interface [chars] is 
down (Error disabled - Fcot vendor not supported) 

Explanation    Fcot inserted is not a supported one

Recommended Action    Please contact customer support for a list of authorized transceiver vendors

Error Message      ETHPORT-5-IF_DOWN_HW_FAILURE: Interface [chars] is down (Hardware 
Failure) 

Explanation    The moduleshardwarehasfailed'

Recommended Action    Collect more information about failed module using command showmoduleinternalallmodule''

Error Message      ETHPORT-5-IF_DOWN_INACTIVE: Interface [chars] is down (Inactive) 

Explanation    The port VSAN has been suspended or deleted

Recommended Action    Assign a new active port VSAN to the interface

Error Message      ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_MODE: Interface [chars] is down 
(Error disabled - Incompatible admin port mode) 

Explanation    The configured mode is not supported on this interface

Recommended Action    Perform a showportinternalinfo'todeterminethelistofmodessupportedonthisinterface'

Error Message      ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_RXBBCREDIT: Interface [chars] 
is down (Error disabled - Incompatible admin port rxbbcredit) 

Explanation    The configured receive B2B credit size is not supported

Recommended Action    Get the allowed receive B2B credit size from showportinternalinfo''

Error Message      ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_RXBUFSIZE: Interface [chars] is 
down (Error disabled - Incompatible admin port rxbufsize) 

Explanation    The configured receive buffer size is not supported

Recommended Action    Get the allowed receive buffer size from showportinternalinfo''

Error Message      ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_SPEED: Interface [chars] is 
down (Error disabled - Incompatible admin port speed) 

Explanation    The configured speed is not supported on this interface

Recommended Action    Perform a showportinternalinfo'todeterminetherangeofspeedsupportedonthisinterface'

Error Message      ETHPORT-5-IF_DOWN_INITIALIZING: Interface [chars] is down 
(Initializing) 

Explanation    The interface is in the process of coming up

Recommended Action    If the interface is stuck in this state for a while, check the output of showportinternalevent-history'todeterminewhatitiswaitingfor'

Error Message      ETHPORT-5-IF_DOWN_INTERFACE_REMOVED: Interface [chars] is down 
(Interface removed) 

Explanation    Interface removed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_L3_NOT_READY: Interface [chars] is down (L3 not 
ready) 

Explanation    System is not L3 ready: L3 license not found or router card not present

Recommended Action    Please check L3 license or router card

Error Message      ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface [chars] is down (Link 
failure) 

Explanation    The physical link has gone down

Recommended Action    Ensure that the cable is connected and the remote end is not shut down

Error Message      ETHPORT-5-IF_DOWN_LOOPBACK_DIAG_FAILURE: Interface [chars] is down 
(Diag failure) 

Explanation    Diag failed on the interface

Recommended Action    Collect more information about failed interface using command attachmodule'toconnecttomodule'

Error Message      ETHPORT-5-IF_DOWN_LOOPBACK_ISOLATION: Interface [chars] is down 
(Isolation due to port loopback to same switch) 

Explanation    The interface is looped back to another interface on the same switch

Recommended Action    Check the connectivity of this interface and ensure that it is connected to another switch

Error Message      ETHPORT-5-IF_DOWN_MODULE_REMOVED: Interface [chars] is down (module 
removed) 

Explanation    Interface is down because the module was removed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_NONE: Interface [chars] is down ([chars]) 

Explanation    Interface is down with a possible reason.

Recommended Action    Collect more information about port using command showportinternalinfo/event-history'todeterminewhyitwentdown'

Error Message      ETHPORT-5-IF_DOWN_NON_PARTICIPATING: Interface [chars] is down (Non 
participating) 

Explanation    The loop port has been put into non participating mode

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_OFFLINE: Interface [chars] is down (Offline) 

Explanation    The interface has been placed into the offline state

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_PARENT_ADMIN_DOWN: Interface [chars] is down 
(Parent interface down) 

Explanation    Parent interface is down

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_PEER_CLOSE: Interface [chars] is down(TCP conn. 
closed by peer) 

Explanation    The FCIP peer connected to this interface closed the TCP connection

Recommended Action    This command will provide the peer IP address of this FCIP interface: show interface. Check to see why the peer closed the TCP connection

Error Message      ETHPORT-5-IF_DOWN_PEER_RESET: Interface [chars] is down(TCP conn. 
reset by peer) 

Explanation    TCP connection to the FCIP peer got reset

Recommended Action    The following commands will provide the IP address of the peer and the route used connect to this FCIP peer: show interface, show ip route. Check to see why the peer reset the TCP connection

Error Message      ETHPORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface [chars] is 
down (No operational members) 

Explanation    This is a PortChannel interface and all its members are operationally down

Recommended Action    Enable at least one of the PortChannelsmembers'

Error Message      ETHPORT-5-IF_DOWN_PORT_PROFILE_DEINHERIT_ERR: Interface [chars] is 
down (port-profile de-inherit error) 

Explanation    Interface is down because the existing port-profile on the interface failed to de-inherit properly

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_PORT_PROFILE_INHERIT_ERR: Interface [chars] is 
down (port-profile inherit error) 

Explanation    Interface is down because the associated port-profile failed to inherit properly

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_PORT_PROFILE_NOT_FOUND: Interface [chars] is down 
(port-profile not found) 

Explanation    Interface is down because there is no associated port-profile

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_PORT_VSAN_MISMATCH_ISOLATION: Interface [chars] is 
down (Isolation due to port vsan mismatch) 

Explanation    Isolated due to a mismatch in the configured port VSAN of the local and remote ends

Recommended Action    Configure the port VSAN of the local and remote interfaces to be the same and perform a shutdown'anda'noshutdown''

Error Message      ETHPORT-5-IF_DOWN_RCF_IN_PROGRESS: Interface [chars] is down (RCF in 
progress) 

Explanation    There is an RCF in progress

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_SOFTWARE_FAILURE: Interface [chars] is down (Port 
software failure) 

Explanation    The software servicing the data path on the port has failed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_SRC_MOD_NOT_ONLINE: Interface [chars] is 
down(Tunnel source module not online) 

Explanation    Module that has the tunnel source port of this FCIP interface is not fully online

Recommended Action    The module that has the tunnel src port is coming online. Please use show mod to find module status

Error Message      ETHPORT-5-IF_DOWN_SRC_PORT_NOT_BOUND: Interface [chars] is down 
(Tunnel port src interface unbound) 

Explanation    Tunnel port source interface unbound

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_SRC_PORT_REMOVED: Interface [chars] is down(Tunnel 
src port removed) 

Explanation    Tunnel source port of this FCIP interface has been removed

Recommended Action    The src interface with ip address that matches the ip address of the bound entity is removed. This happens normally due to the module on which the src interface exists is removed

Error Message      ETHPORT-5-IF_DOWN_SUSPENDED_BY_MODE: Interface [chars] is down 
(Suspended due to incompatible mode) 

Explanation    This interface belongs to a PortChannel and operational mode of the interface is different from that of the PortChannel

Recommended Action    Change the mode and the trunking mode of the PortChannel from auto'andchecktoensurethattheremoteendoftheinterfacealsobelongstothesamePortChannel'

Error Message      ETHPORT-5-IF_DOWN_SUSPENDED_BY_SPEED: Interface [chars] is down 
(Suspended due to incompatible speed) 

Explanation    This interface belongs to a PortChannel and operational speedode of the interface is different from that of the PortChannel

Recommended Action    Change the speed of the PortChannel from auto'andchecktoensurethattheremoteendoftheinterfacealsobelongstothesamePortChannel'

Error Message      ETHPORT-5-IF_DOWN_SUSPENDED_BY_WWN: Interface [chars] is down 
(Suspended due to incompatible remote switch WWN) 

Explanation    This interface belongs to a PortChannel and remote switch WWN of the interface is different from that of the PortChannel

Recommended Action    Ensure that this interface is connected to the same remote switch as all the other interfaces in the PortChannel

Error Message      ETHPORT-5-IF_DOWN_SUSPENDED: Interface [chars] is down (Suspended) 

Explanation    This interface belongs to a PortChannel and has been suspended due to an error while bringing it up

Recommended Action    Perform a shutdown'anda'noshutdown'.Ifthishappensagainobtainoutputof'showportinternalinfo/event-history' ontheinterface'

Error Message      ETHPORT-5-IF_DOWN_TCP_KEEP_ALIVE_EXPIRED: Interface [chars] is 
down(TCP conn. closed - Keep alive expired) 

Explanation    TCP session to the FCIP peer got closed due to loss of TCP keep alive

Recommended Action    This may be due to loss of IP connectivity. The following commands will provide the IP address of the peer and the route used connect to this FCIP peer: show interface, show ip route. Please do a trace route to check the connectivity to the peer using command:traceroute ipaddr

Error Message      ETHPORT-5-IF_DOWN_TCP_MAX_RETRANSMIT: Interface [chars] is down(TCP 
conn. closed - retransmit failure) 

Explanation    Interface is down due to maximum retransmission failure

Recommended Action    This may be due to loss of IP connectivity. The following commands will provide the IP address of the peer and the route used connect to this FCIP peer: show interface, show ip route. Please do a trace route to check the connectivity to the peer using command:traceroute ipaddr

Error Message      ETHPORT-5-IF_DOWN_TCP_PERSIST_TIMER_EXPIRED: Interface [chars] is 
down(TCP conn. closed - Persist timer expired) 

Explanation    TCP session to the FCIP peer closed because TCP persist timer expired

Recommended Action    This may be due to loss of IP connectivity. The following commands will provide the IP address of the peer and the route used connect to this FCIP peer: show interface, show ip route. Please do a trace route to check the connectivity to the peer using command:traceroute ipaddr

Error Message      ETHPORT-5-IF_DOWN_UPGRADE_IN_PROGRESS: Interface [chars] is down 
(Linecard upgrade in progress) 

Explanation    Upgrade of the linecard software is in progress

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_VEM_UNLICENSED: Interface [chars] is down (VEM 
unlicensed) 

Explanation    Interface is down because VEM is unlicensed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_VRF_UNUSABLE: Interface [chars] is down (Vrf down) 

Explanation    The vrf for which this interface is a member is removed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_VSAN_MISMATCH_ISOLATION: Interface [chars] is down 
(Isolation due to vsan mismatch) 

Explanation    This is a trunking interface and the VSANs configured do not match with the VSANs configured on the remote end

Recommended Action    Check the VSANs configured on the local end with the remote end

Error Message      ETHPORT-5-IF_DOWN_ZONE_MERGE_FAILURE_ISOLATION: Interface [chars] is 
down (Isolation due to zone merge failure) 

Explanation    Isolated due to a failure during zone merge

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DOWN_ZONE_REMOTE_NO_RESP_ISOLATION: Interface [chars] 
is down (Isolation due to remote zone server not responding) 

Explanation    Isolated due to remote zone server not responding

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_DUPLEX: Interface [chars], operational duplex mode 
changed to [chars] 

Explanation    Operational duplex mode has changed when link came up

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_ERRDIS_RECOVERY: Interface [chars] is being recovered 
from error disabled state (Last Reason:[chars]) 

Explanation    Interface is being recovered from error disabled state

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_HARDWARE: Interface [chars], hardware type changed to 
[chars] 

Explanation    There was a change in the hardware characteristic of an interface, such as a transceiver module plugged in or removed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_L2MP_MODE: Interface [chars], l2mp-mode changed to 
[chars] 

Explanation    The l2mp-mode on the port has changed

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_RX_FLOW_CONTROL: Interface [chars], operational Receive 
Flow Control state changed to [chars] 

Explanation    Operational receive flow control has changed when link came up

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_TRUNK_DOWN: Interface [chars], vlan [chars] down 

Explanation    Interface [chars] is trunking, VLANs [chars] are down

Recommended Action    The following commands will help determine why this VSAN is down on this interface: show interface, show port internal info interface VSAN, show port internal event-history interface vsan

Error Message      ETHPORT-5-IF_TRUNK_UP: Interface [chars], vlan [chars] up 

Explanation    Interface [chars] is trunking, VLANs [chars] are up

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_TX_FLOW_CONTROL: Interface [chars], operational 
Transmit Flow Control state changed to [chars] 

Explanation    Operational transmit flow control has changed when link came up

Recommended Action    No action is required.

Error Message      ETHPORT-5-IF_UP: Interface [chars] is up [chars] 

Explanation    Interface is up in mode specified, if applicable

Recommended Action    No action is required.

Error Message      ETHPORT-5-SPEED: Interface [chars], operational speed changed to 
[chars] 

Explanation    Operational speed has changed when link came up

Recommended Action    No action is required.

Error Message      ETHPORT-5-STORM_CONTROL_ABOVE_THRESHOLD: Traffic in port [chars] 
exceeds the configured threshold [chars] 

Explanation    Traffic on specified port is beyond the configured storm-control threshold, and the excess traffic is being dropped

Recommended Action    Identify source of traffic storm

Error Message      ETHPORT-5-STORM_CONTROL_BELOW_THRESHOLD: Traffic in port [chars] has 
fallen below the configured threshold [chars] 

Explanation    Traffic on specified port has returned to within configured storm-control threshold

Recommended Action    No action is required.

ETH_PORT_CHANNEL Messages

ETH_PORT_CHANNEL-1

Error Message      ETH_PORT_CHANNEL-1-LC_CFG_FAILURE: configuring module [dec] failed 
[[chars]] 

Explanation    Module configuration failed

Recommended Action    Module will be automatically reset

Error Message      ETH_PORT_CHANNEL-1-MALLOC_FAILED: cannot allocate memory (size 
[dec]) 

Explanation    No enough memory

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-1-MAP_PARAM_FAILURE: mapping parameter failed for 
[chars] [[chars]] 

Explanation    Parameter mapping failed

Recommended Action    Specified service is misbehaving; check its status

Error Message      ETH_PORT_CHANNEL-1-MCAST_SEND_FAILURE: failed to send multicast 
[chars]: [chars] 

Explanation    Failed to send a multicast message to all modules, usually because some module went down

Recommended Action    Run show port-channel consistency to check consistency

ETH_PORT_CHANNEL-2

Error Message      ETH_PORT_CHANNEL-2-RESET_MODULE: reset module [dec] for not 
responding or returning error 

Explanation    A module is reset for not responding or returning error

Recommended Action    No action is required.

ETH_PORT_CHANNEL-3

Error Message      ETH_PORT_CHANNEL-3-ADD_REM_MEMBERS_FAILURE: [chars] 

Explanation    Some service(s) failed to add or remove ports to port-channel

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-ALL_DROP_TIMEOUT: Some component(s) (sap:[chars]) 
timed out on dropping notif:[chars] (for:[chars]); Please collect <show system 
internal mts buffers details

Explanation    Some component did not respond to a request in stipulated time.

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-COMPAT_CHECK_FAILURE: [chars] is not compatible 

Explanation    Compatibility check failed when adding ports to port-channel

Recommended Action    Make sure the compatibility parameters are consistent while adding ports to port-channel, or use force option

Error Message      ETH_PORT_CHANNEL-3-GENERAL_ERROR: [chars] 

Explanation    General error

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-3-LACP_ERROR: [chars] [chars] 

Explanation    LACP error

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-3-MSG_SEND_FAILURE: failed to send [chars] to sap 
[dec]: [chars] 

Explanation    Failed to send a message

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-3-NUM_ACTIVE_PORTS_ERROR: Port-channel:[chars] 
active_nports [dec]; No member is active; Please collect <show tech-support 
port-channel/ethpm

Explanation    Port-channel num active ports error

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-PCM_HWCFG_FAIL_ERROR: Port-channel:[chars] 
mbr:[chars] SAP [dec] returned error [chars] for opc [chars]; if lacp port-channel 
please collect <show tech-support lacp all

Explanation    Port-channel hwcfg fail error

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-PCM_INTERNAL_ERROR: Port-channel:[chars] 
mbr:[chars]; if lacp port-channel please collect <show tech-support lacp all

Explanation    Port-channel internal error

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-PCM_PORT_DEL_IN_PC_UP_ERROR: 
Port-channel:[chars] mbr:[chars]; if lacp port-channel please collect <show 
tech-support lacp all

Explanation    Port-channel port del in pc_up. Shut resp recvd before bundle member down

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-PCM_PORT_DOWN_IN_PC_UP_ERROR: 
Port-channel:[chars] mbr:[chars]; if lacp port-channel please collect <show 
tech-support lacp all

Explanation    Port-channel port down in pc_up. No bundle member down

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-PCM_ROLLBACK_INVALID_CHANNEL_ID: Invalid 
channel-id returned for port-channel. Rollback will be perfomed 

Explanation    No action is required.

Recommended Action    Port-channel

Error Message      ETH_PORT_CHANNEL-3-PORT_CHANNEL_NOT_FOUND: [chars] is not found 

Explanation    Cannot find port-channel in its database, which indicates an inconsistency with an external component

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-3-RSP_TIMEOUT: Component [chars] timed out on 
response to opcode:[chars] (for:[chars]) 

Explanation    Some component did not respond to a request in stipulated time.

Recommended Action    None

Error Message      ETH_PORT_CHANNEL-3-TIMEOUT: timed out after [dec] seconds [type 
[chars], state [chars]] 

Explanation    Some operation timed out

Recommended Action    Run show port-channel consistency to check all module connectivity and consistency

ETH_PORT_CHANNEL-4

Error Message      ETH_PORT_CHANNEL-4-PORT_CFG_DELETED: [chars] removed from [chars] 
(different module inserted) 

Explanation    Port is removed from a port-channel because a different module was inserted to the same slot

Recommended Action    You lost some ports from port-channel, check if you want to add ports in the new module to the same port-channel.

Error Message      ETH_PORT_CHANNEL-4-PORT_INDIVIDUAL: port [chars] is operationally 
individual 

Explanation    The port is operating as an individual link even though it is locally or remotely configured to be part of a port channel

Recommended Action    Check the configuration of the port locally and remotely to ensure that it can operate as part of a port channel

Error Message      ETH_PORT_CHANNEL-4-PORT_NOT_FOUND: port [chars] is not part of 
port-channel 

Explanation    Cannot find the port in port-channel database, which indicates an inconsistency with an external component

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-4-RACE_WARN: [chars] 

Explanation    Warning of possible race condition

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-4-UNEXPECTED_RESPONSE: unexpected response [chars] 
from [chars] 

Explanation    Received an unexpected response and discarded

Recommended Action    No action is required.

ETH_PORT_CHANNEL-5

Error Message      ETH_PORT_CHANNEL-5-AUTO_CREATE_FAILURE: [chars] [chars] 

Explanation    Auto create process on the port failed

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-CREATED: [chars] created 

Explanation    A port-channel is created

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-DELETED: [chars] deleted 

Explanation    A port-channel is deleted

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-FOP_CHANGED: [chars]: first operational port 
changed from [chars] to [chars] 

Explanation    The first operational port in a port-channel is changed

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-IF_DOWN_SUSPENDED_BY_MODE: Interface [chars] is 
down (Suspended due to incompatible mode) 

Explanation    Compatibility check failed when adding ports to port-channel

Recommended Action    Make sure the compatibility parameters are consistent between the ports and the port-channel

Error Message      ETH_PORT_CHANNEL-5-IF_DOWN_SUSPENDED_BY_SPEED: Interface [chars] is 
down (Suspended due to incompatible speed) 

Explanation    Operational compatibility check failed on the port in a port-channel

Recommended Action    Make sure the compatibility parameters are consistent between the ports and the port-channel

Error Message      ETH_PORT_CHANNEL-5-MAX_CHANNEL_DISALLOWED: Module failed to come 
online because port channel interface <port-channel number

Explanation    The port-channel number configured on the switch is larger than 128

Recommended Action    Delete the set of port channel interface <port-channel interface

Error Message      ETH_PORT_CHANNEL-5-OPINPROGRESS_TIMEOUT: [chars] operation in 
progress has timed out 

Explanation    Port-channel operation in progress has timed out

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PCM_CHANNEL_GRP_ID_DEPRECATED: channel-group <id

Explanation    Channel-group <id

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PCM_CHANNEL_ID_ASSIGNED: Assigning port channel 
number [dec] for member ports [chars] 

Explanation    No action is required.

Recommended Action    Port-channel

Error Message      ETH_PORT_CHANNEL-5-PCM_MEMBERSHIP_CHANGE_ADD: Interface [chars] is 
added to [chars] 

Explanation    Membership change event occured on the port-channel interface.

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PCM_MEMBERSHIP_CHANGE_DEL: Interface [chars] is 
removed from [chars] 

Explanation    Membership change event occured on the port-channel interface.

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PCM_MEMBER_MODE_CHECK_FAILED: Mode compatibility 
check with existing PC failed for [chars] 

Explanation    No action is required.

Recommended Action    Port-channel

Error Message      ETH_PORT_CHANNEL-5-PCM_ROLLBACK_MAX_PORTS_EXCEEDED: Max ports per 
channel exceeded while trying to create port-channel [dec]. Rollback will be 
performed. 

Explanation    No action is required.

Recommended Action    Port-channel

Error Message      ETH_PORT_CHANNEL-5-PCM_ROLLBACK: Rollback for Port Channel [dec], 
module [dec] 

Explanation    Channel creation failed. Rollback has been performed.

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PCM_SUB_GRP_TYPE_DEPRECATED: sub-group 
<cdp/manual

Explanation    Sub-group <cdp/manual

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_ADDED: [chars] added to [chars] 

Explanation    Ports are added to a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_DOWN: [chars]: [chars] is down 

Explanation    Port goes down in a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_HOT_STANDBY_DOWN: [chars]: hot-standby port 
[chars] is down 

Explanation    Port-channel hot-standby member goes down

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_HOT_STANDBY: [chars]: [chars] goes to 
hot-standby 

Explanation    Port goes to hot-standby in a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_INDIVIDUAL_DOWN: individual port [chars] is 
down 

Explanation    Port-channel member operating in individual mode goes down

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_REMOVED: [chars] removed from [chars] 

Explanation    Ports are removed from a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_SUSPENDED: [chars]: [chars] is suspended 

Explanation    Port is suspended in a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-PORT_UP: [chars]: [chars] is up 

Explanation    Port comes up in a port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-SUBGROUP_ID_CHANGE: Interface [chars] in 
port-channel[dec] subgroup-id changed from [dec] to [dec] 

Explanation    The portssubgroup-idgotchanged'

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-SUBGROUP_ID_PORT_ADDED: Interface [chars] is 
added to port-channel[dec] with subgroup id [dec] 

Explanation    The port is added to port-channel

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-5-SUBGROUP_ID_PORT_REMOVED: Interface [chars] is 
removed from port-channel[dec] with subgroup id [dec] 

Explanation    The port is removed from port-channel

Recommended Action    No action is required.

ETH_PORT_CHANNEL-6

Error Message      ETH_PORT_CHANNEL-6-RESYNC: resyncing [chars] with all modules 

Explanation    Resync modules with sup after an error or switchover

Recommended Action    No action is required.

ETH_PORT_CHANNEL-7

Error Message      ETH_PORT_CHANNEL-7-GSYNC_DONE: global synchronization is done 

Explanation    Port-channel manager finished global synchronization

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-GSYNC_REQ: requesting global synchronization 

Explanation    Port-channel manager requested a global synchronization from active sup

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-START_ACTIVE: started in active mode 

Explanation    Port-channel manager started in active mode

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-START_DEFAULT: started with default configuration 

Explanation    Port-channel manager started with default configuration

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-START_STANDBY: started in standby mode 

Explanation    Port-channel manager started in standby mode

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-START_STATEFUL: started statefully 

Explanation    Port-channel manager started with running configuration

Recommended Action    No action is required.

