Guest

Cisco ONS 15454 Series Multiservice Provisioning Platforms

Cisco ONS 15454 SDH TL1 Command Quick Reference Guide, Release 5.0

  • Viewing Options

  • PDF (1.7 MB)
  • Feedback
Quick Reference

Table Of Contents

Cisco ONS 15454 SDH TL1 Command Quick Reference Guide, Release 5.0

MS-SPRing

Cross Connections

DWDM

Environment

Equipment

Facility

Fault

File Transfer

Log

Network

Paths

Performance

Ports

Protection

Provisionable Patchcords

Security

Synchronization

System

Troubleshooting and Test Access

VCAT


Quick Reference

Cisco ONS 15454 SDH TL1 Command Quick Reference Guide, Release 5.0


This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 SDH, Release 5.0. Refer to the Cisco ONS 15454 SDH TL1 Command Guide, Release 5.0 for a complete description of TL1 commands.

TL1 commands conform to the following syntax:
a:b:c:d:e: ...z;
where:
"a" is the Command Code
"b" is the Target Identifier (TID)
"c" is the Access Identifier (AID) or the User Identifier (UID)
"d" is the Correlation Tag (CTAG)
"e: ...z;" are other positions required for various commands
The TID, AID, and CTAG route and control the TL1 command.
Other parameters provide additional information required to complete the action requested by the command.

1 MS-SPRing

Table 1 MS-SPRing 

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];

Deletes the multiplex section-shared protection ring (MS-SPRing) of the NE.

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>][:];

Edits the MS-SPRing attributes.

ENT-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>,
MODE=<MODE>,[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,]
[SRVTM=<SRVTM>,]EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>,
[EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>];

Creates a MS-SPRing in either 2-fiber or 4-fiber type.

EX-SW-<STM_MSSPR>:[<TID>]:<AID>:<CTAG>::,[<SWITCHTYPE>],[<DIRECTION>];

Exercises the algorithm for switching from a working facility to a protection facility without actually performed a switch.

RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];

Retrieves all of the MS-SPRing information of the network element (NE).

Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>]::[RINGID=<RINGID>,][NODEID=<NODEID>,][MODE=<MODE>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>,]
[EASTWORK=<EASTWORK>,][WESTWORK=<WESTWORK>,][EASTPROT=<EASTPROT>,]
[WESTPROT=<WESTPROT>]"
;

RTRV-TRC-<STM_MSSPR>:[<TID>]:<AID>:<CTAG>;

Retrieves the valid J1 expected trace string, received trace string, trace mode, c2 byte, VC bandwidth of the STM port only if the port has MS-SPring.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][EXPTRC=<EXPTRC>,][INCTRC=<INCTRC>,]
[TRCMODE=<TRCMODE>,][C2=<C2>]"

;


2 Cross Connections

Table 2 Cross Connections 

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>];

Deletes a cross connection between virtual channel (VC) paths.

ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>,][REMOVE=<REMOVE>,]
[CKTID=<CKTID>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits the state of a VC cross-connection.

ENT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::<CCT>:[DRITYPE=<DRITYPE>,]
[DRINODE=<DRINODE>,][CKTID=<CKTID>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Creates a VC cross connection with cross connection types.

RTRV-CRS:[<TID>]:[<AID>]:<CTAG>:::[CRSTYPE=<CRSTYPE>][:];

Retrieves all the cross connections based on the required PATH types.

RTRV-CRS-<PATH>:[<TID>]:<SRC>:<CTAG>[::::];

Retrieves any connections associated with the entered AID(s) or AID range; end information is returned along with the type of connection.


3 DWDM

Table 3 DWDM 

DLT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,<DST>:<CTAG>[:::];

Deletes Y-cable protection on client facilities.

DLT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>;

Deletes an optical link between two optical connection points; optical link is specified by using AID of the involved optical connection points.

DLT-OSC:[<TID>]:<AID>:<CTAG>;

Deletes the optical service channel (OSC) group of the NE.

DLT-WLEN:[<TID>]:<AID>:<CTAG>[:::CMDMDE=<CMDMDE>];

Deletes the provisioned wavelength (WLEN).

ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits the operating parameters for a dense wavelength division multiplexing (DWDM) client facility.

ED-APC:[<TID>]::<CTAG>[:::APCENABLE=<APCENABLE>];

Command is given to the NE to modify the amplification power control (APC) application attributes.

ED-CLNT:[<TID>]:<AID>:<CTAG>:::[NAME=<PORTNAME>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>,][COMM=<COMM>,][MACADDR=<MACADDR>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][RLASER=<RLASER>,]
[SOAK=<SOAK>,][OSPF=<OSPF>,][CMDMDE=<CMDMDE>]:<PST>,[<SST>];

Edits client facility attributes.

ED-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];

Edits Y-cable protection group on client facilities.

ED-FFP-OCH:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];

Changes the provisioning for the default protection group of the DWDM port of a TXP_MR_2.5G or TXPP_MR_2.5G card.

ED-LNK-<MOD2O>:[<TID>]:<FROM>,
<TO>:<CTAG>:::[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits an optical link state.

ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPWLEN=<EXPWLEN>,]
[VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,][SDBER=<SDBER>,]
[COMM=<COMM>,][GCCRATE=<GCCRATE>,][OSDBER=<OSDBER>,][DWRAP=<DWRAP>,]
[FEC=<FEC>,][PAYLOADMAP=<PAYLOADMAP>,][MACADDR=<MACADDR>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][SOAK=<SOAK>,][OSPF=<OSPF>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Used to modify the attributes (that is, service parameters) and state of an optical channel (OCH) facility.

ED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPBAND=<EXPBAND>,]
[VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>,][NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Used to modify the attributes (that is, service parameters) and state of an optical multiplex section (OMS) facility.

ED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>];

Edits the OSC group attributes.

ED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][OFFSET=<OFFSET>,][CALTILT=<CALTILT>,][OSRI=<OSRI>,]
[AMPLMODE=<AMPLMODE>,][CHPOWER=<CHPOWER>,][EXPGAIN=<EXPGAIN>,]
[NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Modifies the attributes (that is, service parameters) and state of an optical transport section (OTS) facility.

ED-SLV-WDMANS:[<TID>]:<AID>:<CTAG>:::[HIGHSLVEXP=<HIGHSLVEXP>,]
[LOWSLVEXP=<LOWSLVEXP>];

Provisions the expected span loss verification.

ED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,][TRCLEVEL=<TRCLEVEL>,][TRCFORMAT=<TRCFORMAT>][:];

Edits trace-related optical channel facilities.

ED-WDMANS:[<TID>]:<AID>:<CTAG>:::[POWERIN=<POWERIN>,]
[POWEROUT=<POWEROUT>,][POWEREXP=<POWEREXP>,][NTWTYPE=<NTWTYPE>];

Modifies the automatic optical node setup (AONS) application attributes.

ED-WLEN:[<TID>]:<AID>:<CTAG>:::[SIZE=<SIZE>,][CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits wavelength provisioning.

ENT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,
<DST>:<CTAG>:::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:];

Creates Y-cable protection on client facilities.

