Cisco ONS 15454 SDH Procedure Guide, Release 5.0
Chapter 11, Change Card Settings
Downloads: This chapterpdf (PDF - 207.0KB) The complete bookPDF (PDF - 26.98MB) | Feedback

Change Card Settings

Table Of Contents

Change Card Settings

Before You Begin

NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards

NTP-D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards

NTP-D118 Modify Alarm Interface Controller-International Settings

NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection

NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards

NTP-D307 Change Card Service State


Change Card Settings


This chapter explains how to change line and threshold settings on Cisco ONS 15454 SDH cards.

Before You Begin

Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide as necessary.


Caution Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards—As needed, complete this procedure to change line and threshold settings for all electrical cards (E1-N-14, E1-42, E3-12, DS3i-N-12, and STM1E-12).

2. D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards—As needed, complete this procedure to change line and threshold settings for all optical (STM-N) cards.

3. D118 Modify Alarm Interface Controller-International Settings—As needed, complete this procedure to change external alarms and controls and/or orderwire settings.

4. D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection—As needed, complete this procedure to change the protection type on E-1 or DS-3 cards.

5. D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards—As needed, complete this procedure to change the FC_MR-4 card port and threshold settings.

6. D307 Change Card Service State—As needed, complete this procedure to change card service state.

NTP-D88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards

Purpose

This procedure changes the line settings and performance monitoring (PM) parameter thresholds for electrical cards.

Tools/Equipment

None

Prerequisite Procedures

NTP-D17 Install the Electrical Cards, page 2-9

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the electrical card settings. If you are already logged in, proceed to Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4 to preserve the existing database.

Step 3 Perform any of the following tasks as needed:

DLP-D339 Change Line and Threshold Settings for E1-N-14 or E1-42 Cards, page 20-39

DLP-D340 Change Line and Threshold Settings for the E3-12 Cards, page 20-44

DLP-D341 Change Line and Threshold Settings for the DS3i-N-12 Cards, page 20-47

DLP-D342 Change Line and Threshold Settings for the STM1E-12 Card, page 20-52

Step 4 When you are finished changing the card settings, complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Stop. You have completed this procedure.


NTP-D89 Modify Line Settings and PM Parameter Thresholds for STM-N Cards

Purpose

This procedure changes the line settings and the PM parameter thresholds for optical cards.

Tools/Equipment

None

Prerequisite Procedures

NTP-D16 Install the STM-N Cards, page 2-7

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the STM-N card settings. If you are already logged in, proceed to Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Step 3 Perform any of the following tasks as needed:

DLP-D170 Change Line Settings for STM-N Cards, page 18-28

DLP-D343 Change SDH Threshold Settings for STM-N Cards, page 20-55

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Stop. You have completed this procedure.


NTP-D118 Modify Alarm Interface Controller-International Settings

Purpose

This procedure changes the AIC-I card external alarms and controls (environmental alarms) or changes orderwire settings.

Tools/Equipment

None

Prerequisite Procedures

NTP-D247 Provision External Alarms and Controls on the Alarm Interface Controller-International, page 7-8 and the DLP-D83 Provision Orderwire, page 17-75

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the AIC-I card settings. If you are already logged in, proceed to Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Step 3 Perform any of the following tasks as needed:

DLP-D208 Change External Alarms Using the AIC-I Card, page 19-5

DLP-D209 Change External Controls Using the AIC-I Card, page 19-6

DLP-D210 Change AIC-I Card Orderwire Settings, page 19-6

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Stop. You have completed this procedure.


NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection

Purpose

This task converts E1-N-14 and DS3i-N-12 protect cards from 1:1 to 1:N protection.

Tools/Equipment

None

Prerequisite Procedures

DLP-D71 Create a 1:1 Protection Group, page 17-61

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to convert the E1-N-14 and DS3i-N-12 cards from 1:1. If you are already logged in, proceed to Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Step 3 Perform any of the following tasks as needed:

DLP-D176 Convert E1-N-14 Cards From 1:1 to 1:N Protection, page 18-31

DLP-D177 Convert DS3i-N-12 Cards From 1:1 to 1:N Protection, page 18-32

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Stop. You have completed this procedure.


NTP-D311 Modify Port Settings and PM Parameter Thresholds for SAN Cards

Purpose

This procedure changes the line settings and PM parameter thresholds for FC_MR-4 cards.

Tools/Equipment

None

Prerequisite Procedures

NTP-D286 Install the FC_MR-4 Cards, page 2-12

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the OC-N card settings. If you are already logged in, proceed to Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Step 3 Perform any of the following tasks as needed:

DLP-D354 Change General Port Settings for the FC_MR-4 Card, page 20-61

DLP-D355 Change Distance Extension Port Settings for the FC_MR-4 Card, page 20-63

DLP-D356 Change Enhanced FC/FICON Port Settings for the FC_MR-4 Card, page 20-64

DLP-D465 Create FC_MR-4 RMON Alarm Thresholds, page 21-45

DLP-D466 Delete FC_MR-4 RMON Alarm Thresholds, page 21-49

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 15-4.

Stop. You have completed this procedure.


NTP-D307 Change Card Service State

Purpose

This procedure changes card service state.

Tools/Equipment

None

Prerequisite Procedures

Chapter 2, "Install Cards and Fiber-Optic Cable"

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 17-47 at the node where you want to change the card service state.

Step 2 Click the Inventory tab.

Step 3 Click Admin State for the card you want to change, and choose an Admin state from the drop-down list: Unlocked or Locked,maintenance.

Step 4 Click Apply.

Step 5 If an error message opens indicating that the card state cannot be changed from its current state, click OK.

Table 11-1 lists possible card service state transitions based on the Admin State chosen. For more information about the enhanced state model and card state transitions, refer to the "Administrative and Service States" appendix of the Cisco ONS 15454 SDH Reference Manual.

Table 11-1 Cisco ONS 15454 SDH Card State Transitions 

Admin State
Original Service State
Next Service State

Unlocked

Locked-disabled,maintenance & notInstalled

Unlocked-disabled,notInstalled

Unlocked

Locked-disabled,mismatchOfEquipment & maintenance

Unlocked-disabled,mismatchOfEquipment

Unlocked

Locked-enabled,maintenance

Unlocked-enabled

Locked, maintenance

Unlocked-disabled,mismatchOfEquipment

Locked-disabled,maintenance & notInstalled

Locked, maintenance

Unlocked-disabled,automaticInService & notInstalled

Locked-disabled,maintenance & notInstalled

Locked, maintenance

Unlocked-disabled,automaticInService & mismatchOfEquipment

Locked-disabled,mismatchOfEquipment & maintenance

Locked,maintenance

Unlocked-disabled,notInstalled

Locked-disabled,maintenance & notInstalled

Locked,maintenance

Unlocked-enabled

Locked-enabled,maintenance


Stop. You have completed this procedure.