The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Description: Assign a scheduler
Syntax:
WORD |
scheduler name (Max Size 64) |
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']] (config)# firmware (config-firmware)# switch-group <WORD> (config-firmware-switch)# schedule <WORD>
Description: Schedule snapshot export
Syntax:
WORD |
Scheduler name |
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot export <WORD> (config-export)# schedule <WORD>
Description: Pause maintenance policy scheduler
Syntax:
pause |
Pause maintenance policy scheduler |
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']] (config)# firmware (config-firmware)# switch-group <WORD> (config-firmware-switch)# scheduler pause
Description: Scheduler configuration mode
Syntax:
fabric |
Fabric schedules |
controller |
Controller schedules |
schedule |
Configure a schedule |
WORD |
Schedule name (Max size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD>
Description: Set the scheduling algorithm
Syntax:
WORD |
Algorithm to choose |
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# scheduling <WORD>
Description: Specify the scope for the contract
Syntax:
WORD |
Contract Scope |
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# contract <WORD> [type <type>] (config-tenant-contract)# scope <WORD>
Description: Set scope
Syntax:
global |
Route-map will be available for use on all nodes in this tenant and vrf |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# scope global
Description: Configure an SCVMM in the Microsoft domain
Syntax:
arg |
|
cloud |
Cloud name |
WORD |
Cloud Name (Max Size 512) |
name |
(Optional) SCVMM Controller Name |
Command Mode: microsoft-domain : Create a VMM Microsoft Domain
Command Path:
# configure [['terminal', 't']] (config)# microsoft-domain <WORD> (config-microsoft)# scvmm <> cloud <WORD> [name <name>]
Description: Second snapshot file name
Syntax:
FILENAME |
Second snapshot file name |
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot rollback <WORD> (config-rollback)# second-file <FILENAME>
Description: Add security domain
Syntax:
WORD |
Security-domain name |
Command Mode: vlan-domain : Configure vlan domain
Command Path:
# configure [['terminal', 't']] (config)# vlan-domain <name> [dynamic] [type <domain-type>] (config-vlan)# security-domain <WORD>
Description: Add a security domain to this VMware domain
Syntax:
WORD |
Security domain name (Max Size 64) |
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# security-domain <WORD>
Description: Add a security domain to the tenant
Syntax:
domain |
Domain |
WORD |
Security domain name (Max Size None) |
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# security domain <WORD>
Description: Send Community attribute to this neighbor
Syntax:
extended |
(Optional) Send Extended Community attribute |
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router bgp <fabric-ASN> (config-bgp)# vrf member tenant <WORD> vrf <WORD> (config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>] (config-leaf-bgp-vrf-neighbor)# send-community [extended]
Description: Add LDAP server to LDAP group
Syntax:
A.B.C.D|A:B::C:D|WORD |
LDAP server name or IP address |
priority |
priority of server within group |
<0-16> |
Priority of server within group. Number range from=0 to=16 |
Command Mode: aaa group server ldap : LDAP server group name.
Command Path:
# configure [['terminal', 't']] (config)# aaa group server ldap <WORD> (config-ldap)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add RADIUS server to RADIUS group
Syntax:
A.B.C.D|A:B::C:D|WORD |
RADIUS server name or IP address |
priority |
priority of server within group |
<0-16> |
Priority of server within group. Number range from=0 to=16 |
Command Mode: aaa group server radius : RADIUS server group name.
Command Path:
# configure [['terminal', 't']] (config)# aaa group server radius <WORD> (config-radius)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add TACACS PLUS server to TACACS PLUS group
Syntax:
A.B.C.D|A:B::C:D|WORD |
TACACS PLUS server name or IP address |
priority |
priority of server within group |
<0-16> |
Priority of server within group. Number range from=0 to=16 |
Command Mode: aaa group server tacacsplus : TACACS+ server group name.
Command Path:
# configure [['terminal', 't']] (config)# aaa group server tacacsplus <WORD> (config-tacacsplus)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Configure ntp servers for the active ntp policy
Syntax:
WORD |
Server name/IP for the active ntp policy (Max Size 64) |
prefer |
(Optional) Preferred server for the active ntp policy |
arg |
(Optional) Reference key id for authentication. Number range from=1 to=65535 |
arg |
(Optional) Configure management vrf |
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# ntp (config-ntp)# server <WORD> [prefer] [key <>] [use-vrf <>]
Description: Add a destination server
Syntax:
<host/ipaddr> |
The hostname or ipaddress |
facility |
(Optional) The forwarding facility level for logs generated |
severity |
(Optional) The severity level for logs generated |
mgmtepg |
(Optional) MgmtEndpoint |
port |
(Optional) Service port of the remote destination. Number range from=1 to=65535 |
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']] (config)# logging server-group <WORD> (config-logging)# server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg <mgmtepg>] [port <port>]
Description: Specify the QOS service policy
Syntax:
WORD |
Qos Service Policy (Max Size 64) |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# service-policy <WORD>
Description: Specify the QOS service policy
Syntax:
WORD |
Service policy to apply (Max Size 64) |
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l2 epg <WORD> (config-tenant-l2ext-epg)# service-policy <WORD>
Description: QOS service policy
Syntax:
type |
Type of the Qos Policy |
data-plane |
QOS policy for Data Plane Policing |
input |
Ingress Direction |
output |
Egress Direction |
WORD |
Qos Policy Name (Max Size 64) |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface vlan <1-4094> (config-leaf-if)# service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
type |
Type of the Qos Policy |
data-plane |
QOS policy for Data Plane Policing |
input |
Ingress Direction |
output |
Egress Direction |
WORD |
Qos Policy Name (Max Size 64) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
type |
Type of the Qos Policy |
data-plane |
QOS policy for Data Plane Policing |
input |
Ingress Direction |
output |
Egress Direction |
WORD |
Qos Policy Name (Max Size 64) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
type |
Type of the Qos Policy |
data-plane |
QOS policy for Data Plane Policing |
input |
Ingress Direction |
output |
Egress Direction |
WORD |
Qos Policy Name (Max Size 64) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# service-policy type data-plane input|output <WORD>
Description: Configure L4-L7 Service
Syntax:
WORD |
Service node name (Max Size 64) |
WORD |
(Optional) Tenant name (Max Size 63) |
WORD |
(Optional) Device cluster name (Max Size 64) |
Available Modes |
(Optional) Description |
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# l4l7 graph <WORD> [contract <contract-option>] (config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode <Available Modes>]
Description: Enable/Disable refresh in the session records, Comma separated values
Syntax:
<sessionRecordFlags> |
Session record flags as comma separated values like val1,val2,..valN |
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']] (config)# crypto webtoken (config-webtoken)# session-record-flags <sessionRecordFlags>
Description: QOS level for the epg
Syntax:
qos-class |
QOS level for the epg |
WORD |
Qos Level |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# set qos-class <WORD>
Description: QOS level for the application
Syntax:
qos-class |
QOS level for the application |
WORD |
Qos Level |
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# set qos-class <WORD>
Description: Specify the QOS level for the epg
Syntax:
qos-class |
class of QOS to specify |
<contractQosLevel> |
{unspecified|level1|level2|level3} |
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties or create new inband
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# inband-mgmt epg <WORD> (config-inb-epg)# set qos-class <contractQosLevel>
Description: QOS level for the epg
Syntax:
qos-class |
QOS level for the epg |
WORD |
Qos Level |
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l2 epg <WORD> (config-tenant-l2ext-epg)# set qos-class <WORD>
Description: QOS level for the epg
Syntax:
qos-class |
class of QOS to specify |
<contractQosLevel> |
{unspecified|level1|level2|level3} |
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# oob-mgmt epg <epgval> (config-oob-epg)# set qos-class <contractQosLevel>
Description: Burst Rate
Syntax:
<0-4294967295> |
Burst Rate |
UNIT |
Burst Rate Unit |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set burst <0-4294967295> UNIT
Description: Burst Rate
Syntax:
<0-4294967295> |
Burst Rate |
UNIT |
Burst Rate Unit |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set burst <0-4294967295> UNIT
Description: Committed Rate
Syntax:
<0-4294967295> |
Committed Rate |
UNIT |
Committed Rate Unit |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set cir <0-4294967295> UNIT
Description: Committed Rate
Syntax:
<0-4294967295> |
Committed Rate |
UNIT |
Committed Rate Unit |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set cir <0-4294967295> UNIT
Description: Set BGP community attribute
Syntax:
regular |
BGP regular community |
extended |
BGP extended community |
value |
Community value in aa:nn format |
additive |
Add to existing community |
replace |
Replace existing community |
none |
Do not change community |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
regular |
BGP regular community |
extended |
BGP extended community |
value |
Community value in aa:nn format |
additive |
Add to existing community |
replace |
Replace existing community |
none |
Do not change community |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
regular |
BGP regular community |
extended |
BGP extended community |
value |
Community value in aa:nn format |
additive |
Add to existing community |
replace |
Replace existing community |
none |
Do not change community |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
regular |
