Cisco ONS 15454 SDH TL1 Command Guide, Release 5.0
Chapter 4, TL1 Command Components
Downloads: This chapterpdf (PDF - 485.0KB) The complete bookPDF (PDF - 9.12MB) | Feedback

TL1 Command Components

Table Of Contents

TL1 Command Components

4.1  TL1 Default Values

4.1.1  MS-SPRing

4.1.2  Cross Connections

4.1.3  Environment Alarms and Controls

4.1.4  Equipment

4.1.5  Performance

4.1.6  Ports

4.1.7  SDH Line Protection

4.1.8  VC Paths

4.1.9  Synchronization

4.1.10  Testing

4.2  Modifier Support by Platform

4.3  Starting Positions for an STS-Mc SPE

4.4  Conditions

4.5  Access Identifiers

4.5.1  ALL

4.5.2  AidUnionId

4.5.3  AidUnionId1

4.5.4  BAND

4.5.5  BITS

4.5.6  CHANNEL

4.5.7  COM

4.5.8  CrossConnectId

4.5.9  CrossConnectId1

4.5.10  ENV

4.5.11  EQPT

4.5.12  FACILITY

4.5.13  IPADDR

4.5.14  LINE

4.5.15  LNKTERM

4.5.16  MSSPR

4.5.17  OPM

4.5.18  OSC

4.5.19  PRSLOT

4.5.20  RFILE

4.5.21  SYN

4.5.22  SYN_SRC

4.5.23  SYNC_REF

4.5.24  SYNCSW

4.5.25  UDC

4.5.26  VC

4.5.27  WDMANS

4.5.28  WLEN

4.6  Parameter Descriptions

4.6.1  ATAG Description

4.6.2  CTAG Description

4.6.3  TID Description

4.6.4  Parameter Notes


TL1 Command Components


This chapter describes the components of TL1 commands and autonomous messages for the Cisco ONS 15454 SDH, Release 5.0, including:

TL1 default values

Modifier support by platform

Starting positions for an STS-Mc SPE

Access identifiers (AIDs)

Parameter Notes

4.1  TL1 Default Values

4.1.1  MS-SPRing

Table 4-1 MS-SPRing Default Values

MS-SPRing
Default

RVRTV

Y

RVTM

5.0 minutes

SRVRTV

Y

SRVTM

5.0 minutes


4.1.2  Cross Connections

Table 4-2 Cross Connections Default Values

Cross Connections
Default

CCT

2WAY for both VCp and VC11 cross-connections


4.1.3  Environment Alarms and Controls

Table 4-3 Environment Alarms and Controls Default Values 

Environment Alarms and Controls
Default

OPR-EXT-CONT

CONTTYPE is set as one provisioned in the respective AID, there is not default for it. It is only used as a filter if entered. DUR is always taken as CONT.

RTRV-ATTR-CONT

There is no default for CONTTYPE. It is only used as a filter if entered.

RTRV-ATTR-ENV

There is no default for both NTFCNCDE and ALMTYPE, which are only used as filters if entered.

RTRV-EXT-CONT

CONTTYPE defaults to the conttype associated with the AID.

SET-ATTR-ENV

NTFCNCDE defaults to NR. ALMTYPE defaults to NULL. ALMMSG defaults to \"Env Alarm Input 1\".


4.1.4  Equipment

Table 4-4 Equipment Default Values 

Equipment
Default

ALW-SWTOPROTN-EQPT, INH-SWTOPROTN-EQPT and ALW-SWTOWKG-EQPT, ING-SWTOWKG-EQPT

DIRN defaults to BTH

ENT-EQPT

PROTID, PRTYPE, RVRTV and RVTM defaults to NULL

SW-DX-EQPT

MODE defaults to NORM

SW-TOPROTN-EQPT and
SW-TOWKG-EQPT

MODE defaults to NORM
DIRN defaults to BTH


4.1.5  Performance

Table 4-5 Performance Default Values 

Performance
Default

INIT-REG-<MOD2>

LOCN defaults to NEND (near end)

RTRV-PM-<MOD2>

LOCN defaults to NEND
TMPER defaults to 15 minutes

RTRV-TH-<MOD2>

MONTYPE defaults to CVL for STM
MONTYPE defaults to ESP for VCp
MONTYPE defaults to UASV for VC11
LOCN defaults to NEND
TMPER defaults to 15 minutes

SET-PMMODE-<STS_PATH>

PMSTATE defaults to ON

SET-TH-<MOD2>

LOCN defaults to NEND
TMPER defaults to 15 minutes


4.1.6  Ports

Table 4-6 Ports Default Values 

Ports
Default

STM Line

DCC defaults to N
TMGREF defaults to N
SYNCMSG defaults to Y
SENDDUS defaults to N
PJMON defaults to 0
SFBER defaults to 1E-4
SDBER defaults to 1E-7
MODE defaults to SDH
PST defaults to OOS


4.1.7  SDH Line Protection

Table 4-7 SDH Line Protection Default Values 

SDH Line Protection
Default

EX-SW-<STM>

ST (switch type) is optional and for MS-SPRing protection switch only
ST defaults to MS-SPRing switch type

STM Line Protection

PROTID defaults to the protecting port of the protection group (SLOT-#(OCN)PORT-#). It is a string that can have a maximum length of 32 characters
RVRTV defaults to N (non-revertive mode)
RVTM defaults to 5.0 minutes
PSDIRN defaults to UNI

OPR-PROTNSW-<STM>

ST (switch type) is optional and for MS-SPRing protection switch only
ST defaults to MS-SPRing switch type


4.1.8  VC Paths

Table 4-8 VC Paths Default Values 

VC Paths
Default

VC Path

SFBER, SDBER, RVRTV, and RVTM apply to SNCP VC paths only
SFBER defaults to 1E-4
SDBER defaults to 1E-6
RVRTV defaults to N
RVTM defaults to empty because RVRTV is N when SNCP VCp is created

J1 is implemented on DS3i-N-12, STM1, STM16 AND STM64 cards
TRCMODE defaults to the OFF mode

EXPTRC defaults to a copy of the provisioned string or NULL when TRCMODE is OFF mode
EXPTRC defaults to the user entered string when the TRCMODE is MANUAL mode
EXPTRC defaults to a copy of the acquired received string or NULL if the string has not been acquired when the TRCMODE is AUTO mode

INCTRC defaults to the incoming string (NULL) when the TRCMODE is under OFF mode
INCTRC defaults to a copy of the received string or NULL if the string has not been received when the TRCMODE is under MANUAL or AUTO mode


4.1.9  Synchronization

Table 4-9 Synchronization Default Values 

Synchronization
Default

BITS

LINECDE defaults to B8ZS
FMT defaults to ESF
SYNCMSG defaults to Y
PST defaults to OOS

NE-SYNCN

TMMDE defaults to EXTERNAL
SSMGEN defaults to GEN1
QRES defaults to SAME-AS-DUS
RVRTV defaults to Y
RVTM defaults to 5.0 minutes

SYNCN

PRI/SEC QREF defaults to PRS
PRI STATUS defaults to ACT
SEC STATUS defaults to STBY
THIRD QREF defaults to ST3
STATUS defaults to STBY


4.1.10  Testing

Table 4-10 Testing Default Values 

Testing
Default

OPR-LPBK

LPBKTYPE defaults to FACILITY

RLS-LPBK

LPBKTYPE defaults to current existing loopback type


4.2  Modifier Support by Platform

Table 4-11 details the TL1 modifiers supported on the ONS 15454 SDH for commands that have carets (< >) in part of their input format; for example, RTRV-<STM_TYPE>. A "Yes" in the ONS 15454 SDH column indicates that a particular modifier is supported in that platform. A "No" in the platform column indicates that a particular modifier is not supported in that platform. A "—" indicates that a particular modifier is not applicable to that platform.

Table 4-11 Modifier Support 

Modifier
ONS 15454 SDH

E1

Yes

E3

Yes

VC11

Yes

VC3

Yes

VC4

Yes

VC42C

Yes

VC43C

Yes

VC44C

Yes

VC48C

Yes

VC416C

Yes

VC464C

Yes

STM1

Yes

STM4

Yes

STM16

Yes

STM64

Yes

G1000

Yes

GIGE

Yes

FSTE

Yes

POS

Yes

E100

Yes

E1000

Yes

CLNT

Yes

OCH

Yes

OMS

Yes

OTS

Yes


4.3  Starting Positions for an STS-Mc SPE

Table 4-12, Table 4-13, and Table 4-14 list possible starting positions for Cisco ONS 15454 SDH STS-Mc SPE. In each of the tables a "Y" indicates "Yes, this position is supported" and an "N" indicates, "No, this position is not supported".

