Cisco ONS 15454 SDH TL1 Command Guide, Release 5.0
Chapter 6, TL1 Errors
Downloads: This chapterpdf (PDF - 223.0KB) The complete bookPDF (PDF - 9.12MB) | Feedback

TL1 Errors

Table Of Contents

TL1 Errors

6.1  Errors

6.2  Echo


TL1 Errors


This chapter provides TL1 error information supported by the Cisco ONS 15454 SDH. For alarm information, Refer to the Cisco ONS 15454 SDH Procedure Guide, Cisco ONS 15454 SDH Troubleshooting Guide and Cisco ONS 15454 SDH Reference Manual.

6.1  Errors

Errors may be generated by any command or command response message. You can find errors listed by error code in Table 6-1. The format of an error message is as follows:

SID DATE TIME
M CTAG DENY
<ERRCDE>
/* <ERRMSG> */
;

Table 6-1 TL1 Errors 

Error Code
Error messages

ENEQ

Communication Failed

Control Not Provisioned

Cost Not Found

Equipment Is Deleted

Equipment Not Found

Equipment Not Present

Equipment Not Provisioned

IP Address Not Found

IP Mask Not Found

Next Hop Not Found

No standby present

No standby provisioned

Not Equipped

Sensor IF Is Not Found

IBEX

Extra Datablock

Extra parameters

 

ICNV

Equipment In Use

Invalid Command

PM Type Not Supported

 

IDMS

Data Missing

Loopback Type Missing

Missing Internal Data

 

IDNC

Invalid Data

Invalid PST Value

Invalid SST Value

 

IDNV

AISONLPBK Not Supported

AMPLMODE Not Supported

CALOPWR Not Supported

CALTILT Not Supported

CHPOWER Not Supported

Cannot Access DCC

DCC is in use

Description Too Long

Edit Line Code Failed

Interval Out Of Range

Invalid Alarm Message

Invalid Data Rate

Invalid Data Rate

Invalid Drop Path

Invalid Equipment Type

Invalid Interval

Invalid Log Name

Invalid MONLEV Value

Invalid MONTYPE Value

Invalid Mac Address

Invalid Next Hop

Invalid Notification Code

Invalid PM Interval

Invalid PPM Port

Invalid Protid

Invalid Reference

Invalid Regen Group AID

Invalid Report Interval

Invalid Start Time

Invalid TAP Number

Invalid TXCOUNT Or RXCOUNT

Invalid TXCOUNT Or RXCOUNT

Invalid TXCOUNT

Invalid Time Offset

Invalid Trace Level

Invalid User Name

Invalid VCAT Group Name

Keyword All Not Allowed

Line Code Not Supported

OSRI Not Supported

PPM Does Not Exist

Rate Capacity Exceeded

SDCC is in use

TMPER Type Not Supported

Tap Out Of Range

Trace Level Required

VOA Not Supported

VOA Out Of Range

Value Or Threshold Read Only

IDRG

Difference Value Range Error

Invalid DURAL Value

Invalid MXINV Value

Invalid PAGE Value

Invalid PCND Value

Invalid PINT Value

Invalid PJMON Value

Invalid POLD Value

Invalid TMOUT Value

Invalid Threshold Value

Invalid UOUT Value

Invalid Watermark Value

PJMON Out Of Range

IIAC

AID PARSE ERROR

ALL AID Not Allowed

Bad Ring Id

DS1 Out of Range

FAC parse failed

Incorrect Card Type

Input, Invalid Access

Invalid AID

Invalid DRI Node Type

Invalid DRI Topology

Invalid DS1 AID

Invalid FROM= AID

Invalid Month Or Day

Invalid Node Side

Invalid NodeId

Invalid PJMON Value

Invalid Protect AID

Invalid RTO AID

Invalid Reference

Invalid RingId

Invalid Source AID

Invalid TAPI

Invalid TO= AID

Invalid TPORT AID

Invalid Time

Invalid VCG Member Number

Invalid Year

Invalid fac-n-m input

Loopback type mismatch

Multiple AIDs Not Allowed

IICM

Input, Invalid Command

Input, Invalid MOD1

Input, Invalid MOD2

Input, Invalid MOD2

Input, Invalid VERB

 

