Cisco ONS 15454 SDH Procedure Guide, Releases 4.1.1 and 4.5
Chapter 12, Change Node Settings
Downloads: This chapterpdf (PDF - 473.0KB) The complete bookPDF (PDF - 10.53MB) | Feedback

Change Node Settings

Table Of Contents

Change Node Settings

Before You Begin

NTP-D81 Change Node Management Information

DLP-D140 Change the Node Name, Date, Time, and Contact Information

DLP-D265 Change the Login Legal Disclaimer

NTP-D201 Change CTC Network Access

DLP-D266 Change IP Settings

DLP-D142 Modify a Static Route

DLP-D143 Delete a Static Route

DLP-D144 Disable OSPF

NTP-D241 Modify DWDM Node Settings

DLP-D389 Modify DWDM Hub Node Settings

DLP-D390 Modify DWDM Terminal Node Settings

DLP-D391 Modify DWDM OADM Node Settings

DLP-D392 Modify DWDM Line Node Settings

NTP-D202 Customize the CTC Network View

DLP-D145 Change the Network View Background Color

DLP-D267 Change the Default Network View Background Map

DLP-D268 Apply a Custom Network View Background Map

DLP-D393 Switch Between TDM and DWDM Network Views

DLP-D148 Create Domain Icons

DLP-D149 Manage Domain Icons

DLP-D269 Enable Dialog Box Do-Not-Display Option

NTP-D203 Modify or Delete Card Protection Settings

DLP-D150 Modify a 1:1 Protection Group

DLP-D152 Modify a 1:N Protection Group

DLP-D154 Modify a 1+1 Protection Group

DLP-D270 Modify a Y Cable Protection Group

DLP-D394 Modify a Splitter Protection Group

DLP-D155 Delete a Protection Group

NTP-D204 Delete an SDH DCC Termination

NTP-D241 Delete a DWDM OSC Termination

NTP-D85 Change Node Timing

DLP-D157 Change the Node Timing Source

NTP-D205 Modify Users and Change Security

DLP-D271 Change Node Security Policy—Single Node

DLP-D272 Change Node Security Policy—Multiple Nodes

DLP-D158 Change User Password and Security Level—Single Node

DLP-D160 Change User Password and Security Level—Multiple Nodes

DLP-D315 Log Out a User—Single Node

DLP-D316 Log Out a User—Multiple Nodes

DLP-D159 Delete User—Single Node

DLP-D161 Delete User—Multiple Nodes

NTP-D87 Change SNMP Settings

DLP-D273 Modify SNMP Trap Destination

DLP-D163 Delete SNMP Trap Destination

DLP-D164 Delete Ethernet RMON Alarm Thresholds


Change Node Settings


This chapter explains how to modify node provisioning for the Cisco ONS 15454 SDH. To provision a new node, see Chapter 4, "Turn Up Node." To change default network element settings and to view a list of those settings, refer to the Cisco ONS 15454 Network Element Defaults Handbook for Software Release 4.1 or 4.5.


Note Except where noted, procedures and tasks in this chapter apply to both DWDM (Software R4.5) and non-DWDM (Software R4.1 and earlier) nodes.


Before You Begin

Before performing the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. D81 Change Node Management Information—As needed, complete this procedure to change node name, contact information, latitude, longitude, date, time, and login legal disclaimer.

2. D201 Change CTC Network Access—As needed, complete these procedures to change the IP address, default router, subnet mask, network configuration settings, and static routes.

3. D202 Customize the CTC Network View—As needed, complete this procedure to create domains and customize the appearance of the network map, including specifying a different default map, creating domains, selecting your own map or image, changing the background color.

4. D203 Modify or Delete Card Protection Settings—Complete as needed.

5. D85 Change Node Timing—Complete as needed.

6. D205 Modify Users and Change Security—Complete as needed.

7. D87 Change SNMP Settings—As needed, complete this procedure to modify the node SNMP settings.

NTP-D81 Change Node Management Information

Purpose

This procedure changes the node name, date, time, contact information, or the login legal disclaimer.

Tools/Equipment

None

Prerequisite Procedures

NTP-D25 Set Up Name, Date, Time, and Contact Information, page 4-6

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23 at the node where you want to change the settings. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 Click the Provisioning > General tabs.

Step 4 Complete the "DLP-D140 Change the Node Name, Date, Time, and Contact Information" task.

Step 5 Complete the "DLP-D265 Change the Login Legal Disclaimer" task, as needed.

Step 6 After confirming the changes, complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D140 Change the Node Name, Date, Time, and Contact Information

Purpose

This procedure changes basic information such as node name, date, time, and contact information.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note Changing the date, time, or time zone may invalidate the node's performance monitoring counters.



Step 1 In node view, click the Provisioning > General tabs.

Step 2 Change any of the following:

General: Node Name

General: Contact

Location: Latitude

Location: Longitude

Location: Description


Note To see changes to longitude or latitude on the network map, you must go to network view and right-click the specified node, then click Reset Node Position.


Time: Use SNTP Server

Time: Date (M/D/Y)

Time: Time (H:M:S)

Time: Time Zone

Time: Use Daylight Saving Time

See the "NTP-D25 Set Up Name, Date, Time, and Contact Information" procedure on page 4-6 for detailed field descriptions.

Step 3 Click Apply. Confirm that the changes appear; if not, repeat the task.

Step 4 Return to the your originating procedure (NTP).