ENT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>::::<PST>,[<SST>];

Creates an optical link between two optical connection points.

ENT-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>,
[EAST=<EAST>,][WEST=<WEST>];

Creates the OSC group of the NE.

ENT-WLEN:[<TID>]:<AID>:<CTAG>::<CCT>:[SIZE=<SIZE>,][CKTID=<CKTID>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Allocates a wavelength.

OPR-APC:[<TID>]::<CTAG>[::::];

Permit the NE's APC application to force regulation of the optical power to the DWDM ring.

OPR-LASER-OTS:[<TID>]:<AID>:<CTAG>;

Instructs a laser to be switched on.

OPR-LNK:[<TID>]::<CTAG>;

Permits the NE's optical link (OLNK) application to calculate all automatic optical links between points that can be univocally identified by the NE.

OPR-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>::<SW>;

Performs a protection switch on the trunk port of a TXPP_MR_2.5G transponder (protect version only).

OPR-SLV-WDMANS:[<TID>]:<AID>:<CTAG>;

Invokes the calculation of the expected span loss verification.

OPR-WDMANS:[<TID>]::<CTAG>;

Permits the NE's AONS application to force a recompute of the value assigned to all variable optical attenuators (VOAs) representing the optical path inside the node.

RLS-LASER-OTS:[<TID>]:<AID>:<CTAG>;

Instructs a laser to be switched off.

RLS-PROTNSW-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>:<CTAG>[::];

Releases the Y-cable protection switch on client facilities.

RLS-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>;

Releases the protection switch on a TXPP_MR_2.5G transponder trunk port (protect version only).

RTRV-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the configuration parameter of a DWDM client.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AIDUNIONID>,<AIDTYPE>::[NAME=<NAME>,][LBCL=<LBCL>,][OPT=<OPT>,]
[OPR=<OPR>]:<PST_PSTQ>,[<SST>]"
;

RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>:: <ALMTHR>[,,::];

Retrieves the alarm threshold values.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>"
;

RTRV-APC:[<TID>]::<CTAG>;

Retrieves the NE's APC application attributes.

Output format:

SID DATE TIME
M CTAG COMPLD
"::[APCENABLE=<APCENABLE>,][APCSTATE=<APCSTATE>]"
;

RTRV-DWDM:[<TID>]:<AID>:<CTAG>;

Retrieves DWDM card-level attributes.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<EQPTTYPE>,<EQUIP>,,[<STATUS>]:[PEERID=<PEERID>,][NAME=<NAME>,]
[TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,]
[CARDNAME=<CARDNAME>,][PWL=<PWL>,][TWL1=<TWL>,][TWL2=<TWL1>,]
[TWL3=<TWL2>,][TWL4=<TWL3>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>:<CTAG>[::::];

Retrieves Y-cable protection on client facilities.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AIDUNIONID>,<AIDUNIONID1>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]"
;

RTRV-FFP-OCH:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the protection group information for the TXP_MR_2.5G or TXPP_MR_2.5G transponder trunk port.

Output format:

SID DATE TIME
M CTAG COMPLD
"<WORK>,<PROTECT>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]"
;

RTRV-LNK:[<TID>]::<CTAG>;

Retrieves all the (optical) links created in the NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"<FROM>,<TO>::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,][RDIRN=<RDIRN>,]
[BAND=<BAND>,][WLEN=<WLEN>]:<PST_PSTQ>,[<SST>]"
;

RTRV-LNK-<MOD2O>:[<TID>]:<AID>:<CTAG>:::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,]
[RDIRN=<RDIRN>];

Retrieves any optical link associated with the entered AID(s) or AID range.

Output format:

SID DATE TIME
M CTAG COMPLD
"<FROM>,<TO>::[OLNKT=<OPTICALLINKTYPE>,][CTYPE=<CREATIONTYPE>,]
[RDIRN=<RDIRN>,][BAND=<BAND>,][WLEN=<WLEN>]:<PST_PSTQ>,[<SST>]"
;

RTRV-NE-APC:[<TID>]:[<AID>]:<CTAG>;

Retrieves the NE's APC application ports involved in node setup regulation.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<MOD>::[MODIFDAT=<MODIFDAT>,][MODIFTM=<MODIFTM>,]
[CHECKDAT=<CHECKDAT>,][CHECKTM=<CHECKTM>]"
;

RTRV-NE-WDMANS:[<TID>]::<CTAG>;

Retrieves the NE's optical node setup (WDMANS) application ports involved in node setup regulation.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[REGULATED=<REGULATED>,][PARAM=<PARAM>]"

;

RTRV-OCH:[<TID>]:<AID>:<CTAG>;

Retrieves the attributes (that is, service parameters) and state of an OCH facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[RDIRN=<RDIRN>,][OPTYPE=<OPTICALPORTTYPE>,]
[OPWR=<POWER>,][EXPWLEN=<EXPWLEN>,][ACTWLEN=<ACTWLEN>,]
[ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,]
[VOAREFPWR=<VOAREFPWR>,][REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,]
[CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][COMM=<COMM>,][GCCRATE=<GCCRATE>,][DWRAP=<DWRAP>,]
[FEC=<FEC>,][PAYLOADMAP=<PAYLOADMAP>,][OSFBER=<OSFBER>,]
[OSDBER=<OSDBER>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,]
[SENDDUS=<SENDDUS>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][OSPF=<OSPF>,]
[LBCL=<LBCL>,][OPT=<OPT>,][OPR=<OPR>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-OMS:[<TID>]:<AID>:<CTAG>;

Retrieves the attributes (that is, service parameters) and state of an OMS facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,]
EXPBAND=<EXPBAND>,[ACTBAND=<ACTBAND>,][ILOSS=<ILOSS>,]
[VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,]
[VOAREFATTN=<VOAREFATTN>,][VOAREFPWR=<VOAREFPWR>,]
[REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][CHPOWER=<CHPOWER>,]
[NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-OPM:[<TID>]:<AID>:<CTAG>;

Retrieves the optical power monitoring parameters present at the OCH layer in a reconfigurable optical add/drop multiplexing (ROADM) node.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[POWEROUT=<POWEROUT>,][POWERADD=<POWERADD>,]
[POWERPT=<POWERPT>]"
;

RTRV-OSC:[<TID>]:<AID>:<CTAG>;

Retrieves all OSC information of the NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[RINGID=<RINGID>,][NODEID=<NODEID>,][EAST=<EAST>,][WEST=<WEST>]"
;

RTRV-OTS:[<TID>]:<AID>:<CTAG>;

Retrieves the attributes (that is, service parameters) and state of an OTS facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,]
[ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,]
[VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,]
[VOAREFPWR=<VOAREFPWR>,][OSRI=<OSRI>,][AMPLMODE=<AMPLMODE>,]
[CHPOWER=<CHPOWER>,][GAIN=<GAIN>,][EXPGAIN=<EXPGAIN>,]
[REFOPWR=<REFOPWR>,][OFFSET=<OFFSET>,][REFTILT=<REFTILT>,]
[CALTILT=<CALTILT>,][ASEOPWR=<ASEOPWR>,][DCULOSS=<DCULOSS>,]
[AWGST=<AWGST>,][HEATST=<HEATST>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>;

Retrieves the protection switch status of a TXPP_MR_2.5G transponder trunk port (protect version only).