IICT

Invalid Correlation Tag

 

IIDT

CMDMDE Must Be FRCD

Duplicate Schedule

FRCD mode not supported

FTTD URL Missing

File Name Missing In URL

Flash Manager Not Active

Hostname Missing In URL

IOS Config File Too Big

Invalid Data Parameter

Invalid East work Port

Invalid FTTD Host

Invalid NSAP Character

Invalid NSAP Length

Invalid Phase Number

Invalid Port In URL

Invalid Revertive Time

Invalid State Value

Invalid West work Port

Memory Out Of Range

Missing/Invalid Source

Password Missing In URL

Port Missing In URL

SRC Required For RFR Type

Unsupported Locn Value

Username Missing In URL

ftp:// Missing In FTP URL

IIFM

Invalid Data Format

Invalid Password

Invalid User ID

 

IISP

Input, Garbage

 

INUP

General Block Unsupported

 

IPEX

Duplicate N/V field

 

IPMS

Invalid syntax

 

IPNC

Description Too Long

Invalid Encapsulation Type

Invalid Flow Control Value

Invalid Maximum Frame Size

Invalid Parameter

Invalid Trans Value

Parameter Not Valid

Parameters Not Compatible

 

IPNV

Bad Parameter

Bad Reference

Empty parameter

INVALID SAMPLE TYPE

Internal-Ip Lookup Failed

Invalid BITS Framing

Invalid BITS-OUT Rate

Invalid Clock Source

Invalid Condition Type

Invalid DRITYPE

Invalid IIOP Port number

Invalid IP Address

Invalid IP Mask

Invalid MONLEV Value

Invalid PM register

Invalid Parameter

Invalid Report Interval

Invalid SNTP Host Address

Invalid Start Time

Invalid Switch Type

Invalid Threshold Value

Invalid why parameter

PM Not Supported

Parameter Not Valid

NO

No error

 

PICC

AID Required

Can't login

Logout failed

Password Recently Changed

Unexpected Default Case

Unknown User

User Already Exists

User Not Authorized

User Password Required

 

PIMA

Memory Out Of Range

 

PIUC

Unauthorized

User Is Not Superuser

User Not Logged In

 

RALB

Requested DCC In Use

 

RRNG

Invalid Slot Number

 

RTBY

Connection In Service

TAP Already In Use

TAP Number In Use

 

RTEN

Cannot Set Access Mode

Invalid Access Mode

Invalid TAP AID

Invalid TAP Mode

Invalid TAP Number

Requested Tap Busy

TAP Not Found

 

SAAL

Already Allowed

 

SADC

GNE: ENE is down

TAP Not Connected

 

SAIN

Already Inhibited

 

SAIS

Port Already In Service

 

SAOP

Control Already Operated

Control Already Released

 

SAOS

Port Already Out Of Service

 

SCAT

Connection is tapped

Test Access Busy

 

SDBE

AID Parser Failed

Bad Parameter

Cannot Access Alarms

Cannot Access Conditions

Cannot Access Controls

Cannot Access Date/Time

Cannot Access Equipment

Cannot Access Facility

Cannot Access Interface

Cannot Access Node ID

Cannot Access Node Name

Cannot Access Object

Cannot Access Orderwire

Cannot Access SNTP Host

Cannot Access Timezone

Cannot Configure SYNC

Cannot Set Date

Cannot Set Node Name

Cannot Set Timezone

DLT prg Failed

Equipment Not Found

Facility Does Not Exist

Facility Is Not Provisioned

File Transfer In Progress

IP Configuration Failed

Incorrect Facility Type

Internal Access Failed

Internal Data Base Error

Internal Database Error

Invalid Command

Invalid DCC

Invalid Mondat Format

Invalid Montm Format

Invalid Protection Group

Invalid Time Period

Location Value Invalid

Loopback Is Invalid

Loopback Port In Service

No such interface

Not a Sonet interface

Object Not Provisioned

Object Not Supported

Path Width Not Supported

Wrong Facility Type

Wrong Interface Type

bind failed for sonet gen

getRefSources failed

SDLD

Duplex Unit Locked

 