DLP-D265 Change the Login Legal Disclaimer

Purpose

This task modifies the legal disclaimer statement shown in the CTC login window so that it will display customer-specific information when users log into the network.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > Security > Legal Disclaimer > HTML tabs.

Step 2 The existing statement is a default, non-customer-specific disclaimer. If you want to edit this statement with specifics for your company, you can change the text. You can also use the following HTML commands to format the text:

<b> Begins boldface font

</b> Ends boldface font

<center> Aligns type in the center of the window

</center> Ends the center alignment

<font=n, where n = point size> Changes the font to the new size

</font> Ends the font size command

<p> Creates a line break

<sub> Begins subscript

</sub> Ends subscript

<sup> Begins superscript

</sup> Ends superscript

<u> Starts underline

</u> Ends underline

Step 3 If you want to preview your changed statement and formatting, click the Preview subtab.

Step 4 Click Apply.

Step 5 Return to the originating procedure (NTP).


NTP-D201 Change CTC Network Access

Purpose

This procedure changes essential network information, including IP settings, static routes, and OSPF options.

Tools/Equipment

None

Prerequisite Procedures

NTP-D169 Set Up CTC Network Access, page 4-7

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note Additional ONS 15454 SDH networking information and procedures, including IP addressing examples, static route scenarios, Open Shortest Path First (OSPF) protocol, and routing information protocol options are provided in the IP Networking section of the Cisco ONS 15454 SDH Reference Manual.



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 Perform any of the following tasks as needed:

D266 Change IP Settings

D142 Modify a Static Route

D143 Delete a Static Route

D144 Disable OSPF

DLP-D250 Set Up or Change Open Shortest Path First Protocol, page 4-14.

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D266 Change IP Settings

Purpose

This task changes the IP address, subnet mask, default router, DHCP access, firewall access, and proxy server settings for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Caution Changing the node IP address, subnet mask, or IIOP listener port causes the TCC2s to reboot. If Ethernet circuits using spanning tree protocol originate or terminate on E Series Ethernet cards installed in the node, circuit traffic will be lost for several minutes while the spanning trees reconverge. Other circuits are not affected by TCC2 reboots.


Step 1 In node view, click the Provisioning > Network > General tabs.

Step 2 Change any of the following:

IP Address

Suppress CTC IP Display

LCD IP Setting

Default Router

Subnet Mask Length

Forward DHCP Request To

TCC CORBA (IIOP) Listener Port

Gateway Settings

See the "DLP-D249 Provision IP Settings" task on page 4-8 for detailed field descriptions.

Step 3 Click Apply.

If you changed a network field that will cause the node to reboot—IP address, default router, subnet mask, TCC CORBA Listener Port, the Change Network Configuration confirmation dialog box appears. If you changed a gateway setting, a confirmation appropriate to the gateway field appears.

Step 4 If a confirmation dialog box appears, click Yes.

If you changed an IP address, subnet mask length, or TCC CORBA (IIOP) Listener Port, both ONS 15454 SDH TCC2 cards will reboot, one at a time.

Step 5 Confirm that the changes appear. If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide, as necessary.

Step 6 Return to your originating procedure (NTP).


DLP-D142 Modify a Static Route

Purpose

This task modifies a static route on an ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Network tabs.

Step 2 Click the Static Routing tab.

Step 3 Click the static route you want to edit.

Step 4 Click Edit.

Step 5 In the Edit Selected Static Route dialog box, enter the following:

Mask

Next Hop

Cost

See the "DLP-D65 Create a Static Route" task on page 4-13 for detailed field descriptions.

Step 6 Click OK.

Step 7 Return to your originating procedure (NTP).


DLP-D143 Delete a Static Route

Purpose

This task deletes an existing static route on an ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Network > Static Routing tabs.

Step 2 Click the static route you want to delete.

Step 3 Click Delete. A confirmation dialog box appears.

Step 4 Click Yes.

Step 5 Return to your originating procedure (NTP).


DLP-D144 Disable OSPF

Purpose

This task disables the Open Shortest Path First (OSPF) routing protocol process for an ONS 15454 SDH LAN.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note Disabling OSPF can cause a TCC2 reboot. A TCC2 reboot causes a temporary loss of connectivity to the node, but traffic is unaffected.



Step 1 In node view, click the Provisioning > Network > OSPF tabs. The OSPF subtab has several options.

Step 2 In the OSPF on LAN area, uncheck the OSPF active on LAN check box.

Step 3 Click Apply. Confirm that the changes appear; if not, repeat the task.

Step 4 Return to your originating procedure (NTP).


NTP-D241 Modify DWDM Node Settings

Purpose

This procedure sets the network and system settings and provisions the node power levels on ONS 15454 SDH nodes that are provisioned for DWDM. This procedure applies only to DWDM nodes.

Tools/Equipment

A node provisioning plan prepared by Cisco MetroPlanner is required.

Prerequisite Procedures

You must use Cisco MetroPlanner or another DWDM network calculation tool to prepare a configuration file for your network.

NTP-D237 Provision the DWDM Node, page 5-3

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Caution DWDM settings are normally not changed at the individual node level. Any change to a DWDM node setting usually requires recalculation of power and attenuation levels at other nodes on the DWDM network. Do not change a DWDM node setting unless you are prepared to modify the settings of other DWDM nodes on the network.


Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Perform one of the following tasks as necessary:

D389 Modify DWDM Hub Node Settings

D390 Modify DWDM Terminal Node Settings

D391 Modify DWDM OADM Node Settings

D392 Modify DWDM Line Node Settings

Step 3 Click the Connections tab, then click Calculate Connections.