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<SW>,<SWTYPE>"
;

RTRV-SLV-WDMANS:[<TID>]:<AID>:<CTAG>;

Retrieves the options provisionable by the ED-SLV-WDMASN command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[HIGHSLVEXP=<HIGHSLVEXP>,][LOWSLVEXP=<LOWSLVEXP>,]
[SLVACT=<SLVACT>,][RESOLUTION=<RESOLUTION>]"
;

RTRV-TRC-OCH:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::];

Retrieves security trace information.

Output format:

SID DATE TIME
M CTAG COMPLD
"<CHANNEL>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,]
[TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,]
[TRCFORMAT=<TRCFORMAT>]"
;

RTRV-WDMANS:[<TID>]:<AID>:<CTAG>;

Retrieves the AONS application attributes.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[POWERIN=<POWERIN>,][POWEROUT=<POWEROUT>,]
[POWEREXP=<POWEREXP>,][NTWTYPE=<NTWTYPE>,]
[OPTICALTYPE=<OPTICALTYPE>,][LASTRUNDAT=<LASTRUNDAT>,]
[LASTRUNTM=<LASTRUNTM>]"
;

RTRV-WLEN:[<TID>]:<aid>:<CTAG>;

Retrieves the WLEN provisioning information.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<CCT>:[SIZE=<SIZE>,][CKTID=<CKTID>]:<PST_PSTQ>,[<SSTQ>]"
;

SET-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<CONDTYPE>,<THLEV>[,,,];

Sets the alarm thresholds on the following cards/ports/channels: MXP_2.5G_10G/TXP_MR_10G, optical service channel, optical amplifier, dispersion compensation units, multiplex/demultiplex and OADM.


4 Environment

Table 4 Environment 

OPR-ACO-ALL:[<TID>]::<CTAG>;
Operates the cut-off of the office audible alarm indications without changing the local alarm indications.

OPR-EXT-CONT:[<TID>]:<AID>:<CTAG>::[<CONTTYPE>],[<DURATION>];

Operates an external control and closes the external control contact.

REPT ALM ENV

Reports a customer defined condition on an environmental alarm input.

Output format:

SID DATE TIME
** ATAG REPT ALM ENV
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]"
;

REPT EVT ENV

Reports a non-alarmed event against an environmental alarm input.

Output format:

SID DATE TIME
A ATAG REPT EVT ENV
"<AID>:<ALMTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]"
;

RLS-EXT-CONT:[<TID>]:<AID>:<CTAG>[::,];

Releases a forced contact state thus returning the control of the contact to an AUTOMATIC control state.

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Retrieves the environmental alarms.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]"
;

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];

Retrieves the attributes associated with an external control.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>]"
;

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>];

Retrieves the attributes associated with an environmental alarm.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]"
;

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>][,,,];

Retrieves the environmental conditions.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],,,,[<DESC>]"
;

RTRV-EXT-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];

Retrieves the control state of an external control.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:[<CONTTYPE>],<DUR>,[<CONTSTATE>]"
;

SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>::<CONTTYPE>;

Sets the attributes associated with an external control.

SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::<NTFCNCDE>,<ALMTYPE>,<ALMMSG>;

Sets the attributes associated with an external control.


5 Equipment

Table 5 Equipment 

ALW-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];

Allows automatic or manual switching of an equipment unit back to protection.

ALW-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];

Allows automatic or manual switching of an equipment unit back to working.

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::];

Deletes a card from the NE.

ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][PRTYPE=<PRTYPE>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>,]
[CARDMODE=<CARDMODE>,][PEERID=<PEERID>,][REGENNAME=<REGENNAME>,]
[PWL=<PWL>]:[<PST>[,<SST>]];

Edits the attributes for a given equipment slot in the NE.

ENT-EQPT:[<TID>]:<AID>:<CTAG>::<AIDTYPE>:[PROTID=<PROTID>,][PRTYPE=<PRTYPE>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>,]
[CARDMODE=<CARDMODE>,][PEERID=<PEERID>,][REGENNAME=<REGENNAME>,]
[PWL=<PWL>][:];

Enters the card type and attributes for a given equipment slot in the NE.

INH-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::];

Inhibits automatic or manual switching on a system containing duplex equipment.

INH-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];

Inhibits automatic or manual switching of an equipment unit to protection.

INH-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>];

Inhibits automatic or manual switching of an equipment unit back to the working.

REPT ALM EQPT

Reports an alarm condition against an equipment unit or slot.

Output format:

SID DATE TIME
** ATAG REPT ALM EQPT
"<AID>:<NTFCNCDE>,<CONDITION>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>],
[<AIDDET>]"
;

REPT EVT EQPT

Reports the occurrence of a non-alarmed event against an equipment unit or slot.

Output format:

SID DATE TIME
** ATAG REPT EVT EQPT
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>],[<AIDDET>]"
;

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,];

Instructs the NE to retrieve and send the current status of its alarm conditions associated with the equipment units.

Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],,:[<DESC>]"
;

RTRV-ALMTH-EQPT:[<TID>]::<CTAG>::<ALMTHR>[,,::];

Retrieves the alarm thresholds for the power level monitoring of the ONS 15454 SDH.

Output format:

SID DATE TIME
M CTAG COMPLD
",<MOD2B>:<ALMTHR>,,,<DNFIELD>"
;

RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];

Retrieves the condition equipment.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the data parameters and state parameters associated for an equipment unit.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>,]
[PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,]
[CARDNAME=<CARDNAME>,][IOSCFG=<IOSCFG>,][CARDMODE=<CARDMODE>,]
[PEERID=<PEERID>,][REGENNAME=<REGENNAME>,][PWL=<PWL>]:<PST_PSTQ>,
<SSTQ>"
;

SET-ALMTH-EQPT:[<TID>]::<CTAG>::<ALMTHTYPE>,<THLEV>[,,,];

Sets the alarm threshold to manage the power level monitoring on an ONS 15454 SDH.

SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<PROTID>],[<DIRN>];

Switches traffic from the working card to the protect card.

SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>];

Switches traffic to from the protect card to the working card.


6 Facility

Table 6 Facility

RMV-<MOD2>:[<TID>]:<AID>:<CTAG>[::];

Removes a facility from service.

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];

Provisions a facility or service.


7 Fault

Table 7 Fault 

REPT ALM <MOD2ALM>
Reports an alarm condition against a facility or a path.

Output format:

SID DATE TIME
** ATAG REPT ALM <MOD2ALM>
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],,:[<DESC>],[<AIDDET>]"
;

REPT ALM COM
Reports an alarm condition when an AID cannot be given.

Output format:

TID-000 1998-06-20 14:30:00
** ATAG REPT ALM COM
"[<AID>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>]"
;

REPT EVT <MOD2ALM>

Reports the occurrence of a non-alarmed event.