Error Message      ETH_PORT_CHANNEL-7-START_STATELESS: started statelessly 

Explanation    Port-channel manager started with startup configuration

Recommended Action    No action is required.

EUREKA_USD Messages

EUREKA_USD-3

Error Message      EUREKA_USD-3-MSG1: [chars] 

Explanation    Eureka log message

Recommended Action    No action is required.

EVMC Messages

EVMC-3

Error Message      EVMC-3-MTS_OPERATION_FAILED: [chars]([dec]): [chars] 

Explanation    Internal IPC operation failed in Event Manager Client

Recommended Action    No action is required.

EVMC-4

Error Message      EVMC-4-ACTION_CFG_MONITOR_COLLECT: [chars]([dec]): Action 
configuration disallowed for Monitor Collect Policy 

Explanation    Configuring Policy Action for Monitor Collect Policy isnot allowed and hence, has been rejected

Recommended Action    No action is required.

EVMC-5

Error Message      EVMC-5-AVL_CREATE_FAIL: [chars]([dec]): AVL Tree creation failure 

Explanation    Event Manager could not initialize local policy store

Recommended Action    No action is required.

Error Message      EVMC-5-MALLOC_FAILURE: [chars]([dec]): Memory allocation failure 

Explanation    Event Manager Client process could not allocate memory

Recommended Action    No action is required.

Error Message      EVMC-5-RT_PSS_OP_FAILURE: [chars]([dec]): Failed to [chars]. 
Error:[chars] 

Explanation    Event Manager Client could not access HA store

Recommended Action    No action is required.

EVMS Messages

EVMS-2

Error Message      EVMS-2-EVMS_PSS_DELETE_FAILURE: Delete from PSS failed 

Explanation    Delete from PSS failed

Recommended Action    No action is required.

Error Message      EVMS-2-EVMS_PSS_WRITE_FAILURE: Write to PSS failed 

Explanation    Write to PSS failed

Recommended Action    No action is required.

Error Message      EVMS-2-EVMS_SHOW_POLICY_ALLOC_FAILURE: Insufficient memory: policy 
information shown will be incomplete 

Explanation    Memory allocation failed. so complete requested information is not being shown

Recommended Action    No action is required.

EVMS-4

Error Message      EVMS-4-EVMS_APPLET_NO_ACTION_DEFAULT: WARNING: The default system 
policy actions are being skipped 

Explanation    The default system policy actions are being skipped

Recommended Action    No action is required.

EVMS-6

Error Message      EVMS-6-EVMS_LOGGING_NO_SPACE: logflash full, so deleting first event 
archive file 

Explanation    As the logflash is full, first of the present event archive files is deleted

Recommended Action    No action is required.

EXCEPTIONLOG Messages

EXCEPTIONLOG-SLOT#-2

Error Message      EXCEPTIONLOG-SLOT#-2-LC_EXP_MSG: Linecard exception: [chars] is the 
affected Port bit map. [dec] Additional information - [chars] 

Explanation    LC Exception event.

Recommended Action    No action is required.

FABRICPATH Messages

FABRICPATH-2

Error Message      FABRICPATH-2-FABRICPATH_LINK_BRINGUP_STALLED_STATIC: Link bringup 
stalled due to conflicts 

Explanation    Interface is disabled due to conflicts

Recommended Action    No action is required.

FABRICPATH-4

Error Message      FABRICPATH-4-FABRICPATH_INVALID_FTAG: Invalid ftag [dec] received 

Explanation    Invalid ftag is received from remote

Recommended Action    No action is required.

Error Message      FABRICPATH-4-FABRICPATH_INVALID_SWITCH_ID: Invalid switch-id [dec] 
received 

Explanation    Invalid switch-id is received from remote

Recommended Action    No action is required.

FABRICPATH-6

Error Message      FABRICPATH-6-FABRICPATH_ES_SWID_CONFLICTS: Emulated Switch-id [dec] 
is in conflict with device [chars] 

Explanation    Emulated switch-id collision with other device

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_LINK_BRINGUP_RESOLVE_COLLISION: Resolving 
Collision for switch-id [dec] 

Explanation    Resolving Collision for switch-id

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_LINK_BRINGUP_STALLED_CLEARED: LINK bringup 
cleared for [chars] after collision resolution 

Explanation    Link bringup temporarily suspended due to conflicts

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_LINK_BRINGUP_STALLED: LINK bringup suspended 
for [chars] due to conflicts 

Explanation    Link bringup temporarily suspended due to conflicts

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_NEW_ES_SWITCH_ID: New Emulated switch-id 
[chars] received 

Explanation    New Emulated switch-id received

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_NEW_SWITCH_ID: New switch-id [chars] 
received 

Explanation    New switch-id received

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_SWID_CHANGED: Switch-id [dec] is assigned 
with [chars] state 

Explanation    Local switch-id is changed

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_SWID_CONFLICTS: Switch-id [dec] is in 
conflict with device [chars] 

Explanation    Local switch-id collision with other device

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_SWID_PRI_SEC_CHANGED: Switch-id [dec] is 
changed to [chars] 

Explanation    Local switch-id status changed

Recommended Action    No action is required.

Error Message      FABRICPATH-6-FABRICPATH_SWID_STATE_CHANGED: Switch-id [dec] status 
changed to [chars] 

Explanation    Local switch-id status changed

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-INTERNAL_ERROR: Internal error: [chars] 

Explanation    FCMPLS tunnel process encountered a general error, one that does not fall in any of the categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-IPFC_ERROR: IPFC API, [chars], failed with error [hex] 

Explanation    FCMPLS tunnel invoked IPFC API and received the error code. [chars] describes the API and 0x[hex] specifies the error

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-MTS_ERROR: MTS message transmission failed with error 
[dec] 

Explanation    FCMPLS tunnel process unsuccessfully tried to send a MTS message. MTS errro number is specified in [dec]

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-NS_ERROR: FCNS API, [chars], failed with error [hex] 

Explanation    FCMPLS tunnel invoked FCNS API and received the error code. [chars] describes the API and 0x[hex] specifies the error

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-PM_ERROR: Port Manager API, [chars], failed with error 
[hex] 

Explanation    FCMPLS tunnel invoked Port Manager API and received the error code. [chars] describes the API and 0x[hex] specifies the error

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-PSS_CFG_RESTORE_ERROR: Configuration restoration for 
[chars] failed with error [hex] 

Explanation    FCMPLS tunnel read the saved configuration and encountered an error while rebuilding the runtime configuration. [chars] describes the configuration which the process tried to restore and 0x[hex] is the system error code

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-PSS_ERROR: PSS operation [chars] returned error: [hex] 

Explanation    [chars] specifies the context where the failure occurred and 0x[hex] specifies the error

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-PSS_RTDB_RESTORE_ERROR: Runtime database restoration for 
[chars] failed with error [hex] 

Explanation    FCMPLS tunnel read the saved runtime database and encountered an error while rebuilding the runtime database. [chars] describes the runtime database which the process tried to restore and 0x[hex] is the system error code

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-RIB_ERROR: RIB API, [chars], failed with error [hex] 

Explanation    FCMPLS tunnel invoked RIB API and received the error code. [chars] describes the API and 0x[hex] specifies the error

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-RSVP_PROTO_ERROR: RSVP protocol error: [chars] 

Explanation    RSVP-TE protocol error is encountered. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      FC-TUNNEL-3-UNEXPECTED_MTS_MSG: Unexpected MTS message, opcode 
[dec], is received 

Explanation    FCMPLS tunnel process received unexpected MTS event. MTS opcode is specified in [dec]

Recommended Action    No action is required.

Error Message      FC-TUNNEL-5-MSG_INTERFACE_DOWN: Interface [chars] is down 

Explanation    The logical fc tunnel interface is down. This may be due to a reconfiguration on the fc tunnel, or issues on the underlying physical interface

Recommended Action    If this is not due to a known reconfiguration, you should verify connectivity at the physical port level, and then on then on the fc tunnel interface. Furthermore, verify the physical ports along the fc tunnel path operate in the TE mode

Error Message      FC-TUNNEL-5-MSG_INTERFACE_UP: Interface [chars] is up 

Explanation    The fc interface is up

Recommended Action    No action is required.

FCC_LC Messages

FCC_LC-2

Error Message      FCC_LC-2-ERROR_SENDING_HEART_BEAT: Error sending heart beat [dec] 

Explanation    FCC_LC has error sending heart beat

Recommended Action    No action is required.

Error Message      FCC_LC-2-EXITING: Exiting fcc_lc: [chars] 

Explanation    FCC_LC exiting

Recommended Action    No action is required.

Error Message      FCC_LC-2-HEART_BEAT_NOT_SENT: Heart beat not sent for [dec] millisecs 

Explanation    FCC_LC has not sent heart beat

Recommended Action    No action is required.

Error Message      FCC_LC-2-SHUTDOWN: Process shutting down: [chars] 

Explanation    FCC_LC Process is shutting down

Recommended Action    No action is required.

Error Message      FCC_LC-2-UNABLE_READ_DATA: Unable to read fcc data ([chars]) 

Explanation    FCC is unable to read and process relevant FCC data

Recommended Action    No action is required.

FCC_LC-5

Error Message      FCC_LC-5-BAD_MSG: Received bad message: [chars] 

Explanation    FCC_LC has received a malformed/unrecognized message

Recommended Action    No action is required.

Error Message      FCC_LC-5-DISABLE: FCC_LC has been disabled 

Explanation    FCC_LC has been disabled

Recommended Action    No action is required.

Error Message      FCC_LC-5-ENABLE: FCC_LC has been enabled 

Explanation    FCC_LC has been enabled

Recommended Action    No action is required.

Error Message      FCC_LC-5-STARTING: FCC_LC process started 

Explanation    Process started successfully

Recommended Action    No action is required.

FCC_LC-6

Error Message      FCC_LC-6-PRIO_UPDATE: Updated enable priority to [dec] 

Explanation    FCC_LC is active for packets with priority <= [threshold]

Recommended Action    No action is required.

FCC Messages

FCC-2

Error Message      FCC-2-SHUTDOWN: Process shutting down: [chars] 

Explanation    FCC Process is shutting down

Recommended Action    No action is required.

FCC-5

Error Message      FCC-5-BAD_MSG: Received bad message: [chars] 

Explanation    FCC has received a malformed/unrecognized message

Recommended Action    No action is required.

Error Message      FCC-5-CONGESTION_STATE_CHANGE_NOTIF: Received Congestion State 
Change notification to state: [dec] 

Explanation    FCC has received a Contestion State Change Notification

Recommended Action    No action is required.

Error Message      FCC-5-DISABLE: FCC has been disabled 

Explanation    FCC has been disabled

Recommended Action    No action is required.

Error Message      FCC-5-ENABLE: FCC has been enabled 

Explanation    FCC has been enabled

Recommended Action    No action is required.

Error Message      FCC-5-RATE_LIMIT_END_NOTIF: Received Rate Limit End notification 

Explanation    FCC has received a Rate Limit End Notification

Recommended Action    No action is required.

Error Message      FCC-5-RATE_LIMIT_START_NOTIF: Received Rate Limit Start notification 

Explanation    FCC has received a Rate Limit Start Notification

Recommended Action    No action is required.

Error Message      FCC-5-STARTING: FCC process started 

Explanation    Process started successfully

Recommended Action    No action is required.

FCC-6

Error Message      FCC-6-PRIO_UPDATE: Updated enable priority to [dec] 

Explanation    FCC is active for packets with priority <= [threshold]

Recommended Action    No action is required.

FCDDH Messages

FCDDH-SLOT#-3

Error Message      FCDDH-SLOT#-3-LOG_FCDDH_ERR: Nonrecoverable error - exiting: [chars] 

Explanation    Errors which cause program to exit occurred

Recommended Action    No action is required.

FCDDH-SLOT#-4

Error Message      FCDDH-SLOT#-4-LOG_FCDDH_WARNING: Serious error: [chars] 

Explanation    Serious errors which affect all normal operations occurred

Recommended Action    No action is required.

FCDDH-SLOT#-5

Error Message      FCDDH-SLOT#-5-LOG_FCDDH_DEBUG: Unexpected error: [chars] 

Explanation    Unexpected errors which affect some normal operations occurred

Recommended Action    No action is required.

Error Message      FCDDH-SLOT#-5-LOG_FCDDH_NOTICE: [chars] 

Explanation    Major configuration changes

Recommended Action    No action is required.

FCDD Messages

FCDD-SLOT#-3

Error Message      FCDD-SLOT#-3-LOG_FCDD_ERR: Nonrecoverable error - exiting: [chars] 

Explanation    Errors which cause program to exit occurred

Recommended Action    No action is required.

FCDD-SLOT#-4

Error Message      FCDD-SLOT#-4-LOG_FCDD_WARNING: Warning!: [chars] 

Explanation    Serious errors which affect all normal operations occurred

Recommended Action    No action is required.

FCDD-SLOT#-5

Error Message      FCDD-SLOT#-5-LOG_FCDD_GCONF_FSM: [chars] 

Explanation    Illegal event received in Global Configuration FSM

Recommended Action    No action is required.

Error Message      FCDD-SLOT#-5-LOG_FCDD_NOTICE: [chars] 

Explanation    Major configuration changes

Recommended Action    No action is required.

Error Message      FCDD-SLOT#-5-LOG_FCDD_RESCAN_FSM: [chars] 

Explanation    Illegal event received in Rescan FSM

Recommended Action    No action is required.

Error Message      FCDD-SLOT#-5-LOG_FCDD_TZONE_FSM: [chars] 

Explanation    Illegal event received in Twilight Zone Remover FSM

Recommended Action    No action is required.

Error Message      FCDD-SLOT#-5-LOG_FCDD_VCONF_FSM: [chars] 

Explanation    Illegal event received in VSAN Configuration FSM

Recommended Action    No action is required.

Error Message      FCDD-SLOT#-5-LOG_FCDD_VNO_FSM: [chars] 

Explanation    Illegal event received in VSAN Normal Operation FSM

Recommended Action    No action is required.

FCDD-SLOT#-7

Error Message      FCDD-SLOT#-7-LOG_FCDD_DEBUG: [chars] 

Explanation    Unexpected errors which affect some normal operations occurred

Recommended Action    No action is required.

FCDOMAIN Messages

FCDOMAIN-2

Error Message      FCDOMAIN-2-DOMS_CONFLICT: Conflict detected: ([dec]) domain ID [dec] 
WWN [chars] 

Explanation    Conflict detected ([dec]) domain ID [dec] with WWN [chars].

Recommended Action    Check which switches have the same WWN and change either one; then change eithersdomainID.'

Error Message      FCDOMAIN-2-EPORT_ISOLATED: Isolation of interface [chars] (reason: 
[chars]) 

Explanation    Fcdomain has isolated interface [chars] (reason: [chars].) Perform a show interface. Based on the reason specified, you might have to ensure domains are adequate and unique in the VSAN and perform a disruptive restart [fcdomain restart disruptive vsan <vsan-id

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-FC2BIND_FAILED: Bind to FC2 Service failed 

Explanation    Fcdomain has not been able to contact the FC2 module.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-FC2_INITIALIZATION_FAILED: FC initialization sequence 
failed 

Explanation    The fcdomain has not been able to complete the initialization sequence with the Fibre Channel subsystem. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-FC2_SET_SOCKOPT_DM_SOCK_FAILED: set sockopt to FC2 
Service failed 

Explanation    Fcdomain has not been able to setsockopt to the FC2 module.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-FCID_PERSISTENT_TBL_COMPLETELY_FULL: FCID persistent 
table is completely full 

Explanation    The FCID persistent table is full. Perform [show fcdomain fcid persistent vsan <vsan-id

Recommended Action    Purge stale entries [purge fcdomain fcid] to obtain more free entries OR disable the feature on certain VSANs which are not critical enough [no fcdomain fcid persistent].

Error Message      FCDOMAIN-2-HIGH_PRIORITY_MTSBIND_FAILED: Bind for high priority IPC 
failed 

Explanation    Fcdomain has not been able to contact the Inter Process Communication (IPC) module for its high priority queue.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-INITIALIZATION_FAILED: Initialization sequence failed 

Explanation    The fcdomain has not been able to complete the initialization sequence. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-MTSBIND_FAILED: Bind to IPC failed 

Explanation    Fcdomain has not been able to contact the Inter Process Communication (IPC) module.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-MTSREGISTRATION_FAILED: Registration of opcodes with IPC 
Service failed 

Explanation    Fcdomain has not been able to register its messages with the Inter Process Communication (IPC) module.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-MTS_INITIALIZATION_FAILED: IPC initialization sequence 
failed 

Explanation    The fcdomain has not been able to complete the initialization sequence with the IPC (Inter Process Communication) subsystem. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-MY_NON_VIRTUAL_DOM_CONFLICTS: During VSAN merge detected 
that the local switch has the same domain ID [dec] and WWN [chars] of another 
switch 

Explanation    It has been detected that the local switch has the same domain ID [dec] and WWN [chars] of another switch.

Recommended Action    Check which switches have the same WWN and change either one; then change eithersdomainID.'

Error Message      FCDOMAIN-2-NON_VIRTUAL_DOMS_CONFLICTS: During VSAN merge detected 
conflict between two switches having the same non-virtual domain ID [dec] and the 
same WWN [chars] 

Explanation    It has been detected that two switches have the same non-virtual domain ID [dec] and the same WWN [chars].

Recommended Action    Check which switches have the same WWN and change either one; then change eithersdomainID.'

Error Message      FCDOMAIN-2-PSSBIND_FAILED: Bind to Persistent Storage Service failed 

Explanation    Fcdomain has not been able to contact the Persistent Storage Service (PSS).

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-RDIRJT: Rejected request for domain ID [dec], WWN 
requestor [chars] (reason code [dec]) 

Explanation    An invalid request for domain IDs has been rejected by fcdomain.

Recommended Action    Perform [show fcdomain vsan <vsan-id

Error Message      FCDOMAIN-2-SYSBIND_FAILED: Bind to System Manager service failed 

Explanation    Fcdomain has not been able to contact the System Manager.

Recommended Action    No action is required.

Error Message      FCDOMAIN-2-SYSMGR_INITIALIZATION_FAILED: System Manager 
initialization sequence failed 

Explanation    The fcdomain has not been able to complete the initialization sequence with the System Manager. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    No action is required.

FCDOMAIN-3

Error Message      FCDOMAIN-3-COMMITERRORLOCALINVALIDALLOWEDDOMS: A remote switch 
attempted to locally apply an illicit allowed domains configuration 

Explanation    A remote switch attempted to locally apply an allowed domains configuration that doesntrefusestolocallyapplytheproposedalloweddomains'

Explanation    The remote switch with domain ID [dec] and WWN [chars] refuses to locally apply the proposed allowed domains probably due to incompatibility with its local configured domain or the domain ID list.

Recommended Action    Check the configuration on the remote switch, and make sure that the proposed allowed domains include it. Also, make sure that the the proposed allowed domains include all the domains in the domain ID list.

Error Message      FCDOMAIN-3-MTSOPENTRX_FAILED: IPC failure (opening of a transaction 
failed) 

Explanation    Fcdomain was not able to open a transaction( HA Purposes.)

Recommended Action    No action is required.

Error Message      FCDOMAIN-3-MTSRECV_FAILED: IPC failure (receiving of a message 
failed) 

Explanation    Fcdomain has not been able to receive a message from the Inter Process Communication (IPC) module.

Recommended Action    Please perform fcdomain restart in the affected VSAN (non disruptive.)

Error Message      FCDOMAIN-3-MTSRESP_FAILED: IPC failure replying to a request message 
(error [hex]) 

Explanation    Fcdomain has not been able to reply to a request coming from the Inter Process Communication (IPC) module (error [hex]).

Recommended Action    Please perform fcdomain restart in the affected VSAN (non disruptive).

Error Message      FCDOMAIN-3-MTSSENDREQ_FAILED: IPC failure (sending of a request 
failed) 

Explanation    Fcdomain was not able to send a request using the Inter Process Communication module.

Recommended Action    Please perform [fcdomain restart vsan <vsan-id

Error Message      FCDOMAIN-3-MTSSEND_FAILED: IPC failure (sending of a message (syserr 
[hex], opc [dec], mtsq [dec], sap.node [hex], sap_addr [dec]) failed) 

Explanation    Fcdomain has not been able to send a message to the Message Transactional Service (MTS).

Recommended Action    Please perform [fcdomain restart vsan <vsan-id

Error Message      FCDOMAIN-3-MTS_H_RECV_FAILED: IPC failure (receiving of a message 
failed) 

Explanation    Fcdomain has not been able to receive a message from the Inter Process Communication (IPC) module.

Recommended Action    Please perform fcdomain restart in the affected VSAN (non disruptive.)

Error Message      FCDOMAIN-3-NVRAMFAILURE: NVRAM open failed 

Explanation    Reading the last assigned runtime domain IDs from Non Volatile RAM (NVRAM) failed.

Recommended Action    Fcdomain is able to continue without access to the Non Volatile RAM (NVRAM.)

Error Message      FCDOMAIN-3-PORT_SUSPENDED: Response (Cmd Code [hex]) for SWILS [hex] 
intended for [chars] is received on [chars] 

Explanation    An FC2 response frame (Command Code [hex]) for SWILS [hex] that was intended for interface [chars] has been received on [chars] instead.

Recommended Action    Check the configuration of both interfaces on the local switch and the interfaces on the other side of their corresponding links. In particular, check whether they should all belong to the same port-channel.

Error Message      FCDOMAIN-3-SDWRAPBIND_FAILED: Bind to debug server failed 

Explanation    Fcdomain feature has not been able to contact the debug service. Any problems occurring in the fcdomain feature will not be logged.

Recommended Action    No action is required.

Error Message      FCDOMAIN-3-SDWRAPHISTINIT_FAILED: Initialization of history message 
list failed. 

Explanation    Fcdomain feature has not been able to contact the debug history service. Any problems occurring in the fcdomain feature will not be logged to this debug history.

Recommended Action    No action is required.

Error Message      FCDOMAIN-3-VSAN_MERGE_DETECTED: Merge detected with VSAN [dec] 
(Common Fabric Name [chars]) 

Explanation    The local VSAN and VSAN [dec] have the same principal switch [chars], hence are connected in the same logical fabric.

Recommended Action    No action is required.

FCDOMAIN-4

Error Message      FCDOMAIN-4-DM_ALLOWED_DM_LIST_MOD_ON_SUBORDINATE: Allowed domain 
list for vsan [dec] modified on subordinate switch with fcdomain distribution 
enabled 

Explanation    When distribution is enabled, it is recommended to modify the allow domain list on the principal switch only.

Recommended Action    Abort the current session on the local switch and start a new one on the principal switch.

Error Message      FCDOMAIN-4-FABRICCONFSTARTRCF: Disruptive reconfiguration started 

Explanation    A disruptive reconfiguration (RCF phase) of the VSAN has started. This can happen when two or more fabrics merge disruptively, or when the user manually triggers a diruptive reconfiguration of the VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-4-FC2_CORRUPTED: Received malformed FC2 [chars] frame 

Explanation    Fcdomain received a malformed FC2-SWILS frame.

Recommended Action    No action is required.

