Cisco ONS 15454 SDH TL1 Command Guide, Release 7.0
Chapter 10, DLT Commands
Downloads: This chapterpdf (PDF - 318.0KB) The complete bookPDF (PDF - 11.48MB) | Feedback

DLT Commands

Table Of Contents

DLT Commands

10.1  DLT-<MOD1PAYLOAD>

10.2  DLT-<MOD_RING>

10.3  DLT-BULKROLL<STM_TYPE>

10.4  DLT-CRS-<PATH>

10.5  DLT-EQPT

10.6  DLT-FFP-<MOD2DWDMPAYLOAD>

10.7  DLT-FFP-<STM_TYPE>

10.8  DLT-LNK

10.9  DLT-LNKTERM

10.10  DLT-OCHCC

10.11  DLT-OCHNC

10.12  DLT-OSC

10.13  DLT-RMONTH-<MOD2_RMON>

10.14  DLT-ROLL-<MOD_PATH>

10.15  DLT-ROUTE

10.16  DLT-ROUTE-GRE

10.17  DLT-TADRMAP

10.18  DLT-TRAPTABLE

10.19  DLT-TUNNEL-FIREWALL

10.20  DLT-TUNNEL-PROXY

10.21  DLT-USER-SECU

10.22  DLT-VCG


DLT Commands


This chapter provides DLT (delete) commands for the Cisco ONS 15454 SDH.

10.1  DLT-<MOD1PAYLOAD>

Delete (10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, EC1, ESCON, ETRCLO, GIGE, HDTV, ISC3PEER1G, ISC3PEER2G, ISC3PEER2R, ISCCOMPAT, STM4, STM64, STM1, STM16, T3)

Usage Guidelines

See Table 27-1 for supported modifiers by platform.

This command deletes the specified port.

Category

Ports

Security

Provisioning

Input Format

DLT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Input Example

DLT-GIGE:TID:FAC-5-1:1;

Input Parameters

Parameter and Values
Description

AID

Access identifier from the "FACILITY" section


10.2  DLT-<MOD_RING>

Delete (MS-SPRing)

Usage Guidelines

This command deletes the multiplex section-shared protection ring (MS-SPRing) of the NE.

The following actions will return error messages:

If the system fails on getting IOR a SROG (Status, Get IOR Failed) error message is returned.

If the AID is invalid, an IIAC (Invalid AID) error message is returned.

If the BLSR does not exist, a SRQN (MSSPR Does Not Exist) error message is returned.

The SROF (Facility Not Provisioned) or (Cannot Access MSSPR) error message is returned for an invalid query.

If the MS-SPRing is in use, a SROF (MSSPR In Use) error message is returned.

The SRQN (MSSPR Deletion Failed) error message is returned for an invalid deletion query.


Note The ALL AID is invalid for this command.



Note The list AID format is supported in this release (R7.0).


Category

MS-SPRing

Security

Provisioning

Input Format

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-MSSPR:PETALUMA:MSSPR-2:123;

Input Parameters

Parameter and Values
Description

AID

Access identifier from the "AidUnionId1" section. Identifies the MS-SPRing of the NE. ALL or MSSPR-ALL AID is not allowed for editing MS-SPRing


10.3  DLT-BULKROLL<STM_TYPE>

Delete Bulkroll (STM4, STM64, STM1, STM16)

Usage Guidelines

This command deletes an attempted bulk rolling operation of a facility or completes an attempted rolling operation. This command is used for bulk line level rolling. Use DLT-ROLL-<MOD_PATH> for single path level rolling.

See Table 27-1 for supported modifiers by platform.

Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],WHY=<WHY>;

Input Example

DLT-BULKROLL-STM4:CISCO:FAC-1-1:6:::RFROMSTART=VC4-1-1-1,
RFROMEND=VC4-1-1-11,WHY=STOP;

Input Parameters

Parameter and Values
Description

FROM

One of the end points. Access identifier from the "FACILITY" section for line level rolling and bulk rolling

RFROMSTART

The starting time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11)

RFROMEND

The ending time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (VC or VC11)

WHY

The reason for deletion

Parameter type is WHY—reason for deletion

END

Drop the leg to be rolled. The leg that is identified by the RFROM in ENT-ROLL/ENT-BULKROLL

STOP

The rolling operation will be aborted and reverted to the previous configuration


10.4  DLT-CRS-<PATH>

Delete Cross-Connection (VC3, VC44C, VC38C, VC464C, VC48C, VC36C, VC4, VC416C, VC42C, VC43C, VC12)

Usage Guidelines

See Table 27-1 for supported modifiers by platform.

This command deletes a cross-connection between VC paths. VC paths are specified using their VC AID.


NoteThe fields after CTAG (trailing colons) are optional.

For the 1-way cross-connections, the AIDs must be in the same order as originally entered; for the 2-way cross-connections, either order will work.

This command does not support deleting multiple VC cross-connections.

Using "&" in the AID field of this command can delete an subnetwork connection protection (SNCP) virtual container (VC) cross-connection.

The following command is used to delete a 1-way selector or 2-way selector and bridge with:

from points: F1, F2

to point: T1

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1:<CTAG>;

The following command is used to delete a 1-way bridge or 2-way selector and bridge with:

from point: F1

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1,T1&T2:<CTAG>;

The following command is used to delete a 1-way or 2-way subtending SNCP connection with:

from points: F1, F2

to points: T1, T2

DLT-CRS-{VC_PATH}:[<TID>]:F1&F2,T1&T2:<CTAG>;

The AID format in the deletion command is the same as the AID format in the retrieved response message. For example, if the output of any retrieved AID is "F1&F2,T1:CCT,VC4", the deletion command with the AID format F1&F2,T1 is required to delete this cross-connection.

The following command is used to delete a SNCP IDRI cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C&D:<CTAG>;

A-Path on ring X to which traffic from ring Y is bridged

B-Path on ring X to which traffic from the same ring is bridged

C-Path on ring Y to which traffic from ring X is bridged

D-Path on ring Y to which traffic from the same ring is bridged

A, B, C, and D have a positional meaning. Connection type 2WAYDC is used for SNCP IDRI cross-connections.

The following command is used to delete a SNCP dual-ring interconnect (DRI) cross-connection:

DLT-CRS-{VC_PATH}:[<TID>]:A&B,C:<CTAG>;

A-Path on ring X to which traffic from ring Y is bridged

B-Path on ring X to which traffic from the same ring is bridged

C-Traffic to and from ring Y

A, B, and C have a positional meaning. Connection type 2WAYDC is used for SNCP DRI cross-connections.

All A&B AIDs in the TL1 cross-connection command are in the format of WorkingAID&ProtectAID.

You can experience some implementation behavior problems if additional drops have been added to the connection object.

The facility AID is only valid for slots holding the G1K-4 card.

The virtual facility AID (VFAC) is only valid on slots holding an ML-Series card.

CKTID is a string of ASCII characters. The maximum length of CKTID can be 48 characters. If the CKTID is EMPTY or NULL, the field will not appear.


Category

Cross Connections

Security

Provisioning

Input Format

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>];

Input Example

DLT-CRS-VC44C:VINBURG:VC4-1-1-1,VC4-12-1-1:102:::CKTID=CKTID,CMDMDE=CMDMDE;

Input Parameters

Parameter and Values
Description

SRC

Source AID from the "CrossConnectId1" section

DST

Destination AID from the "CrossConnectId1" section

CKTID

String

CMDMDE

Command Mode. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect from Unlocked-Enabled or Locked-Disabled,AutomaticInService service states

Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied

FRCD

Force the system to override a state where the command would normally be denied

NORM

Execute the command normally. Do not override any conditions that might make the command fail


10.5  DLT-EQPT

Delete Equipment

Usage Guidelines

This command deletes a card from the NE.