BGP regular community |
extended |
BGP extended community |
value |
Community value in aa:nn format |
additive |
Add to existing community |
replace |
Replace existing community |
none |
Do not change community |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
regular |
BGP regular community |
extended |
BGP extended community |
value |
Community value in aa:nn format |
additive |
Add to existing community |
replace |
Replace existing community |
none |
Do not change community |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set community regular|extended <value> additive|replace|none
Description: Conform Policer Mark Cos
Syntax:
<0-6> |
Conform Policer Mark Cos |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set conform-cos-transmit <0-6>
Description: Conform Policer Mark Cos
Syntax:
<0-6> |
Conform Policer Mark Cos |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set conform-cos-transmit <0-6>
Description: Conform Policer Mark DSCP
Syntax:
<0-63> |
Conform Policer Mark DSCP |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set conform-dscp-transmit <0-63>
Description: Conform Policer Mark DSCP
Syntax:
<0-63> |
Conform Policer Mark DSCP |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set conform-dscp-transmit <0-63>
Description: Conform Policer Action
Syntax:
WORD |
Conform Policer Action |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set conform <WORD>
Description: Conform Policer Action
Syntax:
WORD |
Conform Policer Action |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set conform <WORD>
Description: Route Flap dampening
Syntax:
<1-60> |
Decay half life. Number range from=1 to=60 |
<1-20000> |
Value to start reusing a route. Number range from=1 to=20000 |
<1-20000> |
Value to start suppressing a route. Number range from=1 to=20000 |
<1-255> |
Maximum suppress time for stable route. Number range from=1 to=255 |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Specify the DSCP level for the EPG
Syntax:
WORD |
DSCP value |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# set dscp <WORD>
Description: Exceed Policer Mark Cos
Syntax:
<0-6> |
Exceed Policer Mark Cos |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set exceed-cos-transmit <0-6>
Description: Exceed Policer Mark Cos
Syntax:
<0-6> |
Exceed Policer Mark Cos |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set exceed-cos-transmit <0-6>
Description: Exceed Policer Mark DSCP
Syntax:
<0-63> |
Exceed Policer Mark DSCP |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set exceed-dscp-transmit <0-63>
Description: Exceed Policer Mark DSCP
Syntax:
<0-63> |
Exceed Policer Mark DSCP |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set exceed-dscp-transmit <0-63>
Description: Exceed Policer Action
Syntax:
WORD |
Exceed Policer Action |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set exceed <WORD>
Description: Exceed Policer Action
Syntax:
WORD |
Exceed Policer Action |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set exceed <WORD>
Description: Excessive Burst Rate
Syntax:
<0-4294967295> |
Excessive Burst Rate |
UNIT |
Excessive Burst Rate Unit |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set excessive-burst <0-4294967295> UNIT
Description: Excessive Burst Rate
Syntax:
<0-4294967295> |
Excessive Burst Rate |
UNIT |
Excessive Burst Rate Unit |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set excessive-burst <0-4294967295> UNIT
Description: BGP local preference path attribute
Syntax:
<0-4294967295> |
Preference value |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
<0-4294967295> |
Preference value |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
<0-4294967295> |
Preference value |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
<0-4294967295> |
Preference value |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
<0-4294967295> |
Preference value |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set local-preference <0-4294967295>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type> |
<metric-type> |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type> |
<metric-type> |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type> |
<metric-type> |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type> |
<metric-type> |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type> |
<metric-type> |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set metric-type <metric-type>
Description: Set metric for destination routing protocol
Syntax:
<0-255> |
Metric value. Number range from=0 to=255 |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
<0-255> |
Metric value. Number range from=0 to=255 |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
<0-255> |
Metric value. Number range from=0 to=255 |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
<0-255> |
Metric value. Number range from=0 to=255 |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
<0-255> |
Metric value. Number range from=0 to=255 |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set metric <NUMBER>
Description: Policer Mode
Syntax:
WORD |
Policer Mode |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set mode <WORD>
Description: Policer Mode
Syntax:
WORD |
Policer Mode |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set mode <WORD>
Description: Peak Rate
Syntax:
<0-4294967295> |
Peak Rate |
UNIT |
Pir Unit |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set pir <0-4294967295> UNIT
Description: Peak Rate
Syntax:
<0-4294967295> |
Peak Rate |
UNIT |
Pir Unit |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set pir <0-4294967295> UNIT
Description: Class of QOS to specify
Syntax:
WORD |
Qos Level |
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# contract <WORD> [type <type>] (config-tenant-contract)# set qos-class <WORD>
Description: Specify the QOS level for the EPG
Syntax:
unspecified |
Unspecified QoS level |
level1 |
QoS level1 |
level2 |
QoS level2 |
level3 |
QoS level3 |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# set qos-class unspecified|level1|level2|level3
Description: Tag value for destination routing protocol
Syntax:
<0-4294967295> |
Tag value. Number range from=0 to=4294967295 |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
<0-4294967295> |
Tag value. Number range from=0 to=4294967295 |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
<0-4294967295> |
Tag value. Number range from=0 to=4294967295 |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
<0-4294967295> |
Tag value. Number range from=0 to=4294967295 |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
<0-4294967295> |
Tag value. Number range from=0 to=4294967295 |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set tag <NUMBER>
Description: class of target dscp to specify
Syntax:
WORD |
Target dscp |
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# contract <WORD> [type <type>] (config-tenant-contract)# set target-dscp <WORD>
Description: class of target dscp to specify
Syntax:
WORD |
Target dscp |
WORD |
Target DSCP Direction |
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# contract <WORD> [type <type>] (config-tenant-contract)# subject <WORD> (config-tenant-contract-subj)# set target-dscp <WORD> WORD
Description: Policer type
Syntax:
WORD |
Policer Type |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set type <WORD>
Description: Policer type
Syntax:
WORD |
Policer Type |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set type <WORD>
Description: Violate Policer Mark Cos
Syntax:
<0-6> |
Violate Policer Mark Cos |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set violate-cos-transmit <0-6>
Description: Violate Policer Mark Cos
Syntax:
<0-6> |
Violate Policer Mark Cos |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set violate-cos-transmit <0-6>
Description: Violate Policer Mark DSCP
Syntax:
<0-63> |
Violate Policer Mark DSCP |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set violate-dscp-transmit <0-63>
Description: Violate Policer Mark DSCP
Syntax:
<0-63> |
Violate Policer Mark DSCP |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set violate-dscp-transmit <0-63>
Description: Violate Policer Action
Syntax:
WORD |
Violate Policer Action |
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# set violate <WORD>
Description: Violate Policer Action
Syntax:
WORD |
Violate Policer Action |
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# set violate <WORD>
Description: Weight value for destination routing protocol
Syntax:
<0-65535> |
Weight value. Number range from=0 to=65535 |
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# vrf context <WORD> (config-tenant-vrf)# route-profile <WORD> (config-tenant-vrf-route-profile)# set weight <NUMBER>
Description: Weight value for destination routing protocol
Syntax:
<0-65535> |
Weight value. Number range from=0 to=65535 |
Command Mode: template route-profile : Configure route-profile template under tenant for BGP dampening and route redistribution
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template route-profile <WORD> tenant <WORD> (config-leaf-template-route-profile)# set weight <NUMBER>
Description: Weight value for destination routing protocol
Syntax:
<0-65535> |
Weight value. Number range from=0 to=65535 |
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> (config-leaf-vrf-route-map-match)# set weight <NUMBER>
Description: Weight value for destination routing protocol
Syntax:
<0-65535> |
Weight value. Number range from=0 to=65535 |
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD> (config-leaf-vrf-route-map-match)# set weight <NUMBER>
Description: Weight value for destination routing protocol
Syntax:
<0-65535> |
Weight value. Number range from=0 to=65535 |
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out for bridge-domain export
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# template route-profile <WORD> (config-leaf-vrf-template-route-profile)# set weight <NUMBER>
Description: Configures the communication policy of the SHELLINABOX feature
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Usage:
In the APIC GUI, the SHELLINABOX feature allows you to open a pop-up SSH session to a fabric switch by right-clicking the icon of the switch. To enable or disable this feature, use the shellinabox command to enter the SHELLINABOX communication policy group, then use the [no] admin-state-enable command.
