Cisco IOS XR System Error Message Reference Guide, Release 4.3.x
Platform Messages
Downloads: This chapterpdf (PDF - 5.05 MB) The complete bookPDF (PDF - 18.29 MB) | Feedback

Table of Contents

Platform Messages

AFMON_EA_OOR Messages

AFMON_EA_VERIFY Messages

AFMON Messages

AHCI Messages

ALPHA_DISPLAY Messages

APIV Messages

ARB Messages

ASM Messages

ASR9k_IFLX Messages

AVSM_APIV Messages

BCM_LOGGER Messages

BCM_SWITCH Messages

BP_SERVER Messages

BPE Messages

BRIDGE Messages

CAIBIST Messages

CANB_SERVER Messages

CARD Messages

CARDMGR Messages

CBC Messages

CCI_HAL_SATORI Messages

CCI_SSTAR Messages

CCTL_ENS Messages

CCTL Messages

CE_SWITCH Messages

CEMGBL Messages

CETHHA Messages

CFP Messages

CGV6_SERVICES Messages

CHP Messages

CIH Messages

CLKCTRL_T Messages

CLKCTRL Messages

CLUSTER_UPGRADE Messages

COMMON Messages

CONCERTO Messages

CPU_CTRL Messages

CPUCTRL_SIP700_DLL Messages

CPUCTRL_SIP700 Messages

CPUCTRL Messages

CPUCTRLLIB Messages

CROSSBAR Messages

DC_SERVICE_SRVR Messages

DIAGS Messages

DISCOVERY Messages

DISK_DRIVER Messages

DISKCAM Messages

DMAC Messages

DRP_PAIRING_CLIENT Messages

DRP_PAIRING Messages

DSC_CTRL Messages

DSC Messages

DSCMEDIA Messages

EIO Messages

EMUX Messages

ENV_AGT_DLL Messages

ENVMON_MON Messages

ENVMON Messages

EOBC Messages

ETH_SRVR_API Messages

ETH_SRVR Messages

ETHER_CTRL_DLL Messages

ETHER_CTRL Messages

FABARBITER Messages

FABIO Messages

FABMGR Messages

FABRIC_CTRL Messages

FAN Messages

FAULT_MGR_CLIENT Messages

FAULT_MGR_EH Messages

FAULT_MGR Messages

FAULT Messages

FCA Messages

FDIAGS Messages

FFQ Messages

FIB_DBG Messages

FIB_IDB_LIB Messages

FIB_LTRACE Messages

FPD_BURNER Messages

FPGAMGR Messages

FSYNC Messages

G_PLIM_QOS Messages

GE_DMAC Messages

GSR_FIB_STATS_API Messages

GSR_IPV4_EA Messages

GSR_IPv6_EA Messages

GSR_lc_exmem Messages

GSR_LC_PM Messages

GSR_LIB Messages

GSR_MPLS_EA Messages

GSR_PRP_PM Messages

GSR_TUNNEL_EA Messages

GT_I2C Messages

HAL_COMM_DBG Messages

HBAGENT Messages

HD Messages

HFR_IP_EA Messages

HFR_IPV6_EA Messages

HFR_L2FIB_METRO_SHOW Messages

HFR_LCPM_SHOW Messages

HFR_MPLS_EA Messages

HFR_PM_CS Messages

HFR_PM_SHOW Messages

HFR_PM_TEST Messages

HFR_PM Messages

HFR_SPP Messages

HFR_TUNNEL_EA Messages

HORSE Messages

HPI Messages

hytop Messages

I2C_DRV Messages

I2C_MASTERSHIP Messages

I2C Messages

I2CCTRL Messages

ILITE Messages

IMUX Messages

INTCTRL Messages

INTEG_SWITCH Messages

INV_AGENT Messages

INV Messages

INVMGR Messages

IPCP_SRVR Messages

JBI Messages

KD Messages

L2FIB_ALARM Messages

LAMPTEST Messages

LC_CPIDB Messages

LC_CPPIF Messages

LC_CPUCTRL Messages

LC_FPGA_UPGRADE Messages

LC_PIDB Messages

LC_QFPCPUCTRL Messages

LDA Messages

LIB_ISOLATION Messages

libpcmcia_ide Messages

libpcmcia_linux Messages

LIC_UDI Messages

MACE Messages

MANSDORF Messages

MBI_HELLO Messages

MBI_LIB_ACCESS Messages

MBI_LIB Messages

MBIMGR Messages

MBUS Messages

MCE Messages

MCU Messages

MDIO Messages

MGID_ERROR Messages

MGID_OOR Messages

MGID_PROTECTED_FABRIC Messages

MLAN Messages

MLRMGR Messages

MPC8641 Messages

MSM Messages

NFEA_HW_PROG Messages

NFEA_PAL Messages

NIRVANA Messages

NP Messages

NPUXBAR_BRIDGE Messages

NVEDGE_DATA Messages

OBFL_PD Messages

OBFL Messages

obfl Messages

OBFL Messages

obfl Messages

OBFL Messages

obfl Messages

OBFL Messages

obfl Messages

OBFL Messages

obfl Messages

OIRD Messages

P40X0_DPAA Messages

PBR_EA_OOR Messages

PBR_EA_VERIFY Messages

PCIE_CLIENT Messages

PCIE_HAL Messages

PCIE_SWITCH Messages

PCIE Messages

PCIER Messages

PCIMGR Messages

PCMCIA Messages

PCMCIAD Messages

PCTL Messages

PDMA_SPP Messages

PEX Messages

PEX8111 Messages

PEX8508 Messages

PEXMGR Messages

PEXRC Messages

PFM Messages

PLAT_BMADJ Messages

PLAT_FIB_EA Messages

PLAT_FIB_ECD Messages

PLAT_FIB_GTRIE Messages

PLAT_FIB_HAL Messages

PLAT_FIB_MPLS Messages

PLAT_FIB_RP Messages

PLAT_FIB Messages

PLAT_ICPE_EA_DEBUG Messages

PLAT_ICPE_EA_LTRACE Messages

PLAT_ICPE_EA Messages

PLAT_L2FIB_ATOM Messages

PLAT_L2FIB_BRIDGING Messages

PLAT_L2FIB_COMMON Messages

PLAT_L2FIB_DEBUG Messages

PLAT_L2FIB_L2TP Messages

PLAT_L2FIB_LOCSW Messages

PLAT_L2FIB_LTRACE Messages

PLAT_L2FIB_MAC_CACHE Messages

PLAT_L2FIB_METRO Messages

PLAT_L2FIB_POGO Messages

PLAT_L2FIB_RP Messages

PLAT_L2FIB_SNOOP Messages

PLAT_L2FIB_VPLS Messages

PLAT_L2FIB Messages

PLAT_L2VPN_DEBUG Messages

PLAT_L2VPN_FGID Messages

PLAT_L2VPN_LTRACE Messages

PLAT_L2VPN Messages

PLAT_MCAST Messages

PLAT_THOR_L2FIB_ATOM Messages

PLAT_THOR_L2FIB_DEBUG Messages

PLAT_THOR_L2FIB_LOCSW Messages

PLAT_THOR_L2FIB_LTRACE Messages

PLAT_THOR_L2FIB_MLD Messages

PLAT_THOR_L2FIB_VPLS Messages

PLAT_THOR_L2FIB Messages

PLAT_UDI_MGR Messages

PLAT_V6FIB_RP Messages

PLATFORM_ASR9K_LIB Messages

PLATFORM_HFR_LIB Messages

PLDMGR Messages

PLIM_16P_OC48 Messages

PLIM_IPC Messages

PLIM_SERVICES Messages

PLIM_UPGRADE_FPD Messages

PLU Messages

PLUTLU Messages

PM_OS Messages

PORT_CFG Messages

POWERMGR Messages

preroute Messages

PRM_VERIFY Messages

PRM Messages

PROCMGR_DLL Messages

PROCMGR Messages

PRP_HW Messages

PRP3_FABIO Messages

PRP3_SLR_FABIO Messages

PSARB Messages

PSARBLC Messages

PUNT_INFRA Messages

PUNT_SWITCH Messages

PUNT Messages

PWHE_EA_PD Messages

PWR_MGMT Messages

PWR_SUPPLY Messages

PWRMON Messages

QFPCPUBridgeFPGA Messages

QOSHAL Messages

QSFP_PLUS Messages

RCCLIB Messages

REDDRV Messages

REEP Messages

ROM_UPGRADE_LIB Messages

ROMMON_BURNER Messages

RSP_CPUCTRL Messages

RUNA Messages

RWMGR Messages

SATORI Messages

SCC Messages

SCF Messages

SE_P2MP_SRVR Messages

SERDES Messages

SERVICE_AGENT Messages

SFP Messages

SHELFMGR_API Messages

SHELFMGR_HAL Messages

SHELFMGR Messages

SHELFMGRV2 Messages

SHOW_VERSION_CMD Messages

SIM_INFRA Messages

SIM_IPC Messages

SIM_SE Messages

SL Messages

SMITH Messages

SPA_JBI Messages

SPAN_EA Messages

SPAQFPBridgeCtrl Messages

SPB_I2C Messages

SPENET Messages

SPMCE Messages

SQUID_LOADER Messages

STATE_OUT_OF_SYNC Messages

STP_SHIM Messages

SYSLDR_LC Messages

SYSLDR_RP Messages

SYSLDR Messages

TFQ Messages

TIMESYNC_CLIENT Messages

TIMESYNC Messages

TIPCP Messages

TLU Messages

TOPMGR Messages

TSEC_SPP Messages

TSEC Messages

TUNL_GRE_EA_PD Messages

TUNNEL_GRE_EA Messages

TURBO Messages

UDLD Messages

UPGRADE_FPD Messages

UPGRADE Messages

USB Messages

VCDMA Messages

VIC Messages

VKG_AMCC2035 Messages

VKG_BCM8705 Messages

VKG_CPP_LCPM_SHOW Messages

VKG_CPP_PM_TEST Messages

VKG_CPP_PM Messages

VKG_IP_EA Messages

VKG_IPV4_EA Messages

VKG_IPV6_EA Messages

VKG_LCPM_SHOW Messages

VKG_MPLS_EA Messages

VKG_PM_TEST Messages

VKG_PM Messages

VKG_PMLIB_CLIENT Messages

VKG_PMLIB_IM Messages

VKG_PMLIB Messages

VKG_SERDES Messages

VKG_SIS Messages

WD_PLATFORM Messages

WDMBI Messages

XBAR Messages

XCVR Messages

XFP Messages

ZENJF Messages

ZL Messages

ZPLL_API Messages

Platform Messages

This section contains all Platform related System Error Messages, such as shelf magr, chassis, env ctrl, and so forth.

AFMON_EA_OOR Messages

Error Message %PLATFORM-AFMON_EA_OOR-4-LC_FLOWS_OOR_GREEN

Performance Traffic Monitoring: [chars] flow count on LC no longer at maximum capacity

Explanation Performance traffic monitoring has cleared an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on an LC is no longer at maximum.

Recommended Action None

Error Message %PLATFORM-AFMON_EA_OOR-4-LC_FLOWS_OOR_RED

Performance Traffic Monitoring: [chars] flow count reached maximum ([unsigned int]) on LC

Explanation Performance traffic monitoring has encountered an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on a LC has reached maximum capacity. New flows will no longer be learnt

Recommended Action Reduce the number of flows being monitored on the NP. This can be done by 1) Modifying ACL: (a) Remove the performance traffic service policy from the interface (b) Modify the ACL used in the service policy to be more specific to match a smaller set of flows to be monitored (c) Reapply the service policy to the interface

Error Message %PLATFORM-AFMON_EA_OOR-4-NP_FLOWS_OOR_GREEN

Performance Traffic Monitoring: [chars] flow count on NP [unsigned int] no longer at maximum capacity

Explanation Performance traffic monitoring has cleared an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on a NP is no longer at maximum.

Recommended Action None

Error Message %PLATFORM-AFMON_EA_OOR-4-NP_FLOWS_OOR_GREEN

Performance Traffic Monitoring: Monitored flows on LC [unsigned int] no longer at maximum capacity

Explanation Performance traffic monitoring has cleared an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on a LC is no longer at maximum.

Recommended Action None

Error Message %PLATFORM-AFMON_EA_OOR-4-NP_FLOWS_OOR_RED

Performance Traffic Monitoring: [chars] flow count reached maximum ([unsigned int]) on NP [unsigned int]

Explanation Performance traffic monitoring has encountered an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on a NP has reached maximum capacity. New flows will no longer be learnt

Recommended Action Reduce the number of flows being monitored on the NP. This can be done by 1) Modifying ACL: (a) Remove the performance traffic service policy from the interface (b) Modify the ACL used in the service policy to be more specific to match a smaller set of flows to be monitored (c) Reapply the service policy to the interface 2) Moving monitored flows to a different interface on a different NP

Error Message %PLATFORM-AFMON_EA_OOR-4-NP_FLOWS_OOR_RED

Performance Traffic Monitoring: Maximum monitored flows ([unsigned int]) reached on LC [unsigned int]

Explanation Performance traffic monitoring has encountered an out-of-resource condition. Performance traffic monitoring process on the linecard has detected that the number of flows being monitored on a LC has reached maximum capacity. New flows will no longer be learnt

Recommended Action Reduce the number of flows being monitored on the LC. This can be done by 1) Modifying ACL: (a) Remove the performance traffic service policy from the interface (b) Modify the ACL used in the service policy to be more specific to match a smaller set of flows to be monitored (c) Reapply the service policy to the interface 2) Moving monitored flows to a different interface on a different LC

AFMON_EA_VERIFY Messages

Error Message %PLATFORM-AFMON_EA_VERIFY-6-POLICY_ERROR

Performance traffic service policy verification failed, error [chars]: [chars]

Explanation Peformance traffic service policy verification encountered the specified error

Recommended Action Correct the performance traffic service policy

Error Message %PLATFORM-AFMON_EA_VERIFY-6-POLICY_ERROR

Performance traffic service policy verification failed, error [chars]: [chars]

Explanation Peformance traffic service policy verification encountered the specified error

Recommended Action Correct the performance traffic service policy

AFMON Messages

Error Message %PLATFORM-AFMON-3-AVL_TREE_CORRUPT

Corruption detected in AVL tree for [chars]

Explanation During restart, corruption was detected in the AVL tree. Tree is reinitialized as part of recovery, some interval history during this time could be lost for the flow

Recommended Action No action is required if it is flow tree. Process will try to recover by recreating the tree. In case of interface tree, remove all the policy config on the LC. If that fail, reload the LC If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-EA_DEBUG_INIT_FAIL

Failed to initialise debug infra within AFMon EA. Error: [chars]

Explanation Debug initialization failed within EA. Debugs may not be printed

Recommended Action No action is required. Process will be automatically restarted.

Error Message %PLATFORM-AFMON-3-EA_LTRACE_INIT_FAIL

Failed to initialise ltrace infra within AFMon EA. Error [chars]

Explanation Ltrace initialization failed within EA. Ltraces may not be printed

Recommended Action No action is required. Process will be automatically restarted.

Error Message %PLATFORM-AFMON-3-EA_POL_MOD_ROLLBACK_FAIL

Error encountered during Rollback phase of policy modification on interface: [chars] (ifh: [hex]), Error: [chars]

Explanation AFMon EA encountered an error during rollback phase of policy modification on an interface. In this condition, h/w programming of the policy may not be in sync with policy configuration.

Recommended Action Remove the Vidmon policy on the interface for which the this error message is printed and then re-apply the policy

Error Message %PLATFORM-AFMON-3-ERR_EVENT_ATTACH

Failed to attach event to event manager: [chars]

Explanation Failed to attach event to event manager.

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-ERR_EVENT_INIT

Failed to initialize event manager event: [chars]

Explanation Failed to initialize event manager event.

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-ERR_EVM_CREATE

Failed to setup event manager

Explanation Failed to setup event manager.

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-FAM_CONNECT_FAIL

FAM connection failed - [chars]

Explanation Connection to FAM process failed during AFMon EA process init. This would lead to an inablility of AFMon EA to receive flow updates from the hardware

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-IM_CONNECT_FAIL

Server connection failed - [chars]. Error code - [chars]

Explanation Connection to IM server failed during AFMon EA process init. This would lead to an inablility of AFMon EA to process CAPS from AFMon MA and to a potential disconnect between the hardware/software views of the configured afmon policies on the system.

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-3-MAX_FLOW_LIMIT

LC has reached maximum limit for flows, current [dec] maximum allowed [dec]

Explanation Software enforces a limit of 1.5 times the maximum number of flows permitted on a LC. When this limit is reached, no more new flows can be added unless the current flow count comes under the limit

Recommended Action Reduce the number of flows in the LC If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

Error Message %PLATFORM-AFMON-4-ERR_EVM_EVENT_BLOCK

Unrecoverable error in event loop. Error: [chars]

Explanation An error (other than EINTR) occured in the event loop. The process has exited and restarted.

Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*

AHCI Messages

Error Message %PLATFORM-AHCI-2-DEV_HD0_NOT_RESPONDING

HD0 device not responding

Explanation SATA HD0 device not responding

Recommended Action Please attempt the following: If dual RSP, and the problem is on the active RSP, issue ’redundancy switchover’ If the problem is on the standby/simplex RSP: Restart low level ahci driver via ksh, ’process restart devb-ahci’ Failing which, Reload RSP If problem persists, SATA HD0 devices have to be replaced If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-AHCI-2-DEV_HD1_NOT_RESPONDING

HD1 device not responding

Explanation SATA HD1 device not responding

Recommended Action Please attempt the following: If dual RSP, and the problem is on the active RSP, issue ’redundancy switchover’ If the problem is on the standby/simplex RSP: Restart low level ahci driver via ksh, ’process restart devb-ahci’ Failing which, Reload RSP If problem persists, SATA HD1 devices have to be replaced If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ALPHA_DISPLAY Messages

Error Message %PLATFORM-ALPHA_DISPLAY-3-INIT_ERROR

Process Initialization Failed: ([chars]%s)

Explanation The alphadisplay process failed to initialize. The alphadisplay process controls the 8 characters alphanumeric LEDs on the bottom of all 12000 series line and route processor cards (excluding SIP cards). It provides for the configuration of custom messages as well as the reading of the current output both through CLI and XML. %s - indicates the reason for the failure. There are 2 types of possible failures, these include: - Event Manager Creation Failure - SYSDB Initialization Failure %s - is the decoded error reason

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute ’show process alphadisplay’ to verify that the process is up and running. If it is still non-operational, try doing try doing ’process restart alphadisplay’ If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ALPHA_DISPLAY-6-CHANGE

Alpha display on node [chars] changed to [chars] in state [chars]

Explanation Message to indicate that alpha-display was updated with new string or state.

Recommended Action None.

Error Message %PLATFORM-ALPHA_DISPLAY-6-CHANGE

Alpha display on node [chars] changed to [chars] in state [chars]

Explanation Message to indicate that alpha-display was updated with new string or state.

Recommended Action *None*

Error Message %PLATFORM-ALPHA_DISPLAY-6-CHANGE

Alpha display on node [chars] changed to [chars] in state [chars]

Explanation Message to indicate that alpha-display was updated with new string or state.

Recommended Action None.

Error Message %PLATFORM-ALPHA_DISPLAY-7-EVENT_ERROR

Event Failure: ([chars])

Explanation The alphadisplay process received a bad event. The alphadisplay process controls the 8 characters alphanumeric LEDs on the bottom of all 12000 series line and route processor cards (excluding SIP cards). It provides for the configuration of custom messages as well as the reading of the current output both through CLI and XML. %s - is the decoded error reason

Recommended Action Monitor the event messages. The alphadisplay process will handle the failure gracefully but if they continually appear on the console, try doing ’process restart alphadisplay’ If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

APIV Messages

Error Message %PLATFORM-APIV-3-MODULE_INCOMPATIBLE

APIV module [chars] is incompatible

Explanation APIV module version negotiation failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-APIV-3-SW_ERROR

[chars]

Explanation An internal software error has occurred for the specified APIV module

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-APIV-5-API_INCOMPATIBLE

Message [dec] in APIV module [chars] is incompatible (reason: [chars])

Explanation The APIV module message version negotiation failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ARB Messages

Error Message %PLATFORM-ARB-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation Arbiter driver encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation Arbiter driver encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Arbiter driver encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Arbiter driver encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the arbiter driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the arbiter driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation Arbiter driver Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation Arbiter driver Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation Arbiter driver Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation Arbiter driver Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in arbiter driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in arbiter driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation Arbiter driver Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation Arbiter driver Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation Arbiter driver LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ARB-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation Arbiter driver LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

ASM Messages

Error Message %PLATFORM-ASM-0-FAULT_RECOVERY_ERR

The fault recovery procedure for the FromFab component of the fabric driver has failed. The root fault was: [chars]

Explanation When a hardware fault occurs and the device driver cannot correct it, the Platform Manager is required to reset the ASICs. This error indicates that the Platform Manager failed to reset the ASICs and the hardware on the PRP may not be in an operational state. This condition affects the functionality of the entire router. %s is the Interrupt Source.

Recommended Action If the system has not failed over automatically and a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0 ’ where x is the slot of route processor that generated the error. If no redundant RP is configured you will need to reboot the router by issuing the reload command. Call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-0-SW_INIT_ERR

A software error occurred in the FrFab driver component during initialization: [chars]

Explanation The fabricq_prp_driver process which controls the FromFab driver on the route processor has failed to initalize and cannot recover automatically. This is a software fault. The FromFab driver controls the hardware that receives data from the fabric. It runs in the fabricq_prp_driver process. An unrecoverable failure of the fabricq_prp_driver process may prevent this route processor card from communicating with other cards on the chassis. %s indicates the type failure

Recommended Action Restart the fabricq_prp_driver process with the following command: ’process restart fabricq_prp_driver’ If the error message appears again, then: if a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0 ’ where x is the slot of route processor that generated the error. if no redundant RP is configured you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-BADDESC_ERR

Assembler detected a bad descriptor error: Data [hex]

Explanation Assembler detected a bad descriptor in the free queue. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-CRC_ERR

assembler dll: block: [chars], entity: [chars] had CRC error, count: [dec]

Explanation PII block got a packet from the entity mentioned above with a CRC error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-DEVICE_HALT

FFQ: device halted, sub-block: [chars], halted entity: [chars]

Explanation FFQ, ASIC got halted. The halted block and its parent block are provided

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FATAL

assembler dll: fatal error encountered, reason equals [chars]

Explanation iqm, assembler dll manager encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FATAL_2

assembler dll: fatal error encountered, reason equals [chars], errno equals [dec]

Explanation assembler encountered a fatal error and is not able to recover from the error. A reason text will be supplied call support with this text. An integer errno will also be printed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FIA_INTFERR

Assembler detected a FIA interface error: Data [hex]

Explanation Assembler detected an error with the fia interface. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FIA_PARITYERR

Assembler detected a FIA parity error: Data [hex]

Explanation A parity error has been detected on the assembler to fia interface. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FQEMPTY_ERR

Assembler detected that a free queue is empty

Explanation The assembler component has detected that one of the free queues used to buffer packets coming from the fabric into the route processor is empty.

Recommended Action The system will most likely recover from this error automatically. No intervention is required. If this error is reported frequently you may want to call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-FQEMPTY_ERR

Assembler detected a free queue empty error: Data [hex]

Explanation Assembler detected a that the free queue is empty. The hex number indicates the error cause register value.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-GEN_INFO

assembler dll: general information,[chars]

Explanation The ASM’s informational message.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-HWINIT_INCOMPLETE

assembler dll: hardware initialization not complete

Explanation hardware init is not complete.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-INFO

assembler dll: service degrading error, reason equals [chars]

Explanation The assembler encountered an error that would lead to degraded service.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-INTR_ENABLE_FAIL

assembler dll: intr enable at addr: [hex] mask: [hex] failed.

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-INTR_STATUS_GET_ERR

assembler dll: intr status get failed for: [chars]@[hex], rc equals [dec]

Explanation Hardware register read failed.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-MALLOC_FAILED

assembler dll: fatal memory allocation error for [dec] bytes

Explanation ASM encountered a fatal memory allocation error

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-NOT_AVAILABLE

assembler dll: asic is not available

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-NOT_OPERATIONAL

assembler dll: asic is not operational, state: [dec]

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-3-NOT_YET_IMPLEMENTED

assembler dll: this function [chars] is not yet implemented

Explanation FFQ, assembler dll, a function is not implemented.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-3-RESET_ERR

Assembler is being reset because of too many errors.

Explanation Assembler software driver is seeing too many errors that indicated a problem with the hardware. Some of the error logs prior to this message should indicate the errors that lead to this reset.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-4-BADDESC_ERR

Assembler detected a bad descriptor.

Explanation Assembler detected a bad descriptor in the free queue. The system will usually recover from this error automatically. If the frequency of this alert increases noticeably it could indicate a hardware problem on the route processor card.