SDNA

Active TCC Not Ready

Standby TCC Not Ready

 

SDNR

Data Not Ready

 

SNCN

Bad Quality

Command Not Implemented

Invalid Clock Source

 

SNPR

Cannot Get Role Of Port

Get Port Role Failed

 

SNVS

CCAT Cross Connect Exists

Cannot END an AUTO roll

Cross Connect Exists

Invalid AINS Soak Time

Invalid Admin State

Invalid Clock Source

Invalid Equipment State

Loopback Not In Progress

No Switch In Progress

No loopback in progress

No valid roll signal

Protection Unit Active

VCG Already Created

Working Unit Already Active

SOSE

Unrecognized Message Type

 

SPLD

Cannot Delete Equipment

Equipment In Use

FTP Task Is Busy

Facility Is Busy

Protection Unit Locked

 

SRAC

Invalid Connection Type

 

SROF

1WAYMON not supported

APC System Is Busy

All DCCs In Use

CKTID Does Not Match

Cannot Access Alarm Log

Cannot Access DCC

Cannot Access Facility

Cannot Access PM Mode

Cannot Access TAP

Cannot Add Equipment

Cannot Add Equipment

Cannot Configure SYNC

Cannot Create TAP

Cannot Delete Last Drop

Cannot Delete VCAT Group

Cannot Edit Ethernet IP

Cannot Perform ACO

Cannot Provision Equipment

Cannot Set ALS Mode

Cannot Set NodeId

Cannot Set Payload Type

Cannot Set RingId

Cannot Set Wave Length

Cannot set loopback

Command Not Supported

Connection In Loopback

Connection In Roll

Connection type error

Connection type error

Could Not Delete Protection

DCC Does Not Exist

DCC In UseDCC Not In Use

DWRAP Not Enabled

Database Is Busy

Element Not Found

Element not available

Facility Not Protected

Fail to add RTO

Flash Is Busy

Get IOR Failed

SROF (continued)

Internal Database Error

Internal Exercise Failure

Invalid AID

Invalid BLSR DRI Drop

Invalid Drop Path

Invalid Path

Invalid Protection Group

Invalid RMODE

Invalid SYNC entity

Invalid Subnet Mask

Invalid Username/Password

Is Not 1+1 Element Type

MIC Cards Cannot Be Reset

Maximum User Limit Reached

No Path To Regulate

No Start-Up IOS Config

Operation Not Supported

Path Already In Use

Path Specified Is Not Valid

Path Used For Test Access

Pool Does Not Exist

Pool not available

Port Type Mismatch

Port Type Not Provisioned

Protect Port Active

Provisioning Rules Failed

Requested Operation Failed

Requested Tap Busy

Ring Reversion Failed

SDBER Out Of Range

SDCC creation failed

SFBER Out Of Range

Set PRG Name Failed

Software Activation Failed

Software Download Failed

Software Error

Software Reversion Failed

Span Reversion Failed

TAP connected

Tap Not Provisioned

Test Access Active

Trace Mode Not Supported

Trap Table Full

Unable to cancel roll

Unknown Internal Error

VCG Does Not Exist

XC Card Not Present

SRQN

DCC not enabled

Invalid Request

SDH Not Allowed With DCC

SDH Not Allowed

 

SRTN

TAP Not Found

 

SSRD

Switch Request Denied

 

SSRE

Memory Resources Exceeded

Memory resource denial

 

SWLD

Working Unit Locked

 

6.2  Echo

In order to improve telnet functionality for automated systems, the echo function has been turned off. This change is transparent to users running standard UNIX-compliant telnet clients; however, PC users may need to change their client setup to enable "local echo." This is normally accomplished by a pull-down menu or a preference attribute.

To test the local echo on your PC client, use the RTRV-HDR command. If you receive a response but no data, set local echo ON. Cisco recommends that you close any windows containing sensitive information after exiting a TL1 session.