Command Path:
# configure [['terminal', 't']] (config)# comm-policy <WORD> (config-comm-policy)# shellinabox
Description: Show AAA Authentication information
Command Mode: exec : Exec Mode
Command Path:
# show aaa authentication
Description: Show AAA group information
Command Mode: exec : Exec Mode
Command Path:
# show aaa groups
Description: Show Access-list Information
Syntax:
WORD |
Name of the Contract to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show access-list WORD
Description: CLI configuration command logs
Command Mode: exec : Exec Mode
Command Path:
# show accounting log
NOTE:
This command displays only those changes made using the command line interface (CLI). It does not display changes made using the GUI or the API. To view all changes made in the Management Information Tree, use the show audit detail command.
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show application WORD
Description: Show audit-log information
Syntax:
<log-id> |
(Optional) Log ID |
action<action-type> |
(Optional) Object action indicator |
<user-name> |
(Optional) Name of user |
<num-minutes> |
(Optional) Logs created in time interval. Number range from=1 to=59 |
<num-hours> |
(Optional) Logs created in time interval. Number range from=1 to=23 |
<num-days> |
(Optional) Logs created in time interval. Number range from=1 to=999 |
<YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Logs created in time interval |
end-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Logs created in time interval |
detail |
(Optional) Detailed audit-log information. Displays what was modified and displays the old and new settings. |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show VRF Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show command for BGP peers
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: Show external l3 EIGRP
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show command for external-l3 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: EPG name to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show command for external-l3 static routes
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD detail
Description: Show command for callhome
Syntax:
common |
Common |
Command Mode: exec : Exec Mode
Command Path:
# show callhome common
Description: Show command for callhome destination-profile
Syntax:
common |
Common |
Command Mode: exec : Exec Mode
Command Path:
# show callhome common destination-profile
Description: Show command for callhome destination-profile
Syntax:
common |
Common |
Command Mode: exec : Exec Mode
Command Path:
# show callhome common query-profile
Description: Show command for callhome transport-email
Syntax:
common |
Common |
Command Mode: exec : Exec Mode
Command Path:
# show callhome common transport-email
Description: Show catalog information
Command Mode: exec : Exec Mode
Command Path:
# show catalog
Description: Show Commands Syntax
Syntax:
WORD |
Command Name pattern between single quotes |
<mode-name> |
(Optional) Mode name pattern between single quotes |
details |
(Optional) Show Command Details |
Command Mode: exec : Exec Mode
Command Path:
# show cli command <WORD> [mode <mode-name>]
Description: Show Commands Audit
Command Mode: exec : Exec Mode
Command Path:
# show cli internal audit
Description: Show Transaction Details
Syntax:
logs |
Show Transaction Logs |
xml |
Show Transaction XML Post |
<Transaction ID> |
Transaction ID(TID) to grep log lines with similar TIDs. TID can be extracted from the 'show cli internal audit' command. Number range from=0 to=9223372036854775807 |
Command Mode: exec : Exec Mode
Command Path:
# show cli internal transaction logs|xml <NUMBER>
Description: Show all cli-related commands
Syntax:
<mode-name> |
(Optional) Mode name pattern between single quotes |
details |
(Optional) Show Command Details |
Command Mode: exec : Exec Mode
Command Path:
# show cli list [mode <mode-name>]
Description: Show Commands ManPage
Syntax:
WORD |
Command Name pattern between single quotes |
<mode-name> |
(Optional) Mode name pattern between single quotes |
details |
(Optional) Show Command Details |
Command Mode: exec : Exec Mode
Command Path:
# show cli manpage <WORD> [mode <mode-name>]
Description: Show Commands Path
Syntax:
WORD |
Command Name pattern between single quotes |
<mode-name> |
(Optional) Mode name pattern between single quotes |
details |
(Optional) Show Command Details |
Command Mode: exec : Exec Mode
Command Path:
# show cli path <WORD> [mode <mode-name>]
Description: Show clock information
Command Mode: exec : Exec Mode
Command Path:
# show clock
Description: HTTPS service cipher suite listings
Command Mode: exec : Exec Mode
Command Path:
# show communication ciphers
Description: HTTP service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication http
Description: HTTPS service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication https
Description: Shellinabox service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication shellinabox
Description: SSH service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication ssh-service
Description: Telnet service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication telnet
Description: Status of last web requests
Command Mode: exec : Exec Mode
Command Path:
# show communication web-requests
Description: Show Contracts Information Based on Type
Syntax:
WORD |
whitelist (permit) or blacklist(deny) or oob-mgmt type of contract |
Command Mode: exec : Exec Mode
Command Path:
# show contract-type WORD
Description: Show Contracts Information
Syntax:
WORD |
Name of the Contract to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show contract WORD
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show controller
Description: Detailed controller information
Syntax:
node-id |
(Optional) Optional Serial number |
Command Mode: exec : Exec Mode
Command Path:
# show controller detail [id <node-id>]
Description: Show all core dumps
Command Mode: exec : Exec Mode
Command Path:
# show cores
Description: Show Counter information
Syntax:
<node-name> |
Node name |
<process> |
Process name |
<counterTopics> |
Counter Topics |
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> counter <counterTopics>
Description: Show log level information
Syntax:
<node-name> |
Node name |
<process> |
Process name |
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> log
Description: Show dns address information
Command Mode: exec : Exec Mode
Command Path:
# show dns-address
Description: Show dns domain information
Command Mode: exec : Exec Mode
Command Path:
# show dns-domain
Description: Show IP endpoints
Syntax:
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints on an interface ethernet
Syntax:
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
ethernet [<fex>/]<slot>/<port> |
Ethernet Range |
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface port-channel
Syntax:
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Port Channel Name (Max Size 64) |
<101-164> |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on vpc
Syntax:
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
context |
VPC Context |
WORD |
First VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Second VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
interface |
VPC Interface name |
vpc |
VPC Interface name |
WORD |
VPC Name (Max Size 64) |
fex |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Description: Show Application EPG Information
Syntax:
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD
Description: Show detailed view of Application EPg
Syntax:
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD detail
Description: Show event information
Syntax:
<event-code> |
(Optional) Event code |
<event-ID> |
(Optional) Event ID |
<event-value> |
(Optional) Cause |
last-minutes <num-minutes> |
(Optional) Event activity in time interval. Number range from=1 to=59 |
last-hours <num-hours> |
(Optional) Event activity in time interval. Number range from=1 to=23 |
last-days <num-days> |
(Optional) Event activity in time interval. Number range from=1 to=999 |
start-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Event activity in time interval |
end-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Event activity in time interval |
detail |
(Optional) Detailed event information |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Detailed controller information
Syntax:
node-id |
(Optional) Optional Serial number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Show command for leaf
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show extended chassis information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description: Port channel interface
Syntax:
<leafId> |
Leaf id |
<portChan> |
<Port channel number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
<ch> |
None |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for leaf port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<leafPort> |
pls enter the leaf port number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Virtual port channel information
Syntax:
<leafId> |
Leaf id |
<vpcPort> |
pls enter virtual port channel number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Show command for spine
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show information for fabric module
Syntax:
<leafId> |
Leaf id |
<fcMod> |
pls enter the fabric module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for system module
Syntax:
<leafId> |
Leaf id |
<sysMod> |
pls enter the system module number |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show IP endpoints
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints on an interface ethernet
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
ethernet [<fex>/]<slot>/<port> |
Ethernet Range |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface port-channel
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Port Channel Name (Max Size 64) |
<101-164> |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on vpc
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
context |
VPC Context |
WORD |
First VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Second VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
interface |
VPC Interface name |
vpc |
VPC Interface name |
WORD |
VPC Name (Max Size 64) |
fex |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show VRF Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show command for BGP peers
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: Show external l3 EIGRP
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show command for external-l3 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: EPG name to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show command for external-l3 route-map
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<l3out name> |
(Optional) Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show external-l3 route-map in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<l3out name> |
(Optional) Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Description: Show command for external-l3 static routes
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: Show command for external-l2 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg
Description: EPG name to filter on
Syntax:
WORD |
Name of the EPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg name WORD
Description: tenant to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg tenant WORD
Description: Show command for BGP peers
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp
Description: tenant to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD>
Description: vrf to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD node <101-4000>
Description: Show command for external-l3 eigrp
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp detail
Description: node(s) to filter on
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000>
Description: Show interanl details
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000> detail