Recommended Action The system will normally recover from this error without intervention. If the frequency with which this error occurs increases substantially, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-ASM-6-UNHANDLED_HALT

assembler dll: halt not handled, parent: [chars], child: [chars], intr: [dec]

Explanation Hardware halt is not handled.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-ASM-6-UNHANDLED_INTR

assembler dll: intr not handled, parent: [chars], child: [chars], group id: [dec], intr: [dec]

Explanation Hardware interrupt is not handled in the code, need to implement.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

ASR9k_IFLX Messages

Error Message %PLATFORM-ASR9k_IFLX-5-FRONT_PORT_SHARING_WARNING

PLATFORM-IFLX: [chars]

Explanation Only 10/100M IFLX front port sharing mode is supported. No explicit blocking

Recommended Action Do not config unsupported IFLX front port sharing mode

AVSM_APIV Messages

Error Message %PLATFORM-AVSM_APIV-3-REGISTRATION_TIMEOUT

Timeout ([dec] seconds) waiting for APIV modules registration.

Explanation The registration of APIV modules has not completed. The specified timeout period has reached and is this event will be considered as a failure that will trigger a reload of the affected card.

Recommended Action Contact Cisco TAC to diagnose the problem.

Error Message %PLATFORM-AVSM_APIV-4-MOD_NOT_REGISTERED

The [chars] APIV module (module ID equals [dec]) was not registered in time to receive version negotiation event notification.

Explanation This event will cause the module to fail in APIV versioning negotiation operation.

Recommended Action Contact Cisco TAC to diagnose the problem.

BCM_LOGGER Messages

Error Message %PLATFORM-BCM_LOGGER-6-LOGGING_DEVICE

Node: [chars]: [chars] will be used for storing control ethernet logs. Current logs are under [chars] directory.

Explanation This is an informational message to indicate the location of for es_persist, bcm.log, stp.log and stp_shim.log are.

Recommended Action Do nothing

Error Message %PLATFORM-BCM_LOGGER-7-COPY_FAILED

Copying of log file to [chars] failed. err equals [dec], status equals [dec]. Restarting to recover.

Explanation This is an informational message to indicate that copying a log file to the storage device indicated has failed. This could be because the device was being formatted. The process will restart to recover.

Recommended Action Do nothing

Error Message %PLATFORM-BCM_LOGGER-7-DIR_NOT_FOUND

[chars] directory not found.

Explanation This is an informational message to indicate that a log directory in the storage device is not found. This could be because the device was being formatted. The process will restart to recover.

Recommended Action Do nothing

Error Message %PLATFORM-BCM_LOGGER-7-NO_STORAGE_DEVICE_FOUND

Copying of control-ethernet log files to persistent storage is suspended because no persistent storage device (harddisk/PCMCIA disk) found

Explanation The service that copies /tmp/bcm.log, stp.log, es_persist to persistent storage, did not find any of harddisk, disk0, disk1 available

Recommended Action See if any of harddisk, disk0, disk1 are accessible on the RP. If they are accessible, restart bcm_logger.

BCM_SWITCH Messages

Error Message %PLATFORM-BCM_SWITCH-2-LINK_SHUT_DOWN

Spanning Tree Port [chars] state changed to ADMIN_DOWN

Explanation Spanning Tree Port’s state change by manual intervention.

Recommended Action No action is required.

Error Message %PLATFORM-BCM_SWITCH-2-LINK_STATE_CHANGE

Spanning Tree Port [chars] state changed to [chars]

Explanation Spanning Tree Port’s state change indication.

Recommended Action No action is required.

Error Message %PLATFORM-BCM_SWITCH-2-MMU_ERR

Control Ethernet Intra-rack Switch [dec] detected MMU error

Explanation The switch encountered a MMU error. MMU errors can affect traffic forwarding in the switch.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BCM_SWITCH-2-PCI_ERR

PCI fatal error seen on switch [dec] DMA channel [dec] type [chars]

Explanation The switch encountered a PCI error during a DMA transaction.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BCM_SWITCH-6-GBP_FULL

Control Ethernet Intra-rack Switch [dec] detected Memory full condition

Explanation The switch encountered a memory full condition. Normally this error is not expected. As per the spec, this situation should fix itself. The ports will drop packets in ingress if the situation persists.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

BP_SERVER Messages

Error Message %PLATFORM-BP_SERVER-3-ERR_DSC_ELECTION

This RP detected more than 2 RPs (active/standby) inserted in the chassis.

Explanation When more than 2 RPs (active/standby) are used in the same chassis, one must be elected as the dSC, the master of the chassis. In order to select which RP will become the dSC, insert only the RPs that will be part of the Owner Logical Router (maximum of 2 RPs). Once these RPs are fully booted, you may insert other RPs as required and assign them to manage logical routers. At this point, chassis mastership has been determined and subsequent power-cycle of the chassis will support multiple RPs with no problem.

Recommended Action Eject RPs that are unused or not in the Owner Logical Router. Ensure there are no more than 2 RPs inserted. Reload the RPs. Wait for console prompt. Insert other RP cards and load them as required.

Error Message %PLATFORM-BP_SERVER-3-ERR_INIT_DSC

Failed to learn if we are running on the DSC ([chars])

Explanation This process needs to know if it runs on the DSC or standby DSC. An error occured while trying to get the information from the DSC process. The process will voluntary exit, and should be restarted.

Recommended Action Verify that the DSC process is running using ’show process’ command.

Error Message %PLATFORM-BP_SERVER-3-ERR_MAC_BLK_SIZE

Backplane NVRAM contains MAC address info field [hex] which is invalid. Please rectify this problem to ensure quality operation of your router

Explanation There is a MAC address block field in the backplane NVRAM. If the MAC address block field is invalid, there is the possibility of corrupted backplane NVRAM or incompatibility with the software

Recommended Action Verify that the chassis is supported with the version of software. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message %PLATFORM-BP_SERVER-3-INVALID_BP_VERSION

Backplane NVRAM contains Backplane Version number [dec] which is invalid. Please rectify this problem to ensure quality operation of your router

Explanation There is a Backplane Version field in the backplane NVRAM. If the Backplane Version field is invalid, there is the possibility of corrupted backplane NVRAM or incompatibility with the software

Recommended Action Verify that the chassis is supported with the version of software. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message %PLATFORM-BP_SERVER-3-INVALID_CHASSIS_MODEL

Backplane NVRAM contains chassis model number [dec] which is invalid. Please rectify this problem to ensure quality operation of your router

Explanation Backplane NVRAM contains the chassis model number which the software relies on for chassis identification. This is a complaint about an invalid chassis model number is stored in backplane NVRAM. Software will try its best to use the CSC card in the chassis to determine the chassis model.

Recommended Action Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

BPE Messages

Error Message %PLATFORM-BPE-3-ERR

[chars], [chars]([hex])

Explanation An error occurred in BPE Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation BPE Driver encountered a fatal error and is not able to recover. The supplied text string will explain the reason. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation BPE encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the bpe_driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-5-INFO

[chars]

Explanation This message logs an informational message.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-DEBUG_CONT

Continuing execution: [chars]

Explanation This message indicates an condition occurred beyond which execution of the bpe_driver may continue

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation BPE Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation BPE Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in BPE Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation BPE Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BPE-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation bpe LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

BRIDGE Messages

Error Message %PLATFORM-BRIDGE-1-DDR_BUS_BIT_STUCK_0

DDR bus data bit stuck-0

Explanation DDR bus databit stuck on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_BUS_BIT_STUCK_1

DDR bus data bit stuck-1

Explanation DDR bus databit stuck on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_BUS_BIT_STUCK_2

DDR bus data bit stuck-2

Explanation DDR bus databit stuck on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_BUS_BIT_STUCK_3

DDR bus data bit stuck-3

Explanation DDR bus databit stuck on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_LOSS_OF_SYNC_0

DDR interface loss of sync-0

Explanation Loss of sync on DDR interface on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_LOSS_OF_SYNC_1

DDR interface loss of sync-1

Explanation Loss of sync on DDR interface on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_LOSS_OF_SYNC_2

DDR interface loss of sync-2

Explanation Loss of sync on DDR interface on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-DDR_LOSS_OF_SYNC_3

DDR interface loss of sync-3

Explanation Loss of sync on DDR interface on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_FIA2BR_0

FIFO-0 FIA to bridge-0 overflow

Explanation FIFO-0 FIA to bridge instance-0 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_FIA2BR_1

FIFO-0 FIA to bridge-1 overflow

Explanation FIFO-0 FIA to bridge instance-1 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_FIA2BR_2

FIFO-0 FIA to bridge-2 overflow

Explanation FIFO-0 FIA to bridge instance-2 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_FIA2BR_3

FIFO-0 FIA to bridge-3 overflow

Explanation FIFO-0 FIA to bridge instance-3 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_NPU2BR_0

FIFO-0 NPU to bridge-0 overflow

Explanation FIFO-0 NPU to bridge instance-0 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_NPU2BR_1

FIFO-0 NPU to bridge-1 overflow

Explanation FIFO-0 NPU to bridge instance-1 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_NPU2BR_2

FIFO-0 NPU to bridge-2 overflow

Explanation FIFO-0 NPU to bridge instance-2 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_0_OFLOW_NPU2BR_3

FIFO-0 NPU to bridge-3 overflow

Explanation FIFO-0 NPU to bridge instance-3 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_FIA2BR_0

FIFO-1 FIA to bridge-0 overflow

Explanation FIFO-1 FIA to bridge instance-0 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_FIA2BR_1

FIFO-1 FIA to bridge-1 overflow

Explanation FIFO-1 FIA to bridge instance-1 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_FIA2BR_2

FIFO-1 FIA to bridge-2 overflow

Explanation FIFO-1 FIA to bridge instance-2 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_FIA2BR_3

FIFO-1 FIA to bridge-3 overflow

Explanation FIFO-1 FIA to bridge instance-3 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_NPU2BR_0

FIFO-1 NPU to bridge-0 overflow

Explanation FIFO-1 NPU to bridge instance-0 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_NPU2BR_1

FIFO-1 NPU to bridge-1 overflow

Explanation FIFO-1 NPU to bridge instance-1 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_NPU2BR_2

FIFO-1 NPU to bridge-2 overflow

Explanation FIFO-1 NPU to bridge instance-2 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-FIFO_1_OFLOW_NPU2BR_3

FIFO-1 NPU to bridge-3 overflow

Explanation FIFO-1 NPU to bridge instance-3 overflow.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_0_TX_FIFO_OFLOW_0

MAC on NPU-0 transmit fifo overflow - 0

Explanation MAC on NPU-0 had transmit fifo overflow on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_0_TX_FIFO_OFLOW_1

MAC on NPU-0 transmit fifo overflow - 1

Explanation MAC on NPU-0 had transmit fifo overflow on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_0_TX_FIFO_OFLOW_2

MAC on NPU-0 transmit fifo overflow - 2

Explanation MAC on NPU-0 had transmit fifo overflow on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_0_TX_FIFO_OFLOW_3

MAC on NPU-0 transmit fifo overflow - 3

Explanation MAC on NPU-0 had transmit fifo overflow on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_1_TX_FIFO_OFLOW_0

MAC on NPU-1 transmit fifo overflow - 0

Explanation MAC on NPU-1 had transmit fifo overflow on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_1_TX_FIFO_OFLOW_1

MAC on NPU-1 transmit fifo overflow - 1

Explanation MAC on NPU-1 had transmit fifo overflow on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_1_TX_FIFO_OFLOW_2

MAC on NPU-1 transmit fifo overflow - 2

Explanation MAC on NPU-1 had transmit fifo overflow on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-MAC_1_TX_FIFO_OFLOW_3

MAC on NPU-1 transmit fifo overflow - 3

Explanation MAC on NPU-1 had transmit fifo overflow on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_EGR_Q_ERR_0

NPU-0 egress queue error - 0

Explanation Egress queue error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_EGR_Q_ERR_1

NPU-0 egress queue error - 1

Explanation Egress queue error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_EGR_Q_ERR_2

NPU-0 egress queue error - 2

Explanation Egress queue error on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_EGR_Q_ERR_3

NPU-0 egress queue error - 3

Explanation Egress queue error on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_LOSS_OF_SYNC_0

NPU-0 interface loss of sync-0

Explanation Loss of sync on NPU-0 interface on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_LOSS_OF_SYNC_1

NPU-0 interface loss of sync-1

Explanation Loss of sync on NPU-0 interface on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_LOSS_OF_SYNC_2

NPU-0 interface loss of sync-2

Explanation Loss of sync on NPU-0 interface on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_LOSS_OF_SYNC_3

NPU-0 interface loss of sync-3

Explanation Loss of sync on NPU-0 interface on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_SCH_MEMP_ERR_0

NPU-0 scheduler mem parity error - 0

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_SCH_MEMP_ERR_1

NPU-0 scheduler mem parity error - 1

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_SCH_MEMP_ERR_2

NPU-0 scheduler mem parity error - 2

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_SCH_MEMP_ERR_3

NPU-0 scheduler mem parity error - 3

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_PLL_LOCK_0

NPU-0 XAUI PLL not locked on bridge - 0

Explanation NPU-0 XAUI PLL not locked on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_PLL_LOCK_1

NPU-0 XAUI PLL not locked on bridge - 1

Explanation NPU-0 XAUI PLL not locked on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_PLL_LOCK_2

NPU-0 XAUI PLL not locked on bridge - 2

Explanation NPU-0 XAUI PLL not locked on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_PLL_LOCK_3

NPU-0 XAUI PLL not locked on bridge - 3

Explanation NPU-0 XAUI PLL not locked on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_RDY_0

NPU-0 XAUI not ready on bridge - 0

Explanation NPU-0 XAUI not ready on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_RDY_1

NPU-0 XAUI not ready on bridge - 1

Explanation NPU-0 XAUI not ready on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_RDY_2

NPU-0 XAUI not ready on bridge - 2

Explanation NPU-0 XAUI not ready on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_0_XAUI_RDY_3

NPU-0 XAUI not ready on bridge - 3

Explanation NPU-0 XAUI not ready on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_EGR_Q_ERR_0

NPU-1 egress queue error - 0

Explanation Egress queue error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_EGR_Q_ERR_1

NPU-1 egress queue error - 1

Explanation Egress queue error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_EGR_Q_ERR_2

NPU-1 egress queue error - 2

Explanation Egress queue error on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_EGR_Q_ERR_3

NPU-1 egress queue error - 3

Explanation Egress queue error on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_LOSS_OF_SYNC_0

NPU-1 interface loss of sync-0

Explanation Loss of sync on NPU-1 interface on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_LOSS_OF_SYNC_1

NPU-1 interface loss of sync-1

Explanation Loss of sync on NPU-1 interface on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_LOSS_OF_SYNC_2

NPU-1 interface loss of sync-2

Explanation Loss of sync on NPU-1 interface on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_LOSS_OF_SYNC_3

NPU-1 interface loss of sync-3

Explanation Loss of sync on NPU-1 interface on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_SCH_MEMP_ERR_0

NPU-1 scheduler mem parity error - 0

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_SCH_MEMP_ERR_1

NPU-1 scheduler mem parity error - 1

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_SCH_MEMP_ERR_2

NPU-1 scheduler mem parity error - 2

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_SCH_MEMP_ERR_3

NPU-1 scheduler mem parity error - 3

Explanation Scheduler Hang, Sram or egress mid-fifo parity error on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_PLL_LOCK_0

NPU-1 XAUI PLL not locked on bridge - 0

Explanation NPU-1 XAUI PLL not locked on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_PLL_LOCK_1

NPU-1 XAUI PLL not locked on bridge - 1

Explanation NPU-1 XAUI PLL not locked on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_PLL_LOCK_2

NPU-1 XAUI PLL not locked on bridge - 2

Explanation NPU-1 XAUI PLL not locked on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_PLL_LOCK_3

NPU-1 XAUI PLL not locked on bridge - 3

Explanation NPU-1 XAUI PLL not locked on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_RDY_0

NPU-1 XAUI not ready on bridge - 0

Explanation NPU-1 XAUI not ready on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_RDY_1

NPU-1 XAUI not ready on bridge - 1

Explanation NPU-1 XAUI not ready on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_RDY_2

NPU-1 XAUI not ready on bridge - 2

Explanation NPU-1 XAUI not ready on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-NPU_1_XAUI_RDY_3

NPU-1 XAUI not ready on bridge - 3

Explanation NPU-1 XAUI not ready on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_DATABIT_STUCK_0

QDR memory data bit stuck-0

Explanation QDR memory databit stuck on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_DATABIT_STUCK_1

QDR memory data bit stuck-1

Explanation QDR memory databit stuck on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_DATABIT_STUCK_2

QDR memory data bit stuck-2

Explanation QDR memory databit stuck on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_DATABIT_STUCK_3

QDR memory data bit stuck-3

Explanation QDR memory databit stuck on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_M_FREE_EMPTY_0

Multicast free pages empty - 0

Explanation Multicast free pages empty on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_M_FREE_EMPTY_1

Multicast free pages empty - 1

Explanation Multicast free pages empty on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_M_FREE_EMPTY_2

Multicast free pages empty - 2

Explanation Multicast free pages empty on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_M_FREE_EMPTY_3

Multicast free pages empty - 3

Explanation Multicast free pages empty on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_ECC_FAIL_0

QDR memory ECC failure on bridge-0

Explanation QDR memory ECC failure on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_ECC_FAIL_1

QDR memory ECC failure on bridge-1

Explanation QDR memory ECC failure on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_ECC_FAIL_2

QDR memory ECC failure on bridge-2

Explanation QDR memory ECC failure on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_ECC_FAIL_3

QDR memory ECC failure on bridge-3

Explanation QDR memory ECC failure on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_SELFTEST_FAIL_0

QDR memory self test failure on bridge-0

Explanation QDR memory self test failure on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_SELFTEST_FAIL_1

QDR memory self test failure on bridge-1

Explanation QDR memory self test failure on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_SELFTEST_FAIL_2

QDR memory self test failure on bridge-2

Explanation QDR memory self test failure on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-QDR_MEM_SELFTEST_FAIL_3

QDR memory self test failure on bridge-3

Explanation QDR memory self test failure on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. Please verify the bridge FPGA is loaded properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-REG_ACCESS_FAIL_0

Register access failure on bridge-0

Explanation Register access failure on bridge instance-0.

Recommended Action Please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-REG_ACCESS_FAIL_1

Register access failure on bridge-1

Explanation Register access failure on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-REG_ACCESS_FAIL_2

Register access failure on bridge-2

Explanation Register access failure on bridge instance-2.

Recommended Action Please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-REG_ACCESS_FAIL_3

Register access failure on bridge-3

Explanation Register access failure on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR1_0

State machine-0 error-1 on bridge-0

Explanation State machine - 0 ran into error-1 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR1_1

State machine-0 error-1 on bridge-1

Explanation State machine - 0 ran into error-1 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR1_2

State machine-0 error-1 on bridge-2

Explanation State machine - 0 ran into error-1 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR1_3

State machine-0 error-1 on bridge-3

Explanation State machine - 0 ran into error-1 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR2_0

State machine-0 error-2 on bridge-0

Explanation State machine - 0 ran into error-2 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR2_1

State machine-0 error-2 on bridge-1

Explanation State machine - 0 ran into error-2 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR2_2

State machine-0 error-2 on bridge-2

Explanation State machine - 0 ran into error-2 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR2_3

State machine-0 error-2 on bridge-3

Explanation State machine - 0 ran into error-2 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR3_0

State machine-0 error-3 on bridge-0

Explanation State machine - 0 ran into error-3 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR3_1

State machine-0 error-3 on bridge-1

Explanation State machine - 0 ran into error-3 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR3_2

State machine-0 error-3 on bridge-2

Explanation State machine - 0 ran into error-3 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_0_ERR3_3

State machine-0 error-3 on bridge-3

Explanation State machine - 0 ran into error-3 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR1_0

State machine-1 error-1 on bridge-0

Explanation State machine - 1 ran into error-1 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR1_1

State machine-1 error-1 on bridge-1

Explanation State machine - 1 ran into error-1 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR1_2

State machine-1 error-1 on bridge-2

Explanation State machine - 1 ran into error-1 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR1_3

State machine-1 error-1 on bridge-3

Explanation State machine - 1 ran into error-1 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR2_0

State machine-1 error-2 on bridge-0

Explanation State machine - 1 ran into error-2 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR2_1

State machine-1 error-2 on bridge-1

Explanation State machine - 1 ran into error-2 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR2_2

State machine-1 error-2 on bridge-2

Explanation State machine - 1 ran into error-2 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR2_3

State machine-1 error-2 on bridge-3

Explanation State machine - 1 ran into error-2 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR3_0

State machine-1 error-3 on bridge-0

Explanation State machine - 1 ran into error-3 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR3_1

State machine-1 error-3 on bridge-1

Explanation State machine - 1 ran into error-3 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR3_2

State machine-1 error-3 on bridge-2

Explanation State machine - 1 ran into error-3 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-STATEMC_1_ERR3_3

State machine-1 error-3 on bridge-3

Explanation State machine - 1 ran into error-3 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAN_SYNC_0

XAUI to NPU-0 chan sync error on bridge-0

Explanation XAUI to NPU-0 chan sync error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAN_SYNC_1

XAUI to NPU-0 chan sync error on bridge-1

Explanation XAUI to NPU-0 chan sync error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAN_SYNC_2

XAUI to NPU-0 chan sync error on bridge-2

Explanation XAUI to NPU-0 chan sync error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAN_SYNC_3

XAUI to NPU-0 chan sync error on bridge-3

Explanation XAUI to NPU-0 chan sync error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAR_ALIGN_0

XAUI to NPU-0 char alignment error on bridge-0

Explanation XAUI to NPU-0 char alignment error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAR_ALIGN_1

XAUI to NPU-0 char alignment error on bridge-1

Explanation XAUI to NPU-0 char alignment error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAR_ALIGN_2

XAUI to NPU-0 char alignment error on bridge-2

Explanation XAUI to NPU-0 char alignment error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_CHAR_ALIGN_3

XAUI to NPU-0 char alignment error on bridge-3

Explanation XAUI to NPU-0 char alignment error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_MGT_CV_0

XAUI to NPU-0 MGT code violation on bridge-0

Explanation XAUI to NPU-0 MGT code violation on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_MGT_CV_1

XAUI to NPU-0 MGT code violation on bridge-1

Explanation XAUI to NPU-0 MGT code violation on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_MGT_CV_2

XAUI to NPU-0 MGT code violation on bridge-2

Explanation XAUI to NPU-0 MGT code violation on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_MGT_CV_3

XAUI to NPU-0 MGT code violation on bridge-3

Explanation XAUI to NPU-0 MGT code violation on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_RX_ALIGN_LOSS_0

XAUI to NPU-0 Rx alignment loss - 0

Explanation Rx alignment loss on XAUI to NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_RX_ALIGN_LOSS_1

XAUI to NPU-0 Rx alignment loss - 1

Explanation Rx alignment loss on XAUI to NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_RX_ALIGN_LOSS_2

XAUI to NPU-0 Rx alignment loss - 2

Explanation Rx alignment loss on XAUI to NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_RX_ALIGN_LOSS_3

XAUI to NPU-0 Rx alignment loss - 3

Explanation Rx alignment loss on XAUI to NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_STAT_VEC_0

XAUI to NPU-0 state error on bridge-0

Explanation XAUI to NPU-0 state error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_STAT_VEC_1

XAUI to NPU-0 state error on bridge-1

Explanation XAUI to NPU-0 state error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_STAT_VEC_2

XAUI to NPU-0 state error on bridge-2

Explanation XAUI to NPU-0 state error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_STAT_VEC_3

XAUI to NPU-0 state error on bridge-3

Explanation XAUI to NPU-0 state error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_TX_FIFO_OFLOW_0

XAUI to NPU-0 tx fifo overflow - 0

Explanation XAUI interface to NPU-0 reported tx fifo overflow on bridge instance - 0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_TX_FIFO_OFLOW_1

XAUI to NPU-0 tx fifo overflow - 1

Explanation XAUI interface to NPU-0 reported tx fifo overflow on bridge instance - 1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_TX_FIFO_OFLOW_2

XAUI to NPU-0 tx fifo overflow - 2

Explanation XAUI interface to NPU-0 reported tx fifo overflow on bridge instance - 2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_0_TX_FIFO_OFLOW_3

XAUI to NPU-0 tx fifo overflow - 3

Explanation XAUI interface to NPU-0 reported tx fifo overflow on bridge instance - 3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAN_SYNC_0

XAUI to NPU-1 chan sync error on bridge-0

Explanation XAUI to NPU-1 chan sync error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAN_SYNC_1

XAUI to NPU-1 chan sync error on bridge-1

Explanation XAUI to NPU-1 chan sync error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAN_SYNC_2

XAUI to NPU-1 chan sync error on bridge-2

Explanation XAUI to NPU-1 chan sync error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAN_SYNC_3

XAUI to NPU-1 chan sync error on bridge-3

Explanation XAUI to NPU-1 chan sync error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAR_ALIGN_0

XAUI to NPU-1 char alignment error on bridge-0

Explanation XAUI to NPU-1 char alignment error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAR_ALIGN_1

XAUI to NPU-1 char alignment error on bridge-1

Explanation XAUI to NPU-1 char alignment error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAR_ALIGN_2

XAUI to NPU-1 char alignment error on bridge-2

Explanation XAUI to NPU-1 char alignment error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_CHAR_ALIGN_3

