The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter provides TL1 error information supported by the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL. For alarm information, Refer to the platform-specific Cisco ONS Procedure Guide, Cisco ONS Troubleshooting Guide and Cisco ONS Reference Manual.
Errors can be generated by any command or command response message. Table 3-1 through Table 3-64 list errors alphabetically by error code. The format of an error message is as follows:
SID DATE TIME
M CTAG DENY
<ERRCDE>
/* <ERRMSG> */
;
|
---|
Extra Datablock |
Extra parameters |
Invalid AID Block. Extra Datablock |
Invalid Payload Block. Extra Datablock |
|
---|
Data Missing |
Loopback Type Missing |
Missing Internal Data |
|
---|
Invalid Correlation Tag |
|
---|
Invalid AID Block. Invalid Data Format |
Invalid Data Format |
Invalid Password |
Invalid Payload Block. Invalid Data Format |
Invalid User ID |
|
---|
Input, Garbage |
Invalid AID Block. Extraneous ',' Found |
|
---|
GNE: Input, Invalid Target Identifier |
Input, Invalid Target Identifier |
|
---|
Duplicate N/V field |
Invalid Payload Block. Extra Parameters |
Invalid Payload Block. Extra Parameters |
|
---|
Invalid AID Block. Missing Mandatory Field |
Invalid Payload Block. Missing Mandatory Field |
Invalid syntax |
Missing mandatory field |
|
---|
No Error |
|
---|
Memory Out Of Range |
|
---|
Login Not Active |
|
---|
GNE: All ENE Connections in Use |
Requested DCC In Use |
|
---|
GNE: No Response from ENE - IENE |
|
---|
Software upgrade in progress |
|
---|
Multiservice Slot Out Of Range |
Invalid Slot Number For SDH Electrical Cards |
Invalid Slot Number |
|
---|
Connection In Service |
TAP Already In Use |
TAP Number In Use |
|
---|
Already Allowed |
|
---|
Equipment Already Provisioned |
|
---|
GNE: ENE is down |
TAP Not Connected |
|
---|
Loopback Applied On Cross-connection |
|
---|
Already Inhibited |
|
---|
Port Already In Service |
|
---|
Already In Clear Maintenance State |
Already In Force Maintenance State |
Already In Lockout Maintenance State |
Already In Manual Maintenance State |
|
---|
Control Already Operated |
Control Already Released |
Control Operated In Mntry |
|
---|
Port Already in IS-AINS |
Port Already In OOS-MT |
Port Already Out Of Service |
|
---|
GNE: All Gateways in Use |
System Memory Exhausted. Retry A Few Seconds Later |
|
---|
Duplex Unit Locked |
|
---|
Active TCC Not Ready |
Standby TCC Not Ready |
|
---|
Cross connection does not exist |
Path Roll Does Not Exist |
Replace This Message When A SNCC message is needed |
|
---|
Reference Not From Optical Card |
|
---|
Cannot Get Role Of Port |
Get Port Role Failed |
|
---|
Unrecognized Message Type |
|
---|
Cannot Get Current Card Status |
Protection Unit Failed Or Missing |
Status, Protection Unit Failed or Missing |
|
---|
Cannot Create 1+1 Protection Group |
Cannot Delete Equipment |
Equipment In Use |
FTP Task Is Busy |
Facility Is Busy |
Protection Unit Locked |
|
---|
Invalid Connection Type |
Requested Access Configuration is Invalid |
|
---|
Already In Requested Mode |
Area already exists on lan interface |
Cannot use backbone area, lan active |
Requested Condition Already Exists |
|
---|
TAP Not Found |
|
---|
Manual Switch Cannot Override Forced Switch |
Switch Request Denied |
|
---|
Status, Working Unit Failed or Missing |
Working Unit Failed Or Missing |
|
---|
Working Unit Locked |
In order to improve telnet functionality for automated systems, the echo function has been turned off in ONS 15454 Release 3.0 and later. This change is transparent to users running standard UNIX-compliant telnet clients; however, PC users might need to change their client setup to enable "local echo." This is normally accomplished by a drop-down list or a preference attribute.
To test the local echo on your PC client, use the RTRV-HDR command. If you receive a response but no data, set local echo ON. Cisco recommends that you close any windows containing sensitive information after exiting a TL1 session.