Table 4-12 Starting Positions for an STS-Mc SPE in an STM4 Signal 

VC Number
VC4 SPE
VC4-2C SPE
VC4-3C SPE
VC4-4C SPE

1

Y

Y

Y

Y

4

Y

Y

Y

N

7

Y

Y

N

N

10

Y

N

Y

N


Table 4-13 Starting Positions for an STS-Mc SPE in an STM16 Signal 

VC Number
VC4 SPE
VC4-2C SPE
VC4-3C SPE
VC4-4C SPE
VC4-8C SPE
VC4-16C SPE

1

Y

Y

Y

Y

Y

Y

4

Y

Y

Y

N

Y

N

7

Y

Y

N

N

Y

N

10

Y

N

Y

N

Y

N

13

Y

Y

Y

Y

Y

N

16

Y

Y

Y

N

Y

N

19

Y

Y

Y

N

Y

N

22

Y

N

N

N

Y

N

25

Y

Y

Y

Y

Y

N

28

Y

Y

Y

N

N

N

31

Y

Y

N

N

N

N

34

Y

N

N

N

N

N

37

Y

Y

Y

Y

N

N

40

Y

Y

Y

N

N

N

43

Y

Y

N

N

N

N

46

Y

N

Y

N

N

N


Table 4-14 Starting positions for an STS-Mc SPE in an STM64 Signal 

VC Number
VC4 SPE
VC4-2C SPE
VC4-3C SPE
VC4-4C SPE
VC4-8C SPE
VC4-16C SPE
VC4-64C SPE

1

Y

Y

Y

Y

Y

Y

Y

4

Y

Y

Y

N

N

N

N

7

Y

Y

N

N

N

N

N

10

Y

N

Y

N

N

N

N

13

Y

Y

Y

Y

N

N

N

16

Y

Y

Y

N

N

N

N

19

Y

Y

Y

N

N

N

N

22

Y

N

N

N

N

N

N

25

Y

Y

Y

Y

N

N

N

28

Y

Y

Y

N

N

N

N

31

Y

Y

N

N

N

N

N

34

Y

N

N

N

N

N

N

37

Y

Y

Y

Y

N

N

N

40

Y

Y

Y

N

N

N

N

43

Y

Y

N

N

N

N

N

46

Y

N

Y

N

N

N

N

49

Y

Y

Y

Y

Y

Y

N

52

Y

Y

Y

N

N

N

N

55

Y

Y

Y

N

N

N

N

58

Y

N

N

N

N

N

N

61

Y

Y

Y

Y

N

N

N

64

Y

Y

Y

N

N

N

N

67

Y

Y

N

N

N

N

N

70

Y

N

N

N

N

N

N

73

Y

Y

Y

Y

N

N

N

76

Y

Y

Y

N

N

N

N

79

Y

Y

N

N

N

N

N

82

Y

N

Y

N

N

N

N

85

Y

Y

Y

Y

N

N

N

88

Y

Y

Y

N

N

N

N

91

Y

Y

Y

N

N

N

N

94

Y

N

N

N

N

N

N

97

Y

Y

Y

Y

Y

Y

N

100

Y

Y

Y

N

N

N

N

103

Y

Y

N

N

N

N

N

106

Y

N

N

N

N

N

N

109

Y

Y

Y

Y

N

N

N

112

Y

Y

Y

N

N

N

N

115

Y

Y

N

N

N

N

N

118

Y

N

Y

N

N

N

N

121

Y

Y

Y

Y

N

N

N

124

Y

Y

Y

N

N

N

N

127

Y

Y

Y

N

N

N

N

130

Y

N

N

N

N

N

N

133

Y

Y

Y

Y

N

N

N

136

Y

Y

Y

N

N

N

N

139

Y

Y

N

N

N

N

N

142

Y

N

N

N

N

Y

N

145

Y

Y

Y

Y

Y

N

N

148

Y

Y

Y

N

N

N

N

151

Y

Y

N

N

N

N

N

154

Y

N

Y

N

N

N

N

157

Y

Y

Y

Y

N

N

N

160

Y

Y

Y

N

N

N

N

163

Y

Y

Y

N

N

N

N

166

Y

N

N

N

N

N

N

169

Y

Y

Y

Y

N

N

N

172

Y

Y

Y

N

N

N

N

175

Y

Y

N

N

N

N

N

178

Y

N

N

N

N

N

N

181

Y

Y

Y

Y

N

N

N

184

Y

Y

Y

N

N

N

N

187

Y

Y

N

N

N

N

N

190

Y

N

Y

N

N

N

N


4.4  Conditions

Conditions include any problem detected on an ONS 15454 SDH shelf. They can include standing or transient, notifications. A snapshot of all current raised, standing conditions on the network, node, or card can be retrieved in the CTC Conditions window or using the RTRV-COND commands. (In addition, some but not all cleared conditions are also found in the History tab.)