Step 4 Verify that every connection matches the connections specified by the Cisco MetroPlanner design plan. If a connection is not correct:

a. Delete the connection. See the "DLP-D377 Delete a DWDM Connection" task on page 5-11.

b. Uninstall the fibers from the incorrect slot/unit/port.

c. Connect the fiber to the correct slot/unit/port.

d. Create a new connection. See the "DLP-D378 Create a DWDM Connection" task on page 5-11.

Step 5 Click the Port Status tab. Click Launch ANS. ANS (Automatic Node Setup) adjusts the values of the variable optical attenuators (VOAs) to equalize the per channel power at the amplifier level.

Stop. You have completed this procedure.


DLP-D389 Modify DWDM Hub Node Settings

Purpose

This task modifies the network and system types and sets the channel power levels for a DWDM hub node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > WDS-ANS > Provisioning tabs.

Step 2 Complete the fields shown in Table 5-1 on page 5-5.

Step 3 Click Apply.

Step 4 Return to your originating procedure (NTP).


DLP-D390 Modify DWDM Terminal Node Settings

Purpose

This task provisions the network and system types and power levels for a DWDM terminal node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > WDS-ANS > Provisioning tabs.

Step 2 Complete the fields shown in Table 5-3 on page 5-6.

Step 3 Click Apply.

Step 4 Return to your originating procedure (NTP).


DLP-D391 Modify DWDM OADM Node Settings

Purpose

This task provisions the network and system types and power levels for a DWDM optical add/drop module (OADM) node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > WDS-ANS > Provisioning tabs.

Step 2 Complete the fields shown in Table 5-4 on page 5-7.

Step 3 Click Apply.

Step 4 Return to your originating procedure (NTP).


DLP-D392 Modify DWDM Line Node Settings

Purpose

This task modifies the network and system types for a DWDM line node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > WDS-ANS > Provisioning tabs.

Step 2 Complete the fields shown in Table 5-6 on page 5-10.

Step 3 Click Apply.

Step 4 Return to your originating procedure (NTP).


NTP-D202 Customize the CTC Network View

Purpose

Use this procedure modifies the CTC network view, including grouping nodes into domains for a less-cluttered display, changing the network view background color, and using a custom image for the network view background.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the following tasks, as needed:

D145 Change the Network View Background Color

D267 Change the Default Network View Background Map

D268 Apply a Custom Network View Background Map

D148 Create Domain Icons

D149 Manage Domain Icons

D269 Enable Dialog Box Do-Not-Display Option

Stop. You have completed this procedure.


DLP-D145 Change the Network View Background Color

Purpose

Use this task to change the network view background color or the domain view background color (the area displayed when you open a domain).

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher



Note If you modify background colors, the change is stored in your CTC user profile on the computer. The change does not affect other CTC users.



Step 1 From the View menu choose Go to Network View.

Step 2 If you want to change a domain background, double-click the domain. If not, continue with Step 3.

Step 3 Right-click the network view or domain map area and choose Set Background Color from the shortcut menu.

Step 4 In the Choose Color dialog box, select a background color.

Step 5 Click OK.

Step 6 Return to your originating procedure (NTP).


DLP-D267 Change the Default Network View Background Map

Purpose

This task changes the default map of the CTC network view.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note If you modify the background image, the change is stored in your CTC user profile on the computer. The change does not affect other CTC users.



Step 1 From the View menu choose Go to Network View.

Step 2 From the Edit menu, choose Preferences.

Step 3 In the Preferences dialog box, click the Map tab, then check the Use Default Map check box if it is not already selected.

Step 4 Click the Default Maps field and choose a default map from the drop-down menu. Map choices are: Germany, Japan, Netherlands, South Korea, United Kingdom, and the United States (default).

Step 5 Click Apply. The new network map is displayed.

Step 6 Click OK.

Step 7 If the ONS 15454 SDH icons are not visible, right-click the network view and choose Zoom Out. Repeat until all the ONS 15454 SDH icons are visible. (You can also choose Fit Graph to Window.)

Step 8 If you need to reposition the node icons, drag and drop them one at a time to a new location on the map.

Step 9 If you want to change the magnification of the icons, right-click the network view and choose Zoom In. Repeat until the ONS 15454 SDH icons are displayed at the magnification you want.

Step 10 Return to your originating procedure (NTP).


DLP-D268 Apply a Custom Network View Background Map

Purpose

This task changes the background image or map on the CTC network view.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher



Note You can replace the network view background image with any JPEG or GIF image that is accessible on a local or network drive. If you apply a custom image, the change is stored in your CTC user profile on the computer. The change does not affect other CTC users. The change does not affect other CTC users.



Step 1 From the View menu choose Go to Network View.

Step 2 Right-click the network or domain map and select Set Background Image.

Step 3 Click Browse. Navigate to the graphic file you want to use as a background.

Step 4 Select the file. Click Open.

Step 5 Click Apply and then click OK.

Step 6 If the ONS 15454 SDH icons are not visible, right-click the network view and choose Zoom Out. Repeat this step until all the ONS 15454 SDH icons are visible.

Step 7 If you need to reposition the node icons, drag and drop them one at a time to a new location on the map.

Step 8 If you want to change the magnification of the icons, right-click the network view and choose Zoom In. Repeat until the ONS 15454 SDH icons are displayed at the magnification you want.

