Cisco IOS XR System Error Message Reference Guide, Release 4.3.x
Fabric Messages
Downloads: This chapterpdf (PDF - 2.41 MB) The complete bookPDF (PDF - 18.29 MB) | Feedback

Table of Contents

Fabric Messages

CCSQ_DLL Messages

CCSQ_LIB Messages

CCSQ_MGR Messages

FAB_SVR Messages

FABQ Messages

FABRIC_140G_POD Messages

FABRIC_COMM_DRVR Messages

FABRIC_DRIVER_LITE Messages

FABRIC_DRVR_SHARED Messages

FABRIC_DRVR Messages

FABRIC_SRVR Messages

FABRICQ_MGR Messages

FABRICQ Messages

FDI Messages

FEATURE_LPTS Messages

FGID_AGG Messages

FGID_ALLOC Messages

FGID_BCDL_CONSUMER Messages

FGID_LIB Messages

FGID_SVR Messages

FIA_API Messages

FIA Messages

FIFO Messages

FSDB_FADB_MAIN Messages

FSDB_FADB Messages

FSDB Messages

FSTATSA Messages

FSTATSC Messages

FSTATSS Messages

HFR_FSDB_FADB_LTRACE Messages

INGRESSQ_ALARM Messages

INGRESSQ_DLL Messages

INGRESSQ_LIB Messages

INGRESSQ Messages

Fabric Messages

This section contains all Fabric (hardware and software both) related System Error Messages.

CCSQ_DLL Messages

Error Message %FABRIC-CCSQ_DLL-2-DEVICE_HALT

CCSQ: device halted, sub-block: [chars], halted entity: [chars]

Explanation CCSQ, ASIC got halted. The halted block and its parent block are provided

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-2-ERR_EIO_TRAIN

EIO link training threshold exceeded, link: [dec]

Explanation Repeated attempts to train the EIO links to the neighboring Asic have failed. No further attempts to retrain the link will be made.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-2-TAKING_NODE_DOWN

Taking the node down, Reason: [chars]

Explanation CCSQ DLL encountered an fatal error mentioned above. The driver triggers MSC node-down to recover from the error.

Recommended Action This might be a recovery action from a fault. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-3-ERR_ASIC_GENERIC

Block: [chars], Generic Error [chars] at Memory Address [hex].

Explanation CCSQ encountered a device error that has exceeded its threshold value. Driver takes appropriate action to log and fix the error which may include a device reset.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-3-ERR_ASIC_MBE

Multiple Bit Error in Block: [chars] Error: [chars].

Explanation CCSQ encountered a multiple bit error in the mentioned block. This error is an uncorrectable error. Driver takes appropriate action to log and fix the error which may include a device reset.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-3-ERR_INIT

[chars]

Explanation The CCSQ driver failed to initialize the device resulting in the restart of the CCSQ driver process.

Recommended Action Collect all the event logs and the output of the following command executed from the CLI of the active RP: ’show process ccsq_mgr’ Also, collect the fabric snapshot: ’show fabric-snapshot file loc ’

Error Message %FABRIC-CCSQ_DLL-3-ERR_MEM_ALLOC

Error Allocating memory for [chars]

Explanation The CCSQ dll Memory Allocation Error message.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-3-RESET

Resetting CCSQ ASIC Device

Explanation CCSQ, cpuctrl net interface encountered a CRC/Sync Error. This will result in the PIO or CDMA failure.

Recommended Action If it is possible to isolate the trigger point for the sn link error, collect all the necessary condition that caused the error. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-4-ERR_ASIC_CRC

CRC Error: Block:[chars] Error:[chars] Count: [dec]

Explanation CCSQ block received a packet with a CRC error. It is primarily caused by either the link errors between the devices or packet corruption in the upstream asic. This error may cause performance degradation.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-4-ERR_ASIC_SN_LINK

CpuCtrl Interface RxFIFO Error: [chars]

Explanation CCSQ, cpuctrl net interface Rx FIFO last sync.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-4-INTR_ENABLE_FAIL

Interrupt enable at addr: [hex] mask: [hex] failed.

Explanation Hardware state is not correct.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-5-ERR_ASIC_PARITY

Block: [chars], entity: [chars] had parity error(s), addr: [dec], parity: [dec]

Explanation In the specified block a parity error encountered at mentioned addr offset. If the error exceeds its threshold, the driver trigger a corrective action which may include device reset or MSC reload.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-5-ERR_ASIC_SBE

Single Bit Error in Block: [chars] Error: [chars].

Explanation CCSQ encountered a single bit error in the mentioned block. Persistent errors are corrected by the software. Non-persistent errors are automatically corrected by the next write operation.

Recommended Action This error is an correctable error. There are no side effects. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_DLL-7-ERR_REGISTER_GET

Register get failed for address [hex], Reason: [chars]

Explanation An attempt to read a Hardware register failed. This could result in inconsistent behavior of the device.

Recommended Action Run diags on the board and contact TAC support. If it is possible to isolate the trigger point for the read failure, collect all the necessary condition that caused the error. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CCSQ_LIB Messages

Error Message %FABRIC-CCSQ_LIB-7-ERR_LWM_SEND

CCSQ Lib: LWM Message send failed msg: [dec], retried: [dec] time(s), errno: [chars]

Explanation Unable to send a LWM message to the CCSQ server.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

CCSQ_MGR Messages

Error Message %FABRIC-CCSQ_MGR-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation CCSQ manager encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation CCSQ encountered a fatal memory allocation error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_BAG_REG

Bag register failed for rules. Reason: [chars]

Explanation EDM Bags are used to share information between components using sysdb. This Error indicates that bag registration failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_CLIENT_REG

Client [chars] failed. Reason: [chars]

Explanation CCSQ Manager client Registration/Unregistration error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_DLL_INIT

Dll Initialization for [chars] failed. Reason: [chars]

Explanation CCSQ driver tried to register for a dll but it encountered an error. The driver might lose some of its functionality.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation CCSQ Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation CCSQ Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation CCSQ Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation CCSQ LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-CCSQ_MGR-7-ERR_SYSDB_EDM_REG

Sysdb Register EDM failed. Reason: [chars]

Explanation CCSQ Sysdb Register EDM error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FAB_SVR Messages

Error Message %FABRIC-FAB_SVR-7-ERR_ASIC_INIT

Failed to initialize the the CPU control ASIC interface to [chars]: [chars]. Exiting...

Explanation Fabric server encountered an error while initializing the CPU control ASIC to either receive packets from the fabricq ASIC or transmit packets from the ingressq ASIC. This is crucial for the process and is automatically restarted on this failure.

Recommended Action If problem either persists (following a process restart) then Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FAB_SVR-7-ERR_EVENT_CONN_EVM_HANDLER

Failed to register event handler, Reason: [chars]([dec]). Exiting...

Explanation Fabric server encountered an error while trying to register event handler for the posix message queue. This facility is deemed crucial and the process automatically restarts on this failure.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_EVENT_CONN_NOTIFY

Failed to register handler for disconnection with EVM, Reason: [chars]([dec]). Exiting...

Explanation Fabric server encountered an error while trying to register event handler for disconnection or connection error event. This facility is deemed crucial and the process automatically restarts on this failure.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_EVENT_CONN_OPEN

Failed to open connection with EVM, Reason: [chars]([dec]). Exiting...

Explanation Fabric server encountered an error while trying to open connection with event manager. This facility is deemed crucial and the process automatically restarts on this failure.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_EVM_CREATE

Failed to create the event manager. Reason: [chars]. Exiting...

Explanation Fabric server encountered an error while attempting to create an event manager. This failures affects the ability of the process to service various messages / pulses from other threads / processes. This facility is deemed crucial and the process automatically restarts on this failure. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_FSM_STATE

[chars](id [unsigned int], event [unsigned int]). Invalid req_state [unsigned int]! Exiting...

Explanation Fabric server encountered an unexpected/invalid state while trying to process an event for a client request. This facility is deemed crucial and the process automatically restarts on this failure.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_HEARTBEAT_FAILURE

Heartbeat connection broken to node [unsigned int]

Explanation Fabric server heartbeat monitoring mechanism detected interruption in the periodic ’Hello’ messages.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_HEARTBEAT_FSM_STATE

Heartbeat State Machine was found to be in invalid state [unsigned int] while processing event [unsigned int].

Explanation Fabric server heartbeat monitoring mechanism detected a problem in the internal state machine.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_INIT

[chars] during the initialization. Reason: [chars]. Exiting...

Explanation Fabric server encountered the specified error during the initialization sequence. This facility is deemed crucial and hence the process is automatically restarted on this failure. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_RRW_LOCK

[chars]() rrw lock: 0x[pointer]

Explanation Fabric server failed to aquire rrw lock to the request record area in shared memory.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_RRW_UNLOCK

[chars]() rrw lock: 0x[pointer]

Explanation Fabric server failed to release rrw lock to the request record area in shared memory. This is a fatal error, the process will automatically restart.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

Error Message %FABRIC-FAB_SVR-7-ERR_THREAD_ATTRIBUTE

Failed to set the thread attribute: [chars]. Exiting...

Explanation Fabric server encountered an error while setting the thread attribute during the process initialization sequence. This is crucial for the process and is automatically restarted on this failure.

Recommended Action If the problem is experienced only by this process in the system, restart the fabric server process by executing the following command at the CLI of the active RP: process restart fab_svr location loc If problem either persists (following a process restart) or also noticed on other processes then Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FAB_SVR-7-ERR_THREAD_MUTEX_INIT

Failed to initialize a mutex for client with ID [dec]: [chars]. Exiting...

Explanation Fabric server encountered an error while creating a mutex for use by a client with the specified ID. This is crucial for the process and is automatically restarted on this failure.

Recommended Action If the problem is experienced only by this process in the system, restart the fabric server process by executing the following command at the CLI of the active RP: process restart fab_svr location loc If problem either persists (following a process restart) or also noticed on other processes then Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FAB_SVR-7-INFO_SHM

Shared memory region [chars] [chars] changed: old [unsigned int], new [unsigned int]. Reinitializing...

Explanation Fabric server encountered a change in the shared memory region parameter.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..

FABQ Messages

Error Message %FABRIC-FABQ-0-PRP3_FAULT_RECOVERY_ERR

ToFab component of the fabric driver has failed. The root fault was: [chars]

Explanation When a hardware fault occurs and the device driver cannot correct it, the Platform Manager is required to reset the ASICs. This error indicates that the Platform Manager failed to reset the ASICs and the hardware on the PRP may not be in an operational state. This condition affects the functionality of the entire router. %s is the Interrupt Source.