Table 4-15 Conditions 

Condition
Description

AIS

Alarm Indication Signal

AIS-L

Alarm Indication Signal - Line

AIS-P

Alarm Indication Signal - Path

AIS-V

Alarm Indication Signal - VT

ALS

Automatic Laser Shutdown

APC-DISABLED

Automatic Power Control Disabled

APC-FAIL

Automatic Power Control Failure

APSB

Byte Failure

APSC-IMP

Improper APS Code

APSCDFLTK

Default K Byte

APSCINCON

Inconsistent APS Code

APSCM

Protection Switching Channel Match Failure

APSCNMIS

Node Id Mismatch

APSIMP

APS Invalid Mode

APSMM

Automatic Protection Switch Mode Mismatch

AS-CMD

Alarms Suppressed By User Command

AS-MT

Alarms Suppressed For Maintenance

AU-LOF

LOF - Administration Unit - Loss of Multi Frame

AUD-LOG-LOSS

Audit Log 100 Percent Full - Oldest records will be lost

AUD-LOG-LOW

Audit Log 80 Percent Full

AUTOLSROFF

Automatic Laser Shutoff Due To High Temperature

AUTORESET

Automatic System Reset

AUTOSW-AIS

Automatic SNCP Switch Caused By AIS

AUTOSW-LOP

Automatic SNCP Switch Caused By LOP

AUTOSW-PDI

Automatic SNCP Switch Caused By PDI

AUTOSW-SDBER

Automatic SNCP Switch Caused By SDBER

AUTOSW-SFBER

Automatic SNCP Switch Caused By SFBER

AUTOSW-UNEQ

Automatic SNCP Switch Caused By UNEQ

BAT-FAIL

Battery Failure

BKUPMEMP

Primary Non-Volatile Backup Memory Failure

MSSPROSYNC

MS-SPRing Out Of Sync

CARLOSS

Carrier Loss On The LAN

CKTDOWN

Signaling Unable to setup circuit

CLDRESTART

Cold Restart

COMIOXC

IO Slot To XCON Communication Failure

COMM-FAIL

Plug-in Module Communication Failure

CONTBUS-A-18

TCC A To DCC A Processor Communication Failure

CONTBUS-B-18

TCC B To DCC B Processor Communication Failure

CONTBUS_A

Controller A To Shelf Slot Communication Failure

CONTBUS_B

Controller B To Shelf Slot Communication Failure

CTNEQPT-MISMATCH

Connection Equipment Mismatch

CTNEQPT-PBPROT

Interconnection Equipment Failure - Protect XC Payload Bus

CTNEQPT-PBWORK

Interconnection Equipment Failure - Working XC Payload Bus

DATAFLT

Software Fault - Data Integrity Fault

DBOSYNC

Standby Database Out of Sync

DSP-COMM-FAIL

DSP Communication Failure

DSP-FAIL

DSP Failure

DUP-IPADDR

IP address already in use within the same DCC Area

DUP-NODENAME

Node name already in use within the same DCC Area

E-W-MISMATCH

Both Ends Of Fiber Provisioned As East Or Both As West

EHIBATVG

Extreme High Volt

ELWBATVG

Extreme Low Volt

EOC

SDCC Termination Failure

EOC-L

Line DCC Termination Failure

EQPT

Equipment Failure

EQPT-MISS

Replaceable Equipment/Unit is Missing

ERFI-P-CONN

Enhanced Remote Failure Indication - Path - Connectivity

ERFI-P-PAYLD

Enhanced Remote Failure Indication - Path - Payload

ERFI-P-SRVR

Enhanced Remote Failure Indication - Path - Server

ERROR-CONFIG

Error in Startup Config

ETH-LINKLOSS

Rear Panel Ethernet Link Removed

EXCCOL

Excess Collisions On The LAN

EXERCISE-RING-FAIL

Exercise Request on Ring Failed

EXERCISE-RING-REQ

Exercise Request on Ring

EXERCISE-SPAN-FAIL

Exercise Request on Span Failed

EXERCISE-SPAN-REQ

Exercise Request on Span

EXT

Failure Detected External To The NE

EXTRA-TRAF-PREEMPT

Extra Traffic Preempted

FAILTOSW

Failure To Switch To Protection

FAILTOSW-PATH

Failure To Switch To Protection - Path

FAILTOSWR

Failure To Switch To Protection - Ring

FAILTOSWS

Failure To Switch To Protection - Span

FAN

Fan Failure

FANDEGRADE

Partial Fan Failure

FE-AIS

Far End AIS

FE-EQPT-NSA

Far End Common Equipment Failure - Non Service Affecting

FE-EXERCISING-RING

Far End Exercising Ring

FE-EXERCISING-SPAN

Far End Exercising Span

FE-FRCDWKSWPR-RING

Far End Working Facility Forced To Switch To Protection - Ring

FE-FRCDWKSWPR-SPAN

Far End Working Facility Forced To Switch To Protection - Span

FE-IDLE

Far End IDLE

FE-LOCKOUTOFPR-SPAN

Far End Lockout Of Protection - Span

FE-LOF

Far End LOF

FE-LOS

Far End LOS

FE-MANWKSWPR-RING

Far End Manual Switch Of Working Facility To Protection - Ring

FE-MANWKSWPR-SPAN

Far End Manual Switch Of Working Facility To Protection - Span

FEC-MISM

FEC Mismatch

FEPRLF

Far End Protection Line Failure

FORCED-REQ

Forced Switch Request

FORCED-REQ-RING

Forced Switch Request On Ring

FORCED-REQ-SPAN

Forced Switch Request On Span

FRCDSWTOINT

Forced Switch To Internal Clock

FRCDSWTOPRI

Forced Switch To Primary Reference

FRCDSWTOSEC

Forced Switch To Second Reference

FRCDSWTOTHIRD

Forced Switch To Third Reference

FRNGSYNC

Free Running Synchronization Mode

FSTSYNC

Fast Start Synchronization Mode

FULLPASSTHR-BI

Bidirectional Full Pass Through Is Active

GCC-EOC

GCC Termination Failure

GE-OOSYNC

GigaBit Ethernet Out of Sync

HI-LASERBIAS

Equipment High Laser Bias

HI-RXPOWER

Equipment High Rx power

HI-TXPOWER

Equipment High Tx power

HIBATVG

High Volt

HITEMP

High Temperature

HLDOVRSYNC

Holdover Synchronization Mode

I-HITEMP

Industrial High Temperature

IMPROPRMVL

Improper Removal

INC-GFP-OUTOFFRAME

Out Of Frame Detected by GFP Receiver

INC-GFP-SIGLOSS

Client Signal Loss Frames Detected by GFP Receiver

INC-SIGLOSS

Incoming Signal Loss on Fibre Channel Interface

INC-SYNCLOSS

Incoming Synchronization Loss on Fibre Channel Interface

INC_GFP_SYNCLOSS

Client Synchronization Loss Frames Detected by GFP Receiver

INHSWPR

Inhibit Switch To Protect Request On Equipment

INHSWWKG

Inhibit Switch To Working Request On Equipment

INTRUSION-PSWD

Security Intrusion Attempt Detected - See Audit Log

INVMACADR

Invalid MAC Address

IOSCFGCOPY

Ios Config Copy In Progress

KB-PASSTHR

K Bytes Pass Through Is Active

KBYTE-APS-CHANNEL-FAILURE

Kbyte Channel Failure

LAN-POL-REV

Lan Connection Polarity Reversed

LASEREOL

Laser Approaching End of Life

LKOUTPR-S

Lockout Of Protection - Span

LMP-HELLODOWN

LMP Hello FSM to Control Channel down

LMP-NDFAIL

LMP Neighbor Discovery has failed

LO-RXPOWER

Equipment Low Rx power

LO-TXPOWER

Equipment Low Tx power

LOA

Loss of Alignment

LOC

Loss of Channel

LOCKOUT-REQ

Lockout Switch Request On Facility or Equipment

LOCKOUT-REQ-RING

Lockout Switch Request On Ring

LOF

Loss Of Frame

LOM

Loss of Multi-Frame

LOP-P

Loss Of Pointer - Path

LOP-V

Loss Of Pointer - VT

LOS

Loss Of Signal

LPBKCRS

Cross-connect Loopback

LPBKFACILITY

Facility Loopback

LPBKTERMINAL

Terminal Loopback

LWBATVG

Low Volt

MAN-REQ

Manual Switch Request

MANRESET

Manual System Reset

MANSWTOINT

Manual Switch To Internal Clock

MANSWTOPRI

Manual Switch To Primary Reference

MANSWTOSEC

Manual Switch To Second Reference

MANSWTOTHIRD

Manual Switch To Third Reference

MANUAL-REQ-RING

Manual Switch Request On Ring

MANUAL-REQ-SPAN

Manual Switch Request On Span

MEA

Mismatch Of Equipment And Attributes

MEM-GONE

Free Memory On Card Near Zero

MEM-LOW

Free Memory On Card Very Low

MFGMEM

Manufacturing Data Memory (EEPROM Failure

NO-CONFIG

No Startup Config

NTWTPINC

Network Topology Incomplete

OCHNC-ACTIV-FAIL

Optical Channel Activation Failure

OCHNC-DEACTIV-FAIL

Optical Channel De-Activation Failure

OCHNC-FAIL

Optical Channel Connection Failure

OCHNC-INC

Optical Channel Incomplete

ODUK-AIS-PM

ODUk: Alarm Indication Signal

ODUK-BDI-PM

ODUk: PM Backward Defect Indication

ODUK-LCK-PM

ODUk: Locked Defect - PM

ODUK-OCI-PM

ODUk: Open Connection Indication

ODUK-SD-PM

ODUk: Signal Degrade

ODUK-SF-PM

ODUk: Signal Failure

ODUK-TIM-PM

ODUk: Trail Trace Identifier Mismatch

OOU-TPT

Out of Use - Transport Failure

OPTNTWMIS

Optical Network Type Mismatch

OTUK-AIS

OTUk: Alarm Indication Signal

OTUK-BDI

OTUk: Backward Defect Indication

OTUK-LOF

OTUk: Loss Of Frame

OTUK-SD

OTUk: Signal Degrade

OTUK-SF

OTUk: Signal Failure

OTUK-TIM

OTUk: Trail Trace Identifier Mismatch

OUT-OF-SYNC

8B10B Out of Sync

PDI-P

Payload Defect Indication - Path

PEER-NORESPONSE

Peer Card Not Responding

PLM-P

Payload Label Mismatch - Path

PLM-V

Signal Label Mismatch Failure - Payload Label Mismatch - VT

PORT-CODE-MISM

Pluggable Port security code mismatch

PORT-COMM-FAIL

Module Communication Failure

PORT-MISMATCH

Pluggable Port rate mismatch

PORT-MISSING

Pluggable Port missing

PRC-DUPID

Duplicate Node ID

PROTNA

Protection Unit Not Available

PTIM

Payload Type Identifier Mismatch

PWR-REDUN

Redundant Power Capability Lost

RAI

Remote Alarm Indication

RCVR-MISS

Facility Termination Equipment - Receiver Missing

RFI

Remote Failure Indication

RFI-L

Remote Failure Indication - Line

RFI-P

One-Bit Remote Failure Indication - Path

RFI-V

Remote Failure Indication - VT

RING-ID-MIS

Ring Id Mismatch

RING-MISMATCH

Far End Of Fiber Is Provisioned With Different Ring ID

RING-SW-EAST

Ring Switch Is Active On The East Side

RING-SW-WEST

Ring Switch Is Active On The West Side

RSVP-HELLODOWN

RSVP Hello FSM to Neighbor down

RUNCFG-SAVENEED

Need to Save Running Config

SD

Signal Degrade

SD-L

BER Threshold Exceeded For Signal Degrade - Line

SD-P

BER Threshold Exceeded For Signal Degrade - Path

SF

Signal Failure

SF-L

BER Threshold Exceeded For Signal Failure - Line

SF-P

BER Threshold Exceeded For Signal Failure - Path

SFTWDOWN

Software Download In Progress

SNTP-HOST

SNTP Host Failure

SPAN-SW-EAST

Span Switch Is Active On The East Side

SPAN-SW-WEST

Span Switch Is Active On The West Side

SQM

Sequence Mismatch

SQUELCH

Ring Is Squelching Traffic

SQUELCHED

Equipment Squelched

SSM-DUS

Do Not Use For Synchronization

SSM-FAIL

Failed To Receive Synchronization Status Message

SSM-LNC

G812 - Local Node Clock traceable

SSM-OFF

Synchronization Status Messages Are Disabled On This Interface

SSM-PRC

G811 - Primary Reference Clock traceable

SSM-PRS

Stratum 1 Primary Reference Source Traceable

SSM-RES

Reserved For Network Synchronization Use

SSM-SDH-TN

G812 - Transit Node Clock traceable

SSM-SETS

G813 - Synchronous Equipment Timing Source traceable

SSM-SMC

SDH Minimum Clock Traceable

SSM-ST2

Stratum 2 Traceable

SSM-ST3

Stratum 3 Traceable

SSM-ST3E

Stratum 3E Traceable

SSM-ST4

Stratum 4 Traceable

SSM-STU

Synchronized - Traceability Unknown

SSM-TNC

Transit Node Clock Traceable

SWMTXMOD

Switching Matrix Module Failure

SWTOPRI

Switch To Primary Reference

SWTOSEC

Switch To Second Reference

SWTOTHIRD

Switch To Third Reference

SYNC-FREQ

Synchronization Reference Frequency Out Of Bounds

SYNCPRI

Primary Synchronization Reference Failure

SYNCSEC

Secondary Synchronization Reference Failure

SYNCTHIRD

Third Synchronization Reference Failure

SYSBOOT

System Reboot

TIM

TIM Section - Trace Identifier Mismatch Failure

TIM-MON

TIM Section Monitor - Trace Identifier Mismatch Failure

TIM-P

STS Path Trace Identifier Mismatch

TPTFAIL

Transport layer failure

TRMT

Transmit Failure

TRMT-MISS

Facility Termination Equipment - Transmitter Missing

TUNDERRUN

Ether tx underrun

TX-AIS

Alarm Indication Signal in TX

TX-RAI

Remote Alarm Indication in TX

UNC-WORD

FEC Uncorrected Word

UNEQ-P

Unequipped - Path

UNEQ-V

Signal Label Mismatch Failure - Unequipped VT

VCG-DEG

VCAT Group Degraded

VCG-DOWN

VCAT Group Down

WKSWPR

Switched To Protection

WTR

Wait To Restore

WVL-MISMATCH

Equipment Wavelength Mismatch


4.5  Access Identifiers

The AID code directs an input command to its intended physical or data entity inside the NE. Equipment modules and facilities are typical examples of entities addressed by the access code.