Step 9 At the network view, use the CTC toolbar Zoom buttons (or right-click the graphic area and select a Zoom command from the shortcut menu) to set the area of the image you want to view.

Step 10 Return to your originating procedure (NTP).


DLP-D393 Switch Between TDM and DWDM Network Views

Purpose

Use this task to switch between TDM (Time Division Multiplexing) and DWDM (Dense Wavelength Division Multiplexing) network views. This task applies only to Release 4.5 or later.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Retrieve or higher



Step 1 From the View menu choose Go to Network View.

Step 2 From the Network View drop-down menu, choose one of the following:

All—Displays both TDM and DWDM nodes

TDM—Only displays ONS 15454 SDH nodes with SONET or SDH cards including the transponder and muxponder cards.

DWDM—Only displays ONS 15454 SDH nodes with DWDM cards, including the transponder and muxponder cards.

Step 3 Return to your originating procedure (NTP).


DLP-D148 Create Domain Icons

Purpose

This task creates a domain icon, which can be used to group ONS 15454 SDH icons in CTC network view.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note Domains you create will be seen by all users who log into the network.



Step 1 From the View menu choose Go to Network View.

Step 2 Right-click the network map and choose Create New Domain from the shortcut menu.

Step 3 When the domain icon appears on the map, click the map name and type the domain name.

Step 4 Press Enter.

Step 5 To add nodes to the domain, continue with the "DLP-D149 Manage Domain Icons" task.

Step 6 Return to your originating procedure (NTP).


DLP-D149 Manage Domain Icons

Purpose

This task manages CTC network view domain icons.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

D148 Create Domain Icons

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note All domain changes, such as added or removed node icons, are visible to all users who log into the network.



Step 1 From the View menu choose Go to Network View.

Step 2 Locate the domain action you want in Table 12-1 and complete the appropriate steps.

Table 12-1 Managing Domains 

Domain action
Steps

Move a domain

Drag and drop the domain icon to the new location.

Rename a domain

Right-click the domain icon and choose Rename Domain from the shortcut menu. Type the new name in the domain name field.

Add a node to a domain

Drag and drop the node icon to the domain icon.

Move a node from a domain to the network map

Open the domain and right-click a node. Select Move Node Back to Parent View.

Open a domain

Double-click the domain icon.

Right-click the domain and choose Open Domain.

Return to network view

Right-click the domain view area and choose Go to Parent View from the shortcut menu.

Preview domain contents

Right-click the domain icon and choose Show Domain Overview. The domain icon shows a small preview of the nodes in the domain. To turn off the domain overview, right-click the overview and select Show Domain Overview.

Remove domain

Right-click the domain icon and choose Remove Domain. Any nodes residing in the domain are returned to the network map.


Step 3 Return to your originating procedure (NTP).


DLP-D269 Enable Dialog Box Do-Not-Display Option

Purpose

This task ensures that a user-selected "Do not display" dialog box preference is enabled for subsequent sessions, or to disable the do not display option.

Tools/Equipment

None

Prerequisite procedures

DLP-D60 Log into CTC, page 3-23

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note If any user who has rights to perform an operation (for example, creating a circuit) selects the "Do not show this dialog again" check box on a dialog box, the dialog box is not displayed for any other users who perform that operation on the network from the same computer unless the command is overridden using the following task. (The preference is stored on the CTC computer, not in the node database.)



Step 1 From the Edit menu, choose Preferences.

Step 2 In the Preferences dialog box, click the General tab.

The Preferences Management area field lists all dialog boxes where "Do not show this dialog again." was checked.

Step 3 Choose one of the following, or uncheck the individual dialog boxes that you want to appear:

Don't Show Any—Hides all do-not-display check boxes.

Show All—Overrides do-not-display check box selections and displays all dialog boxes.

Step 4 Click OK.

Step 5 Return to your originating procedure (NTP).


NTP-D203 Modify or Delete Card Protection Settings

Purpose

This procedure modifies or deletes card protection settings.

Tools/Equipment

None

Prerequisite Procedures

NTP-D170 Create Protection Groups, page 4-25

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Caution Modifying and deleting protection groups can be service affecting.


Step 1 Compete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 Perform any of the following tasks as needed:

D150 Modify a 1:1 Protection Group

D152 Modify a 1:N Protection Group

D154 Modify a 1+1 Protection Group

D270 Modify a Y Cable Protection Group

D155 Delete a Protection Group

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D150 Modify a 1:1 Protection Group

Purpose

This task modifies a 1:1 protection group for electrical (E1-N-14, E3-12, and DS3i-N-12) cards.

Tools/Equipment

None

Prerequisite Procedures

DLP-D71 Create a 1:1 Protection Group, page 4-26

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Protection tabs.

Step 2 In the Protection Groups area, click the 1:1 protection group you want to modify.

Step 3 In the Selected Group area, you can modify the following, as needed:

Name—As needed, type the changes to the protection group name. The name can have up to 32 alphanumeric characters.

Revertive—Check this box if you want traffic to revert to the working card after failure conditions stay corrected for the amount of time chosen from the Reversion Time menu. Uncheck if you do not want traffic to revert.

Reversion time—If the Revertive check box is selected, choose the reversion time from the Reversion time drop-down menu. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working card. Traffic can revert when conditions causing the switch are cleared.

Step 4 Click Apply. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide.



Note To convert electrical groups, see the "NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection" procedure on page 13-53.


Step 5 Return to your originating procedure (NTP).


