Contents
CDP Commands on Cisco IOS XR Software
This module describes the Cisco IOS XR software commands for monitoring the networking device and network using Cisco Discovery Protocol (CDP).
For detailed information about CDP concepts, configuration tasks, and examples, see the Implementing CDP on Cisco IOS XR Software module in Cisco IOS XR System Management Configuration Guide for the Cisco XR 12000 Series Router.
- cdp
- cdp advertise v1
- cdp holdtime
- cdp log adjacency changes
- cdp timer
- clear cdp counters
- clear cdp table
- show cdp
- show cdp entry
- show cdp interface
- show cdp neighbors
- show cdp traffic
cdp
To enable the Cisco Discovery Protocol (CDP) globally or on an interface, use the cdp command in the appropriate configuration mode. To disable CDP globally or on an interface, use the no form of this command.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
By default, CDP is disabled globally. To enable CDP, CDP must be enabled globally and then enabled for each interface.
To enable CDP globally, use the cdp command in global configuration mode. To disable CDP globally, use the no form of this command in global configuration mode.
To enable CDP on a specific interface, use the cdp command in interface configuration mode. To disable CDP on a specific interface, use the no form of this command in interface configuration mode.
Task ID
Examples
The following example shows how to globally enable CDP:
RP/0/0/CPU0:router(config)# cdp
The following example shows how to enable CDP on an interface:
RP/0/0/CPU0:router(config)# interface gigabitethernet 0/0/0/1 RP/0/0/CPU0:router(config-if)# cdpThe following example shows how to disable CDP on an interface:
RP/0/0/CPU0:router(config)# interface gigabitethernet 0/0/0/1 RP/0/0/CPU0:router(config-if)# no cdpcdp advertise v1
To change the version of Cisco Discovery Protocol (CDP) that is used to communicate with neighboring devices to version 1 (CDPv1), use the cdp advertise v1 command in global configuration mode. To remove the cdp advertise v1 command from the configuration file and restore the system to its default condition with respect to this command, use the no form of this command.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
CDPv2 packets are sent by default. CDP also sends and receives CDPv1 packets if the device with which CDP is interacting does not process CDPv2 packets.
CDPv2 adds device information over CDPv1. The additional information that is contained in the CDPv2 messages relates to Native VLAN, VLAN Trunking Protocol (VTP) Management Domain, Ethernet Duplex, and other features.
Task ID
Examples
The following example shows how to set a networking device to send and receive only CDPv1 advertisements:
RP/0/0/CPU0:router(config)# cdp advertise v1
The following example shows how to restore the default condition (sending and receiving CDPv2 advertisements):
RP/0/0/CPU0:router(config)# no cdp advertise
cdp holdtime
To specify the time for which the receiving device should hold a Cisco Discovery Protocol (CDP) packet from your networking device before discarding it, use the cdp holdtime command in global configuration mode. To remove the cdp holdtime command from the configuration file and restore the system to its default condition with respect to this command, use the no form of this command.
Syntax Description
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
CDP packets are sent with a time-to-live value or holdtime, that is nonzero after an interface is enabled.
The CDP holdtime must be set to a higher number of seconds than the time between CDP transmissions, which is set using the cdp time command.
Task ID
Examples
The following example shows how to specify that the CDP packets sent from the networking device are held by the receiving device for 60 seconds before being discarded. You might want to set the holdtime lower than the default setting of 180 seconds if information about your networking device changes often and you want the receiving devices to purge this information more quickly.
RP/0/0/CPU0:router(config)# cdp holdtime 60
cdp log adjacency changes
To log changes to the Cisco Discovery Protocol (CDP) adjacency table, use the cdp log adjacency changes command in global configuration mode. To disable the logging, use the no form of this command.
Command History
Release
Modification
Release 3.3.0
This command was introduced.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
When CDP adjacency table logging is enabled, a syslog is generated each time a CDP neighbor is added or removed.