XAUI to NPU-1 char alignment error on bridge-3

Explanation XAUI to NPU-1 char alignment error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_MGT_CV_0

XAUI to NPU-1 MGT code violation on bridge-0

Explanation XAUI to NPU-1 MGT code violation on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_MGT_CV_1

XAUI to NPU-1 MGT code violation on bridge-1

Explanation XAUI to NPU-1 MGT code violation on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_MGT_CV_2

XAUI to NPU-1 MGT code violation on bridge-2

Explanation XAUI to NPU-1 MGT code violation on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_MGT_CV_3

XAUI to NPU-1 MGT code violation on bridge-3

Explanation XAUI to NPU-1 MGT code violation on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_RX_ALIGN_LOSS_0

XAUI to NPU-1 Rx alignment loss - 0

Explanation Rx alignment loss on XAUI to NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_RX_ALIGN_LOSS_1

XAUI to NPU-1 Rx alignment loss - 1

Explanation Rx alignment loss on XAUI to NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_RX_ALIGN_LOSS_2

XAUI to NPU-1 Rx alignment loss - 2

Explanation Rx alignment loss on XAUI to NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_RX_ALIGN_LOSS_3

XAUI to NPU-1 Rx alignment loss - 3

Explanation Rx alignment loss on XAUI to NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_STAT_VEC_0

XAUI to NPU-1 state error on bridge-0

Explanation XAUI to NPU-1 state error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_STAT_VEC_1

XAUI to NPU-1 state error on bridge-1

Explanation XAUI to NPU-1 state error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_STAT_VEC_2

XAUI to NPU-1 state error on bridge-2

Explanation XAUI to NPU-1 state error on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_STAT_VEC_3

XAUI to NPU-1 state error on bridge-3

Explanation XAUI to NPU-1 state error on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_TX_FIFO_OFLOW_0

XAUI to NPU-1 tx fifo overflow - 0

Explanation XAUI interface to NPU-1 reported tx fifo overflow on bridge instance - 0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_TX_FIFO_OFLOW_1

XAUI to NPU-1 tx fifo overflow - 1

Explanation XAUI interface to NPU-1 reported tx fifo overflow on bridge instance - 1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_TX_FIFO_OFLOW_2

XAUI to NPU-1 tx fifo overflow - 2

Explanation XAUI interface to NPU-1 reported tx fifo overflow on bridge instance - 2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_1_TX_FIFO_OFLOW_3

XAUI to NPU-1 tx fifo overflow - 3

Explanation XAUI interface to NPU-1 reported tx fifo overflow on bridge instance - 3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_A_DATABUS_STUCK_0

XAUI-A databus stuck-0

Explanation XAUI-A databus stuck on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_A_DATABUS_STUCK_1

XAUI-A databus stuck-1

Explanation XAUI-A databus stuck on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_A_DATABUS_STUCK_2

XAUI-A databus stuck-2

Explanation XAUI-A databus stuck on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-1-XAUI_A_DATABUS_STUCK_3

XAUI-A databus stuck-3

Explanation XAUI-A databus stuck on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_0_RX_FRAME_ERR_0

MAC on NPU-0 receive frame error - 0

Explanation MAC on NPU-0 received an errored frame interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_0_RX_FRAME_ERR_1

MAC on NPU-0 receive frame error - 1

Explanation MAC on NPU-0 received an errored frame interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_0_RX_FRAME_ERR_2

MAC on NPU-0 receive frame error - 2

Explanation MAC on NPU-0 received an errored frame interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_0_RX_FRAME_ERR_3

MAC on NPU-0 receive frame error - 3

Explanation MAC on NPU-0 received an errored frame interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_1_RX_FRAME_ERR_0

MAC on NPU-1 receive frame error - 0

Explanation MAC on NPU-1 received an errored frame interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_1_RX_FRAME_ERR_1

MAC on NPU-1 receive frame error - 1

Explanation MAC on NPU-1 received an errored frame interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_1_RX_FRAME_ERR_2

MAC on NPU-1 receive frame error - 2

Explanation MAC on NPU-1 received an errored frame interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MAC_1_RX_FRAME_ERR_3

MAC on NPU-1 receive frame error - 3

Explanation MAC on NPU-1 received an errored frame interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MCAST_PAGE_ERR_0

Multicast page error on bridge-0

Explanation Multicast page error on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MCAST_PAGE_ERR_1

Multicast page error on bridge-1

Explanation Multicast page error on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MCAST_PAGE_ERR_2

Multicast page error on bridge-2

Explanation Multicast page error on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-MCAST_PAGE_ERR_3

Multicast page error on bridge-3

Explanation Multicast page error on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_DIP2_ERR_0

NPU-0 egress flow control DIP2 parity error - 0

Explanation Egress flow control DIP2 parity error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_DIP2_ERR_1

NPU-0 egress flow control DIP2 parity error - 1

Explanation Egress flow control DIP2 parity error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_DIP2_ERR_2

NPU-0 egress flow control DIP2 parity error - 2

Explanation Egress flow control DIP2 parity error on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_DIP2_ERR_3

NPU-0 egress flow control DIP2 parity error - 3

Explanation Egress flow control DIP2 parity error on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_OOS_0

NPU-0 egress flow control out-of-sync - 0

Explanation Egress flow control out-of-sync on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_OOS_1

NPU-0 egress flow control out-of-sync - 1

Explanation Egress flow control out-of-sync on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_OOS_2

NPU-0 egress flow control out-of-sync - 2

Explanation Egress flow control out-of-sync on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_0_FC_OOS_3

NPU-0 egress flow control out-of-sync - 3

Explanation Egress flow control out-of-sync on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_DIP2_ERR_0

NPU-1 egress flow control DIP2 parity error - 0

Explanation Egress flow control DIP2 parity error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_DIP2_ERR_1

NPU-1 egress flow control DIP2 parity error - 1

Explanation Egress flow control DIP2 parity error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_DIP2_ERR_2

NPU-1 egress flow control DIP2 parity error - 2

Explanation Egress flow control DIP2 parity error on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_DIP2_ERR_3

NPU-1 egress flow control DIP2 parity error - 3

Explanation Egress flow control DIP2 parity error on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_OOS_0

NPU-1 egress flow control out-of-sync - 0

Explanation Egress flow control out-of-sync on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_OOS_1

NPU-1 egress flow control out-of-sync - 1

Explanation Egress flow control out-of-sync on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_OOS_2

NPU-1 egress flow control out-of-sync - 2

Explanation Egress flow control out-of-sync on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-NPU_1_FC_OOS_3

NPU-1 egress flow control out-of-sync - 3

Explanation Egress flow control out-of-sync on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-QDR_M_WR_ERR_0

Multicast write when free page fifo empty - 0

Explanation Multicast write when free page fifo empty on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-QDR_M_WR_ERR_1

Multicast write when free page fifo empty - 1

Explanation Multicast write when free page fifo empty on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-QDR_M_WR_ERR_2

Multicast write when free page fifo empty - 2

Explanation Multicast write when free page fifo empty on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-2-QDR_M_WR_ERR_3

Multicast write when free page fifo empty - 3

Explanation Multicast write when free page fifo empty on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_0_FIA_0

Checksum error - 0 from FIA on bridge-0

Explanation Checksum error - 0 from FIA on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_0_FIA_1

Checksum error - 0 from FIA on bridge-1

Explanation Checksum error - 0 from FIA on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_0_FIA_2

Checksum error - 0 from FIA on bridge-2

Explanation Checksum error - 0 from FIA on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_0_FIA_3

Checksum error - 0 from FIA on bridge-3

Explanation Checksum error - 0 from FIA on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_1_FIA_0

Checksum error - 1 from FIA on bridge-0

Explanation Checksum error - 1 from FIA on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_1_FIA_1

Checksum error - 1 from FIA on bridge-1

Explanation Checksum error - 1 from FIA on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_1_FIA_2

Checksum error - 1 from FIA on bridge-2

Explanation Checksum error - 1 from FIA on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CHKSUM_ERR_1_FIA_3

Checksum error - 1 from FIA on bridge-3

Explanation Checksum error - 1 from FIA on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_FIA_0

CRC error - 0 from FIA on bridge-0

Explanation CRC error - 0 from FIA on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_FIA_1

CRC error - 0 from FIA on bridge-1

Explanation CRC error - 0 from FIA on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_FIA_2

CRC error - 0 from FIA on bridge-2

Explanation CRC error - 0 from FIA on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_FIA_3

CRC error - 0 from FIA on bridge-3

Explanation CRC error - 0 from FIA on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_NPU_0

CRC error from NPU-0 on bridge-0

Explanation CRC error from NPU-0 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_NPU_1

CRC error from NPU-0 on bridge-1

Explanation CRC error from NPU-0 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_NPU_2

CRC error from NPU-0 on bridge-2

Explanation CRC error from NPU-0 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_0_NPU_3

CRC error from NPU-0 on bridge-3

Explanation CRC error from NPU-0 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_FIA_0

CRC error - 1 from FIA on bridge-0

Explanation CRC error - 1 from FIA on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_FIA_1

CRC error - 1 from FIA on bridge-1

Explanation CRC error - 1 from FIA on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_FIA_2

CRC error - 1 from FIA on bridge-2

Explanation CRC error - 1 from FIA on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_FIA_3

CRC error - 1 from FIA on bridge-3

Explanation CRC error - 1 from FIA on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_NPU_0

CRC error from NPU-1 on bridge-0

Explanation CRC error from NPU-1 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_NPU_1

CRC error from NPU-1 on bridge-1

Explanation CRC error from NPU-1 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_NPU_2

CRC error from NPU-1 on bridge-2

Explanation CRC error from NPU-1 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-CRC_ERR_1_NPU_3

CRC error from NPU-1 on bridge-3

Explanation CRC error from NPU-1 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_CRC_ERR_0

Decoder A CRC Error - 0

Explanation Decoder A CRC error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_CRC_ERR_1

Decoder A CRC Error - 1

Explanation Decoder A CRC error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_FRAME_ERR_0

Decoder A Framing Error - 0

Explanation Decoder A framing error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_FRAME_ERR_1

Decoder A Framing Error - 1

Explanation Decoder A framing error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_PKT_LEN_ERR_0

Decoder A Packet Length Error - 0

Explanation Packet with invalid length encountered by decoder A on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_PKT_LEN_ERR_1

Decoder A Packet Length Error - 1

Explanation Packet with invalid length encountered by decoder A on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_PWM_ERR_0

Decoder A PWM Error - 0

Explanation PWM bit level decoder error on decoder A on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_PWM_ERR_1

Decoder A PWM Error - 1

Explanation PWM bit level decoder error on decoder A on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_TYPE_DISABLED_0

Decode A Type Disabled - 0

Explanation Pkt received for timestamp type disabled on Decoder A on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-DEC_A_TYPE_DISABLED_1

Decode A Type Disabled - 1

Explanation Pkt received for timestamp type disabled on Decoder A on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_LONG_PKT_0_0

Egress long packet detected - 0,0

Explanation Egress long packet detected on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_LONG_PKT_0_1

Egress long packet detected - 0,1

Explanation Egress long packet detected on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_LONG_PKT_1_0

Egress long packet detected - 1,0

Explanation Egress long packet detected on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_LONG_PKT_1_1

Egress long packet detected - 1,1

Explanation Egress long packet detected on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_NPH_LEN_0_0

Egress invalid length detected - 0,0

Explanation Invalid egress NPH length detected on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_NPH_LEN_0_1

Egress invalid length detected - 0,1

Explanation Invalid egress NPH length detected on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_NPH_LEN_1_0

Egress invalid length detected - 1,0

Explanation Invalid egress NPH length detected on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_NPH_LEN_1_1

Egress invalid length detected - 1,1

Explanation Invalid egress NPH length detected on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_DATA_FIFO_OFLOW_0_0

Egress seg data fifo overflow - 0,0

Explanation Egress seg data fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_DATA_FIFO_OFLOW_0_1

Egress seg data fifo overflow - 0,1

Explanation Egress seg data fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_DATA_FIFO_OFLOW_1_0

Egress seg data fifo overflow - 1,0

Explanation Egress seg data fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_DATA_FIFO_OFLOW_1_1

Egress seg data fifo overflow - 1,1

Explanation Egress seg data fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_EXT_FIFO_OFLOW_0_0

Egress seg hdr ext fifo overflow - 0,0

Explanation Egress seg hdr ext fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_EXT_FIFO_OFLOW_0_1

Egress seg hdr ext fifo overflow - 0,1

Explanation Egress seg hdr ext fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_EXT_FIFO_OFLOW_1_0

Egress seg hdr ext fifo overflow - 1,0

Explanation Egress seg hdr ext fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_EXT_FIFO_OFLOW_1_1

Egress seg hdr ext fifo overflow - 1,1

Explanation Egress seg hdr ext fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_FIFO_OFLOW_0_0

Egress seg hdr fifo overflow - 0,0

Explanation Egress seg hdr fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_FIFO_OFLOW_0_1

Egress seg hdr fifo overflow - 0,1

Explanation Egress seg hdr fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_FIFO_OFLOW_1_0

Egress seg hdr fifo overflow - 1,0

Explanation Egress seg hdr fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SEG_HDR_FIFO_OFLOW_1_1

Egress seg hdr fifo overflow - 1,1

Explanation Egress seg hdr fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_FIFO_OFLOW_0_0

Egress sgt fifo overflow - 0,0

Explanation Egress sgt fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_FIFO_OFLOW_0_1

Egress sgt fifo overflow - 0,1

Explanation Egress sgt fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_FIFO_OFLOW_1_0

Egress sgt fifo overflow - 1,0

Explanation Egress sgt fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_FIFO_OFLOW_1_1

Egress sgt fifo overflow - 1,1

Explanation Egress sgt fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_HDR_EXT_FIFO_OFLOW_0_0

Egress sgt hdr ext fifo overflow - 0,0

Explanation Egress sgt hdr ext fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_HDR_EXT_FIFO_OFLOW_0_1

Egress sgt hdr ext fifo overflow - 0,1

Explanation Egress sgt hdr ext fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_HDR_EXT_FIFO_OFLOW_1_0

Egress sgt hdr ext fifo overflow - 1,0

Explanation Egress sgt hdr ext fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT_HDR_EXT_FIFO_OFLOW_1_1

Egress sgt hdr ext fifo overflow - 1,1

Explanation Egress sgt hdr ext fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT2_FIFO_OFLOW_0_0

Egress sgt2 fifo overflow - 0,0

Explanation Egress sgt2 fifo overflow on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT2_FIFO_OFLOW_0_1

Egress sgt2 fifo overflow - 0,1

Explanation Egress sgt2 fifo overflow on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT2_FIFO_OFLOW_1_0

Egress sgt2 fifo overflow - 1,0

Explanation Egress sgt2 fifo overflow on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SGT2_FIFO_OFLOW_1_1

Egress sgt2 fifo overflow - 1,1

Explanation Egress sgt2 fifo overflow on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SP_NOT_ZERO_0_0

Non-zero seg profile detected - 0,0

Explanation Non-zero seg profile detected on xaui-0 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SP_NOT_ZERO_0_1

Non-zero seg profile detected - 0,1

Explanation Non-zero seg profile detected on xaui-0 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SP_NOT_ZERO_1_0

Non-zero seg profile detected - 1,0

Explanation Non-zero seg profile detected on xaui-1 bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-EGR_SP_NOT_ZERO_1_1

Non-zero seg profile detected - 1,1

Explanation Non-zero seg profile detected on xaui-1 bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MAXLEN_ERR_0

FIA to NPU-0 packet maximum length error - 0

Explanation Packet maximum length error on FIA to NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MAXLEN_ERR_1

FIA to NPU-0 packet maximum length error - 1

Explanation Packet maximum length error on FIA to NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MAXLEN_ERR_2

FIA to NPU-0 packet maximum length error - 2

Explanation Packet maximum length error on FIA to NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MAXLEN_ERR_3

FIA to NPU-0 packet maximum length error - 3

Explanation Packet maximum length error on FIA to NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MINLEN_ERR_0

FIA to NPU-0 packet minimum length error - 0

Explanation Packet minimum length error on FIA to NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MINLEN_ERR_1

FIA to NPU-0 packet minimum length error - 1

Explanation Packet minimum length error on FIA to NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MINLEN_ERR_2

FIA to NPU-0 packet minimum length error - 2

Explanation Packet minimum length error on FIA to NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_0_PKT_MINLEN_ERR_3

FIA to NPU-0 packet minimum length error - 3

Explanation Packet minimum length error on FIA to NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MAXLEN_ERR_0

FIA to NPU-1 packet maximum length error - 0

Explanation Packet maximum length error on FIA to NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MAXLEN_ERR_1

FIA to NPU-1 packet maximum length error - 1

Explanation Packet maximum length error on FIA to NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MAXLEN_ERR_2

FIA to NPU-1 packet maximum length error - 2

Explanation Packet maximum length error on FIA to NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MAXLEN_ERR_3

FIA to NPU-1 packet maximum length error - 3

Explanation Packet maximum length error on FIA to NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MINLEN_ERR_0

FIA to NPU-1 packet minimum length error - 0

Explanation Packet minimum length error on FIA to NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MINLEN_ERR_1

FIA to NPU-1 packet minimum length error - 1

Explanation Packet minimum length error on FIA to NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MINLEN_ERR_2

FIA to NPU-1 packet minimum length error - 2

Explanation Packet minimum length error on FIA to NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-FIA2NPU_1_PKT_MINLEN_ERR_3

FIA to NPU-1 packet minimum length error - 3

Explanation Packet minimum length error on FIA to NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_JUMP_ERR_0

GST jump error - 0

Explanation GST jump error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_JUMP_ERR_1

GST jump error - 1

Explanation GST jump error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_PWM_TIMEOUT_0

GST PWM timeout - 0

Explanation GST PWM not received within 1 ms on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_PWM_TIMEOUT_1

GST PWM timeout - 1

Explanation GST PWM not received within 1 ms on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_SYNC_ERR_0

GST SYNC ERR - 0

Explanation GST Sync error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-GST_SYNC_ERR_1

GST SYNC ERR - 1

Explanation GST Sync error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_INV_LEN_0

Ingress invalid length detected - 0

Explanation Invalid ingress NPH length detected on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_INV_LEN_1

Ingress invalid length detected - 1

Explanation Invalid ingress NPH length detected on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_L4_ARRAY_OFLOW_0

Ingress L4 array overflow - 0

Explanation L4 array overflow on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_L4_ARRAY_OFLOW_1

Ingress L4 array overflow - 1

Explanation L4 array overflow on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_L4_ARRAY_UFLOW_0

Ingress L4 array underflow - 0

Explanation L4 array underflow on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-ING_L4_ARRAY_UFLOW_1

Ingress L4 array underflow - 1

Explanation L4 array underflow on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_FIADDR_0

Missing EOP-0 from FIA DDR on bridge-0

Explanation Missing EOP-0 from FIA DDR on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_FIADDR_1

Missing EOP-0 from FIA DDR on bridge-1

Explanation Missing EOP-0 from FIA DDR on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_FIADDR_2

Missing EOP-0 from FIA DDR on bridge-2

Explanation Missing EOP-0 from FIA DDR on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_FIADDR_3

Missing EOP-0 from FIA DDR on bridge-3

Explanation Missing EOP-0 from FIA DDR on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_XAUI_0

Missing EOP-0 from XAUI on bridge-0

Explanation Missing EOP-0 from XAUI on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_XAUI_1

Missing EOP-0 from XAUI on bridge-1

Explanation Missing EOP-0 from XAUI on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_XAUI_2

Missing EOP-0 from XAUI on bridge-2

Explanation Missing EOP-0 from XAUI on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_0_XAUI_3

Missing EOP-0 from XAUI on bridge-3

Explanation Missing EOP-0 from XAUI on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_FIADDR_0

Missing EOP-1 from FIA DDR on bridge-0

Explanation Missing EOP-1 from FIA DDR on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_FIADDR_1

Missing EOP-1 from FIA DDR on bridge-1

Explanation Missing EOP-1 from FIA DDR on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_FIADDR_2

Missing EOP-1 from FIA DDR on bridge-2

Explanation Missing EOP-1 from FIA DDR on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_FIADDR_3

Missing EOP-1 from FIA DDR on bridge-3

Explanation Missing EOP-1 from FIA DDR on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_XAUI_0

Missing EOP-1 from XAUI on bridge-0

Explanation Missing EOP-1 from XAUI on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_XAUI_1

Missing EOP-1 from XAUI on bridge-1

Explanation Missing EOP-1 from XAUI on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_XAUI_2

Missing EOP-1 from XAUI on bridge-2

Explanation Missing EOP-1 from XAUI on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-MISS_EOP_1_XAUI_3

Missing EOP-1 from XAUI on bridge-3

Explanation Missing EOP-1 from XAUI on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_CONST_BP_0

NPU-0 constantly backpressuring bridge - 0

Explanation NPU-0 is constantly backpressuring bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_CONST_BP_1

NPU-0 constantly backpressuring bridge - 1

Explanation NPU-0 is constantly backpressuring bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_CONST_BP_2

NPU-0 constantly backpressuring bridge - 2

Explanation NPU-0 is constantly backpressuring bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_CONST_BP_3

NPU-0 constantly backpressuring bridge - 3

Explanation NPU-0 is constantly backpressuring bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MAXLEN_ERR_0

NPU-0 packet maximum length error - 0

Explanation Packet maximum length error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MAXLEN_ERR_1

NPU-0 packet maximum length error - 1

Explanation Packet maximum length error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MAXLEN_ERR_2

NPU-0 packet maximum length error - 2

Explanation Packet maximum length error on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MAXLEN_ERR_3

NPU-0 packet maximum length error - 3

Explanation Packet maximum length error on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MINLEN_ERR_0

NPU-0 packet minimum length error - 0

Explanation Packet minimum length error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MINLEN_ERR_1

NPU-0 packet minimum length error - 1

Explanation Packet minimum length error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MINLEN_ERR_2

NPU-0 packet minimum length error - 2

Explanation Packet minimum length error on NPU-0 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_PKT_MINLEN_ERR_3

NPU-0 packet minimum length error - 3

Explanation Packet minimum length error on NPU-0 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_SCH_0_HANG_0

NPU-0 scheduler 0 hang - 0

Explanation Scheduler 0 Hang on NPU-0 interface on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_CORE_ERR_0

NPU-0 timestamp core error on bridge - 0

Explanation NPU-0 timestamp core error on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_CORE_ERR_1

NPU-0 timestamp core error on bridge - 1

Explanation NPU-0 timestamp core error on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_CORE_ERR_2

NPU-0 timestamp core error on bridge - 2

Explanation NPU-0 timestamp core error on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_CORE_ERR_3

NPU-0 timestamp core error on bridge - 3

Explanation NPU-0 timestamp core error on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_UPDATE_ERR_0

NPU-0 timestamp update error - 0

Explanation Timestamp update error on NPU-0 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_0_TS_UPDATE_ERR_1

NPU-0 timestamp update error - 1

Explanation Timestamp update error on NPU-0 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_CONST_BP_0

NPU-1 constantly backpressuring bridge - 0

Explanation NPU-1 is constantly backpressuring bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_CONST_BP_1

NPU-1 constantly backpressuring bridge - 1

Explanation NPU-1 is constantly backpressuring bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_CONST_BP_2

NPU-1 constantly backpressuring bridge - 2

Explanation NPU-1 is constantly backpressuring bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_CONST_BP_3

NPU-1 constantly backpressuring bridge - 3

Explanation NPU-1 is constantly backpressuring bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MAXLEN_ERR_0

NPU-1 packet maximum length error - 0

Explanation Packet maximum length error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MAXLEN_ERR_1

NPU-1 packet maximum length error - 1

Explanation Packet maximum length error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MAXLEN_ERR_2

NPU-1 packet maximum length error - 2

Explanation Packet maximum length error on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MAXLEN_ERR_3

NPU-1 packet maximum length error - 3

Explanation Packet maximum length error on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MINLEN_ERR_0

NPU-1 packet minimum length error - 0

Explanation Packet minimum length error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MINLEN_ERR_1

NPU-1 packet minimum length error - 1

Explanation Packet minimum length error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MINLEN_ERR_2

NPU-1 packet minimum length error - 2

Explanation Packet minimum length error on NPU-1 interface on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_PKT_MINLEN_ERR_3

NPU-1 packet minimum length error - 3

Explanation Packet minimum length error on NPU-1 interface on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_CORE_ERR_0

NPU-1 timestamp core error on bridge - 0

Explanation NPU-1 timestamp core error on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_CORE_ERR_1

NPU-1 timestamp core error on bridge - 1

Explanation NPU-1 timestamp core error on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_CORE_ERR_2

NPU-1 timestamp core error on bridge - 2

Explanation NPU-1 timestamp core error on bridge instance-2.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_CORE_ERR_3

NPU-1 timestamp core error on bridge - 3

Explanation NPU-1 timestamp core error on bridge instance-3.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_UPDATE_ERR_0

NPU-1 timestamp update error - 0

Explanation Timestamp update error on NPU-1 interface on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-NPU_1_TS_UPDATE_ERR_1

NPU-1 timestamp update error - 1

Explanation Timestamp update error on NPU-1 interface on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PAR_MERR_0

Multi bit mem parity error - 0

Explanation Multi bit mem parity error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PAR_MERR_1

Multi bit mem parity error - 1

Explanation Multi bit mem parity error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PAR_SERR_0

Single bit mem parity error - 0

Explanation Single bit mem parity error on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PAR_SERR_1

Single bit mem parity error - 1

Explanation Single bit mem parity error on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_FIA_0

Packet length error from FIA for NPU-0 on bridge-0

Explanation Packet length error from FIA for NPU-0 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_FIA_1

Packet length error from FIA for NPU-0 on bridge-1

Explanation Packet length error from FIA for NPU-0 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_FIA_2

Packet length error from FIA for NPU-0 on bridge-2

Explanation Packet length error from FIA for NPU-0 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_FIA_3

Packet length error from FIA for NPU-0 on bridge-3

Explanation Packet length error from FIA for NPU-0 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_XAUI_0

Packet length error - 0 from XAUI on bridge-0

Explanation Packet length error - 0 from XAUI on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_XAUI_1

Packet length error - 0 from XAUI on bridge-1

Explanation Packet length error - 0 from XAUI on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_XAUI_2

Packet length error - 0 from XAUI on bridge-2

Explanation Packet length error - 0 from XAUI on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_0_XAUI_3

Packet length error - 0 from XAUI on bridge-3

Explanation Packet length error - 0 from XAUI on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_FIA_0

Packet length error from FIA for NPU-1 on bridge-0

Explanation Packet length error from FIA for NPU-1 on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_FIA_1

Packet length error from FIA for NPU-1 on bridge-1

Explanation Packet length error from FIA for NPU-1 on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_FIA_2

Packet length error from FIA for NPU-1 on bridge-2

Explanation Packet length error from FIA for NPU-1 on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_FIA_3

Packet length error - 1 from FIA on bridge-3

Explanation Packet length error from FIA for NPU-1 on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_XAUI_0

Packet length error - 1 from XAUI on bridge-0

Explanation Packet length error - 1 from XAUI on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_XAUI_1

Packet length error - 1 from XAUI on bridge-1

Explanation Packet length error - 1 from XAUI on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_XAUI_2

Packet length error - 1 from XAUI on bridge-2

Explanation Packet length error - 1 from XAUI on bridge instance-2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-PKT_LEN_ERR_1_XAUI_3

Packet length error - 1 from XAUI on bridge-3

Explanation Packet length error - 1 from XAUI on bridge instance-3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-SCH_0_HANG_0

Scheduler 0 hang - 0

Explanation Scheduler 0 Hang on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-SCH_0_HANG_1

NPU-0 scheduler 0 hang - 1

Explanation Scheduler 0 Hang on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-SCH_1_HANG_0

Scheduler 1 hang - 0

Explanation Scheduler 1 Hang on bridge instance-0.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-SCH_1_HANG_1

Scheduler 1 hang - 1

Explanation Scheduler 1 Hang on bridge instance-1.