This command removes the card type and attributes that were entered for a particular slot. If any facilities are assigned, they are deleted too. The command will be denied if the card is part of a protection group or has a cross-connect endpoint.

The DLT-EQPT command also deletes a shelf that is no longer used. A shelf can only be deleted if there is no equipment present or if the equipment and it's attributes are not in use and can be deleted as well. Only one REPT-DBCHG on SHELF-{1-8} will be reported in the latter case. The node controller shelf (the shelf whose shelf ID is 1) cannot be deleted.

To delete a card that is part of a protection group, it has to be removed from the protection group first using the ED-EQPT command.

Error conditions for deleting equipment can be:

The error message SPLD (Equipment In Use) will be returned in the following conditions:

The card is in a protection group

The card has a cross-connection or a DCC/GCC/OSC termination, or provisionable patchcord termination.

If any of its facilities are being used as a synchronization source.


Note If a card is not provisioned, an error message will be returned.


Category

Equipment

Security

Provisioning

Input Parameters

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::];

Input Example

DLT-EQPT:SONOMA:SLOT-1:104;

Input Parameters

Parameter and Values
Description

AID

Access identifier from the "EQPT" section. Identifies an equipment unit (slot) to act on


10.6  DLT-FFP-<MOD2DWDMPAYLOAD>

Delete Facility Protection Group (10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, ISC1, ISC3, PASSTHRU)

Usage Guidelines

This command deletes Y-cable protection on client facilities.

Category

DWDM

Security

Provisioning

Input Format

DLT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,<DST>:<CTAG>[:::];

Input Example

DLT-FFP-HDTV:CISCO:FAC-1-1-1,FAC-2-1-1:100;

Input Parameters

Parameter and Values
Description

SRC

Source AID from the "FACILITY" section

DST

Destination AID from the "FACILITY" section


10.7  DLT-FFP-<STM_TYPE>

Delete Facility Protection Group (STM4, STM64, STM1, STM16)

Usage Guidelines

See Table 27-1 for supported modifiers by platform.

This command deletes an synchronous transfer mode (STM) facility protection group in a 1+1 architecture.


Note If the protection group does not exist, an error message will be returned.


Category

Protection

Security

Provisioning

Input Format

DLT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::];

Input Example

DLT-FFP-STM1:PETALUMA:FAC-2-1,FAC-1-1:1;

Input Parameters

Parameter and Values
Description

WORK

The working facility AID from the "FACILITY" section

PROTECT

The protect facility AID from the "FACILITY" section


10.8  DLT-LNK

Delete Optical Link (OCH, OMS, OTS)

Usage Guidelines

This command deletes an optical link between two optical connection points. Optical link is specified by using the AID of the involved optical connection points.

Category

DWDM

Security

Provisioning

Input Format

DLT-LNK:[<TID>]:<FROM>,<TO>:<CTAG>;

Input Example

DLT-LNK:PENNGROVE:BAND-6-1-TX,BAND-13-1-RX:114;

Input Parameters

Parameter and Values
Description

FROM

The identifier at one end of the optical link from the AID "BAND" section

TO

The identifier at the other end of the optical link from the AID "BAND" section


10.9  DLT-LNKTERM

Delete a Provisionable Patchcord Termination

Usage Guidelines

This command deletes a provisionable patchcord termination present on a node. All termination points of a link/provisionable patchcord have to be deleted for the link to be deleted fully.


Note This command accepts multiple AIDs, but does not accept the ALL AID.



Note A suitable error will be returned if the link termination does not exist.


Category

Provisionable Patchcords

Security

Provisioning

Input Format

DLT-LNKTERM:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-LNKTERM::LNKTERM-1:CTAG;

Input Parameters

Parameter and Values
Description

AID

Access identifier from the "LNKTERM" section. Indicates a link (provisionable patchcord) termination on the local node.