DLP-D152 Modify a 1:N Protection Group

Purpose

This task modifies a 1:N protection group for E1-N-14 and DS-3i-N-12 cards.

Tools/Equipment

None

Prerequisite Procedures

DLP-D72 Create a 1:N Protection Group, page 4-27

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Verify that the E1-N-14 and DS-3i-N-12 cards are installed according to the 1:N specifications in the "DLP-D72 Create a 1:N Protection Group" task on page 4-27.

Step 2 In node view, click the Provisioning > Protection tabs.

Step 3 In the Protection Groups area, click the 1:N protection group you want to modify.

Step 4 In the Selected Group area, change any of the following, as needed:

Name—As needed, type the changes to the protection group name. The name can have up to 32 alphanumeric characters.

Available Cards—If cards are available, they will appear here. Use the arrow buttons to move them into the Working Cards column.

Working Cards—Use the arrow buttons to move cards out of the Working Cards column.

Reversion Time—Choose a reversion time from the drop-down menu. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working card. Traffic can revert when conditions causing the switch are cleared.

See the "DLP-D72 Create a 1:N Protection Group" task on page 4-27 for field descriptions.

Step 5 Click Apply. The changes are applied. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide.



Note To convert electrical protection groups, see the "NTP-D91 Upgrade E1-N-14 and DS3 i-N-12 Protect Cards from 1:1 Protection to 1:N Protection" procedure on page 13-53.


Step 6 Return to your originating procedure (NTP).


DLP-D154 Modify a 1+1 Protection Group

Purpose

This task modifies a 1+1 protection group for any optical port (STM-1, STM-4, STM-16, STM-64).

Tools/Equipment

None

Prerequisite Procedures

DLP-D73 Create a 1+1 Protection Group, page 4-28

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Protection tabs.

Step 2 In the Protection Groups area, click the 1+1 protection group you want to modify.

Step 3 In the Selected Group area, you can modify the following:

Name—As needed, type the changes to the protection group name. The name can have up to 32 alphanumeric characters.

Bidirectional switching—As needed, check or uncheck.

Revertive—Check this box if you want traffic to revert to the working card after failure conditions stay corrected for the amount of time chosen from the Reversion Time menu. Uncheck if you do not want traffic to revert.

Reversion time—If the Revertive check box is selected, choose the reversion time from the Reversion time drop-down menu. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working card. Traffic can revert when conditions causing the switch are cleared.

See the "DLP-D73 Create a 1+1 Protection Group" task on page 4-28 for field descriptions.

Step 4 Click Apply. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide, as needed.


Step 5 Return to your originating procedure (NTP).


DLP-D270 Modify a Y Cable Protection Group

Purpose

This task modifies a Y Cable protection group for any client port on a MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, TXPP_MR_2.5G card.

Tools/Equipment

None

Prerequisite Procedures

DLP-D252 Create a Y Cable Protection Group, page 4-29

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Protection tabs.

Step 2 In the Protection Groups area, click the Y Cable protection group you want to modify.

Step 3 In the Selected Group area, you can modify the following:

Name—As needed, type the changes to the protection group name. The name can have up to 32 alphanumeric characters.

Revertive—Check this box if you want traffic to revert to the working card after failure conditions stay corrected for the amount of time chosen from the Reversion Time menu. Uncheck if you do not want traffic to revert.

Reversion time—If the Revertive check box is selected, choose the reversion time from the Reversion time drop-down menu. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working card. Traffic can revert when conditions causing the switch are cleared.

See the "DLP-D252 Create a Y Cable Protection Group" task on page 4-29 for field descriptions.

Step 4 Click Apply. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide.


Step 5 Return to your originating procedure (NTP).


DLP-D394 Modify a Splitter Protection Group

Purpose

This task modifies a Splitter protection group for any client port on a TXPP_MR_2.5G card. Splitter protection is automatically created when the TXPP transponder card is installed.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > Protection tabs.

Step 2 In the Protection Groups area, click the Splitter protection group you want to modify.

Step 3 In the Selected Group area, you can modify the following:

Name—As needed, type the changes to the protection group name. The name can have up to 32 alphanumeric characters.

Revertive—Check this box if you want traffic to revert to the working card after failure conditions stay corrected for the amount of time chosen from the Reversion Time menu. Uncheck if you do not want traffic to revert.

Reversion time—If the Revertive check box is selected, choose the reversion time from the Reversion time pull-down menu. The range is 0.5 to 12.0 minutes. The default is 5.0 minutes. This is the amount of time that will elapse before the traffic reverts to the working card. Traffic can revert when conditions causing the switch are cleared.

Step 4 Click Apply. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 Troubleshooting Guide, as needed.


Step 5 Return to your originating procedure (NTP).


DLP-D155 Delete a Protection Group

Purpose

This task deletes a 1:1, 1:N, 1+1, or Y Cable protection group.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In the node view, click the Provisioning > Protection tabs.

Step 2 In the Protection Groups area, click the protection group you want to delete.

Step 3 Click Delete.

Step 4 Click Yes in the Delete Protection Group dialog box to confirm deletion. Confirm that the changes appear; if they do not, repeat Steps 1 through 3.

Step 5 Return to your originating procedure (NTP).


NTP-D204 Delete an SDH DCC Termination

Purpose

This procedure deletes a SDH DCC termination on the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D253 Provision SDH DCC Terminations, page 6-5

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note Deleting a DCC termination may cause you to lose visibility of nodes that do not have other DCCs or network connections to the CTC computer.



