Cisco ONS 15454 SDH Procedure Guide, Release 5.0
Chapter 2, Install Cards and Fiber-Optic Cable
Downloads: This chapterpdf (PDF - 688.0KB) The complete bookPDF (PDF - 26.98MB) | Feedback

Install Cards and Fiber-Optic Cable

Table Of Contents

Install Cards and Fiber-Optic Cable

Before You Begin

NTP-D15 Install the Common Control Cards

NTP-D16 Install the STM-N Cards

NTP-D17 Install the Electrical Cards

NTP-D18 Install Ethernet Cards and Connectors

NTP-D286 Install the FC_MR-4 Cards

NTP-D19 Install Fiber-Optic Cables on STM-N Cards

NTP-D245 Route Fiber-Optic Cables

NTP-D227 Remove and Replace a Card

NTP-D20 Replace the Front Door


Install Cards and Fiber-Optic Cable


This chapter explains how to install the Cisco ONS 15454 SDH cards and fiber-optic cable (fiber).

Before You Begin

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. D15 Install the Common Control Cards—Complete this procedure before installing any other cards.

2. D16 Install the STM-N Cards—Complete this procedure as needed.

3. D17 Install the Electrical Cards—Complete this procedure as needed.

4. D18 Install Ethernet Cards and Connectors—Complete this procedure as needed.

5. D286 Install the FC_MR-4 Cards—Complete this procedure as needed.

6. D19 Install Fiber-Optic Cables on STM-N Cards—Complete this procedure to install fiber on the optical cards, small form-factor pluggables (SFPs) and Ethernet Gigabit Interface Converters (GBICs), and route the fiber through through the bottom of the shelf.

7. D245 Route Fiber-Optic Cables—Complete as needed.

8. D227 Remove and Replace a Card—Complete this procedure as needed to remove and replace a card, including deleting the card from Cisco Transport Controller (CTC) and changing an optical card without losing the card's provisioning.

9. D20 Replace the Front Door—If the front door was removed, complete this procedure to replace the front door and ground strap after installing cards and fiber.


Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030



Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Statement 1029



Caution Unused card slots should be filled with a blank faceplate (Cisco P/N 15454E-BLANK). The blank faceplate ensures proper airflow when operating the ONS 15454 SDH without the front door attached, although Cisco recommends that the front door remain attached.

NTP-D15 Install the Common Control Cards

Purpose

This procedure describes how to install the common control cards.

Tools/Equipment

Redundant TCC2/TCC2P cards

Redundant XC10G, XC-VXL-10G, or XC-VXL-2.5G (cross-connect) cards

AIC-I card (optional)

Prerequisite Procedures

NTP-D13 Perform the Shelf Installation Acceptance Test, page 1-18

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Provisioning or higher



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Caution Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside to edge of the shelf assembly.


Note If protective clips are installed on the backplane connectors of the cards, remove the clips before installing the cards.



Note If you install a card incorrectly, the FAIL LED flashes continuously.



Step 1 If you plan to install XC-VXL-2.5G cards, review Table 2-1 to determine card/slot compatibility. If you plan to install XC10G or XC-VXL-10G cards, review Table 2-2 to determine card/slot compatibility.

Step 2 Complete the "DLP-D332 Install the TCC2/TCC2P Cards" task on page 20-24.

Figure 2-1 shows card installation.

Figure 2-1 Installing Cards in the ONS 15454 SDH

Step 3 Complete the "DLP-D333 Install the XC10G, XC-VXL-10G, or XC-VXL-2.5G Cards" task on page 20-27.


Note If you install the wrong card in a slot, see the "D227 Remove and Replace a Card" procedure.


Step 4 Complete the "DLP-D334 Install the Alarm Interface Controller-International Card" task on page 20-29, if necessary.

In Table 2-1, X indicates that a card is supported in the slot.