Output format:

SID DATE TIME
A ATAG REPT EVT <MOD2ALM>
"<AID>:<CONDTYPE>,[<CONDEFF>],,,[<LSTM>],,[<MONVAL>],[<THLEV>],
[<TMPER>]:[<DESC>],[<AIDDET>]"
;

REPT EVT COM

Reports a non-alarmed event against a NE when there is no AID associated with it.

Output format:

SID DATE TIME
A ATAG REPT EVT COM
"[<AID>]:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]"
;

RTRV-ALM-ALL:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],
[<CONDITION>],[<SRVEFF>][,,,];

Instructs the NE to retrieve and send the current status of all active alarm conditions.

Output format:

SID DATE TIME
M CTAG COMPLD
"[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,<OCRDAT>,
<OCRTM>,,:[<DESC>],[<AIDDET>]"
;

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];

Retrieves the current standing condition and/or state associated with an entity.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],,,[<DESC>]"
;

RTRV-COND-ALL:[<TID>]:[<AID>]:<CTAG>::[<TYPEREQ>][,,,];

Retrieves the current standing condition for all the entities.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],
[<OCRDAT>],[<OCRTM>],,,[<DESC>]"
;


8 File Transfer

Table 8 File Transfer 

APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>];

Activates or reverts a software load during a software upgrade or downgrading process.

COPY-IOSCFG:[<TID>]:<AID>:<CTAG>::SRC=<SRC>,DEST=<DEST>;

Uploads startup Cisco IOS configuration files from the network to the node and downloads startup Cisco IOS configuration files from the node to the network (ML-Series Ethernet cards).

COPY-RFILE:[<TID>]:[<SRC>]:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>,]
[DEST=<DEST>,][OVWRT=<OVWRT>,][FTTD=<FTTD>];

Downloads a new software package from the location specified by the FTP URL.

REPT EVT FXFR

Reports the FTP software download status of the start, completion, and completed percentage.

Output format:

SID DATE TIME
A ATAG REPT EVT FXFR
"<FILENAME>,<FXFR_STATUS>,[<FXFR_RSLT>],[<PRCNT_XFRD>]"
;

REPT EVT IOSCFG

Reports the status of copying the Cisco IOS config file when the COPY-IOSCFG command is issued.

Output format:

SID DATE TIME
A ATAG REPT EVT IOSCFG
"<AID>:<SRC>,<DEST>,<STATUS>,[<RESULT>]"
;


9 Log

Table 9 Log 

ALW-MSG-DBCHG:[<TID>]::<CTAG>[::,,];
Enables REPT DBCHG.

INH-MSG-DBCHG:[<TID>]::<CTAG>[::,,];

Disables REPT DBCHG.

REPT DBCHG

Reports changes on the NE that result from TL1 provisioning commands or their graphical user interface (GUI) equivalents or an external event such as a board insertion.

Output format:

SID DATE TIME
A ATAG REPT DBCHG
"TIME=<TIME>,DATE=<DATE>,[SOURCE=<SOURCE>,][USERID=<USERID>,]
DBCHGSEQ=<DBCHGSEQ>:<COMMAND>:[<AID>]:::[<PSTPSTQ>,]<SST>"
;

RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>;

Retrieves the alarm log of the NE.


10 Network

Table 10 Network 

RTRV-MAP-NETWORK:[<TID>]::<CTAG>;

Reports all the NE attributes that are reachable from the gateway NE (GNE).

RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>;

Retrieves the IP address and node name of the NEs that have the data communications channel (DCC) connection with this NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<IPADDR>,<NODENAME>"
;


11 Paths

Table 11 Paths 

ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SWPDIP=<SWPDIP>,]
[HOLDOFFTIMER=<HOLDOFFTIMER>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Modifies the attributes associated with a VC or virtual tributary (VT) path.

RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[BLSRPTHTYPE=<BLSRPTHTYPE>][:];

Retrieves the attributes associated with an SDH high/low order path.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,]
[EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,]
[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SNCPPTHSTATE=<SNCPPTHSTATE>,]
[C2=<C2>,][MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-VT:[<TID>]:<AID>:<CTAG>;

Retrieves the attributes associated with a VT path based on the granularity level of NE/slot/specific VTs.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LEVEL=<LEVEL>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,]
[HOLDOFFTIMER=<HOLDOFFTIMER>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,]
[SNCPPTHSTATE=<SNCPPTHSTATE>]:[<PST>[,<SST>]]"
;


12 Performance

Table 12 Performance 

ALW-PMREPT-ALL:[<TID>]::<CTAG>;
Resumes the processing of all performance monitoring (PM) reports that are inhibited.

DLT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,
<INTVL>:RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE>,][STARTUP=<STARTUP>][:];

Deletes a threshold entry in the remote monitoring (RMON) alarm table.

ENT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,
<INTVL>:RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE>,][STARTUP=<STARTUP>][:];

Creates an entry in the RMON alarm table.

INH-PMREPT-ALL:[<TID>]::<CTAG>;

Inhibits all scheduled PM reporting.

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LSTM>],
[<DIRN>],[<TMPER>][,,];

Initializes the PM registers.

REPT PM <MOD2>

Reports performance monitoring statistics as a result of schedule created by SCHED-PMREPT.

Output format:

SID DATE TIME
A ATAG REPT PM <MOD2>
"<AID>:<MONTYPE>,<MONVAL>,<VLDTY>,<LSTM>,<DIRN>,<TMPER>,
<MONDAT>,<MONTM>"
;

RTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],
[<LSTM>],[<DIRECTION>],[<TMPER>],[<DATE>],[<TIME>];

Retrieves the values of PM parameters for a specified card type.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LSTM>],[<DIRECTION>],
[<TMPER>],[<MONDAT>],[<MONTM>]"
;

RTRV-PMMODE-<VC_PATH>:[<TID>]:<SRC>:<CTAG>::<LSTM>;

Instructs an SDH NE to send the type of PM mode that has been previously set in the NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"<CROSSCONNECTID>:[<LSTM>],<MODETYPE>"
;

RTRV-PMSCHED-<MOD2>:[<TID>]:<AID>:<CTAG>;

Retrieves a PM reporting schedule that was set for the NE by SCHED-PMREPT command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],,[<MONLEV>],
<LSTM>,,[<TMPER>],[<TMOFST>],[<INHMODE>]"
;

RTRV-PMSCHED-ALL:[<TID>]::<CTAG>;

Retrieves all the PM reporting schedules that were set for the NE by SCHED-PMREPT command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],,[<MONLEV>],
<LSTM>,,[<TMPER>],<TMOFST>,[<INHMODE>]"
;

RTRV-RMONTH-<MOD2_RMON>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],,,,
[<INTVL>]:[RISE=<RISE>,][FALL=<FALL>,][SAMPLE=<SAMPLE>,][STARTUP=<STARTUP>][:];

Retrieves the thresholds defined in the RMON alarm table.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AIDUNIONID>,<AIDTYPE>:<MONTYPE>,,,,<INTVL>:INDEX=<INDEX>,RISE=<RISE>,
FALL=<FALL>,SAMPLE=<SAMPLE>,STARTUP=<STARTUP>"
;

RTRV-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<LSTM>],<TMPER>[::];

Retrieves the current threshold level of one or more monitored parameters.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,[<LSTM>],,<THLEV>,[<TMPER>]"
;

RTRV-TH-ALL:[<TID>]::<CTAG>::[<MONTYPE>],[<LOCATION>],[<TMPER>][::];

Retrieves the current threshold level of all monitored parameters on the NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>:<MONTYPE>,<LOCATION>,,<THLEV>,<TMPER>"
;

SCHED-PMREPT-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<REPTINVL>],[<REPTSTATM>],
[<NUMREPT>],,[<MONLEV>],[<LSTM>],,[<TMPER>],[<TMOFST>];

Allows scheduling/rescheduling the NE to report the PM data for a line facility or for a VC path periodically, using the automatic REPT PM message.

SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LSTM>],,[<TMPER>];

Sets the thresholds for PMs and the alarm thresholds for a MXP_2.5G_10G/TXP_MR_10G card facility; if used to set alarm thresholds, the time period (tmper) is not applicable.


13 Ports

Table 13 Ports 

DLT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Deletes the specified port.

ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>,][MACADDR=<MACADDR>,]
[CMDMDE=<CMDMDE>]:[<PST>],[<SST>];

Edits Gigabit Ethernet facility attributes.

ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>,]
[DISTEXTN=<DISTEXTN>,][AUTODETECTION=<AUTODETECTION>,][LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits the attributes related with the Fibre Channel facility.

ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>,]
[DISTEXTN=<DISTEXTN>,][AUTODETECTION=<AUTODETECTION>,]
[LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][NAME=<NAME>,]
[CMDMDE=<CMDMDE>]:<PST>,<SST>;

Edits the attributes related to the FICON payload facility.

ED-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>,][AREA=<AREA>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][MUX=<MUX>,][SOAK=<SOAK>,][OSPF=<OSPF>,]
[LDCC=<LDCC>,][NAME=<NAME>,][CMDMDE=<CMDMDE>,][EXPTRC=<EXPTRC>,]
[TRC=<TRC>,][TRCMODE=<TRCMODE>,][TRCFROMAT=<TRCFROMAT>,]
[ADMSSM=<ADMSSM>,][SENDDUSFF=<SENDDUSFF>,]
[AISONLPBK=<AISONLPBK>]:[<PST>],[<SST>];

Modifies the attributes (that is, service parameters) and state of an STM facility.

ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>];

Modifies the automatic laser shutdown (ALS) attributes of an STM facility and in general for all the facilities that support the ALS feature.

ED-DS3I:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,]
[INHFELPBK=<INHFELPBK>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>],
[<SST>];

Modifies the attributes of a DS3i-N-12 facility.

ED-E1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][TACC=<TACC>,]
[TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,]
[NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Supports provisioning of an E1 facility.

ED-E3:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>],
[<SST>];

Supports provisioning of an E3 facility.

ED-E4:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,]
[NAME=<NAME>,][CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Modifies the attributes and the state of the E4 port facility.

ED-FAC:[<TID>]:<SRC>:<CTAG>:::[PAYLOAD=<PAYLOAD>,]
[CMDMDE=<CMDMDE>]:[<PST>],[<SST>];

Provisions the payload (or signal) type of the facility.

ED-FSTE:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>,][EXPDUPLEX=<EXPDUPLEX>,]
[EXPSPEED=<EXPSPEED>,][VLANCOS=<VLANCOS>,][IPTOS=<IPTOS>,][NAME=<NAME>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edits the front end port information of the Fast Ethernet (10/100 Mbps) card.

ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>,][FLOW=<FLOW>,]
[LOWMRK=<LOWMRK>,][HIWMRK=<HIWMRK>,][AUTONEG=<AUTONEG>,]
[NAME=<NAME>,][CMDMDE=<CMDMDE>,][SOAK=<SOAK>]:[<PST>[,<SST>]];

Modifies the attributes related to a G1000 port.

ED-GFP:[<TID>]:<AID>:<CTAG>:::[FCS=<FCS>,][AUTOTHGFPBUF=<AUTOTHGFPBUF>,]
[GFPBUF=<GFPBUF>,][FILTER=<FILTER>];

Edit generic framing procedure (GFP); used for GFP management.

ED-POS:[<TID>]:<AID>:<CTAG>:::[ENCAP=<ENCAP>,][NAME=<NAME>,]
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Edit packet-over-SDH (POS); used for POS management.

ED-STM1E:[<TID>]:<SRC>:<CTAG>:::[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,]
[SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>,]
[CMDMDE=<CMDMDE>]:[<PST>=[,<SST>]];

Modifies the attributes and the state of the STM1E port facility.

ENT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Creates the specified port.

OPR-ALS:[<TID>]:<AID>:<CTAG>[::::];

Restarts the laser of an STM facility.

RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes related with the Fibre Channel (FC) port.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>,
[LINKRCVRY=<LINKRCVRY>,][DISTEXTN=<DISTEXTN>,]
[LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][ENCAP=<ENCAP>,][NAME=<NAME>,]
[SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SST>]"
;

RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>;

Returns Fibre Channel specific settings for ports that have been configured to carry FICON traffic using the ENT-FICON command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LINKRATE=<LINKRATE>,][LINKSTATE=<LINKSTATE>,]
[LINKRCVRY=<LINKRCVRY>,][DISTEXTN=<DISTEXTN>,]
[LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][ENCAP=<ENCAP>,]
[NAME=<NAME>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,<SST>"
;

RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes (that is, service parameters) and state of an STM facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>,][AREA=<AREA>,][TMGREF=<TMGREF>,]
[SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,]
[SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][WVLEN=<WVLEN>,]
[RINGID=<RINGID>,][MSSPRTYPE=<MSSPRTYPE>,][MUX=<MUX>,][UNIC=<UNIC>,]
[CCID=<CCID>,][NBRIX=<NBRIX>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,]
[SSMRCV=<SSMRCV>,][OSPF=<OSPF>,][LDCC=<LDCC>,][NAME=<NAME>,]
[LBCL=<LBCL>,][OPT=<OPT>,][OPR=<OPR>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,]
[TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>,][ADMSSM=<ADMSSM>,]
[SENDDUSFF=<SENDDUSFF>,][AISONLPBK=<AISONLPBK>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::];

Used to retrieve the 10-Gbps-specific parameters for a port configured to support the gigabyte Ethernet payload using the ENT-10GIGE command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[NAME=<NAME>,][MACADDR=<MACADDR>,][LBCL=<LBCL>,]
[OPT=<OPT>,][OPR=<OPR>]:<PST_PSTQ>,[<SST>]"
;

RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the ALS attributes of an STM facility and in general for all facilities that support the ALS feature.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,]
[ALSRCPW=<ALSRCPW>,][LSRSTAT=<LSRSTAT>]"
;

