Recommended Practices for the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
Preventing Electrostatic Discharge Damage
General Maintenance Guidelines
Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
Small Form-Factor Pluggable Status LED
Installing Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
Tools and Equipment Required During Installation
This document provides information that you should know before and during the installation of the Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules (NIMs) in the Cisco 4000 Series Integrated Services Routers. This document contains the following sections:
■Recommended Practices for the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
■Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
■Installing Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs
The Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules (NIMs) are software-configurable high-speed connectivity routing port network interface modules for the Cisco 4000 and Cisco ISR 4300 Series Integrated Services Routers (ISR). These network interface modules provide increased density of Ethernet interfaces on the Cisco 4000 and Cisco ISR 4300 Series ISR. Table 1 lists the network interface modules.
This section describes recommended practices for safe and effective installation of the hardware described in this document.
■Preventing Electrostatic Discharge Damage
■General Maintenance Guidelines
Safety warnings included in this section apply to the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs that are used on Cisco 4000 Series Integrated Services Routers.
To prevent hazardous conditions, follow these safety recommendations while working with this equipment:
■Keep tools away from walk areas where you or others could fall over them.
■Do not wear loose clothing around the router. Fasten your tie or scarf and roll up your sleeves to prevent clothing from being caught in the chassis.
■Wear safety glasses when working under any conditions that might be hazardous to your eyes.
■Locate the emergency power-off switch in the room before you start working. If an electrical accident occurs, shut the power off.
■Before working on the router, turn off the power and unplug the power cord.
■Disconnect all power sources before doing the following:
–Installing or removing a router chassis
■Do not work alone if potentially hazardous conditions exist.
■Always check that power is disconnected from a circuit.
■Remove possible hazards from your work area, such as damp floors, ungrounded power extension cables, or missing safety grounds.
■If an electrical accident occurs, proceed as follows:
–Use caution; do not become a victim yourself.
–Turn off power to the room using the emergency power-off switch.
–Determine the condition of the victim and send another person to get medical aid or call for help.
–Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.
Electrostatic discharge can damage equipment and electrical circuitry. Electrostatic discharge occurs when electronic printed circuit cards, such as those used in Cisco service modules and network modules, are improperly handled and can result in complete or intermittent equipment failure. Always observe the following electrostatic discharge damage (ESD) prevention procedures when installing, removing, or replacing any electronic printed circuit cards:
■Make sure that the router chassis is electrically connected to earth ground.
■Wear an ESD-preventive wrist strap, and make sure that it makes good contact with your skin.
■Connect the wrist strap clip to an unpainted portion of the chassis frame to channel unwanted ESD voltages to ground.
Caution: The wrist strap and clip must be used correctly to ensure proper ESD protection. Periodically confirm that the resistance value of the ESD-preventive wrist strap is between 1 and 10 megohms (Mohm).
■If no wrist strap is available, ground yourself by touching the metal part of the router chassis.
The following maintenance guidelines apply to the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs:
■Keep the router chassis area clear and dust-free during and after installation.
■If you remove the chassis cover for any reason, store it in a safe place.
■Do not perform any action that creates a hazard to people or makes equipment unsafe.
■Keep walk areas clear to prevent falls or damage to equipment.
■Follow installation and maintenance procedures as documented by Cisco Systems, Inc.
The following safety warning statements apply to all hardware procedures involving the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs for Cisco 4000 Series Integrated Services Routers. Translations of these warnings are available in the Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information document, which ships with all individual Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs orders, and is also available online.
Warning: IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning: Read the installation instructions before connecting the system to the power source. Statement 1004
Warning: This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028
Warning: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
Warning: Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
Warning: Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036
Warning: Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037
Warning: Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038
Warning: To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039
Warning: Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040
Warning: When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046
The following warnings apply in Australia:
Warning: Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43
Warning: Because invisible laser radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 125
Warning: Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001
Warning: To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Both LAN and WAN ports may use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning: Hazardous network voltages are present in WAN ports regardless of whether power to the router is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the router first. Statement 1026
Warning: Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041
Warning: The telecommunications lines must be disconnected 1) before unplugging the main power connector and/or 2) while the housing is open. Statement 1043
Figure 1 shows the front panel of the Cisco 1-port GE NIM, and Figure 2 shows the front panel of the 2-port GE NIM.