4.5.1  ALL

Table 4-16 ALL 

AID
Pattern

AidUnionId

FACILITY

VC

 

AidUnionId1

MS-SPRing

 

BAND

ALL

BAND-{1-6,12-17}-{1-4}-ALL

BAND-{1-6,12-17}-{1-4}-{RX,TX}

BAND-{1-6,12-17}-{1}-ALL

BAND-{1-6,12-17}-{1}-{RX,TX}

 

BITS

ALL

BITS-ALL

BITS-{1,2}

SYNC-BITS {1,2}

 

CHANNEL

ALL

CHAN-{1-6,12-17}-ALL

CHAN-{1-6,12-17}-{1-32}-ALL

CHAN-{1-6,12-17}-{1-32}-{RX,TX}

CHAN-{1-6,12-17}-{1-4}-ALL

CHAN-{1-6,12-17}-{1-4}-{RX,TX}

CHAN-{1-6,12-17}-{2,3}

CHAN-{1-6,12-17}-{2,5}

 

COM

Common

 

CrossConnectId

FACILITY

 

CrossConnectId1

VCM

FACILITY

VC

 

ENV

ALL

ENV-IN-ALL

ENV-IN-{1-20}

ENV-IN-{1-32}

ENV-IN-{1-3}

ENV-IN-{1-4}

ENV-IN-{1-6}

ENV-OUT-ALL

ENV-OUT-{1-16}

ENV-OUT-{1-2}

ENV-OUT-{1-4}

ENV-{IN,OUT}-{1-16}

EQPT

AIP

ALL

BIC-ALL

BIC-{A,B}

BP

FAN

PIM-{1-4,11-14}-ALL

PIM-{1-4,11-14}-{1-4}

PPM-1-{1,2}

PPM-2-{1,2}

PPM-{1-4,11-14}-{1-4}-ALL

PPM-{1-4,11-14}-{1-4}-{1-4}

PPM-{1-6,12-17}-{1-4}

PPM-{1-6,12-17}-{1-8}

PWR-ALL

PWR-{A,B}

SLOT-ALL

SLOT-{1-14}

SLOT-{1-17}

SLOT-{1-2}

SLOT-{1-4,11-14}

SLOT-{1-6,12-17}

SLOT-{1-8}

FACILITY

ALL

E1-{2}-{1-21}

E3-{2}-{1-3}

FAC-{1-4,11-14}-ALL

FAC-{1-4,11-14}-{1-16}

FAC-{1-4,11-14}-{1-4}

FAC-{1-4,11-14}-{1-4}-{1-4}-{1}

FAC-{1-4,14-17}-{1-8}

FAC-{1-4}-1

FAC-{1-4}-{1-4}

FAC-{1-6,12-17}-1

FAC-{1-6,12-17}-ALL

FAC-{1-6,12-17}-{0-11}

FAC-{1-6,12-17}-{0-1}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24,26,28,30,32,34,36}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24}

FAC-{1-6,12-17}-{1-12}

FAC-{1-6,12-17}-{1-4}

FAC-{1-6,12-17}-{1-6}

FAC-{1-6,12-17}-{1}

FAC-{1-6}-ALL

FAC-{5,6,12,13}-{1}

FAC-{5-6}-{1-28}

FAC-{5-6}-{1-3}

FAC-{8,10}-{1}

FSTE-{1}-{0-7}

FSTE-{1}-{1-8}

OC12-{2}-{1-2}-{1}

OC3-{2}-{1-2}-{1}

VFAC-{1-4,11-14}-{1-4}-{1-4}-1

VFAC-{1-6,12-17}-{0-1}

VFAC-{1-6,12-17}-{1,2}

VFAC-{1-6,12-17}-{1,2}-{1,8}

VFAC-{1}-{0-1}

VFAC-{1}-{1-8}

IPADDR

111.222.333.444

ALL

 

LINE

ALL

LINE-{1-6,12-17}-{1-2}-ALL

LINE-{1-6,12-17}-{1-2}-{RX,TX}

LINE-{1-6,12-17}-{1-3}-ALL

LINE-{1-6,12-17}-{1-3}-{RX,TX}

LINE-{8,10}-{1}-ALL

LINE-{8,10}-{1}-{RX,TX}

 

MS-SPRing

ALL

MSSPR-RINGID

 

OPM

OPM-{1-5,12-16}--{1530.33,1531.12,1531.90,1532.68,1534.25,1535.04,1535.82,

1536.61,1538.19,1538.98,1539.77,1540.56,1542.14,1542.94,1543.73,1544.53,

1546.12,1546.92,1547.72,1548.51,1550.12,1550.92,1551.72,1552.52,1554.13,

1554.94,1555.75,1556.55,1558.17,1558.98,1559.79,1560.61}

OSC

ALL

OSC-RINGID

 

PRSLOT

NULL

SLOT-1

SLOT-13

SLOT-15

SLOT-17

SLOT-3

SLOT-5

 

RFILE

RFILE-DB

RFILE-PKG

 

SYN

SYNC-NE

 

SYN_SRC

BITS-1

BITS-2

E1-{2}-{1-21}

FAC-{1-4,11-14}-{1-16}

FAC-{1-4,11-14}-{1-4}

FAC-{1-4}-1

FAC-{1-4}-{1-4}

FAC-{1-6,12-17}-{1-4}

FAC-{1-6,12-17}-{1}

FAC-{5,6,12,13}-{1}

INTERNAL

NONE

OC12-{2}-{1-2}-{1}

OC3-{2}-{1-2}-{1}

SYNC-NE

SYNC_REF

ALL

SYNC-ALL

SYNC-NE

SYNC-{BITS1,BITS2}

 

SYNCSW

INT

PRI

SEC

THIRD

 

UDC

ALL

UDC-{F,DCC}-{A,B}

 

VC

VC11-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC11-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-
{1-3}

VC11-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-14}-1-11{1-7}-{1-2}

VC11-{1-6,12-17}-{1-42}-1-{1-2}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-
{1-3}

VC12-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-1-{1-7}-{1-2}

VC12-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-2}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC3-{1-14,14-17}-{1-12}-1-{1-3}

VC3-{1-4,14-17}-{1-4}-{1-4}-{1-3}

VC3-{1-4,14-17}-{1-8}-1-{1-3}

VC3-{1-6,12-17}-1-{1-16}-{1-3}

VC3-{1-6,12-17}-1-{1-4}-{1-3}

VC3-{1-6,12-17}-{1-4}-1-{1-3}

VC3-{1-6,12-17}-{1-4}-{1-3}

VC4-{1-4,11-14}-{1-16}-1

VC4-{1-4,11-14}-{1-16}-{1,5,9,13}

VC4-{1-4,11-14}-{1-16}-{1,9}

VC4-{1-4,11-14}-{1-4}-1

VC4-{1-4,11-14}-{1-4}-{1,17,33,49}

VC4-{1-4,11-14}-{1-4}-
{1,5,9,13,17,21,25,29,33,37,41,45,49,53,57,61}

VC4-{1-4,11-14}-{1-4}-{1,9,17,25,33,41,49,57}

VC4-{1-4,11-14}-{1-4}-{1-64}

VC4-{1-4,14-17}-1

VC4-{1-4,14-17}-1-1

VC4-{1-4,14-17}-{1-12}-1

VC4-{1-4,14-17}-{1-4}-1

VC4-{1-4,14-17}-{1-4}-{1-2}

VC4-{1-4,14-17}-{1-4}-{1-3}

VC4-{1-4,14-17}-{1-4}-{1-4}

VC4-{1-4,14-17}-{1-8}-1

VC4-{1-6,12-17}-1

VC4-{1-6,12-17}-1-1

VC4-{1-6,12-17}-1
-{1,2,3,5,6,7,9,10,11,13,14,15}

VC4-{1-6,12-17}-1-{1,2,4,5,6,7,9,10,13,14}

VC4-{1-6,12-17}-1-{1,5,9,13}

VC4-{1-6,12-17}-1-{1-16}

VC4-{1-6,12-17}-1-{1-2}

VC4-{1-6,12-17}-1-{1-3}

VC4-{1-6,12-17}-1-{1-4}

VC4-{1-6,12-17}-1-{1-9}

VC4-{1-6,12-17}-{1-4}

VC4-{1-6,12-17}-{1-4}-1

WDMANS

AONS-{E,W}

WDMANS-{E,W}

 

WLEN

WLEN-{E,W}-{ADD,DROP,EXP}-{1530.33,1531.12,1531.90,1532.68,1534.25,1535.04,1535.82,1536.61,1538.19,1538.98,1539.77,1540.56,1542.14,1542.94,1543.73,1544.53,
1546.12,1546.92,,1547.72,1548.51,1550.12,1550.92,1551.72,1552.52,1554.13,1554.94,
1555.75,1556.55,1558.17,1558.98,1559.79,1560.61}


4.5.2  AidUnionId

Table 4-17 AidUnionId 

AID
Patterns
Facility

ALL

E1-{2}-{1-21}

E3-{2}-{1-3}

FAC-{1-4,11-14}-ALL

FAC-{1-4,11-14}-{1-16}

FAC-{1-4,11-14}-{1-4}

FAC-{1-4,11-14}-{1-4}-{1-4}-{1}

FAC-{1-4,14-17}-{1-8}

FAC-{1-4}-1

FAC-{1-4}-{1-4}

FAC-{1-6,12-17}-1

FAC-{1-6,12-17}-ALL

FAC-{1-6,12-17}-{0-11}

FAC-{1-6,12-17}-{0-1}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24,26,28,30,32,34,36}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24}