Task ID
Examples
The following example shows how to enable CDP adjacency table logging:
RP/0/0/CPU0:router# configure RP/0/0/CPU0:router(config)# cdp log adjacency changesWhen CDP adjacency table logging is enabled, a syslog is generated each time a CDP neighbor is added or removed. The following is an example of the log entry:
LC/0/5/CPU0:Jun 5 10:51:18.081 : cdp[109]: %L2-CDP-6-DELETED_NEIGHBOR : CDP Neighbour TBA04110127 on interface GigabitEthernet0/5/0/0 has been deleted, remote interface 3/2 LC/0/5/CPU0:Jun 5 10:51:33.120 : cdp[109]: %L2-CDP-6-NEW_NEIGHBOR : New CDP neighbor TBA04110127 detected on interface GigabitEthernet0/5/0/0, remote interface 3/2cdp timer
To specify how often the software sends Cisco Discovery Protocol (CDP) updates, use the cdp timer command in global configuration mode. To remove the cdp timer global configuration command from the configuration file and restore the system to its default condition with respect to this command, use the no form of this command.
Syntax Description
seconds Frequency with which the Cisco IOS XR software sends CDP updates, in seconds. Range is 5 to 254. The default is 60.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
A lower timer setting causes CDP updates to be sent more frequently.
Task ID
Examples
The following example shows how to set the CDP timer to 80 seconds, which is less frequent than the default setting of 60 seconds:
RP/0/0/CPU0:router(config)# cdp timer 80
clear cdp counters
To reset Cisco Discovery Protocol (CDP) traffic counters to zero (0), use the clear cdp counters command in EXEC mode.
Syntax Description
location node-id Clears CDP traffic counters for the designated node. The node-id argument is entered in the rack/slot/module notation.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
Examples
The following example shows how to clear CDP counters. The show cdp traffic output shows that all traffic counters have been reset to zero (0).
RP/0/0/CPU0:router# clear cdp counters RP/0/0/CPU0:router# show cdp traffic CDP counters: Packets output: 0, Input: 0 Hdr syntax: 0, Chksum error: 0, Encaps failed: 0 No memory: 0, Invalid packet: 0, Truncated: 0 CDP version 1 advertisements output: 0, Input: 0 CDP version 2 advertisements output: 0, Input: 0 Unrecognize Hdr version: 0, File open failed: 0clear cdp table
To clear and automatically resize the table that contains Cisco Discovery Protocol (CDP) information about neighbors, use the clear cdp table command in EXEC mode.
Syntax Description
location node-id Clears and resizes the CDP table for the designated node. The node-id argument is entered in the rack/slot/module notation.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the clear cdp table command to clear and resize the CDP table that contains the neighbor entries. The new table size is calculated according to the recommended hash table size, as seen in the show cdp command output.
Task ID
Examples
The following example shows how to clear and resize the CDP table. The output of the show cdp neighbors command before and after use of the clear cdp table command shows that all information has been deleted from the table:
RP/0/0/CPU0:router# show cdp neighbors Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater Device ID Local Intrfce Holdtme Capability Platform Port ID TBA04341195(15la Mg0/RP1/CPU0/0 171 T S WS-C2924 0/1 RP/0/0/CPU0:router# clear cdp table RP/0/0/CPU0:router# show cdp neighbors Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater Device ID Local Intrfce Holdtme Capability Platform Port IDThe show cdp command shows that the table has been resized:
RP/0/0/CPU0:router# show cdp Global CDP information: Sending CDP packets every 60 seconds Sending a holdtime value of 180 seconds Sending CDPv2 advertisements is enabled
show cdp
To display global Cisco Discovery Protocol (CDP) information, including CDP version, timer, and holdtime information, use the show cdp command in EXEC mode.
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show cdp command to display CDP version, timer, and holdtime information relative to CDP operations.
Task ID
Examples
The following example shows how to use the show cdp command to verify the CDP global settings:
RP/0/0/CPU0:router# show cdp Global CDP information: Sending CDP packets every 20 seconds Sending a holdtime value of 30 seconds Sending CDPv2 advertisements is not enabled
Table 1 show cdp Field Descriptions Field
Definition
Sending CDP packets every 20 seconds
Interval between transmissions of CDP advertisements. This field is controlled by the cdp timer command.