Table 2-1 ONS 15454 SDH Card and Slot Compatibility for the XC-VXL-2.5G Cards 

Slot
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Type
MS 1
MS 1
MS 1
MS 1
HS 2
HS 2
TCC2/ TCC2P
XC 3
AIC-I
XC 3
TCC2/ TCC2P
HS 2
HS 2
MS 1
MS 1
MS 1
MS 1

TCC2/TCC2P

           

X

     

X

           

XC-VXL-2.5G

             

X

 

X

             

AIC-I

               

X

               

DS3i-N-12

X

X

X

X

X

             

X

X

X

X

X

E1N-14

X

X

X

X

X

             

X

X

X

X

X

E1-42

X

X

X

X

                 

X

X

X

X

E3-12

X

X

X

X

X

             

X

X

X

X

X

STM1E-12

X

X

X

X

                 

X

X

X

X

E100T-G

X

X

X

X

X

X

         

X

X

X

X

X

X

E1000-2-G

X

X

X

X

X

X

         

X

X

X

X

X

X

G1000-4

X

X

X

X

X

X

         

X

X

X

X

X

X

G1K-4

X

X

X

X

X

X

         

X

X

X

X

X

X

ML100-12

X

X

X

X

X

X

         

X

X

X

X

X

X

ML1000-2

X

X

X

X

X

X

         

X

X

X

X

X

X

OC3 IR 4/STM1 SH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC3IR/STM1 SH 1310-8

X

X

X

X

Requires XC10G or XC-VXL-10G cards.

   

X

X

X

X

OC12 IR/STM4 SH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1310-4

X

X

X

X

Requires XC10G or XC-VXL-10G cards.

   

X

X

X

X

OC12 LR/STM4 LH 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 IR/STM16 SH AS 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 LR/STM16 LH AS 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 ELR/STM16 EH 100 GHz

       

X

X

         

X

X

       

OC192 SR/STM64 IO 1310

Not supported with XC-VXL-2.5G cards. Requires XC10G or XC-VXL-10G cards.

OC192 IR/STM64 SH 1550

Not supported with XC-VXL-2.5G cards. Requires XC10G or XC-VXL-10G cards.

OC192 LR/STM64 LH 1550

Not supported with XC-VXL-2.5G cards. Requires XC10G or XC-VXL-10G cards.

OC192 LR/STM64 LH ITU 15xx.xx

Not supported with XC-VXL-2.5G cards. Requires XC10G or XC-VXL-10G cards.

FC_MR-4

X

X

X

X

X

X

         

X

X

X

X

X

X

Slot
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

1 MS identifies slots 1 to 4 and 14 to 17 ("multispeed" slot).

2 HS identifies slots 5, 6, 12, and 13 ("high-speed" slot).

3 The term XC is used generically to mean "cross-connect."


In Table 2-2, X indicates that a card is supported in the slot.

Table 2-2 Slot Compatibility for the XC10G or XC-VXL-10G Card 

Slot
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Type
MS 1
MS 1
MS 1
MS 1
HS 2
HS 2
TCC2/TCC2P
XCs
AIC-I
XCs
TCC2/TCC2P
HS 2
HS 2
MS 1
MS 1
MS 1
MS 1

TCC2/TCC2P

           

X

     

X

           

XC10G

             

X

 

X

             

XC-VXL-10G

             

X

 

X

             

AIC-I

               

X

               

DS3i-N-12

X

X

X

X

X

             

X

X

X

X

X

E1N-14

X

X

X

X

X

             

X

X

X

X

X

E1-42

X

X

X

X

                 

X

X

X

X

E3-12

X

X

X

X

X

             

X

X

X

X

X

STM1E-12

X

X

X

X

                 

X

X

X

X

E100T-G

X

X

X

X

X

X

         

X

X

X

X

X

X

E1000-2-G

X

X

X

X

X

X

         

X

X

X

X

X

X

G1000-4

X

X

X

X

X

X

         

X

X

X

X

X

X

G1K-4

X

X

X

X

X

X

         

X

X

X

X

X

X

ML100-12

X

X

X

X

X

X

         

X

X

X

X

X

X

ML1000-2

X

X

X

X

X

X

         

X

X

X

X

X

X

OC3 IR 4/STM1 SH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC3IR/STM1SH 1310-8

X

X

X

X

                 

X

X

X

X

OC12 IR/STM4 SH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC12 LR/STM4 LH 1310-4

X

X

X

X

                 

X

X

X

X

OC12 LR/STM4 LH 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 IR/STM16 SH AS 1310

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 LR/STM16 LH AS 1550

X

X

X

X

X

X

         

X

X

X

X

X

X

OC48 ELR/STM16 EH 100 GHz

X

X

X

X

X

X

         

X

X

X

X

X

X

OC192 SR/STM64 IO 1310

       

X

X

         

X

X

       

OC192 IR/STM64 SH 1550

       