FAC-{1-6,12-17}-{1-12}

FAC-{1-6,12-17}-{1-4}

FAC-{1-6,12-17}-{1-6}

FAC-{1-6,12-17}-{1}

FAC-{1-6}-ALL

FAC-{5,6,12,13}-{1}

FAC-{5-6}-{1-28}

FAC-{5-6}-{1-3}

FAC-{8,10}-{1}

FSTE-{1}-{0-7}

FSTE-{1}-{1-8}

STM4-{2}-{1-2}-{1}

STM1-{2}-{1-2}-{1}

VFAC-{1-4,11-14}-{1-4}-{1-4}-1

VFAC-{1-6,12-17}-{0-1}

VFAC-{1-6,12-17}-{1,2}

VFAC-{1-6,12-17}-{1,2}-{1,8}

VFAC-{1}-{0-1}

VFAC-{1}-{1-8}

VC

VC11-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC11-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC11-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-14}-1-11{1-7}-{1-2}

VC11-{1-6,12-17}-{1-42}-1-{1-2}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-1-{1-7}-{1-2}

VC12-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-2}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC3-{1-14,14-17}-{1-12}-1-{1-3}

VC3-{1-4,14-17}-{1-4}-{1-4}-{1-3}

VC3-{1-4,14-17}-{1-8}-1-{1-3}

VC3-{1-6,12-17}-1-{1-16}-{1-3}

VC3-{1-6,12-17}-1-{1-4}-{1-3}

VC3-{1-6,12-17}-{1-4}-1-{1-3}

VC3-{1-6,12-17}-{1-4}-{1-3}

VC4-{1-4,11-14}-{1-16}-1

VC4-{1-4,11-14}-{1-16}-{1,5,9,13}

VC4-{1-4,11-14}-{1-16}-{1,9}

VC4-{1-4,11-14}-{1-4}-1

VC4-{1-4,11-14}-{1-4}-{1,17,33,49}

VC4-{1-4,11-14}-{1-4}-
{1,5,9,13,17,21,25,29,33,37,41,45,49,53,57,61}

VC4-{1-4,11-14}-{1-4}-{1,9,17,25,33,41,49,57}

VC4-{1-4,11-14}-{1-4}-{1-64}

VC4-{1-4,14-17}-1

VC4-{1-4,14-17}-1-1

VC4-{1-4,14-17}-{1-12}-1

VC4-{1-4,14-17}-{1-4}-1

VC4-{1-4,14-17}-{1-4}-{1-2}

VC4-{1-4,14-17}-{1-4}-{1-3}

VC4-{1-4,14-17}-{1-4}-{1-4}

VC4-{1-4,14-17}-{1-8}-1

VC4-{1-6,12-17}-1

VC4-{1-6,12-17}-1-1

VC4-{1-6,12-17}-1-
{1,2,3,5,6,7,9,10,11,13,14,15}

VC4-{1-6,12-17}-1-{1,2,4,5,6,7,9,10,13,14}

VC4-{1-6,12-17}-1-{1,5,9,13}

VC4-{1-6,12-17}-1-{1-16}

VC4-{1-6,12-17}-1-{1-2}

VC4-{1-6,12-17}-1-{1-3}

VC4-{1-6,12-17}-1-{1-4}

VC4-{1-6,12-17}-1-{1-9}

VC4-{1-6,12-17}-{1-4}

VC4-{1-6,12-17}-{1-4}-1


4.5.3  AidUnionId1

Table 4-18 AidUnionId1 

AID
Patterns

MS-SPRing

ALL

MSSPR-RINGID


4.5.4  BAND

The BAND AID is used to access Optical Multiplex Section (OMS) layer of Optical Network units.

Table 4-19 BAND 

Pattern
Description

ALL

All of the OMSs of the NE. The ALL AID is applicable for retrieve-only commands

BAND-{1-6,12-17}-{1-4}-ALL

All the Channels in a Band OADM (1Bn, 4Bn) units

BAND-{1-6,12-17}-{1-4}-{RX,TX}

The Receive/Transmit Channels in a Band OADM (1Bn, 4Bn) units

BAND-{1-6,12-17}-{1}-ALL

All the Channels in an Optical Multiplexer/Demultiplexer (4Ch) units

BAND-{1-6,12-17}-{1}-{RX,TX}

The Receive/Transmit Channels in an Optical Multiplexer/Demultiplexer (4Ch) units


4.5.5  BITS

AID for BITS (Building Integrated Timing Supply).

Table 4-20 BITS 

Pattern
Description

ALL

The ALL AID is applicable to RTRV commands only (RTRV-BITS and RTRV-ALM/COND-BITS). The All AID is equivalent to BITS-ALL for these commands. For RTRV-ALM/COND-SYNCN, the ALL AID translates to BITS-ALL, SYNC-BITS1, and SYNC-BITS2

BITS-ALL

BITS AIDS of both BITS-1 and BITS-2 in the RTRV-BITS command

BITS-{1,2}

Individual BITS AID

SYNC-BITS{1,2}

BITS-OUT AIDs of BITS-1 and BITS-2. These AIDs are applicable only in ED/RTRV-BITS commands and are used for setting and retrieving the BITS-OUT parameters.


4.5.6  CHANNEL

Accesses the Optical Channels (OCH) layer of Optical Network/Client units.

Table 4-21 CHANNEL 

CHANNEL Values
Description

ALL

ALL OCHs of the NE. The ALL AID is applicable for retrieve-only commands

CHAN-{1-6,12-17}-ALL

All the Channels of an Optical Transponder/Muxponder. The format is CHAN-[SLOT]-ALL

CHAN-{1-6,12-17}-{1-32}-ALL

All the Channels in an Optical Multiplexer/Demultiplexer (32Ch) units. The format is CHAN-[SLOT]-[PORT]-ALL

CHAN-{1-6,12-17}-{1-32}-{RX,TX}

The Receive/Transmit Channels in an Optical Multiplexer/Demultiplexer (32Ch) units. The format is CHAN-[SLOT]-[PORT]-[DIRECTION]

CHAN-{1-6,12-17}-{1-4}-ALL

All the Channels in an OADM (1Ch, 2Ch, 4Ch) units and Optical and Optical Multiplexer/Demultiplexer (4Ch) units. The format is CHAN-[SLOT]-[PORT]-ALL

CHAN-{1-6,12-17}-{1-4}-{RX,TX}

The Receive/Transmit Channels in an OADM (1Ch, 2Ch, 4Ch) units and Optical Multiplexer/Demultiplexer (4Ch) units. The format is CHAN-[SLOT]-[PORT]-[DIRECTION]

CHAN-{1-6,12-17}-{2,3}

A single channel of an Optical Transponder/Muxponder. The TXP_MR_10G and TXP_MR_2.5G use CHAN-slot-2 for the 1 DWDM Facility. TXPP_MR_2.5G uses CHAN-slot-{2,3} for the 2 DWDM facilities. The format is CHAN-[SLOT]-[PORT]

CHAN-{1-6,12-17}-{2,5}

A single channel of an Optical Transponder/Muxponder. The TXP_MR_10G uses CHAN-slot-2 for the 1 DWDM facility. MXP_2.5G_10G uses the CHAN-slot-5 for the 1 DWDM facility. The format is CHAN-[SLOT]-[PORT]


4.5.7  COM

Common

Table 4-22 COM 

Pattern
Description

COM

Common


4.5.8  CrossConnectId

Table 4-23 CrossConnectId 

AID
Pattern

FACILITY

ALL

E1-{2}-{1-21}

E3-{2}-{1-3}

FAC-{1-4,11-14}-ALL

FAC-{1-4,11-14}-{1-16}

FAC-{1-4,11-14}-{1-4}

FAC-{1-4,11-14}-{1-4}-{1-4}-{1}

FAC-{1-4,14-17}-{1-8}

FAC-{1-4}-1

FAC-{1-4}-{1-4}

FAC-{1-6,12-17}-1

FAC-{1-6,12-17}-ALL

FAC-{1-6,12-17}-{0-11}

FAC-{1-6,12-17}-{0-1}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24,26,28,30,32,34,36}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24}

FAC-{1-6,12-17}-{1-12}

FAC-{1-6,12-17}-{1-4}

FAC-{1-6,12-17}-{1-6}

FAC-{1-6,12-17}-{1}

FAC-{1-6}-ALL

FAC-{5,6,12,13}-{1}

FAC-{5-6}-{1-28}

FAC-{5-6}-{1-3}

FAC-{8,10}-{1}

FSTE-{1}-{0-7}

FSTE-{1}-{1-8}

STM4-{2}-{1-2}-{1}

STM1-{2}-{1-2}-{1}

Facility (continued)

VFAC-{1-4,11-14}-{1-4}-{1-4}-1

VFAC-{1-6,12-17}-{0-1}

VFAC-{1-6,12-17}-{1,2}

VFAC-{1-6,12-17}-{1,2}-{1,8}

VFAC-{1}-{0-1}

VFAC-{1}-{1-8}


4.5.9  CrossConnectId1

Table 4-24 CrossConnectId1 

AID
Pattern

VCM

VCM-{1-6,12-17}-{0-1}-ALL

VCM-{1-6,12-17}-{0-1}-{1-256}

VCM-{1-6,12-17}-{1-4}-ALL

VCM-{1-6,12-17}-{1-4}-{1-256}

FACILITY

ALL

E1-{2}-{1-21}

E3-{2}-{1-3}

FAC-{1-4,11-14}-ALL

FAC-{1-4,11-14}-{1-16}

FAC-{1-4,11-14}-{1-4}

FAC-{1-4,11-14}-{1-4}-{1-4}-{1}

FAC-{1-4,14-17}-{1-8}

FAC-{1-4}-1

FAC-{1-4}-{1-4}

FAC-{1-6,12-17}-1

FAC-{1-6,12-17}-ALL

FAC-{1-6,12-17}-{0-11}

FAC-{1-6,12-17}-{0-1}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24,26,28,30,32,34,36}