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2

Step 2 In node view, click the Provisioning > DCC/GCC tabs.


Note This tab is labeled DCC/GCC in Software R4.1 and DCC/GCC/OSC in Software R4.5.


Step 3 Click the DCC termination and click Delete. The Delete SDCC Termination dialog box opens.

Step 4 Check the Set Port Out of Service box if you want to change the port state to out of service (this may be service affecting).

Step 5 Click Yes on the confirmation dialog box to confirm. Confirm that the changes appear.

Stop. You have completed this procedure.


NTP-D241 Delete a DWDM OSC Termination

Purpose

Use this procedure to delete a DWDM OSC termination on the ONS 15454. This procedure only applies to DWDM nodes.

Tools/Equipment

None

Prerequisite Procedures

DLP-D380 Provision OSC Terminations, page 7-5

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Caution Deleting a OSC termination may cause node isolation and loss of visibility to nodes that do not have other OSCs or network connections to the CTC computer.


Step 1 In node view, click the Provisioning > DCC/GCC/OSC > OSC tabs.

Step 2 Click the OSC termination to be deleted and click Delete.

Step 3 In the Delete OSC Termination confirmation box, click Yes to confirm. Confirm that the changes appear.

Until all network OSC terminations are deleted, the following alarms might appear: EOC (SDCC Termination Failure) and power failure alarms on the OPT-BST and OSC-CSM, such as TRUE LOS alarms.

Stop. You have completed this procedure.


NTP-D85 Change Node Timing

Purpose

This procedure changes the SDH timing settings for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D28 Set Up Timing, page 4-20

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 As needed, complete the "DLP-D157 Change the Node Timing Source" task.

Step 4 If you need to change any internal timing settings, follow the "DLP-D70 Set Up Internal Timing" task on page 4-23 for the settings you need to modify.


Caution Internal timing is Stratum 3 and not intended for permanent use. All ONS 15454 SDHs should be timed to a Stratum 2 or better primary reference source.

Step 5 If you need to verify timing after removing a node from an MS-SPRing or SNCP ring, see the "DLP-D195 Verify Timing in a Reduced Ring" task on page 16-12.

Step 6 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D157 Change the Node Timing Source

Purpose

This task changes the SDH timing source for the ONS 15454 SDH

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Caution The following procedure may be service affecting and should be performed during a scheduled maintenance window.


Step 1 In node view, click the Provisioning > Timing tabs.

Step 2 In the General Timing section, change any of the following information:

Timing Mode


Note Because mixed timing can cause timing loops, Cisco does not recommend using the Mixed Timing option. Use this mode with care.


SSM Message Set

Quality of RES

Revertive

Reversion Time

See the "DLP-D69 Set Up External or Line Timing" task on page 4-21 for field descriptions.

Step 3 In the BITS Facilities section, you can change the following information:


Note The BITS Facilities section sets the parameters for your BITS1 and BITS2 timing references. Many of these settings are determined by the timing source manufacturer. If equipment is timed through BITS Out, you can set timing parameters to meet the requirements of the equipment.


State

Coding

Framing

Sync Messaging

AIS Threshold

LBO

Step 4 In the Reference Lists area, you can change the following information:


Note Reference lists define up to three timing references for the node and up to six BITS Out references. BITS Out references define the timing references used by equipment that can be attached to the node's BITS pins on the MIC-C/T/P. If you attach equipment to BITS Out pins, you normally attach it to a node with Line mode because equipment near the external timing reference can be directly wired to the reference.


NE Reference

BITS 1 Out

BITS 2 Out

Step 5 Click Apply. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Reference Manual for information about timing.



Note Refer to the Cisco ONS 15454 SDH Reference Manual for timing information.


Step 6 Return to your originating procedure (NTP).


NTP-D205 Modify Users and Change Security

Purpose

This procedure modifies user and security properties for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D30 Create Users and Assign Security, page 4-3

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 Perform any of the following tasks as needed:

D271 Change Node Security Policy—Single Node

D272 Change Node Security Policy—Multiple Nodes

D158 Change User Password and Security Level—Single Node

D160 Change User Password and Security Level—Multiple Nodes

D159 Delete User—Single Node

D161 Delete User—Multiple Nodes

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D271 Change Node Security Policy—Single Node

Purpose

This task changes the security policy for a single node, including idle user timeouts, user lock outs, password changes, and concurrent login policies.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > Security > Policy tabs.

Step 2 In the Idle User Timeout area, you can modify the timeout times by clicking the hour (H) and minute (M) arrows. You can choose values between 0 and 16 hours, and 0 and 59 minutes.

Step 3 In the User Lockout area, you can modify the following:

Failed Logins Before Lockout—Choose the number of failed login attempts a user can make before the user is locked out from the node. You can choose a value between 0 and 10.

Manual Unlock by Superuser—Select this check box if you want to allow a user with Superuser privileges to manually unlock a user who has been locked out from a node.

Lockout Duration—Choose the amount of time the user will be locked out after a failed login. You can choose a value between 0 and 10 minutes, and 0 and 55 seconds (in five-second intervals).

Step 4 In the Concurrent Logins area, click Single Session Per User if you want to limit users to a single login session.

Step 5 In the Password Change area, you can modify the following:

Require [nn] different passwords...—Choose a value between 1 and 10 to determine how many different passwords have to be created before a password can be reused.