X

X

         

X

X

       

OC192 LR/STM64 LH 1550

       

X

X

         

X

X

       

OC192 LR/STM64 LH ITU 15xx.xx

       

X

X

         

X

X

       

FC_MR-4

X

X

X

X

X

X

         

X

X

X

X

X

X

1 MS identifies slots 1 to 4 and 14 to 17 ("multispeed" slot).

2 HS identifies slots 5, 6, 12, and 13 ("high-speed" slot).


Step 5 Continue with the following procedures, as needed:

D16 Install the STM-N Cards

D17 Install the Electrical Cards

D18 Install Ethernet Cards and Connectors

D286 Install the FC_MR-4 Cards

Stop. You have completed this procedure.


NTP-D16 Install the STM-N Cards

Purpose

This procedure installs the optical cards (STM-1, STM1-8, STM-4, STM4-4, STM-16, and STM-64). Install according to site plan, if available.

Tools/Equipment

STM-1, STM-4, STM-16, and STM-64 cards (as applicable)

Prerequisite Procedures

D15 Install the Common Control Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057



Warning Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products. Statement 291



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056



Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057



Warning On all optical cards except the OC192 LR/STM64 LH 1550 card, the laser is on even when the optical port is not in service. On the OC192 LR/STM64 LH 1550 card, the laser is active when the card is booted and the safety key is in the on position (labeled 1). The laser is off when the safety key is off (labeled 0).



Caution Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.


Note To simplify subnetwork connection protection (SNCP) to multiplex section-shared protection ring (MS-SPRing) conversion and node addition, install optical cards according to a high-speed east (Slots 12 and 13) and west (Slots 5 and 6) configuration. This configuration is not mandatory.



Note If you install a card incorrectly, the FAIL LED flashes continuously.



Note During the boot proces, a Locked-enabled,disabled STM-N port will output AIS-L to any Unlocked-enabled far-end receivers. See the Cisco ONS 15454 SDH Troubleshooting Guide for further information about the AIS-L condition.



Step 1 If you installed XC-VXL-2.5G cards, review Table 2-1 to determine card/slot compatibility. If you installed XC10 or XC-VXL-10G cards, review Table 2-2 to determine card/slot compatibility.

Install higher-capacity cards first; for example, install an STM-64 card before installing an STM-12 card. Let each card completely boot before installing the next card.

Step 2 Open the card latches/ejectors.


Warning Before installing an OC192 LR/STM64 LH 1550 card, make sure the safety key on the faceplate is in off position (labeled 0). When in the on position (labeled 1), the laser is activated.


Step 3 Use the latches/ejectors to firmly slide the optical card along the guide rails until the card plugs into the receptacle at the back of the slot.

Step 4 Verify that the card is inserted correctly and close the latches/ejectors on the card.


Note It is possible to close the latches/ejectors when the card is not completely plugged into the backplane. Ensure that you cannot insert the card any further.



Note If you install the wrong card in a slot, complete the "D227 Remove and Replace a Card" procedure.


Step 5 Verify the LED activity:

The red FAIL LED turns on for 20 to 30 seconds.

The red FAIL LED blinks for 35 to 45 seconds.

All LEDs blink once and turn off for 5 to 10 seconds.

The ACT or ACT/STBY LED turns on. The signal fail (SF) LED can persist until all card ports connect to their far-end counterparts and a signal is present.


Note The booting STM-N card will send AIS-L to the far-end receiver as long as it is Locked-enabled,disabled.


Step 6 If the card does not boot up properly, or the LED activity does not mimic Step 5, check the following:

When a physical card type does not match the type of card provisioned for that slot in CTC, the card might not boot. If an optical card does not boot, open CTC and verify that the slot is not provisioned for a different card type before assuming the card is faulty.

If the red FAIL LED does not turn on, check the power.

If you insert a card into a slot provisioned for a different card, all LEDS turn off.

If the red FAIL LED is illuminated continuously or the LEDs behave erratically, the card is not installed properly. Remove the card and repeat Steps 2 to 5.

Step 7 Continue with the "D19 Install Fiber-Optic Cables on STM-N Cards" procedure.

Stop. You have completed this procedure.


NTP-D17 Install the Electrical Cards

Purpose

This procedure installs the electrical cards (DS3i-N-12, E1N-14, E1-42, E3-12, and STM1E-12).