Recommended Action If the system has not failed over automatically and a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0 ’ where x is the slot of route processor that generated the error. If no redundant RP is configured you will need to reboot the router by issuing the reload command. Call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-2-PRP3_DRVR_INIT_ERROR

Process initialization failed: [chars] Reason: [chars]

Explanation PRP fabric queue process failed to initialize. The fabric driver process handles fabric connectivity. It initializes the packet FPGA and coordinates with that fabric DLLs that allow applications to send and recieve packets via the fabric. An unrecoverable failure of the process may prevent this route processor from communicating with other cards in the chassis. %s - indicates the reason for the failure. %s - is the error reason.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-2-PRP3_PKT_INIT_ERROR

Packet carving failed to initialize: [chars] Reason: [chars]

Explanation Initial carving of a packet particle pool failed. Platform specific memory region, packet header and particle pool configuration information are required by the generic packet manager process (PAKMAN) to operate. A failure in packet carving initialization may prevent this route processor from communicating with other cards in the chassis. %s - indicates the reason for the failure. %s - is the error reason.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-FATAL

FABQ: fatal error encountered, reason equals [chars]

Explanation Fabric Queue Driver encountered a fatal error and is not able recover from the error. A reason text will be supplied. Call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-INIT_ERROR

Process initialization failed: ([chars]%s)

Explanation PRP fabric queue process failed to initialize. The fabric queue process handles fabric connectivity. It initializes and starts up the threads in ToFab and FrFab components. An unrecoverable failure of the process may prevent this route processor from communicating with other cards in the chassis. %s - indicates the reason for the failure. %s - is the error reason.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PKT_INIT_ERROR

Packet carving failed to initialize: ([chars]%s)

Explanation Initial carving of a packet particle pool failed. Platform specific memory region, packet header and particle pool configuration information are required by the generic packet manager process (PAKMAN) to operate. A failure in packet carving initialization may prevent this route processor from communicating with other cards in the chassis. %s - indicates the reason for the failure. %s - is the error reason.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PKT_INIT_FAIL

PKT_INIT: [chars] failed, rc equals [dec], reason:[chars]

Explanation Packet carving function has failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PKT_INIT_POOL

PKT_INIT: particle_multi_pool_define failed ([chars]), rc equals [dec], reason:[chars]

Explanation Initial carving of a packet particle pool has failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_FABMSG

Fabric messaging infrastructure failed: [chars] Reason: [chars]

Explanation PRP fabric messaging infrastructure failed. The fabric driver process handles fabric connectivity. It initializes the packet FPGA and coordinates with that fabric DLLs that allow applications to send and recieve packets via the fabric. An unrecoverable failure of the process may prevent this route processor from communicating with other cards in the chassis. %s - indicates the reason for the failure. %s - is the error reason.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_FRFAB_PKT_NO_STREAM

Client ID([dec]) Port([dec]) From Fabric Packet from slot [dec] has invalid Stream ID([dec])

Explanation The packet received from the fabric begins with a header with Stream ID not initialized. The issue can happen due to hardware issue or the sender of the packet encoded invalid information in the packet header. %d - Client ID. Every process that uses the fabric API has an unique Client ID. %d - Port number (0 to 15) %d - Sender’s slot number (0 to 15) %d - Stream ID encoded in the packet’s header

Recommended Action If the error recurs very frequently call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_FRFAB_PKT_STARTOFFSET

Client ID([dec]) Port([dec]) From Fabric Packet from slot [dec] has invalid Start Offset([dec])

Explanation The packet received from the fabric begins with a header with Start Offset less than the required. This suggests the packet is corrupted. The issue can happen due to hardware issue or the sender of the packet encoded invalid information in the packet header. %d - Client ID. Every process that uses the fabric API has an unique Client ID. %d - Port number (0 to 15) %d - Sender’s slot number (0 to 15) %d - Start Offset encoded in the packet’s header

Recommended Action If the error recurs very frequently call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_FRFAB_TAIL_PAR_ERR

Client ID([dec]) Port([dec]) Fabric FPGA detects Parity error from a packet received from the Fabric

Explanation The Hummer detects a parity error on a packet received from the fabric. This is likely due to a hardware issue, or software misconfigured the hardware. %d - Client ID. Every process that uses the fabric API has an unique Client ID. %d - Port number (0 to 15)

Recommended Action The prp3_fabric_driver process should be able to detect the error and decide to reset fabric FPGA if necessary. If the error is persistent, and router traffic is affected, and if the system has not failed over automatically and a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode ’reload location RP/0/x/CPU0 ’ where x is the slot of route processor that generated the error. If no redundant RP is configured you will need to reboot the router by issuing the reload command. Call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_HW_IRQ_ERR

Hummer Port([dec]) Interrupt- type([dec]) - [chars]: Reason: [chars]

Explanation An error is detected when the software is trying to service an interrupt from the Hummer FPGA. Hummer is the fabric packet processing FPGA on the route processor. There are 16 bidirectional ports for 16 different traffic streams. A Hummer port needs to be enabled in the hardware level in order to function. A failure in servicing the Hummer interrupt may prevent this route processor from communicating with other cards in the chassis. %d - indicates the port number (0 to 15) %d - interrupt number that identifies the interrupt type %s - a decription of the interrupt event failure %s - is the error reason

Recommended Action Try restarting the process where the error message was found. Otherwise, try the following: If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_IRQ_ERR

Fabric FPGA Error Interrupt: [chars]

Explanation An error is detected when the software is trying to service an interrupt from the Hummer fabric FPGA. Hummer is the fabric packet processing FPGA on the route processor. There are 16 bidirectional ports for 16 different traffic streams. A Hummer port needs to be enabled in the hardware level in order to function. An error status interrupt may indicate a hardware condition that may prevent this route processor from communicating with other cards in the chassis.

Recommended Action If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_PORT_DISABLE_ERR

Cannot disable Hummer port([dec]): Reason: [chars]

Explanation Failed to disable Hummer port. Hummer is the fabric packet processing FPGA on the route processor. There are 16 bidirectional ports for 16 different traffic streams. A Hummer port needs to be enabled in the hardware level in order to function. A failure in disabling the Hummer port may prevent this route processor from communicating with other cards in the chassis. It points to a HW issue or a serious software defects. %d - indicates the port number (0 to 15) %s - is the error reason.

Recommended Action Try restarting the process where the error message was found. Otherwise, try the following: If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_PORT_ENABLE_ERR

Cannot enable Hummer port([dec]): Reason: [chars]

Explanation Failed to enable Hummer port. Hummer is the fabric packet processing FPGA on the route processor. There are 16 bidirectional ports for 16 different traffic streams. A Hummer port needs to be enabled in the hardware level in order to function. A failure in enabling the Hummer port may prevent this route processor from communicating with other cards in the chassis. %d - indicates the port number (0 to 15) %s - is the error reason.

Recommended Action Try restarting the process where the error message was found. Otherwise, try the following: If a redundant route processor card has been configured: 1 - force a failover with the following command in admin mode: ’redundancy switchover’ 2 - reload the route processor card that failed with the following command in admin mode: ’reload location RP/0/x/CPU0’ where x is the slot of route processor that generated the error. If no redundant RP is configured, you will need to reboot the router by issuing the reload command. If the error recurs call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_REUSE_NO_BUFFER

Client ID([dec]) Port([dec]) Packet passed to client cannot be reused since there is No Buffer

Explanation The packet processing code formats packets from the fabric and passes them to the clients. When the client finished with the packet, the packet processing code cannot reuse the packet buffer because none is found associated with the packet. The issue can happen due to a software issue with the client. %d - Client ID. Every process that uses the fabric API has an unique Client ID. %d - Port number (0 to 15)

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_SHM

Shared Memory failed during [chars]: [chars]

Explanation An internal software error occurred that prevented the fabric interface from working properly with shared memory.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_TOFAB_CREDIT_CNT_EXCEEDED

RP To Fabric Credit Count([dec]) for destination slot [dec] is greater than the limit. Port([dec])

Explanation PRP3 fabric hardware requires software to track To Fabric hardware resources for each chassis slot. During the update of this shared per slot information, software detected the resources for this slot exceeded that actual maximum available. This is likely the side affect of a packet resource management event in the fabric driver DLL. %d To Fabric count that exceeds maximum %d The slot associated with the error %d The fabric application port that detected the error (but not necessarily the port that caused the error.

Recommended Action The error is likely a software bug in tofab packet error or process restart handling. Copy the error message exactly as it appears and report it to your Cisco technical representative together with the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_TOFAB_QUEUE_BLOCKED

RP To Fabric Queue slot:[dec] is Blocked, report fault to Sysldr

Explanation The PRP3 to fabric queue of the particular priority and slot is blocked. This means packets that go that slot of that priority will fail. In addition, at least one of the multicast queues (high or low priority) is blocked as well. This likely means the particular slot is failing to accept packets and will cause backpressure on the PRP to fabric queue. Because of hardware design, if a multicast packet includes the one faulty slot then it will be stuck in the tofab multicast queue, and subsequent multicast packets will be stuck even if they do not include the faulty slot in their slotmask. Having the unicast queue blocked is somewhat allowable, but having the multicast queue blocked is not acceptable. This error message is raised when both unicast and multicast are blocked. In order to alleviate this problem, the fault is sent to sysldr, for sylsdr to decide to reload the slot. It is very likely that the problem slot was not accepting packets. slot:%d - is the slot that is back pressuring to the PRP

Recommended Action The slot should be reloaded to correct the problem, if not done already by sysldr. Copy the error message exactly as it appears and report it to your Cisco technical representative together with the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-PRP3_TX_DONE_RING

RP To Fabric Tx Done Ring. Port:[dec], Tx Index: [dec]: [chars]

Explanation While servicing To Fabric packets which the PRP3 Fabric FPGA indicates have been transmitted, software detects differences between hardware packet list and software cache of what was to be transmitted. Port:%d the PRP3 hardware fabric port that reported the issue Index:%d the index of the Tx Done Ring when error reported %s a decription of the To Fabric event failure

Recommended Action Copy the error message exactly as it appears and report it to your Cisco technical representative together with the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-3-SHOW_ERR

FABQ_SHOW: fatal error encountered: [chars]

Explanation Error while executing a show command

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABQ-6-PKT_INIT_INFO

PKT_INIT: pak mem size:[hex], pak mem start: [hex], pak scaling:[dec]

Explanation Information on packet memory carving

Recommended Action This is information and does not require any correction.

Error Message %FABRIC-FABQ-7-PKT_INIT_INFO

Packet initialization: pak mem size:[hex], pak mem start: [hex], pak scaling:[dec]

Explanation Information on packet memory carving.

Recommended Action This is informational and does not require any correction.

Error Message %FABRIC-FABQ-7-PRP3_PKT_INIT_INFO

Packet initialization: pak mem size:[hex], pak mem start: [hex], pak scaling:[dec]

Explanation Information on packet memory carving.

Recommended Action This is debug-level informational and does not require any correction.