RTRV-DS3I:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the properties of a DS3i-N-12 facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::FMT=<FMT>,LINECDE=<LINECDE>,LBO=<LBO>,[INHFELPBK=<INHFELPBK>,]
[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,][SDBER=<SDBER>,]
[SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-E1:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes and state information of an E1 port facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::LINECDE=<LINECDE>,FMT=<FMT>,[TACC=<TACC>,]
[TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,]
[NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-E3:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes and state information of an E3 port facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,]
[SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-E4:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes and state information of an E4 port facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[PAYLOAD=<PAYLOAD>,][SFBER=<SFBER>,][SDBER=<SDBER>,]
[SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-ESCON:[<TID>]:<AID>:<CTAG>;

Retrieves Fibre Channel specific settings for ports that have been configured to carry ESCON traffic using the ENT-ESCON command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ENCAP=<ENCAP>]"
;

RTRV-FAC:[<TID>]:<SRC>:<CTAG>[::::];

Retrieves the payload type of the facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<SRC>::PAYLOAD=<PAYLOAD>:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-FSTE:[<TID>]:<AID>:<CTAG>;

Retrieves the front end port information of a Fast Ethernet (10/100 Mbps) card.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,]
[MTU=<MTU>,][FLOWCTRL=<FLOWCTRL>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>,]
[FLOW=<FLOW>,][EXPDUPLEX=<EXPDUPLEX>,][EXPSPEED=<EXPSPEED>,]
[VLANCOS=<VLANCOS>,][IPTOS=<IPTOS>,][NAME=<NAME>,][SOAK=<SOAK>,]
[SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-G1000:[<TID>]:<AID>:<CTAG>;

Retrieves the G1000 facilities configuration.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[MFS=<MFS>,][FLOW=<FLOW>,][LAN=<LAN>,][OPTICS=<OPTICS>,]
[TRANS=<TRANS>,][TPORT=<TPORT>,][LOWMRK=<LOWMRK>,]
[HIWMRK=<HIWMRK>,][AUTONEG=<AUTONEG>,][ENCAP=<ENCAP>,]
[NAME=<NAME>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]"
;

RTRV-GFP:[<TID>]:<SRC>:<CTAG>;

Retrieves GFP; used for GFP management.

Output format:

SID DATE TIME

M CTAG COMPLD
"<AID>::[FCS=<FCS>,][AUTOTHGFPBUF=<AUTOTHGFPBUF>,][GFPBUF=<GFPBUF>,]
[FILTER=<FILTER>]"
;

RTRV-GIGE:[<TID>]:<AID>:<CTAG>;

Retrieves front end port information of a 1 Gigabit Ethernet card.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,]
[MTU=<MTU>,][ENCAP=<ENCAP>,][FLOWCTRL=<FLOWCTRL>,]
[OPTICS=<OPTICS>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>,][NAME=<NAME>]"
;

RTRV-POS:[<TID>]:<AID>:<CTAG>;

Retrieves the back-end port information for the Ethernet card, when the back-end port is working in POS mode.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,]
[MTU=<MTU>,][ENCAP=<ENCAP>,][NAME=<NAME>,][SOAK=<SOAK>,]
[SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SST>]"
;

RTRV-STM1E:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the attributes and state information of an STM1E facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[PAYLOAD=<PAYLOAD>,][SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,]
[SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,
[<SSTQ>]"
;


14 Protection

Table 14 Protection 

DLT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::];

Deletes a facility protection group (STM4, STM64, STM1, STM16).

ED-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,]
[RVTM=<RVTM>,][PSDIRN=<PSDIRN>,][VRGRDTM=<VRGRDTM>,]
[DTGRDTM=<DTGRDTM>,][RCGRDTM=<RCGRDTM>][:];

Edits a facility protection group (STM4, STM64, STM1, STM16).

ENT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>:::[PROTID=<PROTID>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>,][OPOTYPE=<OPOTYPE>,]
[VRGRDTM=<VRGRDTM>,][DTGRDTM=<DTGRDTM>,][RCGRDTM=<RCGRDTM>][:];

Enters a facility protection group (STM4, STM64, STM1, STM16).

OPR-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>::<SC>,[<SWITCHTYPE>][:<DIRN>];

Operates a protection switch (STM4, STM64, STM1, STM16).

OPR-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>::<SC>[:];

Instructs an SDH NE to initiate a subnetwork connection protection (SNCP) switch request.

REPT SW

Reports the autonomous switching of a unit in a duplex equipment unit pair to standby and its mate unit to the active state.

Output format:

SID DATE TIME
A ATAG REPT SW
"<ACTID>,<STDBYID>"
;

RLS-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::<DIRECTION>];

Instructs an SDH NE to release (clear) an SDH line protection switch request.

RLS-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>[::];

Instructs an SDH NE to release (clear) an SDH path protection switch request that was established with the OPR-PROTNSW-(MOD_PATH) command.

RTRV-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the optical facility protection information.

Output format:

SID DATE TIME
M CTAG COMPLD
"<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,]
[PSDIRN=<PSDIRN>,][VRGRDTM=<VRGRDTM>,][DTGRDTM=<DTGRDTM>,]
[RCGRDTM=<RCGRDTM>,][OPOTYPE=<OPOTYPE>]"
;

RTRV-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the switching state of an SDH line.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<SC>,[<SWITCHTYPE>]"
;


15 Provisionable Patchcords

Table 15 Provisionable Patchcords 

DLT-LNKTERM:[<TID>]:<AID>:<CTAG>;

Deletes a provisionable patchcord termination present on a node.

ED-LNKTERM:[<TID>]:<AID>:<CTAG>:::[REMOTENODE=<REMOTENODE>,]
[REMOTELNKTERMID=<REMOTELNKTERMID>];

Edits the attributes of an already created provisionable patchcord termination.

ENT-LNKTERM:[<TID>]:<AID>:<CTAG>:::PORT=<PORT>,
[REMOTENODE=<REMOTENODE>,]REMOTELNKTERMID=<REMOTELNKTERMID>;

Creates a provisionable patchcord (PP) termination (virtual link) on a physical interface.

RTRV-LNKTERM:[<TID>]:<AID>:<CTAG>;

Retrieves information about one or more PP terminations.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::PORT=<PORT>,[REMOTENODE=<REMOTENODE>,]
[REMOTELNKTERMID=<REMOTELNKTERMID>]"
;


16 Security

Table 16 Security 

ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Sets up a session with the NE.

ALW-MSG-SECU:[<TID>]::<CTAG>;

Enables the REPT EVT SECU and REPT ALM SECU autonomous messages.

ALW-USER-SECU:[<TID>]::<CTAG>::<UID>;

Enables a userid that has been disabled using the INH-USE-SECU command.

CANC

Reports the occurrence of a session timeout event.

Output format:

SID DATE TIME
A ATAG CANC
"<UID>"
;

CANC-USER:[<TID>]:<USERID>:<CTAG>;

Logs a user out of an active session with the NE.

CANC-USER-SECU:[<TID>]:<UID>:<CTAG>;

Forces a user off the NE.