Description: tenant(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> detail
Description: vrf(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD detail
Description: node(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail
Description: Show command for external-l3 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg
Description: external-l3 epg in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg detail
Description: EPG name to filter on
Syntax:
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName> detail
Description: tenant to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> detail
Description: vrf to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD detail
Description: Show command for external-l3 interfaces
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces detail
Description: node(s) to filter on
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000>
Description: Show interanl details
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000> detail
Description: tenant(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> detail
Description: vrf(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD detail
Description: node(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail
Description: Show command for external-l3 ospf
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf detail
Description: node(s) to filter on
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000>
Description: Show interanl details
Syntax:
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000> detail
Description: tenant(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> detail
Description: vrf(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD detail
Description: node(s) to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000>
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF(s) to filter on (Max Size 64) |
<101-4000> |
Node Range or Node Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail
Description: Show command for external-l3 route-map
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map
Description: Route-map in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map detail
Description: Route-map name to filter on
Syntax:
<l3out name> |
Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name>
Description: Route-map in detail with operational status
Syntax:
<l3out name> |
Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name> detail
Description: tenant to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD>
Description: Route-map in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> detail
Description: vrf to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD
Description: Route-map in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node
Description: Route-map in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node detail
Description: Show command for external-l3 static routes
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route
Description: static-route in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route detail
Description: node to filter on
Syntax:
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node detail
Description: tenant to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD>
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> detail
Description: vrf to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node detail
Description: Show fabric recovery status
Command Mode: exec : Exec Mode
Command Path:
# show fabric-recovery status
Description: Show fault information
Syntax:
history |
(Optional) Historical information |
<fault-code> |
(Optional) Fault code |
<fault-ID> |
(Optional) Fault ID |
<yes/no> |
(Optional) Acknowledgment status |
<lc-state> |
(Optional) Lifecycle state |
<severity-value> |
(Optional) Severity |
<severity-value> |
(Optional) Minimum severity |
<fault-type> |
(Optional) Type |
<fault-value> |
(Optional) Cause |
last-minutes <num-minutes> |
(Optional) Fault activity in time interval. Number range from=1 to=59 |
last-hours <num-hours> |
(Optional) Fault activity in time interval. Number range from=1 to=23 |
last-days <num-days> |
(Optional) Fault activity in time interval. Number range from=1 to=999 |
start-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Fault activity in time interval |
end-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Fault activity in time interval |
detail |
(Optional) Detailed faults information |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Detailed controller information
Syntax:
node-id |
(Optional) Optional Serial number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Show L4 L7 Device information
Syntax:
Tenant Name |
(Optional) Name of Tenant |
Device Cluster Name |
(Optional) Name of Device |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Graph information
Syntax:
<Tenant Name> |
(Optional) Name of Tenant |
<Graph Name> |
(Optional) Name of Graph |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show command for leaf
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show extended chassis information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description: Port channel interface
Syntax:
<leafId> |
Leaf id |
<portChan> |
<Port channel number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
<ch> |
None |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for leaf port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<leafPort> |
pls enter the leaf port number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Virtual port channel information
Syntax:
<leafId> |
Leaf id |
<vpcPort> |
pls enter virtual port channel number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain
Description: Microsoft domain name
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
WORD |
Microsoft domain name |
WORD |
HyperV hostname |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft port group information
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> port-group
Description: Show Microsoft SCVMM information
Syntax:
WORD |
Microsoft domain name |
<hostname|ip> |
SCVMM hostname or IP |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft VM information
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm
Description: Show detailed Microsoft VM information
Syntax:
WORD |
Microsoft domain name |
WORD |
VM Name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm name <WORD>
Description: Show command for spine
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show information for fabric module
Syntax:
<leafId> |
Leaf id |
<fcMod> |
pls enter the fabric module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for system module
Syntax:
<leafId> |
Leaf id |
<sysMod> |
pls enter the system module number |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show VRF Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show command for BGP peers
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: Show external l3 EIGRP
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show command for external-l3 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: EPG name to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show command for external-l3 static routes
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain
Description: VMware domain name
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name>
Description: Show VMware domain EPG details
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> epg
Description: Show VMware ESX information
Syntax:
<name> |
VMware domain name |
<esx-ip> |
ESX IP |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> esx <esx-ip>
Description: Show VMware port group information
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> port-group
Description: VMware vCenter ip or hostname
Syntax:
<name> |
VMware domain name |
<hostname|ip> |
vCenter hostname or IP |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vcenter <hostname|ip>
Description: Show VMware VM information
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm
Description: Show detailed VMware VM information
Syntax:
<name> |
VMware domain name |
<vm-name> |
VM Name |
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm name <vm-name>
Description: Show firmware images present in repository
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository
Description: Detailed repository information
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository detail
Description: Upgrade status of all controllers and switches
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status
Description: Controller-group upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group
Description: Detailed upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group detail
Description: Detailed upgrade status information
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status detail
Description: Switch-group upgrade status
Syntax:
WORD |
switch-group name (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD>
Description: Detailed upgrade status
Syntax:
WORD |
switch-group name (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD> detail
Description: Show health score information
Syntax:
history |
(Optional) Historical information |
min-change <percentage change> |
(Optional) Minimum change in health score percentage. Number range from=-100 to=9999 |
max-hs <maximum health-score> |
(Optional) Maximum health score. Number range from=0 to=100 |
start-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Health activity in time interval |
end-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Health activity in time interval |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>
Description: Show L4 L7 Device information
Syntax:
Tenant Name |
(Optional) Name of Tenant |
Device Cluster Name |
(Optional) Name of Device |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Graph information
Syntax:
<Tenant Name> |
(Optional) Name of Tenant |
<Graph Name> |
(Optional) Name of Graph |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show command for leaf
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>
Description: Show extended chassis information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt <mgmtPort>
Description: Port channel interface
Syntax:
<leafId> |
Leaf id |
<portChan> |
<Port channel number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface portchannel <portChan>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
<ch> |
None |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis <ch>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for leaf port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<leafPort> |
pls enter the leaf port number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor <supMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>
Description: Virtual port channel information
Syntax:
<leafId> |
Leaf id |
<vpcPort> |
pls enter virtual port channel number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>
Description: Show command for spine
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet <phyInt>
Description: L3 instance
Syntax:
<leafId> |
Leaf id |
<l3Inst> |
<L3 instance number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface l3instance <l3Inst>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt <mgmtPort>
Description: Tunnel Interface
Syntax:
<leafId> |
Leaf id |
<tunnelPort> |
<Tunnel interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel <tunnelPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis
Description: Show information for fabric module
Syntax:
<leafId> |
Leaf id |
<fcMod> |
pls enter the fabric module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric <fcMod>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot>
Description: Show information for fabric port
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
<fabPort> |
pls enter the fabric port number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory supervisor <supMod>
Description: Show information for system module
Syntax:
<leafId> |
Leaf id |
<sysMod> |
pls enter the system module number |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system <sysMod>