FABRIC_140G_POD Messages

Error Message %FABRIC-FABRIC_140G_POD-2-TX_CH_FAULT

Tx POD detects a fault on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec]

Explanation The Tx POD detects a fault on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption in the downstream.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-ASIC_ERR_INIT

Cannot initialize asic error lib [chars]. rc([hex]) [chars]

Explanation The sfe-drvr process cannot initialize the infrastructure allow error capturing function for the PODs on the fabric card.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-ERR_GASPP_INIT

Cannot initialize CLI access to POD registers. Pod type ([dec]) rc([hex]) [chars]

Explanation The sfe-drvr process cannot initialize the infrastructure allow read/write access to the POD registers on the fabric card.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-ERR_INTERNAL_SW

[chars] rc [hex] [chars]

Explanation The 140G fabric POD DLL encountered the annunciated internal SW error. It likely affects the operation of the fabric POD and the fabric subsystem on the multi-chassis.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-HIGH_2_5VCC

[chars] POD detects HIGH 2.5Vcc. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a high in 2.5Vcc voltage. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-HIGH_3_3VCC

[chars] POD detects HIGH 3.3Vcc. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a high in 3.3Vcc voltage. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-HIGH_TEMP

[chars] POD detects HIGH temperature. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a high temperature. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-LOW_2_5VCC

[chars] POD detects LOW 2.5Vcc. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a low in 2.5Vcc voltage. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-LOW_3_3VCC

[chars] POD detects LOW 3.3Vcc. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a low in 3.3Vcc voltage. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-LOW_TEMP

[chars] POD detects LOW temperature. Board([chars]) [chars] Pod([dec]) [chars]

Explanation The POD detects a low temperature. The POD might not be functioning properly, and can cause cell drops or corruption in the rx or tx link associated with the POD.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-RX_CH_HI_PWR

Rx POD detects HIGH power on Board([chars]) Rx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The POD detects a high power on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption from received cells.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-RX_CH_LO_PWR

Rx POD detects LOW power on Board([chars]) Rx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The POD detects a low power on a channel. This is a precursor to Rx LOS errors in the channel. The link is now marginal, and the superstar Rx link may be seeing correctable errors. Although the link is still working, it is marginal and can become inoperational in due course. This is also likely due to contaminates in the optical cable and/or connector. Please check if the optical cable and/or connector are secured, and clean the components as necessary.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-RX_CH_LOS_ERR

Rx POD detects loss of signal on Board([chars]) Rx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec]

Explanation The Rx POD detects a loss of signal on a channel. This can be due to: [1] The link is configured by software to be receiving cells with an invalid transmit end [2] The link is not physically connect to the Tx side. For [1], it is a software bug where a Rx link should only be configured if it has a valid transmit end. For [2], if the Rx channel suddenly sees this without any physical change of the optical cable or shut down of the other end, then it is likely the POD channel has become defective. If the optical cable connecting the POD is cut, then the Rx POD will see loss of signal.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-SPUR_INTR

Spurious interrupt (with zero value in interrupt status) on Board([chars]) [chars] Pod([dec]) interrupt line.

Explanation An interrupt is generated but the interrupt status register indicates no pending interrupts. This may be due to a hardware error where the interrupt line is stuck in its active state i.e. active low.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-TX_CH_HI_BIAS_CURRENT

Tx POD detects HIGH bias current on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The Tx POD detects a high bias current on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption in the downstream.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-TX_CH_HI_PWR

Tx POD detects HIGH power on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The POD detects a high power on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption in the downstream.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-TX_CH_LO_BIAS_CURRENT

Tx POD detects LOW bias current on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The Tx POD detects a low bias current on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption in the downstream.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-TX_CH_LO_PWR

Tx POD detects LOW power on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec] [chars]

Explanation The POD detects a low power on a channel. The channel may not be functioning properly, and can cause cell drops, or corruption in the downstream. This is a precursor to the Tx LOS.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-TX_CH_LOS_ERR

Tx POD detects loss of signal on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec]

Explanation The Tx POD detects a loss of signal on a channel. This can be due to: [1] A valid superstar Tx link is not powered on by software [2] An invalid superstar Tx link has the corresponding Tx POD channel configured [3] A valid superstar Tx link has malfunction or the Tx channel has malfunction to not receive signals from the superstar Tx link.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-UNSUPP_RX_CH

Rx POD detects an unknown error type([dec]) on Board([chars]) Rx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec]

Explanation The Rx POD detects an unknown error on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption from received cells. There can also be a software bug such that the error is not handled

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-UNSUPP_RX_NON_CH

Rx POD detects an unknown error type([dec]) on Board([chars]) Rx Pod([dec])

Explanation The Rx POD detects an unknown error on a pod. The pod might not be functioning properly, and can cause cell drops, or corruption from received cells. There can also be a software bug such that the error is not handled

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-UNSUPP_TX_CH

Tx POD detects an unknown error type([dec]) on Board([chars]) Tx Pod([dec]) Channel([dec]): [chars]%s/[dec]/[dec]

Explanation The Tx POD detects an unknown error on a channel. The channel might not be functioning properly, and can cause cell drops, or corruption from received cells. There can also be a software bug such that the error is not handled

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-3-UNSUPP_TX_NON_CH

Tx POD detects an unknown error type([dec]) on Board([chars]) Tx Pod([dec])

Explanation The Tx POD detects an unknown error on a pod. The pod might not be functioning properly, and can cause cell drops, or corruption from received cells. There can also be a software bug such that the error is not handled

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-6-RX_ALL_CH_LOP_ERR

Rx POD detects LOP signal on Board ([chars]) Pod RX([dec]) for all channel,Check Pod RX([dec]) health to confirm.

Explanation The Rx POD detects LOP signal on all channels. Please check sh controllers fabric pod health to confirm the same.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_140G_POD-6-RX_ALL_CH_LOS_ERR

Rx POD detects LOS signal on Board ([chars]) Pod RX([dec]) for all channel,Check Pod RX([dec]) health to confirm.

Explanation The Rx POD detects a LOS signal on all channels. Please check sh controllers fabric pod health to confirm the same.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FABRIC_COMM_DRVR Messages

Error Message %FABRIC-FABRIC_COMM_DRVR-3-ERR_DRV_INIT

Initialization of fabric driver failed: [chars] ; exiting...

Explanation Fabric driver encountered the annunciated error during the driver initialization. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_COMM_DRVR-3-ERR_EVM_CREATE

SFE driver failed to create event manager for [chars].

Explanation The SFE common infra driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_COMM_DRVR-3-ERR_INTERNAL_SW

[chars]; [chars]

Explanation The SFE common infra driver driver encountered a SW error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_COMM_DRVR-3-ERR_MEM_ALLOC

SFE common infra driver was unable to allocate [dec] bytes

Explanation The SFE common infra driver was unable to allocate memory. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_COMM_DRVR-7-ERR_LTRACE_INIT

SFE common infra driver failed to initialize the ltrace file [chars]; rc equals [chars]

Explanation The SFE common infra driver could not open the ltrace buffer. The SFE common infra driver and the system should function as normal, with the exception that ltrace will not be available for sfe_drvr process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_COMM_DRVR-7-ERR_SHM_INIT

SFE common infra driver failed to initialize shm [chars]; rc equals [chars]

Explanation The SFE common infra driver could not initialize shelfmgr.

Recommended Action No action is required.

FABRIC_DRIVER_LITE Messages

Error Message %FABRIC-FABRIC_DRIVER_LITE-3-ERR_ASIC_ACCESS_EXCEPTION

Fabric ASIC access timed out (reported by lite process)

Explanation This indicates that the fabric ASIC failed to acknowledge an access request from the CPU. This can happen if the host CPU tries to access an address that is out of range for the ASIC. Also, accessing a register from a block that is still in the logic reset state could stall this access and subsequent accesses to the ASIC.

Recommended Action If this condition is noticed for every access to the ASIC, then the ASIC is possibly wedged. Resetting the ASIC or reloading the fabric card will help to recover from this condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRIVER_LITE-3-ERR_DRIVER_INIT

Initialization of fabric driver lite failed: [chars] ; exiting...

Explanation Fabric driver encountered the annunciated error during the driver initialization. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr_lite) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRIVER_LITE-3-ERR_EVM_CREATE

Failed to create event manager for ’[chars]’

Explanation The Fabric driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr_lite) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRIVER_LITE-3-ERR_SHMEM_INIT

Shared Memory Error: [chars]

Explanation Attempt to init/open the shared memory fails

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRIVER_LITE-3-ERR_THREAD_ATTRIBUTE

FABRIC driver lite failed to change interupt thread to an IO thread: [chars]

Explanation The Fabric driver was unable to change the interrupt thread to an IO thread. Because of this failure, the interupt thread will not be able to receive the interupt thread events. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr_lite) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRIVER_LITE-4-ERR_LTRACE_INIT

Fabric driver lite failed to initialize the ltrace - rc equals [chars]

Explanation The Fabric driver could not open/initialize the ltrace buffer. The Fabric driver and the system should stll function as normal, with the exception that ltrace will not be available for sfe_drvr process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRIVER_LITE-6-ASIC_INITIALIZED

Fabric ASICs initialized (reported by lite process)

Explanation This indicates Fabric ASICs are initialized and is expected during normal operation.

Recommended Action No action is required.

FABRIC_DRVR_SHARED Messages

Error Message %FABRIC-FABRIC_DRVR_SHARED-2-ERR_SHMEM_INIT

Initialization of shared memory failed: [chars]

Explanation Fabric driver encountered the annunciated error during the shared memory initialization. The fabric driver cannot complete the initialization of the fabric ASICs.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FABRIC_DRVR Messages

Error Message %FABRIC-FABRIC_DRVR-1-ERR_BOARD_FAULT

[chars]. Register: [hex] Current Status: [hex]. Expected Status: [hex].

Explanation Fabric board is not operational due to the indicated fault. This information is extracted from the fabric PLD registers.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_BOARD_POWER_FAULT

[chars]

Explanation Fabric board is not operational due to the a power fault.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_CCTL_POWER_FAULT

Fabric CPLD detects power fault: [chars]

Explanation Fabric CPLD detects the specified power fault. If the failure is for the LTC2978 device, then this error is due to the failure of the cctl library function call.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_HALT_VIA_CPLD

Failed to halt [chars] using CPLD halt assert signal. Halting ASIC via its internal register.

Explanation The specified device could not be halted using the CPLD register. Use the fabric ASICs internal register to halt the device. This message is meant to catch specific hardware failure.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_HW_HEALTH_MON

[chars].

Explanation The fabric driver verifies the hardware interfaces between the various components on the fabric board. This is done on cold start (POST) and periodically there after. This message is annunciated when any of the tests fail.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_HW_HEALTH_MON

[chars].

Explanation The fabric driver verifies the hardware interfaces between the various components on the fabric board. This is done on cold start (POST) and periodically there after. This message is annunciated when any of the tests fail.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_HW_INIT

[chars].

Explanation The board initialization failed the specified operation while configuring the device. The driver will exit and attempt to come up again. On multiple such failures, the board will be shutdown permanently by the shelf manager.

Recommended Action Collect console logs. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_LOCALBUS_FAULT

Fabric CPLD detects localbus fault: [chars].

Explanation Fabric CPLD detects the specified local bus fault.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-1-ERR_THRESHOLD_ASIC_RESETS_REACHED

Reload fabric card as [chars] was reset for maximum allowed times ([dec])

Explanation A fabric ASIC may be reset a maximum of 5 times and thereafter the fabric driver requests for the card to be reloaded. On the fifth reset, the card is reloaded.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-2-ERR_MAINTENANCE_MODE

Failed to put card in maintenance mode by sysmgr. error code([hex]) - [chars]

Explanation Fabric driver detected hardware errors and requested sysmgr to place the card in maintenance mode. But sysmgr failed to do so. The card and its fabric ASICs should have been isolated from the system before attempting going to maintenance mode.