Recommended Action Please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_FRAG_ERR_0

XAUI to NPU-0 fragment error - 0

Explanation XAUI interface to NPU-0 reported fragmentation error on TX side on bridge instance - 0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_FRAG_ERR_1

XAUI to NPU-0 fragment error - 1

Explanation XAUI interface to NPU-0 reported fragmentation error on TX side on bridge instance - 1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_FRAG_ERR_2

XAUI to NPU-0 fragment error - 2

Explanation XAUI interface to NPU-0 reported fragmentation error on TX side on bridge instance - 2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_FRAG_ERR_3

XAUI to NPU-0 fragment error - 3

Explanation XAUI interface to NPU-0 reported fragmentation error on TX side on bridge instance - 3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_FULL_0

XAUI 0 High Queue full error - 0

Explanation Queue full error on XAUI 0 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_FULL_1

XAUI 0 High Queue full error - 1

Explanation Queue full error on XAUI 0 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_OFLOW_0

XAUI 0 High Queue overflow error - 0

Explanation Queue overflow error on XAUI 0 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_OFLOW_1

XAUI 0 High Queue overflow error - 1

Explanation Queue overflow error on XAUI 0 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_PKT_LEN_0

XAUI 0 High Queue packet length error - 0

Explanation Queue packet length error on XAUI 0 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_PKT_LEN_1

XAUI 0 High Queue packet length error - 1

Explanation Queue packet length error on XAUI 0 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_SEQ_0

XAUI 0 High Queue sequence error - 0

Explanation Queue sequence error on XAUI 0 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_HQ_SEQ_1

XAUI 0 High Queue sequence error - 1

Explanation Queue sequence error on XAUI 0 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_FULL_0

XAUI 0 Low Queue full error - 0

Explanation Queue full error on XAUI 0 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_FULL_1

XAUI 0 Low Queue full error - 1

Explanation Queue full error on XAUI 0 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_OFLOW_0

XAUI 0 Low Queue overflow error - 0

Explanation Queue overflow error on XAUI 0 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_OFLOW_1

XAUI 0 Low Queue overflow error - 1

Explanation Queue overflow error on XAUI 0 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_PKT_LEN_0

XAUI 0 Low Queue packet length error - 0

Explanation Queue packet length error on XAUI 0 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_PKT_LEN_1

XAUI 0 Low Queue packet length error - 1

Explanation Queue packet length error on XAUI 0 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_SEQ_0

XAUI 0 Low Queue sequence error - 0

Explanation Queue sequence error on XAUI 0 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_LQ_SEQ_1

XAUI 0 Low Queue sequence error - 1

Explanation Queue sequence error on XAUI 0 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_FULL_0

XAUI 0 Mgmt Queue full error - 0

Explanation Queue full error on XAUI 0 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_FULL_1

XAUI 0 Mgmt Queue full error - 1

Explanation Queue full error on XAUI 0 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_OFLOW_0

XAUI 0 Mgmt Queue overflow error - 0

Explanation Queue overflow error on XAUI 0 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_OFLOW_1

XAUI 0 Mgmt Queue overflow error - 1

Explanation Queue overflow error on XAUI 0 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_PKT_LEN_0

XAUI 0 Mgmt Queue packet length error - 0

Explanation Queue packet length error on XAUI 0 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_PKT_LEN_1

XAUI 0 Mgmt Queue packet length error - 1

Explanation Queue packet length error on XAUI 0 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_SEQ_0

XAUI 0 Mgmt Queue sequence error - 0

Explanation Queue sequence error on XAUI 0 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_0_MQ_SEQ_1

XAUI 0 Mgmt Queue sequence error - 1

Explanation Queue sequence error on XAUI 0 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_FRAG_ERR_0

XAUI to NPU-1 fragment error - 0

Explanation XAUI interface to NPU-1 reported fragmentation error on TX side on bridge instance - 0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_FRAG_ERR_1

XAUI to NPU-1 fragment error - 1

Explanation XAUI interface to NPU-1 reported fragmentation error on TX side on bridge instance - 1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_FRAG_ERR_2

XAUI to NPU-1 fragment error - 2

Explanation XAUI interface to NPU-1 reported fragmentation error on TX side on bridge instance - 2.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_FRAG_ERR_3

XAUI to NPU-1 fragment error - 3

Explanation XAUI interface to NPU-1 reported fragmentation error on TX side on bridge instance - 3.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_FULL_0

XAUI 1 High Queue full error - 0

Explanation Queue full error on XAUI 1 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_FULL_1

XAUI 1 High Queue full error - 1

Explanation Queue full error on XAUI 1 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_OFLOW_0

XAUI 1 High Queue overflow error - 0

Explanation Queue overflow error on XAUI 1 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_OFLOW_1

XAUI 1 High Queue overflow error - 1

Explanation Queue overflow error on XAUI 1 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_PKT_LEN_0

XAUI 1 High Queue packet length error - 0

Explanation Queue packet length error on XAUI 1 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_PKT_LEN_1

XAUI 1 High Queue packet length error - 1

Explanation Queue packet length error on XAUI 1 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_SEQ_0

XAUI 1 High Queue sequence error - 0

Explanation Queue sequence error on XAUI 1 HQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_HQ_SEQ_1

XAUI 1 High Queue sequence error - 1

Explanation Queue sequence error on XAUI 1 HQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_FULL_0

XAUI 1 Low Queue full error - 0

Explanation Queue full error on XAUI 1 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_FULL_1

XAUI 1 Low Queue full error - 1

Explanation Queue full error on XAUI 1 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_OFLOW_0

XAUI 1 Low Queue overflow error - 0

Explanation Queue overflow error on XAUI 1 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_OFLOW_1

XAUI 1 Low Queue overflow error - 1

Explanation Queue overflow error on XAUI 1 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_PKT_LEN_0

XAUI 1 Low Queue packet length error - 0

Explanation Queue packet length error on XAUI 1 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_PKT_LEN_1

XAUI 1 Low Queue packet length error - 1

Explanation Queue packet length error on XAUI 1 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_SEQ_0

XAUI 1 Low Queue sequence error - 0

Explanation Queue sequence error on XAUI 1 LQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_LQ_SEQ_1

XAUI 1 Low Queue sequence error - 1

Explanation Queue sequence error on XAUI 1 LQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_FULL_0

XAUI 1 Mgmt Queue full error - 0

Explanation Queue full error on XAUI 1 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_FULL_1

XAUI 1 Mgmt Queue full error - 1

Explanation Queue full error on XAUI 1 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_OFLOW_0

XAUI 1 Mgmt Queue overflow error - 0

Explanation Queue overflow error on XAUI 1 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_OFLOW_1

XAUI 1 Mgmt Queue overflow error - 1

Explanation Queue overflow error on XAUI 1 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_PKT_LEN_0

XAUI 1 Mgmt Queue packet length error - 0

Explanation Queue packet length error on XAUI 1 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_PKT_LEN_1

XAUI 1 Mgmt Queue packet length error - 1

Explanation Queue packet length error on XAUI 1 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_SEQ_0

XAUI 1 Mgmt Queue sequence error - 0

Explanation Queue sequence error on XAUI 1 MQ on bridge instance-0.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-BRIDGE-3-XAUI_1_MQ_SEQ_1

XAUI 1 Mgmt Queue sequence error - 1

Explanation Queue sequence error on XAUI 1 MQ on bridge instance-1.

Recommended Action If the error persists, please reload the board using the command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CAIBIST Messages

Error Message %PLATFORM-CAIBIST-3-ERR_HW_BIST

[chars] asic instance [dec] bist block [chars] ch [dec] failed on BIST[[hex]].

Explanation BIST failure

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CAIBIST-3-ERR_HW_BIST_INFO

[chars]

Explanation provide BIST failure info

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CAIBIST-3-ERR_HW_BIST_TIMEDOUT

[chars] asic instance [dec] bist block [chars] BIST timedout.

Explanation BIST failure

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CAIBIST-3-ERR_SW_INIT

[chars].

Explanation software initialization error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CANB_SERVER Messages

Error Message %PLATFORM-CANB_SERVER-3-ALARM_CLEARED

Clear alarm from CBC in slot [chars], alarm code [chars]

Explanation Alarm cleared received from CBC, condition has alleviated.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-3-ALARM_INDICATION

Raise alarm from CBC in slot [chars], alarm code [chars]

Explanation Alarm indication received from CBC. This may be a serious failure (example: power sequencer failure), however process may continue functioning as expected (or successfully retry) despite the failure.

Recommended Action Provide the following CLI: (admin)# show env Use the pid from canb-server output to look for matching pid in the pfm output. If the alarm indication does not clear within 30 minutes, contact TAC.

Error Message %PLATFORM-CANB_SERVER-3-ERROR_EXIT

Canbus-server process exiting in [chars].[dec], error code [chars]

Explanation The CAN Bus Server process exited due to the reason mentioned in the message.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Verify process is up and running, give CLI: If it is still non-operational, use CLI: If it is still non-operational, perform card reload. If still non-operational, contacting TAC and performing RSP switchover is recommended.

Error Message %PLATFORM-CANB_SERVER-3-IDPROM_CACHE_OVERFLOW

IDPROM cache write overflow detected at [chars].[dec] on tx_request_array[[dec]].tx_base_ptr, a retry will be scheduled

Explanation This is an error message related to the Canbus Controller processing the received UART message.

Recommended Action Do EP soft/hard OIR, or restart canb-server.

Error Message %PLATFORM-CANB_SERVER-3-INVALID_SLOT

Invalid slot id:[dec] detected at [chars].[dec]

Explanation This is an error message related to the Canbus Controller processing the received message.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-3-INVALID_SLOT_BUS

Invalid slot id:[dec] on bus:[dec] detected at [chars].[dec]

Explanation This is an error message related to the Canbus Controller processing the received message.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-3-MEM_CORRUPT_TX_REQUEST_ARRAY

Memory corruption detected at [chars].[dec] on tx_request_array[[dec]], magic_num expected: [hex], actual [hex]

Explanation This is an error message related to the Canbus Controller processing the received UART message.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-3-MESSAGE_FAILED

Unexpected CBC message received from slot [chars] [ver [dec].[dec]] for msg type [dec], id [dec], len [dec]

Explanation A message was received and did not match any outstanding requests and also is not a standalone message. This is not a critical failure, the process can continue functioning as expected despite the message arrival, message is discarded.

Recommended Action If this appears once or infrequently, it is not necessary to contact TAC. If it appears continuously or comes and goes repeatedly, it is best to please collect the following details and contact TAC. Provide the following CLI output: (admin)# show canb server-stats loc all (admin)# show canb trace loc target nodeid (admin)# debug canb server error loc target nodeid Let the debug run 2 minutes (admin)# undebug canb server error loc target nodeid (admin)# show canb trace loc target nodeid (admin)# show canb server-stats loc all

Error Message %PLATFORM-CANB_SERVER-3-OBFL_CACHE_OVERFLOW

OBFL cache write overflow detected at [chars].[dec] on tx_request_array[[dec]].tx_base_ptr, a retry will be scheduled

Explanation This is an error message related to the Canbus Controller processing the received UART message.

Recommended Action restart canb-server.

Error Message %PLATFORM-CANB_SERVER-3-OPERATION_FAIL

Failed in [chars].[dec], error code [chars]

Explanation The particular operation mentioned in the message failed due to some reason. This may be a serious failure, however process may continue functioning as expected (or successfully retry) despite the failure.

Recommended Action Provide the following debug: (admin)# show canb server-stats loc all (admin)# show canb trace loc target nodeid (admin)# debug canb server error loc target nodeid Let the debug run for 2 minutes (admin)# undebug canb server error loc target nodeid (admin)# show canb server-stats loc all

Error Message %PLATFORM-CANB_SERVER-6-CRC_ERROR

CRC error in Rx message from CBC and recover by retransmit, throttled count equals [dec]

Explanation The message received from Canbus Controller has CRC error computed. This is indicative of a low level serial device transmission error. In most cases, the message is fully recoverable automatically.

Recommended Action Provide the following CLI output: (admin)# show canb trace loc target nodeid (admin)# show canb server-stats loc all (admin)# show env volt Wait 5 minutes, again give CLI: (admin)# show env volt If the voltage output looks correct, then there is likely no negative impact from the CRC error. If the voltage output looks incorrect, wait 30 minutes and give the CLI command again. If the voltage output still looks incorrect, If this error occurs repetitively for a particular card, contact TAC for further evaluation.

Error Message %PLATFORM-CANB_SERVER-6-OPERATION_INFO

[chars].[dec], Info - [chars]

Explanation Informational condition and/or failure. The process can continue functioning as expected despite the failure.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-RP_ISOLATION

[chars] is in RP isolation

Explanation This is an informational message indicating that target RP has transitioned into RP isolation.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-RP_ISOLATION_RESET_REQ

CPU reset request ignored for [chars]

Explanation This is an informational message indicating that RP Isolation is in force, CPU reset request for the target slot is ignored.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-UPGRADE_COMPLETED

CBC upgrade completed on [chars]

Explanation This is an informational message indicating that Canbus Controller firmware upgrade is completed on the specified location.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-UPGRADE_IN_PROGRESS

CBC upgrade in progress on [chars], Page [dec] of range [dec]-[dec]

Explanation This is an informational message indicating that Canbus Controller firmware upgrade is in progress on the specified location. The page that is being presently upgraded is mentioned in the message. This page number would be in the specified range, corresponding to the Canbus Controller partition that is being upgraded.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-UPGRADE_INFO

CBC upgrade on [chars]: [chars]

Explanation This is an informational message related to the Canbus Controller upgrade process on the specified location.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-6-UPGRADE_STARTED

Starting CBC upgrade on [chars] with image [chars]

Explanation This is an informational message indicating that the Canbus Controller firmware on the specified loation is going to be upgraded with the image at the specified path.

Recommended Action No action is required.

Error Message %PLATFORM-CANB_SERVER-7-CBC_POST_RESET_NOTIFICATION

Node [chars], [chars] ([hex][hex]%02x[hex])

Explanation Informational log only

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CANB_SERVER-7-CBC_PRE_RESET_NOTIFICATION

Node [chars], [chars] ([hex][hex]%02x[hex])

Explanation Informational log only

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CANB_SERVER-7-OPERATION_DEBUG

Debug [chars].[dec], [dec], [dec], error code [chars]

Explanation This is a programmed diagnostic debug message.

Recommended Action No action required.

CARD Messages

Error Message %PLATFORM-CARD-0-OVERCURRENT

ClkCtrl detected an overcurrent condition on card [chars]

Explanation ClkCtrl driver detected a card overcurrent condition

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CARDMGR Messages

Error Message %PLATFORM-CARDMGR-3-BAD_CS_INFO

could not get CS revision info!

Explanation Could not get CS revision info

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-CHDIR_FAILED

chdir to [chars] failed: [chars]

Explanation Chdir failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-MODULE_UNAVAILABLE

module [chars] not available

Explanation Module unavailable

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-NO_CARDS_DEFINED

no cards defined

Explanation No cards defined

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-NO_DRIVERS_FOUND

no device drivers defined

Explanation No device drivers

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-NO_SOCKETS

no sockets found!

Explanation No sockets

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-PCMCIA_INIT_ERROR

PCMCIA initialization error at: [chars]

Explanation PCMCIA initialization error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-SELECT_FAILURE

select (): [chars]

Explanation Select failure

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-3-UNSUPPORTED_CARD

Unsupported card in socket [dec]

Explanation Unsupported card

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-6-PRODUCT_INFO

product info: [chars]

Explanation Product info

Recommended Action No action is required.

Error Message %PLATFORM-CARDMGR-6-SOCKET_INFO

socket [dec]: [chars]

Explanation Socket info

Recommended Action No action is required.

Error Message %PLATFORM-CARDMGR-7-ADJ_RES_FAILED

could not adjust resource: [chars]: [chars]

Explanation Could not adjust resource

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-BAD_OPEN

could not open [chars]: [chars]

Explanation Open of file failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-BIND_FAILED

bind ’[chars]’ to socket [dec] failed: [chars]

Explanation Bind failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-BIND_MTD_REGION_FAILED

bind MTD ’[chars]’ to region at [hex] failed: [chars]

Explanation Bind mtd region failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-BIND_MTD_SOCKET_FAILED

bind MTD ’[chars]’ to socket [dec] failed: [chars]

Explanation Bind mtd to socket failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-CIS_DATA_PARSING_ERROR

error parsing CIS([hex]) on socket [dec]: [chars]

Explanation CIS data parsing error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-CIS_DATA_READ_ERROR

error reading CIS data on socket [dec]: [chars]

Explanation CIS data read error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-CIS_REPLACE_ERROR

could not replace CIS: [chars]

Explanation CIS replace error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-CS_REL_MISMATCH

Card Services release does not match

Explanation Release mismatch

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-GET_DEV_INFO_FAILED

get device info on socket [dec] failed: [chars]

Explanation Device info failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-NO_MEM

Malloc failure

Explanation Out of memory

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-OPEN_SOCK_FAILED

open_sock(socket [dec]) failed: [chars]

Explanation Open of socket failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-READ_FAILED

read ([dec]): [chars]

Explanation Read failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-THREAD_CREATE_FAILED

Thread create failed: [chars]

Explanation Thread create failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-UNBIND_FAILED

unbind ’[chars]’ from socket [dec] failed: [chars]

Explanation Unbind failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CARDMGR-7-UNBIND_MTD_FAILED

unbind MTD ’[chars]’ from socket [dec] failed: [chars]

Explanation Unbind MTD failed

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CBC Messages

Error Message %PLATFORM-CBC-1-CANBUS_A_FAILED

CBC A failed

Explanation CBC detected CANBUS A failure. This may be a serious failure, however the system may continue functioning as expected despite the failure.

Recommended Action Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-CANBUS_B_FAILED

CBC B failed

Explanation CBC detected CANBUS B failure. This may be a serious failure, however the system may continue functioning as expected despite the failure.

Recommended Action Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-CANBUS_BOTH_FAILED

Canbus A and B have failed

Explanation CBC detected both CANBUS A and CANBUS B have failed. This may be a serious hardware failure.

Recommended Action Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-CANBUS_FANTRAY_INRUSH_FAILED

CBC inrush fantray has failed

Explanation CBC has detected that the inrush fantray has failed. This will result in the LCs getting overheated. Please turn off power to the system.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-CANBUS_PWR_FUSE_FAILED

CBC power fuse has failed

Explanation CBC has detected power fuse failure. The proper functioning of the board requies that the current drawn be within the rating of the boards power fuse.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-CANBUS_PWR_SEQ_FAILED

CBC power sequence failed

Explanation The CBC alarm indicating that the power up sequence has failed. The proper functioning of the board requires that a successful application of power be applied to the board in the proper sequence.

Recommended Action Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-SLOT_ID_CHANGE

CBC slot id changed

Explanation CBC detected unexpected slot id change. The system can no longer manage/monitor the card’s environment conditions.

Recommended Action Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CBC-1-VERSION_ERROR

CBC major version error on node [chars]. Expected equals [dec], Actual equals [dec]

Explanation The CBC on the slot has an incorrect firmware type programmed. The firmware major version does not match the card type.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CCI_HAL_SATORI Messages

Error Message %PLATFORM-CCI_HAL_SATORI-3-ERR_TX_PKT

[chars]: [dec] [chars]

Explanation CCI HAL SATORI Packet transmit error.

Recommended Action Execute spp_pdma_show_ltrace from the kshell of the card where this message was seen.

CCI_SSTAR Messages

Error Message %PLATFORM-CCI_SSTAR-3-ERR_DRV_INIT

CPUCtrl (SSTAR) Initialization failed: [chars]

Explanation The cpuctrl (sstar) driver detected an error during initialization.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CCI_SSTAR-3-ERR_EVM_CREATE

Failed to create event manager

Explanation The Fabric driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CCI_SSTAR-3-ERR_INTERRUPT_THREAD_EXIT

[chars] priority interrupt thread failed. Exiting.

Explanation The cpuctrl (sstar) driver detected a critical failure in the interrupt thread initialization. Abort and exit the thread.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CCTL_ENS Messages

Error Message %PLATFORM-CCTL_ENS-3-ERROR_EXIT

Envmon process exiting because [chars], error code [chars]

Explanation The Chassis Control driver process exited due to the reason mentioned in the message.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute ’show process envmon location ’ to verify that the process is up and running. If it is still non-operational, try doing from the admin mode ’process restart envmon location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CCTL_ENS-7-OPERATION_FAIL

Failed to [chars], error code [chars]

Explanation The particular operation mentioned in the message failed due to some reason. This is not a critical failure, the process can continue functioning as expected despite the failure.

Recommended Action Debug message only. No action is required.

CCTL Messages

Error Message %PLATFORM-CCTL-2-CARD_POWERUP_FAIL

Unable to powerup card(for node:[chars]) rc: [chars]

Explanation The hardware powerup was unsuccessful due to the mentioned reason.

Recommended Action Card powerup is typically initiated when a card needs to power. If that fails, please collect ’show cctl trace shelfmgr loc ’ from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-CARD_SHUTDOWN_FAIL

Unable to shutdown card(for node: [chars]) rc: [chars]

Explanation The shutdown of the card was unsuccessful due to the mentioned reason.

Recommended Action Card shutdown is typically initiated when a card needs to be hard reset. If that fails, only a software reset be initiated. Please collect ’show cctl trace shelfmgr loc’ from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-CHASSIS_SHUTDOWN_FAIL

Unable to shutdown chassis because [chars]

Explanation The shutdown of the chassis was unsuccessful due to the mentioned reason.

Recommended Action Chassis shutdown is typically initiated due to some critical failure. If the software initiated chassis shutdown has failed, then user should intervene and shut down the chassis manually.

Error Message %PLATFORM-CCTL-2-CPLD_POWER_ALARM

Fabric PLD [chars] interrupt detected instance [dec] Channel [dec] [chars] register: [hex]

Explanation The Fabric PLD power fault alarm was encountered

Recommended Action A power fault has occurred.If the fault has occurred, node will be shutdown. Please collect syslog and cctl client debug’s from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-CPLD_POWER_CTRL_ALARM

Fabric PLD [chars] interrupt detected instance [dec] [chars] register [hex]

Explanation The Fabric PLD power fault alarm was encountered

Recommended Action A power fault has occurred.If the fault has occurred, node will be shutdown. Please collect syslog and cctl client debug’s from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-MB_POWERUP_CHECK_FAIL

Voltage validation failed, motherboard did not power up. Shutting down card.