Sending a holdtime value of 30 seconds
Time for which the device directs the neighbor to hold a CDP advertisement before discarding it. This field is controlled by the cdp holdtime command.
Sending CDPv2 advertisements is not enabled
State of being enabled or disabled for the transmission of CDP version 2-type advertisements. This field is controlled by the cdp advertise v1 command.
Related Commands
Command
Description
Changes the version of CDP that is used to communicate with neighboring devices to CDPv1.
Specifies the time for which the receiving device should hold a CDP packet sent by your networking device before discarding it.
Specifies how often the software sends CDP updates.
Clears and resizes the table that contains CDP information about neighbors.
Displays information about a specific neighboring device or all neighboring devices discovered using CDP.
Displays information about the interfaces on which CDP is enabled.
Displays information about neighboring devices discovered by CDP.
Displays traffic information between devices, gathered using CDP.
show cdp entry
To display information about a specific neighboring device or all neighboring devices discovered using Cisco Discovery Protocol (CDP), use the show cdp entry command in EXEC mode.
Syntax Description
* Displays all CDP neighbors.
entry-name Name of a neighbor about which you want information.
protocol (Optional) Displays protocol information associated with CDP neighbor entries.
version (Optional) Displays version information associated with CDP neighbor entries.
Command Default
This command displays information about a particular device that has been discovered by CDP.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
Examples
The following example shows sample output from the show cdp entry command. Information about device ID, address, platform, interface, holdtime, and version is displayed.
RP/0/0/CPU0:router# show cdp entry TBA04341195 ------------------------- Device ID: TBA04341195(sys-235) SysName : sys-235 Entry address(es): IP address: 172.16.23.9 Platform: WS-C6006, Capabilities: Trans-Bridge Switch Interface: MgmtEth0/RP1/CPU0/0 Port ID (outgoing port): 4/18 Holdtime : 157 sec Version : WS-C6006 Software, Version McpSW: 7.2(2) NmpSW: 7.2(2) Copyright (c) 1995-2002 by Cisco Systems advertisement version: 2 VTP Management Domain: 'sys' Native VLAN: 125 Duplex: full
Table 2 show cdp entry Field Descriptions Field
Description
Device ID
ID code assigned during installation of the router.
Entry address(es)
Addresses of the platform, selected interface, and port ID.
Platform
Platform name.
Capabilities
Special functions that the platform can perform (in this case the platform is a trans-bridge switch).
Interface
Interface location expressed in rack / slot / module / port notation.
Port ID (outgoing port)
Location of the port in use by the interface.
Holdtime
Time (in seconds) for which the device directs the neighbor to hold a CDP advertisement before discarding it. This field is controlled by the cdp holdtime command.
Version
Software version.
advertisement version
Version number of the advertising protocol.
VTP Management Domain
VLAN Trunking Protocol (VTP) domain name of neighbor device.
Native VLAN
VLAN ID.
Duplex
Duplex setting: half or full.
Related Commands
show cdp interface
To display information about the interfaces on which Cisco Discovery Protocol (CDP) is enabled, use the show cdp interface command in EXEC mode.
Syntax Description
type (Optional) Interface type. For more information, use the question mark ( ? ) online help function.
interface-path-id (Optional) Physical interface or virtual interface.
Note Use the show interfaces command to see a list of all interfaces currently configured on the router.
For more information about the syntax for the router, use the question mark (?) online help function.
location node-id (Optional) Displays detailed CDP information for the designated node. The node-id argument is entered in the rack/slot/module notation.
Command Default
This command displays information about the interfaces on which CDP has been enabled.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show cdp interface command to display information about any CDP interfaces. When an interface is specified in the command syntax, information is displayed about the specific interface. Not specifying the interface displays information about all interfaces.
Task ID
Examples
The following example shows sample output from the show cdp interface command. Information about the status, CDP timer, and holdtime settings is displayed for all interfaces on which CDP is enabled.