10.10  DLT-OCHCC

The Delete Optical Channel Client Connection (DLT-OCHCC) command deletes the OCH client connection.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHCC:VA454-22:FAC-2-1-1:116:::CKTID=\"OCHCC-1\",CMDMDE=FRCD;

Input Parameters

AID

Access identifier from the "FACILITY" section.

CKTID

Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null the CKTID field will not be displayed.

CMDMDE

The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.


10.11  DLT-OCHNC

(Cisco ONS 15454) The Delete Optical Channel Network Connection (DLT-OCHNC) command deletes the OCH network connection.

Usage Guidelines

Two network connection channel endpoints must be specified in order to identify the wavelength channel inside the node.

Category

DWDM

Security

Provisioning

Input Format

DLT-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>],[CMDMDE=<CMDMDE>];

Input Example

DLT-OCHNC:VA454-22:CHANWL-1-3-TX-1530.33,
CHANWL-4-1-RX-1530.33:116:::CKTID=CIRCUIT,CMDMDE=FRCD;

Input Parameters

SRC

Source access identifier from the "CHANNEL" section. In 2-way wavelength connection sources both directions need to be indicated.

DST

Destination access identifier from the "LINEWL" section. In 2-way wavelength connection sources both directions need to be indicated.

CKTID

Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null the CKTID field will not be displayed.

CMDMDE

The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.

FRCD

Force the system to override a state in which the command would normally be denied.

NORM

Execute the command normally. Do not override any conditions that may make the command fail.


10.12  DLT-OSC

Delete Optical Service Channel

Usage Guidelines

This command deletes the OSC group of the NE.

Category

DWDM

Security

Provisioning

Input Format

DLT-OSC:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-OSC:PENNGROVE:OSC-1:114;

Input Parameters

AID

Access identifier from the "OSC" section. Identifies the OSC group of the NE


10.13  DLT-RMONTH-<MOD2_RMON>

Delete Remote Monitoring Threshold (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 4GFC, 4GFICON, FSTE, G1000, GFPOS, GIGE, OCH, POS)

Usage Guidelines

This command deletes a threshold entry in the remote monitoring (RMON) alarm table. Because there can be multiple thresholds created for a particular montype, you must specify all the necessary parameters for the specific threshold you want to delete.

See Table 27-1 for supported modifiers by platform.

The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.

Category

Performance

Security

Provisioning

Input Format

DLT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,<INTVL>:
RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE],[STARTUP=<STARTUP>][:];

Input Example

DLT-RMONTH-GIGE:CISCO:FAC-2-1:1234::ETHERSTATSOCTETS,,,,100:RISE=1000,FALL=100
SAMPLE=DELTA,STARTUP=RISING;

Input Parameters

SRC

Source access identifier from the "FACILITY" section. AID for the facility that manages the data statistics

MONTYPE

Monitored type. Type of RMON monitored data statistics

Parameter type is ALL_MONTYPE—monitoring type list

AISSP

Alarm Indication Signal SecondsPath

ALL

All possible values

BBEP

SDH Background Block Errors Path

BBE-PM

OTN—Background Block Errors—Path Monitor Point

BBER

SDH Background Block Error Ratio

BBER-PM

OTN—Background Block Error Ratio—Path Monitor Point expressed as 1/10th of a percentage.

BBER-SM

OTN—Background Block Error Ratio—Section Monitor Point expressed as 1/10th of a percentage.

