Alert and Error Messages
This appendix identifies all alert and error messages that Cisco Broadband Access Center (Cisco BAC) generates, specifically:
•RDU Alerts
•DPE Alerts
•Watchdog Alerts
•Network Registrar Extension Point Alerts
Cisco BAC generates alerts through the Syslog service. Syslog is a client-server protocol that manages the logging of information on Solaris. Cisco BAC syslog alerts are not a logging service; they provide a notification that a problem exists, but do not necessarily define the specific cause of the problem. You might find this information in the appropriate Cisco BAC log files.
Message Format
When Cisco BAC generates an alert message, the format is:
XXX-#-####: Message
•XXX—Identifies the facility code, which can include:
–RDU (Regional Distribution Unit)
–DPE (Device Provisioning Engine)
–AGENT (rduSnmpAgent or dpeSnmpAgent)
–NR_EP (Cisco Network Registrar extension points)
–KDC (Key Distribution Center)
•#—Identifies the severity level in use. Table A-1 describes the different levels.
Table A-1 Severity Levels for Alert Messages
|
|
1 |
Identifies an alert |
2 |
Identifies a critical alert |
3 |
Identifies an error |
6 |
Identifies an informational message |
•###—Identifies the numeric error code.
•Message—Provides the alert text or message.
RDU Alerts
Table A-2 identifies the RDU alerts.
Table A-2 RDU Alerts
|
|
RDU-1-101: RDU ran out of disk space |
Indicates that the storage partition of the RDU server ran out of space. After encountering this error, the RDU attempts to restart automatically, but will typically encounter the same error again until more storage space is available. You can remove or compress some of the log files. See Chapter 14 "Support Tools and Advanced Concepts" for additional information. |
RDU-1-103: RDU ran out of memory |
Indicates that the RDU ran out of memory. After encountering this error, the RDU server restarts automatically. |
RDU-1-111: Evaluation key for technology [technology_name] expired |
Indicates that an evaluation key for the technology specified expired. You must contact Cisco sales or TAC for a new license key. |
RDU-1-115: You have used [] percent of available [technology_name] licenses. |
Identifies, in percentage, the quantity of licenses used out of the total number of allowable licenses. Appears when you reach 80 percent of the license capacity. |
RDU-1-122: DNS took [] seconds for lookup of address [ip/hostname]. Check DNS configuration and health of servers |
Indicates that Cisco BAC performance may be slow due to delayed response from the DNS. The alert is generated whenever IP address lookup takes more than 60 seconds. |
RDU-2-119: Directory [] that contains the RDU database has a filesystem block size of [] bytes that does not match the required size of [] bytes. Corruption may occur. |
Indicates that the Cisco BAC database may not be reliable because the file system that contains the database files is not configured to support an 8-KB or greater block size. For details on configuring the file-system block size, see the Installation and Setup Guide for the Cisco Broadband Access Center 4.1. |
RDU-2-200: Directory [] that contains the RDU database transaction logs has a filesystem block size of [] bytes that does not match the required size of [] bytes. Corruption may occur. |
Indicates that the Cisco BAC database may not be reliable because the file system that contains the database log files is not configured to support an 8-KB or greater block size. For details on configuring the file system block size, see the Installation and Setup Guide for the Cisco Broadband Access Center 4.1. |
Note Whenever an RDU syslog alert is sent, additional details (if any) can be found in the log file BPR_DATA/rdu/logs/rdu.log. |
DPE Alerts
Whenever a DPE syslog alert is sent, you can find additional details in the DPE logs.
You can use the show log command to access the DPE logs. For additional information, see the Cisco Broadband Access Center DPE CLI Reference 4.1.
Some DPE errors are also propagated to the RDU server log files. You can find these in the BPR_DATA/rdu/logs/rdu.log file.
Table A-3 identifies the DPE alerts.