Recommended Action Check the health of the sysmgr process on the node. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-2-ERR_SHUTDOWN

Failed to shutdown by shelfmgr. error code([hex]) - [chars]

Explanation Fabric driver detected hardware errors and requested shelfmgr to shut down the node. But shelfmgr failed to do so. The card and its fabric ASICs should have been isolated from the system before the shutdown attempt.

Recommended Action Check the health of the shelfmgr process on the RP in its rack. If shelfmgr is healthy, and the card cannot self reload, then reload the card with the following command in admin mode: ’hw shut loc y/SMx/sp’, where x is the SM module number that generated the error, y is the rack that it is in. If manual shutdown does not work, or if the error recurs, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-BM_DEAD_NODE_FAILURE

BM Dead Node Failure Occured for Aggregation Node ([chars]) : ([chars]).

Explanation All the receive links for a particular stage have gone down triggering the ASIC to go into BM Dead Node. Software will auto recover. Dead node is expected to be seen during plane shut as well as SM OIR where it will result in all receive links of a particular stage to go down.

Recommended Action If the error is seen at steady state, software will auto recover. Verify that the fabric is stable. If fabric appears unstable, collected fabric show tech.

Error Message %FABRIC-FABRIC_DRVR-3-BM_DEAD_NODE_RECOVERY_FAILURE

BM Dead Node Recovery Failure Occured, Dead Node Status ([chars]) : ([hex]).

Explanation We were unable to recovery from dead node state. We attempted 3 times, but dead node clearning recovery is failing.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-CCI_INTR_INIT_FAIL

Fabric driver failed to initialize the CPLD interrupts with CCI: err code([hex])

Explanation Fabric driver cannot initialize the CPLD interrupts with CCI infrastructure. The node may not be able to handle CPLD interrupts.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-CCI_LIB_INIT_FAIL

Fabric driver failed to initialize the CPU Controller Interface library: err code([hex])

Explanation Fabric driver cannot initialize the CPU Controller Interface library infrastructure for CPLD initialization and handling. Fabric ASICs access is also compromised.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-CIH_LIB_INIT_FAIL

Fabric driver failed to initialize the Common Interrupt Handling library: err code([hex])

Explanation Fabric driver cannot initialize the Common Interrupt library infrastructure for interrupt and error handling and logging. The node might not be able to handle interrupts.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-DBG_TCAM_LIB_INIT_FAIL

Fabric driver failed to initialize the Debug TCAM library: err code([hex])

Explanation Fabric driver cannot initialize the Debug TCAM library. The node may be not be able to use the debug TCAM to debug cell flows through the fabric ASICs.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_FAULT

[chars]: [chars].

Explanation Fabric driver cannot proceed due to the indicated error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_FGID_SRAM_BIST_DONE

FGID SRAM BIST failed to complete for [chars]. Result of SRAM BIST: [hex]

Explanation This message is seen when the FGID SRAM BIST operation fails to complete after a request is issued to start it for the identified ASIC. The result of the BIST operation for that ASIC is also captured in the message. This condition implies that the ASIC is either not powered up or it is not properly reset at initialization.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_FGID_SRAM_BIST_PASS

FGID SRAM BIST failed for [chars]. Pass status: [hex] Expected Pass status: [hex]

Explanation This message is seen when the FGID SRAM BIST is completed without the necessary pass bits being set for the identified ASIC. Observed pass bits status and the expected status for the ASIC are also captured in the message. The pass status is a 3 bit status i.e. one per SRAM. Number of SRAMs depend on the fabric stage and the fabric board as specified below: S2 Card: 3 SRAMs i.e. SRAM A, SRAM B & SRAM C. S2 ASIC on S123 Cards (all LCC flavors): 1 SRAM i.e. SRAM A. S3 ASIC on S123 & S13 Cards (all LCC flavors): 2 SRAMs i.e. SRAM A & SRAM B. Pass status bit positions: SRAM A: bit 2 SRAM B: bit 1 SRAM C: bit 0.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_HARD_RESET

ASIC [chars] in error & halted. Hard reset to recover.

Explanation Identified Fabric ASIC experienced a severe error and is halted. Hard reset & re-initialize the ASIC to recover.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_PON_RESET

ASIC [chars] in error & halted. Power-On reset to recover.

Explanation Identified Fabric ASIC experienced a severe error and is halted. Power on reset & re-initialize the ASIC to recover.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_SCAN_UNSUPPORTED

Combined SPB-motherboard for JTAG not supported. Ensure 73 level base number is 12773

Explanation SPB is not designed for supporting SPB-motherboard JTAG operation necessary for asic scan functionality. SPB board with this support will have a 73 level base number of 12773. This value is programmed in the SPB EEPROM at locations 42 to 44.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_ASIC_SYSLOG

[[chars]]: [chars][LEAF ID: [hex]]; TYPE:[chars] [[chars]]; SYSTEM EFFECT:[chars]; ACTION TAKEN:[chars].

Explanation This message is logged whenever an ASIC detects an error. This message includes: ASIC identifier, interrupt name & its ID, Interrupt type, effect of the error on the system & the software action taken.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_BOARD_ALERT

[chars]. Current Status: [hex]. Expected Status: [hex].

Explanation Power controllers on the fabric card are raising the alerts indicating that either the voltages or temperature on the card is at its tolerance limits.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_BOARD_PLD_VERSION

Fabric Board PLD Version ([dec]) not supported. Upgrade to latest.

Explanation This indicates that the fabric board is running with PLD version that is not supported. Version lower than (0x1c) is not supported. Please upgrade to the latest PLD Version.

Recommended Action Shut down the plane associated to this fabric card, and upgrade the PLD Version of this board. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_DISPATCH_PULSE

Unable to dispatch messages due to invalid link check ([dec])

Explanation Failed to send a message due to invalid link check. Possible corruption in dispatch pulse.

Recommended Action Capture information as specified in the required_info section. Restart sfe_drvr to clear any out of sync issues.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_DRV_INIT

Initialization of fabric driver failed: [chars] ; exiting...

Explanation Fabric driver encountered the annunciated error during the driver initialization. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_DRV_INIT

Initialization of fabric driver failed: [chars] ; exiting...

Explanation Fabric driver encountered the annunciated error during the driver initialization. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_EVM_CREATE

Failed to create event manager for ’[chars]’

Explanation The Fabric driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_EVM_CREATE

Failed to create event manager for ’[chars]’

Explanation The Fabric driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_FGID_ACCESS

Fabric Board Going down. FGID access being aborted.

Explanation One or more ASICs for the stage on the fabric card are being reset. Hence this multicast FGID access operation for the specified stage is aborted. This may be seen on any SM node going down, during asic reset cleanup process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_FGID_REFRESH

Request [dec] to refresh FGID entry [hex].

Explanation An FGID entry is disabled following a parity error. A request to refresh the entry is issued.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_FGID_REFRESH_RETRY

Failed to refresh FGID entry. Reload the fabric card.

Explanation An FGID entry is disabled following a parity error. Request to refresh the entry wasn’t entertained. This will reload the fabric card to recover.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_FGID_WRITE

Device(s) being reset. [chars] FGID write to offset [hex] aborted.

Explanation One or more ASICs for the stage on the fabric card are in being reset. Hence this multicast FGID write operation for the specified stage is aborted.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_INVALID_INSTANCE

Access to invalid device id ([dec]).

Explanation This indicates that an attempt to access internal information was made to an invalid device id.

Recommended Action None. software error handling will recover.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_LIB_INIT_FAIL

Fabric driver failed to initialize ASIC error infrastructure: err code([hex])

Explanation Fabric driver cannot initialize the ASIC error infrastructure for recording ASIC errors and interrupts. The node is compromised in handling those errors.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_MAX_TOPO_TIME_OUT

Maximum attempts to receive topology information exceeded. Restarting sfe_drvr...

Explanation This indicates that the maximum tries for the driver to receive the necessary topology information to initialize the asic has exceeded. The driver will not continually re-request topology information.

Recommended Action Check if all the required fabric cards are UP and running.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_MAX_TOPO_TIME_OUT

Maximum attempts to receive topology information exceeded. Restarting sfe_drvr...

Explanation This indicates that the maximum tries for the driver to receive the necessary topology information to initialize the asic has exceeded. The driver will not continually re-request topology information.

Recommended Action Check if all the required fabric cards are UP and running.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Failed to allocate memory from Heap. This can happen during periods of intense memory resource usage or due to a memory leak - though these are extremely rare occurances. This message implies some message(s) between FSDB and SFE driver was not processed and so they might be out of sync.

Recommended Action Capture information as specified in the required_info section. Restart sfe_drvr to clear any out of sync issues.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Failed to allocate memory from Heap. This can happen during periods of intense memory resource usage or due to a memory leak - though these are extremely rare occurances. This message implies some message(s) between FSDB and SFE driver was not processed and so they might be out of sync.

Recommended Action Capture information as specified in the required_info section. Restart sfe_drvr to clear any out of sync issues.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_POD_INIT

Failed to initialize PODs - error([hex]) : [chars]; exiting...

Explanation Fabric Driver failed to initialize one of the POD hardware modules. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_POD_INIT

Failed to initialize POD for node: [hex], error : [chars]; exiting...

Explanation Fabric Driver failed to initialize one of the POD hardware modules. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_RELOAD

Failed to reload. [chars]

Explanation Fabric driver encountered an error when trying to reload. The card cannot be reloaded at the time of the message. Fabric driver may retry again when resources and conditions are met. The card and its fabric ASICs should have been isolated from the system.

Recommended Action Check the health of the shelfmgr process on the dSC RP. If shelfmgr is healthy, and the card does not reload after waiting for minutes, reload the card with the following command in admin mode: ’reload loc 0/SMx/sp’, where x is the SM module number that generated the error. If manual reload does not work, or if the error recurs, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_RMA_CARD

Persistent errors seen on ASIC [chars]. Shutdown the fabric card.

Explanation The ASIC on the fabric board is faulty and being taken out of operation.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_SELF_RELOAD

SFE driver requesting PFM to reload card

Explanation Fabric driver encountered a system error which shelfmgr cannot reload the node. The fabric driver self-reloads instead. The card and its fabric ASICs should have been isolated from the system before the self-reload.

Recommended Action Check the health of the shelfmgr process on the dSC RP. If shelfmgr is healthy, and the card cannot self reload, then reload the card with the following command in admin mode: ’reload loc y/SMx/sp’, where x is the SM module number that generated the error, and y is the rack that it is in. If manual reload does not work, or if the error recurs, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_SELF_RELOAD

Failed to reload by shelf-mgr [hex] [[chars]]. Self-reloading...

Explanation Fabric driver encountered a system error which shelf-mgr cannot reload the node. The fabric driver self-reloads instead. The card and its fabric ASICs should have been isolated from the system before the self-reload.

Recommended Action Check the health of the shelfmgr process on the dSC RP. If shelfmgr is healthy, and the card cannot self reload, then reload the card with the following command in admin mode: ’reload loc y/SMx/sp’, where x is the SM module number that generated the error, and y is the rack that it is in. If manual reload does not work, or if the error recurs, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_SPURIOUS_INTERRUPT

Spurious interrupt (with zero value in interrupt status) on [chars] interrupt line.