...or a waiting period of [nn] days before password reuse—Choose a value between 0 and 30 days to set the amount of time (in days) before a password can be reused.

In other words, users can change their password after they meet one of the two conditions. For example, if you set the number of different passwords to 5 and the number of days to 20, the user can reuse their password after changing it five times or after 20 days elapse, whichever occurs first.

Step 6 Click Apply. Confirm that the changes appear.

Step 7 Return to your originating procedure (NTP).


DLP-D272 Change Node Security Policy—Multiple Nodes

Purpose

This task changes the security policy for multiple nodes including idle user timeouts, user lock outs, password change, and concurrent login policies.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 From the View menu choose Go to Network View.

Step 2 Click the Provisioning > Security > Policy tabs. A read-only table of nodes and their policies is displayed.

Step 3 Click a node on the table that you want to modify, then click the Change button.

Step 4 In the Idle User Timeout area, you can modify the timeout times by clicking the hour (H) and minute (M) arrows. You can choose values between 0 and 16 hours, and 0 and 59 minutes.

Step 5 In the User Lockout area, you can modify the following:

Failed Logins Before Lockout—Choose the number of failed login attempts a user can make before the user is locked out from the node. You can choose a value between 0 and 10.

Manual Unlock by Superuser—Select this check box if you want to allow a user with Superuser privileges to manually unlock a user who has been locked out from a node.

Lockout Duration—Choose the amount of time the user will be locked out after a failed login. You can choose a value between 0 and 10 minutes, and 0 and 55 seconds (in five-second intervals).

Step 6 Under Concurrent Logins, click Single Session Per User if you want to limit users to a single login session.

Step 7 Under Password Change, you can modify the following:

Require [nn] different passwords...—Choose the number of different passwords that have to be created before a password can be reused. You can choose a value between 0 and 10 days.

...or a waiting period of [nn] days before password reuse—Choose the number of days the user must wait before reusing a password. You can choose a value between 0 and 30 days.

In other words, users can change their password after they meet one of the two conditions. For example, if you set the number of different passwords to 5 and the number of days to 20, the user can reuse their password after changing it five times or after 20 days elapse, whichever occurs first.

Step 8 Under Select Applicable Nodes, deselect any nodes where you don't want to apply the changes.

Step 9 Click OK.

Step 10 On the Security Policy Change Results dialog box, confirm that the changes succeeded, then click OK.

Step 11 Return to your originating procedure (NTP).


DLP-D158 Change User Password and Security Level—Single Node

Purpose

Use this task to change settings for an existing user at one node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > Security > Users tabs.

Step 2 Click the user whose settings you want to modify.

Step 3 Click Change.

Step 4 In the Change User dialog box, under Selected User, you can:

Change the existing user password

Change the existing user security level

Lock out the user

See the "NTP-D30 Create Users and Assign Security" procedure on page 4-3 for field descriptions.

Step 5 Click OK.


Note User settings that you changed during this task will not appear until that user logs off and logs back in again.


Step 6 Return to your originating procedure (NTP).


DLP-D160 Change User Password and Security Level—Multiple Nodes

Purpose

Use this task to modify an existing user's settings for multiple nodes.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed; use this procedure to add users to multiple nodes at one time

Onsite/Remote

Onsite or remote

Security Level

Superuser



Note You must add the same user name and password to each node the user will access.



Step 1 From the View menu, choose Go to Network View. Verify that all the nodes where you want to add users are accessible.

Step 2 Click the Provisioning > Security > Users tabs. Highlight the user's name whose settings you want to change.

Step 3 Click Change. The Change User dialog box appears.

Step 4 In the Change User dialog box, enter the following:

New Password

Confirm New Password

Security Level

See the "DLP-D75 Create a New User—Multiple Nodes" task on page 4-5 for field descriptions.

Step 5 Under "Select applicable nodes," uncheck any nodes where you do not want to change the user's settings (all network nodes are selected by default).

Step 6 Click OK. A Change Results confirmation dialog box appears.

Step 7 Click OK to acknowledge the changes. Confirm that the changes appear; if not, repeat the task.

Step 8 Return to your originating procedure (NTP).


DLP-D315 Log Out a User—Single Node

Purpose

This task logs out a user from a single node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 In node view, click the Provisioning > Security > Active Logins tabs.

Step 2 Choose the user you want to log out and click Logout.

Step 3 In the Logout User dialog box, check Lockout before Logout if you want to lock the user out. This prevents the user from logging in after logout based on parameters set under User Lockouts in the Policy tab. Either a manual unlock by a Superuser is required, or the user is locked out for the amount of time specified in the Lockout Duration field. See the "DLP-D271 Change Node Security Policy—Single Node" task for more information.

Step 4 Click OK.

Step 5 Click Yes to confirm the logout.

Step 6 Return to your originating procedure (NTP).


DLP-D316 Log Out a User—Multiple Nodes

Purpose

This task logs out a user from multiple nodes.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 From the view menu, chose Go to Network View.

Step 2 Click the Provisioning > Security > Active Logins tabs.

Step 3 Choose the user you want to log out.

Step 4 Click Logout.

Step 5 In the Logout User dialog box, check the nodes where you want to log out the user.

Step 6 In the Logout User dialog box, check Lockout before Logout if you want to lock the user out prior to logout. This prevents the user from logging in after logout based on parameters set under User Lockouts in the Policy tab. Either a manual unlock by a Superuser is required, or the user is locked out for the amount of time specified in the Lockout Duration field. See the "DLP-D272 Change Node Security Policy—Multiple Nodes" task for more information.