CLR-COND-SECU:[<TID>]::<CTAG>[::<SECUALMTYPE>];

Clears the specified standing condition.

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>;

Removes a user; can only be performed by a Superuser.

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;

Allows provisioning of the command security level of a particular command.

ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>;

Allows a user to change his/her password.

ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:];

Changes a user's ID, privilege, or password; can only be performed by a Superuser.

ENT-USER-SECU:[<TID>]:<UID>:<CTAG>::<PID>,,<UAP>[:];

Adds a user account; can only be performed by a Superuser.

INH-MSG-SECU:[<TID>]::<CTAG>;

Disables the REPT EVT SECU and REPT ALM SECU autonomous messages.

INH-USER-SECU:[<TID>]::<CTAG>::<UID>;

Disables (without deleting) a user account so the user is denied access to the NE.

REPT ALM SECU

Reports the occurrence of an alarmed security event against the NE.

Output format:

SID DATE TIME
** ATAG REPT ALM SECU
"<AID>:<NOTIFCODE>,<SECUALMTYPE>"
;

REPT EVT SECU

Reports the occurrence of a non-alarmed user or system security event against the NE.

Output format:

SID DATE TIME
A ATAG REPT EVT SECU
"<AID>:<DNFIELD>,[<CONDEFF>],,,,,,,:<SECURITY>:<DNFIELD1>"
;

REPT EVT SESSION

Reports a non-alarmed event related to establishing a session with the NE.

Output format:

SID DATE TIME
A ATAG REPT EVT SESSION
"<AID>:<EXP>,<PCN>"
"<WARN>"
;

RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;

Retrieves the current command security level of the command specified in the AID field.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<CAP>"
;

RTRV-DFLT-SECU:[<TID>]:<AID>:<CTAG>;

Retrieves default security information; used by an administrator to retrieve the system-wide default values associated with several security parameters.

Output format:

SID DATE TIME
M CTAG COMPLD
"<NE>:PAGE=<PAGE>,PCND=<PCND>,MXINV=<MXINV>,DURAL=<DURAL>,
TMOUT=<TMOUT>,UOUT=<UOUT>,PFRCD=<PFRCD>,POLD=<POLD>,PINT=<PINT>,
LOGIN=<LOGIN>,PRIVLVL=<UAP>"
;

RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>;

Retrieve user security; retrieves the security information of a specified user or list of users.

Output format:

SID DATE TIME
M CTAG COMPLD
"<UID>:,<PRIVILEGE>:LOGGEDIN=<LOGGEDIN>,[NUMSESSIONS=<NUMSESS>,]
[LOCKEDOUT=<LOCKEDOUT>,][DISABLED=<DISABLED>]"
;

SET-ATTR-SECUDFLT:[<TID>]::<CTAG>::[PAGE=<PAGE>,][PCND=<PCND>,]
[MXINV=<MXINV>,][DURAL=<DURAL>,][TMOUT=<TMOUT>,][UOUT=<UOUT>,]
[PFRCD=<PFRCD>,][POLD=<POLD>,]
[PINT=<PINT>,][LOGIN=<LOGIN>,][PRIVLVL=<UAP>];

Sets attribute security defaults; used by an administrator to set the system-wide defaults associated with several security parameters.


17 Synchronization

Table 17 Synchronization 

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,]
[SYNCMSG=<SYNCMSG>,][AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,]
[IMPEDANCE=<IMPEDANCE>,][BITSFAC=<BITSFAC>,][ADMSSM=<ADMSSM>][:<PST>];

Edits the building integrated timing supply (BITS) reference attributes.

ED-NE-SYNCN:[<TID>]::<CTAG>:::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,]
[QRES=<QRES>,][RVRTV=<RVRTV>,][RVTM=<RVTM>];

Edits the synchronization attributes of the NE.

ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>,][SEC=<SEC>,][THIRD=<THIRD>][:];

Modifies the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock.

OPR-SYNCNSW:[<TID>]:[<AID>]:<CTAG>::<SWITCHTO>,[<SC>];

Forces the NE to switch to the reference specified by the synchronization reference number if the reference supplied is valid and of the same quality; otherwise the command will fail.

REPT ALM BITS

Reports an alarm condition on a BITS facility.

Output format:

SID DATE TIME
** ATAG REPT ALM BITS
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>]"
;

REPT ALM SYNCN

Reports an alarm condition against a synchronization reference.

Output format:

SID DATE TIME
** ATAG REPT ALM SYNCN
"<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>],
[<EQPTTYPE>]"
;

REPT EVT BITS

Reports a non-alarmed event against a BITS facility.

Output format:

SID DATE TIME
A ATAG REPT EVT BITS
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]"
;

REPT EVT SYNCN

Reports the occurrence of a non-alarmed event against a synchronization entity.

Output format:

SID DATE TIME
A ATAG REPT EVT SYNCN
"<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>],[<AIDDET>]"
;

RLS-SYNCNSW:[<TID>]:[<AID>]:<CTAG>;

Releases the previous synchronization reference provided by the OPR-SYNCNSW command.

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,];

Instructs the NE to retrieve and send the current status of its alarm conditions associated with the BITS facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],,:[<DESC>]"
;

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],
[<SRVEFF>][,,,];

Instructs the NE to retrieve and send the current status of its alarm conditions associated with a synchronization facility.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],,:[<DESC>]"
;

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the BITS configuration command.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,]
[SYNCMSG=<SYNCMSG>,][AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,]
[IMPEDANCE=<IMPEDANCE>,][BITSFAC=<BITSFAC>,][ADMSSM=<ADMSSM>]:[<PST>]"
;

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];

Retrieves the standing conditions on BITS.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],
[<OCRDAT>],[<OCRTM>],,,[<DESC>]"
;

RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,];

Retrieves the synchronization condition.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],
[<OCRDAT>],[<OCRTM>],,,[<DESC>]"
;

RTRV-NE-SYNCN:[<TID>]::<CTAG>[::::];

Retrieves the synchronization attributes of the NE.

Output format:

SID DATE TIME
M CTAG COMPLD
"::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,][QRES=<QRES>,]
[RVRTV=<RVRTV>,][RVTM=<RVTM>]"
;

RTRV-SYNCN:[<TID>]:<AID>:<CTAG>[::::];

Retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>:<REF>,<REFVAL>,[<QREF>],[<STATUS>],[<PROTECTSTATUS>]"
;


18 System

Table 18 System 

ALW-MSG-ALL:[<TID>]:[<AID>]:<CTAG>[::,,];

Allows REPT ALM and REPT EVT autonomous messages to be transmitted.

DLT-ROUTE:[<TID>]::<CTAG>::<DESTIP>,<IPMASK>;

Deletes the static routes.

DLT-TRAPTABLE:[<TID>]:<AID>:<CTAG>;

Deletes Simple Network Management Protocol (SNMP) trap destination entry.

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];

Edits the date and time.

ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>,][IPADDR=<IPADDR>,]
[IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,][IIOPPORT=<IIOPPORT>,][NTP=<NTP>,]
[ETHIPADDR=<ETHIPADDR>,][ETHIPMASK=<ETHIPMASK>];

Edits the node attributes of an NE.