Explanation An interrupt is generated but the interrupt status register indicates no pending interrupts. This may be due to a hardware error where the interrupt line is stuck in its active state i.e. active low.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_SPURIOUS_INTERRUPT

Spurious interrupt (with zero value in interrupt status) on interrupt line.

Explanation An interrupt is generated but the interrupt status register indicates no pending interrupts. This may be due to a hardware error where the interrupt line is stuck in its active state i.e. active low.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_STUCK_BARRIER_FLOW

Barriers stuck for type [dec] at phase [dec] [curr: [hex] prev: [hex]] on [chars].

Explanation Barrier flow of certain type is stuck at identified phase on the specified ASIC.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_THREAD_ATTRIBUTE

FABRIC driver failed to change interupt thread to an IO thread: [chars]

Explanation The Fabric driver was unable to change the interrupt thread to an IO thread. Because of this failure, the interupt thread will not be able to receive the interupt thread events. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_THREAD_ATTRIBUTE

FABRIC driver failed to change interupt thread to an IO thread: [chars]

Explanation The Fabric driver was unable to change the interrupt thread to an IO thread. Because of this failure, the interupt thread will not be able to receive the interupt thread events. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_TIMER_START

Leaf Timer Failed to start. Timer Type: [dec].

Explanation Fabric driver could not start timer.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_WAITING_FOR_TOPO_TIMED_OUT

Driver timed out waiting for topology information. Attempt re-request for topology.

Explanation This indicates that the driver has not received the necessary topology information to initialize the asic. The driver will continually re-request topology. This message can also be seen in a multichassis system when a fabric card is pulled out or powered down and the other end is still up and running or if the plane config for this card is missing.

Recommended Action Check if all the required fabric cards are UP and running.

Error Message %FABRIC-FABRIC_DRVR-3-ERR_WAITING_FOR_TOPO_TIMED_OUT

Driver timed out waiting for topology information. Attempt re-request for topology.

Explanation This indicates that the driver has not received the necessary topology information to initialize the asic. The driver will continually re-request topology. This message can also be seen in a multichassis system when a fabric card is pulled out or powered down and the other end is still up and running or if the plane config for this card is missing.

Recommended Action Check if all the required fabric cards are UP and running.

Error Message %FABRIC-FABRIC_DRVR-3-ERRRATE_EXCEED_GLACIAL

[chars] ; Node Key equals [hex]

Explanation The Fabric driver encountered the annunciated error. For Error Node Keys - 0x1050016; 0x1050018; 0x105001A : This indicates a hardware problem in Fabric ASIC. Sysmgr will reload the node up to a fixed number of times the error is encountered, to recover. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERRRATE_EXCEED_GLACIAL

[chars] ; Node Key equals [hex]

Explanation The Fabric driver encountered the annunciated error. For Error Node Keys - 0x1050016; 0x1050018; 0x105001A : This indicates a hardware problem in Fabric ASIC. If the displayed error is one of the following ’Correctable Single-Bit Error in Cell Reference FIFO’ ’Correctable Single-Bit Error in Reference Count Table’ ’Correctable Single-Bit Error in Cell Store SRAM’ The data will be corrected. The number of correctable single-bit errors occur on reading these memory is aggregated, When the aggregate count exceeds threshold (2 in 2 days), This ios msg is reported. The shelf-mgr reloads the fabric card.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERRRATE_EXCEED_NO_LIMIT

[chars]

Explanation The fabric driver encountered the annunciated error. Sysmgr will reload the node up to a fixed number of times the error is encountered, to recover. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-ERRRATE_EXCEED_SLOW

[chars]

Explanation The fabric driver encountered the annunciated error. Sysmgr will reload the node up to a fixed number of times the error is encountered, to recover. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-FIT_INIT_FAIL

Fabric driver failed to initialize with FIT: err code([hex])

Explanation Fabric driver cannot initialize the FIT library. User will not be able to induce errors via FIT tool.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-LINK_SHUT_DOWN_PERM

Link [chars] Shutdown permanently due to [chars].

Explanation The Fabric driver encountered an error beyond the threshold times on the annunciated Fabric Switching Element link and the link is shutdown permenently by the driver.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-LM_DRAIN_QUEUE_FAILURE

sfe[[dec]]: Failed to Drain Queue Associated To Destination ([dec]) from [chars] for LM[dec] equals [[hex]].

Explanation Unable to drain all the cells from a given queue. This may cause barrier timeouts once the queue is re-enabled. Hard resetting Asic’

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-3-RCC_HW_INIT_FAIL

Fabric driver failed to initialize with RCC HW init library in RLDRAM init sequence [dec]: err code([hex])

Explanation Fabric driver cannot initialize with the RCC HW init library. Possible fabric multicast feature may not function correctly.

Recommended Action Collect all the event and console logs. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-3-RCC_LIB_INIT_FAIL

Fabric driver failed to initialize the RCC memory controller library: err code([hex])

Explanation Fabric driver cannot initialize the RCC memory controller library. The node may be not be able to initialized properly.

Recommended Action Collect all the event logs and ’sh controller fabric trace driver all location location of the node’ Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-4-CCTL_LTC2978_ALERT_DAMPENING

[chars]

Explanation This is an indication that alerts are being received from LTC2978 at a rate exceeding 15 per second causing the dampening to be triggered. Interrupt is disabled for 30seconds after which it will be re-enabled.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-4-ERR_LTRACE_INIT

Fabric driver failed to initialize the ltrace - rc equals [chars]

Explanation The Fabric driver could not open/initialize the ltrace buffer. The Fabric driver and the system should stll function as normal, with the exception that ltrace will not be available for sfe_drvr process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-4-ERR_LTRACE_INIT

Fabric driver failed to initialize the ltrace - rc equals [chars]

Explanation The Fabric driver could not open/initialize the ltrace buffer. The Fabric driver and the system should stll function as normal, with the exception that ltrace will not be available for sfe_drvr process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-4-RCC_INIT_INCOMPLETE

RCC BIST of init sequence [dec] on device [dec] running for [dec] seconds; ([hex])

Explanation Fabric drivers health is contingent of the RCC library’s initialization. Driver will poll to verify the status of the RCC hw init.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-4-WARN_HW_HEALTH_MON

[chars].

Explanation The fabric driver verifies the hardware interfaces between the various components on the fabric board. This is done on cold start (POST) and periodically there after. This message is annunciated when any of the tests fail. Failure of test doesn’t indicate the card is unusable. It may be a message suggesting an upgrade for the board.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-5-POST_FPD_OP

FPD load operation is completed & fabric ASICs will be reset & recovered.

Explanation This message posts a notice to indicate that the FPD load operation is completed and a reset of the card is required to come up with the new PLD image.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-5-PRE_FPD_OP

Fabric ASICs being halted for FPD operation.

Explanation Field upgrade of the fabric PLD while the fabric card is in the chassis. Due to a bug in the superstar ASIC, field upgrade of the PLD cannot be done while the card is in service and fabric plane is UP. It is required to halt the ASICs on the board and isolate the plane while the PLD image is being loaded via the JTAG interface. This message posts a notice to indicate that the devices will be halted.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ABORT_FGID_WRITE

Aborted FGID mcast write to [hex] as [chars] in PON reset state.

Explanation Aborted an FGID write update because the ASIC is in the reset state. This can happen when an FGID update request is in flight when the ASIC goes through a PON reset operation as a part of an error recovery. During PON reset operation, the FGID memory refresh logic is not operational and hence the write operation is not carried through. After a PON reset recovery, the connection with the FGID server is reestablished and a full FGID download is done again. Note, that this is expected only for PON reset recovery and not hard reset.

Recommended Action None

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_FREEZE_PRE_SCAN

Freeze state of ASIC [chars] before asic scan.

Explanation Freeze state of the ASIC before initiating ASIC scan.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_HALTED_VIA_CPLD

[chars] halted using CPLD halt assert signal.

Explanation The specified device is halted using the CPLD register.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_INITIALIZED

Fabric ASICs initialized

Explanation This indicates Fabric ASICs are initialized and is expected during normal operation.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_INITIALIZED

Notify FSDB that [chars] is OPER_UP.

Explanation Notify FSDB that the specified ASIC is operationally UP. This indicates that the fabric ASIC is initialized and FGID download is completed. This is expected during normal operation. On a driver restart, this message will be annunciated when the FGID download done message is received.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_PON_RESET_POST_SCAN

Power-On reset ASIC [chars] to recover after asic scan.

Explanation Recover identified ASIC with a power on reset following ASIC scan.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_READ_ACCESS

ASIC: [chars] - read register access [hex] failed

Explanation This indicates a failed access to the ASIC.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_RESET_REASONS

ASIC bit mask: Ready:[hex] Reset:[hex] Halted:[hex] Not Ready:[hex] Init Fail: [hex]

Explanation This message is seen when fabric ASIC require to be reset during a driver restart. The output contains the a bit mask depiction of all ASICs on the fabric board. ’Ready’ and ’Reset’ masks identifies the ASICs that are in ready or reset state. ’Halt’, ’Not ready’ and ’Init fail’ provide additional information if the ’Reset’ mask is non-zero.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_RESET_REASONS

ASIC bit mask: Ready: [hex] Reset: [hex] Pending interrupt: [hex] Ready bits: [hex].

Explanation This message is seen when fabric ASIC require to be reset during a driver restart. The output contains the a bit mask depiction of all ASICs on the fabric board. ’Ready’ and ’Reset’ masks identifies the ASICs that are in ready or reset state. If an ASIC is in reset state, pending interrupt captures additional information.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ASIC_WRITE_ACCESS

ASIC: [chars] - write value [hex] register access [hex] failed

Explanation This indicates a failed access to the ASIC.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-AWAIT_FGID_DOWNLOAD

Await FGID download completion to notify FSDB of ASIC initialization.

Explanation This indicates Fabric ASICs are initialized pending the FGID download done notification from FGID server. FSDB will be notified about the ASIC initialization complete state only after the ASICs are initialized and the FGID download is completed.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-BARRIER_FLOW_STARTED

Barrier flow started on all ASICs

Explanation Barriers started flowing on all the nodes/types.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-BUS_STALL_ADDR_TRACEBACK

Traceback on an address [hex] detected earlier to cause bus stall interrupt.

Explanation Certain address accesses were causing bus stall interrupts on the superstar ASIC. Such addresses are cached by the driver. Subsequently, when these addresses are accessed by the driver, this message is logged to provide a traceback information to help with debugging.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-CARD_RELOAD_POST_SCAN

Reloading the card to recover after asic scan.

Explanation Recover the card with reload following ASIC scan.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-DLL_LOAD

SEA ASIC driver loaded

Explanation Fabric driver loaded for the SEA asics.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-ERR_ASIC_ACCESS_TIMED_OUT

Access to [chars] timed out. Device will be PON reset to recover.

Explanation Sometimes, when the register access of the superstar ASIC fails, read of any of its registers returns 0xdeaddead. Now if this happens when CIH is processing an interrupt, CIH would accidentally determine the source of the interrupt as Rx Snoop SRAM SBE interrupt. In reality, this interrupt is not even enabled by the driver. The Rx snoop SRAM SBE interrupt is obtained if we traverse the interrupt tree of the superstar ASIC as given below: - Bit 0 of the top level CPU hierarchy interrupt is Rx block. - Bit 0 of the Rx block hierarchy is Rx block leaf interrupts. - Bit 0 of the Rx block leaf interrupts in Rx Snoop SRAM SBE.