Error Message      FCDOMAIN-4-FCID_PERSISTENT_TBL_ALMOST_FULL: FCID persistent table is 
almost full 

Explanation    Fcdomain has 80% or more of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent vsan <vsan-id

Recommended Action    Purge stale entries [purge fcdomain fcid] to obtain more free entries.

FCDOMAIN-5

Error Message      FCDOMAIN-5-DOMAIN_TYPE_IS_PREFERRED: The domain ID type is currently 
configured as preferred in all the existing VSANs 

Explanation    All the currently existing VSANs have the domain ID type configured as preferred. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link.

Recommended Action    Type [fcdomain domain <dom-id

Error Message      FCDOMAIN-5-FCIDP_DISABLED: FCID persistency feature is currently not 
enabled in any of the existing VSANs 

Explanation    All the currently existing VSANs have the FCID persistency feature disabled.

Recommended Action    Type [fcdomain fcid persistent vsan <vsan-id

Error Message      FCDOMAIN-5-FCID_PERSISTENT_TBL_HALF_FULL: FCID persistent table is 
half full 

Explanation    Fcdomain has 50% of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent vsan <vsan-id

Recommended Action    You may want to purge stale entries [purge fcdomain fcid] to obtain more free entries.

Error Message      FCDOMAIN-5-UNKNOWNDOMAININCFSDATAREQUEST: Received CFS Data request 
from unknown domain [dec]. 

Explanation    A CFS Data request from the unknown domain [dec] has been received.

Recommended Action    No action is required.

Error Message      FCDOMAIN-5-UNKNOWNDOMAININCFSLOCKREQUEST: Received CFS Lock request 
from unknown domain [dec]. 

Explanation    A CFS Lock request from the unknown domain [dec] has been received.

Recommended Action    No action is required.

Error Message      FCDOMAIN-5-UNKNOWNDOMAININCFSRELEASEREQUEST: Received CFS Release 
request from unknown domain [dec]. 

Explanation    A CFS Release request from the unknown domain [dec] has been received.

Recommended Action    No action is required.

Error Message      FCDOMAIN-5-UNKNOWNDOMAININUNKNOWNCFSREQUEST: Received CFS request 
from unknown domain [dec]. 

Explanation    A CFS request from the unknown domain [dec] has been received.

Recommended Action    No action is required.

FCDOMAIN-6

Error Message      FCDOMAIN-6-BF_STARTED: BF started by [chars] 

Explanation    Build Fabric has been started in this VSAN

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-CANNOTFREESINGLEFCID: Impossible to free single FCIDs 

Explanation    Impossible to free single FCIDs.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-CLEARLOCKNOTIFICATIONRECEIVED: Implict lock release. 

Explanation    Lock has been implicitly released due to a clear session operation.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-DEVICEALREADYOWNSDIFFERENTFCIDS: The device already owns 
different FCIDs 

Explanation    Requested different FCIDs without any freeing in between.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-DOMAINID_INVALID: Local domain ID invalid 

Explanation    The local domain ID is invalid.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-DOMAINID_VALID: Local domain ID [dec] available 

Explanation    The domain ID [dec] is available.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-DOWNSTREAM_SWITCHED: Downstream interface has been 
fast-switched from [chars] to [chars] 

Explanation    Because of a link failure the downstream interface has been fast-switched from [dec] to [dec].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-EPORT_ALREADY_CREATED: Interface [chars] already created 

Explanation    Interface [chars] already created.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-EPORT_ALREADY_DOWN: Interface [chars] is already down 

Explanation    Interface [chars] already down.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-EPORT_CLEANUP: Interface [chars] received cleanup request 

Explanation    Fcdomain on interface [chars] has received a cleanup request.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-EPORT_CREATED: Creation of interface [chars] 

Explanation    Fcdomain is going to create interface [chars].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-EPORT_DOWN: Interface [chars] is down 

Explanation    Fcdomain is going to remove interface [chars] from its database.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FABRICCONFSTARTBF: Non disruptive reconfiguration started 

Explanation    A non disruptive reconfiguration (BF phase) of the VSAN has started. This can happen when two or more fabrics merge, or when the user manually triggers a non diruptive reconfiguration of the VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FABRICNAME_INVALID: Fabric name not available 

Explanation    Fabric name not available.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FABRICNAME_VALID: Fabric name [chars] available 

Explanation    Fabric name [chars] available.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCIDALREADYFREE: FCIDs already free 

Explanation    FCIDs already free.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCIDNOTSTORED: FCIDs not stored 

Explanation    FCIDs not stored.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCIDP_ENABLED_DOM_TYPE_PREFERRED: FCID persistency is 
enabled, but the domain ID type is configured as preferred 

Explanation    The FCID persistency feature is enabled, but the domain ID type is configured as preferred. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link. Should the domain ID change, all the FCIDs associated with it would be invalidated.

Recommended Action    Type [fcdomain domain <dom-id

Error Message      FCDOMAIN-6-FCIDS_ASSIGNED: Assigned a sequence of 256 contiguous 
FCIDs starting from FCID [hex]:[hex]:[hex] 

Explanation    Assigned a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCIDS_FREED: Freed a sequence of 256 contiguous FCIDs 
starting from FCID [hex]:[hex]:[hex] 

Explanation    Freed a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCID_ASSIGNED: Assigned single FCID [hex]:[hex]:[hex] 

Explanation    Assigned single FCID [hex]:[hex]:[hex].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-FCID_FREED: Freed single FCID [hex]:[hex]:[hex] 

Explanation    Freed single FCID [hex]:[hex]:[hex].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-INCORRECTDOMAINRANGE: Requested FCIDs with domain field 
not in expected range 

Explanation    Requested FCIDs with domain field not in expected range.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-INCORRECTDOMAIN: Requested FCIDs with domain field 
different from local domain 

Explanation    Requested FCIDs with domain field different from local domain.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-INVALIDARG: Requested FCID of type 00.00.YY, but 
specifying an entire area 

Explanation    Requested FCID of type 00.00.YY, but specifying an entire area.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-MY_SAME_WWN_DIFFERENT_DOMS_CONFLICTS: During VSAN merge 
detected local WWN [chars] is already in use by another switch (the two switches 
have different domain IDs: [dec] (local) and [dec]) 

Explanation    It has been detected that the local switch has the same WWN [chars] of another switch, and that they have different domain IDs: [dec] (local) and [dec].

Recommended Action    Check which switches have the same WWN and change either one.

Error Message      FCDOMAIN-6-NODOMAIN: Local domain not available 

Explanation    The local domain is not available yet.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-NOFREEFCID: No free FCIDs 

Explanation    No free FCIDs.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-NOTOWNER: Feature [dec] cannot free FCID 
[dec]:[dec]:[dec] (feature [dec] is the actual owner) 

Explanation    Feature UUID [dec] cannot free FCID [dec]:[dec]:[dec] because it is not its owner (UUID actual owner is [dec]).

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-OTHER_SIDE_VIRTUAL_IVR_DOMS_OVERLAPPING: During VSAN 
merge detected overlap with virtual IVR domain ID [dec] from across the link 

Explanation    It has been detected an overlap with the virtual IVR domain ID [dec] from across the link during an attempt to merge the local VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-PSWSSTARTED: Principal Switch Selection started 

Explanation    Fcdomain started a principal switch selection phase to elect a principal switch in this VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-RCF_STARTED: RCF started by [chars] 

Explanation    Reconfigure Fabric has been started in this VSAN

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-REQSINGLEFCIDWITHINRESERVEDRANGE: Requested single FCIDs 
in area [dec] within the reserved range 

Explanation    Requested single FCIDs in area [dec] within the reserved range.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-REQUESTEDFCIDNOTFREE: Requested FCIDs not free 

Explanation    Requested FCIDs not free.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-REQUESTEDFCIDRESERVED: Requested reserved FCIDs 

Explanation    Requested reserved FCIDs.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-REQUESTEDRESERVEDFCIDMISMATCH: Requested persistent 
FCIDs, but there is a mismatch 

Explanation    Requested persistent FCIDs, but there is a mismatch.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-SAME_WWNS_DIFFERENT_DOMS_CONFLICTS: During VSAN merge 
detected two switches with same WWN [chars] and different non-virtual domain IDs 
[dec] and [dec] 

Explanation    It has been detected that two switches have the same WWN [chars], but different non-virtual domain IDs: [dec] and [dec].

Recommended Action    Check which switches have the same WWN and change either one.

Error Message      FCDOMAIN-6-TIMER_UNKNOWN: fcdomain has received a notification for 
an unknown timer expiration 

Explanation    A timer unknown to fcdomain has expired.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-UPSTREAM_SWITCHED: Upstream interface has been 
fast-switched from [chars] to [chars] 

Explanation    Because of a link failure the upstream interface has been fast-switched from [dec] to [dec].

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-UUIDNOSPACEFOUND: No available space to store the identity 
of the requestor the FCIDs 

Explanation    No available space to store the identity of the requestor the FCIDs.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-UUIDNOTFOUND: Universal Unique ID (UUID) not found 

Explanation    Universal Unique ID (UUID) not found.

Recommended Action    No action is required.

Error Message      FCDOMAIN-6-VIRTUAL_IVR_DOMS_OVERLAPPING: During VSAN merge detected 
overlap with local virtual IVR domain ID [dec] 

Explanation    It has been detected an overlap with the local virtual IVR domain ID [dec] during an attempt to merge the local VSAN.

Recommended Action    No action is required.

FCDOMAIN-7

Error Message      FCDOMAIN-7-EPORT_ALREADY_ISOLATED: Interface [chars] is already 
isolated or down 

Explanation    Fcdomain was going to isolate interface [chars], but the interface is already isolated.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FABRICCONFCOMPLETEDBF: Non disruptive reconfiguration 
completed 

Explanation    A non disruptive reconfiguration (BF phase) completed. This can happen when two or more fabrics merged, or when the user manually triggered a non diruptive reconfiguration of the VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FABRICCONFCOMPLETEDRCF: Disruptive reconfiguration 
completed 

Explanation    A disruptive reconfiguration (RCF phase) of the VSAN has completed. This can happen when two or more fabrics merged disruptively, or when the user manually triggered a diruptive reconfiguration of the VSAN.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FC2_RETRY: Retransmission of FC2 frame on interface 
[chars] (Cmd Code: [hex]) 

Explanation    Fcdomain is retrying an FC2 frame on interface [chars] due to loss/no response. The Command Code of the frame is [hex].

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FCID_IN_USE_PURGING_FOR_FICON_MGR: FICON needs to purge 
the persistent FCID table, but at least one FCID is still in use, preventing this 
purge from completely remove all entries belonging to the VSAN. 

Explanation    There may be a problem in the sequence that shuts down all interfaces before fcdomain receives a request from FICON Manager to purge the persistent FCID table.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FSM_FAILED: FSM transition failed on interface [chars] 
(current state [chars]) 

Explanation    Fcdomain state machine generated an invalid event on interface [chars], for which no proper action was defined (current state [chars].)

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-FSM_FORBIDDEN_TRANSITION: fcdomain state machine has hit 
a forbidden transition 

Explanation    Fcdomain state machine has tried to execute a forbidden transition.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-INTERFACERDY: Interface [chars] ready 

Explanation    Interface [chars] is ready.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-PREACTIONTYPE_UNKNOWN: fcdomain state machine has hit an 
unknown pre-action type 

Explanation    An undefined pre-action type has been used.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-PSWSCOMPLETED: Principal Switch Selection completed 

Explanation    A Principal Switch Selection (PSwS phase) completed.

Recommended Action    No action is required.

Error Message      FCDOMAIN-7-RDIACC: Assigned domain ID [dec], WWN of requestor [chars] 
(requested domain ID [dec]) 

Explanation    Domain ID [dec] has been received by VSAN with WWN [chars] (requested domain ID was [dec].)

Recommended Action    No action is required.

FCD Messages

FCD-7

Error Message      FCD-7-SB3_ABTS_EXCHANGE: sb3 aborted exchange [hex] from vsan:[dec] 
ch:[hex] chi:[hex] ccw:[hex] token:[hex] cmd:[hex] reason:[chars] 
state:[chars]:[dec] 

Explanation    SB3 aborted exchange due to reason given. Aborts are caused by either the channel or control unit detecting a device protocol error. Recovery actions are performed to restore communication. In certain circumstances aborts occur in normal operations.

Recommended Action    No action is required if communication with CUP device is still operational.

Error Message      FCD-7-SB3_UCS_PER_FILE_FN: VSAN:[dec] Unit Check for perform file 
function, reason: [chars] 

Explanation    SB3 failed perform file function. Failure is caused by error in the file main frame sent to director.

Recommended Action    No action is required if communication with CUP device is still operational.

FCFWD Messages

FCFWD-3

Error Message      FCFWD-3-ERROR: [chars] 

Explanation    Fcfwd encountered an error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FCFWD-4

Error Message      FCFWD-4-WARNING: [chars] 

Explanation    Fcfwd is generating a relevant notification

Recommended Action    No action is required.

FCFWD-6

Error Message      FCFWD-6-INFO: [chars] 

Explanation    An fcfwd event occurred

Recommended Action    No action is required.

FCNS Messages

FCNS-2

Error Message      FCNS-2-DB_FULL: the database; max entries [dec] exceeded 

Explanation    Name server database is full. The max number of entries, [dec], of ports is already present in the database

Recommended Action    No action is required.

Error Message      FCNS-2-INIT_FAILURE: : [chars] 

Explanation    Fcns initialisation has failed due to [chars].

Recommended Action    No action is required.

Error Message      FCNS-2-NO_RESPONSE: for query [chars] from domain [dec] 

Explanation    No response for query [chars] from domain [dec].

Recommended Action    No action is required.

Error Message      FCNS-2-PSS_VERSION_MISMATCH: : for [chars] 

Explanation    Version mismatch for pss of type [chars].

Recommended Action    No action is required.

Error Message      FCNS-2-RELOAD_FAILURE: : [chars] 

Explanation    Failed to reload information from PSS: [chars].

Recommended Action    No action is required.

FCNS-3

Error Message      FCNS-3-BAD_FRAME: : [chars] 

Explanation    Received a bad frame from the network: [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-CFG_FAILURE: : [chars] 

Explanation    A failure related to fcns configuration: [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-CHUNK_FAILURE: : [chars] 

Explanation    Chunk memory failure: [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-DB_FAILURE: : [chars] 

Explanation    A failure occured in fcns database: [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-MALLOC_FAILURE: : [chars] 

Explanation    Malloc failed: [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-MTS_FAILURE: : [chars] [chars] 

Explanation    Failure occured trying to do an MTS operation: [chars] [chars].

Recommended Action    No action is required.

Error Message      FCNS-3-PSS_FAILURE: : [chars] 

Explanation    Pss failure: [chars].

Recommended Action    No action is required.

FCNS-4

Error Message      FCNS-4-QUERY_NO_RESPONSE: for query [chars] from domain [dec] 

Explanation    No response for query [chars] from domain [dec].

Recommended Action    No action is required.

FCNS-6

Error Message      FCNS-6-DB_INFO: : [chars] [hex] 

Explanation    Database modification:[chars] for entry [hex].

Recommended Action    No action is required.

Error Message      FCNS-6-STATUS_INFO: : [chars] 

Explanation    A change in fcns status: [chars].

Recommended Action    No action is required.

FCOE_MGR Messages

FCOE_MGR-2

Error Message      FCOE_MGR-2-FCOE_MGR_PSS_RESTORE_FAILED: FCoE Manager PSS Restore 
operation failed, error: [chars] 

Explanation    FCoE Manager PSS Restore operation failed

Recommended Action    No action is required.

FCOE_MGR-5

Error Message      FCOE_MGR-5-FCOE_MGR_DISABLED: FCOE_MGR Disabled 

Explanation    FCOE_MGR Service Disabled

Recommended Action    No action is required.

Error Message      FCOE_MGR-5-FCOE_MGR_ENABLED: FCOE_MGR Enabled 

Explanation    FCOE_MGR Service Enabled

Recommended Action    No action is required.

Error Message      FCOE_MGR-5-FCOE_MGR_INFO: [chars] 

Explanation    FCoE Manager general info

Recommended Action    No action is required.

Error Message      FCOE_MGR-5-FCOE_MGR_SOLICITATION_FROM_SAME_MAC: FCoE Manager 
received Mulicast Solication from same MAC: [chars] 

Explanation    FCoE Manager received Mulicast Solication from same MAC

Recommended Action    No action is required.

Error Message      FCOE_MGR-5-FCOE_MGR_VE_DUPLICATE_PEER_MAC: FCoE Manager has already 
received unicast advertisement from MAC [chars] on a different VE link. Bringing 
down this link 

Explanation    FCoE Manager has already received unicast advertisement from same MAC on a different VE link

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-DBG_INIT_FAILED: Debug Infrastructure Initialization 
failed ( [chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FC2_E_INIT_FAILED: Fibre-Channel Initialization of an 
E_Port failed ( [chars] ) 

Explanation    FC-SP Manager has been unable to initialize with the FC-2 E-Port infrastructure.

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an 
F_Port failed ( [chars] ) 

Explanation    FC-SP Manager has been unable to initialize with the FC-2 F-Port infrastructure.

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FC2_UNKNOWN_FRM_RECD_CRIT: Received an unexpected/unknown 
FC-2 frame on [chars] 

Explanation    .

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FCSP_AUTHENT_FAILURE: FC-SP Authentication failure on 
Port [chars] (FC-SP Failure Reason: [chars] [chars]) 

Explanation    Fibre-Channel Authentication failure on Port [chars].(Reason Code [chars] Detail [chars]). Please check password configurations and ensure appropriate security modes on this port as well as peer port

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FCSP_ESP_MISMATCH: ESP parameters mismatch failure on 
Port [chars] (reason:[chars]) 

Explanation    Fibre-Channel ESP parameters mismatch with the peer on Port [chars].(Reason: [chars]). Please check ESP configurations on both side of the link and ensure appropriate ESP mode on this port as well as peer port

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-FSMU_INIT_FAILED: State Machine Infrastructure 
Initialization failed ( [chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-IPC_INIT_FAILED: IPC (Inter Process Communication) 
Initialization failed ( [chars] ) 

Explanation    FC-SP Manager has been unable to initialize with the IPC infrastructure.

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service 
exiting 

Explanation    License of [chars] is unavailable. Service will exit now

Recommended Action    Please install the license file to continue using the feature.

Error Message      FCSP-MGR-2-MEM_FAILED: Memory operations failed File: [chars] Line 
[dec] for size [hex] bytes 

Explanation    .

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-POST_INIT_FAILED: Post-Initialization failed ( [chars] ) 

Explanation    .

Recommended Action    No action is required.

Error Message      FCSP-MGR-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed 
( [chars] ) 

Explanation    .

Recommended Action    No action is required.

FCS Messages

FCS-2

Error Message      FCS-2-ALLOC_FAILED: Memory allocation failed for size:[dec] 

Explanation    Memory allocation failed for size [dec]

Recommended Action    Restart the process

Error Message      FCS-2-CHUNK_ALLOC_FAILED: Chunk memory allocation failed for [chars] 
chunk 

Explanation    Chunk memory allocation failed. [chars] indicates the chunk name

Recommended Action    Restart the process

Error Message      FCS-2-NO_RESPONSE: Retried maximum number of times for [chars] to 
domain [dec] in VSAN [dec] 

Explanation    Maximum number of retires completed for [chars] form domain [dec] in VSAN [dec].

Recommended Action    No action is required.

Error Message      FCS-2-PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], 
expected version [dec].[dec].[dec] 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-2-RANDNUM_FAIL: [chars] 

Explanation    There was a critical error during random number generation. [chars] indicates details of the error

Recommended Action    No action is required.

FCS-3

Error Message      FCS-3-DB_ERR: [chars] 

Explanation    An error occurred during an FCS database operation. [chars] indicates the reason for the error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-INIT_FAIL: [chars] 

Explanation    An error happened during FCS Initialization. [chars] indicates the reason for failure

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-MTS_API_ERR: [chars] : [chars] 

Explanation    An error occurred in send or receive of an MTS message. [chars] indicates the error that occurred and [chars] indicates the error number

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-MTS_ERR: [chars] 

Explanation    An error occurred in processing of an MTS message. [chars] indicates the error that occurred

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-NO_MTS_RESP: [chars] 

Explanation    There was no response to an MTS request. [chars] indicates details of the MTS message

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-NO_REMOTE_RESP: No response for request [chars] from domain 
[dec] in VSAN [dec] 

Explanation    There was no response to an FC2 request. [chars] indicates FCS request [dec] indicates the remote domain and [dec] the VSAN ID

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-OTHER_ERR: [chars] 

Explanation    An FCS generic error occurred. [chars] indicates the description of the error

Recommended Action    No action is required.

Error Message      FCS-3-PSS_ERR: [chars] 

Explanation    An error occurred during an FCS PSS operation. [chars] indicates the PSS operation that caused the error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FCS-3-SOCK_ERR: sd: [dec], [chars] 

Explanation    An FC-2 Socket error occurred on socket-ID [dec]. [chars] indicates the reason for failure

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FCS-5

Error Message      FCS-5-API_FAIL: [chars]: [chars] 

Explanation    An API called by FCS failed. [chars] indicates the API name failed and [chars] the reason for failure

Recommended Action    If this message is seen during a cold boot, it means that the queried module came up after FCS and this case can be ignored

Error Message      FCS-5-DB_NOTICE: [chars] 

Explanation    An error occurred during an FCS database operation. [chars] indicates the reason for the error

Recommended Action    No action is required.

FCS-6

Error Message      FCS-6-BAD_CT_FRAME: Invalid FCS frame: [chars] received from [hex] 

Explanation    An invalid FCS FC-CT frame with [chars] received from FC-ID [hex].

Recommended Action    No action is required.

Error Message      FCS-6-INFORMATION: [chars] 

Explanation    An event happend that affects FCS. [chars] indicates the event

Recommended Action    No action is required.

Error Message      FCS-6-REXMIT_PKT: Retransmitting request [chars] to domain [dec] in 
VSAN [dec] 

Explanation    There was a retransmission of an FC2 request. [chars] indicates FCS request [dec] indicates the remote domain and [dec] the VSAN ID

Recommended Action    No action is required.

FDMI Messages

FDMI-2

Error Message      FDMI-2-FDMI_INIT_FAILED: FDMI initialization failed : [chars] 

Explanation    Fdmi process encountered error while starting

Recommended Action    No action is required.

Error Message      FDMI-2-MTS_ERROR: MTS message transmission failed with error [dec] 

Explanation    Fdmi process unsuccessfully tried to send a MTS message. MTS errro number is specified in [dec]

Recommended Action    No action is required.

Error Message      FDMI-2-PSS_CFG_RESTORE_ERROR: Configuration restoration for [chars] 
failed with error [hex] for key type [dec] 

Explanation    Fdmi read the saved configuration and encountered an error while rebuilding the runtime configuration. [chars] describes the configuration which the process tried to restore and 0x[hex] is the system err code

Recommended Action    No action is required.

Error Message      FDMI-2-PSS_RTDB_RESTORE_ERROR: Runtime database restoration for 
[chars] failed with error [hex] 

Explanation    Fdmi read the saved runtime database and encountered an error while rebuilding the runtime database. [chars] describes the runtime database which the process tried to restore and 0x[hex] is the system err code

Recommended Action    No action is required.

FDMI-3

Error Message      FDMI-3-BAD_FRAME: Malformed frame received: [chars] 

Explanation    Fdmi process received malformed frame. [chars] describes the malformation

Recommended Action    No action is required.