BBE-SM

OTN—Background Block Errors—Section Monitor Point

BIEC

FEC—Bit Errors Corrected

CGV

8B10B—Code Group Violations

CVCPP

Coding Violations—CP-Bit Path

CVL

Coding Violations—Line

CVP

Coding Violations—Path

CVS

Coding Violations—Section

CVV

Coding Violations—Section

DCG

8B10B—Data Code Groups

ESCPP

Errored Seconds—CPBit Path

ESL

Errored Seconds—Line

ESP

Errored Seconds—Path

ES-PM

OTN—Errored Seconds—Path Monitor Point

ESR

Errored Second—Ratio

ESR-PM

Errored Seconds Ratio—Path monitor Point expressed as 1/10th of a percentage

ESR-SM

Errored Seconds Ratio—Section monitor Point expressed as 1/10th of a percentage

ESS

Errored Seconds—Section

ES-SM

OTN—Errored Seconds—Section Monitor Point

ESV

Errored Seconds—VC Path

etherStatsBroadcastPkts

The total number of good packets received that were directed to a multicast address

etherStatsCollisions

Number of transmit packets that are collisions

etherStatsCRCAlignErrors

The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets

etherStatsDropEvents

Number of received frames dropped at the port level

etherStatsFragments

The total number of packets received that were less than 64 octets

etherStatsJabbers

The total number of packets received that are longer than 1518 octets

etherStatsOctets

The total number of octets of data

etherStatsOversizePkts

The total number of packets received that are longer than 1518 octets

etherStatsPkts

The total number of packets (including bad packets, broadcast packets, and multicast packets) received

etherStatsUndersizePkts

The total number of packets received that are less than 64 octets

FCP

Failure Count—Line

FC-PM

OTN—Failure Count—Path Monitor Point

FC-SM

OTN—Failure Count—Section Monitor Point

HP-AR

Availability Ratio

HP-BBE

High-Order Path Background Block Error

HP-BBER

High-Order Path Background Block Error Ratio

HP-EB

High-Order Path Errored Block

HP-ES

High-Order Path Errored Second

HP-ESA

High-Order Path Errored Seconds - A

HP-ESB

High-Order Path Errored Seconds - B

HP-ESR

High-Order Path Errored Second Ratio

HP-FC

High-Order Path Failure Count

HP-NPJC-PDET

High Order Path Negative Pointer Justification Count

HP-NPJC-PGEN

High Order Path Pointer Justification Count Seconds

HP-OI

Outage Intensity

HP-PJCDIFF

High Order Path Pointer Justification Count Difference

HP-PJCS-PDET

High Order Path Pointer Justification Count

HP-PPJC-PDET

High Order Path Positive Pointer Justification Count

HP-PPJC-PGEN

High Order Path, Positive Pointer Justification Count

HP-SEPI

The number of SEP events in available time

HP-SES

High-Order Path Severely Errored Seconds

HP-SESR

High-Order Path Severely Errored Second Ratio

HP-UAS

High-Order Path Unavailable Seconds

ifInBroadcastPkts

Number of broadcast packets received since the last counter reset

ifInDiscards

The number of inbound packets

ifInErrorBytePktss

Receive Error Byte

ifInErrors

The number of inbound packets (or transmission units) that contained errors

ifInFramingErrorPkts

Receive Framing Error

ifInJunkInterPkts

Receive Interpacket Junk

ifInMulticastPkts

Number of multicast packets received since the last counter reset

ifInOctets

Number of bytes transmitted since the last counter reset

ifInUcastPkts

Number of unicast packets received since the last counter reset

ifOutBroadcastPkts

Number of broadcast packets transmitted

ifOutDiscards

The number of outbound packets

ifOutErrors

The number of outbound packets (or transmission units) that could not be transmitted because of errors