Explanation The voltage validation and power status check for the card failed. This might be a power issue to the card or a faulty card.

Recommended Action Try reloading the card or physical OIR, verify power to chassis and the card.

Error Message %PLATFORM-CCTL-2-RESET_SP_FAIL

Unable to reset SP node([chars]) rc: [chars]

Explanation The hard reset of sp was unsuccessful due to the mentioned reason.

Recommended Action Reset of SP is typically initiated when that SP needs to be hard reset. If that fails, only a software reset be initiated. Please collect ’show cctl trace shelfmgr loc’ from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-STANDBY_SHUTDOWN_FAILED

Unable to shutdown the standby node as part of chassis shutdown

Explanation The shutdown of the standby SC/RP node failed during the chassis shutdown process.

Recommended Action Please power off the chassis manually.

Error Message %PLATFORM-CCTL-2-TAIKO_POWER_ALARM

[chars] Alarm detected on Taiko node([dec]) register: [hex]

Explanation The taiko power alarm was encountered

Recommended Action Node will be shutdown immediately as hardware error occured. Please collect ’show cctl trace error’ from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-2-TAIKO_TEMP_ALARM

[chars] Alarm detected on Taiko node([dec]) register: [hex]

Explanation The taiko temperature alarm was encountered

Recommended Action Node will be shutdown immediately as hardware error occured. Please collect ’show cctl trace error’ from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-3-BARBARIAN_VOLT_FIX_FAILED

Voltage fix on VP4 could not be activated for Barbarian SPA in slot [dec]

Explanation VP4 rail on the SPA could not be margined to nominal voltage due to some failure.

Recommended Action SAR chip SRAM parity errors might result. Margin the rail manually.

Error Message %PLATFORM-CCTL-3-ERROR_EXIT

Envmon process exiting because [chars], error code [chars]

Explanation The Chassis Control driver process exited due to the reason mentioned in the message.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute ’show process envmon location ’ to verify that the process is up and running. If it is still non-operational, try doing from the admin mode ’process restart envmon location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_CLEAR_LED

An I2C failure occurred while trying to clear the alarm LED(s).

Explanation An I2C failure occurred while trying to clear one or more of the alarm card LEDs.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_HANG

Unable to recover from I2C bus hang for sensor [chars].

Explanation An I2C bus hang was encountered when attempting to access a sensor.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_PM_CLEAR_FAULT

An I2C failure occurred while trying to clear the fault status of Power Module id: [dec].

Explanation An I2C error was encountered when attempting to clear the fault / alarm information of a Power Module.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_PM_FAULT

An I2C failure occurred while checking the fault status of Power Module id: [dec].

Explanation An I2C error was encountered when attempting to access the fault / alarm information of a Power Module.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_PM_LED

An I2C failure occurred while trying to set the Power Module presence LED(s).

Explanation An I2C failure occurred while trying to set or clear the LEDs of a Power Module in a power shelf.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_PM_PRESENCE

An I2C failure occurred while checking for the presence of Power Modules in [chars].

Explanation This I2C failure indicates that there was a fault when checking the presence information for the Power Modules in a power shelf. The shelf might have been removed or is not inserted correctly.

Recommended Action Check that the shelf is present and seated correctly.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_PM_SENSOR

An I2C failure occurred when reading sensor [chars] for Power Module id: [dec].

Explanation An I2C error was encountered when attempting to read a sensor on a Power Module.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_SET_LED

An I2C failure occurred while trying to set the alarm LED(s).

Explanation An I2C failure occurred while trying to set one or more of the alarm card LEDs.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-I2C_FAILURE_ZONE

An I2C failure occurred while checking the zone breaker status in [chars].

Explanation This I2C failure indicates that a fault occurred when checking the circuit breaker status on the shelf.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-MASTERSHIP_EXIT

Exiting because not able to [chars] mastership

Explanation The Chassis Control driver process exited as it was not able to grab mastership or unable to release it.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-3-READ_POWER_SHELF_TYPE_FAILURE

Unable to detect power shelf type. Assuming AC shelf and continuing for now. Please check EEPROM programming on power shelf backplane.

Explanation We are unable to read the power shelf backplane EEPROM for some reason. Need to check the programming of the backplane.

Recommended Action Check that the power-shelf is seated correctly, and that the backplane EEPROM is programmed correctly. In the admin mode, use ’show diag power-supply eeprom-info’ to check the contents of the EEPROM.

Error Message %PLATFORM-CCTL-3-UNKNOWN_CHASSIS_ID

Unknown Controller/Platform type [hex] read from EEPROM.

Explanation The value read from the EEPROM does not match any of the known Controller/platform type values.

Recommended Action Please check the EEPROM programming. ’show diag eeprom-info’ in admin mode gives a raw dump of the EEPROM data. Refer EDCS-137763 to interpret the data to check if the Controller/Platform type is programmed correctly or not. If the Controller/Platform type is incorrect, the unit will have to be RMA’d to reprogram the EEPROM correctly. If the Controller/Platform type is correct, EEPROM read is failed due to unknown reason, Its Recommended to Hard OIR of the card.

Error Message %PLATFORM-CCTL-4-BARBARIAN_VOLT_FIX_ACTIVE

Voltage fix on VP4 active for Barbarian SPA in slot [dec]

Explanation VP4 rail on the SPA is margined to nominal voltage due to SAR chip errata.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-4-CPLD_POWER_SEQUENCER_FAULT_OR_ALERT

Power Sequencer [inst: [dec] channel: [dec] sensor_type: [chars]] detected alarm [chars] value: [dec] threshold: [dec]

Explanation The fabric power sequencer detected a temperature or power alarm.

Recommended Action An alarm was detected. If a critical alarm is detected node will be shutdown. Please collect syslog and cctl client debugs from the node where alarm was detected.

Error Message %PLATFORM-CCTL-4-CPLD_POWER_WARN

Fabric PLD [chars] interrupt detected instance [dec] Channel [dec] [chars] register: [hex]

Explanation The Fabric PLD power alert was encountered

Recommended Action A power alert has occurred. If the alert has occurred, node will not be shutdown. Please collect syslog and cctl client debug’s from the node on which this ios-msg is seen.

Error Message %PLATFORM-CCTL-4-UNKNOWN_SHELF_ID

Unknown shelf ID [hex] read from power shelf backplane EEPROM - please check EEPROM programming.

Explanation The value read from the power shelf backplane does not match any of the known shelf ID values. Please check the EEPROM programming.

Recommended Action Please check the EEPROM programming of the power-shelf backplane. ’show diag power-supply eeprom-info’ in admin mode gives a raw dump of the EEPROM data. Refer EDCS-137763 to interpret the data to check if the shelf ID is programmed correctly or not. If the shelf ID is incorrect, the unit will have to be RMA’d to reprogram the EEPROM correctly.

Error Message %PLATFORM-CCTL-6-OPERATION_SUCCESS

[chars]

Explanation The particular operation mentioned in the message succeeded.

Recommended Action No action is required.

Error Message %PLATFORM-CCTL-6-TEMP_ALARM

[chars] alarm occured for [chars] sensor at temperature [dec] deg C, against configured threshold of [dec] deg C

Explanation Informational msg indicating temperature at which alarm occured.

Recommended Action Software will take corrective action on its own. No action is required.

Error Message %PLATFORM-CCTL-6-TEMP_READ_ERR

Invalid temp value read for [chars] sensor.

Explanation Informational msg indicating invalid temperature read

Recommended Action Software will take corrective action on its own. No action is required.

Error Message %PLATFORM-CCTL-7-OPERATION_FAIL

Failed to [chars], error code [chars]

Explanation The particular operation mentioned in the message failed due to some reason. This is not a critical failure, the process can continue functioning as expected despite the failure.

Recommended Action Debug message only. No action is required.

CE_SWITCH Messages

Error Message %PLATFORM-CE_SWITCH-2-DEADLINE_MONITOR_FAILED

Switch process failed to register with deadline monitor, error [chars]

Explanation ce-switch process failed to register with deadline monitor

Recommended Action No action is required.

Error Message %PLATFORM-CE_SWITCH-2-LINK_SHUT_DOWN

Intra-rack switch port [dec] state changed to ADMIN_DOWN

Explanation The intra-rack switch port was administratively shut down.

Recommended Action No action is required.

Error Message %PLATFORM-CE_SWITCH-2-STACKING_LINK_DOWN

Broadcom switch stacking link down

Explanation The driver was unable to successfully initialise the stacking link

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CE_SWITCH-3-DMAC_LINK_STATE_CHANGE

CE_SWITCH DMAC link interface ([dec]) is down

Explanation The internal link interface for the specified port is down.

Recommended Action The board would get reloaded. On reload of board, run following commands from RSP ksh to decode PCDS information - pcds_decode -c CE_SWITCH.pcds file. pcds_decode -c NIANTIC.pcds file. If users has auto reset option disabled in admin config, then the board would not get reloaded on its own. At this stage collect the output of (admin)’show tech support control ethernet location nodeId’

Error Message %PLATFORM-CE_SWITCH-6-BADSFP

Front panel nV Edge Control Port [dec] has unsupported SFP plugged in.
Port is disabled, please plug in Cisco support 1Gig SFP for port to be enabled

Explanation nV Edge Control ports needs Cisco supported SFPs.

Recommended Action ’Plug in a Cisco supported 1Gig SFP’

Error Message %PLATFORM-CE_SWITCH-6-ERRDIS


Front Panel port [dec] error disabled because of UDLD
uni directional forwarding. There will be automatic
retries to try and bring up the port periodically

Explanation Front panel SFP port is UDLD Uni-Directional, check sfp/fiber for errors

Recommended Action ’Check if the media (fiber / sfp) has any errors’

Error Message %PLATFORM-CE_SWITCH-6-UPDN

Interface [dec] ([chars]) is [chars]

Explanation A link to the RSP control plane switch has change state.

Recommended Action ’Copy the error message exactly as it appears on the console or in the system log. Issue the show controllers ce-switch link detail location loc in msg command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show controllers ce-switch link detail location loc in msg output, call your Cisco technical support representative and provide the representative with the gathered information.’

CEMGBL Messages

Error Message %PLATFORM-CEMGBL-2-CRIT

[chars] : [chars]

Explanation An unexpected critical error condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-2-CRIT

[chars] : [chars]

Explanation An unexpected critical error condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-2-SFP_INVALID_TYPE

CE SFP monitor init failed with invalid board type [hex]

Explanation An unexpected failure in register notification failed.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-2-SFP_INVALID_TYPE

CE SFP monitor init failed with invalid board type [hex]

Explanation An unexpected failure in register notification failed.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-4-WARNING

[chars] : [chars]

Explanation An unexpected condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-4-WARNING

[chars] : [chars]

Explanation An unexpected condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-5-SFP_OIR

Control-ethernet external gigabit sfp [chars] - [chars]

Explanation The control-eth ext ge sfp state changed

Recommended Action No action is required.

Error Message %PLATFORM-CEMGBL-5-SFP_OIR

Control-ethernet external gigabit sfp [chars] - [chars]

Explanation The control-eth ext ge sfp state changed

Recommended Action No action is required.

Error Message %PLATFORM-CEMGBL-7-ERROR

[chars] : [chars]

Explanation An unexpected error condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-7-ERROR

[chars] : [chars]

Explanation An unexpected error condition encountered.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-7-REGISTER_NOTIFY_FAIL

CE register notification failed with cb : [hex] intf : [hex] num_elements : [hex]

Explanation An unexpected failure in register notification failed.

Recommended Action Collect system log information. No action is required.

Error Message %PLATFORM-CEMGBL-7-REGISTER_NOTIFY_FAIL

CE register notification failed with cb : [hex] intf : [hex] num_elements : [hex]

Explanation An unexpected failure in register notification failed.

Recommended Action Collect system log information. No action is required.

CETHHA Messages

Error Message %PLATFORM-CETHHA-2-CRITICAL

Hardware error on control-ethernet port [chars]

Explanation Hardware error on CPU control ethernet port.

Recommended Action Remove/Replace the RP.

Error Message %PLATFORM-CETHHA-2-PORT_FAULT

High rate of errors on control ethernet port [chars]

Explanation The rate of link errors on the control ethernet port has exceeded the threshold. The link should be fixed to avoid disruption in router services.

Recommended Action Fix the bad link after switching traffic to redundant link.

Error Message %PLATFORM-CETHHA-4-NOGE

RP does not have GE connectivity

Explanation RP does not have GE connectivity. Reload/failovers may cause problems.

Recommended Action Check the GE connections on the front panel of the RP/SC and re-connect/replace to make sure atleast one GE connection is there.

Error Message %PLATFORM-CETHHA-7-STATS_INFO

Statistics: [chars]

Explanation Packet tx/rx statistics on CPU control ethernet port.

Recommended Action Remove/Replace the RP.

CFP Messages

Error Message %PLATFORM-CFP-2-DEV_CFP_COMPLIANCE_ERROR

CFP Module for port [dec] is not Cisco compliant

Explanation A compliance error was detected during CFP initialization. A compliance error is due to checksum error, EEPROM CRC error, vendor data error, or decryption error. The CFP is the pluggable optics on the line cards. CFP initialization may happen when linecard boots up, CFP OIR and line card process restart. The optics will not be enabled if an CFP compliance error is detected.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands ’show controller i/f phy’ and ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-DEV_CFP_OPTICS_PORT_UNSUP

CFP Module for port [dec] is not supported

Explanation A CFP Module not supported for the port error was detected during CFP initialization. A CFP Module not supported for the port error is reported when Optics is not supported on the port. The CFP is the pluggable optics on the line cards. CFP initialization may happen when linecard boots up, SFP OIR and line card process restart. Traffic will not be impacted by this error.

Recommended Action Verify that the CFP Module is supported for the port. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands ’show controller i/f phy’ and ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-DEV_CFP_PID_NOT_SUPPORTED

CFP Module for port [dec] is not a supported Product ID (PID)

Explanation A PID not supported error was detected during CFP initialization. A PID not support error is reported when either the PID can not be read it not supported on the platform. The CFP is the pluggable optics on the line cards. CFP initialization may happen when linecard boots up, CFP OIR and line card process restart. Traffic will not be impacted by this error.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands ’show controller i/f phy’ and ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-DEV_CFP_SUPPORTED_ERROR

CFP Module for port [dec] is not a supported module type

Explanation A supported error was detected during CFP initialization. A support error is reported when the CFP type can not be determined or it is not supported on the platform. The CFP is the pluggable optics on the line cards. CFP initialization may happen when linecard boots up, CFP OIR and line card process restart. The optics will not be enabled if an CFP supported error is detected.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands ’show controller i/f phy’ and ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-HIGH_BIAS_ALARM

CFP Case High Bias Alarm

Explanation Environmental monitoring has detected a CFP case bias greater than or equal to the high bias alarm threshold. The CFP is the pluggable optics on the line cards. The bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-HIGH_TEMP_ALARM

CFP Case High Temperature Alarm

Explanation Environmental monitoring has detected a CFP case temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-HIGH_VOLTAGE_ALARM

CFP Case High Voltage Alarm

Explanation Environmental monitoring has detected an CFP case voltage greater than or equal to the high voltage alarm threshold. The CFP is the pluggable optics on the line cards. The voltage threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_HIGH_BIAS_ALARM

CFP Lane 0 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_HIGH_RX_POWER_ALARM

CFP Lane 0 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_HIGH_TEMP_ALARM

CFP Lane 0 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_0_HIGH_TX_POWER_ALARM

CFP Lane 0 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_LOW_BIAS_ALARM

CFP Lane 0 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_LOW_RX_POWER_ALARM

CFP Lane 0 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_0_LOW_TEMP_ALARM

CFP Lane 0 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_0_LOW_TX_POWER_ALARM

CFP Lane 0 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_HIGH_BIAS_ALARM

CFP Lane 1 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_HIGH_RX_POWER_ALARM

CFP Lane 1 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_HIGH_TEMP_ALARM

CFP Lane 1 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_1_HIGH_TX_POWER_ALARM

CFP Lane 1 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_LOW_BIAS_ALARM

CFP Lane 1 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_LOW_RX_POWER_ALARM

CFP Lane 1 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_1_LOW_TEMP_ALARM

CFP Lane 1 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_1_LOW_TX_POWER_ALARM

CFP Lane 1 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_HIGH_BIAS_ALARM

CFP Lane 10 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_HIGH_RX_POWER_ALARM

CFP Lane 10 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_HIGH_TEMP_ALARM

CFP Lane 10 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_10_HIGH_TX_POWER_ALARM

CFP Lane 10 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_LOW_BIAS_ALARM

CFP Lane 10 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_LOW_RX_POWER_ALARM

CFP Lane 10 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_10_LOW_TEMP_ALARM

CFP Lane 10 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_10_LOW_TX_POWER_ALARM

CFP Lane 10 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_HIGH_BIAS_ALARM

CFP Lane 11 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_HIGH_RX_POWER_ALARM

CFP Lane 11 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_HIGH_TEMP_ALARM

CFP Lane 11 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_11_HIGH_TX_POWER_ALARM

CFP Lane 11 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_LOW_BIAS_ALARM

CFP Lane 11 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_LOW_RX_POWER_ALARM

CFP Lane 11 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_11_LOW_TEMP_ALARM

CFP Lane 11 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_11_LOW_TX_POWER_ALARM

CFP Lane 11 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_HIGH_BIAS_ALARM

CFP Lane 12 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_HIGH_RX_POWER_ALARM

CFP Lane 12 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_HIGH_TEMP_ALARM

CFP Lane 12 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_12_HIGH_TX_POWER_ALARM

CFP Lane 12 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_LOW_BIAS_ALARM

CFP Lane 12 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_LOW_RX_POWER_ALARM

CFP Lane 12 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_12_LOW_TEMP_ALARM

CFP Lane 12 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_12_LOW_TX_POWER_ALARM

CFP Lane 12 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_HIGH_BIAS_ALARM

CFP Lane 13 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_HIGH_RX_POWER_ALARM

CFP Lane 13 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_HIGH_TEMP_ALARM

CFP Lane 13 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_13_HIGH_TX_POWER_ALARM

CFP Lane 13 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_LOW_BIAS_ALARM

CFP Lane 13 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_LOW_RX_POWER_ALARM

CFP Lane 13 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_13_LOW_TEMP_ALARM

CFP Lane 13 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_13_LOW_TX_POWER_ALARM

CFP Lane 13 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_HIGH_BIAS_ALARM

CFP Lane 14 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_HIGH_RX_POWER_ALARM

CFP Lane 14 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_HIGH_TEMP_ALARM

CFP Lane 14 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_14_HIGH_TX_POWER_ALARM

CFP Lane 14 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_LOW_BIAS_ALARM

CFP Lane 14 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_LOW_RX_POWER_ALARM

CFP Lane 14 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_14_LOW_TEMP_ALARM

CFP Lane 14 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_14_LOW_TX_POWER_ALARM

CFP Lane 14 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_HIGH_BIAS_ALARM

CFP Lane 15 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_HIGH_RX_POWER_ALARM

CFP Lane 15 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_HIGH_TEMP_ALARM

CFP Lane 15 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_15_HIGH_TX_POWER_ALARM

CFP Lane 15 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_LOW_BIAS_ALARM

CFP Lane 15 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_LOW_RX_POWER_ALARM

CFP Lane 15 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_15_LOW_TEMP_ALARM

CFP Lane 15 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_15_LOW_TX_POWER_ALARM

CFP Lane 15 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_HIGH_BIAS_ALARM

CFP Lane 2 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_HIGH_RX_POWER_ALARM

CFP Lane 2 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_HIGH_TEMP_ALARM

CFP Lane 2 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_2_HIGH_TX_POWER_ALARM

CFP Lane 2 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_LOW_BIAS_ALARM

CFP Lane 2 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_LOW_RX_POWER_ALARM

CFP Lane 2 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_2_LOW_TEMP_ALARM

CFP Lane 2 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_2_LOW_TX_POWER_ALARM

CFP Lane 2 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_HIGH_BIAS_ALARM

CFP Lane 3 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_HIGH_RX_POWER_ALARM

CFP Lane 3 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_HIGH_TEMP_ALARM

CFP Lane 3 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_3_HIGH_TX_POWER_ALARM

CFP Lane 3 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_LOW_BIAS_ALARM

CFP Lane 3 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_LOW_RX_POWER_ALARM

CFP Lane 3 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_3_LOW_TEMP_ALARM

CFP Lane 3 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_3_LOW_TX_POWER_ALARM

CFP Lane 3 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_HIGH_BIAS_ALARM

CFP Lane 4 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_HIGH_RX_POWER_ALARM

CFP Lane 4 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_HIGH_TEMP_ALARM

CFP Lane 4 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_4_HIGH_TX_POWER_ALARM

CFP Lane 4 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_LOW_BIAS_ALARM

CFP Lane 4 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_LOW_RX_POWER_ALARM

CFP Lane 4 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_4_LOW_TEMP_ALARM

CFP Lane 4 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_4_LOW_TX_POWER_ALARM

CFP Lane 4 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_HIGH_BIAS_ALARM

CFP Lane 5 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_HIGH_RX_POWER_ALARM

CFP Lane 5 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_HIGH_TEMP_ALARM

CFP Lane 5 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_5_HIGH_TX_POWER_ALARM

CFP Lane 5 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_LOW_BIAS_ALARM

CFP Lane 5 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_LOW_RX_POWER_ALARM

CFP Lane 5 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_5_LOW_TEMP_ALARM

CFP Lane 5 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_5_LOW_TX_POWER_ALARM

CFP Lane 5 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_HIGH_BIAS_ALARM

CFP Lane 6 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_HIGH_RX_POWER_ALARM

CFP Lane 6 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_HIGH_TEMP_ALARM

CFP Lane 6 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_6_HIGH_TX_POWER_ALARM

CFP Lane 6 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_LOW_BIAS_ALARM

CFP Lane 6 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_LOW_RX_POWER_ALARM

CFP Lane 6 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_6_LOW_TEMP_ALARM

CFP Lane 6 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_6_LOW_TX_POWER_ALARM

CFP Lane 6 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_HIGH_BIAS_ALARM

CFP Lane 7 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_HIGH_RX_POWER_ALARM

CFP Lane 7 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_HIGH_TEMP_ALARM

CFP Lane 7 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_7_HIGH_TX_POWER_ALARM

CFP Lane 7 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_LOW_BIAS_ALARM

CFP Lane 7 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_LOW_RX_POWER_ALARM

CFP Lane 7 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_7_LOW_TEMP_ALARM

CFP Lane 7 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_7_LOW_TX_POWER_ALARM

CFP Lane 7 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_HIGH_BIAS_ALARM

CFP Lane 8 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_HIGH_RX_POWER_ALARM

CFP Lane 8 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_HIGH_TEMP_ALARM

CFP Lane 8 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_8_HIGH_TX_POWER_ALARM

CFP Lane 8 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_LOW_BIAS_ALARM

CFP Lane 8 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_LOW_RX_POWER_ALARM

CFP Lane 8 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_8_LOW_TEMP_ALARM

CFP Lane 8 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_8_LOW_TX_POWER_ALARM

CFP Lane 8 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_HIGH_BIAS_ALARM

CFP Lane 9 High Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_HIGH_RX_POWER_ALARM

CFP Lane 9 High Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_HIGH_TEMP_ALARM

CFP Lane 9 High Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_9_HIGH_TX_POWER_ALARM

CFP Lane 9 High Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_LOW_BIAS_ALARM

CFP Lane 9 Low Bias Alarm

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_LOW_RX_POWER_ALARM

CFP Lane 9 Low Rx Power Alarm

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power alarm threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LANE_9_LOW_TEMP_ALARM

CFP Lane 9 Low Temperature Alarm

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LANE_9_LOW_TX_POWER_ALARM

CFP Lane 9 Low Tx Power Alarm

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power alarm threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LOW_BIAS_ALARM

CFP Case Low Bias Alarm

Explanation Environmental monitoring has detected a CFP case bias less than or equal to the low laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-2-LOW_TEMP_ALARM

CFP Case Low Temperature Alarm

Explanation Environmental monitoring has detected an CFP case temperature less than or equal to the low temperature alarm threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-2-LOW_VOLTAGE_ALARM

CFP Case Low Voltage Alarm

Explanation Environmental monitoring has detected a CFP case voltage less than or equal to the low voltage alarm threshold. The CFP is the pluggable optics on the line cards. The voltage threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-HIGH_BIAS_WARNING

CFP Case High Bias Warning

Explanation Environmental monitoring has detected a CFP case bias greater than or equal to the high bias warning threshold. The CFP is the pluggable optics on the line cards. The bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-HIGH_TEMP_WARNING

CFP Case High Temperature Warning

Explanation Environmental monitoring has detected a CFP case temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-HIGH_VOLTAGE_WARNING

CFP Case High Voltage Warning

Explanation Environmental monitoring has detected a CFP case voltage greater than or equal to the high voltage warning threshold. The CFP is the pluggable optics on the line cards. The voltage threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_HIGH_BIAS_WARNING