Step 7 In the Select Applicable Nodes area, deselect any nodes where you do not want to change the user's settings (all network nodes are selected by default).

Step 8 Click OK.

Step 9 In the User Change dialog box, click OK.

Step 10 Return to your originating procedure (NTP).


DLP-D159 Delete User—Single Node

Purpose

This task deletes an existing user from a single node.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Note You cannot delete a user who is currently logged in. To log out a user, you can complete the "DLP-D315 Log Out a User—Single Node" task, or you can choose the "Logout before delete" option on the Delete User dialog box.



Note CTC will allow you to delete other Superusers if one Superuser remains. For example, you can delete the CISCO15 user if you have created another Superuser. Use this option with caution.



Step 1 In node view, select the Provisioning > Security > Users tabs.

Step 2 Choose the user you want to delete.

Step 3 Click Delete.

Step 4 In the Delete User dialog box, verify that the user name displayed is the one you want to delete. Click Logout before delete? if the user is currently logged in. (You cannot delete users if they are logged in.)

Step 5 Click OK. Confirm that the changes appear; if not, repeat the task.

Step 6 Return to your originating procedure (NTP).


DLP-D161 Delete User—Multiple Nodes

Purpose

This task deletes an existing user from multiple nodes.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Note You cannot delete a user who is currently logged in. To log out a user, you can complete the "DLP-D316 Log Out a User—Multiple Nodes" task, or you can choose the "Logout before delete" option on the Delete User dialog box.



Note CTC will allow you to delete other Superuser IDs as long as one Superuser ID remains. For example, you can delete the CISCO15 user if you have created another Superuser ID. Use this option with caution.



Step 1 From the View menu, choose Go to Network View.

Step 2 Click the Provisioning > Security > Users tabs. Highlight the name of the user you want to delete.

Step 3 Click Delete. The Delete User dialog box appears.

Step 4 Click OK. A Change Results confirmation dialog box appears.

Step 5 Click OK to acknowledge the changes. Confirm that the changes appear; if not, repeat the task.

Step 6 Return to your originating procedure (NTP).


NTP-D87 Change SNMP Settings

Purpose

This procedure modifies SNMP settings for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D171 Set Up SNMP, page 4-31

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser



Step 1 Complete the "DLP-D60 Log into CTC" task on page 3-23. If you are already logged in, continue with Step 2.

Step 2 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Step 3 Perform any of the following tasks as needed:

D273 Modify SNMP Trap Destination

D163 Delete SNMP Trap Destination

D164 Delete Ethernet RMON Alarm Thresholds

Step 4 Complete the "NTP-D108 Back Up the Database" procedure on page 17-8.

Stop. You have completed this procedure.


DLP-D273 Modify SNMP Trap Destination

Purpose

Use this task to modify the SNMP trap destination on an ONS 15454 SDH including community name, default UDP port, SNMP trap version, and maximum traps per second.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > SNMP tabs.

Step 2 Select a trap in the Trap Destinations dialog box.

For a description of SNMP traps, see the Cisco ONS 15454 SDH Reference Manual.

Step 3 Type the SNMP community name in the Community Name field.


Note The community name is a form of authentication and access control. The community name assigned to the ONS 15454 SDH is case-sensitive and must match the community name of the network management system.



Note The default UDP port for SNMP is 162.


Step 4 Set the Trap Version field for either SNMPv1 or SNMPv2.

Refer to your NMS documentation to determine whether to use SNMP v1 or v2.

Step 5 Set your maximum traps per second in the Max Traps per Second field.


Note The Max Traps per Second is the maximum number of traps per second that will be sent to the SNMP manager. If the field is set to 0, there is no maximum and all traps are sent.


Step 6 If you want to allow the ONS 15454 SDH SNMP agent to accept SNMP SET requests on certain MIBs, check the Allow SNMP Sets check box. If the box is not checked, SET requests are rejected.

Step 7 Click Apply.

Step 8 SNMP settings are now configured. To view SNMP information for each node, highlight the node IP address in the Trap Destinations area of the Trap Destinations screen. Confirm that the changes appear.


Note If the changes do not appear, repeat the task. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide.


Step 9 Return to your originating procedure (NTP).


DLP-D163 Delete SNMP Trap Destination

Purpose

This task deletes SNMP trap destinations on an ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Step 1 In node view, click the Provisioning > SNMP tabs.

Step 2 In the Trap Destinations area, click the trap you want to delete.

Step 3 Click Delete. A confirmation dialog box appears.

Step 4 Click Yes. Confirm that the changes appear; if not, repeat the task.

Step 5 Return to your originating procedure (NTP).


DLP-D164 Delete Ethernet RMON Alarm Thresholds

Purpose

This task deletes remote monitoring (RMON) threshold crossing alarms for Ethernet ports.

Tools/Equipment

None

Prerequisite Procedures

NTP-D34 Create Ethernet RMON Alarm Thresholds, page 4-32

DLP-D60 Log into CTC, page 3-23

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher



Note The ONS 15454 SDH ML-Series card uses the Cisco IOS CLI for managing RMON.



Step 1 In node view, click the Provisioning > Ether Bridge > Thresholds tabs.

Step 2 Click the RMON alarm threshold you want to delete.

Step 3 Click Delete. The Delete Threshold dialog box opens.

Step 4 Click Yes to delete that threshold.

Step 5 Return to your originating procedure (NTP).