ifOutMulticastPkts

Number of multicast packets transmitted

ifOutPayloadCrcErrors

Received payload cyclic redundancy check (CRC) errors

ifOutUcastPkts

Number of unicast packets transmitted

IOS

8B10B- Idle Ordered Sets

IPC

Invalid Packet Count

LBCL-AVG

Average Laser Bias current in micro A

LBCL-MAX

Maximum Laser Bias current in micro A

LBCL-MIN

Minimum Laser Bias current in micro A

LBCN

Normalized Laser Bias Current for STM1-8

LBCN-HWT

Laser bias current

LBCN-LWT

Laser bias current

LOSSL

Loss of Signal Seconds—Line

LP-BBE

Low-Order Path Background Block Error

LP-BBER

Low-Order Path Background Block Error Ratio

LP-EB

Low-Order Path Errored Block

LP-ES

Low-Order Path Errored Second

LP-ESA

Low-Order Path Errored Seconds - A

LP-ESB

Low-Order Path Errored Seconds - B

LP-ESR

Low-Order Path Errored Second Ratio

LP-FC

Low-Order Path Failure Count

LP-NPJC-DET

Low Order Negative Pointer Justification Count, Detected

LP-NPJC-GEN

Low Order Negative Pointer Justification Count, Generated

LP-PPJC-DET

Low Order Positive Pointer Justification Count, Detected

LP-PPJC-GEN

Low Order positive Pointer Justification Count, Generated

LP-SEP

A sequence of between 3 to 9 consecutive severely errored seconds (SES)

LP-SEPI

Low-Order Path Severely Errored Period Intensity

LP-SES

Low-Order Path Severely Errored Seconds

LP-UAS

Low-Order Path Unavailable Seconds

MS-PSC

Protection switch count

MS-PSD

Protection switch duration

NIOS

8B10B—Non Idle Ordered Sets

NPJC-PDET

Negative Pointer Justification, Path Detected

NPJC-PGEN

Negative Pointer Justification, Path Detected

OPR-AVG

Average Receive Power in 1/10 micro W

OPR-MAX

Maximum Receive Power in 1/10 micro W

OPR-MIN

Minimum Receive Power in 1/10 micro W

OPRN

Normalized Optical Receive Power for STM1-8

OPRN-MAX

Maximum value for OPRN

OPRN-MIN

Minimum value for OPRN

OPT-AVG

Average Transmit Power in 1/10 uW

OPT-MAX

Maximum Transmit Power in 1/10 uW

OPT-MIN

Minimum Transmit Power in 1/10uW

OPTN

Normalized value for Optical Power Transmitted for STM1-8 card

OPTN-MAX

Maximum value for OPTN

OPTN-MIN

Minimum value for OPTN

OPWR-AVG

Optical Power—Average Interval Value in 1/10th of dBm

OPWR-MAX

Optical Power—Maximum Interval Value in 1/10th of dBm

OPWR-MIN

Optical Power—Minimum Interval Value in 1/10th of dBm

PPJC-PDET

Positive Pointer Justification, Path Detected

PPJC-PGEN

Positive Pointer Justification, Path Detected

PSC

Protection Switching Count

PSC-R

Protection Switching Count—Ring

PSC-S

Protection Switching Count—Span

PSC-W

Protection Switching Count—Working

PSD

Protection Switching Duration

PSD-R

Protection Switching Duration—Ring

PSD-S

Protection Switching Duration—Span

PSD-W

Protection Switching Duration—Working

SASCPP

Severely Errored Framing/AIS Second—CP-Bit Path

SASP

Severely Errored Framing/AIS Seconds Path

SEFS

Severely Errored Framing Seconds

SESCPP

Severely Errored Second—CP-Bit Path

SESL

Severely Errored Second—Line

SESP

Severely Errored Second—Path

SES-PM

OTN—Severely Errored Second—Path

SESR

Severely Errored Second—Ratio

SESR-PM

OTN—Severely Errored Second Ratio—Path Monitor Point expressed as 1/10th of a percentage

SESR-SM

OTN—Severely Errored Second Ratio—Section Monitor Point expressed as 1/10th of a percentage