CFP Lane 0 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_HIGH_RX_POWER_WARNING

CFP Lane 0 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_HIGH_TEMP_WARNING

CFP Lane 0 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_0_HIGH_TX_POWER_WARNING

CFP Lane 0 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_LOW_BIAS_WARNING

CFP Lane 0 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_LOW_RX_POWER_WARNING

CFP Lane 0 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_0_LOW_TEMP_WARNING

CFP Lane 0 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_0_LOW_TX_POWER_WARNING

CFP Lane 0 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_HIGH_BIAS_WARNING

CFP Lane 1 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_HIGH_RX_POWER_WARNING

CFP Lane 1 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_HIGH_TEMP_WARNING

CFP Lane 1 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_1_HIGH_TX_POWER_WARNING

CFP Lane 1 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_LOW_BIAS_WARNING

CFP Lane 1 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_LOW_RX_POWER_WARNING

CFP Lane 1 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_1_LOW_TEMP_WARNING

CFP Lane 1 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_1_LOW_TX_POWER_WARNING

CFP Lane 1 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_HIGH_BIAS_WARNING

CFP Lane 10 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_HIGH_RX_POWER_WARNING

CFP Lane 10 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_HIGH_TEMP_WARNING

CFP Lane 10 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_10_HIGH_TX_POWER_WARNING

CFP Lane 10 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_LOW_BIAS_WARNING

CFP Lane 10 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_LOW_RX_POWER_WARNING

CFP Lane 10 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_10_LOW_TEMP_WARNING

CFP Lane 10 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_10_LOW_TX_POWER_WARNING

CFP Lane 10 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_HIGH_BIAS_WARNING

CFP Lane 11 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_HIGH_RX_POWER_WARNING

CFP Lane 11 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_HIGH_TEMP_WARNING

CFP Lane 11 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_11_HIGH_TX_POWER_WARNING

CFP Lane 11 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_LOW_BIAS_WARNING

CFP Lane 11 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_LOW_RX_POWER_WARNING

CFP Lane 11 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_11_LOW_TEMP_WARNING

CFP Lane 11 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_11_LOW_TX_POWER_WARNING

CFP Lane 11 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_HIGH_BIAS_WARNING

CFP Lane 12 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_HIGH_RX_POWER_WARNING

CFP Lane 12 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_HIGH_TEMP_WARNING

CFP Lane 12 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_12_HIGH_TX_POWER_WARNING

CFP Lane 12 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_LOW_BIAS_WARNING

CFP Lane 12 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_LOW_RX_POWER_WARNING

CFP Lane 12 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_12_LOW_TEMP_WARNING

CFP Lane 12 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_12_LOW_TX_POWER_WARNING

CFP Lane 12 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_HIGH_BIAS_WARNING

CFP Lane 13 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_HIGH_RX_POWER_WARNING

CFP Lane 13 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_HIGH_TEMP_WARNING

CFP Lane 13 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_13_HIGH_TX_POWER_WARNING

CFP Lane 13 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_LOW_BIAS_WARNING

CFP Lane 13 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_LOW_RX_POWER_WARNING

CFP Lane 13 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_13_LOW_TEMP_WARNING

CFP Lane 13 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_13_LOW_TX_POWER_WARNING

CFP Lane 13 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_HIGH_BIAS_WARNING

CFP Lane 14 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_HIGH_RX_POWER_WARNING

CFP Lane 14 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_HIGH_TEMP_WARNING

CFP Lane 14 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_14_HIGH_TX_POWER_WARNING

CFP Lane 14 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_LOW_BIAS_WARNING

CFP Lane 14 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_LOW_RX_POWER_WARNING

CFP Lane 14 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_14_LOW_TEMP_WARNING

CFP Lane 14 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_14_LOW_TX_POWER_WARNING

CFP Lane 14 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_HIGH_BIAS_WARNING

CFP Lane 15 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_HIGH_RX_POWER_WARNING

CFP Lane 15 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_HIGH_TEMP_WARNING

CFP Lane 15 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_15_HIGH_TX_POWER_WARNING

CFP Lane 15 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_LOW_BIAS_WARNING

CFP Lane 15 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_LOW_RX_POWER_WARNING

CFP Lane 15 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_15_LOW_TEMP_WARNING

CFP Lane 15 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_15_LOW_TX_POWER_WARNING

CFP Lane 15 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_HIGH_BIAS_WARNING

CFP Lane 2 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_HIGH_RX_POWER_WARNING

CFP Lane 2 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_HIGH_TEMP_WARNING

CFP Lane 2 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_2_HIGH_TX_POWER_WARNING

CFP Lane 2 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_LOW_BIAS_WARNING

CFP Lane 2 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_LOW_RX_POWER_WARNING

CFP Lane 2 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_2_LOW_TEMP_WARNING

CFP Lane 2 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_2_LOW_TX_POWER_WARNING

CFP Lane 2 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_HIGH_BIAS_WARNING

CFP Lane 3 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_HIGH_RX_POWER_WARNING

CFP Lane 3 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_HIGH_TEMP_WARNING

CFP Lane 3 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_3_HIGH_TX_POWER_WARNING

CFP Lane 3 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_LOW_BIAS_WARNING

CFP Lane 3 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_LOW_RX_POWER_WARNING

CFP Lane 3 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_3_LOW_TEMP_WARNING

CFP Lane 3 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_3_LOW_TX_POWER_WARNING

CFP Lane 3 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_HIGH_BIAS_WARNING

CFP Lane 4 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_HIGH_RX_POWER_WARNING

CFP Lane 4 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_HIGH_TEMP_WARNING

CFP Lane 4 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_4_HIGH_TX_POWER_WARNING

CFP Lane 4 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_LOW_BIAS_WARNING

CFP Lane 4 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_LOW_RX_POWER_WARNING

CFP Lane 4 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_4_LOW_TEMP_WARNING

CFP Lane 4 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_4_LOW_TX_POWER_WARNING

CFP Lane 4 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_HIGH_BIAS_WARNING

CFP Lane 5 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_HIGH_RX_POWER_WARNING

CFP Lane 5 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_HIGH_TEMP_WARNING

CFP Lane 5 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_5_HIGH_TX_POWER_WARNING

CFP Lane 5 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_LOW_BIAS_WARNING

CFP Lane 5 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_LOW_RX_POWER_WARNING

CFP Lane 5 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_5_LOW_TEMP_WARNING

CFP Lane 5 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_5_LOW_TX_POWER_WARNING

CFP Lane 5 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_HIGH_BIAS_WARNING

CFP Lane 6 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_HIGH_RX_POWER_WARNING

CFP Lane 6 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_HIGH_TEMP_WARNING

CFP Lane 6 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_6_HIGH_TX_POWER_WARNING

CFP Lane 6 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_LOW_BIAS_WARNING

CFP Lane 6 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_LOW_RX_POWER_WARNING

CFP Lane 6 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_6_LOW_TEMP_WARNING

CFP Lane 6 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_6_LOW_TX_POWER_WARNING

CFP Lane 6 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_HIGH_BIAS_WARNING

CFP Lane 7 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_HIGH_RX_POWER_WARNING

CFP Lane 7 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_HIGH_TEMP_WARNING

CFP Lane 7 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_7_HIGH_TX_POWER_WARNING

CFP Lane 7 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_LOW_BIAS_WARNING

CFP Lane 7 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_LOW_RX_POWER_WARNING

CFP Lane 7 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_7_LOW_TEMP_WARNING

CFP Lane 7 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_7_LOW_TX_POWER_WARNING

CFP Lane 7 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_HIGH_BIAS_WARNING

CFP Lane 8 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_HIGH_RX_POWER_WARNING

CFP Lane 8 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_HIGH_TEMP_WARNING

CFP Lane 8 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_8_HIGH_TX_POWER_WARNING

CFP Lane 8 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_LOW_BIAS_WARNING

CFP Lane 8 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_LOW_RX_POWER_WARNING

CFP Lane 8 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_8_LOW_TEMP_WARNING

CFP Lane 8 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_8_LOW_TX_POWER_WARNING

CFP Lane 8 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_HIGH_BIAS_WARNING

CFP Lane 9 High Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_HIGH_RX_POWER_WARNING

CFP Lane 9 High Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power greater than or equal to the high Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. Verify that the input signal has the necessary attenuation. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_HIGH_TEMP_WARNING

CFP Lane 9 High Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_9_HIGH_TX_POWER_WARNING

CFP Lane 9 High Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_LOW_BIAS_WARNING

CFP Lane 9 Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP laser bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_LOW_RX_POWER_WARNING

CFP Lane 9 Low Rx Power Warning

Explanation Environmental monitoring has detected a CFP Rx power less than or equal to the low Rx power warning threshold. The CFP is the pluggable optics on the line cards. The Rx power threshold values are read from the CFP.

Recommended Action Verify the following - device is properly inserted. - the RX fiber is inserted properly - the far end is enabled and transmitting - that input attnuation is not too high If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LANE_9_LOW_TEMP_WARNING

CFP Lane 9 Low Temperature Warning

Explanation Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LANE_9_LOW_TX_POWER_WARNING

CFP Lane 9 Low Tx Power Warning

Explanation Environmental monitoring has detected a CFP Tx power less than or equal to the low Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LOW_BIAS_WARNING

CFP Low Laser Bias Warning

Explanation Environmental monitoring has detected a CFP case bias less than or equal to the low laser bias warning threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

Error Message %PLATFORM-CFP-3-LOW_TEMP_WARNING

CFP Case Low Temperature Warning

Explanation Environmental monitoring has detected an CFP case temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’ - ’show environment temperatures’

Error Message %PLATFORM-CFP-3-LOW_VOLTAGE_WARNING

CFP Case Low Voltage Warning

Explanation Environmental monitoring has detected a CFP case voltage less than or equal to the low voltage warning threshold. The CFP is the pluggable optics on the line cards. The voltage threshold values are read from the CFP.

Recommended Action Verify that the device is properly inserted. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands - ’show controller i/f phy’ - ’show controller i/f internal’

CGV6_SERVICES Messages

Error Message %PLATFORM-CGV6_SERVICES-2-ERR_CGV6_SERVICES_INIT

[chars] [hex]

Explanation An error occurred in initialization of CGV6 Services. If this occurred during process startup or RP Switchover, then the process may be restarted.

Recommended Action Restart the cgv6_services process (process restart cgv6_services location) If the issue persists, do a cold reboot Services CGV6 MSC.If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CGV6_SERVICES-3-ERROR

error: [chars]: [chars]: [hex]

Explanation A fatal error occurred in the cgv6 services process which involves exiting the process.

Recommended Action collect the info from ’show diag’, ’show platform’, ’show inv’ If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CGV6_SERVICES-6-INFO

[chars]

Explanation This is a debug message in the CGV6 SERVICE PROCESS to indicate anomolies which are not FATAL. Some of the messages may indicate a failure to allocate resources needed by applications. In many cases these messages must not keep appearing after the temperory situation is resolved.

Recommended Action ’show logging’ to confirm sysdb errors

Error Message %PLATFORM-CGV6_SERVICES-7-DEBUG

[chars]: [chars] errno [dec]

Explanation This is a debug message in the CGV6 SERVICES PROCESS to indicate anomolies which are not FATAL. Some of the messages may indicate a failure to allocate resources needed by applications. In many cases these messages must not keep appearing after the temperory situation is resolved.

Recommended Action ’show logging’ to confirm sysdb errors

Error Message %PLATFORM-CGV6_SERVICES-7-GENERIC_ERROR

[chars] [hex]

Explanation A generic error occurred in Services CGV6 SERVICE. Cause of the error will be mentioned in the message displayed.

Recommended Action No action is required.

Error Message %PLATFORM-CGV6_SERVICES-7-GENERIC_INFO

Info: [chars]

Explanation The message is used to report generic info about Services CGV6 SERVICES.

Recommended Action *NONE*

CHP Messages

Error Message %PLATFORM-CHP-0-FAULT_RECOVERY_ERR

The fault recovery procedure for the ToFab component of the fabric driver has failed. The root fault was: [chars]

Explanation When a hardware fault occurs and the device driver cannot correct it, the Platform Manager is required to reset the ASICs. This error indicates that the Platform Manager failed to reset the ASICs and the hardware on the PRP may not be in an operational state. This condition affects the functionality of the entire router. %s is the Interrupt Source.

Recommended Action If the system has not failed over automatically and a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0 ’ where x is the slot of route processor that generated the error. If no redundant RP is configured you will need to reboot the router by issuing the reload command. Call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-CRC_ERR

chopper dll: block: [chars], entity: [chars] had CRC error, count: [dec]

Explanation PII block got a packet from the entity mentioned above with a CRC error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-DEVICE_HALT

TFQ: device halted, sub-block: [chars], halted entity: [chars]

Explanation TFQ, ASIC got halted. The halted block and its parent block are provided

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-DMA_ERR

Chopper detected a DMA error: Data [hex]

Explanation This message indicates that the Chopper hardware found a DMA problem. The hexadecimal data indicates the error register value when the problem is detected. This usually indicates a hardware error.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-FATAL

chopper dll: fatal error encountered, reason equals [chars]

Explanation iqm, chopper dll manager encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-FATAL_2

chopper dll: fatal error encountered, reason equals [chars], errno equals [dec]

Explanation chopper encountered a fatal error and is not able to recover from the error. A reason text will be supplied call support with this text. An integer errno will also be printed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-FUSILLI_PARITY_ERR

Chopper detected a Fusilli parity error: Data [hex]

Explanation A parity error has been detected on the Chopper to Fusilli interface. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP. RP may be reset.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-GEN_INFO

chopper dll: general information,[chars]

Explanation The CHP’s informational message.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-HWINIT_INCOMPLETE

chopper dll: hardware initialization not complete

Explanation hardware init is not complete.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-INFO

chopper dll: service degrading error, reason equals [chars]

Explanation The chopper encountered an error that would lead to degraded service.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-INTR_ENABLE_FAIL

chopper dll: intr enable at addr: [hex] mask: [hex] failed.

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-INTR_STATUS_GET_ERR

chopper dll: intr status get failed for: [chars]@[hex], rc equals [dec]

Explanation Hardware register read failed.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-MALLOC_FAILED

chopper dll: fatal memory allocation error for [dec] bytes

Explanation CHP encountered a fatal memory allocation error

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-NOT_AVAILABLE

chopper dll: asic is not available

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-NOT_OPERATIONAL

chopper dll: asic is not operational, state: [dec]

Explanation hardware state is not correct.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-3-NOT_YET_IMPLEMENTED

chopper dll: this function [chars] is not yet implemented

Explanation TFQ, chopper dll, a function is not implemented.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-PCI_ERR

Chopper detected a PCI error: Data [hex]

Explanation A PCI error has been detected by the Chopper PCI interface. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP. RP may be reset.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-3-SRAM_PARITY_ERR

Chopper detected a SRAM parity error: Data [hex]

Explanation A parity error has been detected on the Chopper to SRAM interface. The hex number indicates the error cause register value. This usually indicates a hardware problem on the RP. RP may be reset.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CHP-6-UNHANDLED_HALT

chopper dll: halt not handled, parent: [chars], child: [chars], intr: [dec]

Explanation Hardware halt is not handled.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CHP-6-UNHANDLED_INTR

chopper dll: intr not handled, parent: [chars], child: [chars], group id: [dec], intr: [dec]

Explanation Hardware interrupt is not handled in the code, need to implement.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

CIH Messages

Error Message %PLATFORM-CIH-0-ASIC_ERROR_BOARD_RELOAD

[chars][[dec]]: reload board due to too many reset

Explanation Mulitple reset occurred, need to reload board

Recommended Action Due to too many reset, board has been reloaded to recover *None*

Error Message %PLATFORM-CIH-0-ASIC_ERROR_RELOAD_SYS

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need to reload system

Recommended Action An error has happened and need to reload the system. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-0-ASIC_ERROR_SHUTDOWN_BOARD

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and board need shutdown.

Recommended Action An error has happened and board is shutdown. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and been handled.

Recommended Action *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_HARD_RESET

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need a hard reset.

Recommended Action An error has happen and HARD reset has been performed to recover. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_PON_RESET

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need a power on reset.

Recommended Action An error has happen and PON reset has been performed to recover. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_REPROG_RESOURCE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need reprogram resource.

Recommended Action An error that causes reprogram resource has happened and been handled *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_REPROG_RESOURCE_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors need to reprogram resource have happened, such errors has crossed threshold.

Recommended Action Errors that cause reprogram resource have happened and exceeded threshold. The error condition has been handled. *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_RETRAIN_LINK

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause retrain link.

Recommended Action An error that causes retrain link has happened and been handled *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_SCRUB_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors have occured and need memory scrubbing, such errors have crossed threshold.

Recommended Action Errors have been handled. *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_SHUTDOWN_LINK_FABRIC

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause fabric link shutdown.

Recommended Action An error that causeis fabric link shutdown has happened and been handled *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_SHUTDOWN_LINK_ILITE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause ilte link shutdown.

Recommended Action An error that causes ilite link shutdown has happened and been handled *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_SPECIAL_HANDLE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and been handled.

Recommended Action *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_SPECIAL_HANDLE_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors have occured and been handled. Such errors have crossed threshold.

Recommended Action ASIC errors that need special handling have occured and exceed the threshold. The error condition has been handled *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_PERSIST_THRESHOLD

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error threshold was crossed.

Recommended Action *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_RELOAD_BOARD

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need to reload board

Recommended Action An error has happened and board is reloaded. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_REQUEST_RELOAD_BOARD

[chars][[dec]]: device is not recovered from fault - and reload is requested.

Explanation An ASIC error has occured and cause board reload.

Recommended Action The output message is warning board reload request. *None*

Error Message %PLATFORM-CIH-1-ASIC_ERROR_SHUTDOWN_LINK_ILITE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause ilte link shutdown.

Recommended Action An error that causes ilite link shutdown has happened and been handled *None*

Error Message %PLATFORM-CIH-2-ASIC_ERROR_HARD_RESET

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and hard reset is needed.

Recommended Action An error has happened and HARD reset has been performed to recover. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-2-ASIC_ERROR_PON_RESET

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and power on reset is needed

Recommended Action An error has happen and PON reset has been performed to recover. Collect required information and contact TAC *None*

Error Message %PLATFORM-CIH-3-ASIC_ERROR_SHUTDOWN_LINK_FABRIC

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause fabric link shutdown.

Recommended Action An error that causes fabric link shutdown has happened and been handled *None*

Error Message %PLATFORM-CIH-3-ASIC_ERROR_SPECIAL_HANDLE_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors have occured and been handled. Such error have crossed threshold.

Recommended Action ASIC errors that need special handling have occured and exceed the threshold. The error condition has been handled. *None*

Error Message %PLATFORM-CIH-3-COMMON_ERROR

[chars]

Explanation The CIH library encountered an error related to memory or data value.

Recommended Action An error would be reported to the client application which should handle this condition appropriately. *None*

Error Message %PLATFORM-CIH-3-MISS_MEM_INFO

Leaf node [chars] do not have mem info

Explanation Missing mem_info while processing error interrupt.

Recommended Action Error at the memory location will not be corrected in this case. Need add this information to parser generated file *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and been handled.

Recommended Action *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_ASIC_SCAN

ASIC SCAN is needed due to ASIC error [hex] with instance [dec]

Explanation An ASIC error which requires ASIC SCAN has occured, the ASIC SCAN will be triggered.

Recommended Action The linecard will be booted after the ASIC SCAN is completed, save the ASIC SCAN output files on the linecard local disk, provide the files to TAC support for further debugging. *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_HARD_RESET_START

[chars][[dec]]: HARD_RESET needed [hex]

Explanation An ASIC error has occured and need to hard reset, this marks the beginning of it.

Recommended Action *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_PON_RESET_START

[chars][[dec]]: PON_RESET needed [hex]

Explanation An ASIC error has occured and need power on reset, this mark the beginning of it.

Recommended Action *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_REPROG_RESOURCE_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause reprogram resource, such error has crossed threshold.

Recommended Action Errors that cause reprogram resource have happened and exceed threshold. This has been handled. *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_RETRAIN_LINK

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and cause retrain link.

Recommended Action An error that causes retrain link has happened and been handled *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_SCRUB_THRESH

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors have occured and need memory scrubbing, such errors have crossed threshold.

Recommended Action Errors have been handled. *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_SPECIAL_HANDLE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error that need special handling has occured and been handled.

Recommended Action *None*

Error Message %PLATFORM-CIH-5-ASIC_ERROR_THRESHOLD

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation ASIC errors have exceed the threshold.

Recommended Action *None*

Error Message %PLATFORM-CIH-7-ASIC_ERROR_REPROG_RESOURCE

[chars][[dec]]: [chars] error has occurred[chars]%s [hex] [chars] [chars]

Explanation An ASIC error has occured and need to reprogram resource.

Recommended Action An error that causes reprogram resource has happened and been handled *None*

CLKCTRL_T Messages

Error Message %PLATFORM-CLKCTRL_T-2-DEV_VERSION_ERROR

Timing driver version is not compatible with the hardware FPGA version. S/W ver: [dec]:[dec] H/W ver: [dec]:[dec]

Explanation Timing driver software version is not compatible with the hardware FPGA version.

Recommended Action Upgrade the ClkCtrl Timing FPGA image using the FPD procedure. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-2-EEPROM_OVERCURRENT

ClkCtrl detected an EEPROM overcurrent condition

Explanation ClkCtrl detected an EEPROM overcurrent condition

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-2-PARITY_ERROR

Timing software detected a parity error address equals [dec] data equals [dec]

Explanation Timing software detected a parity error from interrupt controller

Recommended Action If a redundant RSP card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’. 2 - reload the RSP card that failed with the ’reload location’ command in admin mode. If no redundant RSP is configured, you will need to reboot the router by issuing the above reload command. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-INVALID_64K_INPUT_SYNC_0

Invalid signal received for Rx mode [chars] on sync [dec] clock-interface

Explanation The 64k composite clock signal has been invalidated possibly due to loss-of-signal condition or AMI violations.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 64kHz + 8kHz Japanese timing signal(defined in G.703 Appendix II.1) is applied at input port.

Error Message %PLATFORM-CLKCTRL_T-3-INVALID_64K_INPUT_SYNC_1

Invalid signal received for Rx mode [chars] on sync [dec] clock-interface

Explanation The 64k composite clock signal has been invalidated possibly due to loss-of-signal condition or AMI violations.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 64kHz + 8kHz Japanese timing signal(defined in G.703 Appendix II.1) is applied at input port.

Error Message %PLATFORM-CLKCTRL_T-3-PLL_T0_STATE_FREERUN

The clock-control T0 PLL (reference clock for all interfaces) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL_T-3-PLL_T0_STATE_HOLDOVER

The clock-control T0 PLL (reference clock for all interfaces) is [chars] HOLDOVER mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is in holdover, maintaining the most-recent frequency to which it was locked.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL_T-3-PLL_T4_STATE_FREERUN

The clock-control T4 PLL (reference clock for Sync 0 and Sync 1 ports) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T4 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_AIS_SYNC_0

Alarm indication signal condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected AIS defect for incoming signal. AIS is usually an unframed all-ones signal. For T1 mode AIS is declared when the BITS receiver detects four or fewer zeroes in a 3ms period. For E1 mode AIS is declared when the BITS receiver detects fewer than three zeroes in two E1 frames.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Trace and check the source of AIS signal. Possibly an incorrect internal configuration in the service provider equipment, or a failure in their upstream connections.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_AIS_SYNC_1

Alarm indication signal condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected AIS defect for incoming signal. AIS is usually an unframed all-ones signal. For T1 mode AIS is declared when the BITS receiver detects four or fewer zeroes in a 3ms period. For E1 mode AIS is declared when the BITS receiver detects fewer than three zeroes in two E1 frames.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Trace and check the source of AIS signal. Possibly an incorrect internal configuration in the service provider equipment, or a failure in their upstream connections.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_FRAME_ERR_SYNC_0

Frame error rate exceeded condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation For UTI mode alarm is raised if frame error rate exceeds 2%.

Recommended Action 1) Ensure valid BITS/UTI signal is applied at input port.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_FRAME_ERR_SYNC_1

Frame error rate exceeded condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation For UTI mode alarm is raised if frame error rate exceeds 2%.