The LEDs for each port can be located at the top or bottom depending on the orientation of the port. The EN/SFP LED is a bi-color LED, and the RJ45 LED is a single-color LED.
Figure 1 1-Port GE Network Interface Module: Front Panel
Figure 2 2-Port GE Network Interface Module: Front Panel
Note: The SKU for this product is identified by combining the three letters on the left side of the face plate “NIM”, followed by a dash “-”, and then followed by the remaining product identification on the right. For example, NIM-1GE-CPU-SFP or NIM-2GE-CU-SFP.
The NIMs have an Enable LED which is mounted on the NIMs and visible through the faceplate of the NIMs on the bottom left. The requirements for the LED include:
Each Small Form-Factor Pluggable (SFP) port has two bi-color LEDs to indicate the status. These LEDs are mounted on the NIM boards.
Each RJ45 port has two single LEDs to indicate the status. These LEDs are embedded within the MAGJACK RJ45.
This section describes the following installation tasks for Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs.
■Tools and Equipment Required During Installation
■Installing a Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs in the Cisco 4000 Series Integrated Services Routers
■Removing a Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs from the Cisco 4000 Series Integrated Services Routers
You will need the following tools and equipment while working with the Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs:
■Number 1 Phillips screwdriver or a small flat-blade screwdriver
Warning: No user-serviceable parts inside. Do not open. Statement 1073
Warning: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
1. Shut down the electrical power to the slot in the router either by turning off the electrical power to the router or by issuing the online insertion and removal (OIR) commands. Leave the power cable plugged in to channel ESD voltages to ground. For more information on OIR, see the “Managing Cisco Enhanced Services and Network Interface Modules” chapter in the Software Configuration Guide for the Cisco 4451-X Integrated Services Router.
2. Remove all network cables, including telephone cables, from the rear panel of the router.
3. Remove the blank faceplates installed over the network interface module slot that you intend to use.
Note: Save blank faceplates for future use.
4. Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the router.
5. Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
6. Using a number 1 Phillips or flat-blade screwdriver, tighten the captive screws on the network interface module.
7. Connect the module to the network and re-enable the power to the slot in the router.
Note: See the Related Documents for information on locating additional hardware documentation.
1. Shut down the electrical power to the slot in the router either by turning off the electrical power to the router or by issuing the online insertion and removal (OIR) commands. Leave the power cable plugged in to channel ESD voltages to ground. For more information on OIR, see the “Managing Cisco Enhanced Services and Network Interface Modules” chapter in the Software Configuration Guide for the Cisco 4000 Series Integrated Services Router.
Note: You cannot shutdown the electrical power if the slot is empty.
2. Remove all network cables, including telephone cables, from the rear panel of the router.
3. Using a number 1 Phillips or flat-blade screwdriver, loosen the captive screws on the network interface module.
4. Slide the network interface module out.
5. If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
Hardware Installation Guide for the Cisco 4451-X Integrated Services Router |
|
Information on configuring Cisco 4451-X Integrated Services Routers |
Software Configuration Guide for the Cisco 4451-X Integrated Services Router |
Information on configuring Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs |
Configuring the Cisco 1GE-CU-SFP and 2GE-CU-SFP Network Interface Modules in Cisco 4000 Series Integrated Services Routers |
Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information |
The Cisco 1GE-CU-SFP and 2GE-CU-SFP NIMs can also be installed on the Cisco 4000 Series Routers using the Cisco SM-X-NIM-ADPTR adapter card. For details, see Connecting the Cisco Network Interface Module Adapter for SM-X Slot on the Cisco 4300 and 4400 Integrated Services Routers.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.