ED-NE-PATH:[<TID>]::<CTAG>[:::PDIP=<PDIP>];

Edits path related parameters for the NE-wide basis.

ED-TRAPTABLE:[<TID>]:<AID>:<CTAG>::<SKIPPED>:COMMUNITY=<COMMUNITY>,
[TRAPPORT=<TRAPPORT>,][TRAPVER=<TRAPVER>];

Modifies a trap destination entry identified by a specific trap destination address.

ENT-ROUTE:[<TID>]::<CTAG>::<DESTIP>,<IPMASK>,<NXTHOP>,<COST>;

Creates the static route.

ENT-TRAPTABLE:[<TID>]:<AID>:<CTAG>::COMMUNITY=<COMMUNITY>,
[TRAPPORT=<TRAPPORT>,][TRAPVER=<TRAPVER>];

Provisions SNMP trap destination and its associated community, user datagram protocol (UDP) port, and SNMP version.

INH-MSG-ALL:[<TID>]:[<AID>]:<CTAG>[::,,];

Instructs the NE to enter a mode in which all REPT ALM and REPT EVT autonomous messages are prevented from being transmitted.

INIT-SYS:[<TID>]:<AID>:<CTAG>::<PH>,[<CMDMODE>];

Instructs the NE to initialize the specified card and its associated subsystem(s).

RTRV-HDR:[<TID>]::<CTAG>;

Instructs the NE to return the header of a TL1 response message.

RTRV-INV:[<TID>]:<AID>:<CTAG>[::::];

Retrieves a listing of the equipment inventory.

Output format:

SID DATE TIME
M CTAG COMPLD
"<AID>,<AIDTYPE>::[PLUGTYPE=<PLUGTYPE>,][PN=<PN>,][HWREV=<HWREV>,]
[FWREV=<FWREV>,][SN=<SN>,][CLEI=<CLEI>,][TWL1=<TWL>,][TWL2=<TWL1>,]
[TWL3=<TWL2>,][TWL4=<TWL3>,][PLUGINVENDORID=<PLUGINVENDORID>,]
[PLUGINPN=<PLUGINPN>,][PLUGINHWREV=<PLUGINHWREV>,]
[PLUGINFWREV=<PLUGINFWREV>,][PLUGINSN=<PLUGINSN>,]
[ILOSSREF=<ILOSSREF>,][PID=<PID>,][VID=<VID>,][FPGA=<FPGA>]"
;

RTRV-NE-GEN:[<TID>]::<CTAG>;

Retrieves the general NE attributes.

Output format:

SID DATE TIME
M CTAG COMPLD
"[IPADDR=<IPADDR>,][IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,]
[IIOPPORT=<IIOPPORT>,][NTP=<NTP>,][ETHIPADDR=<ETHIPADDR>,]
[ETHIPMASK=<ETHIPMASK>,][NAME=<NAME>,][SWVER=<SWVER>,]
[LOAD=<LOAD>,][PROTSWVER=<PROTSWVER>,][PROTLOAD=<PROTLOAD>,]
[DEFDESC=<DEFDESC>,][PLATFORM=<PLATFORM>,][SECUMODE=<SECUMODE>]"
;

RTRV-NE-PATH:[<TID>]::<CTAG>[::::];

Retrieves path level attributes on an NE-wide basis.

Output format:

SID DATE TIME
M CTAG COMPLD
"[PDIP=<PDIP>]"
;

RTRV-NETYPE:[<TID>]::<CTAG>;

Retrieves the NE's equipment-related information.

Output format:

SID DATE TIME
M CTAG COMPLD
"<CISCO>,<PRODUCTTYPE>,<ADMMSPPMSTP>,<X>"
;

RTRV-ROUTE:[<TID>]::<CTAG>::[<DESTIP>],[<IPMASK>],[<NXTHOP>],[<COST>];

Retrieves static routes.

Output format:

SID DATE TIME
M CTAG COMPLD
",:<DESTIP>,<IPMASK>,<NXTHOP>,<COST>"
;

RTRV-TOD:[<TID>]::<CTAG>;

Queries the NE and displays the system date and time at the instant when the command was executed.

Output format:

SID DATE TIME
M CTAG COMPLD
"<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,<TMTYPE>"
;

RTRV-TRAPTABLE:[<TID>]:[<AID>]:<CTAG>;

Retrieves a trap destination entry based on the destination address.

Output format:

SID DATE TIME
M CTAG COMPLD
"<DEST>,<TRAPPORT>,<COMMUNITY>,<SNMPVERSION>"
;

SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,
[<DIFFERENCE>][:DST=<DST>];

Sets the system date and time for the NE.


19 Troubleshooting and Test Access

Table 19 Troubleshooting and Test Access 

CHG-ACCMD-<MOD_TACC>:[<TID>]:<TAP>:<CTAG>::<MD>;

Changes the test access mode for the circuit being tested.

CONN-TACC-<MOD_TACC>:[<TID>]:<SRC>:<CTAG>::<TAP>:MD=<MD>;

Connects the VC or VT defined by AID to the VC specified by the test access point (TAP) number.
Output format:

SID DATE TIME
M CTAG COMPLD
"<TAP>"
;

DISC-TACC:[<TID>]:<TAP>:<CTAG>;

Disconnects the TAP and puts the connection back to its original state.

OPR-LPBK-<MOD2>:[<TID>]:<AID>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>];

Operates a signal loopback on an input/output (I/O) card or on a cross-connect.

RLS-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>];

Releases a signal loopback on an I/O card or on a cross-connect.

RTRV-PTHTRC-<PATH>:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>][:<LSTM>];

Instructs an SDH NE to retrieve the contents of the SDH path trace message.

Output format:

SID DATE TIME
M CTAG COMPLD
"<TRACMSG>"
;

RTRV-TACC:[<TID>]:<TAP>:<CTAG>;

Retrieves details associated with a TAP.

Output format:

SID DATE TIME
M CTAG COMPLD
"<TAP>:<TACC_AIDA>,<TACC_AIDB>,[<MD>],[<CROSSCONNECTID1>],
[<CROSSCONNECTID2>]"
;


20 VCAT

Table 20 VCAT 

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:];

Deletes a virtual concatenated group (VCG) object.

ED-VCG:[<TID>]:<SRC>:<CTAG>:::[TXCOUNT=<TXCOUNT>,][NAME=<NAME>];

Edits the attributes of a VCG.

ENT-VCG:[<TID>]:<SRC>:<CTAG>:::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,[CCT=<CCT>,]
[LCAS=<LCAS>,][BUFFERS=<BUFFERS>,][NAME=<NAME>];

Creates a VCG object.

RTRV-VCG:[<TID>]:<SRC>:<CTAG>[::::];

Retrieves all the attributes provisioned for a VCG.

Output format:

SID DATE TIME
M CTAG COMPLD
"<SRC>::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,CCT=<CCT>,[LCAS=<LCAS>,]
[BUFFERS=<BUFFERS>,][NAME=<NAME>]:<PST>"
;