Recommended Action 1) Ensure valid BITS/UTI signal is applied at input port.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_INVALID_10M_CLOCK_SYNC_2

Invalid 10MHz input clock observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The 10MHz UTC clock signal has been invalidated possibly due to loss-of-signal condition, offset out of range or phase lock issue.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 10MHz clock is applied at input port.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_LOF_SYNC_0

Loss of frame condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected OOF defect for incoming signal. For T1 mode OOF is declared when out of every four frame bits two or more frame bits are received in error. For E1 mode OOF is declared when three consecutive incorrect FAS is received. Also for E1 mode(CRC-4 framing) OOF can be declared when 915 or more CRC blocks out of 1000 are received in error. Additionally for E1 mode(CAS signalling) OOF can be declared when two consecutive multiframe alignment words are received in error or, for a period of one multiframe, all bits in timeslot 16 are zero.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Configure to other framing format to check if error clears.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_LOF_SYNC_1

Loss of frame condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected OOF defect for incoming signal. For T1 mode OOF is declared when out of every four frame bits two or more frame bits are received in error. For E1 mode OOF is declared when three consecutive incorrect FAS is received. Also for E1 mode(CRC-4 framing) OOF can be declared when 915 or more CRC blocks out of 1000 are received in error. Additionally for E1 mode(CAS signalling) OOF can be declared when two consecutive multiframe alignment words are received in error or, for a period of one multiframe, all bits in timeslot 16 are zero.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Configure to other framing format to check if error clears.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_LOS_SYNC_0

Loss of signal condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation For T1 mode LOS is declared (as detected by BITS receiver) when no pulses are detected in a window of 192 consecutive pulse intervals. In E1 and 2048kHz modes LOS is declared when no pulses are detected in a window of 255 consecutive pulse intervals. For UTI mode, LOS is detected by hardware as per J.211 specifications.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Check the cable integrity and cable connectors. The receive pair should be on pins 1,2 on the RJ-45 jack.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_LOS_SYNC_1

Loss of signal condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation For T1 mode LOS is declared (as detected by BITS receiver) when no pulses are detected in a window of 192 consecutive pulse intervals. In E1 and 2048kHz modes LOS is declared when no pulses are detected in a window of 255 consecutive pulse intervals. For UTI mode, LOS is detected by hardware as per J.211 specifications.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Check the cable integrity and cable connectors. The receive pair should be on pins 1,2 on the RJ-45 jack.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_NO_SATELLITE_AVAILABLE_SYNC_2

The specified [chars] TOD message received at input port indicates no satellite availability for sync [dec] clock-interface

Explanation The received and parsed GPS TOD message frame from external equipment indicates no satellite availablity, which could possibly indicate that the time-of-day received is not synchronized to a UTC/TAI timescale.

Recommended Action 1) Ensure GPS receiver connectivity on the external equipment.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_NO_TOD_MSG_SYNC_2

No TOD messages in the specified [chars] format are received on sync [dec] clock-interface

Explanation No TOD messages are being detected on the GPS port UART receiver.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_RAI_SYNC_0

Remote alarm indication condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected RAI defect for incoming signal. Receiving remote alarm indication(RAI) means the far-end equipment over the T1/E1 line has a problem with the signal it is receiving from the upstream equipment.

Recommended Action Verify input BITS clock signal is set up correctly.

Error Message %PLATFORM-CLKCTRL_T-3-RX_ALARM_RAI_SYNC_1

Remote alarm indication condition observed for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected RAI defect for incoming signal. Receiving remote alarm indication(RAI) means the far-end equipment over the T1/E1 line has a problem with the signal it is receiving from the upstream equipment.

Recommended Action Verify input BITS clock signal is set up correctly.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_OC_SYNC_0

Transmit open circuit condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation BITS transmitter has detected an open circuit condition.

Recommended Action Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_OC_SYNC_1

Transmit open circuit condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation BITS transmitter has detected an open circuit condition.

Recommended Action Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_SC_SYNC_0

Transmit short circuit condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation Condition raised by BITS transmitter when internal short-circuit resistance is approx 25 ohms or less.

Recommended Action None.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_SC_SYNC_1

Transmit short circuit condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation Condition raised by BITS transmitter when internal short-circuit resistance is approx 25 ohms or less.

Recommended Action None.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TAF_SYNC_0

Incorrect frame alignment condition observed for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TAF_SYNC_1

Incorrect frame alignment condition observed for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TMF_SYNC_0

Incorrect multi-frame alignment condition observed for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TMF_SYNC_1

Incorrect multi-frame alignment condition observed for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TPDV_SYNC_0

Transmit pulse density violation condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation In T1 mode TPDV alarm is raised when the transmit data stream does not meet ANSI T1.403 requirements for transmit pulse density.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL_T-3-TX_ALARM_TPDV_SYNC_1

Transmit pulse density violation condition observed for Tx mode [chars] on sync [dec] clock-interface

Explanation In T1 mode TPDV alarm is raised when the transmit data stream does not meet ANSI T1.403 requirements for transmit pulse density.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CLKCTRL Messages

Error Message %PLATFORM-CLKCTRL-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation ClkCtrl Driver encountered a fatal error and is not able to recover. The supplied text string will explain the reason. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation ClkCtrl Driver encountered a fatal error and is not able to recover. The supplied text string will explain the reason. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation ClkCtrl Driver encountered a fatal error and is not able to recover. The supplied text string will explain the reason. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation ClkCtrl encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation ClkCtrl encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation ClkCtrl encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-INVALID_10M_CLOCK

Alarm [chars]. Invalid 10MHz input clock received for Rx mode [chars] on sync [dec] clock-interface

Explanation The 10MHz UTC clock signal has been invalidated possibly due to loss-of-signal condition, offset out of range or phase lock issue.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 10MHz clock is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-INVALID_10M_CLOCK

Alarm [chars]. Invalid 10MHz input clock received for Rx mode [chars] on sync [dec] clock-interface

Explanation The 10MHz UTC clock signal has been invalidated possibly due to loss-of-signal condition, offset out of range or phase lock issue.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 10MHz clock is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-INVALID_64K_INPUT

Invalid signal [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The 64k composite clock signal has been invalidated possibly due to loss-of-signal condition or AMI violations.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 64kHz + 8kHz Japanese timing signal(defined in G.703 Appendix II.1) is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-INVALID_64K_INPUT

Invalid signal [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The 64k composite clock signal has been invalidated possibly due to loss-of-signal condition or AMI violations.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 64kHz + 8kHz Japanese timing signal(defined in G.703 Appendix II.1) is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-INVALID_64K_INPUT

Invalid signal [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The 64k composite clock signal has been invalidated possibly due to loss-of-signal condition or AMI violations.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Ensure valid 64kHz + 8kHz Japanese timing signal(defined in G.703 Appendix II.1) is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-NO_SATELLITE_AVAILABLE

Alarm [chars]. The specified [chars] TOD message received at input port inidicates no satellite availability for sync [dec] clock-interface

Explanation The received and parsed GPS TOD message frame from external equipment indicates no satellite availablity, which could possibly indicate that the time-of-day received is not synchronized to a UTC/TAI timescale.

Recommended Action 1) Ensure GPS receiver connectivity on the external equipment.

Error Message %PLATFORM-CLKCTRL-3-NO_SATELLITE_AVAILABLE

Alarm [chars]. The specified [chars] TOD message received at input port inidicates no satellite availability for sync [dec] clock-interface

Explanation The received and parsed GPS TOD message frame from external equipment indicates no satellite availablity, which could possibly indicate that the time-of-day received is not synchronized to a UTC/TAI timescale.

Recommended Action 1) Ensure GPS receiver connectivity on the external equipment.

Error Message %PLATFORM-CLKCTRL-3-NO_TOD_MSG

Alarm [chars]. No TOD messages in the specified [chars] format are received on sync [dec] clock-interface

Explanation No TOD messages are being detected on the GPS port UART receiver.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL-3-NO_TOD_MSG

Alarm [chars]. No TOD messages in the specified [chars] format are received on sync [dec] clock-interface

Explanation No TOD messages are being detected on the GPS port UART receiver.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_AIS

Alarm indication signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected AIS defect for incoming signal. AIS is usually an unframed all-ones signal. For T1 mode AIS is declared when the BITS receiver detects four or fewer zeroes in a 3ms period. For E1 mode AIS is declared when the BITS receiver detects fewer than three zeroes in two E1 frames.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Trace and check the source of AIS signal. Possibly an incorrect internal configuration in the service provider equipment, or a failure in their upstream connections.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_AIS

Alarm indication signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected AIS defect for incoming signal. AIS is usually an unframed all-ones signal. For T1 mode AIS is declared when the BITS receiver detects four or fewer zeroes in a 3ms period. For E1 mode AIS is declared when the BITS receiver detects fewer than three zeroes in two E1 frames.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Trace and check the source of AIS signal. Possibly an incorrect internal configuration in the service provider equipment, or a failure in their upstream connections.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_AIS

Alarm indication signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected AIS defect for incoming signal. AIS is usually an unframed all-ones signal. For T1 mode AIS is declared when the BITS receiver detects four or fewer zeroes in a 3ms period. For E1 mode AIS is declared when the BITS receiver detects fewer than three zeroes in two E1 frames.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Trace and check the source of AIS signal. Possibly an incorrect internal configuration in the service provider equipment, or a failure in their upstream connections.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_FRAME_ERR

Frame error rate exceeded condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For UTI mode alarm is raised if frame error rate exceeds 2%.

Recommended Action 1) Ensure valid BITS/UTI signal is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_FRAME_ERR

Frame error rate exceeded condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For UTI mode alarm is raised if frame error rate exceeds 2%.

Recommended Action 1) Ensure valid BITS/UTI signal is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_FRAME_ERR

Frame error rate exceeded condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For UTI mode alarm is raised if frame error rate exceeds 2%.

Recommended Action 1) Ensure valid BITS/UTI signal is applied at input port.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOF

Loss of frame condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected OOF defect for incoming signal. For T1 mode OOF is declared when out of every four frame bits two or more frame bits are received in error. For E1 mode OOF is declared when three consecutive incorrect FAS is received. Also for E1 mode(CRC-4 framing) OOF can be declared when 915 or more CRC blocks out of 1000 are received in error. Additionally for E1 mode(CAS signalling) OOF can be declared when two consecutive multiframe alignment words are received in error or, for a period of one multiframe, all bits in timeslot 16 are zero.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Configure to other framing format to check if error clears.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOF

Loss of frame condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected OOF defect for incoming signal. For T1 mode OOF is declared when out of every four frame bits two or more frame bits are received in error. For E1 mode OOF is declared when three consecutive incorrect FAS is received. Also for E1 mode(CRC-4 framing) OOF can be declared when 915 or more CRC blocks out of 1000 are received in error. Additionally for E1 mode(CAS signalling) OOF can be declared when two consecutive multiframe alignment words are received in error or, for a period of one multiframe, all bits in timeslot 16 are zero.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Configure to other framing format to check if error clears.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOF

Loss of frame condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected OOF defect for incoming signal. For T1 mode OOF is declared when out of every four frame bits two or more frame bits are received in error. For E1 mode OOF is declared when three consecutive incorrect FAS is received. Also for E1 mode(CRC-4 framing) OOF can be declared when 915 or more CRC blocks out of 1000 are received in error. Additionally for E1 mode(CAS signalling) OOF can be declared when two consecutive multiframe alignment words are received in error or, for a period of one multiframe, all bits in timeslot 16 are zero.

Recommended Action 1) Ensure framing format on port matches framing format on the line. 2) Configure to other framing format to check if error clears.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOS

Loss of signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For T1 mode LOS is declared (as detected by BITS receiver) when no pulses are detected in a window of 192 consecutive pulse intervals. In E1 and 2048kHz modes LOS is declared when no pulses are detected in a window of 255 consecutive pulse intervals. For UTI mode, LOS is detected by hardware as per J.211 specifications.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Check the cable integrity and cable connectors. The receive pair should be on pins 1,2 on the RJ-45 jack.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOS

Loss of signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For T1 mode LOS is declared (as detected by BITS receiver) when no pulses are detected in a window of 192 consecutive pulse intervals. In E1 and 2048kHz modes LOS is declared when no pulses are detected in a window of 255 consecutive pulse intervals. For UTI mode, LOS is detected by hardware as per J.211 specifications.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Check the cable integrity and cable connectors. The receive pair should be on pins 1,2 on the RJ-45 jack.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_LOS

Loss of signal condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation For T1 mode LOS is declared (as detected by BITS receiver) when no pulses are detected in a window of 192 consecutive pulse intervals. In E1 and 2048kHz modes LOS is declared when no pulses are detected in a window of 255 consecutive pulse intervals. For UTI mode, LOS is detected by hardware as per J.211 specifications.

Recommended Action 1) Ensure cable connection between the configured interface port and external equipment. 2) Check the cable integrity and cable connectors. The receive pair should be on pins 1,2 on the RJ-45 jack.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_RAI

Remote alarm indication condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected RAI defect for incoming signal. Receiving remote alarm indication(RAI) means the far-end equipment over the T1/E1 line has a problem with the signal it is receiving from the upstream equipment.

Recommended Action Verify input BITS clock signal is set up correctly.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_RAI

Remote alarm indication condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected RAI defect for incoming signal. Receiving remote alarm indication(RAI) means the far-end equipment over the T1/E1 line has a problem with the signal it is receiving from the upstream equipment.

Recommended Action Verify input BITS clock signal is set up correctly.

Error Message %PLATFORM-CLKCTRL-3-RX_ALARM_RAI

Remote alarm indication condition [chars] for Rx mode [chars] on sync [dec] clock-interface

Explanation The BITS receiver has detected RAI defect for incoming signal. Receiving remote alarm indication(RAI) means the far-end equipment over the T1/E1 line has a problem with the signal it is receiving from the upstream equipment.

Recommended Action Verify input BITS clock signal is set up correctly.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_OC

Transmit open circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation BITS transmitter has detected an open circuit condition.

Recommended Action Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_OC

Transmit open circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation BITS transmitter has detected an open circuit condition.

Recommended Action Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_OC

Transmit open circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation BITS transmitter has detected an open circuit condition.

Recommended Action Ensure cable connection between the configured interface port and external equipment.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_SC

Transmit short circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation Condition raised by BITS transmitter when internal short-circuit resistance is approx 25 ohms or less.

Recommended Action None.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_SC

Transmit short circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation Condition raised by BITS transmitter when internal short-circuit resistance is approx 25 ohms or less.

Recommended Action None.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_SC

Transmit short circuit condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation Condition raised by BITS transmitter when internal short-circuit resistance is approx 25 ohms or less.

Recommended Action None.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TAF

Incorrect frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TAF

Incorrect frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TAF

Incorrect frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TMF

Incorrect multi-frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TMF

Incorrect multi-frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TMF

Incorrect multi-frame alignment condition [chars] for Tx mode [chars] on sync [dec] clock-interface.

Explanation Condition raised possibly due to incorrect internal BITS transmitter configuration.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TPDV

Transmit pulse density violation condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation In T1 mode TPDV alarm is raised when the transmit data stream does not meet ANSI T1.403 requirements for transmit pulse density.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TPDV

Transmit pulse density violation condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation In T1 mode TPDV alarm is raised when the transmit data stream does not meet ANSI T1.403 requirements for transmit pulse density.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-3-TX_ALARM_TPDV

Transmit pulse density violation condition [chars] for Tx mode [chars] on sync [dec] clock-interface

Explanation In T1 mode TPDV alarm is raised when the transmit data stream does not meet ANSI T1.403 requirements for transmit pulse density.

Recommended Action Re-configure and verify if condition is cleared. If the problem persists, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the ClkCtrl_driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the ClkCtrl_driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the ClkCtrl_driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_FREERUN

The clock-control T0 PLL (reference clock for all interfaces) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_FREERUN

The clock-control T0 PLL (reference clock for all interfaces) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_FREERUN

The clock-control T0 PLL (reference clock for all interfaces) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_HOLDOVER

The clock-control T0 PLL (reference clock for all interfaces) is [chars] HOLDOVER mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is in holdover, maintaining the most-recent frequency to which it was locked.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_HOLDOVER

The clock-control T0 PLL (reference clock for all interfaces) is [chars] HOLDOVER mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is in holdover, maintaining the most-recent frequency to which it was locked.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T0_STATE_HOLDOVER

The clock-control T0 PLL (reference clock for all interfaces) is [chars] HOLDOVER mode.

Explanation No external reference frequency is available for synchronization, so the T0 PLL output is in holdover, maintaining the most-recent frequency to which it was locked.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T4_STATE_FREERUN

The clock-control T4 PLL (reference clock for Sync 0 and Sync 1 ports) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T4 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T4_STATE_FREERUN

The clock-control T4 PLL (reference clock for Sync 0 and Sync 1 ports) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T4 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-5-PLL_T4_STATE_FREERUN

The clock-control T4 PLL (reference clock for Sync 0 and Sync 1 ports) is [chars] FREERUN mode.

Explanation No external reference frequency is available for synchronization, so the T4 PLL output is free-running.

Recommended Action None. This is just a status indication.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation ClkCtrl Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in ClkCtrl Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in ClkCtrl Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in ClkCtrl Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation ClkCtrl Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation ClkCtrl Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation ClkCtrl Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation ClkCtrl LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation ClkCtrl LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLKCTRL-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation ClkCtrl LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CLUSTER_UPGRADE Messages

Error Message %PLATFORM-CLUSTER_UPGRADE-3-ERR_INIT

[chars] - error : [chars], exiting...

Explanation The cluster upgrade process failed in initialization. This indicates that there was a software error during initialization.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLUSTER_UPGRADE-3-ERR_MEM_ALLOC

Failed to allocate [dec] bytes, exiting...

Explanation The dsc process could not allocate memory. This indicates some problem with the system wide memory.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.’

Error Message %PLATFORM-CLUSTER_UPGRADE-3-FAILURE

[chars] [hex] [chars]

Explanation This message indicates that a failure has occured.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CLUSTER_UPGRADE-6-INFO

[chars]

Explanation This is an informational message from the Cluster Upgrade Engine

Recommended Action No action is required.

COMMON Messages

Error Message %PLATFORM-COMMON-0-LC_HEADLESS_ACT_RSP_HB_REQ_FAILURE

Headless RSP Detected: No HB requests from the active RSP.

Explanation This LC has timed out waiting for Heartbeat requests from the active RSP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-COMMON-0-RSP_HEADLESS_ACT_RSP_HB_REQ_FAILURE

Headless RSP Detected: No HB requests from the active RSP.

Explanation This RSP has timed out waiting for Heartbeat requests from the active RSP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CONCERTO Messages

Error Message %PLATFORM-CONCERTO-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation CONCERTO Driver encountered a fatal error and is not able to recover. The supplied text string will explain the reason. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation CONCERTO encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-5-ERR_CONT

Continuing execution: [chars]: Caused by [chars]

Explanation This message indicates an error occurred beyond which execution of the concerto_driver may continue, attempting to effect recovery or work-around internally, minimizing loss of information/functionality.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation CONCERTO Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation CONCERTO Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-7-ERR_EXIT

Exit on error: [chars]: Caused by [chars]

Explanation An error occurred in CONCERTO Driver which requires exiting (and, hence, restarting) the process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation CONCERTO Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CONCERTO-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation concerto LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CPU_CTRL Messages

Error Message %PLATFORM-CPU_CTRL-2-ERR

[chars] - [dec]: [chars]

Explanation Error in LAGUNA operation.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CPU_CTRL-2-ERR_RC

[chars] - [dec]: [chars] (rc equals [hex])

Explanation Error in LAGUNA operation.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %PLATFORM-CPU_CTRL-3-ACK_ERROR

i2c ack error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

Error Message %PLATFORM-CPU_CTRL-3-ACK_ERROR

i2c ack error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

Error Message %PLATFORM-CPU_CTRL-3-ACK_ERROR

i2c ack error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

Error Message %PLATFORM-CPU_CTRL-3-BACKUP_PARTITION

[chars] loaded from backup partition

Explanation The FPGA has loaded from backup partition. recommended_action: Upgrade FPGA using upgrade hw-module fpd command.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPU_CTRL-3-BACKUP_PARTITION

[chars] loaded from backup partition

Explanation The FPGA has loaded from backup partition. recommended_action: Upgrade FPGA using upgrade hw-module fpd command.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPU_CTRL-3-BACKUP_PARTITION

[chars] loaded from backup partition

Explanation The FPGA has loaded from backup partition.

Recommended Action Upgrade FPGA using upgrade hw-module fpd command.

Error Message %PLATFORM-CPU_CTRL-3-PROG_ERROR

[chars] programming error.

Explanation The system has encouncered an error while loading FPGA.

Recommended Action Upgrade FPGA using upgrade hw-module fpd command.

Error Message %PLATFORM-CPU_CTRL-3-PROG_ERROR

[chars] programming error.

Explanation The system has encouncered an error while loading FPGA. recommended_action: Upgrade FPGA using upgrade hw-module fpd command.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPU_CTRL-3-PROG_ERROR

[chars] programming error.

Explanation The system has encouncered an error while loading FPGA. recommended_action: Upgrade FPGA using upgrade hw-module fpd command.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPU_CTRL-3-TIMEOUT_ERROR

i2c timeout error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

Error Message %PLATFORM-CPU_CTRL-3-TIMEOUT_ERROR

i2c timeout error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

Error Message %PLATFORM-CPU_CTRL-3-TIMEOUT_ERROR

i2c timeout error on SFP+ port [dec].

Explanation The system has encouncered an error while refreshing SFP port.

Recommended Action replace SFP.

CPUCTRL_SIP700_DLL Messages

Error Message %PLATFORM-CPUCTRL_SIP700_DLL-0-INIT_ERROR

CPU Control, DLL initialization error, [chars]%s

Explanation The CPU Control, Dynamic Link Library (DLL) failed to initialize. The effect is that the line card may not function or may not function appropriately. The CPU Control DLL provides low level services to other components on the SIP 700 Line Card (LC). These include, among other things, interrupt services and watch dog time out services. If CPU Control services are not available then those mandatory processes that use these services will exit, respawn and retry the initialization. If these services remain unavailable then the LC will not properly boot and will reset itself. This error is generally indicative of a larger LC-wide problem. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action This error is unlikely to occur by itself nor is it likely to be the root cause of the problem. Please copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide the gathered information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700_DLL-3-CLEANUP_ERROR

CPU Control, DLL cleanup error, [chars]%s

Explanation The CPU Control, Dynamic Link Library (DLL) failed to cleanup. The effect is relatively minimal and should not be of concern in and of itself. Some minor resource may or may not have been properly returned to a system resource pool. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action Should this error occur repeatedly within the context of other system errors then copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide this information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700_DLL-3-TRACE_ERROR

CPU Control, DLL trace error, [chars]%s

Explanation The CPU Control, Dynamic Link Library (DLL) failed to initialize the LTrace facility. The effect is that the CPU Control debug trace facility is not functional. This means that trace information used by Cisco support to help isolate CPU Control device issues may not be available. This does not impact normal CPU Control device operations. Note that it is unlikely that this failure would occur by itself. This failure is generally indicative of a larger LC-wide problem. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action No action is required.

CPUCTRL_SIP700 Messages

Error Message %PLATFORM-CPUCTRL_SIP700-0-EVT_INIT_ERROR

CPU Control driver, event manager setup error, [chars]%s

Explanation The CPU Control driver failed to initialize the event manager. The effect is that the line card may not function or may not function appropriately. The CPU Control driver provides low level services on the SIP 700 Line Card (LC). These include, among other things, access timeout interrupt services and bus parity error interrupt services. The CPU Control driver relies on an event manager to communicate with other components on the SIP 700 LC. If event manager services are not available then the driver process is exited, respawned and the initialization retried. The CPU Control driver is a mandatory process. If the initialization continues to fail after several retries the LC will not properly boot and will reset itself. This error is generally indicative of a larger LC-wide problem. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action This error is unlikely to occur by itself nor is it likely to be the root cause of the problem. Please copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide the gathered information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700-0-INIT_ERROR

CPU Control driver, main setup error, [chars]%s

Explanation The CPU Control driver failed to initialize. The effect is that the line card may not function or may not function appropriately. The CPU Control driver provides low level services on the SIP 700 Line Card (LC). These include, among other things, access timeout interrupt services and bus parity error interrupt services. If these services are not available then the driver process is exited, respawned and the initialization retried. The CPU Control driver is a mandatory process. If the initialization continues to fail after several retries the LC will not properly boot and will reset itself. This error is generally indicative of a larger LC-wide problem. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action This error is unlikely to occur by itself nor is it likely to be the root cause of the problem. Please copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide the gathered information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700-0-INTR_INIT_ERROR

CPU Control driver, interrupt setup error, [chars]%s

Explanation The CPU Control driver failed to initialize interrupt processing. The effect is that the line card may not function or may not function appropriately. The CPU Control driver provides low level services on the SIP 700 Line Card (LC). These include, among other things, access timeout interrupt services and bus parity error interrupt services. If these services are not available then the driver process is exited, respawned and the initialization retried. The CPU Control driver is a mandatory process. If the initialization continues to fail after several retries the LC will not properly boot and will reset itself. This error is generally indicative of a larger LC-wide problem. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action This error is unlikely to occur by itself nor is it likely to be the root cause of the problem. Please copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide the gathered information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700-3-ASICPP_INIT_ERROR

CPU Control driver, ASIC Peek/Poke setup error, continuing

Explanation The CPU Control driver failed to initialize the ASIC Peek/Poke facility. The effect is that the CPU Control driver debug Peek/Poke facility is not functional. This means that CPU Control Peek/Poke commands used exclusively by Cisco support may not be available. This does not impact normal CPU Control device operations. Note that it is unlikely that this failure would occur by itself. This failure is generally indicative of a larger LC-wide problem.

Recommended Action No action is required.