SESS

Severely Errored Second—Section

SES-SM

OTN—Severely Errored Second—Section Monitor Point

SESV

Severely Errored Second—VC Path

UASCPP

Unavailable Second—CP-Bit Path

UASL

Unavailable Second—Line

UASP

Unavailable Second—Path

UAS-PM

OTN—Unavailable Second—Path Monitor Point

UAS-SM

OTN—Unavailable Second—Section Monitor Point

UASV

Unavailable Second—VC Path

UNC-WORDS

FEC—Uncorrectable Words

VPC

Valid Packet Count

INTVL

The interval in seconds over which the data is sampled and compared with the rising and falling threshold. A valid value is any integer larger than or equal to 10 (seconds)

RISE

The rising threshold for the sampled statistics. A valid value is any integer

FALL

The falling threshold. A valid value is any integer smaller than the rising threshold

SAMPLE

The method of calculating the value to be compared to the thresholds

Parameter type is SAMPLE_TYPE—describes how the data will be calculated during the sampling period

ABSOLUTE

Comparing directly

DELTA

Comparing with the current value of the selected variable subtracted by the last sample

STARTUP

Dictates whether an event will generate if the first valid sample is greater than or equal to the rising threshold, less than or equal to the falling threshold, or both

Parameter type is STARTUP_TYPE—indicates whether an event will be generated when the first valid sample is crossing the rising or falling threshold

FALLING

Generates the event when the sample is smaller than or equal to the falling threshold

RISING

Generates the event when the sample is greater than or equal to the rising threshold

RISING-OR-FALLING

Generates the event when the sample is crossing the rising threshold, or the falling threshold


10.14  DLT-ROLL-<MOD_PATH>

Delete Roll (VC44C, VC464C, VC48C, VC4, VC416C, VC42C, VC43C)

Usage Guidelines

This command deletes or completes an attempted rolling operation of a facility or completes an attempted rolling operation.

See Table 27-1 for supported modifiers by platform.


Note VC11, VC12 and VC3 are not supported for this command in this release.


Category

Bridge and Roll

Security

Provisioning

Input Format

DLT-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::WHY=<WHY>;

Input Example

DLT-ROLL-VC4:CISCO:VC4-1-1-1,VC4-2-1-1:6:::WHY=STOP;

Input Parameters

FROM

Source access identifier from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the FROM-AID termination point. Otherwise, FROM is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters

TO

Destination AID from the "VC" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, the termination point (leg) should be the TO-AID termination point. Otherwise, the TO is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters

WHY

The reason for deletion

Parameter type is WHY—reason for deletion

END

Drop the leg to be rolled; the leg that is identified by the RFROM in the ENT-ROLL command

STOP

The rolling operation will be deleted and reverted to the previous configuration


10.15  DLT-ROUTE

Delete Route

Usage Guidelines

This command deletes static routes.

Category

System

Security

Provisioning

Input Format

DLT-ROUTE:[<TID>]::<CTAG>::<DESPID>;

Input Example

DLT-ROUTE:CISCO::123::10.64.72.57;

Input Parameters

Parameter and Values
Description

DESPID

Destination IP. String


10.16  DLT-ROUTE-GRE

Delete Route Generic Routing Encapsulation

Usage Guidelines

This command deletes a GRE tunnel.

Category

System

Security

Provisioning

Input Format

DLT-ROUTE-GRE:[<TID>]::<CTAG>:::IPADDR=<IPADDR>,
IPMASK=<IPMASK>,NSAP=<NSAP>;

Input Example

DLT-ROUTE-GRE:CISCO::123:::IPADDR=10.64.72.57,IPMASK=255.255.255.0,
NSAP=39840F80FFFFFF0000DDDDAA000010CFB4910200;

Input Parameters

Parameter and Values
Description

IPADDR

IP address of the tunnel endpoint. String

IPMASK

Subnet mask for the tunnel endpoint. String

NSAP

Network Service Access Port (NSAP) address for the tunnel endpoint. String


10.17  DLT-TADRMAP

Delete TID Address Mapping

Usage Guidelines

This command instructs a gateway NE to delete an entry in the TADRMAP table.