FAC-{1-6,12-17}-{1-12,14,16,18,20,22,24}

FAC-{1-6,12-17}-{1-12}

FAC-{1-6,12-17}-{1-4}

FAC-{1-6,12-17}-{1-6}

FAC-{1-6,12-17}-{1}

FAC-{1-6}-ALL

FAC-{5,6,12,13}-{1}

FAC-{5-6}-{1-28}

FAC-{5-6}-{1-3}

FAC-{8,10}-{1}

FSTE-{1}-{0-7}

FSTE-{1}-{1-8}

STM4-{2}-{1-2}-{1}

STM1-{2}-{1-2}-{1}

VFAC-{1-4,11-14}-{1-4}-{1-4}-1

VFAC-{1-6,12-17}-{0-1}

VFAC-{1-6,12-17}-{1,2}

VFAC-{1-6,12-17}-{1,2}-{1,8}

VFAC-{1}-{0-1}

VFAC-{1}-{1-8}

VC

VC11-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC11-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC11-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-14}-1-11{1-7}-{1-2}

VC11-{1-6,12-17}-{1-42}-1-{1-2}-{1-7}-{1-3}

VC11-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC12-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-1-{1-7}-{1-2}

VC12-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-2}-{1-7}-{1-3}

VC12-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC12-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC3-{1-14,14-17}-{1-12}-1-{1-3}

VC3-{1-4,14-17}-{1-4}-{1-4}-{1-3}

VC3-{1-4,14-17}-{1-8}-1-{1-3}

VC3-{1-6,12-17}-1-{1-16}-{1-3}

VC3-{1-6,12-17}-1-{1-4}-{1-3}

VC3-{1-6,12-17}-{1-4}-1-{1-3}

VC

VC3-{1-6,12-17}-{1-4}-{1-3}

VC4-{1-4,11-14}-{1-16}-1

VC4-{1-4,11-14}-{1-16}-{1,5,9,13}

VC4-{1-4,11-14}-{1-16}-{1,9}

VC4-{1-4,11-14}-{1-4}-1

VC4-{1-4,11-14}-{1-4}-{1,17,33,49}

VC4-{1-4,11-14}-{1-4}-{1,5,9,13,17,21,25,29,33,37,41,45,49,53,57,61}

VC4-{1-4,11-14}-{1-4}-{1,9,17,25,33,41,49,57}

VC4-{1-4,11-14}-{1-4}-{1-64}

VC4-{1-4,14-17}-1

VC4-{1-4,14-17}-1-1

VC4-{1-4,14-17}-{1-12}-1

VC4-{1-4,14-17}-{1-4}-1

VC4-{1-4,14-17}-{1-4}-{1-2}

VC4-{1-4,14-17}-{1-4}-{1-3}

VC4-{1-4,14-17}-{1-4}-{1-4}

VC4-{1-4,14-17}-{1-8}-1

VC4-{1-6,12-17}-1

VC4-{1-6,12-17}-1-1

VC4-{1-6,12-17}-1-{1,2,3,5,6,7,9,10,11,13,14,15}

VC4-{1-6,12-17}-1-{1,2,4,5,6,7,9,10,13,14}

VC4-{1-6,12-17}-1-{1,5,9,13}

VC4-{1-6,12-17}-1-{1-16}

VC4-{1-6,12-17}-1-{1-2}

VC4-{1-6,12-17}-1-{1-3}

VC4-{1-6,12-17}-1-{1-4}

VC4-{1-6,12-17}-1-{1-9}

VC4-{1-6,12-17}-{1-4}

VC4-{1-6,12-17}-{1-4}-1


4.5.10  ENV

The environmental AID for the AICI cards

Table 4-25 ENV 

Pattern
Description

ALL

The ALL AID applies to retrieve-only commands: RTRV-ALM/COND-ENV, RTRV-ATTR-CONT and RTRV-ATTR-ENV

ENV-IN-ALL

Environmental AID for ALL Environmental alarms

ENV-IN-{1-4}

Environmental AID for the AIC Card. "IN" is used for Environmental Alarms

ENV-IN-{1-20}

Environmental AID for the AICI Card. "IN" is used for Environmental Alarms

ENV-IN-{1-32}

Environmental AID for AICI Card Extensions. "IN" is used for Environmental Alarms

ENV-IN-{1-16}

Environmental AID. "IN" is used for Environmental Alarms

ENV-OUT-{1-4}

Environmental AID for the AIC/AICI Cards. "OUT" is used for Environmental Controls

ENV-OUT-{1-16}

Environmental AID for AICI Card Extensions. "OUT" is used for Environmental Controls


4.5.11  EQPT

Equipment AIDs are used to access specific cards.

Table 4-26 EQPT 

Pattern
Description

AIP

The AID for the AIP. It is used for RTRV-INV output only

ALL

Only used for RTRV-INV, RTRV-EQPT, and RTRV-ALM/COND-EQPT commands. RTRV-INV returns all the inventory information for the NE. Includes the I/O cards, controller cards, and the AIP, BP, and FAN

BIC-ALL

AIDs for the BIC (Backplane Interface Connector), BIC-A and BIC-B. These AIDs are valid only for the RTRV-ALM-EQPT and RTRV-COND-EQPT commands

BIC-{A,B}

AIDs for the BIC (Backplane Interface Connectors). These AIDs are valid only for the RTRV-ALM-EQPT and RTRV-COND-EQPT commands

BP

The AID for the backplane. It is used for RTRV-INV output only

FAN

The AID for the fan tray. It is used for RTRV-INV output only

PPM-{1-6,12-17}-{1-4}

PPM AID for DWDM MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_2.5G_10E, and TXP_MR_10E Cards. Format of AID is PPM-[SLOT]-[PPM]

PPM-{1-6,12-17}-{1-8}

PPM AID for the ONS 15454 MXP_MR_2.5G and MXPP_MR_2.5G Card. Format of AID is PPM-[SLOT]-[PPM]

PWR-ALL

AIDs for the Power Supply Sources. These AIDs are valid only for the RTRV-ALM-EQPT and RTRV-COND-EQPT commands.

PWR-{A,B}

AIDs for the Power Supply Sources. These AIDs are valid only for the RTRV-ALM-EQPT and RTRV-COND-EQPT commands.

SLOT-ALL

All of the NE equipment AIDs

SLOT-{1-17}

EQPT AID where format is SLOT-[SLOT]

SLOT-{1-6,12-17}

Individual equipment AID of the I/O card units or slots where format is SLOT-[SLOT]


4.5.12  FACILITY

Facilities AIDs are used to access specific ports.

Facility AID format:

Format for DSi-N-12 Electrical Facilities: FAC-[SLOT]-[PORT]

Format for POS Ports: VFAC-[SLOT]-[PORT]

Format for POS Port with PIM and PPM:VFAC-[SLOT]-[PIM]-[PPM]-[PORT]

Table 4-27 FACILITY 

Pattern
Description

ALL

The ALL AID is applicable for RTRV-only commands (RTRV-rr type of commands), for example: RTRV-STM16 with ALL AID returns all STM16 facilities on the node

FAC-{1-4,14-17}-{1-8}

Facilities for an STM1 card where the format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-1

Facility AID for the 1 Client (CLNT) Port on a TXP_MR_10G, TXP_MR_2.5G, TXP_MR_2.5G or TXPP_MR_2.5G card where the format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-ALL

All the facilities of an I/O unit or slot where the format is FAC-[SLOT]-[ALL]

FAC-{1-6,12-17}-{0-11}

Facilities for the Ethernet Front-end ports on the ML100T-12 card. Ports are numbered starting with 0 (i.e. the first port is FAC-SLOT-0, second port is FAC-SLOT-1, ..., last port is FAC-SLOT-11 for ML100T-12 and first port is FAC-SLOT-0 and second port is FAC-SLOT-1 for ML1000-2). The format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{0-1}

Facilities for the Ethernet Backend Ports on the ML1000-2 card. Ports are 0-based, (i.e the first port is FAC-SLOT-0 and the second port is FAC-SLOT-1). The format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{1-12,14,16,18,
20,22,24,26,28,30,32,34,36}

Facility AIDs for the DS3i-N-12 VC416 Backplane Rate where format is FAC-[SLOT]-[PORT]. Ports 1 through 12 are always available, but only even ports after 12 are available

FAC-{1-6,12-17}-{1-12,14,16,18,
20,22,24}

Facility AIDs for DS3i-N-12 VC44 Backplane Rate where format is FAC-[SLOT]-[PORT]. Ports 1 through 12 are always available, but only even ports after 12 are available

FAC-{1-6,12-17}-{1-4}

Facility AID for the four Client (CLNT) facilities on the MXP_2.5G_10G card. Facility AID for 4-Port G1000/FC_MR-4 Card. Facility AID for creating/editing cross-connects (STS1/VC3, STS3C/VC4, STS6C/VC4-2C, STS9C/VC4-3C, STS12C/VC4-4C, and STS24C/VC4-8C) for the 4-Port G1000/FC_MR-4 Card where format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{1-6}