Error Message      FDMI-3-BAD_RESPONSE: response with command code: [hex] 

Explanation    Fdmi process received bad payload in response

Recommended Action    No action is required.

Error Message      FDMI-3-INTERNAL_ERROR: Internal err: [chars] 

Explanation    Fdmi process encountered a general error, one that does not fall in any of the categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message      FDMI-3-MTS_API_ERROR: API, [chars] returned [hex] 

Explanation    Fdmi invoked API [chars], received the error code specified in 0x[hex]

Recommended Action    No action is required.

Error Message      FDMI-3-MTS_FORMAT_ERROR: Unknown MTS message format in opcode [dec] 
from module [chars] 

Explanation    Fdmi received message from module [chars] which contains unknown message format. MTS opcode is specified in [dec]

Recommended Action    No action is required.

Error Message      FDMI-3-NO_RESPONSE: No response from switch whose domain id is [dec] 

Explanation    Fdmi process sents a inter-switch packets to switches and has not received the response

Recommended Action    No action is required.

Error Message      FDMI-3-PSS_ERROR: PSS operation [chars] returned err: [hex] 

Explanation    [chars] specifies the context where the failure occured and 0x[hex] specifies the err

Recommended Action    No action is required.

Error Message      FDMI-3-UNEXPECTED_MTS_MSG: Unexpected MTS message, opcode [dec], is 
received 

Explanation    Fdmi process received unexpected MTS event. MTS opcode is specified in [dec]

Recommended Action    No action is required.

FDMI-4

Error Message      FDMI-4-SW_REJ_RESPONSE: Reject response [chars] from switch whose 
domain id is [dec] 

Explanation    Fdmi process sents a inter-switch packets to switches and has received the reject response with reason code in [chars]

Recommended Action    No action is required.

FDMI-6

Error Message      FDMI-6-DEBUG_INFO: [chars] 

Explanation    Fdmi process debug info

Recommended Action    No action is required.

Error Message      FEATURE-MGR-2-FM_AUTOCKPT_FAILED: AutoCheckpoint [chars] failed to 
be created for reason: [chars] ([hex]) 

Explanation    AutoCheckpoint with the given name has been created successfully

Recommended Action    No action is required.

Error Message      FEATURE-MGR-2-FM_FEATURE_LICENSE_ERROR: the license operation for 
feature failed [hex] [chars] 

Explanation    License operation was not successful, check license validity for the feature

Recommended Action    Please contact FM team

Error Message      FEATURE-MGR-2-FM_FEATURE_OP_TIMEOUT_ERROR: feature [chars] operation 
failed on response timeout from service: [chars] with uuid ([hex]) 

Explanation    The error seen at FM and service communication

Recommended Action    Please contact service owner with given uuid and FM team

Error Message      FEATURE-MGR-2-FM_FSET_ADD_CONFCHECK_ERROR: failed to add confcheck 
[hex] ([chars]) at installing feature-set [chars] 

Explanation    Failed to add confcheck at enabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_CFG_ALLOW_ERROR: Potential vdc_mgr issue: the 
allow request failed [hex] ([chars]) 

Explanation    Vdc_mgr failed to response the allow request

Recommended Action    Please contact FM/vdc_mgr team

Error Message      FEATURE-MGR-2-FM_FSET_CKPT_ERROR: Checkpoint issue: failed on 
checkpoint with error [hex] ([chars]) at feature-set [chars] 

Explanation    Checkpoint did not response

Recommended Action    Please contact FM/vdc_mgr and rollback team

Error Message      FEATURE-MGR-2-FM_FSET_DISABLE_ERROR: Potential sysmgr issue: disable 
feature-set [chars] on sup failed with error [hex] ([chars]) 

Explanation    Some issues while disabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_DISABLE_FEATURES_ERROR: features failed to 
disable at feature-set [chars] with error [hex] ([chars]) 

Explanation    Failed to disable feature at disabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_DISABLE_FEATURES_TIMEOUT: Potential [chars] 
issue: feature [chars] did not complete its disabling 

Explanation    Failed to disable feature at disabling feature-set

Recommended Action    Please contact FM/sysmgr team and the feature owner

Error Message      FEATURE-MGR-2-FM_FSET_INSTALL_ERROR: install feature-set [chars] 
returns error 0X[hex] ([chars]) 

Explanation    Somes issues during install feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_LCS_DISABLE_ERROR: Potential sysmgr issue: 
disable feature-set [chars] failed on module [dec] with error [hex] ([chars]) 

Explanation    Some issues on the lc while disabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_LCS_ENABLE_ERROR: enabling feature-set [chars] 
on module [dec] returns error 0X[hex] ([chars]) 

Explanation    Somes issue on the lc while enabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_PRESEQ_REJECT: It rejects pre-sequence due to 
a service with sap [dec]: [chars] 

Explanation    The message seen when an application rejects feature-set disable request

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_SUP_ENABLE_ERROR: enabling feature-set [chars] 
on sup returns error 0X[hex] ([chars]) 

Explanation    Some issues during enabling feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_UNGRACEFUL_DISABLE_ERROR: Potential sysmgr 
issue: ungraceful disable feature-set [chars] failed with error [hex] ([chars]) 

Explanation    Some issues while ungraceful disable feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_UNGRACEFUL_UNINSTALL_ERROR: Potential sysmgr 
issue: ungraceful uninstall feature-set [chars] failed with error [hex] ([chars]) 

Explanation    Some issues while ungraceful uninstall feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_UNINSTALL_ERROR: Potential sysmgr issue: 
uninstall feature-set [chars] failed with error [hex] ([chars]) 

Explanation    Some issues while uninstall feature-set

Recommended Action    Please contact FM/sysmgr team

Error Message      FEATURE-MGR-2-FM_FSET_VMM_OP_ERROR: [chars] 

Explanation    The error seen at FM and VMM interaction

Recommended Action    Please contact FM/VMM team

Error Message      FEATURE-MGR-2-MODULE_FM_DONE: feature manager completed 

Explanation    Feature manager completed

Recommended Action    No action is required.

Error Message      FEATURE-MGR-2-MODULE_FM_STARTED: feature manager started 

Explanation    Feature manager started

Recommended Action    No action is required.

Error Message      FEATURE-MGR-6-FM_AUTOCKPT_IN_PROGRESS: AutoCheckpoint 
[chars]screationinprogress...'

Explanation    AutoCheckpoint creation has been requested and it should be in progress

Recommended Action    No action is required.

Error Message      FEATURE-MGR-6-FM_AUTOCKPT_SUCCEEDED: AutoCheckpoint [chars] created 
successfully 

Explanation    AutoCheckpoint with the given name has been created successfully

Recommended Action    No action is required.

Error Message      FEATURE-MGR-6-FM_FCOE_AUTOINSTALL_ON_NOT_ISOLA: auto-install 
feature-set fcoe on non-isola 

Explanation    Auto-install feature-set fcoe could be done on isola only

Recommended Action    Please contact FM team

Error Message      FEATURE-MGR-6-FM_FSET_ENABLED_AT_UNINSTALL: Uninstall aborted 
because feature set is still enabled in vdc [dec] 

Explanation    Feature set is in enabled state

Recommended Action    No action is required.

FEX Messages

FEX-2

Error Message      FEX-2-FEX_NOT_ONLINE_SUP_ISSU: FEX [dec] did not come online after 
SUP ISSU 

Explanation    FEX did not come online after sup ISSU

Recommended Action    No action is required.

Error Message      FEX-2-FEX_OFFLINE: FEX [dec] has gone OFFLINE 

Explanation    FEX has gone OFFLINE

Recommended Action    No action is required.

Error Message      FEX-2-FEX_ONLINE: FEX [dec] has come ONLINE 

Explanation    FEX has come ONLINE

Recommended Action    No action is required.

Error Message      FEX-2-FEX_PORT_STATUS_CRIT: Uplink-ID [dec] of Fex [dec] that is 
connected with [chars] changed its status from [chars] to [chars] 

Explanation    Fex [decimal-digit] changed port status

Recommended Action    No action is required.

Error Message      FEX-2-NOHMS_ENV_FEX_OFFLINE: [chars] 

Explanation    Fex off-line

Recommended Action    Show inventory

Error Message      FEX-2-NOHMS_ENV_FEX_ONLINE: [chars] 

Explanation    Fex on-line

Recommended Action    Show inventory

FEX-5

Error Message      FEX-5-FEX_DISABLED: FEX Disabled 

Explanation    FEX Service Disabled

Recommended Action    No action is required.

Error Message      FEX-5-FEX_ENABLED: FEX Enabled 

Explanation    FEX Service Enabled

Recommended Action    No action is required.

Error Message      FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID [dec] of Fex [dec] that is 
connected with [chars] changed its status from [chars] to [chars] 

Explanation    Fex [decimal-digit] changed port status

Recommended Action    No action is required.

Error Message      FEX-5-PINNING_CHANGED: Fex [dec] pinning information is changed 

Explanation    Fex pinning information changed

Recommended Action    No action is required.

Error Message      FEX-5-SATMGR_DISABLE_FAILED: Disabling of feature FEX failed. Please 
remove FEX related configs from interfaces 

Explanation    Disabling of FEX feature failed

Recommended Action    No action is required.

FICON Messages

FICON-2

Error Message      FICON-2-E_DUPLICATE_PN_BRINGUP_FAIL: [chars] 

Explanation    This port has the same port number assigned to other port in the same FICON VSAN. No more than one port with duplicate port number can be up in each FICON VSAN

Recommended Action    Avoid duplicate number assignment in each FICON VSAN

Error Message      FICON-2-E_PN_PA_NOT_IN_BOUND: [chars] 

Explanation    Port number or port address in startup-configure is out of bound.

Recommended Action    Change ficon port number assign configuration and save to startup-configure.

Error Message      FICON-2-E_SAVE_FILE: [chars] 

Explanation    Failed to save file. Possibly due to asymmetric pdcm matrix. Look for retval for actual reason.

Recommended Action    Configure port prohibits in symmetrically.

Error Message      FICON-2-SHUTDOWN: FICON Manager process shutting down: [chars] 

Explanation    FICON Manager shutting down

Recommended Action    This is a severe error. Provide the reason given in the message

FICON-3

Error Message      FICON-3-E_ASSIGN_BINDING_PN_FAIL: [chars] 

Explanation    Port number has fcip or port channle binding can not be removed nor changed.

Recommended Action    Remove port number binding of the logical interface first.

Error Message      FICON-3-E_ASSIGN_INVALID_PN_PARAM: [chars] 

Explanation    Invalid port number parameters in command.

Recommended Action    Check port numbers in the command.

Error Message      FICON-3-E_ASSIGN_OVERLAP_PN_FAIL: [chars] 

Explanation    Port number assigned to physical and logical can not overlap.

Recommended Action    Check port numbers in the command.

Error Message      FICON-3-E_ASSIGN_PN_NOT_DOWN_FAIL: [chars] 

Explanation    Only port number assigned to a port in down state can be removed or changed.

Recommended Action    Bring down the port first.

Error Message      FICON-3-E_ASSIGN_PROHIBIT_PN_FAIL: [chars] 

Explanation    Logical port address can not be prohibited.

Recommended Action    Check port numbers in the command.

Error Message      FICON-3-E_DUPLICATE_PN_ASSIGN_WARNING: [chars] 

Explanation    This port has the same port number assigned to other port in the same FICON VSAN. No more than one port should have the same port number in each FICON VSAN

Recommended Action    Avoid duplicate number assignment in each FICON VSAN

Error Message      FICON-3-E_INVALID_PA_BRINGUP_FAIL: [chars] 

Explanation    This port either has an invalid port address assigned or has no port address assigned.

Recommended Action    Assign a valid ficon port number to the port.

Error Message      FICON-3-E_PORT_PROHIBIT_BRINGUP_FAIL: [chars] 

Explanation    This port has been prohibited. Prohibiting E or TE ports is not allowed. This port can not be configured in E mode or TE mode until the prohibit mask configuration is changed

Recommended Action    Correct the prohibit mask (PDCM) for this port if you wish to bring it up as an E or TE port in a FICON VSAN

Error Message      FICON-3-E_UNASSIGN_NO_PN_FAIL: [chars] 

Explanation    Only port number already assigned can be removed.

Recommended Action    Check port numbers in the command.

Error Message      FICON-3-PDCM_CHANGE_REJ_E_PORT: [chars] 

Explanation    The FICON Prohibit Dynamic Connectivity Mask(PDCM) change rejected because an E or TE port is being prohibited. Prohibiting an E or TE port in not allowed

Recommended Action    Correct the prohibit mask (PDCM) for this port if you wish to bring the port up as an E or TE port in a FICON VSAN

FICON-5

Error Message      FICON-5-STARTING: FICON Manager process starting 

Explanation    FICON Manager process is being started

Recommended Action    No action is required.

FICON-6

Error Message      FICON-6-PDCM_CHANGE: VSAN [dec] port-address [dec] prohibit mask set 
to [chars] 

Explanation    The FICON Prohibit Dynamic Connectivity Mask (PDCM) for this port has changed. VSAN [dec], port address [dec] prohibit mask (PDCM) is now set to [chars]

Recommended Action    No action is required.

Error Message      FICON-6-PORT_SWAP: port number [dec] [dec] swapped 

Explanation    FICON portnumbers swapped

Recommended Action    No action is required.

Error Message      FICON-6-VSAN_DISABLED: FICON disabled on VSAN [dec] 

Explanation    FICON has been disabled on the given VSAN

Recommended Action    No action is required.

Error Message      FICON-6-VSAN_ENABLED: FICON enabled on VSAN [dec] 

Explanation    FICON has been enabled on the given VSAN

Recommended Action    No action is required.

FLEXLINK Messages

FLEXLINK-2

Error Message      FLEXLINK-2-FLEXLINK_FEATURE_DISABLE_FAILED_CONFIG: Disablement of 
feature Flexlink failed. Please remove Flexlink related configs from interfaces. 

Explanation    Disablement of Flexlink service failed

Recommended Action    No action is required.

Error Message      FLEXLINK-2-FLEXLINK_FEATURE_ENABLE_FAILED_PLATFORM: Enablement of 
feature Flexlink failed. Flexlink is not supported on [chars] platforms. 

Explanation    Enablement of Flexlink service failed

Recommended Action    No action is required.

Error Message      FLEXLINK-2-FLEXLINK_FEATURE_ENABLE_FAILED_VPC: Enablement of feature 
Flexlink failed. Please disable feature VPC first. 

Explanation    Enablement of Flexlink service failed

Recommended Action    No action is required.

Error Message      FLEXLINK-2-FLEXLINK_FWDING_EVSEQ_FAIL: Port state change request to 
Forwarding Manager error [hex] [[chars]] vdc [dec]. Port [chars] will be error 
disabled. 

Explanation    Forwarding Manager set port state has failed or timed out.

Recommended Action    No action is required.

FLEXLINK-5

Error Message      FLEXLINK-5-FLEXLINK_DISABLED: Flexlink Manager disabled 

Explanation    Flexlink Service Disabled

Recommended Action    No action is required.

Error Message      FLEXLINK-5-FLEXLINK_ENABLED: Flexlink Manager enabled 

Explanation    Flexlink Service Enabled

Recommended Action    No action is required.

Error Message      FLEXLINK-5-LOOP_REMOVE_CONFIG: Removing Switchport Backup 
configuration for pair ([chars]) on port-channel deletion to prevent loops 

Explanation    Switchport Backup port channel deletion removing config

Recommended Action    No action is required.

Error Message      FLEXLINK-5-PREEMPTION: Switchport Backup interface [chars] 
preemption of [chars] for [chars] 

Explanation    Switchport Backup interface preemption

Recommended Action    No action is required.

FLOGI Messages

FLOGI-1

Error Message      FLOGI-1-MSG_FDISC_REJECT_TOO_MANY_LOGINS: [VSAN [dec], Interface 
[chars]] FDISC rejected - this interface has reached the max num of N-Ports ([dec]) 

Explanation    An FDISC was rejected because the F-Port has reached the maximum allowed number of devices.

Recommended Action    Check the configuration of the NPIV device connected to the port.

Error Message      FLOGI-1-MSG_FLOGI_REJECT_FCID_ERROR: [VSAN [dec], Interface [chars]] 
FLOGI rejected - FCID allocation failed. 

Explanation    An FLOGI was rejected because the FCID allocation failed.

Recommended Action    Check the fcid-interop configuration, purge the persistency table and check the output of "show flogi database details" and see if any of the "A area FCID allocation" entries can be turned to single fcid allocation as per Configuration Guide

Error Message      FLOGI-1-MSG_FLOGI_REJECT_TOO_MANY_LOGINS: [VSAN [dec], Interface 
[chars]] FLOGI rejected - this interface has reached the max num of NL-Ports 
([dec]) 

Explanation    An FLOGI was rejected because the FL-Port has reached the maximum allowed number of devices.

Recommended Action    Reduce the number of devices on the loop

Error Message      FLOGI-1-MSG_NPIV_NOT_SUPPORTED_WITH_TRUNKING: [VSAN [dec], Interface 
[chars]] NPIV not supported - on this platform, NPIV is not supported on trunking 
interfaces 

Explanation    The N_Port requested NPIV, but this platform does not support NPIV on trunking F_Ports.

Recommended Action    Disable NPIV, or move the N_Port to a switch that supports NPIV on trunking F_Ports

FLOGI-2

Error Message      FLOGI-2-MSG_FLOGI_REJECT_NO_ACL_TCAM_AVAILABLE: [VSAN [dec], 
Interface [chars]] FLOGI rejected - ACLTCAM resource exausted 

Explanation    An FLOGI was rejected because the ACLTCAM hardware resource is completely used.

Recommended Action    Reduce the number of nodes.

FLOGI-4

Error Message      FLOGI-4-MSG_VF_FLOGI_FROM_NON_CISCO_OUI: [VSAN [dec], Interface 
[chars]] FLOGI with VF bit set from OUI [hex]:[hex]:[hex] (nwwn: [chars]) 

Explanation    This interface received an FLOGI with VF bit set from a non CISCO OUI; in this release Virtual Fabrics are not supported on interfaces connected to third-party devices

Recommended Action    Set the trunk mode of this interface to off

FLOGI-5

Error Message      FLOGI-5-MSG_FLOGI_DROP_DUE_TO_SUSPENDED_VSAN: [VSAN [dec], Interface 
[chars]] FLOGI (pwwn: [chars]) has been dropped because the VSAN is suspended on 
this trunking interface 

Explanation    The switch received an FLOGI from a trunking interface on a VSAN which has been suspended; the FLOGI frame has been dropped.

Recommended Action    To bring up the VSAN again on the trunking port, remove it from the allowed VSAN list and add it again

Error Message      FLOGI-5-MSG_FLOGI_DUPLICATE_WWPN: [VSAN [dec], Interface [chars]] 
FLOGI (pwwn: [chars]) has been dropped because the host has a duplicate WWPN 

Explanation    The switch received an FLOGI from the interface, which has a duplicate PWWN value.

Recommended Action    No action is required.

Error Message      FLOGI-5-MSG_IF_REINIT_ALPA_CONFLICT: [VSAN [dec], Interface [chars]] 
FL/TL interface [chars] re-initialized as ALPA - PWWN map conflict occurred. 

Explanation    The FL/TL interface is re-initialized as ALPA used by device conflicts with an existing FLOGI session after the Loop Initialization Protocol (LIP). All the devices will re-login with new ALPA and PWWN mapping

Recommended Action    No action is required.

Error Message      FLOGI-5-MSG_PORT_LOGGED_IN: [VSAN [dec], Interface [chars]] Nx Port 
[chars] with FCID [chars] logged IN. 

Explanation    Nx port logged in with the specified information.

Recommended Action    No action is required.

Error Message      FLOGI-5-MSG_PORT_LOGGED_OUT: [VSAN [dec], Interface [chars]] Nx Port 
[chars] logged OUT. 

Explanation    Nx port logged out. The following commands will help determine why this Nx port logged out: showinterface,showVSAN,showmodule''

Recommended Action    No action is required.

Error Message      FS-DAEMON-2-FSD_ENOSPC_BOOTFLASH: Due to insufficient space, [chars] 
image could not be copied to standby bootflash. [chars] image is not present on 
standby. Please copy '[chars]' manually. 

Explanation    Move system images from RAM to bootflash to free up some memory

Recommended Action    Please remove some unnecessary files on bootflash using 'delete' CLI command and copy images from active supervisor or from remote location

Error Message      FS-DAEMON-6-FSD_ENOSPC_LOGFLASH: System logflash usage has reached 
[dec]%. You may delete some old files on logflash to free up space 

Explanation    System logflash space is almost full

Recommended Action    Use clearcorearchived'or'delete'CLItofreeupspaceonlogflash'

Error Message      FS-DAEMON-6-FSD_ENOSPC_ROOT: System root usage has reached [dec]%. 
You may delete some old files from root or /var/log to free up space 

Explanation    System root space is almost full

Recommended Action    Use clearcorearchived'or'delete'CLItofreeupspaceonrootdiror/var/log'

Error Message      FS-DAEMON-6-FSD_ENOSPC_TMP: System temporary directory usage has 
reached [dec]%. 

Explanation    System /tmp space usage.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FS-DAEMON-6-FSD_ENOSPC_VAR_SYSMGR: System Sysmgr temporary directory 
usage has reached [dec]%. 

Explanation    System /var/sysmgr space usage

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FS-DAEMON-6-FSD_REEXPORT_NFS: Re-exported NFS mounts 

Explanation    Exported NFS mounts are not visible in kernel and had to be reexported

Recommended Action    Please use showsysteminternalflash'tomakesuretherearenoStaleNFShandles'

FSCM Messages

FSCM-2

Error Message      FSCM-2-FABRIC_START_CFG_MGR_PROGRAM_EXIT: Fabric Start Cfg Mgr 
daemon exiting: [chars] 

Explanation    FABRIC_START_CFG_MGR daemon is exiting.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FSPF Messages

FSPF-2

Error Message      FSPF-2-SHUTDOWN: Routing daemon shutting down : [chars] 

Explanation    FSPF routing daemon is shutting down because of [chars] reason.

Recommended Action    This is a severe bug. Provide the reason provided and the log files for FSPF.

FSPF-3

Error Message      FSPF-3-BAD_FC2_PKT: Received bad FC2 packet on interface [chars] : 
[chars] 

Explanation    FSPF received a bad FC2 packet on [chars] interface , error description is [chars].

Recommended Action    FSPF daemon has received a bad FC frame. Provide the output of debugfc2pkt'.'

Error Message      FSPF-3-CHECKSUM_FAIL: Checksum test failed for LSR domain [dec] 

Explanation    Periodic database checksum test failed for LSR for domain [dec]

Recommended Action    This indicates that the internal database got corrupted because of some memory corruption bug. Provide output of showfspfdatabase'.Mayneedtopowercycletheswitch'

Error Message      FSPF-3-FC2_PROC_ERR: Error in processing [chars] packet on interface 
[chars], Error = [chars] 

Explanation    An error occurred in processing a [chars] FC2 packet on [chars] interface. The internal error code is [chars].

Recommended Action    Turn on debugfspferror'togetmoreinformation.MakesurethereisnomisconfigurationofFSPFparametersonthet woendsoftheinterface.Provideoutputof'showfspfvsanx''showfspfvsanxinterface'and'debugfspffcpkt' forthespecificinterface'

Error Message      FSPF-3-FLOOD_ERR: Error in flooding the local LSR , Error = [chars] 

Explanation    FSPF had an error in flooding the local LSR , error description is [chars].