Tools/Equipment

Electrical cards

Prerequisite Procedures

NTP-D220 Install the Power and Signal FMECs, page 1-7

D15 Install the Common Control Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Note The E3-12 card can be deployed in a central office or a carrier´s exchange.



Note Install higher-capacity cards first; for example, install an E3-12 card before installing an E1-14 card. Let each card boot completely before installing the next card.



Note Cisco recommends installing STM-N, TXP, and MXP cards before you install electrical cards, as applicable.



Step 1 If you installed XC-VXL-2.5G cards, review Table 2-1 to determine card/slot compatibility. If you installed XC10 or XC-VXL-10G cards, review Table 2-2 to determine card/slot compatibility.

Step 2 Open the card latches/ejectors.

Step 3 Use the latches/ejectors to firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot.


Note If you install the wrong card in a slot, complete the "D227 Remove and Replace a Card" procedure.


Step 4 Verify that the card is inserted correctly and close the latches/ejectors on the card.


Note It is possible to close the latches/ejectors when the card is not completely plugged into the backplane. Ensure that you cannot insert the card any further.


Step 5 Verify the LED activity:

The red FAIL LED turns on for 10 to 15 seconds.

If the red FAIL LED does not turn on, check the power.

The red FAIL LED blinks for 30 to 40 seconds.

All LEDs blink once and turn off for 1 to 5 seconds.

The ACT or ACT/STBY LED turns on. The SF LED can persist until all card ports connect to their far end counterparts and a signal is present.


Note If you insert a card into a slot provisioned for a different card, all LEDs turn off.



Note If the red FAIL LED is on continuously or the LEDs behave erratically, the card is not installed properly. Remove the card and repeat Steps 2 to 5.


Step 6 Continue with the "D18 Install Ethernet Cards and Connectors" procedure if necessary.

Stop. You have completed this procedure.


NTP-D18 Install Ethernet Cards and Connectors

Purpose

This procedure installs the Ethernet cards (E100T-G, E1000-2-G, G1000-4, G1K4, ML100T-12, and ML1000-2).

Tools/Equipment

Ethernet cards

Prerequisite Procedures

D15 Install the Common Control Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Warning Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products. Statement 291



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056



Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057



Caution Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.


Note Cisco recommends installing TXP, MXP, STM-N, and electrical cards before you install Ethernet cards, as applicable.



Step 1 If you installed XC-VXL-2.5G cards review Table 2-1 to determine card/slot compatibility. If you installed XC10 or XC-VXL-10G cards, review Table 2-2 to determine card/slot compatibility.

Step 2 Complete the "DLP-D39 Install Ethernet Cards" task on page 17-29. Allow each card to boot completely before installing the next card.

Step 3 Complete the "DLP-D335 Install GBIC or SFP Connectors" task on page 20-30 if you are using E1000-2-G, G1000-4, G1K-4, or ML1000-2 cards.


Note If you need to remove a GBIC or SFP, complete the "DLP-D336 Remove GBIC or SFP Connectors" task on page 20-33.


Step 4 Continue with "D286 Install the FC_MR-4 Cards" procedure if necessary.

Stop. You have completed this procedure.


NTP-D286 Install the FC_MR-4 Cards

Purpose

This procedure installs the FC_MR-4 card, also known as the Fibre Channel card.

Tools/Equipment

FC_MR-4 card(s)

Prerequisite Procedures

D15 Install the Common Control Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Warning Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products. Statement 291



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056



Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057



Caution Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.


Note If protective clips are installed on the backplane connectors of the cards, remove the clips before installing the cards.



Warning High-performance devices on this card can get hot during operation. To remove the card, hold it by the faceplate and bottom edge. Allow the card to cool before touching any other part of it or before placing it in an antistatic bag. Statement 201



Step 1 If you installed XC-VXL-2.5G cards review Table 2-1 to determine card/slot compatibility. If you installed XC10G or XC-VXL-10G cards, review Table 2-2 to determine card/slot compatibility.

Step 2 Open the card latches/ejectors.

Step 3 Use the latches/ejectors to firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot.

Step 4 Verify that the card is inserted correctly and close the latches/ejectors on the card.


Note It is possible to close the latches/ejectors when the card is not completely plugged into the backplane. Ensure that you cannot insert the card any further.



Note If you install the wrong card in a slot, complete the "D227 Remove and Replace a Card" procedure and install the correct card.