Description: Show command for protocol
Syntax:
<leafId> |
Leaf id |
<protName> |
Protocol name |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>
Description: Vrf information
Syntax:
<leafId> |
Leaf id |
<vrfPort> |
pls enter vrf name |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD epg WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD detail
Description: Show VRF Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail
Description: Show command for BGP peers
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: Show external l3 EIGRP
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show command for external-l3 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: EPG name to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf detail
Description: Show command for external-l3 static routes
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node detail
Description: show inband mgmt epgs on all the nodes
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt
Description: show inband mgmt epgs on the controller
Syntax:
<controller-id> |
|
WORD |
(Optional) Epg Name of conusmer epg |
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt controller <controller-id> [epg <WORD>]
Description: show inband mgmt epgs on the node
Syntax:
<switch-id> |
|
WORD |
(Optional) Epg Name |
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt switch <switch-id> [epg <WORD>]
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD detail
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show ip interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show ipv6 interface bridge-domain WORD
Description: Show L4 L7 Device information
Syntax:
Tenant Name |
(Optional) Name of Tenant |
Device Cluster Name |
(Optional) Name of Device |
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Graph information
Syntax:
<Tenant Name> |
(Optional) Name of Tenant |
<Graph Name> |
(Optional) Name of Graph |
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4-L7 package information
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-package
Description: Show LDAP server information
Command Mode: exec : Exec Mode
Command Path:
# show ldap-server
Description: Show command for locator-led
Syntax:
status |
locator-led status |
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status
Description: Leaf to filter on
Syntax:
status |
locator-led status |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status leaf
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain
Description: Microsoft domain name
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
WORD |
Microsoft domain name |
WORD |
HyperV hostname |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft port group information
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> port-group
Description: Show Microsoft SCVMM information
Syntax:
WORD |
Microsoft domain name |
<hostname|ip> |
SCVMM hostname or IP |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft VM information
Syntax:
WORD |
Microsoft domain name |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm
Description: Show detailed Microsoft VM information
Syntax:
WORD |
Microsoft domain name |
WORD |
VM Name |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm name <WORD>
Description: Show Microsoft VM information
Syntax:
WORD |
(Optional) Specify a VM name |
A.B.C.D |
(Optional) Specify a VM IP address |
AA:BB:CC:DD:EE:FF |
(Optional) Specify a VM MAC address |
Command Mode: exec : Exec Mode
Command Path:
# show microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]
Description: Show monitor session for access interfaces
Syntax:
session |
session |
session_name |
session name |
Command Mode: exec : Exec Mode
Command Path:
# show monitor access session session_name
Description: Show monitor session for fabric interfaces
Syntax:
session |
session |
session_name |
session name |
Command Mode: exec : Exec Mode
Command Path:
# show monitor fabric session session_name
Description: Show monitor session for tenant
Syntax:
tenant_name |
tenant |
session |
session |
session_name |
session name |
Command Mode: exec : Exec Mode
Command Path:
# show monitor tenant <tenant_name> session session_name
Description: Show monitor session for virtual switches
Syntax:
session |
session |
WORD |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show monitor virtual session WORD
Description: Show ntpq information
Command Mode: exec : Exec Mode
Command Path:
# show ntpq
Description: Show Out of band Information
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt
Description: show oob mgmt epgs on the controller, enter one
Syntax:
<controller-id> |
|
WORD |
(Optional) Epg Name of conusmer epg |
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt controller <controller-id> [epg <WORD>]
Description: show oob mgmt epgs on the node, enter one
Syntax:
<switch-id> |
|
WORD |
(Optional) Epg Name of conusmer epg |
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt switch <switch-id> [epg <WORD>]
Description: Show policy maps
Command Mode: exec : Exec Mode
Command Path:
# show policy-map
Description: data-plane type policy-map(s)
Syntax:
infra |
Global data-plane policy-map(s) |
WORD |
data-plane type policy-map(s) (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type data-plane infra WORD
Description: QOS type policy-map(s)
Syntax:
WORD |
QOS type policy-map(s) (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type qos WORD
Description: show leaf port-channel info
Syntax:
WORD |
Leaf Range or Leaf Name List |
<port-channel-list> |
port channel names |
Command Mode: exec : Exec Mode
Command Path:
# show port-channel leaf WORD <port-channel-list>
Description: show port-channel mapping
Syntax:
<port-channel-list> |
port channel names |
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list>
Description: leaf
Syntax:
<port-channel-list> |
port channel names |
WORD |
Leaf Range or Leaf Name List |
<101-164> |
(Optional) Fex ID |
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list> leaf WORD [fex <101-164>]
Description: Show RADIUS server information
Command Mode: exec : Exec Mode
Command Path:
# show radius-server
Description: resource
Syntax:
conflict |
show resource conflicts in APIC |
encap-vlan |
show resource conflicts of encap-vlan in APIC |
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan
Description: Epg Name
Syntax:
conflict |
show resource conflicts in APIC |
encap-vlan |
show resource conflicts of encap-vlan in APIC |
WORD |
Epg Name |
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD>
Description: Node ID
Syntax:
conflict |
show resource conflicts in APIC |
encap-vlan |
show resource conflicts of encap-vlan in APIC |
WORD |
Epg Name |
<101-4000> |
Leaf ID |
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD> node <101-4000>
Description: Show information about AAA Roles
Command Mode: exec : Exec Mode
Command Path:
# show role
Description: show running configuration
Syntax:
all |
(Optional) show running-config with defaults |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show running-config [all] <scope>
Description: Show session-log information
Syntax:
<log-id> |
(Optional) Log ID |
action<action-type> |
(Optional) Object action indicator |
<user-name> |
(Optional) Name of user |
<num-minutes> |
(Optional) Logs created in time interval. Number range from=1 to=59 |
<num-hours> |
(Optional) Logs created in time interval. Number range from=1 to=23 |
<num-days> |
(Optional) Logs created in time interval. Number range from=1 to=999 |
<YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Logs created in time interval |
end-time <YYYY-MM-DDTHR:MIN:SEC> |
(Optional) Logs created in time interval |
detail |
(Optional) Detailed session-log information. Displays the action trigger that shows why a login occurred. |
<scope> |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Detailed controller information
Syntax:
node-id |
(Optional) Optional Serial number |
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Show command for leaf
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show command for spine
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Show command for active snapshot job
Syntax:
job |
View active snapshot job |
Command Mode: exec : Exec Mode
Command Path:
# show snapshot active job
Description: Show command for snapshot files
Command Mode: exec : Exec Mode
Command Path:
# show snapshot files
Description: Show command for snapshot jobs
Command Mode: exec : Exec Mode
Command Path:
# show snapshot jobs
Description: Show snmp policy information
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>]
Description: Show snmp client group policies
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] clientgroups
Description: Show snmp community information
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] community
Description: Show snmp v3 engine-id
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] engineid
Description: Show snmp trap hosts
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] hosts
Description: Show snmp v3 users
Syntax:
policy |
(Optional) SNMP policy name |
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] users
Description: Show statistics
Syntax:
granularity |
Choose granularity value |
<granularity-value> |
<granularity-value> |
history |
(Optional) historical stats information |
cumulative |
(Optional) cumulative stats information |
tenant |
command scope |
leaf |
command scope |
spine |
command scope |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine
Description: Show command for leaf
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId>
Description: Show extended chassis information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<fexNum> |
pls enter fex number |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface ethernet <phyInt>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface mgmt <mgmtPort>
Description: Port channel interface
Syntax:
<leafId> |
Leaf id |
<portChan> |
<Port channel number> |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface portchannel <portChan>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory supervisor <supMod>
Description: Show command for spine
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId>
Description: Ethernet IEEE 802.3z
Syntax:
<leafId> |
Leaf id |
<phyInt> |
<slot or chassis-number/port or slot number> |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface ethernet <phyInt>
Description: Management interface
Syntax:
<leafId> |
Leaf id |
<mgmtPort> |
<Management interface number> |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface mgmt <mgmtPort>
Description: Show inventory chassis information
Syntax:
<leafId> |
Leaf id |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory chassis
Description: Show information for fabric module
Syntax:
<leafId> |
Leaf id |
<fcMod> |
pls enter the fabric module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fabric <fcMod>
Description: Show inventory fan information
Syntax:
<leafId> |
Leaf id |
<ftSlot> |
pls enter fan tray number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fans <ftSlot>
Description: Show inventory module information
Syntax:
<leafId> |
Leaf id |
<lcSlot> |
please enter the module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory module <lcSlot>
Description: Show inventory power supply information
Syntax:
<leafId> |
Leaf id |
<psuSlot> |
pls enter the powersupply number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory powersupply <psuSlot>
Description: Show information for supervisor module
Syntax:
<leafId> |
Leaf id |
<supMod> |
pls enter the supervisor module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory supervisor <supMod>
Description: Show information for system module
Syntax:
<leafId> |
Leaf id |
<sysMod> |
pls enter the system module number |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory system <sysMod>
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD epg WORD
Description: Show switch information
Command Mode: exec : Exec Mode