Recommended Action If this condition is noticed for every access to the ASIC, then the ASIC is possibly wedged. Resetting the ASIC or reloading the fabric card will help to recover from this condition. Driver automatically tries recovering the ASIC via PON reset. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-FIT_HARD_RESET

FIT forcing hard reset of device id: [dec]

Explanation This indicates that the FIT tool has forced/induced a hard reset.

Recommended Action None.

Error Message %FABRIC-FABRIC_DRVR-6-FIT_POWER_ON_RESET

FIT forcing power on reset of device id: [dec]

Explanation This indicates that the FIT tool has forced/induced a power on reset.

Recommended Action None.

Error Message %FABRIC-FABRIC_DRVR-6-INFO_HW_HEALTH_MON

[chars].

Explanation This message is seen when any of the previously reported health monitoring error condition is cleared.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-6-MISSING_PLANE_CONFIG

Plane config is missing or inconsistent.

Explanation Missing admin plane configuration for this module.

Recommended Action Check the admin plane configuration to ensure that it corresponds with the actual physical topology of the system. If this configuration looks correct then contact support, otherwise correct the configuration and the system should recover.

Error Message %FABRIC-FABRIC_DRVR-6-MISSING_PLANE_CONFIG

Plane config is missing or inconsistent. Asic status(oper_up/avl_map) equals [hex]/[hex]. Cfg availability (topo/oob/bpe) equals [hex]/[hex]/[hex]. cfg_retrvd equals [hex]

Explanation Missing admin plane configuration for this module.

Recommended Action Check the admin plane configuration to ensure that it corresponds with the actual physical topology of the system. If this configuration looks correct then contact support, otherwise correct the configuration and the system should recover.

Error Message %FABRIC-FABRIC_DRVR-6-NODE_OIRED

OIR interrupt detected[Debug info1 equals [hex],Debug info2 equals [hex]]. sfe_drvr exited

Explanation In interrupt detecting OIR of the fabric card was received. Driver will exit. If the message is seen at steady state with no OIR action then support should be requested. In case the card was physically OIRed this message may be seen and is not an issue.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-6-NODE_RELOAD_PENDING

A request to bring down this node is pending. Node will reload in less than [dec] seconds

Explanation A node reload request to envmon is pending. If the node is not reloaded by envmon platform fault manager will be requested to bring the node down in in the time specified

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_BP_CFG

[chars]: Error in Back pressure configuration, BP Groups : [dec], [dec], [dec]

Explanation The Fabric driver encountered an error in back pressure configuration. This indicates BP configuration received from the fabric control software is incorrect. If this condition prevails, it could impact data traffic when fabric gets congested.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_BP_CFG

[chars]: Error in Back pressure configuration, BP Groups : [dec], [dec], [dec]

Explanation The Fabric driver encountered an error in back pressure configuration. This indicates BP configuration received from the fabric control software is incorrect. If this condition prevails, it could impact data traffic when fabric gets congested.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_DEBUG_REG

Fabric driver failed to register with the debug; rc equals [chars]

Explanation The Fabric driver was unable to register with the debug. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_DEBUG_REG

Fabric driver failed to register with the debug; rc equals [chars]

Explanation The Fabric driver was unable to register with the debug. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_INTERNAL_SW

[chars]

Explanation The Fabric driver encountered the annunciated internal SW error. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_INTERNAL_SW

[chars]

Explanation The Fabric driver encountered the annunciated internal SW error. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERR_LINK_TOPO

Topology mismatch for [chars]

Explanation The upstream information received from idle cells on this link does not match with FSDB information.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-ERRRATE_EXCEED_DEBUG

[chars]

Explanation The fabric driver encountered the annunciated error. If the displayed error is one of the following ’Multicast High Priority Acknowledge Barrier Timeout’ ’Multicast Low Priority Acknowledge Barrier Timeout’ ’Unicast High Priority Acknowledge Barrier Timeout’ ’Unicast Low Priority Acknowledge Barrier Timeout ’Multicast High Priority Request Barrier Timeout’ ’Multicast Low Priority Request Barrier Timeout’ ’Unicast High Priority Request Barrier Timeout’ ’Unicasts Low Priority Request Barrier Timeout’ The Fabric driver and the System should still continue to function as normal.The affected link will be identified and taken offline momentarily. These errors are expected during OIR operations. If the error happens during steady state, investigation should be done for other unexpected oir events. If there is no other unexpected oir or anything, and the issue happened 2 in 2 days, then some effort should be done to identify the source link.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-7-ERRRATE_EXCEED_DEBUG

[chars]

Explanation The fabric driver encountered the annunciated error. The Fabric driver and the System should still continue to function as normal.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_DRVR-7-LINK_SHUT_DOWN

Fabric Link: [chars] - Shutdown: [chars]

Explanation The Fabric driver encountered an error on the annunciated Fabric Switching Element link and the link is brought down.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_DRVR-7-LINK_SHUT_DOWN

Fabric Link: [chars] - Shutdown: [chars]

Explanation The Fabric driver encountered an error on the annunciated Fabric Switching Element link and the link is brought down.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FABRIC_SRVR Messages

Error Message %FABRIC-FABRIC_SRVR-1-ERR_WRONG_CHASSIS

[chars]

Explanation MINIQ Version 2 chassis type do not support sea/superstar based fabric cards. MINIQ Version 1 chassis type do not support superstar based fabric cards. This is because of unsupported backplane in these chassis.

Recommended Action Replace the chassis.

Error Message %FABRIC-FABRIC_SRVR-2-ERR_BOARD_NOT_POWERED

Voltage validation failed, card will be shutdown.

Explanation Fabric card is not powered up yet. Shut it down.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-2-ERR_SHUTDOWN

Failed to shutdown by shelf-mgr. error code([hex])

Explanation Fabric driver encountered a system error in bringing down the node through shelfmgr. The card and its fabric ASICs should have been isolated from the system before the shutdown attempt.

Recommended Action Check the health of the shelfmgr process on the dSC RP. If shelfmgr is healthy, and the card cannot self reload, then reload the card with the following command in admin mode: ’hw shut loc y/SMx/sp’, where x is the SM module number that generated the error, y is the rack that it is in. If manual shutdown does not work, or if the error recurs, call your Cisco technical support representative and provide the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_ANNOUNCE

EES announcement failed, rc equals [chars]

Explanation EES domain enabling failed. This will prevent ucd/mcd messages to be exchanged between the applications and driver.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_DLL_API_INVALID_PARAM

Invalid parameter passed to DLL API.

Explanation An invalid parameter is passed to the DLL API. Check the implementation in the process calling this API.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_DLL_API_UNSUPPORTED

[chars]

Explanation API is not supported for specified reason. Check the implementation in the process calling this API.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_DRV_INIT

Initialization of fabric driver failed: [chars] ; exiting...

Explanation Fabric driver encountered the annunciated error during the driver initialization. The System Manager process (sysmgr) will automatically respawn the (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_EES_REG

EES registration failed, rc equals [chars]

Explanation EES domain enabling failed. This will prevent ucd/mcd messages to be exchanged between the applications and driver.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_ENABLE

[chars] failed for [dec], rc equals [chars]

Explanation The driver failed to enable/disable inter-process communication with fgid_server. This will prevent ucd/mcd messages to be exchanged between fgid_server and driver.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_EVM_CREATE

Failed to create event manager for ’[chars]’

Explanation The Fabric driver was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_FGID_CONS_THREAD

Process sfe_drvr will be restarted. Asic status(oper_up/avl_map) equals [hex]/[hex]. Cfg availability (topo/oob/bpe) equals [hex]/[hex]/[hex].

Explanation This is an error message and is seen in the abnormal condition when the fgid consumer thread fails to start successfully. Fgid consumer thread will successfully start if all the asics are operationally up. If the asics do not report oper-up within the timeout period fgid_consumer thread cannot be started. As a consequence SFE Driver is restarted. avl_map is a bitmap representing all the asics that are required to be operationally up to successfully start the fgid consumer thread. The oper_up bitmap indicates the asics that are currently operationally up. The topo/oob/bpe information indicates which of the asics have received the specific (topo/oob/bpe) configuration.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_FGID_DOWNLOAD_FAILED

Initial FGID Download failed (after total delay of [dec] secs)

Explanation The message is seen when initial FGID download from the FGID server to SFE driver does not get completed even after multiple attempts to reset the EES connection. This means the communication between SFE driver and FGID driver is broken and indicates a EES transport issue.

Recommended Action Capture the output of the CLIs as specified in required_info and contact your Cisco technical support representative. Once the required information is captured, a restart of sfe_drvr process on the affected fabric card, followed by a restart of fgid_server process on the appropriate RP/DRP can be attempted to recover from this error.

Error Message %FABRIC-FABRIC_SRVR-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Failed to allocate memory from Heap. This can happen during periods of intense memory resource usage or due to a memory leak - though these are extremely rare occurances. This message implies some message(s) between FSDB and SFE driver was not processed and so they might be out of sync.

Recommended Action Capture information as specified in the required_info section. Restart sfe_drvr to clear any out of sync issues.

Error Message %FABRIC-FABRIC_SRVR-3-RESET_ALL_ASICS

FDI request to reset all the ASICs on the fabric board.

Explanation Process a request received from FSDB to reset all the ASICs on the fabric card.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-3-SIGNAL

[chars] signal received when driver is not ready. [chars]

Explanation A signal was received when the driver is not yet ready. For SIGBUS card will reload. For others the signal will be raised to the OS

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-4-ERR_ECM_CREATE

Failed to create Event Connection Manager : [chars]

Explanation The Fabric driver was unable to create an event connection manager for EDM. Fabric driver and the System should continue to function as normal, with the exception that the ’show’ commands for Fabric driver will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-4-ERR_ECM_NOTIFY

Failed to register with ECM to receive notifications : [chars]

Explanation The Fabric driver was unable register with ECM to receive notifications when the connection to Sysdb goes down/up/closed. Fabric driver and the System should continue to function as normal, with the exception that the ’show’ commands for Fabric driver will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-4-ERR_FGID_DOWNLOAD

Initial FGID Download did not complete within timeout period ([dec] secs). Retrying..

Explanation The message is seen when initial FGID download from the FGID server to SFE driver does not get completed. Generally this indicates a transient EES transport issue. The SFE driver will try to recover from this error by resetting the EES connection to FGID server.

Recommended Action There is no specific manual intervention needed to be taken by the customer for this message. As mentioned in the explanation, SFE driver will try to recover from this situation on its own. However, if this message is being seen often, then please capture the output of the CLIs mentioned in the required_info, and contact Cisco technical support representative.

Error Message %FABRIC-FABRIC_SRVR-4-ERR_LTRACE_INIT

Fabric driver failed to initialize the ltrace - rc equals [chars]

Explanation The Fabric driver could not open/initialize the ltrace buffer. The Fabric driver and the system should stll function as normal, with the exception that ltrace will not be available for sfe_drvr process.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-6-ASIC_RESET_REASONS

Asics being reset, Respawn Count equals [dec] Checkpoint status equals [dec] Interrupt Status equals [hex] ASICs are ready equals [dec]

Explanation This message is seen when fabric ASICS are being reset. The status reported here provide information about the reason for the reset.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-6-FAB_MODULE

[chars]

Explanation This is to give infomation regarding fabric module type.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-6-FABRIC_DISCOVERY

Discovered [chars] fabric

Explanation This is to give infomation regarding fabric card type.