Recommended Action    Provide output of debugfspfflood','debugfspferror'.Iferrorisreportedintransmittingpacketcheckifinterfaceisupandturn on'debugfc2error''

Error Message      FSPF-3-HELLO_MISMATCH: Mismatch in [chars] in the Hello packet on 
interface [chars] 

Explanation    There is a mismatch in the [chars] entry in the hello packet received on interface [chars]. The packet will be dropped.

Recommended Action    Check the configuration of hello or dead interval on the switches on the two ends of the interface to see if there is a mismatch.

Error Message      FSPF-3-INTF_TIMER_ERR: Error in processing interface timer event 
[chars] for interface [chars] , error = [chars] 

Explanation    FSPF had an error in processing timer event for interface chars, error is [chars].

Recommended Action    Provide output of debugfspferror''

Error Message      FSPF-3-IPC_PROC_ERR: Error in processing IPC message : Opcode = 
[dec], Error code = [hex] 

Explanation    FSPF had an error in processing message of [dec] opcode , the internal error code is [dec].

Recommended Action    Possibly some wrong IPC message is received by FSPF . Provide output of debugfspfmtspkt'and'debugfspferror'trace.'

Error Message      FSPF-3-LOCK_FAIL: FSPF failure in gaining lock 

Explanation    There is a software failure in gaining lock of the shared resource between FSPF threads.

Recommended Action    Provide output of debugfspfall''

Error Message      FSPF-3-MTS_MSG_BEFORE_GSYNC: FSPF in standby received MTS message 
opcode = [hex] before GSYNC 

Explanation    FSPF in standby received an MTS message of opcode [dec] before receiving the GSYNC message.

Recommended Action    Provide output of debugfspfmtspkt''

Error Message      FSPF-3-RIB_ERR: Error in RIB : [chars] 

Explanation    FSPF had an error in interacting with RIB, error description is [chars].

Recommended Action    Check if rib application is running using showprocesses'.Provideoutputof'debugfspfroute'andRIBdebugtraces.'

Error Message      FSPF-3-ROUTE_COMPUTE_ERR: Error in computing or sending routes : 
Error = [chars] 

Explanation    FSPF had an error in computing routes , error description is [chars].

Recommended Action    Provide the error code and output of debugfspferror'and'debugfspfroute'ifproblemisreproducible'

Error Message      FSPF-3-UNLOCK_FAIL: FSPF failure in releasing lock 

Explanation    There is a software failure in releasing lock of the shared resource between FSPF threads.

Recommended Action    Provide output of debugfspfall''

Error Message      FSPF-3-VSAN_TIMER_ERR: Error in processing VSAN timer event [chars], 
error description = [chars] 

Explanation    FSPF had an internal error in processing timer event , error description is [chars].

Recommended Action    Provide output of debugfspferror''

FSPF-4

Error Message      FSPF-4-FC2_DOWN_INTF: Received FC2 packet on DOWN interface [chars] 

Explanation    FSPF received a FC2 packet on inactive interface [chars] .

Recommended Action    This message may be printed for the first FSPF packet when an interface is brought up. If the message is seen continuously check if FSPF is disabled on one end for the interface or the VSAN. Otherwise check showinterface'outputtoseeifinterfaceisphysicallyuponlyononeside.Alsocheckifthereisanyerrormess ageprintedforIPC_PROC_ERR'

Error Message      FSPF-4-FC2_DOWN_VSAN: Received FC2 packet on inactive vsan 

Explanation    FSPF received a FC2 packet on inactive vsan.

Recommended Action    If message seen continuously check if FSPF is disabled on the VSAN Investigate if VSAN is active and valid domain has been assigned on the switch Also check if IPC_PROC_ERR message is printed in the syslog

Error Message      FSPF-4-ILLEGAL_FSM_EVENT: Illegal FSM event for state [chars] in 
interface [chars] 

Explanation    An illegal protocol event has occurred for the FSPF state machine. The old state was [chars] for the interface [chars].

Recommended Action    It is possible to get this message if some protocol packet gets dropped but the it should recover and move back to FULL state. Do showfspfinterface'tocheckthestateoftheinterface.IfitisstuckinstateotherthanFULLprovideoutputof'd ebugfspfevent'and'debugfspffcpkt'fortheinterfacesinvolved.'

Error Message      FSPF-4-LSR_DROPPED: [chars], Dropping LSR [dec] received on interface 
[chars] 

Explanation    A LSR packet is dropped due to [chars] reason. LSR belonged to domain [dec] and was received on interface [chars].

Recommended Action    Provide the reason given for dropping the LSR and output of debugfspffcpkt'Ifthereasonischecksumfailureinvestigatepossiblepacketcorruptionortruncation'

Error Message      FSPF-4-LSR_MIN_LS_ARRIVAL: Packet arrived before MIN_LS_ARRIVAL, 
Dropping LSR [dec] on interface [chars] 

Explanation    A LSR packet is dropped as it arrived before MIN_LS_ARRIVAL. LSR belonged to domain [dec] and was received on interface [chars].

Recommended Action    This can occur in transient situation and protocol recovers by retransmitting the LSR. If the message is seen continuously provide output of debugfspfflood','debugfspfretrans'and'debugfspferror'.Themessagemaybeseenmoreoftenwhenintero peratingwithothervendors'

Error Message      FSPF-4-LSU_RX_INIT: Dropping LSU received in state INIT on interface 
[chars] 

Explanation    A LSU packet is dropped as interface [char] is in INIT state when it received the LSU.

Recommended Action    This can occur in some transient situation. If the problem persists provide output of showfspfvsanxinterface'and'debugfspffcpkt'and'debugfspfeventvsanx''

FSPF-5

Error Message      FSPF-5-STARTING: Routing daemon started 

Explanation    FSPF routing daemon has been started.

Recommended Action    No action is required.

FSPF-6

Error Message      FSPF-6-ADD_LSR: New LSR added for domain [dec] 

Explanation    A new LSR is added to the database for domain [dec] .

Recommended Action    No action is required.

Error Message      FSPF-6-DELETE_LSR: LSR deleted for domain [dec] 

Explanation    The LSR for domain [dec] is deleted from the database.

Recommended Action    No action is required.

Error Message      FSPF-6-INTF_OPER_DOWN: Down on interface [chars] 

Explanation    FSPF has become operationally down on interface [chars].

Recommended Action    No action is required.

Error Message      FSPF-6-INTF_OPER_UP: Up on interface [chars] 

Explanation    FSPF has become operational on interface [chars].

Recommended Action    No action is required.

Error Message      FSPF-6-MAX_AGE: LSR [dec] reached Maxage 

Explanation    The LSR for domain [dec] reached the maximum age and will be deleted from all the connected switches .

Recommended Action    No action is required.

Error Message      FSPF-6-ROLLOVER: Rolling over the incarnation number of Local LSR 

Explanation    The incarnation number of local LSR reached the maximum value and is rolling over.

Recommended Action    No action is required.

Error Message      FSPF-6-SELF_ORIGINATED: Received local LSR with higher incarnation 
number 

Explanation    A LSR for the local domain was received with incarnation number higher than the one in database. This situation should only occur initially on a topology change. If this situation persists the domain assignment of switches may not be unique

Recommended Action    If this message is received continuously check if domain assignment is unique in the fabric.

Error Message      FSPF-6-STATE_CREATED: Internal state created [chars] 

Explanation    FSPF has created its internal state stateless/stateful [chars].

Recommended Action    No action is required.

Error Message      FSPF-6-VSAN_OPER_DOWN: Down on vsan 

Explanation    FSPF has become operationally down on VSAN.

Recommended Action    No action is required.

Error Message      FSPF-6-VSAN_OPER_UP: Up with local domain [dec] 

Explanation    FSPF has started with local domain [dec].

Recommended Action    No action is required.

FSPF-7

Error Message      FSPF-7-ROUTE_THREAD_STARTED: Thread number [dec] started 

Explanation    Route computation thread number [dec] has been started for FSPF.

Recommended Action    No action is required.

FWM Messages

FWM-0

Error Message      FWM-0-FCFIB_EMERG: [chars] 

Explanation    Fcfib caused a system failure

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FWM-1

Error Message      FWM-1-FCFIB_ALERT: [chars] 

Explanation    Fcfib caused failures in other services

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-1-FCFIB_HW_NO_VSAN_DOM: No hardware [chars] resources for route 
creation to VSAN [dec] Domain [dec] 

Explanation    Hardware does not have sufficient resources to create this route.

Recommended Action    Please delete unused VSANs or assign common Domain numbers to existing VSANs.

Error Message      FWM-1-FCFIB_HW_NO_VSAN: No hardware [chars] resources for route 
creation to VSAN [dec] 

Explanation    Hardware does not have sufficient resources to create this route.

Recommended Action    Please delete unused VSANs.

Error Message      FWM-1-FCFIB_HW_PC_LIMIT: Failed to create [chars], hardware limit of 
[dec] would be exceeded 

Explanation    The number of hardware SAN Port Channels is limited by the platform.

Recommended Action    Please configure fewer SAN Port Channels.

Error Message      FWM-1-FCFIB_LICENSE_UNAVAILABLE: License: [chars] is not installed. 
System will not provide FC switching. 

Explanation    Fibre Channel license is unavailable. System will not provide FC switching.

Recommended Action    Please install the license file to continue using the feature.

FWM-2

Error Message      FWM-2-FCFIB_CRIT: [chars] 

Explanation    Fcfib encountered a catastrophic error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-FWM_ASSERT_FAILURE: stack [[chars]] 

Explanation    Critical assertion failed in forwarding manager

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-FWM_CONFIG_ERROR: Wrong configuration. Ignoring configuration. 

Explanation    Configuration specified by the user is wrong. Configuration will be ignored.

Recommended Action    No action is required.

Error Message      FWM-2-FWM_CTS_CFG_INCONSISTENT: CTS config is inconsistent across 
interface [chars] and [chars]. Interface going error-disabled. CTS config should 
be consistent across all the interfaces with same FEX ID 

Explanation    CTS config inconsistent across interfaces in the fex

Recommended Action    No action is required.

Error Message      FWM-2-FWM_CTS_PC_CFG_INCONSISTENT: CTS config is inconsistent across 
interface [chars] and [chars]. Interface going error-disabled. CTS config should 
be consistent across all the members of a Port-channel interface 

Explanation    CTS config inconsistent across Port-channel members

Recommended Action    No action is required.

Error Message      FWM-2-FWM_DUPLICATE_UNICAST_MAC_REGISTRATION: Unicast MAC address 
[chars] vlan [dec] registered on interface [chars] before deregistering on 
interface [chars] 

Explanation    Duplicate unicast MAC registration observed

Recommended Action    No action is required.

Error Message      FWM-2-FWM_LC_INSERT_FAILURE: Failure([chars]) in FWM during LC 
insert processing 

Explanation    Failure encountered in FWM during LC insert processing

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-FWM_OIFL_MCAST_IDX_LIMIT_REACHED: [chars] 

Explanation    The number of of multicast indices in the system have been exhausted. Cannot learn any more new multicast groups or create new vlans.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-FWM_PSS_RESTORE_ERROR: FwM PSS restoration has failed. Error: 
[chars] 

Explanation    PSS restoration of FwM has failed during stateful restart or non disruptive upgrade.

Recommended Action    No action is required.

Error Message      FWM-2-FWM_SPAN_EGR_MCAST_ERROR: FwM SPAN fex source programming has 
failed. Error: [chars] 

Explanation    One or more fex ports/port channels which are sources in monitor sessions are part of

Recommended Action    No action is required.

Error Message      FWM-2-FWM_VE_NOT_SUPPORTED: FCoE cannot be enabled for E mode (VE) 
on this platform 

Explanation    FCoE cannot be enabled for E mode (VE) on Oregon switch with GATOS B or below.

Recommended Action    No action is required.

Error Message      FWM-2-FWM_VLAN_LIMIT_REACHED: [chars] 

Explanation    Max vlan limit is reached. Cannot create a vlan. Temporary exhaustion of vlan resources.

Recommended Action    No action is required.

Error Message      FWM-2-STM_LEARNING_RE_ENABLE: Re enabling dynamic learning on all 
interfaces 

Explanation    Re enabling learning on all interfaces after disable period expired

Recommended Action    No action is required.

Error Message      FWM-2-STM_LIMIT_REACHED: [chars] 

Explanation    System station table reached its capacity - no further MAC addresses could be programmed - administration intervention may be required to avoid this problem in future

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-STM_LOOP_DETECT: [chars] 

Explanation    System detected loops in the network - administration intervention may be required to avoid this problem in future

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-2-STM_MCAST_PROG_RE_ENABLE: Re enabling programming multicast 
entries 

Explanation    Re enabling programming new multicast entries because number of entries reached below threshold

Recommended Action    No action is required.

Error Message      FWM-2-STM_RAPID_MOVES: [chars] 

Explanation    System detected rapid mac moves in the network - administrator intervention may be required to avoid this problem in future

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FWM-3

Error Message      FWM-3-FCFIB_ERR: [chars] 

Explanation    Fcfib encountered an error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-3-FCFIB_NO_MEM: Out of memory 

Explanation    Fcfib does not have enough memory to continue proper operation.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-3-FWM_DCEFIB_ERROR: [chars] 

Explanation    L2MP Forwarding Error.

Recommended Action    No action is required.

FWM-4

Error Message      FWM-4-FCFIB_CPU_HOG: Inactive or busy 

Explanation    Either fcfib was not scheduled to run, or fcfib was busy, and fcfib did not service the message or timer queue for an extended period.

Recommended Action    Please perform debugfwmerror',thenrecreatetheoperationscenario,tofindoutmoredetails.'

Error Message      FWM-4-FWM_ENM_MAC_AGED: mac address [chars] on vlan [dec] is aged out 

Explanation    The mac address on a vlan has been aged out.

Recommended Action    No action is required.

Error Message      FWM-4-STM_LEARNING_OVERLOAD: [chars] 

Explanation    System getting overloaded due to learning processes

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

FWM-6

Error Message      FWM-6-FWM_ASSERT_FAILURE_INFO_LEVEL: stack [[chars]] 

Explanation    Assertion failed in forwarding manager

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      FWM-6-FWM_DCEFIB_INFO: [chars] 

Explanation    L2MP Forwarding Information.

Recommended Action    No action is required.

Error Message      FWM-6-MAC_MOVE_NOTIFICATION: Host [chars] in vlan [dec] is flapping 
between port [chars] and port [chars] 

Explanation    Notification of a MAC address moving as per configuration

Recommended Action    No action is required.

Error Message      FWM-6-STM_THRESHOLD_NOTIFICATION: Station table reached [dec]% of 
the total capacity (num entries [dec], total limit [dec]) 

Explanation    Station table capacity utilization message as per configured threshold values

Recommended Action    No action is required.

Error Message      FWM-6-UUFB_CHANGE_NOTIFICATION: Unknown unicast flood blocking has 
been [chars] 

Explanation    Notification of unknown unicast flood blocking being enabled or disabled

Recommended Action    No action is required.

Error Message      FWM-6-UUFB_CONFIG_FAILURE: Unknown unicast flood blocking was not 
set due to incompatible version of VEM slot - [dec] 

Explanation    VEM version does not support UUFB. Config will not be sent to VEM.

Recommended Action    No action is required.

GLBP Messages

GLBP-2

Error Message      GLBP-2-GLBP_URIB_INIT_ERROR: [chars] 

Explanation    Unicast routing initialization failed and the GLBP process terminated

Recommended Action    Please check syslog messages for URIB failures and rectify the problem

GLBP-3

Error Message      GLBP-3-GLBP_ARP_ADD_FAILED: failed to add [chars]/[chars] in arp 
table 

Explanation    The system was unable to add the GLBP vIP into the arp table

Recommended Action    Please check syslog messages for ARP failures and rectify the problem

Error Message      GLBP-3-GLBP_ARP_DEL_FAILED: failed to delete [chars]/[chars] in arp 
table 

Explanation    The system was unable to delete the GLBP vIP from the arp table

Recommended Action    Please check syslog messages for ARP failures and rectify the problem

Error Message      GLBP-3-GLBP_FEATURE_MANAGER_ERROR: [chars]: [chars] 

Explanation    There was a problem in GLBP interaction with feature manager.

Recommended Action    Please check the reason for error using feature manager and rectify the problem

Error Message      GLBP-3-GLBP_IP_JOIN_GROUP_FAILED: [chars]: failed to join glbp 
multicast address group 

Explanation    The system was unable to peform a join to start receiving GLBP protocol packets.

Recommended Action    Please check syslog messages for IP failures and rectify the problem

Error Message      GLBP-3-GLBP_IP_LEAVE_GROUP_FAILED: [chars]: failed to leave glbp 
multicast address group 

Explanation    The system was unable to peform a leave to stop receiving GLBP protocol packets.

Recommended Action    Please check syslog messages for IP failures and rectify the problem

Error Message      GLBP-3-GLBP_MAC_ADD_FAILED: fwd [dec] failed to add [chars] in mac 
table (error [hex]) 

Explanation    The system was unable to add the GLBP mac address into the mac addresss table

Recommended Action    Please check syslog messages for L2FM failures and rectify the problem

Error Message      GLBP-3-GLBP_MAC_DEL_FAILED: fwd [dec] failed to delete [chars] in 
mac table (error [hex]) 

Explanation    The system was unable to delete the GLBP mac address from the mac addresss table

Recommended Action    Please check syslog messages for L2FM failures and rectify the problem

Error Message      GLBP-3-GLBP_ROUTE_ADD_FAILED: failed to add [chars] in routing table 

Explanation    The system was unable to add the GLBP vIP address into the unicast routing table

Recommended Action    Please check syslog messages for URIB failures and rectify the problem

Error Message      GLBP-3-GLBP_ROUTE_DEL_FAILED: failed to delete [chars] in routing 
table 

Explanation    The system was unable to delete the GLBP vIP address from the unicast routing table

Recommended Action    Please check syslog messages for URIB failures and rectify the problem

GLBP-4

Error Message      GLBP-4-BADAUTH: Bad authentication received from [chars] 

Explanation    Two routers participating in a Gateway Load Balancing Protocol group have a valid authentication string that does not match.

Recommended Action    Use the glbp authentication interface command to repair the Gateway Load Balancing Protocol authentication discrepancy between the local system and the one whose IP address is reported

Error Message      GLBP-4-BADVIP1: address [chars] is in the wrong subnet for this 
interface 

Explanation    The Gateway Load Balancing Protocol virtual IP address is not within the subnet configured on this interface.

Recommended Action    Configure the virtual IP address of Gateway Load Balancing Protocol to be within the subnet configured on this interface.

Error Message      GLBP-4-BADVIP2: address [chars] in the wrong subnet for this 
interface is not learned 

Explanation    The Gateway Load Balancing Protocol virtual IP address contained in the hello message cannot be learned. It is not within the subnet configured on this interface.

Recommended Action    Check the configuration on all Gateway Load Balancing Protocol routers.

Error Message      GLBP-4-BADVIP3: address [chars] is the broadcast address for this 
interface 

Explanation    The Gateway Load Balancing Protocol virtual IP address is a broadcast address for this interface.

Recommended Action    Configure the virtual IP address of Gateway Load Balancing Protocol to be a non broadcast address.

Error Message      GLBP-4-DIFFVIP1: active router virtual IP address [chars] is 
different from the locally configured virtual IP address [chars] 

Explanation    The Gateway Load Balancing Protocol virtual IP address contained in the Hello message from the Active router is different to that configured locally.

Recommended Action    Check the configuration on all Gateway Load Balancing Protocol routers

Error Message      GLBP-4-DUPADDR: Duplicate address on [chars] 

Explanation    The IP address in a Gateway Load Balancing Protocol message received on the interface is the same as the IP address of its own router. This condition may be caused by a misconfiguration or because of a malfunctioning switch.

Recommended Action    Check the configurations on all the Gateway Load Balancing Protocol routers, and ensure that any switches are functioning properly

Error Message      GLBP-4-DUPVIP1: address [chars] already assigned to interface [chars] 
grp [dec] 

Explanation    The Gateway Load Balancing Protocol virtual IP address contained in the hello message cannot be learned. It is already assigned to a different Gateway Load Balancing Protocol group.

Recommended Action    Check the configuration on all Gateway Load Balancing Protocol routers

Error Message      GLBP-4-DUPVIP2: address [chars] already assigned to this interface 

Explanation    The Gateway Load Balancing Protocol virtual IP address contained in the hello message cannot be learned. It is already assigned to this interface.

Recommended Action    Check the configuration on all Gateway Load Balancing Protocol routers.

Error Message      GLBP-4-DUPVIP3: address [chars] already assigned to another interface 
[chars] 

Explanation    The Gateway Load Balancing Protocol virtual IP address contained in the hello message cannot be learned. It is already assigned to, or overlaps with, an address on another interface or application.

Recommended Action    Check the configuration on all Gateway Load Balancing Protocol routers.

Error Message      GLBP-4-GLBP_ARP_RESP_FAILED: failed to send arp response 
[chars]/[chars] 

Explanation    The system was unable to send the arp response for vIP

Recommended Action    Please check syslog messages for ARP failures and rectify the problem

GLBP-5

Error Message      GLBP-5-ACTIVE_CHANGE: Active gateway is [chars] 

Explanation    The Gateway Load Balancing Protocol has changed active gateway.

Recommended Action    No action is required

Error Message      GLBP-5-FWDSTATECHANGE: fwd [dec] state changed from [chars] to 
[chars] 

Explanation    The Gateway Load Balancing Protocol forwarder has changed state.

Recommended Action    No action is required

Error Message      GLBP-5-FWD_CREATE: fwd [dec] created 

Explanation    The Gateway Load Balancing Protocol forwarder has been created.

Recommended Action    No action is required

Error Message      GLBP-5-FWD_DELETE: fwd [dec] deleted 

Explanation    The Gateway Load Balancing Protocol forwarder has been removed.

Recommended Action    No action is required

Error Message      GLBP-5-FWD_OWNER: fwd [dec] owner mac is [chars] 

Explanation    The Gateway Load Balancing Protocol forwarder has changed the owner MAC address.

Recommended Action    No action is required

Error Message      GLBP-5-FWD_VMAC: fwd [dec] virtual mac is [chars] 

Explanation    The Gateway Load Balancing Protocol forwarder has changed the virtual MAC address.

Recommended Action    No action is required

Error Message      GLBP-5-FWD_WEIGHTING: fwd [dec] weighting is [dec] 

Explanation    The Gateway Load Balancing Protocol forwarder has changed the weighting.

Recommended Action    No action is required

Error Message      GLBP-5-GRPSTATECHANGE: state changed from [chars] to [chars] 

Explanation    The Gateway Load Balancing Protocol gateway has changed state.

Recommended Action    No action is required

Error Message      GLBP-5-MEMBER_ADD: member [chars] [chars] added 

Explanation    The Gateway Load Balancing Protocol gateway has added a member.

Recommended Action    No action is required

Error Message      GLBP-5-MEMBER_REMOVE: member [chars] [chars] removed 

Explanation    The Gateway Load Balancing Protocol gateway has removed a member.

Recommended Action    No action is required

Error Message      GLBP-5-PRIORITY: [chars] gateway priority changed to [dec] 

Explanation    The Gateway Load Balancing Protocol gateway has changed priority.