Facilities for the DS3i-N-12 card where format FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{1}

Facility AID for the 1-Port STM4, STM16 and STM1 in OSC-CSM cards. Facility AID for the client ports on the MXP/TXP and TXP_MR_2.5G cards where format is FAC-[SLOT]-[PORT]

FAC-{5,6,12,13}-{1}

Facility AID for the STM16/STM64 cards. The STM16/STM64 cards can only use the high speed slots (Slot 5, Slot 6, Slot 12, Slot 13) where format is FAC-[SLOT]-[PORT]

FAC-{8,10}-{1}

Facility AID for the OSCM card. The OSCM cards can only use the XC10G slots (Slot-8, Slot-10) where format is FAC-[SLOT]-[PORT]

VFAC-{1-6,12-17}-{0-1}

Facilities for the back end POS ports on the ML-Series card. Port numbering is 0-based (first POS port is VFAC-SLOT-0, second POS port is VFAC-SLOT-1). VC4, VC4-2C, VC4-3C, VC4-4C, VC4-8C for the ML1000 and ML100T Cards. Format is VFAC-[SLOT]-[PORT]

VFAC-{1-6,12-17}-{1,2}

GFP facilities on the MXP-MR-2.5G and MXPP-MR-2.5G card

VFAC-{1-6,12-17}-{1,2}-{1,8}

GFP Client facilities for MXP-MR-2.5G and MXPP-MR-2.5G cards


4.5.13  IPADDR

IP Address

Table 4-28 IPADDR 

Pattern
Description

111.222.333.444

Standard 4 Part IP Address Notation

ALL

ALL


4.5.14  LINE

The LINE AID is used to access the Optical Transport Section (OTS) layer of optical network units. Applicable only to ONS 15454 AD-1B-xx.x, AD-4B-xx.x, AD-1C-xx.x, AD-2C-xx.x, AB-4C-xx.x, OSC-CSM, OSCM, OPT-BST, OPT-PRE, 4MD-xx.x, 32MUX-O and 32DMX-O cards. The format is LINE-[SLOT]-[PORT]-[DIRECTION].

Table 4-29 LINE 

Values
Description

ALL

All of the OTSs of the NE. The ALL AID applies for retrieve-only commands

LINE-{1-6,12-17}-{1-2}-ALL

All the Lines in a OPT-PRE, OCS-CSM, AD-1B, AD-4B, AD-1C, AD-2C, AD-4C units

LINE-{1-6,12-17}-{1-2}-{RX,TX}

The receive/transmit Lines in a OPT-PRE, OCS-CSM, AD-1B, AD-4B, AD-1C, AD-2C, AD-4C units

LINE-{1-6,12-17}-{1-3}-ALL

All the Lines in a OPT-BST units

LINE-{1-6,12-17}-{1-3}-{RX,TX}

The receive/transmit Lines in a OPT-BST units

LINE-{8,10}-{1}-ALL

All the Lines in a OSCM units

LINE-{8,10}-{1}-{RX,TX}

The receive/transmit Lines in an OSCM units


4.5.15  LNKTERM

Link Termination AIDs that are used to access the termination points of a provisionable patchcord.

Table 4-30 LNKTERM 

Pattern
Description

ALL

Indicates all the provisionable patchcord terminations on a node. Applicable only for the retrieve commands

LNKTERM-ALL

Indicates all the provisionable patchcord terminations on a node. Applicable only for the retrieve commands

LNKTERM-{1-65535}

Indicates a single provisionable patchcord termination point on a node. Where format is LNKTERM-


4.5.16  MSSPR

MS-SPRing AIDs are used to access the MS-SPRing of the NE.

Table 4-31 MSSPR 

Pattern
Description

ALL

ALL AID for all MS-SPRings in the NE. The ALL AID is applicable for retrieve-only commands like RTRV-MSSPR, RTRV-ALM/COND-MSSPR

MSSPR-RINGID

MS-SPRing AID is keyword MS-SPRing followed by RingId. RingId is a string of up to 6-Characters, valid characters are ['A'-'Z','0'-'9'] (case insensitive)


4.5.17  OPM

OPM AIDs represent the single wavelength inside an optical power monitoring object

Table 4-32 OPM

Values
Description

OPM-{1-5,12-16}--{1530.33,1531.12,
1531.90,1532.68,1534.25,1535.04,
1535.82,1536.61,1538.19,1538.98,
1539.77,1540.56,1542.14,1542.94,
1543.73,1544.53,1546.12,1546.92,
1547.72,1548.51,1550.12,1550.92,
1551.72,1552.52,1554.13,1554.94,
1555.75,1556.55,1558.17,1558.98,
1559.79,1560.61}

The second index is the slot where the 32-WSS unit is configured. The last index of the wavelength is the value of the wavelength as described in OPTICAL_WLEN


4.5.18  OSC

OSC AIDs are used to access the OSC of the NE

Table 4-33 OSC 

Values
Description

ALL

All of the OSCs of the NE. The ALL AID applies to the retrieve-only commands

OSC-RINGID

RINGID is a string of up to six characters, valid characters are [A-Z,0-9] (case insensitive)


4.5.19  PRSLOT

Valid protection slots for the electrical cards. Format is SLOT-[SLOT].

Table 4-34 PRSLOT 

Pattern
Description

NULL

Indicates there is no protection group. Used when trying to delete a protection group.

SLOT-1

The No.1 slot of an NE

SLOT-3

The No.3 slot of an NE

SLOT-5

The No.5 slot of an NE

SLOT-13

The No.13 slot of an NE

SLOT-15

The No.15 slot of an NE

SLOT-17

The No.17 slot of an NE


4.5.20  RFILE

File transfer type.

Table 4-35 RFILE

Pattern
Description

RFILE-DB

Transferring the system database

RFILE-PKG

Transferring a software package


4.5.21  SYN

Synchronization AIDs

Table 4-36 SYN 

Pattern
Description

SYNC-NE

NE sync AID


4.5.22  SYN_SRC

Synchronization source

Table 4-37 SYN_SRC 

Pattern
Description

BITS-1

Sync source is BITS-1. Format is BITS-[PORT]

BITS-2

Sync source is BITS-2. Format is BITS-[PORT]

FAC-{1-4,11-14}-{1-4}

Sync source is 4-Port STM64. Format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{1-4}

Sync source is the optical card (STM1 and STM4) facility. Format is FAC-[SLOT]-[PORT]

FAC-{1-6,12-17}-{1}

Sync source is the optical card (STM1 and STM4) facility. Format is FAC-[SLOT]-[PORT]

FAC-{5,6,12,13}-{1}

Sync source is the optical card (STM16 and STM 64) facility. Format is FAC-[SLOT]-[PORT]

INTERNAL

Set the SYN_SRC to be the system default value. The "Internal" value of the SYN_SRC is only applied for the SYNC-NE AID on the ED-SYNCN command

NONE

Set the SYNC_SRC value to the default value for BITS-OUT. The "NONE" value of SYNC_SRC only applies to the BITS-1 and BITS-2 AID of the ED-SYNCN command

SYNC-NE

SYNC-NE source. It is only used in the alarm report or alarm retrieve commands.


4.5.23  SYNC_REF

Synchronization AIDs

Facility AID format for line timing:

Format for Optical Facilities Without PPM: FAC-[SLOT]-[PORT]

Format for Optical Facilities With PPM: FAC-[slot]-[PPM]-[PORT]

Table 4-38 SYNC_REF 

Pattern
Description

ALL

Equivalent to a combination of SYNC-ALL, BITS-1 and BITS-2. This AID is valid only for the commands RTRV-SYNCN, RTRV-ALM-SYNCN and RTRV-COND-SYNCN

SYNC-ALL

All synchronization references

SYNC-NE

NE sync AID

SYNC-{BITS1,BITS2}

BITS1 and BITS2 sync AIDs


4.5.24  SYNCSW

Synchronization reference

Table 4-39 SYNCSW 

Pattern
Description

INT

Internal clock. The "INT" value of the syncsw is only applied for the SYNC-NE AID on the OPR-SYNCSW command.

PRI

Primary timing reference

SEC

Secondary timing reference

THIRD

Third timing reference


4.5.25  UDC

UDC AIDs for F-UDC and DCC-UDC channels on the AICI card.

Table 4-40 UDC 

Pattern
Description

ALL

ALL AID is applicable to RTRV-only commands, for example: RTRV-ALM/COND-UDCF and RTRV-ALM/COND-UDCDCC. It corresponds to a superset of F-UDC and DCC-UDC AIDs

UDC-{F,DCC}-{A,B}

F-UDC and DCC-UDC AIDs for A and B channels


4.5.26  VC

SDH Frame Level AID Set.