Command Path:
# show switch
Description: Show switch detailed information
Syntax:
switch-id |
(Optional) Optional switch id. Number range from=0 to=9223372036854775807 |
Command Mode: exec : Exec Mode
Command Path:
# show switch detail [id <switch-id>]
Description: Show tacacs server information
Command Mode: exec : Exec Mode
Command Path:
# show tacacs-server
Description: Techsupport status for all
Syntax:
status |
Status |
Command Mode: exec : Exec Mode
Command Path:
# show techsupport all status
Description: Techsupport status for controllers
Syntax:
status |
Status |
Command Mode: exec : Exec Mode
Command Path:
# show techsupport controllers status
Description: Techsupport status for host
Syntax:
<Odevid> |
Specify the host Odev ID. Number range from=0 to=9223372036854775807 |
status |
Status |
Command Mode: exec : Exec Mode
Command Path:
# show techsupport host <NUMBER> status
Description: Techsupport status for switch
Syntax:
switchId <switchId> |
switch id 101-4000 or range(s): 101-103,104 |
status |
Status |
Command Mode: exec : Exec Mode
Command Path:
# show techsupport switch switchId <switchId> status
Description: Show Tenants Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD
Description: Show Access-list Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the Contract to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD access-list WORD
Description: Show Application Profiles Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD
Description: Show IP endpoints
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints on an interface ethernet
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
ethernet [<fex>/]<slot>/<port> |
Ethernet Range |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface port-channel
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Port Channel Name (Max Size 64) |
<101-164> |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on vpc
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
context |
VPC Context |
WORD |
First VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Second VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
interface |
VPC Interface name |
vpc |
VPC Interface name |
WORD |
VPC Name (Max Size 64) |
fex |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD
Description: Show detailed view of Application EPg
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD detail
Description: Show IP endpoints
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints on an interface ethernet
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
ethernet [<fex>/]<slot>/<port> |
Ethernet Range |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface port-channel
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Port Channel Name (Max Size 64) |
<101-164> |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on vpc
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the application we eventually want to filter on (Max Size 64) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
context |
VPC Context |
WORD |
First VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Second VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
interface |
VPC Interface name |
vpc |
VPC Interface name |
WORD |
VPC Name (Max Size 64) |
fex |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD detail
Description: Show Contracts Information Based on Type
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
whitelist (permit) or blacklist(deny) or oob-mgmt type of contract |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract-type WORD
Description: Show Contracts Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the Contract to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract WORD
Description: Show detailed view of tenant
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD detail
Description: Show IP endpoints
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints on an interface ethernet
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
ethernet [<fex>/]<slot>/<port> |
Ethernet Range |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface port-channel
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
WORD |
Leaf Number (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Port Channel Name (Max Size 64) |
<101-164> |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on vpc
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
type |
(Optional) Endpoint Type |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
<1-4094> |
(Optional) Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
A:B::C:D |
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xx |
context |
VPC Context |
WORD |
First VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
WORD |
Second VPC leaf (Max Size 4000). Number range from=0 to=9223372036854775807 |
interface |
VPC Interface name |
vpc |
VPC Interface name |
WORD |
VPC Name (Max Size 64) |
fex |
(Optional) Fex Id. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Description: Show Application EPG Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD
Description: Show detailed view of Application EPg
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the AEPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD detail
Description: Show command for external-l2 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the EPG to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD external-l2 epg WORD
Description: Show Bridge-domain Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Detailed Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD detail
Description: Show command for IP properties on interface BD
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ip interface bridge-domain WORD
Description: Show command for IP properties on interface BD
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the bridge-domain (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ipv6 interface bridge-domain WORD
Description: Show policy maps
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map
Description: data-plane type policy-map(s)
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
data-plane type policy-map(s) (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type data-plane WORD
Description: QOS type policy-map(s)
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
QOS type policy-map(s) (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type qos WORD
Description: Show VRF Information
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD detail
Description: Show command for BGP peers
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<101-4000> |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: Show external l3 EIGRP
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp detail
Description: Show command for external-l3 epgs
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: EPG name to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: external-l3 epg in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<epgName> |
Name of the EPG to filter on |
<epgName> |
Name of the EPG to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces detail
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf
Description: Show interanl details
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf detail
Description: Show command for external-l3 route-map
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<l3out name> |
(Optional) Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show external-l3 route-map in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
<l3out name> |
(Optional) Name of the route-map to filter on |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Description: Show command for external-l3 static routes
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route detail
Description: node to filter on
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node
Description: static-route in detail with operational status
Syntax:
WORD |
Name of the tenant to filter on (Max Size 63) |
WORD |
Name of the VRF to filter on (Max Size 64) |
arg |
Leaf Range or Leaf Name List |
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node detail
Description: Show session
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name>
Description: Show atomic counters
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> atomiccounter
Description: Show audit
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> audit
Description: Show contracts
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> contracts
Description: Show deployment changes
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> deployments
Description: Show events
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> events
Description: Show faults
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> faults
Description: Show monitor
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> monitor
Description: Show reports
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> reports
Description: Show statistics
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> statistics
Description: Show topology
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> topology
Description: Show traceroute
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> traceroute
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext sessions
Description: Show session
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name>
Description: Show atomic counters
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> atomiccounter
Description: Show audit
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> audit
Description: Show contracts
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> contracts
Description: Show deployment changes
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> deployments
Description: Show events
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> events
Description: Show faults
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> faults
Description: Show monitor
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> monitor
Description: Show reports
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> reports
Description: Show statistics
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> statistics
Description: Show topology
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> topology
Description: Show traceroute
Syntax:
session_name |
Session name |
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> traceroute
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep sessions
Description: Show user information
Syntax:
WORD |
User name |
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD>
Description: Show user information
Syntax:
WORD |
User name |
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD> detail
Description: Show version information
Command Mode: exec : Exec Mode
Command Path:
# show version
Description: Show command for vlan-domain
Syntax:
arg |
(Optional) Vlan-domain name |
<vlan-range> |
(Optional) VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19 |
arg |
(Optional) Leaf id. Number range from=101 to=4000 |
detail |
(Optional) vlan-domain in detail with concrete MOs |
Command Mode: exec : Exec Mode
Command Path:
# show vlan-domain [name <>] [vlan] [leaf <>] [detail]
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain
Description: VMware domain name
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name>
Description: Show VMware domain EPG details
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> epg
Description: Show VMware ESX information
Syntax:
<name> |
VMware domain name |
<esx-ip> |
ESX IP |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> esx <esx-ip>
Description: Show VMware port group information
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> port-group
Description: VMware vCenter ip or hostname
Syntax:
<name> |
VMware domain name |
<hostname|ip> |
vCenter hostname or IP |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vcenter <hostname|ip>
Description: Show VMware VM information
Syntax:
<name> |
VMware domain name |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm
Description: Show detailed VMware VM information
Syntax:
<name> |
VMware domain name |
<vm-name> |
VM Name |
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm name <vm-name>
Description: Show VMware VM information
Syntax:
WORD |
(Optional) Specify a VM name |
A.B.C.D |
(Optional) IP address in format i.i.i.i |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
Command Mode: exec : Exec Mode
Command Path:
# show vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: show vpc mapping
Syntax:
map |
map by name |
<vpc-list> |
vpc names |
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list>
Description: leaf
Syntax:
map |
map by name |
<vpc-list> |
vpc names |
WORD |
Leaf Range or Leaf Name List |
<101-164> |
(Optional) Fex ID. Number range from=101 to=164 |
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list> leaf WORD [fex <NUMBER>]
Description: Show VRF Information
Syntax:
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD
Description: Show detailed view of VRF
Syntax:
WORD |
Name of the VRF to filter on (Max Size 64) |
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD detail
Description: Disable BFD
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# shut
Description: Disable monitor session
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD> (config-monitor-virtual)# shut
Description: Administrative state of the Policer
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']] (config)# policy-map type data-plane <WORD> (config-pmap-dpp)# shutdown
Description: Disable the class of service specified
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# shutdown
Description: Administrative state of the Policer
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type data-plane <WORD> (config-tenant-pmap-dpp)# shutdown
Description: Disable Interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# shutdown
Description: Disable Port Channel
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# shutdown
Description: Disable interface
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# shutdown
Description: Disable monitor session
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# shutdown
Description: Disable monitor session
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name> (config-monitor-fabric)# shutdown
Description: Disable monitor session
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <session_name> (config-monitor-tenant)# shutdown
Description: ID of the network where the site is deployed
Syntax:
WORD |
The site id (Max Size 512) surrounded by quotes |
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# site-id <WORD>
Description: Configure BFD SLOW-TIMER value in milliseconds
Syntax:
<interval> |
BFD interval. Number range from=1000 to=30000 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# slow-timer <NUMBER>
Description: Configuration snapshot download setup mode
Syntax:
WORD |
Snapshot downloader name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot download <WORD>
Description: Configuration export setup mode
Syntax:
WORD |
Export configuration name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot export <WORD>
Description: Configuration import setup mode
Syntax:
WORD |
Import configuration name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot import <WORD>
Description: Configuration rollback setup mode
Syntax:
WORD |
Rollback configuration name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot rollback <WORD>
Description: Configuration snapshot upload setup mode
Syntax:
WORD |
Snapshot uploader name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot upload <WORD>
Description: Configure SNMP client-group
Syntax:
<group-name> |
SNMP clientgroup |
<mgmt-epg> |
(Optional) Management EPG (default: oob-default) |
<ip-address/hostname> |
(Optional) Ip-address/hostname of the snmp client |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client <ip-address/hostname>]
Description: Configure SNMP community
Syntax:
<community-name> |
SNMP community |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server community <community-name>
Description: Configure SNMP contact
Syntax:
<contact-name> |
SNMP contact name |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server contact <contact-name>
Description: Configure SNMP trap host
Syntax:
<ip-address/hostname> |
Ip-address/hostname of the snmp trap destination |
traps-version |
SNMP Version to use for traps |
1 |
Use SNMPv1 |
2c |
Use SNMPv2 |
3 |
Use SNMPv3 |
<community> |
SNMP community/security |
auth |
Use Authentication Only |
none |
Use No Authentication |
priv |
Use Authentication and Encryption |
<port> |
(Optional) UDP port for traps (default 162) |
<mgmt-epg> |
(Optional) Management EPG (default: oob-default) |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server host <ip-address/hostname> traps-version 1|2c|3 <community> auth|none|priv [udp-port <port>] [management-epg <mgmt-epg>]
Description: Configure SNMP location
Syntax:
<location-name> |
SNMP location |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server location <location-name>
Description: Enable SNMP protocol
Syntax:
enable |
Enable SNMP protocol |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server protocol enable
Description: Configure SNMP user
Syntax:
<user-name> |
SNMP user |
auth |
Authentication Type |
sha |
Use HMAC SHA algorithm for authentication |
md5 |
Use HMAC MD5 algorithm for authentication |
<auth-key> |
Authentication password for user (Min Size 8, Max Size 130) |
priv |
Privacy Type |
aes |
Use 128-bit AES algorithm for privacy |
des |
Use 64-bit DES algorithm for privacy |
none |
Do not use privacy |
<priv-key> |
(Optional) Privacy passphrase for user (Min Size 8, Max Size 130) |
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# snmp-server user <user-name> auth sha|md5 <auth-key> priv aes|des|none [privacy-passphrase <priv-key>]
Description: Configure monitor virtual source
Syntax:
tenant |
tenant |
WORD |
tenant name (Max Size 63) |
application |
application |
WORD |
application name (Max Size 64) |
epg |
epg |
WORD |
epg name (Max Size 64) |
E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE |
(Optional) MAC address (Option 1) MAC address (Option 2) MAC address (Option 3) MAC address (Option 4) |
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD> (config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Description: Configure EPG as monitor source
Syntax:
application_name |
application name (Max Size 64) |
epg |
epg |
epg_name |
epg name (Max Size 64) |
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <session_name> (config-monitor-tenant)# source application <application_name> epg <epg_name>
Description: Configure monitor for ethernet access interfaces
Syntax:
<ethernet> |
List of ethernet itfs |
leaf |
leaf |
<leaf Id> |
leaf Id |
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>
Description: Configure monitor for ethernet fabric interfaces
Syntax:
<ethernet> |
ethernet interface range |
switch |
switch |
<switch Id> |
switch Id |
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name> (config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>
Description: Configure monitor for port-channel interfaces
Syntax:
<port-channel list> |
<port-channel list> |
leaf |
leaf |
<leaf Id> |
leaf Id |
<fex Id> |
(Optional) fex Id |
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id> [fex <fex Id>]
Description: Configure monitor for VPC interfaces
Syntax:
<vpc list> |
<vpc list> |
leaf |
leaf |
<leaf Id1> |
leaf Id1 |
<leaf Id2> |
leaf Id2 |
<fex Ids> |
(Optional) paired fex Ids |
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex <fex Ids>]
Description: STP MST configuration mode
Syntax:
mst |
Multiple spanning tree |
configuration |
Configure multiple spanning tree protocol |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# spanning-tree mst configuration
Description: Add spanning tree
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']] (config)# template leaf-policy-group <WORD> (config-leaf-policy-group)# spanning-tree
Description: Enable or Disable BPDU filter/guard
Syntax:
bpdu-filter |
Don't send or receive BPDUs on this interface |
bpdu-guard |
Don't accept BPDUs on this interface |
<enable|disable> |
enable/disable BPDU filter/guard |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: enable BPDU filter/guard
Syntax:
bpdu-filter |
Don't send or receive BPDUs on this interface |
bpdu-guard |
Don't accept BPDUs on this interface |
<enable|disable> |
enable/disable BPDU filter/guard |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or disable BPDU filter/guard
Syntax:
bpdu-filter |
Don't send or receive BPDUs on this interface |
bpdu-guard |
Don't accept BPDUs on this interface |
<enable|disable> |
enable/disable BPDU filter/guard |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: enable BPDU filter/guard
Syntax:
bpdu-filter |
Don't send or receive BPDUs on this interface |
bpdu-guard |
Don't accept BPDUs on this interface |
<enable|disable> |
enable/disable BPDU filter/guard |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Spanning Tree Subsystem
Syntax:
bpdu-filter |
Don't send or receive BPDUs on this interface |
bpdu-guard |
Don't accept BPDUs on this interface |
<enable|disable> |
enable/disable BPDU filter/guard |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Configure BPDU filter override on AVS uplink ports
Syntax:
enable |
Enable BPDU filter |
disable |
Disable BPDU filter |
default |
Remove BPDU filter/guard override policy |
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# configure-avs (config-vmware-avs)# spanning-tree bpdu-filter enable|disable|default
Description: Configure BPDU guard override on AVS uplink ports
Syntax:
enable |
Enable BPDU guard |
disable |
Disable BPDU guard |
default |
Remove BPDU filter/guard override policy |
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# configure-avs (config-vmware-avs)# spanning-tree bpdu-guard enable|disable|default
Description: Configure Interface Speed
Syntax:
<interfaceSpeed> |
Interface Speed Policy |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
<portChannelSpeed> |
Port-Channel Speed Policy |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# speed <portChannelSpeed>
Description: Configure Interface Speed
Syntax:
<interfaceSpeed> |
Interface Speed Policy |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
<speed> |
Speed Value |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# speed <speed>
Description: Configure Interface Speed
Syntax:
<speed> |
Interface Speed Policy |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# speed <speed>
Description: Set the ISIS SPF maximal wait interval
Syntax:
level-1 |
Level 1 |
<50-120000> |
SPF maximum wait interval. Number range from=50 to=120000 |
<50-120000> <50-120000> |
Initial and secondary wait intervals (both values are required) |
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']] (config)# pod 1 (config-pod)# isis fabric (config-pod-isis)# spf-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Update ssh key for the user for ssh authentication
Syntax:
WORD |
A name for SSH key (Max Size 64) |
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']] (config)# username <WORD> (config-username)# ssh-key <WORD>
Description: SSH communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']] (config)# comm-policy <WORD> (config-comm-policy)# ssh-service
Description: Set the SSL protocol (comma separated values)
Syntax:
sslProtocols |
SSL Protocols as comma separated values like val1,val2,..valN |
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']] (config)# comm-policy <WORD> (config-comm-policy)# https (config-https)# ssl-protocols <sslProtocols>
Description: Set the LDAP Server SSL Certificate validation level
Syntax:
<ssl-validation-level> |
<ssl-validation-level> |
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']] (config)# ldap-server host <A.B.C.D|A:B::C:D|WORD> (config-host)# ssl-validation-level <ssl-validation-level>
Description: Set The state or province in which the organization is located.