Recommended Action    No action is required

Error Message      GLBP-5-STANDBY_CHANGE: Standby gateway is [chars] 

Explanation    The Gateway Load Balancing Protocol has changed standby gateway.

Recommended Action    No action is required

Error Message      GLBP-5-TIMER: [chars] timer changed to [chars] 

Explanation    The Gateway Load Balancing Protocol gateway has learnt timers.

Recommended Action    No action is required

Error Message      GLBP-5-VIPLEARN: learnt virtual ip address [chars] 

Explanation    The Gateway Load Balancing Protocol gateway has learnt virtual IP address.

Recommended Action    No action is required

Error Message      GLBP-5-VIPUNLEARN: unlearnt virtual ip address [chars] 

Explanation    The Gateway Load Balancing Protocol gateway has unlearnt virtual IP address.

Recommended Action    No action is required

Error Message      GLBP-5-WEIGHTING: weighting changed to [dec] 

Explanation    The Gateway Load Balancing Protocol gateway has changed the weighting.

Recommended Action    No action is required

HSRP_ENGINE Messages

HSRP_ENGINE-3

Error Message      HSRP_ENGINE-3-BFD_GLOBAL_SESSION_REMOVAL_ERROR: Failed to remove all 
the HSRP-BFD sessions([hex] [hex]), Refer logs 

Explanation    Refer logs for more details

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-BFD_IF_SESSION_REMOVAL_ERROR: Failed to remove few 
HSRP-BFD sessions([hex] [hex]), Refer logs 

Explanation    Refer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-BFD_SESSION_ADD_ERROR: Failed to add few HSRP-BFD 
sessions([hex] [hex]), Refer logs 

Explanation    TRefer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-BFD_SESSION_CREATION_ERROR: Failed to create BFD 
session information([hex] [hex]), Refer logs 

Explanation    Refer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-BFD_SESSION_REMOVAL_ERROR: Failed to remove few 
HSRP-BFD sessions([hex] [hex]), Refer logs 

Explanation    Refer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-ERROR_IN_ADD_VIP_TO_U6RIB: Failed to Add VIP [chars] 
to U6RIB (errno [hex]), Refer logs 

Explanation    Refer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-ERROR_IN_DEL_VIP_FROM_U6RIB: Failed to delete VIP 
[chars] from U6RIB (errno [hex]), Refer logs 

Explanation    Refer logs for more details.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-3-NOSOCKET: Unable to open socket 

Explanation    The system was unable to initialize an IP connection for the Hot Standby protocol.

Recommended Action    Make sure that there is at least one interface configured to run IP.

HSRP_ENGINE-4

Error Message      HSRP_ENGINE-4-BADAUTH2: Bad authentication from [chars] 

Explanation    Two routers participating in HSRP disagree on the valid authentication string.

Recommended Action    Use the HSRP authentication command to repair the HSRP authentication discrepancy between the local system and the one whose IP address is reported.

Error Message      HSRP_ENGINE-4-BADAUTH: Bad authentication from [chars], group [dec], 
remote state [chars] 

Explanation    Two routers participating in HSRP disagree on the valid authentication string.

Recommended Action    Use the HSRP authentication command to repair the HSRP authentication discrepancy between the local system and the one whose IP address is reported.

Error Message      HSRP_ENGINE-4-DIFFVIP1: [chars] Grp [dec] active routers virtual IP 
address [chars] is different to the locally configured address [chars] 

Explanation    The HSRP virtual IP address contained in the Hello message from the Active router is different to that configured locally.

Recommended Action    Check the configuration on all HSRP routers.

Error Message      HSRP_ENGINE-4-DUPADDR: Duplicate address %i on [chars], sourced by %e 

Explanation    The IP address in an HSRP message received on the interface is the same as the routersownIPaddress.Thismaybebecauseofmisconfiugration,orbecauseofamalfunctioningswitch'

Recommended Action    Check the configurations on all the HSRP routers, and make sure that any switches you have are functioning properly.

Error Message      HSRP_ENGINE-4-DUPVIP1: [chars] Grp [dec] address [chars] is already 
assigned to a HSRP group on this interface 

Explanation    The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to a different HSRP group.

Recommended Action    Check the configuration on all HSRP routers.

Error Message      HSRP_ENGINE-4-DUPVIP2: [chars] Grp [dec] address [chars] is already 
assigned on this interface 

Explanation    The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to this interface.

Recommended Action    Check the configuration on all HSRP routers.

Error Message      HSRP_ENGINE-4-DUPVIP3: [chars] Grp [dec] address [chars] is already 
assigned to, or overlaps with, an address on another interface or application 

Explanation    The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to, or overlaps with, an address on another interface or application.

Recommended Action    Check the configuration on all HSRP routers.

HSRP_ENGINE-5

Error Message      HSRP_ENGINE-5-ACTIVEROUTERPRIORITY: Interface [chars] [chars] Grp 
[dec] Active router priority changed to [dec] 

Explanation    The priority of the Active router for the group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-ACTIVE_CHANGE: Interface [chars] [chars] Grp [dec] 
Active router is [chars] 

Explanation    The Active router for the group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-AUTOCONFIG_VIPLEARN: Interface [chars] grp [dec] 
learnt autoconfig virtual ip address [chars] 

Explanation    The local router has generate virtual ip address

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-GRPSTATECHANGE: Interface [chars] [chars] Grp [dec] 
state changed from [chars] to [chars] reason [chars] 

Explanation    The HSRP router has changed state

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-MACADDRESS_CHANGE: Interface [chars] [chars] Grp [dec] 
mac-address changed to [chars] 

Explanation    The mac address of the group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-PRIORITY: Interface [chars] [chars] Grp [dec] priority 
changed to [dec] 

Explanation    The current priority of the HSRP group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-STANDBYROUTERPRIORITYCHANGE: Interface [chars] [chars] 
Grp [dec] Standby router priority changed to [dec] 

Explanation    The priority of the Standby router for the group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-STANDBY_CHANGE: Interface [chars] [chars] Grp [dec] 
Standby router is [chars] 

Explanation    The Standby router for the group has changed.

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-TIMER: Interface [chars] [chars] Grp [dec] [chars] 
timer changed to [dec] [chars] 

Explanation    The hello/hold timer value for the HSRP group has changed

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-5-VIPLEARN: Interface [chars] [chars] Grp [dec] learnt 
virtual ip address [chars] 

Explanation    The local router has learnt virtual ip address from the incoming HSRP packet.

Recommended Action    No action is required.

HSRP_ENGINE-6

Error Message      HSRP_ENGINE-6-STATECHANGE2: [chars] [chars] Grp [dec] state moving 
from [chars] 

Explanation    The router has changed state

Recommended Action    No action is required.

Error Message      HSRP_ENGINE-6-STATECHANGE: [chars] [chars] Grp [dec] state move to 
[chars] 

Explanation    The router has changed state

Recommended Action    No action is required.

IKE Messages

IKE-3

Error Message      IKE-3-CRYPTO_INIT_ERROR: IKEv2 crypto init error: [chars] 

Explanation    Crypto initialization error

Recommended Action    No action is required.

Error Message      IKE-3-ENABLE_ERROR: Unable to store enable flag in configuration 
(error-id [hex]). 

Explanation    Service failed to store the enable flag in configuration. As a result, it will exit

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IKE-3-FIPS_MODE_ERROR: Could not set FIPS mode 

Explanation    The FIPS mode could not be set by IKE

Recommended Action    No action is required.

Error Message      IKE-3-IKE_PROGRAM_EXIT: [chars] 

Explanation    IKE process did an abnormal exit

Recommended Action    No action is required.

Error Message      IKE-3-MAX_HALF_CONN_LIMIT_REACHED: IKEv1 : Exceeded the limit for 
number of half open Phase 1 connections 

Explanation    The number of half open connections has exceeded the maximum limit

Recommended Action    No action is required.

Error Message      IKE-3-PHASE1_NEGOTIATION_FAILED: IKEv1: Phase 1 negotiation failed 
for peer [chars] 

Explanation    IKE policy negotiation failed for peer [chars].

Recommended Action    No action is required.

Error Message      IKE-3-PHASE1_PROPOSAL_MISMATCH: IKEv1: No matching phase 1 proposal 
found for peer [chars] 

Explanation    There is a IKE policy mismatch for the peer.

Recommended Action    No action is required.

Error Message      IKE-3-PHASE2_NEGOTIATION_FAILED: IKEv1: Phase 2 negotiation failed 
for peer [chars] 

Explanation    IPsec policy negotiation failed for peer [chars].

Recommended Action    No action is required.

Error Message      IKE-3-PHASE2_PROPOSAL_MISMATCH: IKEv1: No matching phase 2 proposal 
found for peer [chars] 

Explanation    There is a IPsec policy mismatch for the peer.

Recommended Action    No action is required.

Error Message      IKE-3-UNSUPPORTED_EXCHANGE: IKEv1: Unsupported exchange [dec] 
received from [chars] 

Explanation    A unsupported IKE exchange type [digits] was received from [chars]

Recommended Action    No action is required.

IKE-4

Error Message      IKE-4-INVALID_PAYLOAD_APPEAR: IKEv2 received message (from [chars]) 
with payload ([chars]) appeared in [chars]([chars]) 

Explanation    Received a payload in an inappropriate exchange

Recommended Action    No action is required.

Error Message      IKE-4-MESSAGE_ERROR: IKEv2 message (from [chars]) message error: 
[chars] 

Explanation    Received a malformed message which doesntadheretotheprotocol'

Recommended Action    No action is required.

Error Message      IKE-4-PARSING_ERROR: IKEv2 message (from [chars]) parsing error: 
[chars] 

Explanation    Received a malformed message which can not be parsed appropriately

Recommended Action    No action is required.

Error Message      IKE-4-UNKNOWN_PAYLOAD: IKEv2 received message (from [chars]) with 
un-recognized payload ([chars]) 

Explanation    Received an invalid payload

Recommended Action    No action is required.

Error Message      IKE-4-UNSUPPORT: [chars] is not supported (message from [chars]) 

Explanation    Received something unsupported

Recommended Action    No action is required.

IKE-6

Error Message      IKE-6-POLL_START_DONE: IKE is exiting since it is not enabled 

Explanation    IKE is exiting since it is not enabled in the configuration

Recommended Action    No action is required.

Error Message      ILC-SPAN-3-ERROR: [chars] 

Explanation    Ilc_span_mgr encountered an error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

ILC_HELPER Messages

ILC_HELPER-2

Error Message      ILC_HELPER-2-NO_LICENSE_REBOOT: Linecard [dec] will reboot now. 

Explanation    SSE License has expired, hence the linecard will be rebooted.

Recommended Action    Install appropriate SSE license to be able to use SSM features normally

ILC_HELPER-3

Error Message      ILC_HELPER-3-INVALID_SSI: [chars] 

Explanation    The ssi boot variable is configured to an invalid image. So, the linecard will be bought online in basic mode instead of advanced SSI mode

Recommended Action    Configure a proper image for the ssi boot variable

ILC_HELPER-6

Error Message      ILC_HELPER-6-LICENSE_VALID: A valid license for linecard [dec] has 
been obtained 

Explanation    A valid license has been obtained for the SSM

Recommended Action    No action is required.

Error Message      ILC_HELPER-6-UPGRADE_DELAY: The SSI upgrade on slot [dec] is delayed 
by [dec] secs. 

Explanation    The SSI upgrade is delayed due to the configured ssm upgrade delay command

Recommended Action    No action is required.

IMAGE_DNLD Messages

IMAGE_DNLD-SLOT#-2

Error Message      IMAGE_DNLD-SLOT#-2-ADDON_IMG_DNLD_FAILED: Module image download 
process failed. [chars] 

Explanation    Addon image download to module failed. This module is not operational until an addon image has been successfully installed.

Recommended Action    Verify the location and version of your module image. Use the install module cli command to download a new module image.

Error Message      IMAGE_DNLD-SLOT#-2-IMG_DNLD_COMPLETE: Module image download process. 
[chars] 

Explanation    Image download completed. Module image is being installed.

Recommended Action    No action is required.

Error Message      IMAGE_DNLD-SLOT#-2-IMG_DNLD_FAILED: Module image download process. 
[chars] 

Explanation    Image download failed. Module may be inoperable.

Recommended Action    Use show module cli command to verify the state of this module. Retry image download with install module cli command.

Error Message      IMAGE_DNLD-SLOT#-2-IMG_DNLD_FILE_SYSTEM_CHECK_ERROR: File System 
check failed: [chars] 

Explanation    File system consistency check failed

Recommended Action    File-system repair is needed using fsck

Error Message      IMAGE_DNLD-SLOT#-2-IMG_DNLD_STARTED: Module image download process. 
[chars] 

Explanation    Image download started. Module image downloads are non-disruptive to module operation.

Recommended Action    No action is required.

IMAGE_DNLD-SLOT#-4

Error Message      IMAGE_DNLD-SLOT#-4-IMG_DNLD_FILE_SYSTEM_RECREATION: [chars]. 
Partition was erased and successfully recreated. 

Explanation    File system checking and recreation if necessary for /images.

Recommended Action    No action is required.

IMAGE_DNLD-SLOT#-5

Error Message      IMAGE_DNLD-SLOT#-5-ADDON_IMG_DNLD_COMPLETE: Addon module image 
download process completed. [chars] 

Explanation    Addon image download to module has completed.The module should now be installing this new image.

Recommended Action    This message is informational only.

Error Message      IMAGE_DNLD-SLOT#-5-ADDON_IMG_DNLD_STARTED: Addon module image 
download process started. [chars] 

Explanation    Addon image download to module has started. This is a disruptive download and this module will be inoperable until this download process is complete.

Recommended Action    This message is informational only.

Error Message      IMAGE_DNLD-SLOT#-5-ADDON_IMG_DNLD_SUCCESSFUL: Addon module image 
download and install process successful. [chars] 

Explanation    Addon image download and install to module is successful.

Recommended Action    Use the show module cli command to verify the modulesoperationalstatus.'

IMAGE_UPGRADE Messages

IMAGE_UPGRADE-SLOT#-2

Error Message      IMAGE_UPGRADE-SLOT#-2-IMAGE_UPGRADE_ERROR: [chars] 

Explanation    Image Upgrade Error

Recommended Action    No action is required.

IMAGE_UPGRADE-SLOT#-4

Error Message      IMAGE_UPGRADE-SLOT#-4-IMAGE_UPGRADE_INFO: [chars] 

Explanation    Image Upgrade Info

Recommended Action    No action is required.

IM Messages

IM-3

Error Message      IM-3-IM_IF_FEATURE_BIND_FAILURE: Interface feature bind failed 
[chars] 

Explanation    Interface feature bind failed, so applications in that feature set may not behave correctly.

Recommended Action    No action is required.

Error Message      IM-3-IM_LC_OFFLINE_ERROR: LC Offline could not be sent to vdc:[dec] 

Explanation    LC Offline was not relayed to some vdc, so applications may not behave correctly.

Recommended Action    No action is required.

Error Message      IM-3-IM_RESP_ERROR: Component [chars] opcode:[chars] in vdc:[dec] 
returned error:[chars] 

Explanation    Some component returned an error.

Recommended Action    No action is required.

Error Message      IM-3-IM_SEQ_ERROR: Error ([chars]) while communicating with 
component [chars] opcode:[chars] (for:[chars]) 

Explanation    Some component did not respond to a request in stipulated time.

Recommended Action    No action is required.

IM-5

Error Message      IM-5-IM_DEMUX_ERROR: [chars] 

Explanation    Demux function returned error

Recommended Action    No action is required.

Error Message      IM-5-IM_INTERNAL_ERROR: [chars] 

Explanation    Internal error occurred

Recommended Action    No action is required.

Error Message      IM-5-IM_INTF_STATE: [chars] [chars] in vdc [dec] 

Explanation    Management interface state changed.

Recommended Action    No action is required.

Error Message      IM-5-IM_UNKNOWN_INTERFACE: [chars] 

Explanation    Interface is not supported or not found

Recommended Action    No action is required.

INTERFACE_VLAN Messages

INTERFACE_VLAN-4

Error Message      INTERFACE_VLAN-4-SVI_VLAN_DOES_NOT_EXIST: Vlan [dec] does not exist 

Explanation    Vlan not created before assignment

Recommended Action    Interface-vlan

Error Message      INTERFACE_VLAN-4-SVI_WARN_SVI_UP_IN_NON_ROUTABLE_VDC: Interface 
VLAN [dec] is being kept up in non-routable VDC. Reason: management configuration 
enabled. Please disable all the routing protocols 

Explanation    Keeping Interface VLAN up in non-routable VDC may cause potenital traffic blackhole

Recommended Action    No action is required.

INTERFACE_VLAN-5

Error Message      INTERFACE_VLAN-5-IF_DOWN_ADMIN_DOWN: Interface [chars] is 
down(Administratively Down) 

Explanation    Interface has been configured to be administratively down

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-IF_DOWN_ERROR_DISABLED: Interface [chars] is down. 
Reason [dec] 

Explanation    The interface encountered an error while configuring it

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-IF_DOWN_INACTIVE: Interface [chars] is down 
(Inactive) 

Explanation    Interface VLAN has been suspended or deleted

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_DISABLED: SVI Disabled 

Explanation    SVI Service Disabled

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_ENABLED: SVI Enabled 

Explanation    SVI Service Enabled

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_GET_MAC_FAILED: Failed to acquire MAC address 
for SVI [hex] 

Explanation    SVI failed to acquire MAC address

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_INIT: SVI intialization failed with error [hex] 

Explanation    SVI initialziation error

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_IOD_RELEASE_ERROR_RESPONSE: IM failed to 
release SVI IOD error [hex] 

Explanation    IM failed to release SVI IOD

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_MTS_SEND_FAILURE: MTS send failure for opcode 
[dec], error [hex] 

Explanation    SVI encountered an error in with MTS message

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_MTS_TIME_OUT: MTS send timed out 

Explanation    SVI did not recieve response for mts message

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_RSRVD_VLAN_FAILED: Failed to get list of 
reserved vlans [hex] 

Explanation    SVI failed to get the list reserved vlans

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_SDB_UPDATE_FAILED: sdb update failed with 
ret_val [dec] 

Explanation    SDB updated failed for SVI

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-SVI_SEC_VLAN_FAILED: Failed to get list of 
secondary vlans [hex] 

Explanation    SVI failed to get the list of secondary vlans

Recommended Action    No action is required.

Error Message      INTERFACE_VLAN-5-UPDOWN: Line Protocol on Interface [chars], changed 
state to [chars] 

Explanation    Line protocol status changed for an interface

Recommended Action    No action is required.

IOA_LC Messages

IOA_LC-5

Error Message      IOA_LC-5-IOA_DISABLED: IOA Disabled 

Explanation    IOA Service Disabled

Recommended Action    No action is required.

Error Message      IOA_LC-5-IOA_ENABLED: IOA Enabled 

Explanation    IOA Service nabled

Recommended Action    No action is required.

IPACL Messages

IPACL-0

Error Message      IPACL-0-EMERG: [chars] 

Explanation    Ipacl caused a system failure

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPACL-1

Error Message      IPACL-1-ALERT: [chars] 

Explanation    Ipacl caused failures in other services

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPACL-2

Error Message      IPACL-2-CRIT: [chars] 

Explanation    Ipacl encountered a catastrophic error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPACL-3

Error Message      IPACL-3-ERR: [chars] 

Explanation    Ipacl encountered an error

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPACL-4

Error Message      IPACL-4-WARN: [chars] 

Explanation    Ipacl ignored the unexpected condition

Recommended Action    Please perform debugipaclall',thenrecreatetheoperationscenario,tofindoutmoredetails.'

IPACL-5

Error Message      IPACL-5-NOTE: [chars] 

Explanation    Ipacl does not support this operation

Recommended Action    Please perform debugipaclall',thenrecreatetheoperationscenario,tofindoutmoredetails.'

IPACL-6

Error Message      IPACL-6-INFO: [chars] 

Explanation    Ipacl event occurred

Recommended Action    No action is required.

IPFC Messages

IPFC-2

Error Message      IPFC-2-ALLOC_MEMORY: Memory allocation failed 

Explanation    The service failed to allocate a block of dynamic memory.

Recommended Action    No action is required.

IPFC-3

Error Message      IPFC-3-INIT_FAILED: Initialization failed. Component [chars] 

Explanation    The service failed to start. The failure occurred while initializing the component [chars].

Recommended Action    Show processes to check the status of the other processes, debug the specified component.

Error Message      IPFC-3-IOCTL_FAILED: IOCTL failed 

Explanation    An IOCTL to the character device failed.

Recommended Action    Show IPFC internal interface VSAN <number

Error Message      IPFC-3-PSSERROR: [chars] 

Explanation    IPFC manager encountered a PSS error.

Recommended Action    No action is required.

IPFC-5

Error Message      IPFC-5-CONFIG_EVENT: VSAN interface [dec] [chars] 

Explanation    The specified VSAN Interface has been successfully [chars].

Recommended Action    No action is required.

Error Message      IPFC-5-STATE_CHANGE: VSAN interface [dec] [chars] 

Explanation    The specified VSAN Interface is [chars].

Recommended Action    No action is required.

IPFC-6

Error Message      IPFC-6-STARTING: IP Over Fiber Channel service started 

Explanation    The service has successfully started.

Recommended Action    No action is required.

IPPOOL Messages

IPPOOL-3

Error Message      IPPOOL-3-NO_VC_CONNECTIVITY: Please check if you are connected to 
Management Server 

Explanation    Please check if you are connected to Management Server

Recommended Action    No action is required.

IPPOOL-5

Error Message      IPPOOL-5-IPPOOL_DISABLED: IPPOOL Disabled 

Explanation    IPPOOL Service Disabled

Recommended Action    No action is required.

Error Message      IPPOOL-5-IPPOOL_ENABLED: IPPOOL Enabled 

Explanation    IPPOOL Service enabled

Recommended Action    No action is required.

Error Message      IPPOOL-5-VMKNIC_CREATED: Vmknic Created for module [dec] 

Explanation    Vmknic created

Recommended Action    No action is required.

Error Message      IPPOOL-5-VMKNIC_DELETED: Vmknic Deleted for module [dec] 

Explanation    Vmknic deleted

Recommended Action    No action is required.

Error Message      IPPOOL-5-VMKNIC_UPDATED: Vmknic updated for module [dec] 

Explanation    Vmknic updated

Recommended Action    No action is required.

IPQOSMGR Messages

IPQOSMGR-2

Error Message      IPQOSMGR-2-QOSMGR_DCBXP_PFC_CMP_FAIL_MSG: [chars] - qos config 
[chars] not compatible with the peer 

Explanation    Port_id [chars] has qos config [chars] which is incompatible with the peer.

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_HA_FAILURE: Failed to do high availability 
operation: [chars]. 

Explanation    Failed to do high availability operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_INIT_FAILED: Initialization failed for QoS 
Manager: [chars], reason: [hex]. 

Explanation    Initialization failed for QoS Manager due to [chars], reason: [hex].

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_MTS_FAILURE: Failed to do MTS operation: [chars]. 

Explanation    Failed to do MTS operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_MTS_REGISTRATION_FAILED: MTS options setting to 
[hex] failed for opCode: [dec]. 

Explanation    MTS options setting to [hex] failed for opCode: [dec].

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_NETWORK_QOS_POLICY_CHANGE: Policy [chars] is now 
active 

Explanation    [chars] is the new active network-qos policy

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_PSS_FAILURE: Failed to do PSS operation: [chars], 
reason: [hex]. 