Table A-3 DPE Alerts
|
|
DPE-1-102: DPE ran out of disk space |
The storage partition that the DPE server uses ran out of space. You have three options: a. Clear out any excess support bundles that may reside on the disk. You can do this by moving those support bundles to another machine and then running the clear bundles command from the DPE command-line interface (CLI). b. Run the clear logs command from the DPE CLI to clear more disk space. c. As a last resort, run the clear cache command from the DPE CLI to remove any cache files and force the DPE to resynchronize with the RDU server. |
DPE-1-104: DPE ran out of memory |
The DPE process ran out of memory. After encountering this error condition, the DPE restarts automatically. Determine how many device configurations are on the DPE; the larger the number of device configurations, the more memory is used. To reduce the number of device configurations, limit the number of devices in the provisioning groups, either primary or secondary, that the DPE serves. |
DPE-1-109: Failed to connect to RDU |
The RDU cannot be contacted. You must: a. Verify that the DPE network is configured and connected correctly. b. Check that the DPE is configured to connect to the proper RDU, and that the connecting port is configured properly by using the dpe rdu-server command. c. Check that the RDU process is running on the correct server and listening on the correct port. The DPE attempts to reconnect to the RDU process every few seconds until a connection is established. |
DPE-1-117: DPE license nodes have been exceeded or there is no valid DPE license |
Indicates that the Cisco BAC process watchdog, which starts the DPE, did not detect a license for the DPE. Enter the license key for the DPE using the administrator user interface. If you do not have a license, contact your Cisco representative. |
DPE-1-116: DPE evaluation license has expired. Dropping DPE connections and deleting DPEs from database |
Indicates that an evaluation license key for the DPE expired. You must contact Cisco sales or TAC for a new license key. |
DPE-2-118: Directory [] that contains the DPE's cache has a filesystem block size of [] bytes that does not match the required size of [] bytes. Corruption may occur. |
Indicates that the DPE cache may not be reliable because the file system is not configured to support an 8-KB or greater block size. For details on configuring the file system block size, see the Installation and Setup Guide for the Cisco Broadband Access Center 4.1. |
DPE-1-121: Cannot start the server due to an invalid encryption key. |
Indicates that the DPE could not be started because of an invalid encryption key. |
Watchdog Alerts
Whenever the process watchdog sends a syslog alert, you can find error details (if any) in the BPR_DATA/agent/logs/agent_console.log file and the log files corresponding to the specific component mentioned in the alert (if any). For example, if you receive an alert similar to The rdu unexpectedly terminated, you would check the RDU server log file (BPR_DATA/rdu/logs/rdu.log) for additional information. Table A-4 identifies the process watchdog alerts.
Table A-4 Process Watchdog Alerts
|
|
AGENT-3-9001: Failed to start the [component] |
Indicates that the watchdog has failed to start the specified component. |
AGENT-3-9002: The [component] unexpectedly terminated |
Indicates that the specified component, monitored by the process watchdog, has unexpectedly failed. |
AGENT-6-9004: The [component] has started |
Generated any time a component is successfully started by the process watchdog. This message is for informational purposes only. |
AGENT-6-9005: The [component] has stopped |
Generated any time a component is successfully stopped through the process watchdog. This message is for informational purposes only. |
AGENT-3-9003: Failed to stop the [component] |
Indicates that a component did not stop when the process watchdog attempted to stop it. |
AGENT-3-9003: Failed to create listener thread; [error no]Failed to close listen socket; [error no] Failed to cancel listen thread, and so on |
Indicates errors that are not defined in other alert messages. |
The [component] variable presented in the process watchdog alerts list shown in Table A-4 represents any of these component values:
•rdu
•dpe
•tomcat
•cli
•snmpAgent
•kdc
Network Registrar Extension Point Alerts
Whenever a Cisco BAC Network Registrar extension point syslog alert is sent, you can find additional details in the Network Registrar log file.
Table A-5 identifies the process watchdog alerts.
Table A-5 Network Registrar Extension Alerts
|
|
NR_EP-1-106: Failed to connect to RDU |
The Network Registrar server cannot connect to the RDU. You should verify that the RDU process is running and, if it is not already running, start the RDU. If the RDU is running, use the Network Registrar computer to ping the RDU. If you are unable to ping the RDU, fix the routing tables or other communication parameters, between the two devices. If this alert is frequently repeated, you may have an unstable connection between the two hosts. Use generally accepted network troubleshooting techniques to improve the connectivity between the two hosts. |
NR_EP-1-107: Failed to connect to any DPEs |
The Network Registrar extension cannot connect to the DPEs. Check that there are DPEs in the provisioning group for each Network Registrar extension. If not, change the Network Registrar provisioning group to one that has DPEs available. If DPEs are in the provisioning group, ensure that the Network Registrar extension has registered with the RDU; if it has not, it will not recognize any of the DPEs. If, after completing the check, the alert continues, check that there is network connectivity between the Network Registrar extension and the DPEs in the provisioning group. If this alert is frequently repeated, you may have an unstable connection between the two hosts. Use generally accepted network troubleshooting techniques to improve the connectivity between the two hosts. |
NR_EP-6-108: The Cisco BAC NR extensions have started |
The Network Registrar extensions have been started. |
NR_EP-6-109: The Cisco BAC NR extensions have stopped |
The Network Registrar extensions have been stopped. |
NR_EP-6-110: Registered with RDU [address and port] |
The Network Registrar extensions have been registered with the RDU. The address and port identifies the address of the RDU that has registered the Network Registrar extensions. |
NR_EP-1-111: Failed to find usable (best) DPEs |
The Network Registrar extensions are unable to find a usable DPE. |