Recommended Action No action is required.

Error Message %FABRIC-FABRIC_SRVR-6-INVALID_CARD_TYPE_ERROR

Cannot find board revision

Explanation The message is seen when we fail to read the EEPROM for board revison. Check platform libraries & i2c bus connectivity.

Recommended Action Check the EEPROM programming, environmental condition and the type of board that is inserted.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_BAG_REG

[chars]

Explanation The Fabric driver was unable to register Fabric driver bags. The Fabric driver and the System should continue to function as normal, with the exception that the ’show’ commands for Fabric driver will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_DEBUG_INIT

Fabric driver failed to initialize the debug; rc equals [chars]

Explanation The Fabric driver was unable to initialize debug. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_DEBUG_REG

Fabric driver failed to register with the debug; rc equals [chars]

Explanation The Fabric driver was unable to register with the debug. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_INTERNAL_SW

[chars]

Explanation The Fabric driver encountered the annunciated internal SW error. The System Manager process (sysmgr) will automatically respawn this (sfe_drvr) process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_PCDS_SUPPORT

[chars]

Explanation PCDS support will not be available due to the specified reason.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRIC_SRVR-7-ERR_SYSDB_EDM_REG

[chars]

Explanation The Fabric driver was unable to become an external data manager (EDM) despite having a connection to SysDB. The operation will be retried. The Fabric driver and the System should continue to function as normal, with the exception that the ’show’ commands for Fabric driver will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FABRICQ_MGR Messages

Error Message %FABRIC-FABRICQ_MGR-3-ERR_FBP_CFG

Fabricq received an invalid FBP config. [chars]

Explanation The Fabricq received an invalid FBP configuration

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ_MGR-3-ERR_INIT

Initialization Error: [chars] Reason: [chars]. Exiting.

Explanation Fabricq manager encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. Verify that the fabricq_mgr driver is up and running by executing the following command at the CLI of the active RP: ’show process fabricq_mgr location ’ If it is still non-operational, enable the following debugs of the fabricq_mgr driver process: error Errors in the driver fatal Fatal errors which cause driver to exit info All informational events init Initialization events and restart the driver by executing the following command at the CLI of the active RP: ’process restart fabricq_mgr location ’ If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-3-ERR_MEM_ALLOC

Error Allocating [dec] bytes of memory

Explanation Fabricq encountered a fatal memory allocation error. Please contact TAC support.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-3-IMDR_ABORT

Fabricq aborted the iMDR upgrade Error equals [dec] Reason: [chars]

Explanation The IngressQ process aborted the iMDR upgrade most likely due to a prior process crash.

Recommended Action Examine logs to determine if the fabricq_mgr process crashes and collect relevant crash info. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-4-ERR_CHKPT_INIT

Checkpoint Initialization failed. Reason: [chars]

Explanation Fabricq Checkpoint Init error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-4-ERR_IMDR_NOTIFY

Unexpected event received during ISSU Upgrade [chars]

Explanation The Fabricq Mgr received an event from the iMDR Mgr that it did not register for.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-4-WARN_INIT

Initialization Warning: [chars] Reason: [chars].

Explanation Fabricq manager encountered an error but was able recover or continue execution. This is not a serious or fatal error, but for informational purposes only.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_BAG_REG

Bag register failed for rules. Reason: [chars]

Explanation EDM Bags are used to share information between components using sysdb. This Error indicates that bag registration failed.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_CLIENT_REG

Client [chars] failed. Reason: [chars]

Explanation Fabricq Manager client Registration/Unregistration error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_DLL_INIT

Dll Initialization for [chars] failed. Reason: [chars]

Explanation Fabricq driver tried to register for a dll but it encountered an error. The driver might lose some of its functionality.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_EVM_CREATE

Event Manager create failed for [chars]. Reason: [chars]

Explanation Fabricq Event Manager create error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_EVM_NOTIFY

Event Manager notify failed for [chars]. Reason: [chars]

Explanation Fabricq Event Manager notify error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_LWM_EVENT_BLOCK

LWM Event Manager event block failed. Reason: [chars]

Explanation Fabricq Event Manager event block error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_LWM_REPLY

An error occurred during LWM message reply. Reason: [chars]

Explanation Fabricq LWM reply error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ_MGR-7-ERR_SYSDB_EDM_REG

Sysdb Register EDM failed. Reason: [chars]

Explanation Fabricq Sysdb Register EDM error

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FABRICQ Messages

Error Message %FABRIC-FABRICQ-1-ERR_ASIC_ERROR

Fabricq [dec]: [chars]

Explanation Fabricq encountered an ASIC error which software cannot resolve

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-1-ERR_ASIC_GENERIC

Fabric Asic [dec] encountered generic error(s). Details: [chars]

Explanation Fabricq encountered an unexpected error in asic. Software will take appropriate action to log and fix the error.

Recommended Action No action is required.

Error Message %FABRIC-FABRICQ-1-ERR_HW_DLL

Fabricq [dec]: [chars] : [chars]

Explanation Fabricq encountered an internal hardware dll api error. These type of errors are usually generated from CAI APIs. Below gives an example of where these type of error could be coming from: 1) iLite link errors 2) cci device discovery errors 3) gaspp driver init 4) cdma api errors 5) udma api errors 6) bist api errors

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-1-ERR_SW_DLL

Fabricq [dec]: [chars] : [chars]

Explanation Fabricq encountered an internal software dll api error Following are some of the reasons for this internal error: 1) mutext init 2) thread creatation 3) cai API failure

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-1-FFI_LINK_BRINGDOWN

Fabric link [dec] on ASIC [dec] is brought down due to too many [chars] errors

Explanation A fabric link was brought down due to too many errors.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-1-IO_ERROR

Fabricq [dec]: [chars]

Explanation Fabricq ASIC encountered a read or write access error or its Host Processor Interface block has gone down and come back up. The access error is classified into two classes - software or hardware. Hardware access error refers to an error at the PCI link used to connect the ASIC to the host processor. Software access error refers to the error, caused by a un-discovered software bug, which makes software to perform un-supported access to an ASIC location, like writing to a read-only location.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_ASIC_FCRAM_ASSERT

Assert error in Fabricq ASIC [dec]. FCRAM Channel [dec].

Explanation Fabricq ASIC encountered a FCRAM Channel error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-ERR_ASIC_INIT

fabricq asic [dec]: encountered [chars] during init: [chars]

Explanation Fabricq Asic driver encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_BIST

Error during [chars] BIST

Explanation Built-In Self-Test failed for Fabricq ASIC.

Recommended Action Collect output of ’show logging’, run offline diagnostics on the card and contact TAC. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_DMA

[chars]

Explanation A hardware error occurred while a DMA transfer initiated by the FQM process was taking place. This means certain data requested by the FQM process will not be available.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_INIT

Instance: [dec]. Error: [chars]

Explanation Fabricq Asic driver encountered a fatal error resulting in the restart of the fabricq_mgr driver process.

Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. Verify that the fabricq_mgr driver is up and running by executing the following command at the CLI of the active RP: ’show process fabricq_mgr location ’ If it is still non-operational, enable the following debugs of the fabricq_mgr driver process: error Errors in the driver fatal Fatal errors which cause driver to exit info All informational events init Initialization events and restart the driver by executing the following command at the CLI of the active RP: ’process restart fabricq_mgr location ’ If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_NULL_INPUT_ARGS

[chars]

Explanation Fabricq asic dll encountered an internal software API error where a NULL input parameter is used.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-3-ERR_RX_FBP

Fabricq ASIC received incorrect FBP bitmap. [chars]

Explanation The Fabricq ASIC is configured to expect fabric backpressure informtion for a particular set of groups on a small set of links. This error indicates that incoming backpressure information doesn’t match the expected config.

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-ERR_RX_FBP

Fabricq ASIC received incorrect FBP bitmap. [chars]

Explanation The Fabricq ASIC is configured to expect fabric backpressure informtion for a particular set of groups on a small set of links. This error indicates that incoming backpressure information doesn’t match the expected config.

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-PCL_CCNT_ERR

Major error in PCL of fabricq asic [dec]: [chars] data.

Explanation Sponge encountered a PCL cell count mistmatch error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-PCL_CSLOT_SYNC

Major internal error in PCL of fabricq asic [dec]: [chars].

Explanation Sponge encountered a PCL internal error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-PCL_PKT

Minor error in PCL of fabricq asic [dec]. [chars]

Explanation Sponge encountered a PCL Packet error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-PCL_XCELL_ERR

Major error in PCL of fabricq asic [dec]: [chars]

Explanation Sponge encountered a PCL extra cell error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-3-RESET

Reseting Fabricq ASIC Device [dec]. Reason: [chars]

Explanation The fabricq ASIC is reset due to the reason displayed in the message. Most often the situation recovers after ASIC reset. If the resets persists, contact technical support with the following information.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-4-ERR_ASIC_MBE

Fabricq Asic [dec] detected multibit error(s). Details: [chars]

Explanation Fabricq Asic encountered a memory uncorrectable error

Recommended Action The multi-bit errors can happen in one of many blocks of the fabricq ASIC. One of them is the Fabric Interface (FI). If these error messages are generated for short intervals for FI links when a fabric card is disabled / reloaded / OIR’ed, then they are harmless. If these messages continue for more than 2 minutes, with incrementing uncorrectable error (UCE) counters, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-4-ERR_ASIC_PARITY

Fabricq Asic [dec] detected parity error(s). Details: [chars]

Explanation Fabricq Asic encountered a parity error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-ERR_ASIC_SN_LINK

Fabricq ASIC [dec] encountered a CpuCtrl [chars] error

Explanation Fabricq ASIC encountered a CpuCtrl CRC/Sync error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-FI_LINK_ALARM

Link Alarm on Fabricq ASIC [dec] link [dec]

Explanation Fabricq ASIC encountered a link alarm

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-FI_LINK_BRINGDOWN

Fabric link [dec] on ASIC [dec] may be brought down due to too many errors

Explanation A fabric link was brought down due to too many UCE or parity errors.

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-FI_TOPOLOGY

Fabric topology inconsistency detected for ASIC [unsigned int] link [unsigned int] (observed topology information: [hex], expected: [hex])

Explanation An inconsistency between the expected and observed topologies of the fabric was detected.

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-HEALTH_MONITOR

[chars]

Explanation Fabricq driver monitors the ASIC every 5 seconds to look for any problems. If an error is reported momentarily, it could be a false positive seen during a transient state, or during oversubscription. In case, the error is seen repeatedly, please contact TAC support.

Recommended Action If the error persists, please contact TAC suppport.