Explanation    Failed to do PSS operation [chars]. [hex] is the reason.

Recommended Action    No action is required.

Error Message      IPQOSMGR-2-QOSMGR_PSS_VER_FAIL: PSS file [chars] has version 
[dec].[dec].[dec], expected version [dec].[dec].[dec]. 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version.

Recommended Action    No action is required.

IPQOSMGR-3

Error Message      IPQOSMGR-3-QOSMGR_CONFIG_ERROR: Configuration error: [chars]. 

Explanation    Configuration error. [chars] is the reason.

Recommended Action    No action is required.

Error Message      IPQOSMGR-3-QOSMGR_NVDC_PFF_ERROR: PPF verify/commit failed in vdc 
[dec] error: [hex] for global qos command 

Explanation    For global qos command, PPF verify/commit failed in vdc [dec] with reason [hex].

Recommended Action    No action is required.

Error Message      IPQOSMGR-3-QOSMGR_PPF_ERROR: PPF library error: [chars]. 

Explanation    PPF library errors. [chars] is the reason.

Recommended Action    No action is required.

IPQOSMGR-4

Error Message      IPQOSMGR-4-QOSMGR_LC_ERROR_MSG: Linecard [dec] returned an error: 
[chars] 

Explanation    Linecard [dec] returned an error message which is reported as [chars].

Recommended Action    No action is required.

Error Message      IPQOSMGR-4-QOSMGR_POLICIES_PRESENT_ON_DELETED_VLANS: Some VLANs (id: 
[chars]) which are getting deleted now are still having qos service-policy 
attached. These policies will be effective only when the VLANs get created again. 

Explanation    VLAN(s) [chars] is(are) getting deleted now. This is an informationsl message to notify that qos service-policies are present when the vlan is deleted. If the service-policies are not needed, please detach them from the vlans

Recommended Action    No action is required.

Error Message      IPQOSMGR-4-QOSMGR_PPF_WARNING: PPF library warning: [chars]. 

Explanation    PPF library warning. [chars] is the reason.

Recommended Action    No action is required.

Error Message      IPQOSMGR-4-QOSMGR_WARNING_MSG: [chars] [dec] 

Explanation    QOSMGR warning messages is reported as [chars] [dec].

Recommended Action    No action is required.

IPQOSMGR-5

Error Message      IPQOSMGR-5-QOSMGR_LC_STAT_SESSION_ERROR_MSG: Linecard [dec] returned 
the following error for [chars] session: [chars]. 

Explanation    Linecard [dec] returned an error message for session of type [chars] which is reported as [chars]. This message may be seen during linecard reload if there is an active session going on.

Recommended Action    No action is required.

IPQOSMGR-6

Error Message      IPQOSMGR-6-QOSMGR_DCBXP_CMP_FAIL_MSG: [chars] - qos config [chars] 
not compatible with the peer 

Explanation    Dcbxp warning: Port_id [chars] has qos config [chars] which is incompatible with the peer.

Recommended Action    No action is required.

Error Message      IPQOSMGR-6-QOSMGR_STATUS: QOSMGR Status: [chars]. 

Explanation    QOSMGR status is reported as [chars].

Recommended Action    No action is required.

IPQOSMGR-SLOT#-3

Error Message      IPQOSMGR-SLOT#-3-QOSMGR_DPA_MSG: DPA returned error message - 
[chars] 

Explanation    An error occured in the DPA [string] is the error message.

Recommended Action    No action is required.

IPSEC Messages

IPSEC-2

Error Message      IPSEC-2-IPSEC_INIT: IPSec initialization of [chars] [chars] 

Explanation    IPSec initialization failed

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPSEC-2-IPSEC_SPD_OVERFLOW_DUE_TO_ACL: SPD Overflow on interface due 
to IP ACL [chars] bound to crypto map [chars] [dec] 

Explanation    Modifying IP ACL caused Security Policy Database on the interface to overflow, IP ACL filter not applied to security policy database

Recommended Action    Undo IP ACL change

IPSEC-3

Error Message      IPSEC-3-14_2_MODULE_PACKETS_DROPPED: [chars]: packets were dropped 
in the module 

Explanation    Packets dropped in the 14/2 module. Please collect drop statistics using show ipsec internal crypto-acc interface gigabit <slot/port

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPSEC-3-IPSEC_FIPS_TEST_FAILED: IPSEC FIPS compliance test failed 

Explanation    IPSEC FIPS compliance test failed

Recommended Action    No action is required.

Error Message      IPSEC-3-IPSEC_MSG_SEND_FAILURE: failed to send [chars] to sap [dec]: 
[chars] 

Explanation    Failed to send a message

Recommended Action    No action is required.

IPSEC-5

Error Message      IPSEC-5-IPSEC_CMS_IF_ACL_UPDATED: IP ACL [chars] updated while 
Crypto map [chars] [dec] bound to interface(s) 

Explanation    IP ACL updated while it is mapped to a crypto map that is bound to interface(s)

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_DISABLED_LIC_EXPIRED: IPSec Disabled due to License 
Expiry 

Explanation    IPSec Disabled due to License Expiry

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_DISABLED: IPSec Disabled 

Explanation    IPSec Disabled

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_ENABLED: IPSec Enabled 

Explanation    IPSec Enabled

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_SA_CREATED: [chars]: IPSec SA created: local_ip: 
[chars], peer_ip: [chars], [chars] SPI: [dec] ([hex]) 

Explanation    IPSec SA created

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_SA_DELETED: [chars]: IPSec SA deleted: local_ip: 
[chars], peer_ip: [chars], [chars] SPI: [dec] ([hex]), reason: [chars] 

Explanation    IPSec SA deleted

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_SA_REKEYED: [chars]: IPSec SA rekeyed: local_ip: 
[chars], peer_ip: [chars], [chars] SPI: [dec] ([hex]) 

Explanation    IPSec SA rekeyed

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_TUNNEL_CREATED: [chars]: IPSec tunnel created: 
local_ip: [chars], peer_ip: [chars], id: [dec], protocol: [chars], traffic:: 
local: [chars]/[chars], port: [chars], remote: [chars]/[chars], ports: [chars] 

Explanation    IPSec tunnel created

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_TUNNEL_DELETED: [chars]: IPSec tunnel deleted: 
local_ip: [chars], peer_ip: [chars], id: [dec], protocol: [chars], traffic:: 
local: [chars]/[chars], ports: [chars] remote: [chars]/[chars], ports: [chars] 

Explanation    IPSec tunnel deleted

Recommended Action    No action is required.

Error Message      IPSEC-5-IPSEC_TUNNEL_REKEYED: [chars]: IPSec tunnel rekeyed: 
local_ip: [chars], peer_ip: [chars], id: [dec], protocol: [chars] traffic:: local: 
[chars]/[chars], ports: [chars] remote: [chars]/[chars], ports: [chars] 

Explanation    IPSec tunnel rekeyed

Recommended Action    No action is required.

IPS_SB_MGR Messages

IPS_SB_MGR-SLOT#-2

Error Message      IPS_SB_MGR-SLOT#-2-NODE_CORE_NOT_RESPONDING: [Node [dec], Core 
[dec]]: Not responding to heartbeats, state=[hex] 

Explanation    Node is not incrementing heartbeats periodically

Recommended Action    Potential node software issue. Please contact your support representative

Error Message      IPS_SB_MGR-SLOT#-2-NODE_NOT_RESPONDING: [Node [dec], Core [dec]] : 
Not responding to heartbeats 

Explanation    Node manager is not receiving heartbeat responses from the node

Recommended Action    Potential node software issue. Please contact your support representative

Error Message      IPS_SB_MGR-SLOT#-2-NODE_REIMAGE_PREPARE_FAIL: [Node [dec]]: Disk 
formatting failed during node install 

Explanation    There was a problem during the partitioning of disk and creation of file systems during node install.

Recommended Action    Potential node software issue. Please contact your support representative

Error Message      IPS_SB_MGR-SLOT#-2-PORT_SOFTWARE_FAILURE: Port software failure, 
module [dec] port [dec] 

Explanation    The software servicing the data path on the port has failed

Recommended Action    No action is required.

IPS_SB_MGR-SLOT#-3

Error Message      IPS_SB_MGR-SLOT#-3-COMP_FAILURE: Heartbeat failure in compression 
engine (error [hex]) 

Explanation    The compression engine did not respond to heartbeats, due to some failure. SAN-OS will restart the compression engine to clear the problem.

Recommended Action    No action is required.

Error Message      IPS_SB_MGR-SLOT#-3-CRYPTO_FAILURE: Heartbeat failure in encryption 
engine (error [hex]) 

Explanation    The encryption engine did not respond to heartbeats, due to some failure. SAN-OS will restart the encryption engine to clear the problem.

Recommended Action    No action is required.

Error Message      IPS_SB_MGR-SLOT#-3-FIPS_SELF_TEST_FAILURE: [chars] Restarting the 
octeon... 

Explanation    FIPS self test failed for the algorithm. Restarting the octeon.

Recommended Action    No action is required.

IPS_SB_MGR-SLOT#-4

Error Message      IPS_SB_MGR-SLOT#-4-NODE_NOT_COMPAT_WITH_ADD_ON: svc-node[dec] image 
is not compatible with svclc image 

Explanation    The svc image on the node is not compatible with the add on image running on the linecard.

Recommended Action    Please contact your support representative

Error Message      IPS_SB_MGR-SLOT#-4-NODE_NOT_COMPAT_WITH_CURRENT: svc-node[dec] 
image is not compatible with current node image 

Explanation    The new svc image is not compatible with the svc image currently running on the node

Recommended Action    Please contact your support representative

Error Message      IPS_SB_MGR-SLOT#-4-NODE_NOT_COMPAT_WITH_SUP: svc-node[dec] image is 
not compatible with system image 

Explanation    The svc image on the node is not compatible with the supervisor image.

Recommended Action    Please contact your support representative

IPS_SB_MGR-SLOT#-6

Error Message      IPS_SB_MGR-SLOT#-6-SBMGR_EVENT: Sbmgr event: [chars] 

Explanation    This is an event log of sb_mgr relating to a port/node

Recommended Action    No action is required.

IPS Messages

IPS-2

Error Message      IPS-2-ISCSI_IPS_INIT: IPS initialization of [chars] [chars] 

Explanation    IPS initialization failed

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPS-3

Error Message      IPS-3-FCIP_FTA_ACCEL_CHAIN_ABORTED: Exch Aborted FC oxid [hex] My 
oxid [hex] State [chars] Event [chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] 
CUI: [hex] DA [hex] VSAN: [dec] (Internal [hex]:[hex]) 

Explanation    FTA Exch being aborted

Recommended Action    Informational no action required

Error Message      IPS-3-FCIP_FTA_DATA_SENSE: Sense data with ERA [hex] sent to CH FCID: 
[hex] CHI: [hex] from FCIP CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    Sense data with ERA sent

Recommended Action    SYSLOGDOC_CONTACT_TAC

Error Message      IPS-3-FCIP_FTA_ERA_35: ERA 0x35 presented to CH FCID: [hex] CHI: 
[hex] from FCIP CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP got an ERA 35

Recommended Action    SYSLOGDOC_CONTACT_TAC

Error Message      IPS-3-FCIP_FTA_ERA_38: ERA 0x38 received CH FCID: [hex] CHI: [hex] 
from FCIP CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] at tape capacity: [dec] MB 

Explanation    FCIP got an ERA 38

Recommended Action    SYSLOGDOC_CONTACT_TAC

Error Message      IPS-3-FCIP_FTA_LOCATE_RBID_MISMATCH: Permanent Error due to Locate 
RBID Mismatch, CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: 
[dec] 

Explanation    FCIP-FTA got a Permanent Error

Recommended Action    Informational no action required

Error Message      IPS-3-FCIP_FTA_PERM_ERR: Permanent Error, ERA [hex] rcvd CH FCID: 
[hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] sense_byte[2,6]: 
[[hex], [hex]] 

Explanation    FCIP-FTA got a Permanent Error

Recommended Action    Informational no action required

Error Message      IPS-3-FCIP_FTA_RETRY_ERROR: [chars] retries [dec] FC oxid [hex] My 
oxid [hex] State [chars] Event [chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] 
CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FTA Command timed out

Recommended Action    Informational no action required

Error Message      IPS-3-IPS_CRYPTO_FIPS_FAILED: IPS module [dec] has failed FIPS tests. 
FIPS info - [chars] 

Explanation    FIPS error occurred in the IPS module.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-IPS_EGRESS_PERR: Parity error on dma-bridge egress. Count: 
[dec] 

Explanation    Parity error occured in dma-bridge egress direction.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-IPS_FIPS_MODE_ERROR: IPS FIPS error: [chars] 

Explanation    IPS module FIPS mode error

Recommended Action    No action is required.

Error Message      IPS-3-IPS_FIPS_TEST_FAILED: IPS FIPS compliance test failed 

Explanation    IPS FIPS compliance test failed

Recommended Action    No action is required.

Error Message      IPS-3-IPS_INGRESS_PERR: Parity error on dma-bridge ingress. Count: 
[dec] 

Explanation    Parity error occured in dma-bridge ingress direction.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_CLEAR_FAILED: [chars] 

Explanation    An error occurred while clearing the CFS lock. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_COMMIT_FAILED: [chars]; [chars] 

Explanation    An error occurred while commiting the cfs config data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_CONFIG_FAILED: [chars]; [chars] 

Explanation    An error occurred while distributing the CFS config data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_LOCK_FAILED: [chars] 

Explanation    An error occurred while acquiring the CFS lock. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_ACTIVATION_FAILED: [chars]; [chars] 

Explanation    An error occurred while activating merged configuration. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_CLEARED: [chars] 

Explanation    Merge cleared, reason: [chars]

Recommended Action    No action is required.

Error Message      IPS-3-ISLB_CFS_MERGE_COMMIT_FAILED: [chars]; [chars] 

Explanation    An error occurred while commiting the cfs merge config data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_CONFIG_FAILED: [chars]; [chars] 

Explanation    An error occurred while distributing the CFS merge config data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_FAILED: [chars]; [chars] 

Explanation    An error occurred while merging the iSLB CFS fabrics. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_PRECOMMIT_FAILED: [chars]; [chars] 

Explanation    An error occurred while precommiting merge data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_MERGE_REQ_REJECTED: [chars] 

Explanation    Merge requested rejected, reason: [chars]

Recommended Action    No action is required.

Error Message      IPS-3-ISLB_CFS_MERGING_CONFIG_DB_FAILED: [chars]; [chars] 

Explanation    An error occurred while merging the config data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_PRECOMMIT_FAILED: [chars]; [chars] 

Explanation    An error occurred while precommiting data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_PWWN_RESV_CLAIM_FAILED: [chars] 

Explanation    PWWN reservation claim failed. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_PWWN_RESV_RELEASE_FAILED: [chars] 

Explanation    PWWN reservation release failed. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_UNLOCK_FAILED: [chars] 

Explanation    An error occurred while releasing the CFS lock. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_CFS_VRRP_DIST_FAILED: [chars] 

Explanation    An error occurred while distributing the VRRP CFS runtime data. The reason for the failure : [chars]

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_ZONE_ACTIVATION_FAILED: iSLB zoneset activation returned 
[hex] for VSAN [dec] 

Explanation    ISLB zoneset activation failed.

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      IPS-3-ISLB_ZONE_ACTIVATION_RETRY: iSLB zoneset activation returned 
[hex] for VSAN [dec] 

Explanation    ISLB zoneset activation failed. Zone server busy.

Recommended Action    Retry the iSLB zonest activation.

Error Message      IPS-3-ISLB_ZONE_NO_ACTIVE_ZONESET: iSLB zoneset activation returned 
[hex] for VSAN [dec] 

Explanation    ISLB zoneset activation failed. No active zoneset.

Recommended Action    Activate a zoneset in the specified VSAN and retry

Error Message      IPS-3-RED_PACKET_DROPS: Congestion detected on GigabitEthernet port 
(buffer pool size: [dec]) 

Explanation    Congestion detected on GigabitEthernet port due to RED threshold limit

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IPS-4

Error Message      IPS-4-FCIP_FTA_CFG_MISMATCH: [chars]: Mismatch in FCIP Ficon Tape 
Acceleration configuration with peer 

Explanation    The FCIP Ficon Tape Acceleration configuration does not match with peersconfiguration'

Recommended Action    Fix the FCIP Ficon Tape Acceleration configuration to be consistent with the peer

Error Message      IPS-4-FCIP_FTA_VSAN_UPDATE_WARNING: FCIP FICON tape acceleration 
VSAN update had an error ([chars]) on interface [chars] causing a flap of the 
interface 

Explanation    The FCIP FICON tape acceleration VSAN configuration experienced an error when disabling and enabling the VSAN over the FCIP tunnel. The FCIP tunnel was disabled and re-enabled as a result of this error to ensure data integrity.

Recommended Action    No action is required.

Error Message      IPS-4-FCIP_LICENSE_BIND_FAILED: Bind failed for [chars] due to 
[chars] for license failure; configuration accepted but bind failed 

Explanation    The FCIP configuration was accepted, but the FCIP interface did not bind to a physical interface because the appropriate license was not available. If a license becomes available in the future, this FCIP interface will bind to a physical interface automatically.

Recommended Action    Check the license state with "show license usage" and acquire the necessary FCIP license

Error Message      IPS-4-FCIP_XRCE_LICENSE_FAILED: XRC Acceleration deactivated due to 
license failure 

Explanation    The XRC Acceleration configuration was accepted, but will remain inactive until a valid license is available. When the appropriate license is installed, XRC accelaration will be activated.

Recommended Action    Check the license state with "show license usage" and acquire the necessary XRC_ACCL license

Error Message      IPS-4-FCIP_XRCE_LICENSE_INSTALLED: XRC Acceleration activated due to 
valid license 

Explanation    The XRC Acceleration configuration is activated as a valid license has been installed.

Recommended Action    No action is required.

IPS-5

Error Message      IPS-5-FCIP_BIND_FAILED: Bind failed for [chars] due to [chars] for 
[chars] 

Explanation    FCIP/ISCSI Interface bind to Ethernet port failed

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_BPORT_KEEPALIVES_NOT_SUPPORTED: Bport Keepalives not 
supported for FCIP [chars] 

Explanation    Bport Keepalives not supported in this release

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_BPORT_NOT_SUPPORTED: Bport not supported for FCIP [chars] 

Explanation    Bport not supported in this releas

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_ALREADY_OFF: FTA Already Off, [chars] VSAN: [dec] 

Explanation    FTA Already Off

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_ALREADY_ON: FTA Already ON, [chars] VSAN: [dec] 

Explanation    FTA Already ON

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_CB_DOWN: FTA [chars] is DOWN 

Explanation    FTA is DOWN

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_CB_UP: FTA [chars], is UP 

Explanation    FTA is UP

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_DISBAND_GRP_CMD: Disband Group message processed 
PGID: [chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: 
[dec] 

Explanation    FCIP Disbanded a Group

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_EST_GRP_CMD: Path Group establised for PGID: [chars] 
CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP established a Path Group

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_NPORT_PATH_RSCN_CLNUP_PASS1: RSCN Cleanup Pass1 
[chars] FCID1: [hex] FCID2: [hex] VSAN: [dec] 

Explanation    Doing RSCN Cleanup, Pass 1

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_NPORT_PATH_RSCN_CLNUP_PASS2: RSCN Cleanup Pass2 
[chars] FCID1: [hex] FCID2: [hex] VSAN: [dec] 

Explanation    Doing RSCN Cleanup, Pass 2

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_RESIGN_GRP_CMD: Resign group processed for PGID: 
[chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP Resigned a Group

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_RESP_3490: 3490 device discovered by FCIP CH FCID: 
[hex] CHI: [hex] device at CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    Device type discovered is 3490

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_RESP_3590: 3590 device discovered by FCIP CH FCID: 
[hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    Device type discovered is 3590

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_RESP_NOT_TAPE: Non-tape device discovered by FCIP CH 
FCID: [hex] CHI: [hex] device at CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP discovered a non-tape device

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_TURN_OFF_LAST_VSAN: FTA turned off for the Last VSAN, 
[chars] VSAN: [dec] 

Explanation    FTA turned off for the Last Vsan

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_TURN_OFF_NONLAST_VSAN: FTA turned off for the 
Non-Last VSAN, [chars] VSAN: [dec] 

Explanation    FTA turned off for the Non-Last Vsan

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_TURN_ON: Turn ON FTA, [chars] VSAN: [dec] 

Explanation    FTA turned ON

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTA_WARNING: FTA Warning :[chars] 

Explanation    Generic FTA Warning

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_FTRA_CFG_MISMATCH: [chars]: Mismatch in FCIP FICON Tape 
Read Accelerator configuration with peer 

Explanation    The FCIP FICON Tape Read Accelerator configuration does not match with peersconfiguration'

Recommended Action    Fix the FCIP FICON Tape Read Accelerator configuration to be consistent with the peer

Error Message      IPS-5-FCIP_IF_CR_DEL: Interface [chars] [chars] 

Explanation    FCIP Interface was Created or Deleted

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_MODE1_CHANGED_TO_MODE2: Changing mode1 compression to 
mode2 for [chars], on a MSM/SSN-16 linecard 

Explanation    Change mode1 compression to mode2 on a MSM/SSN-16 linecard

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_NUM_TCP_CONNS_MISMATCH: [chars]: configured for 2 tcp 
connections but currently operating with 1 connection 

Explanation    Number of configured tcp connections dontmatchnumberofconnectionscurrentlyup'

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_PEER_CAVIUM: Peer FCIP [chars] is a MSM/SSN-16 linecard 

Explanation    Peer linecard is a MSM/SSN-16

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_PEER_NON_CAVIUM: Peer FCIP [chars] is a non MSM/SSN-16 
linecard 

Explanation    Peer linecard is non MSM/SSN-16

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_RA_CFG_MISMATCH: [chars]: Mismatch in FCIP Tape Read 
Acceleration capability with peer 

Explanation    The FCIP Tape Read Acceleration capability does not match with peersconfiguration'

Recommended Action    Fix the FCIP Tape Read Acceleration capability to be consistent with the peer

Error Message      IPS-5-FCIP_SF_NOT_SUPPORTED: Special-Frame not supported for FCIP 
[chars] 

Explanation    Spl-Frame not supported in this release

Recommended Action    Informational no action required

Error Message      IPS-5-FCIP_TA_CFG_MISMATCH: [chars]: Mismatch in FCIP Tape 
Acceleration configuration with peer 

Explanation    The FCIP Tape Acceleration configuration does not match with peersconfiguration'

Recommended Action    Fix the FCIP Tape Acceleration configuration to be consistent with the peer

Error Message      IPS-5-FCIP_TA_ITL_MISMATCH: [chars]: Mismatch in FCIP Write/Tape 
Acceleration software capability with peer 

Explanation    The FCIP Write/Tape Acceleration software capability does not match with peerssoftwarecapability'

Recommended Action    Fix the FCIP software to be consistent with the peer

Error Message      IPS-5-FCIP_TSTAMP_CHK_FAILED: [chars]: Timestamp check failed on 
ingressing frames 

Explanation    Timestamp between local and remote side exceeds the configured tolerance

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_UNBIND_FAILED: UNBIND failed for [chars] due to [chars] 
for [chars] 

Explanation    FCIP/ISCSI Interface UNBIND from Ethernet port failed

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_WA_CFG_MISMATCH: [chars]: Mismatch in FCIP Write 
Acceleration configuration with peer 

Explanation    The FCIP Write Acceleration configuration does not match with peersconfiguration'

Recommended Action    Fix the FCIP Write Acceleration configuration to be consistent with the peer

Error Message      IPS-5-FCIP_WA_XFER_RDY_ERR: [chars]: FCIP Write Acceleration 
received XFER-RDY after exhcange cleanup. Host [hex] Target [hex] 

Explanation    FCIP Write/Tape Acceleration received XFER-RDY after exchange cleanup

Recommended Action    No action is required.