VC4 AID Formats

For Optical Facilities: VC4-[SLOT]-[PORT]-[VC4]

For Electrical Facilities: VC4-[SLOT]-[VC4]

VC3 AID Formats

For Optical Facilities: VC3-[SLOT]-[PORT]-[VC4]-[VC3]

For Electrical Facilities: VC3-[SLOT]-[VC4]-[VC3]

VC12 AID Formats

For Optical Facilities: VC12-[SLOT]-[PORT]-[VC4]-[VC3]-[TUG2]-[VC12]

For Electrical Facilities: VC12-[SLOT]-[VC4]-[VC3]-[TUG2]-[VC12]

VC11 AID Formats

For Optical Facilities: VC11-[SLOT]-[PORT]-[VC4]-[VC3]-[TUG2]-[VC11]

For Electrical Facilities: VC11-[SLOT]-[VC4]-[VC3]-[TUG2]-[VC11]

Table 4-41 VC 

Pattern
Description

VC11-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC11 for the STM1E-12 card

VC11-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC11 for STM4-4

VC11-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC11 for STM1-8 card

VC11-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC11 for STM16 card

VC11-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC11 for STM4 card

VC11-{1-6,12-17}-{1-14}-1-11{1-7}-{1-2}

VC11 for the E1 card

VC11-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC11 for the STM1

VC12-{1-4,14-17}-{1-12}-1-{1-3}-{1-7}-{1-3}

VC12 for the STM1E-12 card

VC12-{1-4,14-17}-{1-4}-{1-4}-{1-3}-{1-7}-{1-3}

VC12 for STM4-4 card

VC12-{1-4,14-17}-{1-8}-1-{1-3}-{1-7}-{1-3}

VC12 for STM1-8

VC12-{1-6,12-17}-1-1-{1-7}-{1-2}

VC12 AIDs for the E1 Card

VC12-{1-6,12-17}-1-{1-16}-{1-3}-{1-7}-{1-3}

VC12 for STM16 card

VC12-{1-6,12-17}-1-{1-2}-{1-7}-{1-3}

VC12 for E1-42

VC12-{1-6,12-17}-1-{1-4}-{1-3}-{1-7}-{1-3}

VC12 for STM4 card

VC12-{1-6,12-17}-{1-4}-1-{1-3}-{1-7}-{1-3}

VC12 for STM1 card

VC3-{1-14,14-17}-{1-12}-1-{1-3}

VC3 for the STM1E-12 card

VC3-{1-4,14-17}-{1-4}-{1-4}-{1-3}

VC3 for the STM4-4 card

VC3-{1-4,14-17}-{1-8}-1-{1-3}

VC3 for the STM1-8 card

VC3-{1-6,12-17}-1-{1-16}-{1-3}

VC3 for the STM16 card

VC3-{1-6,12-17}-1-{1-4}-{1-3}

VC3 for the STM4 card

VC3-{1-6,12-17}-{1-4}-1-{1-3}

VC3 for the STM1 card

VC3-{1-6,12-17}-{1-4}-{1-3}

VC3 AID for DS3i-N-12 and E3 card

VC4-{1-4,14-17}-1

VC4 for E1-42 card

VC4-{1-4,14-17}-1-1

VC4 for STM1-8 card

VC4-{1-4,14-17}-{1-12}-1

VC4 for the STM1E-12 card

VC4-{1-4,14-17}-{1-4}-1

VC4 for the STM4 cardVC4-4C for the STM4-4 card

VC4-{1-4,14-17}-{1-4}-{1-2}

VC4-3C for the STM4-4 card

VC4-{1-4,14-17}-{1-4}-{1-3}

VC4-2C for the STM4-4 card

VC4-{1-4,14-17}-{1-4}-{1-4}

VC4 for the STM4-4 card

VC4-{1-4,14-17}-{1-8}-1

VC4 for the STM1-8 card

VC4-{1-6,12-17}-1

VC4 for E1 card

VC4-{1-6,12-17}-1-1

VC4-4C for the STM4 card. VC4-16C for the STM16 card

VC4-{1-6,12-17}-1-{1,2,3,5,6,7,9,10,11,13,14,15}

VC4-2C for the STM16 card

VC4-{1-6,12-17}-1-{1,2,4,5,6,7,9,10,13,14}

VC4-3C for the STM16

VC4-{1-6,12-17}-1-{1,5,9,13}

VC4-4C for the STM16 card

VC4-{1-6,12-17}-1-{1-16}

VC4 for the STM16 card

VC4-{1-6,12-17}-1-{1-2}

VC4-3C for the STM4 card

VC4-{1-6,12-17}-1-{1-3}

VC4-2C for the STM4 card

VC4-{1-6,12-17}-1-{1-4}

VC4 for the STM4 card

VC4-{1-6,12-17}-1-{1-9}

VC4-8C for the STM16 card (454)

VC4-{1-6,12-17}-{1-4}

VC4 for DS3i-N-12, E3, G1000 cards

VC4-{1-6,12-17}-{1-4}-1

VC4 for STM1 card


4.5.27  WDMANS

This AID is used to access the AONS application of the NE.

Table 4-42 WDMANS 

Pattern
Description

AONS-{E,W}

Automatic Optical Node Setup identifier (is per ring direction based)

WDMANS-{E,W}

Automatic Optical Node Setup identifier (is per ring direction based)


4.5.28  WLEN

This AID represents the single wavelength inside an external facility. If the facility is of type OTS (line) the wavelengths contained are all the available in the node: currently 32. If the facility is of type OCH (CHAN) the wavelength is just one and it is the same of the correspondent wavelength customized for that channel.

Table 4-43 WLEN 

Pattern
Description

WLEN-{E,W}-{ADD,DROP,EXP}-{1530.33,1531.12,1531.90,
1532.68,1534.25,1535.04,1535.82,1536.61,1538.19,1538.98,1539.77,
1540.56,1542.14,1542.94,1543.73,1544.53,1546.12,1546.92,,1547.72,
1548.51,1550.12,1550.92,1551.72,1552.52,1554.13,1554.94,
1555.75,1556.55,1558.17,1558.98,1559.79,1560.61}

Wavelength identifier


4.6  Parameter Descriptions

This section provides a description of parameter types defined for the TL1 messages used in the ONS 15454 SDH. Individual parameters are listed within each command description in Chapter 3, "TL1 Command Descriptions".

4.6.1  ATAG Description

The autonomous message tag (ATAG) is used for message sequencing. There are four streams of autonomous messages and each stream corresponds to a sequence. The sequence numbers increment by one for each autonomous message within that stream. The format and range of ATAG differs for each stream. The four streams are:

1. Alarmed events:

These include REPT ALM and REPT EVT (except REPT EVT SESSION) messages as well as the REPT SW autonomous message.

ATAG Format: x.y
where
x - sequence number of this alarmed event. This is an integer in the range of 0-9999.
y - sequence number of the previous alarmed event which is related to this alarmed event. This is an integer in the range of 0-9999.

If there is no such previous related event, then y will be the same as x. For example, the first time an alarm is raised you will receive the autonomous message:

TID-000 1998-06-20 14:30:00
* 1346.1346 REPT ALM E1
"FAC-1-1:MN,LOS,NSA,,,,:\"Loss Of Signal\",E1-14"
;

When this alarmed event/condition is cleared, you will receive the autonomous message:

TID-000 1998-06-20 14:31:00
A 1349.1346 REPT ALM E1
"FAC-1-1:CL,LOS,NSA,,,,:\"Loss Of Signal\",E1-14"
;

2. Database change messages:

The REPT DBCHG message falls into this category.

ATAG Format: x
where:
x - sequence number of the database change update message. This is an integer in the range of 0-9999. For example:

TID-000 1998-06-20 14:30:00
A 96 REPT DBCHG
"TIME=18-01-05,DATE=1970-01-01,SOURCE=2,USERID=CISCO15,
DBCHGSEQ=96:ENT-EQPT:SLOT-3"
;


Note The ATAG is the same as the DBCHGSEQ field in the REPT DBCHG output.


3. PM Reports:

The REPT PM messages fall into this category.

ATAG format: x
where:
x - sequence number of the PM report. This is an integer in the range of 0-9999. For example:

TID-000 1998-06-20 14:30:00
A5 REPT PM E1
"FAC-3-1:CVL,10,PRTL,NEND,BTH,15-MIN,05-25,14-46"
;

This sequence number is global across all existing PM schedules.

4. Autonomous messages specific to a TL1 session. These messages are usually related to the security aspect of the TL1 session. Only the autonomous messages REPT EVT SESSION and CAN fall under this category. This is an integer in the range 0-9999.

For example:

TID-000 1998-06-20 14:30:00
A 1 CANC
"User"
;

4.6.2  CTAG Description

The correlation tag (CTAG) is included in each command by the user and is repeated by the
NE in the response to allow the user to associate the command and response messages. The valid values for a CTAG are strings of up to 6 characters comprised of identifiers (alphanumeric, beginning with a letter) or non-zero decimal numbers (a string of decimal digits with an optional non-trailing ".").

A zero in the response field is valid when indicating an error; for example, issuing a semi-colon by itself results in:

TID-000 1998-06-20 14:30:00
M 0 DENY IISP
/* Input, Garbage */
;

4.6.3  TID Description

The TID is the name of the NE where the command is addressed. TID is the Telcordia name for the system.

4.6.4  Parameter Notes

1. If a parameter is set to a value that is inconsistent with something already in the database, and that value is not changed to a consistent value then the command will be denied.

2. If a parameter is set to a value that is consistent with what is already in the database, but another parameter in the same command is incompatible, then the command will be denied.

3. The correct way to issue a command where parameters may be in conflict is to:

a. First issue that command and change all relevant parameters to compatible values,

b. Then issue the command again to change the target values.

For example, OC-N is syncmsg=y, to change SDH to y, ED-OCN needs to be called to set syncmsg=N, then called again to set SDH=y.

4. The attribute defaults have also been presented under RTRV commands, and they can be retrieved only if the RTRV commands follow the card/entity original provision.

5. The default for an optional field of an ED command is either the provisioned default value or the last provisioned value in the previous ED command.