RP/0/0/CPU0:router# show cdp interface POS0/2/0/0 is Up Encapsulation HDLC Sending CDP packets every 120 seconds Holdtime is 240 seconds POS0/2/0/1 is Up Encapsulation HDLC Sending CDP packets every 120 seconds Holdtime is 240 seconds POS0/2/0/2 is Up Encapsulation HDLC Sending CDP packets every 120 seconds Holdtime is 240 seconds POS0/2/0/3 is Up Encapsulation HDLC Sending CDP packets every 120 seconds Holdtime is 240 seconds MgmtEth0/RP1/CPU0/0 is Up Encapsulation ARPA Sending CDP packets every 120 seconds Holdtime is 240 seconds
The following example shows sample output from the show cdp interface command with an interface specified. Information about the status, CDP timer, and holdtime settings is displayed for Packet-over-SONET/SDH (POS) interface 0/2/0/1 only.
RP/0/0/CPU0:router# show cdp interface pos 0/2/0/1 POS0/2/0/1 is Up Encapsulation HDLC Sending CDP packets every 60 seconds Holdtime is 180 seconds
Table 3 show cdp interface Field Descriptions Field
Description
POS0/2/0/1 is Up
Current condition of POS interface 0/0/2/1.
Encapsulation HDLC
Interface is encoding packets using the Cisco HDLC Layer 2 encapsulation.
Sending CDP packets every 60 seconds
Interval between transmissions of CDP advertisements. This field is controlled by the cdp timer command.
Holdtime is 180 seconds
Time for which the device directs the neighbor to hold a CDP advertisement before discarding it. This field is controlled by the cdp holdtime command.
Related Commands
Command
Description
Displays global CDP information, including timer and holdtime information.
Displays information about a specific neighboring device or all neighboring devices discovered using CDP.
Displays information about neighboring devices discovered by CDP.
Displays traffic information between devices gathered using CDP.
show cdp neighbors
To display detailed information about neighboring devices discovered using Cisco Discovery Protocol (CDP), use the show cpd neighbors command in EXEC mode.
Syntax Description
type (Optional) Interface type. For more information, use the question mark ( ? ) online help function.
interface-path-id (Optional) Physical interface or virtual interface.
Note Use the show interfaces command to see a list of all interfaces currently configured on the router.
For more information about the syntax for the router, use the question mark (?) online help function.
location node-id (Optional) Displays detailed CDP information for the designated node. The node-id argument is entered in the rack/slot/module notation.
detail (Optional) Displays detailed information about a neighbor or neighbors, including network address, enabled protocols, holdtime, and software version. The output includes information about both IPv4 and IPv6 addresses.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show cpd neighbors command to display information about any CDP neighbors. When a location is specified in the command syntax, information about the neighbor is displayed for the specified node. Not specifying the location displays information about the neighbor for all interfaces.
Use the command with the detail keyword to display additional information, including IPv6 neighbors.
Task ID
Examples
The following example shows sample output from the show cpd neighbors command:
RP/0/0/CPU0:router# show cdp neighbors Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater Device ID Local Intrfce Holdtme Capability Platform Port ID TBA04110127 Gi0/7/0/0 173 T S WS-C6506 3/9 cisco_1 Gi0/7/0/2 171 R C12K Gi0/4/0/2
Table 4 show cdp neighbors Field Descriptions Field
Description
Capability Codes
Type of device that can be discovered.
Device ID
Name of the neighbor device.
Local Intrfce
Protocol being used by the connectivity media and the interface number.
Holdtme
Remaining time, in seconds, for which the current device holds the CDP advertisement from a sending router before discarding it.
Capability
Type of the device listed in the CDP Neighbors table. Values are as follows:
R—Router
T—Transparent bridge
B—Source-routing bridge
S—Switch
H—Host
I—Internet Group Management Protocol (IGMP) device
r—Repeater
Platform
Product number of the device.
Port ID
Protocol and port number of the device.
The following examples illustrates sample output for IPv4 and IPv6 neighbors from the show cpd neighbors command with the detail keyword:
RP/0/0/CPU0:router# show cdp neighbor detail ------------------------- Device ID: uut-user SysName : uut-user Entry address(es): IPv4 address: 1.1.1.1 IPv6 address: 1::1 IPv6 address: 2::2 Platform: cisco 12008/GRP, Capabilities: Router Interface: Gi0/4/0/3 Port ID (outgoing port): Gi0/2/0/3 Holdtime : 177 sec Version : Cisco IOS XR Software, Version 0.0.0[Default] Copyright (c) 2005 by cisco Systems, Inc. advertisement version: 2
Table 5 show cdp neighbors detail Field Descriptions Field
Definition
Device ID
Name of the neighbor device.