Error Message      IPS-5-FCIP_XRCE_CFG_MISMATCH: [chars]: Mismatch in FCIP XRC Emulator 
configuration with peer 

Explanation    The FCIP XRC Emulator configuration does not match with peersconfiguration'

Recommended Action    Fix the FCIP XRC Emulator configuration to be consistent with the peer

Error Message      IPS-5-IPS_IPACL_LOG_MSG: [chars] 

Explanation    Details of the packet dropped due to ACLs

Recommended Action    No action is required.

Error Message      IPS-5-IPS_MGR_FEATURE_ENABLE: ips:[dec] iscsi:[dec] fcip:[dec] 
iscsi-intf-vsan:[dec] ips-lc:[dec] 

Explanation    IPS Manager feature enabled/disabled

Recommended Action    No action is required.

Error Message      IPS-5-IPS_TCP_PORT_IN_USE: Cannot bringup interface [chars], local 
port already in use 

Explanation    FCIP and iSCSI interface are trying to use the same local port, please use different ports

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_BAD_DATA_DIGEST_CRC: iSCSI ingress data digest error 
from initiator [chars] alias [chars] S_ID [hex] to D_ID [hex] 

Explanation    ISCSI Ingress Data Digest CRC failed

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_CONN_DOWN_BATCH: [chars]: [dec] iSCSI sessions failed in 
last [chars], reason: [chars] 

Explanation    Number of iSCSI session down during the last time interval

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_CONN_DOWN: [chars]: iSCSI session down from initiator 
[chars] alias [chars] ip [chars] to target [chars], reason: [chars] 

Explanation    ISCSI session goes down

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_CONN_UP: [chars]: iSCSI session up from initiator [chars] 
alias [chars] ip [chars] to target [chars] 

Explanation    ISCSI session comes up and reaches Full-Feature phase

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_PORT_FAILOVER: [chars]: iSCSI initiator [chars] alias 
[chars] ip [chars] target [chars]. FC session failed over to port [chars] 

Explanation    FC session for the iSCSI session failed over to newly active port

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_SB_GET_TGT: iSCSI SB get [dec] targets, initiator [chars] 
alias [chars] ip [chars] 

Explanation    ISCSI FCNS query response

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_SESSION_CREATE_FAILURE: [chars]: iSCSI Session initiator 
[chars] target [chars] create failed. [chars] 

Explanation    ISCSI Session Create failed

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_SESSION_CREATE_REDIRECT: [chars]: iSCSI Session 
initiator [chars] target [chars] redirected to [chars]/[chars] 

Explanation    ISCSI Session Create redirected

Recommended Action    No action is required.

Error Message      IPS-5-ISCSI_SESSION_REDIRECT_TIMEOUT: iSCSI Session initiator 
[chars] to [chars] redirected to [chars] timeout 

Explanation    ISCSI Session Redirect timeout

Recommended Action    No action is required.

Error Message      IPS-5-ISLB_CFS_SESSION_CLEARED: CFS Session Cleared 

Explanation    CFS Session Cleared by user

Recommended Action    No action is required.

Error Message      IPS-5-PORT_IPCFG_FAILED: Cannot configure IP address for interface 
[chars] 

Explanation    Cannot configure IPS port IP address

Recommended Action    No action is required.

Error Message      IPS-5-SB_MGR_CORE_FAILED: Ethernet Processing core [chars] failed 
due to [chars] 

Explanation    Ethernet Processing Core failed

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_ENTITY_ID_MISMATCH: [chars]: special frame profile ID 
mismatch 

Explanation    Special frame received and destination profile ID does not match local profile ID

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_FABRIC_WWN_MISMATCH: [chars]: special frame fabric wwn 
mismatch 

Explanation    Special frame received and source/destination fabric wwn does not match local destination/ source fabric wwn

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_IF_ADMIN_DOWN: [chars]: special frame received if down 

Explanation    Special frame received and interface is admin down

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_IF_NOT_ENABLED: [chars]: special frame not enabled 

Explanation    Special frame received and interface special frame configuration is disabled

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_INVALID_NONCE: [chars]: special frame response has 
invalid nonce for FCIP 

Explanation    Special frame response has a different nonce than was originally sent in the special frame

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_NOT_RECV: [chars]: special frame was not received by 
passive-side FCIP 

Explanation    Special frame was not received by the passive-side of the FCIP TCP tunnel within given time period

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_RESP_MISMATCH: [chars]: special frame response has byte 
mismatch for FCIP 

Explanation    Special frame response has a mismiatch in one of the bytes from what was sent from the FCIP special frame sender

Recommended Action    No action is required.

Error Message      IPS-5-SFRAME_RESP_NOT_RECV: [chars]: special frame response was not 
received by active-side FCIP 

Explanation    Special frame response was not received by the active-side of the FCIP TCP tunnel within given time period

Recommended Action    No action is required.

IPS-6

Error Message      IPS-6-FCIP_FTA_READ_ACCEL_STARTED: Read Acceleration started for CH 
FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP-FTA Read Acceleration started

Recommended Action    Informational no action required

Error Message      IPS-6-FCIP_FTA_READ_ACCEL_STOPPED: Read Acceleration stopped for CH 
FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] due to [chars] 
after [dec] MB reads 

Explanation    FCIP-FTA Read Acceleration stopped

Recommended Action    Informational no action required

Error Message      IPS-6-FCIP_FTA_WRITE_ACCEL_STARTED: Write Acceleration started for 
CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] 

Explanation    FCIP-FTA Write Acceleration started

Recommended Action    Informational no action required

Error Message      IPS-6-FCIP_FTA_WRITE_ACCEL_STOPPED: Write Acceleration stopped for 
CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [dec] due to 
[chars] after [dec] MB writes 

Explanation    FCIP-FTA Write Acceleration stopped

Recommended Action    Informational no action required

IPS-7

Error Message      IPS-7-ISCSI_FCNS_QUERY_REQ: return [hex], wait [dec], VSAN [dec], 
Init: [chars] 

Explanation    ISCSI FCNS query

Recommended Action    No action is required.

Error Message      IPS-7-ISCSI_FCNS_QUERY_RESP: result [hex], [dec] targets, wait 
[dec], Init: [chars] 

Explanation    ISCSI FCNS query response

Recommended Action    No action is required.

Error Message      IPS-7-ISCSI_NEW_FCNS_QUERY_REQ: return [hex], VSANs [chars], Init: 
[chars] 

Explanation    ISCSI FCNS query

Recommended Action    No action is required.

Error Message      IPS-7-ISCSI_NEW_FCNS_QUERY_RESP: result [hex], [dec] entries, [dec] 
targets, [dec] total targets Init: [chars] 

Explanation    ISCSI FCNS query response

Recommended Action    No action is required.

Error Message      IPS-7-ISNS_SVR_ERR_RESPONSE: iSNS server returned following error 
code on iSNS request for interface [chars] : [dec] 

Explanation    ISNS server returned an error for register/deregister request. For select error codes iSNS client would retry and re-register all target nodes corresponding to the interface

Recommended Action    No action is required.

IPV6 Messages

IPV6-2

Error Message      IPV6-2-ALLOC_MEMORY: Memory allocation failed 

Explanation    The IP Configuration Manager failed to allocate a block of dynamic memory.

Recommended Action    No action is required.

IPV6-3

Error Message      IPV6-3-FILE_WRITE_FAILED: Writing to file [chars] failed - error: 
[chars] 

Explanation    Writing to a file failed probably due to no space.

Recommended Action    Ipv6

Error Message      IPV6-3-INIT_FAILED: Initialization failed. Component [chars] 

Explanation    The service failed to start. The failure occurred while initializing the component [chars].

Recommended Action    Show processes to check the status of the other processes, debug the specified component.

IPV6-4

Error Message      IPV6-4-DAD_FAILED_EVENT: Duplicate address detection failed for 
[chars] on [chars] 

Explanation    Duplicate address detection for IP address failed.

Recommended Action    Ipv6

IPV6-6

Error Message      IPV6-6-CONFIG_EVENT: IP Configuration Msg: [chars] 

Explanation    Configuration message that needs to be logged.

Recommended Action    No action is required.

Error Message      IPV6-6-INTERFACE_DELETED: The interface [chars] has been deleted 

Explanation    The specified interface has been deleted. The service will delete all the configuration on that interface.

Recommended Action    No action is required.

Error Message      IPV6-6-INTERFACE_EVENT: IP address [chars] [chars] on interface 
[chars] 

Explanation    The IP address [chars] has been successfully [chars] on the interface [chars].

Recommended Action    No action is required.

Error Message      IPV6-6-ROUTE_NOT_ACTIVE: The [chars] is not active 

Explanation    The specified route is successfully configured but currently is not active.

Recommended Action    Check that the route is correct and the outgoing interface is operationally up.

Error Message      IPV6-6-STARTING: IP configuration Manager started 

Explanation    The IP Configuration Manager service has successfully started.

Recommended Action    No action is required.

IP Messages

IP-1

Error Message      IP-1-DHCP_CLIENT_FAILED: dhcp-client failed to get the ip address 

Explanation    Dhcp-client failed to get the ip from server, probably due to server lease unavailability or cable disconnectivity .

Recommended Action    Ip

IP-2

Error Message      IP-2-ALLOC_MEMORY: Memory allocation failed 

Explanation    The IP Configuration Manager failed to allocate a block of dynamic memory.

Recommended Action    No action is required.

IP-3

Error Message      IP-3-FILE_WRITE_FAILED: Writing to file [chars] failed - error: 
[chars] 

Explanation    Writing to a file failed probably due to no space.

Recommended Action    Ip

Error Message      IP-3-INIT_FAILED: Initialization failed. Component [chars] 

Explanation    The service failed to start. The failure occurred while initializing the component [chars].

Recommended Action    Show processes to check the status of the other processes, debug the specified component.

IP-4

Error Message      IP-4-DAD_FAILED_EVENT: Duplicate address detected for [chars] on 
[chars] 

Explanation    Duplicate address detected for IP address.

Recommended Action    Ip

IP-6

Error Message      IP-6-CONFIG_EVENT: IP Configuration Msg: [chars] 

Explanation    Configuration message that needs to be logged.

Recommended Action    No action is required.

Error Message      IP-6-DHCP_CLIENT_SUCCESS: dhcp_client got ip 
address:[chars],netmask:[chars] for mgmt interface,got from server:[chars] 

Explanation    Dhcp-client is able to get the ip address from server,

Recommended Action    No action is required.

Error Message      IP-6-INTERFACE_DELETED: The interface [chars] has been deleted 

Explanation    The specified interface has been deleted. The service will delete all the configuration on that interface.

Recommended Action    No action is required.

Error Message      IP-6-INTERFACE_EVENT: IP address [chars] [chars] on interface [chars] 

Explanation    The IP address [chars] has been successfully [chars] on the interface [chars].

Recommended Action    No action is required.

Error Message      IP-6-ROUTE_NOT_ACTIVE: The [chars] is not active 

Explanation    The specified route is successfully configured but currently is not active.

Recommended Action    Check that the route is correct and the outgoing interface is operationally up.

Error Message      IP-6-STARTING: IP configuration Manager started 

Explanation    The IP Configuration Manager service has successfully started.

Recommended Action    No action is required.

ISAPI Messages

ISAPI-SLOT#-0

Error Message      ISAPI-SLOT#-0-INVISTA_EMERG: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-0-MSM_EMERG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-0-NSP_EMERG: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-0-SSM_EMERG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-0-SSN_EMERG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-1

Error Message      ISAPI-SLOT#-1-INVISTA_ALERT: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-1-MSM_ALERT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-1-NSP_ALERT: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-1-SSM_ALERT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-1-SSN_ALERT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-2

Error Message      ISAPI-SLOT#-2-INVISTA_CRIT: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-2-MSM_CRIT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-2-NSP_CRIT: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-2-SSM_CRIT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-2-SSN_CRIT: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-3

Error Message      ISAPI-SLOT#-3-INVISTA_ERROR: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-3-MSM_ERROR: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-3-NSP_ERROR: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-3-SSM_ERROR: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-3-SSN_ERROR: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-4

Error Message      ISAPI-SLOT#-4-INVISTA_WARN: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-4-MSM_WARN: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-4-NSP_WARN: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-4-SSM_WARN: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-4-SSN_WARN: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-5

Error Message      ISAPI-SLOT#-5-INVISTA_NOTICE: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-5-MSM_NOTICE: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-5-NSP_NOTICE: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-5-SSM_NOTICE: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-5-SSN_NOTICE: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-6

Error Message      ISAPI-SLOT#-6-INVISTA_INFO: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-6-MSM_INFO: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-6-NSP_INFO: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-6-SSM_INFO: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-6-SSN_INFO: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISAPI-SLOT#-7

Error Message      ISAPI-SLOT#-7-INVISTA_DEBUG: [chars] 

Explanation    Isapi-invista software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-7-MSM_DEBUG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-7-NSP_DEBUG: [chars] 

Explanation    Isapi-nsp software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-7-SSM_DEBUG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

Error Message      ISAPI-SLOT#-7-SSN_DEBUG: [chars] 

Explanation    Isapi software messages

Recommended Action    No action is required.

ISNS Messages

ISNS-2

Error Message      ISNS-2-ISNS_CFS_OPERATION_FAILED: iSNS CFS [chars] failed 

Explanation    ISNS CFS operation failed

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

Error Message      ISNS-2-ISNS_INIT: iSNS initialization of [chars] [chars] 

Explanation    ISNS initialization failed

Recommended Action    Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

IVR Messages

IVR-2

Error Message      IVR-2-AUTOLEARN_ACTION_FAIL: failure happens during constructing 
virtual dynamic pfcid table 

Explanation    This can happen if failure happens during building, distributing or committing the virtual dynamic pfcid table

Recommended Action    Please 1. check the fabric connection or 2. check current virtual user-configured pfcid entries and internally assigned virtual fcid entries for possible conflict

Error Message      IVR-2-AUTOLEARN_FEATURE_NOT_SUPPORT: some switches:[chars] 
dontsupportautolearn'

Explanation    This can happen if some switches doesntsupportthevirtualpfcidautolearnfeature'

Recommended Action    Please upgrade the unsupported switches

Error Message      IVR-2-CFS_PEER_LOST_WITHIN_SESSION: CFS peer with switch wwn [chars] 
was lost in the middle of an active CFS session. Abort the CFS session and re-enter 
the configuration changes 

Explanation    Due to port flaps, link outages, switch restart etc. a CFS peer switch of IVR was lost. The current configuration changes would not be applied to this peer until the peer merges with this switch. The CFS merge may fail if the configuration at the lost peer conflicts with the changes made in this session. Also, IVR auto topology could be out of sync. with this peer. It is recommended that the user abort this CFS session using ivr abort command and then re-enter the configuration changes.

Recommended Action    No action is required.

Error Message      IVR-2-DEVICE_FCID_REWRITE_FAILURE: Failure while programming FCID 
rewrite entries for pWWN [chars] on incoming VSAN [dec]. Device may not be able 
to communicate with its peer devices, failure reason code: [hex] 

Explanation    Failed to program FCID rewrite entries probably because the hardware ran out of FCID rewrite entries. This can happen if there are too many devices in Inter-VSAN zone or too many local VSANs in VSAN topology

Recommended Action    Reduce the number of devices involved in IVR in the active IVR zoneset. Also, reduce the number of redundant transit VSANs, if any

Error Message      IVR-2-DEVICE_STATE_INCOMPATIBLE_WITH_NAT_MODE: State for device with 
port WWN [chars] could not be restored because it was incompatible with the current 
NAT mode([dec]). This probably happened because NAT mode was modified without 
completely deactivating the active IVR zoneset 

Explanation    This probably happened because NAT mode was modified without completely deactivating the active IVR zoneset

Recommended Action    The switch needs to be rebooted

Error Message      IVR-2-DEVICE_VSAN_REWRITE_FAILURE: Failure while programming VSAN 
rewrite entries for pWWN [chars] on incoming VSAN [dec]. Device may not be able 
to communicate with its peer devices 

Explanation    Failed to program VSAN rewrite entries probably because the hardware ran out of VSAN rewrite entries. This can happen if there are too many devices in Inter-VSAN zone or too many local VSANs in VSAN topology

Recommended Action    Reduce the number of domains involved in IVR by moving the members of active IVR zoneset to fewer switches. Also, reduce the number of redundant transit VSANs, if any

Error Message      IVR-2-INTEROP_MODE_2_OR_3_BF_FAILED: [chars] VSAN [dec] Virtual 
Domain [chars] 

Explanation    Build Fabric (BF) failed in VSAN [dec]. The BF was initiated in order to remove an unused virtual domain [dec] from the fcdomain list in that VSAN. The virtual domain still remains in the fcdomain list and hence it would not be available in that VSAN for assignment.

Recommended Action    Perform a manual build fabric using fcdomainsinterfaceifyouwouldliketoremovetheunusedvirtualdomain(s)fromthefcdomainlist.'

Error Message      IVR-2-INTEROP_MODE_2_OR_3_RDI_FAILED: VSAN [dec], requested domain 
[chars], received domain [chars] sWWN [chars]. Return Code [chars] 

Explanation    Request Domain Identifier (RDI) command to allocate virtual domain [dec] failed in VSAN [dec]. Received another domain [chars] instead. IVR-members connected to third-party switch may not participate in IVR communications. It is likely that the domain requested in the RDI command is already in use.

Recommended Action    Reassign the domains so that the domain requested via RDI does not overlap with any existing domain in that VSAN.

Error Message      IVR-2-IVR_DISABLE_FAILED: Inter-VSAN Routing disable failed for 
reason: [chars] 

Explanation    Inter-VSAN Routing disable failed for reason: [chars]. Cleanup might not have completed

Recommended Action    Deactivate ivr zoneset and disable ivr again. If that fails, then the ivr process would terminate itself in 5 minutes

Error Message      IVR-2-IVZS_ACTIVATION_FAILED_RETRYING: Inter-VSAN zoneset activation 
failed in VSAN [dec] : [chars]. retrying after [dec] seconds 

Explanation    Inter-VSAN zoneset activation failed in VSAN [dec] : [chars]. This could be an intermittent regular zoneset activation error. The activation will be retried in [dec] seconds.

Recommended Action    No action is required.

Error Message      IVR-2-NO_LICENSE_SHUTDOWN: Inter-VSAN Routing is shutting down. 

Explanation    License required for continued IVR operation is not available. Hence IVR is shutting down

Recommended Action    Install appropriate license for IVR services and then enable IVR again.

Error Message      IVR-2-NO_LICENSE_WARNING: Inter-VSAN Routing would shutdown in [dec] 
seconds. 

Explanation    License required for continued IVR operation is not available. Unless the required license is installed IVR would shutdown in [dec] seconds. IVR configurations would be lost.

Recommended Action    Install appropriate license for IVR services to continute to operate uninterrupted within [dec] seconds

Error Message      IVR-2-PERSISTENT_VIRTUAL_FCID_CONFLICT_WITH_AUTOLEARN: Persistent 
virtual fcid and dynamic pfcid entries 

Explanation    This can happen if conflict happens during persistent virtual domain, or virtual fcid entry configuration.

Recommended Action    Please assign a non-conflict persistent virtual domain or fcid entry with current dynamic entries

Error Message      IVR-2-PERSISTENT_VIRTUAL_FCID_UNAVAILABLE: to vsan [dec] because the 
configured persistent virtual domain/fcid could not be assigned 

Explanation    This can happen if the virtual domain/fcid configured by the user is - a) Already in use (either by IVR or a real switch) b) Not allowed due to interop mode or allowed domain list

Recommended Action    Please make sure that the configured virtual domain/fcid is allowed and available for use

Error Message      IVR-2-VIRTUAL_DOMAIN_CONFLICT: In VSAN [dec] virtual domain [dec] 
from native VSAN [dec] conflicts with native VSAN [dec] for the same virtual domain 

Explanation    Currently advertised virtual domain [dec] in VSAN [dec] is native to VSAN [dec]. This switch has learned of a device that is member of active IVR zone and has the same domain ID, but belongs to a different native VSAN. This device would not be advertised in that VSAN until the domain conflict is resolved.

Recommended Action    No action is required.

Error Message      IVR-2-VIRTUAL_FCID_UNAVAILABLE: to vsan [dec] because the internally 
generated FCID conflicts with fcid assigned to WWN [chars]. Please configure fcid 
for WWN [chars] too 

Explanation    This can happen if the virtual domain/fcid internally configured is already in use by another active device

Recommended Action    Please assign a different persistent virtual fcid by CLI command

IVR-3

Error Message      IVR-3-AAM_MODE_CANNOT_CHANGE: AAM mode cannot be changed. Might cause 
the fabric NAT mode inconsistency 

Explanation    Could be caused by ivr NAT is not enable

Recommended Action    No action is required.

Error Message      IVR-3-AAM_MODE_DEREGISTERED_FAILED: Abstract ACL Manager (AAM) mode 
deregister failed. Error code is [chars]. 

Explanation    Abstract ACL Manager (AAM) mode deregister failed

Recommended Action    No action is required.

Error Message      IVR-3-AAM_MODE_REGISTERED_FAILED: Abstract ACL Manager (AAM) 
register failed. Error code is [chars]. 

Explanation    Abstract ACL Manager (AAM) register failed

Recommended Action    No action is required.

Error Message      IVR-3-ACL_ERROR: ACL API, [chars], failed with error [chars] 

Explanation    IVR invoked ACL API and received the error code. [chars] describes the API and [chars] specifies the error.

Recommended Action    No action is required.

Error Message      IVR-3-ACL_PERMIT_ENTRY_ERROR: ACL permit entry update on interface 
[chars] failed for reason: [chars] 

Explanation    ACL could not program permit entries for IVR traffic. [chars] describes the interface named and [chars] describes the system error message from ACL. IVR traffic coming from the interface may be dropped.

Recommended Action    If the problem persists, please contact TAC, or your reseller for support.

Error Message      IVR-3-ACL_PLOGI_ENTRY_ERROR: PLOGI capture entry update in slot [dec] 
failed for reason: [chars] 

Explanation    ACL could not program IVR PLOGI could not be programmed. slot[dec] describes the line card slot number and [chars] describes the system error message. PLOGI and its response may be dropped because ivr process cannot capture those frames.

Recommended Action    No action is required.

Error Message      IVR-3-AFID_CONFLICT: [chars] 

Explanation    AFID configuration is different at different ivr-enabled switches in the same VSAN. Change AFID configuration (auto mode) or vsan topology configuration (user mode) to make it consistent

Recommended Action    No action is required.

Error Message      IVR-3-CFS_INVALID_PAYLOAD_RECEIVED: Inter-VSAN process received 
invalid payload from CFS 

Explanation    Inter-VSAN process received invalid payload from CFS.

Recommended Action    No action is required.

Error Message      IVR-3-CLEAR_FAILED: [chars] 

Explanation    An error occurred while clearing the lock. The reason for the failure : [chars]

Recommende