Category

System

Security

Provisioning

Input Format

DLT-TADRMAP:[<TID>]::<CTAG>:::[TIDNAME=<TIDNAME>],[ADDRTYPE=<ADDRTYPE>];

Input Example

DLT-TADRMAP:TID::CTAG:::TIDNAME=ENENODENAME,ADDRTYPE=IPADDR;

Input Parameters

Parameter and Values
Description

TIDNAME

TID of the entity to be removed from the TADRMAP. String

ADDRTYPE

Specifies either to remove and IP, NSAP or IP-AND-NSAP entry in the TADRMAP

Parameter type is ADDRTYPE—specifies whether the address is and IP address or an NSAP address

IP

IP address

IP-AND-NSAP

IP and NSAP address

NSAP

NSAP address


10.18  DLT-TRAPTABLE

Delete Trap Table

Usage Guidelines

This command deletes an SNMP trap destination entry. Entering ALL will delete the whole table.

Category

System

Security

Provisioning

Input Format

DLT-TRAPTABLE:[<TID>]:<AID>:<CTAG>;

Input Example

DLT-TRAPTABLE::1.2.3.4:1;

Input Parameters

Parameter and Values
Description

AID

Access identifier from the "IPADDR" section. IP address identifies the trap destination. Only numeric IP addresses are allowed


10.19  DLT-TUNNEL-FIREWALL

Delete Tunnel Firewall

Usage Guidelines

This command deletes a firewall tunnel.

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-FIREWALL:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-FIREWALL:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Input Parameters

Parameter and Values
Description

SRCADDR

Source IP address. String

SRCMASK

Source mask. String

DESTADDR

Destination IP address. String

DESTMASK

Destination mask. String


10.20  DLT-TUNNEL-PROXY

Delete Tunnel Proxy

Usage Guidelines

This command deletes a proxy tunnel.

Category

System

Security

Provisioning

Input Format

DLT-TUNNEL-PROXY:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>],
[SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>];

Input Example

DLT-TUNNEL-PROXY:TID::CTAG:::SRCADDR=192.168.100.52,
SRCMASK=255.255.255.0,DESTADDR=192.168.101.14,DESTMASK=255.255.255.0;

Input Parameters

Parameter and Values
Description

SRCADDR

Source IP address. String

SRCMASK

Source mask. String

DESTADDR

Destination IP address. String

DESTMASK

Destination mask. String


10.21  DLT-USER-SECU

Delete User Security

Usage Guidelines

This command deletes a user and can only be performed by a Superuser. Privilege levels are described in the ENT-USER-SECU command.

This command cannot be used to delete a user that is currently logged on.

For the DLT-USER-SECU command:

DLT-USER-SECU:[TID]:<UID>:[CTAG];

the syntax of <UID> is not checked. The user is deleted if the <UID> exists in the database.

Category

Security

Security

Superuser

Input Format

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>;

Input Example

DLT-USER-SECU:PETALUMA:CISCO15:123;

Input Parameters

Parameter and Values
Description

UID

User identifier. Can be up to 10 alphanumeric characters. String


10.22  DLT-VCG

Delete Virtual Concatenated Group

Usage Guidelines

This command deletes a VCG object.

Category

VCAT

Security

Provisioning

Input Format

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:];

Input Example

DLT-VCG:NODE1:FAC-1-1:1234:::CMDMDE=FRCD;

Input Parameters

Parameter and Values
Description

SRC

Source AID from the "FACILITY" section. ML-Series cards use VFAC AID and FC_MR-4 cards use FAC AID

CMDMDE

Command execution mode, forced or normal. Forced (FRCD) deletes all the VCG members and member cross-connects of a VCG

Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied

FRCD

Force the system to override a state where the command would normally be denied

NORM

Execute the command normally. Do not override any conditions that might make the command fail