Error Message %PLATFORM-CPUCTRL_SIP700-3-EDM_INIT_ERROR

CPU Control driver, External Data Manager setup error, [chars]%s

Explanation The CPU Control driver failed to initialize External Data Manager (EDM) processing. The effect is that the CPU Control driver show commands are not functional. This means that display information used by customers and Cisco support to monitor the CPU Control device may not be available. This does not impact normal CPU Control device operations. In particular, this failure would impact the ’show controllers CPUCtrl a9k-sip-700’ commands. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action No action is required. If CPU Control display output is required then the cpu_ctrl process can be restarted on the LC in question. This process restart may or may not result in successful EDM initialization depending upon the underlying problem. Note that it is unlikely that this failure would occur by itself. This failure is generally indicative of a larger LC-wide problem.

Error Message %PLATFORM-CPUCTRL_SIP700-3-FPD_ERROR

CPU Controller: FPD agent failure, [chars] (Return code [chars])

Explanation The CPU Controller FPGA FPD agent failed to initialize. If this error is encountered the CPU Controller FPGA could not be upgraded. The failure should not have an adverse effect on the card’s normal operation. %s - description of the specific failure encountered %s - error detail, if appropriate

Recommended Action This error is unlikely to occur by itself nor is it likely to be the root cause of the problem. Please copy the contents of the system log or as much of the contents of the system log as is possible from around the time that the problem occured, gather output from the ’show tech-support’ command, call your Cisco technical support representative and provide the gathered information to the representative.

Error Message %PLATFORM-CPUCTRL_SIP700-3-TRACE_INIT_ERROR

CPU Control driver, trace setup error, continuing

Explanation The CPU Control driver failed to initialize the LTrace facility. The effect is that the CPU Control driver debug trace facility is not functional. This means that trace information used by Cisco support to help isolate CPU Control device issues may not be available. This does not impact normal CPU Control device operations. Note that it is unlikely that this failure would occur by itself. This failure is generally indicative of a larger LC-wide problem.

Recommended Action No action is required.

CPUCTRL Messages

Error Message %PLATFORM-CPUCTRL-3-ASIC_NOT_FOUND

Cpuctrl could not find [chars]

Explanation While booting up, CPUCTRL could not find the required ASICs. %s - detail description of which asic can not be found

Recommended Action Investigate the corresponding ASIC driver

Error Message %PLATFORM-CPUCTRL-3-ASIC_RESET_FAILURE

Cpuctrl could not reset board ASICs. [chars] Error.

Explanation While trying to bring up ASIC links, Cpuctrl manager could not reset MSC and PLIM board ASICs port.

Recommended Action reload the board

Error Message %PLATFORM-CPUCTRL-3-CDMA_RAM_CORRECTABLE_ERROR

Cpuctrl HW detected SBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates a correctable single-bit error occurred on this internal SRAM. The error is corrected transparently. The location will be written automatically before being read again. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-CDMA_RAM_PARITY_ERROR

Cpuctrl HW detected parity in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates an uncorrectable parity error occurred on this internal SRAM. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action Ignore the message if appears only once. Otherwise reload the board

Error Message %PLATFORM-CPUCTRL-3-CDMA_RAM_UNCORRECTABLE_ERROR

Cpuctrl HW detected MBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates an uncorrectable multi-bit error occurred on this internal SRAM. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action if this happen continous, reload the board. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-DETECTED_TX_PDMA_STALL

TX PDMA Ring Stalled, port equals [dec] ([chars]), queue equals [dec] ([chars]), cur_ind equals [dec], tx_ind equals [dec].

Explanation CPUCTRL TX PDMA ring remained full over non-transient period. Packets which could not be sent were discarded. The downstream ASIC may be stalled. Asic error logged with queue details. %d - port number %s - device name %d - queue number %s - client name %d - current descriptor index %d - current refill descriptor index

Recommended Action check the asic driver described in the error message for possible stall

Error Message %PLATFORM-CPUCTRL-3-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation Cpuctrl Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation Cpuctrl Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-ERR_INIT

[chars], Reason: [chars]. Exiting.

Explanation Cpuctrl manager encountered a fatal error and is not able to recover from the error. A reason text will be supplied; please provide this text when calling Cisco support. %s - error description %s - error code description

Recommended Action Restart the process

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_ISN

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found valid PCI ISN register from a Cpuctrl Internal Access failure.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_LINK

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found a port with valid link error registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_PCI_PM

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found valid PCI PM error registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_PCI_SN

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found valid PCI SN error registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_PCIX

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found valid PCIX error registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_DETECTED_ERROR_PORT

[chars]

Explanation The cpuctrl driver HW error interrupt handler was invoked and found a port with valid isn error registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_GASPP_READ_BUS_ERROR

Bus error when attempting User requested GASPP Read, Address equals [hex]

Explanation The user may have entered an invalid address, or else there is a HW problem.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-HW_GASPP_WRITE_ERROR

Cpuctrl HW detected error on GASPP write, Address equals [hex]

Explanation The user may have entered an invalid address that is not writable.

Recommended Action check the gaspp command, verify the address and width are correct

Error Message %PLATFORM-CPUCTRL-3-IMDR_ABORT

The IMDR procedure was aborted by this process. Error [dec] Reason [chars]

Explanation The CPUCTRL process aborted the IMDR upgrade process. Check prior log messages for possible process crahses or errors.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-IMDR_ERR

A error occurred [chars] process imdr. Error [dec] Reason [chars].

Explanation A failure occurred when interacting with IMDRs. An IMDR operation in progress may be aborted or may not complete sucessfuully.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-PCI_RAM_CORRECTABLE_ERROR_MASK

Cpuctrl HW detected SBE in [chars] Mask RAM. Key: [hex]
[chars]

Explanation Indicates a correctable single-bit error occurred on this internal SRAM. This memory is considered ’persistent’ and requires special handling as described in the ’Data_corrected’ row of Table 1.2. %s - name of ram that sbe occurred %x - key of error node recorded %s - error data

Recommended Action Ignore this unless it comes with other error message

Error Message %PLATFORM-CPUCTRL-3-PCI_RAM_CORRECTABLE_ERROR_OTHER

Cpuctrl HW detected SBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates a correctable single-bit error occurred on this internal SRAM. The error is corrected transparently. The location will be written automatically before being read again. %s - name of ram that sbe occurred %x - key of error node recorded %s - error data

Recommended Action Ignore this unless it comes with other error message

Error Message %PLATFORM-CPUCTRL-3-PCI_RAM_UNCORRECTABLE_ERROR

Cpuctrl HW detected MBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates an uncorrectable multi-bit error occurred on this internal SRAM. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action Ignore the message if appears only once. Otherwise reload the board

Error Message %PLATFORM-CPUCTRL-3-PDMA_QUEUE_RX_STOP

[chars] receiving queue [dec] ([chars]) stopped to process incoming packets

Explanation Indicated device stop process the incoming packets in the receiving queue, while there is still packets in the pdma queue. %s: device name %d: queue number %s: client name

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-PDMA_RAM_CORRECTABLE_ERROR

Cpuctrl HW detected SBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates a correctable single-bit error occurred on this internal SRAM. The error is corrected transparently. The location will be written automatically before being read again. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-PDMA_RAM_PARITY_ERROR

Cpuctrl HW detected parity in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates an uncorrectable parity error occurred on this internal SRAM. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action if this happen continous, reload the board. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-PDMA_RAM_UNCORRECTABLE_ERROR

Cpuctrl HW detected MBE in [chars] RAM. Key: [hex]
[chars]

Explanation Indicates an uncorrectable multi-bit error occurred on this internal SRAM. %s - name of ram that error occurred %x - key of error node recorded %s - error data

Recommended Action if this happen continous, reload the board. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-3-PERSISTENT_CRC_LINK_FAILURE

Cpuctrl port [dec] link is out of frame with persistent CRC errors.

Explanation Cpuctrl manager could not bring up the ASIC link on the specified port. This indicates a hardware failure on the MSC or PLIM board.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-7-ERR_BAG_REG

Bag register failed for rules. Reason: [chars]

Explanation EDM Bags are used to share information between components using sysdb. This Error indicates that bag registration failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-7-ERR_DLL_INIT

Dll Initialization for [chars] failed. Reason: [chars]

Explanation Cpuctrl driver tried to register for a dll but it encountered an error. The driver might lose some of its functionality.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation Cpuctrl Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRL-7-ERR_SYSDB_EDM_REG

Sysdb Register EDM failed. Reason: [chars]

Explanation Cpuctrl Sysdb Register EDM error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CPUCTRLLIB Messages

Error Message %PLATFORM-CPUCTRLLIB-3-DETECTED_CDMA_PORT0

CDMA to port 0 channel equals [dec], queue equals [dec] ([chars]). ASIC address [[hex],[hex]]

Explanation The cpuctrl driver detected an attempt to DMA to port 0. The request was discarded and not performed. %d - channel number %d - queue number %s - client name %x - address high 32bit %x - address low 32bit

Recommended Action Investigate the client that attempting the DMA access No action is required.

Error Message %PLATFORM-CPUCTRLLIB-3-DETECTED_EGRESSQ_QUEUE0_PDMA

TX PDMA to EgressQ queue 0, port equals [dec], queue equals [dec] ([chars]). Buffer Header: [hex]. Initial packet data(hex): [chars]

Explanation The cpuctrl driver detected an attempt to DMA a packet to egressq queue 0. The packet was discarded and not sent.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-3-DETECTED_ERROR_PDMA

[chars], [dec], port equals [dec] ([chars]), queue equals [dec] ([chars])

Explanation The cpuctrl driver detected an error during packet DMA.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-3-DETECTED_RX_DROP_ERROR

device [dec] PDMA rx queue [dec]([chars]) drop error

Explanation The indicated rx pdma queue has a drop error occurred %d - device id %d - queue number %s - client name

Recommended Action No action is required.

Error Message %PLATFORM-CPUCTRLLIB-3-DETECTED_TRUNCATED_TX_PKT

[chars], Pak Particle count equals [dec], datagram_size equals [dec], port equals [dec],queue equals [dec]([chars])

Explanation This error indicates that a packet sent to the squidlib code by the client was truncated while the squidlib code was trying to send the packet. The squidlib has aborted the tx operation as the packet doesn’t have any particles to send

Recommended Action No action is required.

Error Message %PLATFORM-CPUCTRLLIB-3-HW_DETECTED_ERROR_CDMA

HW set the error bit in a CDMA descriptor
CDMA engine equals [dec], queue equals [dec] ([chars]), index equals [dec]
error reg_lo equals [hex], error_reg_hi equals [hex]

Explanation CDMA ended in error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-3-HW_DETECTED_ERROR_RX_PDMA

HW set the error bit in a RX PDMA descriptor
port equals [dec] ([chars]), queue equals [dec] ([chars]), index equals [dec]

Explanation The cpuctrl driver detected a buffer marked with an error, possibly a CRC check. The buffer is discarded.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-3-UNRECOVERED_PIO_ERROR

Restarting cpuctrl client [dec] ([chars]) on port [dec] for devid [dec] ([chars]) on unrecovered PIO error notification

Explanation A PIO error was detected and the responsible client was notified but did not mark the error as recovered. Restarting the client.

Recommended Action No action is required.

Error Message %PLATFORM-CPUCTRLLIB-4-INT_WARNING

Excess Spurious interrupt on device [chars]

Explanation The cpuctrllib ASIC Interrupt wrapper has detected that an ASIC driver has not cleared its interrupts at the source for 1000 consecutive times. This is possibly an error in the Driver ISR, that does not process and clear all possible interrupts, or malfunctioning HW. The Interrupt is disabled to prevent the ISR from hogging the CPU.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-4-PORT_INIT_FAILURE

Port [dec] ([chars]) could not clear Link errors during init
link_error_reg equals [hex], crc_reg equals [hex]

Explanation Port will not operate reliably

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-4-PORT_NOT_PRESENT

Attempt to access Port [dec] which was not discovered
Device ID_reg equals [hex], devid equals [hex]

Explanation Port will not operate reliably

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-4-PORT_REFRAME_SYNC_FAILURE

Port [dec] ([chars]) would not sync on reframe attempt

Explanation Port will not operate reliably

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-4-PORT_REINIT_FAILURE

Port [dec] ([chars]) Device chipid mismatch during reframe
id_reg read after reframe equals [hex], id_reg during HW discovery equals [hex]

Explanation Port will not operate reliably

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CPUCTRLLIB-6-NO_BUF_TO_REPLACE

RX PDMA Ring out of buf, Port [dec] ([chars]), Q [dec] ([chars]), cur_ind equals [dec], tx_ind equals [dec], retry [dec]

Explanation CPUCTRL RX PDMA ring could not replace the buffers, possible low buffer condition.

Recommended Action If the message is displayed continuously for just a short period of time, it is likely a temporary condition that RX PDMA Ring is out of buffer. Use command ’show packet-memory inuse summary’ to check which process holding most of the packets and restart the process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CROSSBAR Messages

Error Message %PLATFORM-CROSSBAR-1-HI_FPOE_DB_CORR_ECC_ERROR_LNK0

Crossbar unicast FPOE DB correctable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast FPOE correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_FPOE_DB_CORR_ECC_ERROR_LNK1

Crossbar unicast FPOE DB correctable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast FPOE correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_FPOE_DB_UCORR_ECC_ERROR_LNK0

Crossbar unicast FPOE DB uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast FPOE uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_FPOE_DB_UCORR_ECC_ERROR_LNK1

Crossbar unicast FPOE DB uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast FPOE uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_IN_MEM_CORR_ECC_ERROR_LNK0

Crossbar unicast input memory detected correctable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast input memory correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_IN_MEM_CORR_ECC_ERROR_LNK1

Crossbar unicast input memory detected correctable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast input memory correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_IN_MEM_UCORR_ECC_ERROR_LNK0

Crossbar unicast input memory detected uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast input memory uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_IN_MEM_UCORR_ECC_ERROR_LNK1

Crossbar unicast input memory detected uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast input memory uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_OUT_MEM_CORR_ECC_ERROR_LNK0

Crossbar unicast output memory detected correctable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast output memory correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_OUT_MEM_CORR_ECC_ERROR_LNK1

Crossbar unicast output memory detected correctable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast output memory correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_OUT_MEM_UCORR_ECC_ERROR_LNK0

Crossbar unicast output memory detected uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected unicast output memory uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-HI_OUT_MEM_UCORR_ECC_ERROR_LNK1

Crossbar unicast output memory detected uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected unicast output memory uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-IN_BUF_CRC_ERROR_LNK0

Excessive Crossbar input buffer CRC error on [chars] link 0

Explanation Crossbar driver detected excessive input buffer CRC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-IN_BUF_CRC_ERROR_LNK1

Excessive Crossbar input buffer CRC error on [chars] link 1

Explanation Crossbar driver detected excessive input buffer CRC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-IN_MEM_ERROR_LNK0

Crossbar driver input memory error on [chars] link 0

Explanation Crossbar driver detected a input memory error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-IN_MEM_ERROR_LNK1

Crossbar driver input memory error on [chars] link 1

Explanation Crossbar driver detected a input memory error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_FPOE_DB_CORR_ECC_ERROR_LNK0

Crossbar multicast FPOE DB correctable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast FPOE correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_FPOE_DB_CORR_ECC_ERROR_LNK1

Crossbar multicast FPOE DB correctable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast FPOE correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_FPOE_DB_UCORR_ECC_ERROR_LNK0

Crossbar multicast FPOE DB uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast FPOE uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_FPOE_DB_UCORR_ECC_ERROR_LNK1

Crossbar multicast FPOE DB uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast FPOE uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_IN_MEM_CORR_ECC_ERROR_LNK0

Crossbar multicast input memory detected correctable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast input memory correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_IN_MEM_CORR_ECC_ERROR_LNK1

Crossbar multicast input memory detected correctable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast input memory correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_IN_MEM_UCORR_ECC_ERROR_LNK0

Crossbar multicast input memory detected uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast input memory uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_IN_MEM_UCORR_ECC_ERROR_LNK1

Crossbar multicast input memory detected uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast input memory uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_OUT_MEM_CORR_ECC_ERROR_LNK0

Crossbar multicast output memory detected correctable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast output memory correctable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_OUT_MEM_CORR_ECC_ERROR_LNK1

Crossbar multicast output memory detected correctable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast output memory correctable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_OUT_MEM_UCORR_ECC_ERROR_LNK0

Crossbar multicast output memory detected uncorrectable ECC error on [chars] link 0

Explanation Crossbar driver detected multicast output memory uncorrectable ECC error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-LOW_OUT_MEM_UCORR_ECC_ERROR_LNK1

Crossbar multicast output memory detected uncorrectable ECC error on [chars] link 1

Explanation Crossbar driver detected multicast output memory uncorrectable ECC error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-OUT_MEM_ERROR_LNK0

Crossbar driver output memory error on [chars] link 0

Explanation Crossbar driver detected an output memory error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-OUT_MEM_ERROR_LNK1

Crossbar driver output memory error on [chars] link 1

Explanation Crossbar driver detected an output memory error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-SERDES_ERROR_LNK0

Crossbar driver serdes error on [chars] link 0

Explanation Crossbar driver detected a serdes error on link 0.

Recommended Action This error is a momentary error. If this error persists for a period of 60 seconds after all the cards are in IOS-XR RUN state using the ’show platform’ command, please attempt to correct the error by reloading the card by issuing the command: ’hw-module loc reload’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-SERDES_ERROR_LNK1

Crossbar driver serdes error on [chars] link 1

Explanation Crossbar driver detected a serdes error on link 1.

Recommended Action This error is a momentary error. If this error persists for a period of 60 seconds after all the cards are in IOS-XR RUN state using the ’show platform’ command, please attempt to correct the error by reloading the card by issuing the command: ’hw-module loc reload’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-XBAR_TIMEOUT_ERROR_LNK0

Crossbar driver detected crossbar timeout error on [chars] link 0

Explanation Crossbar driver detected an crossbar timeout error on link 0

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-1-XBAR_TIMEOUT_ERROR_LNK1

Crossbar driver detected crossbar timeout error on [chars] link 1

Explanation Crossbar driver detected an crossbar timeout error on link 1

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-2-ACCESS_FAILURE

Crossbar ASIC access failed [chars]

Explanation Crossbar driver detected an issue with ASIC access.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-2-BIST_FAILURE

Crossbar ASIC BIST failed [chars]

Explanation Crossbar driver detected ASIC BIST failure.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-2-TEMP_OVER_LIMIT

Crossbar ASIC current temperature [chars] is over threshold

Explanation Crossbar driver detected that the current ASIC temperature is over threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-4-MULTICAST_THRESHOLD_CROSSED_LNK0

Crossbar multicast queue utilization crossed threshold, [chars]

Explanation Crossbar driver detected multicast queue utilization is over configured threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-CROSSBAR-4-MULTICAST_THRESHOLD_CROSSED_LNK1

Crossbar multicast queue utilization crossed threshold, [chars]

Explanation Crossbar driver detected multicast queue utilization is over configured threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

DC_SERVICE_SRVR Messages

Error Message %PLATFORM-DC_SERVICE_SRVR-2-ERR_EVM_EVENT_BLOCK

[chars]

Explanation An error occurred in the event loop. It may be possible to rectify it by restarting the process.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DC_SERVICE_SRVR-2-RECV_ERROR

Failed to get response from cores: [chars]

Explanation Some or all the cores didn’t respond for a configuration.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DC_SERVICE_SRVR-3-DEBUG_ERROR

[chars]: [chars]

Explanation Encountered an error in debug module. This error should not impact the major functionality of the module.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DC_SERVICE_SRVR-3-DLL_ERROR

Failed to [chars] [chars] DLL: [chars]

Explanation An error occurred while trying to open or initialize a DLL. The process will be restarted.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DC_SERVICE_SRVR-3-INIT_CRITICAL_ERROR

[chars]: [chars]: [hex]

Explanation A critical error occured during the initialization of DC_SERVICE_SRVR process which involves exiting the process. The DC_SERVICE_SRVR will restart and unless the same error occurs on the next attempt the DC_SERVICE_SRVR will function normally. If the error is persistent, it indicates the system error or HW error which needs further investigation. The cause of the error will be mentioned in the message displayed.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DC_SERVICE_SRVR-3-LTRACE_ERROR

Error encountered tracing for [chars]: [chars]

Explanation Encountered an error in tracing module. This error should not impact the major functionality of the module.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

DIAGS Messages

Error Message %PLATFORM-DIAGS-0-LC_NP_LOOPBACK_FAILED

NP loopback failure count crossed threshold, [chars]

Explanation This line card has detected a problem with the packet punt and injection path between this line card CPU and some network processor(s), and the consecutive failure count has reached or crossed the failure threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-0-LC_NP_LOOPBACK_FAILED_RX_PATH

NP loopback failure count crossed threshold, [chars]

Explanation This line card has detected a problem with the packet punt and injection path between this line card CPU and some network processor(s), and the consecutive failure count has reached or crossed the failure threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-0-LC_NP_LOOPBACK_FAILED_TX_PATH

NP loopback failure count crossed threshold, [chars]

Explanation This line card has detected a problem with the packet punt and injection path between this line card CPU and some network processor(s), and the consecutive failure count has reached or crossed the failure threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-EXCESSIVE_ECC_SBE_ERROR

Excessive ECC Single-bit errors

Explanation The number of single-bit ECC errors has crossed the error threshold.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-FAB_MCAST_SC0_FAILED

Fabric multicast loopback (SC0) failure count crossed threshold.

Explanation A problem is detected by loopback test to the first Crossbar chip (chip#0) on this RSP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-FAB_MCAST_SC1_FAILED

Fabric multicast loopback (SC1) failure count crossed threshold.

Explanation A problem is detected by loopback test to the second Crossbar chip (chip#1) on this RSP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-FAB_UNICAST_FAILED

Fabric unicast loopback failure count crossed threshold.

Explanation A problem is detected by loopback test to the Crossbar chips on this RSP.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-FPD_IMG_CORRUPTED

FPD image integrity check failed,

Explanation An FPD image in non-volatile memory is corrupted or missing. Each FPD has 2 images stored in non-volatile memory, one is field upgradable version; the ’B’ version. The other is the backup version; the ’A’ version. If a B version FPD image has gone bad, it can be recovered by following the recommended_action. If the A version has gone bad, the board must be replaced.

Recommended Action Use the following command to find out which FPD image is bad/missing: ’show log | inc PFM | inc FPD’; If it is the B version (the upgradable version), then reprogram the image using the upgrade command: ’admin’ ’upgrade hw fpd fpga-selection force location node-failed’ If any A version is bad, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-INVALID_DEVICE_ID

Device identity readback value is incorrect

Explanation Device identity readback value is incorrect

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_FAILED_BOTH_RSP

LC lost EOBC heartbeat to both RSPs.

Explanation This line card has lost EOBC heartbeat to both RSPs

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_FAILED_RSP0

EOBC Heartbeat failure count for RSP0 ([chars]) crossed threshold.

Explanation This line card has lost EOBC heartbeat to RSP0.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_FAILED_RSP1

EOBC Heartbeat failure count for RSP1 ([chars]) crossed threshold.

Explanation This line card has lost EOBC heartbeat to RSP1.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_FAILED_STBY_RSP

LC lost EOBC heartbeat to the Standby RSP.

Explanation This line card has lost EOBC heartbeat to the standby RSP.

Recommended Action If this happens during system booting and switchover or when the standby RSP is not in ’IOS XR RUN’ state, this message can be safely ignored. Otherwise, If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_NO_RSP_UP

No RSP is up, LC EOBC heartbeat skipped. [chars]

Explanation This line card found there is no RSP present in the system.

Recommended Action This condition should not last long, the line card should reset. No action is required.

Error Message %PLATFORM-DIAGS-3-LC_EOBC_SEND_FAILED

Failed to send a heartbeat to RSP [chars]

Explanation This line card has failed to transmit a heartbeat to a RSP over EOBC.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-PUNT_FABRIC_DATA_PATH_FAILED

System punt, fabric and data path failure count crossed threshold, [chars]

Explanation A problem is detected on the system punt, fabric or data path between this RSP CPU to one or more of the network processor(s) on some line card(s).

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-SCRATCH_TEST_ERROR

Device scratch register test has failed

Explanation The CPU at the failed location has failed to access the named device scratch register.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-SRSP_ACTIVE_EOBC_FAILED

Heartbeat failed over active EOBC, [chars]

Explanation Standby RSP has detected an error with the active eobc link between this standby RSP and one or more line card)(s)

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-SRSP_ACTIVE_EOBC_MCAST_FAILED

Failed to broadcast heartbeat over active EOBC.

Explanation Standby RSP failed to transmit heartbeat to all nodes via active EOBC links.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-SRSP_STANDBY_EOBC_FAILED

Heartbeat failed over Standby EOBC, [chars]

Explanation Standby RSP has detected an error with the standby eobc link between this standby RSP and one or more line card)(s)

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %PLATFORM-DIAGS-3-SRSP_STANDBY_EOBC_MCAST_FAILED

Failed to broadcast heartbeat over standby EOBC.

Explanation Standby RSP failed to transmit heartbeat to all nodes via standby EOBC links.

Recommended Action