Syntax:
<WORD> |
state or province (Max Size 64) |
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']] (config)# crypto keyring <WORD> (config-keyring)# csr (config-csr)# state <WORD>
Description: Cipher state
Syntax:
cipherState |
Cipher state as comma separated values like val1,val2,..valN |
Command Mode: ciphers : HTTPS cipher suite
Command Path:
# configure [['terminal', 't']] (config)# comm-policy <WORD> (config-comm-policy)# https (config-https)# ciphers <WORD> (config-ciphers)# state <cipherState>
Description: Configure Silent Host behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
A1.B1.C1.D1,...,An.Bn.Cn.Dn |
(Optional) List of IP addresses in format i.i.i.i |
A1:B1::C1:D1,..,An:Bn::Cn:Dn |
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
A1.B1.C1.D1,...,An.Bn.Cn.Dn |
(Optional) List of IP addresses in format i.i.i.i |
A1:B1::C1:D1,..,An:Bn::Cn:Dn |
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
A1.B1.C1.D1,...,An.Bn.Cn.Dn |
(Optional) List of IP addresses in format i.i.i.i |
A1:B1::C1:D1,..,An:Bn::Cn:Dn |
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xx |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
VLAN range. Number range from=1 to=4094 |
A.B.C.D |
IP address in format i.i.i.i |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
VLAN range. Number range from=1 to=4094 |
A.B.C.D |
IP address in format i.i.i.i |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
mac |
MAC address |
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
vlan |
Encapsulation Vlan |
<1-4094> |
VLAN range. Number range from=1 to=4094 |
A.B.C.D |
IP address in format i.i.i.i |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Enable/disable stats collection on VCenter (DVS-only)
Syntax:
enable |
enable |
Command Mode: vcenter : Configure a VCenter in the VMware domain
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>] (config-vmware-vc)# statistics enable
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
<0-100> |
Rate of Bandwidth in Percentage |
<0-100> |
(Optional) Max Rate of Bandwidth in Percentage |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
<0-100> |
Rate of Bandwidth in Percentage |
<0-100> |
(Optional) Max Rate of Bandwidth in Percentage |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
<0-100> |
Rate of Bandwidth in Percentage |
<0-100> |
(Optional) Max Rate of Bandwidth in Percentage |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
<0-100> |
Rate of Bandwidth in Percentage |
<0-100> |
(Optional) Max Rate of Bandwidth in Percentage |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
<0-100> |
Rate of Bandwidth in Percentage |
<0-100> |
(Optional) Max Rate of Bandwidth in Percentage |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control in packet per second on the Interface
Syntax:
arg |
Burst Rate in packets per second. Number range from=0 to=4882812 |
burst-rate |
Max Burst Rate in packets per second |
arg |
Max Burst Rate in packets per second. Number range from=0 to=4882812 |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# storm-control pps <> burst-rate <>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
arg |
Burst Rate in packets per second. Number range from=0 to=4882812 |
burst-rate |
Max Burst Rate in packets per second |
arg |
Max Burst Rate in packets per second. Number range from=0 to=4882812 |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# storm-control pps <> burst-rate <>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
arg |
Burst Rate in packets per second. Number range from=0 to=4882812 |
burst-rate |
Max Burst Rate in packets per second |
arg |
Max Burst Rate in packets per second. Number range from=0 to=4882812 |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# storm-control pps <> burst-rate <>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
arg |
Burst Rate in packets per second. Number range from=0 to=4882812 |
burst-rate |
Max Burst Rate in packets per second |
arg |
Max Burst Rate in packets per second. Number range from=0 to=4882812 |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# storm-control pps <> burst-rate <>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
arg |
Burst Rate in packets per second. Number range from=0 to=4882812 |
burst-rate |
Max Burst Rate in packets per second |
arg |
Max Burst Rate in packets per second. Number range from=0 to=4882812 |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# storm-control pps <> burst-rate <>
Description: Street address of the site
Syntax:
WORD |
The street address (Max Size 255) surrounded by quotes |
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# street-address <WORD>
Description: Set The fully qualified domain name or DN of the requesting device.
Syntax:
<WORD> |
FQDN or DN of device (Max Size 64) |
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']] (config)# crypto keyring <WORD> (config-keyring)# csr (config-csr)# subject <WORD>
Description: Configuration a subject on the contract
Syntax:
WORD |
Name of the contract subject (Max Size 64) |
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# contract <WORD> [type <type>] (config-tenant-contract)# subject <WORD>
Description: Route summarization
Syntax:
IP-PREFIX/LEN |
Summarized ip |
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router ospf default (config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD> (config-leaf-ospf-vrf)# summary-address <IP-PREFIX/LEN>
Description: Create switch firmware upgrade policy
Syntax:
WORD |
switch-group name (Max Size 64) |
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# firmware (config-firmware)# switch-group <WORD>
Description: Add switches to switch group
Syntax:
arg |
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']] (config)# firmware (config-firmware)# switch-group <WORD> (config-firmware-switch)# switch
Description: Configure Leaf Node
Syntax:
arg |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# switch
Description: Add switches to zone
Syntax:
arg |
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']] (config)# zones (config-zones)# zone <WORD> (config-zone)# switch
Description: Configure switching mode.
Syntax:
mode |
switching Mode |
vlan |
VLAN/SW Mode |
vxlan |
VXLAN/SW Mode |
vxlan-ns |
VXLAN/HW Mode |
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# configure-avs (config-vmware-avs)# switching mode vlan|vxlan|vxlan-ns
Description: L2 configuration
Syntax:
vlan |
|
scope |
|
local |
Local Scope |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# switchport vlan scope local
Description: L2 configuration
Syntax:
vlan |
|
scope |
|
local |
Local Scope |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# switchport vlan scope local
Description: Configure switchport parameters
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport
Description: Configure switchport parameters
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport
Description: Configure switchport parameters
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport
Description: Application Name
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Associate SVI to the L2 Access Interface
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
vlan |
Access Vlan |
<1-4094> |
Access Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Configure External L2 connectivity to inband Mnaagement
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
A.B.C.D/LEN |
Gateway IP Address for External Connectivity format x.x.x.x/m |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Description: Add an AEPg as static encap
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
WORD |
Tenant hosting the EPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
primary-vlan <evlan> |
(Optional) Vlan for egress traffic when EPG isolation is enforced |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD> [primary-vlan primary-vlan <evlan>]
Description: Add an AEPg as static encap
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Add an AEPg as static encap
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
WORD |
Tenant hosting the EPg (Max Size 63) |
epg |
L2 external EPG name |
WORD |
L2 external EPG name (Max Size 64) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
epg |
L2 external EPG name |
WORD |
L2 external EPG name (Max Size 64) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
epg |
L2 external EPG name |
WORD |
L2 external EPG name (Max Size 64) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Associate SVI to the L2 Interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
WORD |
Tenant hosting the EPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Interface
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Add legacy forwarding on the vlan supplied
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
WORD |
Tenant hosting the EPg (Max Size 63) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Add legacy forwarding on the vlan supplied
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Add legacy forwarding on the vlan supplied
Syntax:
vlan |
Encapsulation Vlan |
<1-4094> |
Encapsulation Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the EPg |
WORD |
Tenant hosting the EPg (Max Size 63) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Application hosting the AEPg
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the AEPg
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the AEPg
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
WORD |
Application Name (Max Size 64) |
epg |
EPg that uses the statically enabled Encap |
WORD |
EPg that uses the statically enabled Encap (Max Size 64) |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Associate SVI to the L2 Trunk Interface
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate Native Vlan to the L2 Trunk Interface as external SVI
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Trunk L2 Interface
Syntax:
vlan |
Native Vlan |
<1-4094> |
Native Vlan. Number range from=1 to=4094 |
tenant |
Tenant hosting the AEPg |
WORD |
Tenant hosting the AEPg (Max Size 63) |
l3out |
(Optional) Specify one or more l3extOut to add SVI interface |
WORD |
l3extOut Name |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: L2 configuration
Syntax:
scope |
|
local |
Local Scope |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# switchport vlan scope local
Description:
Syntax:
scope |
|
local |
Local Scope |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# switchport vlan scope local
Description:
Syntax:
scope |
|
local |
Local Scope |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# switchport vlan scope local
Description: Syslog common policy configuration mode
Syntax:
common |
Syslog common policy configuration mode |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# syslog common
Description: Set APIC cluster size
Syntax:
<size> |
size of the cluster to be set. Number range from=1 to=16 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system cluster-size <NUMBER>
Description: Configure Controller Id for controllers in fabric
Syntax:
serial-number |
Controller serial number |
approve |
Approve controller |
reject |
Reject controller |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system controller-id <serial-number> approve|reject
Description: Configure dynamic load balancer
Syntax:
mode |
Dynamic load balancer mode |
link-failure-resiliency |
Link failure resiliency mode |
dynamic-aggressive |
Aggressive dynamic mode |
dynamic-conservative |
Conservative dynamic mode |
packet-prioritization |
Packet prioritization mode |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system dynamic-load-balance mode link-failure-resiliency|dynamic-aggressive|dynamic-conservative|packet-prioritization
Description: Set strict/permissive mode for ACI Fabric Internode Authentication
Syntax:
<mode> |
Security mode as comma separated values like val1,val2,..valN |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system fabric-security-mode <mode>
Description: MTU size for Host Facing ports
Syntax:
<576-9000> |
Enter jumbomtu. Number range from=576 to=9000 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system jumbomtu <NUMBER>
Description: Configure Node Id for switches in fabric
Syntax:
serial-number |
Switch serial number |
node-Id |
Switch ID. Number range from=101 to=4000 |
name |
Switch name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# system switch-id <serial-number> <node-Id> <name>