Step 5 Verify the LED activity:

The red FAIL LED turns on for 20 to 30 seconds. The ACT LED is amber for 3 to 5 seconds.

The red FAIL LED blinks for up to 2 minutes.

The FAIL and ACT LEDs blink once and turn off for 1 to 5 seconds.

The ACT LED illuminates green.


Note If the red FAIL LED does not turn on, check the power.



Note If you insert a card into a slot provisioned for a different card, all LEDs turn off.


Step 6 Complete the "DLP-D335 Install GBIC or SFP Connectors" task on page 20-30 to install GBICs on the FC_MR-4 card.


Note If you need to remove a GBIC or SFP, complete the "DLP-D336 Remove GBIC or SFP Connectors" task on page 20-33.


Step 7 Continue with the "D19 Install Fiber-Optic Cables on STM-N Cards" procedure.

Stop. You have completed this procedure.


NTP-D19 Install Fiber-Optic Cables on STM-N Cards

Purpose

This procedure describes how to install fiber-optic cables on optical cards.

Tools/Equipment

Fiber-optic cables

Fiber boot

Prerequisite Procedures

D16 Install the STM-N Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products. Statement 291



Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056



Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057



Warning On all STM-N cards except the OC192 LR/STM64 LH 1550 card, the laser is on even when the optical port is not in service. If an OC192 LR/STM64 LH 1550 card has a safety key, the laser is active when the card is booted and the safety key is in the on position (labeled 1). The laser is off when the safety key is off (labeled 0).



Warning Laser radiation presents an invisible hazard, so personnel should avoid exposure to the laser beam. Personnel must be qualified in laser safety procedures and must use proper eye protection before working on this equipment. Statement 300



Caution Do not use fiber loopbacks with the STM64 LH 1550 or STM64 LH ITU 15xx.xx card unless you are using a 20-dB attentuator. Never connect a direct fiber loopback. Using fiber loopbacks causes irreparable damage to the STM64 LH 1550 or STM64 LH ITU 15xx.xx card.


Caution Do not use fiber loopbacks with the STM64 SH 1550 card unless you are using a 5-dB attentuator. Never connect a direct, unattenuated fiber loopback. Using unattenuated fiber loopbacks causes irreparable damage to the STM64 SH 1550 card.


Caution Always use the supplied ESD wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.


Note You can install the fiber immediately after installing the cards, or wait until you are ready to turn up the network. See Chapter 5, "Turn Up Network."



Step 1 Test the optical receive levels for the cards installed and attenuate accordingly. Table 2-3 provides the minimum and maximum levels.

Table 2-3 Optical Transmit and Receive Levels 

Card
Transmit
Receive
Minimum
Maximum
Minimum
Maximum

OC3 IR 4/STM1 SH 1310

-15 dBm

-8 dBm

-28 dBm

-8 dBm

OC3IR/STM1SH 1310-8

-15 dBm

-8 dBm

-28 dBm

-8 dBm

OC12 IR/STM4 SH 1310

-15 dBm

-8 dBm

-28 dBm

-8 dBm

OC12 LR/STM4 LH 1310

-3 dBm

+2 dBm

-28 dBm

-8 dBm

OC12 LR/STM4 LH 1550

-3 dBm

+2 dBm

-28 dBm

-8 dBm

OC12 IR/STM4 SH 1310-4

-15 dBm

-8 dBm

-30 dBm

-8 dBm

OC48 IR/STM16 SH AS 1310

-5 dBm

0 dBm

-18 dBm

0 dBm

OC48 LR/STM16 LH AS 1550

-2 dBm

+3 dBm

-28 dBm

-8 dBm

OC48 ELR/STM16 EH 100 GHz

-2 dBm

0 dBm

-27 dBm at 1E-12 BER

-9 dBm

OC192 SR/STM64 IO 1310

-6 dBm

-1 dBm

-11 dBm

-1 dBm

OC192 IR/STM64 SH 1550

-1 dBm

+2 dBm

-14 dBm

-1 dBm

OC192 LR/STM64 LH 1550

+7 dBm

+10 dBm

-19 dBm

-10 dBm

OC192 LR/STM64 LH ITU 15xx.xx

+3 dBm

+6 dBm

-22 dBm

-9 dBm


Step 2 Inspect and clean all fiber connectors thoroughly. See the "NTP-D112 Clean Fiber Connectors" procedure on page 15-13 for instructions. Dust particles can degrade performance. Put caps on any fiber connectors that are not used.