Entry address(es)
List of network addresses of neighbor devices. The address can be in IP or in Connectionless Network Service (CLNS) protocol conventions.
Platform
Product name and number of the neighbor device.
Capabilities
Device type of the neighbor. This device can be a router, a bridge, a transparent bridge, a source-routing bridge, a switch, a host, an IGMP device, or a repeater.
Interface
Interface being used by the connectivity medium.
Port ID
Port number of the port on the current device.
Holdtime
Remaining time (in seconds) for which the current device holds the CDP advertisement from a sending router before discarding it.
Version
Software version of the neighbor device.
advertisement version
Version number of the advertising protocol.
Related Commands
Command
Description
Displays global CDP information, including timer and holdtime information.
Displays information about a specific neighboring device or all neighboring devices discovered using CDP.
Displays information about the interfaces on which CDP is enabled.
Displays traffic information between devices gathered using CDP.
show cdp traffic
To display information about the traffic gathered between devices using Cisco Discovery Protocol (CDP), use the show cdp traffic command in EXEC mode.
Syntax Description
location node-id (Optional) Displays CDP information for the CDP packets sent and received on the designated node only. The node-id argument is entered in the rack/slot/module notation.
Command History
Release
Modification
Release 3.2
This command was introduced.
Release 3.3.0
No modification.
Release 3.4.0
No modification.
Release 3.5.0
No modification.
Release 3.6.0
No modification.
Release 3.7.0
No modification.
Release 3.8.0
No modification.
Release 3.9.0
No modification.
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
Examples
The following example illustrates sample output from the show cdp traffic command:
RP/0/0/CPU0:router# show cdp traffic CDP counters : Packets output: 50662, Input: 40414 Hdr syntax: 0, Chksum error: 0, Encaps failed: 0 No memory: 0, Invalid packet: 0, Truncated: 0 CDP version 1 advertisements output: 0, Input: 0 CDP version 2 advertisements output: 50662, Input: 40414 Unrecognize Hdr version: 0, File open failed: 0
Table 6 show cdp traffic Field Descriptions Field
Definition
Packets output
Number of CDP advertisements sent by the local device. Note that this value is the sum of the CDP version 1 advertisements output field and the CDP version 2 advertisements output field.
Input
Number of CDP advertisements received by the local device. Note that this value is the sum of the CDP version 1 advertisements input field and the CDP version 2 advertisements input field.
Hdr syntax
Number of CDP advertisements having bad headers that have been received by the local device.
Chksum error
Number of times the checksum (verifying) operation failed on incoming CDP advertisements.
Encaps failed
Number of times CDP failed to send advertisements on an interface because of a failure caused by the bridge port of the local device.
No memory
Number of times that the local device did not have enough memory to store the CDP advertisements in the advertisement cache table when the device was attempting to assemble advertisement packets for transmission and parse them when receiving them.
Invalid packet
Number of invalid CDP advertisements received and sent by the local device.
Truncated
Number of times truncated CDP advertisements were sent because there was not enough space in the CDP packet to hold all CDP type-length-values (TLVs).
CDP version 1 advertisements output
Number of CDP version 1 advertisements sent by the local device.
Input
Number of CDP version 1 advertisements received by the local device.
CDP version 2 advertisements output
Number of CDP version 2 advertisements sent by the local device.
Input
Number of CDP version 2 advertisements received by the local device.
Unrecognize Hdr version
Number of packets received from a CDP version that was outside the current configuration.
File open failed
Number of times that CDP failed to connect to one of the underlying services it uses.
Related Commands
Command
Description
Displays global CDP information, including timer and holdtime information.
Displays information about a specific neighboring device or all neighboring devices discovered using CDP.
Displays information about the interfaces on which CDP is enabled.
Displays information about neighboring devices discovered by CDP.