Step 3 As needed, complete the "DLP-D42 Install Fiber-Optic Cables on an LGX Interface" task on page 17-32.


Note To install fiber-optic cables on Ethernet cards or FC_MR-4 cards, see the "DLP-D335 Install GBIC or SFP Connectors" task on page 20-30.


Step 4 As needed, complete the "DLP-D337 Install Fiber-Optic Cables for SNCP Configurations" task on page 20-34.

Step 5 As needed, complete the "DLP-D338 Install Fiber-Optic Cables for MS-SPRing Configurations" task on page 20-37.

Step 6 As needed, complete the "DLP-D45 Install the Fiber Boot" task on page 17-34.

Step 7 Continue with the "D245 Route Fiber-Optic Cables" procedure.

Stop. You have completed this procedure.


NTP-D245 Route Fiber-Optic Cables

Purpose

This procedure routes fiber-optic cables.

Tools/Equipment

None

Prerequisite Procedures

D19 Install Fiber-Optic Cables on STM-N Cards

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Open the fold-down front door on the cable-management tray (Figure 2-2).

Figure 2-2 Fold-Down Front Door of the Cable-Management Tray

Step 2 Route the fiber cable on the card faceplate through the fiber clip on the faceplate (Figure 2-3) . Fiber clips are factory-attached to the faceplate of the STM-N cards and some DWDM cards (32MUX-O, 32DMX-O, OSCM, OPT-PRE, and OPT-BST).


Note GBICs and SFPs do not have fiber clips; therefore, if you are routing optical cable from an FC_MR-4, E1000-2-G, G1000-4, G1K-4, or ML1000-2 card, skip to Step 3.


Figure 2-3 Routing Fiber-Optic Cables on the Optical-Card Faceplate

Step 3 Route the fiber cables into the cable-management tray (Figure 2-3).

Step 4 Route the fiber cables out either side of the cable-management tray through the cutouts on each side of the shelf assembly. Use the reversible fiber guides to route cables out the desired side.

Step 5 Close the fold-down front door when all fiber cables in the front compartment are properly routed.

Stop. You have completed this procedure.


NTP-D227 Remove and Replace a Card

Purpose

This procedure removes and replaces cards in the ONS 15454 SDH shelf.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 17-47

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

Provisioning or higher



Step 1 If you are not logged into CTC and you need to remove a card, remove the card as described in Step 3. When you log into CTC, troubleshoot the mismatched equipment alarm (MEA) with the Cisco ONS 15454 SDH Troubleshooting Guide.

Step 2 If you are logged into CTC, complete one of the following:

Complete the "DLP-D191 Delete a Card" task on page 18-34 and continue with Step 3.

Complete the "DLP-D247 Change an STM-N Card" task on page 19-29 to delete a card and replace it with a different optical card while maintaining existing provisioning.

Step 3 Physically remove the card:

a. Open the card latches/ejectors.

b. Use the latches/ejectors to pull the card forward and away from the shelf.

Step 4 Insert the new card using one of the following procedures as applicable:

D15 Install the Common Control Cards

D16 Install the STM-N Cards

D17 Install the Electrical Cards

D18 Install Ethernet Cards and Connectors

D286 Install the FC_MR-4 Cards

Step 5 As needed, continue with the "D19 Install Fiber-Optic Cables on STM-N Cards" procedure.

Stop. You have completed this procedure.


NTP-D20 Replace the Front Door

Purpose

This procedure replaces the front door and door ground strap after installing cards and fiber-optic cables.

Tools/Equipment

Pinned hex key

Prerequisite Procedures

NTP-D3 Open and Remove the Front Door, page 1-6

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Note Be careful not to crimp any fiber cables that are connected to the STM-N cards or DWDM cards. Some might not have the fiber boot attached.



Step 1 Insert the front door into the hinges on the shelf assembly.

Step 2 Attach the pluggable ground wire (Figure 2-4).

Figure 2-4 ONS 15454 SDH Front Door with Hinges and Ground Wire

Step 3 Swing the door closed.


Note The ONS 15454 SDH comes with a pinned hex key tool for locking and unlocking the front door. Turn the key counterclockwise to unlock the door and clockwise to lock it.


Stop. You have completed this procedure.