Error Message %FABRIC-FABRICQ-4-MI_WEDGE

Major error in Fabricq ASIC [dec]. MI [chars] Wedged

Explanation Fabricq ASIC encountered a MI Unicast/Multicast Wedge error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-4-PSN_WRAP

Major error in PCL of Fabricq asic [dec]: [chars]. [hex] spo_pcl_mem_ppbr [hex][hex]%08x[hex]%08x[hex]%08x[hex]

Explanation Fabricq encountered a PCL Packet Sequence Wrap error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-5-ERR_RES_PROG

Error during Resource Programming [chars] [unsigned int] Reason: [chars]

Explanation An error occured while the Fabricq driver was trying to create queues for an interface. This may leave one or more interfaces out of operation.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FABRICQ-5-MI_BPDECODE

Major error in Fabricq ASIC [dec]. MI [chars] Backpressure decode error

Explanation Fabricq ASIC encountered a MI Unicast/Multicast BP Decode error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-6-ERR_ASIC_EOP

Minor error in Fabricq ASIC [dec]. [chars] End of Packet error

Explanation Fabricq ASIC encountered a Unicast/Multicast Unexpected/Missing End Of Packet error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-6-ERR_ASIC_GENERIC

Fabric Asic [dec] encountered generic error(s). Details: [chars]

Explanation Fabricq encountered an interrupt that has exceeded its threshold value. Software takes appropriate action to log and fix the error.

Recommended Action No action is required.

Error Message %FABRIC-FABRICQ-6-ERR_ASIC_OOR

Fabricq Asic [dec] encountered [chars] Out Of Resources error.

Explanation Fabricq encountered an out of resources error.

Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message %FABRIC-FABRICQ-6-ERR_ASIC_RESET_DEFERRAL

Fabricq ASIC [dec] : [chars]

Explanation The annunciated error occurred relating to asic deferral.

Recommended Action In one of the persistent storage devices (harddisk:/, disk0: etc.) on the DSC’s RP that was active at the time the message was emitted, a file may have been created under a directory called asic_snapshots/ for this occurrence. The name is of the format ’sponge_debug_snapshot.noderack_slog_CPU0.[first/latest]’ Collect that file if present and save it to the case.

Error Message %FABRIC-FABRICQ-6-ERR_ASIC_SBE

Fabricq Asic [dec] detected single bit error(s). Details: [chars]

Explanation Fabricq Asic encountered a memory correctable error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-6-SPI_FBP

Minor error: Cluster: [dec] in Fabricq ASIC [dec] has SPI FBP [chars] error

Explanation The Fabricq asic encounted a fabric backpressure error. These sort of errors are to be expected during bootup or during OIR events, and are harmless for the vast majority of the time. The only time they would signify a serious error is if they recur for long periods.

Recommended Action If these messages are recurring and/or you’re seeing other faults (such as traffic loss) then contact your support agent.

Error Message %FABRIC-FABRICQ-6-URG_CTX

Minor error in PCL of Fabricq asic [dec]. Urgent Context ([chars])

Explanation Fabricq encountered a PCL Urgent Context error

Recommended Action *SUPPORT*

Error Message %FABRIC-FABRICQ-7-ERR_DMA

Error during DMA transfer: Source Addr [hex], Dest Addr [pointer]. Reason: [chars]

Explanation An error occurred while a DMA transfer initiated by the FQM process was taking place. This means certain data requested by the FQM process will not be available.

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FDI Messages

Error Message %FABRIC-FDI-3-EES_ANNOUNCEMENT_ERR

EES Announcement Failed: [chars]

Explanation This process encountered an internal software error. [chars] provide detailed information about this error Process will restart to recover from this error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FDI-3-ERR_SEND_FAIL

Unable to send message to peer [dec]-[hex]-[dec]: [chars]

Explanation An unexpected error occurred while sending an message. Process will restart to recover from this error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FDI-3-ERR_TLV_HDR

Structure with Missing or Corrupted TLV. Previous TLV: [chars]. Current: [chars]

Explanation FSDB/Driver encountered a FDI message containing structure(s) which do not have a TLV header, or the message is too short to contain the structure(s) specified in the TLV header. This means that the TLV encoding code is missing and needs to be added to the appropriate structure. After an occurence of such error, it is likely that FSDB and Driver have gone out of sync.

Recommended Action Capture information as specified in the required_info section. Restart FSDB/appropriate driver (from whichever process context this error message was logged) to clean any ’out of sync’ issues.

Error Message %FABRIC-FDI-3-ERR_TLV_TYPE

Structure received with Invalid TLV. Previous TLV: [chars]. Current: [chars]

Explanation FSDB/Driver received a FDI message containing structure(s) with invalid TLV type. This means that the TLV encoding code is missing some structure entry. After an occurence of such error, it is likely that FSDB and Driver have gone out of sync.

Recommended Action Capture information as specified in the required_info section. Restart FSDB/appropriate driver (from whichever process context this error message was logged) to clear any ’out of sync’ issues.

FEATURE_LPTS Messages

Error Message %FABRIC-FEATURE_LPTS-3-ERR_DOUBLE_FREE

Double free of FGID [dec]

Explanation A software error occurred, when the PA attempted to double free the FGID

Recommended Action No action required Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FEATURE_LPTS-3-ERR_FGID_DB_RETRIES_EXCEEDED

Number of unknown errors from FGID-DB ([dec]) has exceeded maximum

Explanation A software error occurred, when the PA attempted to allocate FGID’s from the FGID aggregator.

Recommended Action The process will attempt to recover by restarting. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FEATURE_LPTS-3-ERR_UNALLOCATED_FREE

Attempt to free unallocated FGID [dec]

Explanation A software error occurred, when the PA attempted to free unknown FGID

Recommended Action No action required Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FEATURE_LPTS-3-ERR_UNKNOWN_FGID_DB_ERROR

Unknown error from FGID-DB, [chars] FGID [dec] [[dec]]([dec], [dec]): [chars]

Explanation A software error occurred, when the PA attempted to Allocate, free or join FGID from the FGID Aggregator.

Recommended Action The process will attempt to recover by retrying the operation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FGID_AGG Messages

Error Message %FABRIC-FGID_AGG-3-ERR_DEBUG_INIT

fgid_aggregator unable to initialize dbg ; rc equals [chars]

Explanation The FGID Aggregator was unable to initialize debug. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_EVM_CREATE

FGID Aggregator failed to create [chars] evm ; rc equals [chars]

Explanation The FGID aggregator was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_EVM_SYNC_ATTACH

FGID Aggregator failed to attach [chars] to evm ; rc equals [chars]

Explanation The FGID Aggregator was unable to attach the indicated event handler to the event manager. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_GSP

[chars]: rc equals [chars]

Explanation The FGID Aggregator was unable to create/join GSP group. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_INTERNAL_SW

[chars]; [chars]

Explanation The FGID Aggregator encountered the annunciated SW error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_MEM_ALLOC

FGID Aggregator unable to allocate [dec] bytes

Explanation The FGID Aggregator was unable to allocate memory. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-3-ERR_SYSMGR

[chars]; rc equals [chars]

Explanation The FGID Aggregator encountered the annunciated sysmgr error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_AGG-7-ERR_LTRACE_INIT

FGID Aggregator failed to initialize the ltrace file [chars] : [chars]

Explanation The FGID Aggregator Could not open the annunciated ltrace buffer. The FGID component and the system should stll function as normal, with the exception that ltrace will not be available for fgid_aggregator process.

Recommended Action No action is required.

FGID_ALLOC Messages

Error Message %FABRIC-FGID_ALLOC-3-ERR_EVM_CREATE

FGID Allocator failed to create [chars] evm; rc equals [chars]

Explanation The FGID allocator was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-3-ERR_GSP

[chars]: rc equals [chars]

Explanation The FGID Allocator encountered the annunciated GSP error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-3-ERR_INTERNAL_SW

[chars] ; rc equals [chars]

Explanation The FGID Allocator encountered the annunciated internal SW error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-3-ERR_MEM_ALLOC

FGID Allocator failed to allocate [dec] bytes

Explanation The FGID Allocator was unable to allocate memory. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-3-ERR_SYSMGR

[chars]; rc equals [chars]

Explanation The FGID Allocator encountered the annunciated sysmgr error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_BAG_REG

FGID allocator failed to register FGID bags; rc equals [chars]

Explanation The FGID allocator was unable to register FGID bags. The FGID component and the System should continue to function as normal, with the exception that the ’show’ commands for FGID allocator will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_CHKPT_INIT

FGID Allocator failed to initialize the checkpoint library ; rc equals [chars]

Explanation The FGID Allocator was unable to initialize the checkpoint library. The fgid_allocator process may need restarting, if the errors persist.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_CHKPT_ITERATE_START

FGID Allocator failed to start to iterate Checkpoint table [chars]; rc equals [chars]

Explanation The FGID Allocator was unable to start to iterate checkpoint table. The fgid_allocator process may need restarting, if the errors persist.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_CHKPT_REG

FGID Allocator failed to register the Checkpoint table [chars] ; rc equals [chars]

Explanation The FGID Allocator was unable to register the checkpoint table. The fgid_allocator process may need restarting, if the errors persist.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_DEBUG_INIT

FGID Allocator failed to initialize debug ; rc equals [chars]

Explanation The FGID Allocator failed to initialize debug. The FGID component and the System should still continue to function as normal, with the exception that the debugs will not be available fgid_allocator process.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_LTRACE_INIT

FGID Allocator failed to initialize the ltrace file [chars]; rc equals [chars]

Explanation The FGID Allocator could not open the annunciated ltrace buffer. The FGID component and the system should function as normal, with the exception that ltrace will not be available for fgid_aggregator process.

Recommended Action No action is required.

Error Message %FABRIC-FGID_ALLOC-7-ERR_SYSDB_BIND

FGID Allocator failed to bind to Sysdb name space [chars]; rc equals [chars]

Explanation The FGID-DB allocator unable to bind to sysdb name space. The fgid_allocator may need restarting if the errors persist.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_ALLOC-7-ERR_SYSDB_EDM_REG

FGID allocator failed to perform EDM registration; rc equals [chars]

Explanation The FGID allocator was unable to become an external data manager (EDM) despite having a connection to SysDB. The operation will be retried. The FGID component and the System should continue to function as normal, with the exception that the ’show’ commands for FGID allocator will not be available.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FGID_BCDL_CONSUMER Messages

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_BCDL

[chars] ; rc equals [chars]

Explanation The BCDL Consumer process has encountered the annunciated BCDL error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_BOARD_TYPE

FGID BCDL Consumer failed to get hardware board type: rc equals [chars]

Explanation The FGID BCDL Consumer was unable to get the board type.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_DEBUG_INIT

The FGID BCDL Consumer Failed to initialize debug; rc equals [chars]

Explanation The FGID BCDL Consumer was unable to initialize debug. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_EVM

[chars] : [chars]

Explanation The FGID BCDL consumer encountered the annunciated Event Manager Error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_FDI_CLIENT_REG

Unable to perform FDI client registration; rc equals [chars]

Explanation The FGID BCDL Consumer was unable to register with the FDI client. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_FGID_DOWNLOAD_DONE_NOTIF

FGID BCDL Consumer failed to notify SFE driver about FGID download complete; rc equals [chars]

Explanation The FGID BCDL Consumer encountered an error while notifying the SFE driver about FGID download completion. This indicates a problem with communication between SFE_DRVR and FGID BCDL consumer. Restart SFE driver manually.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_FGID_SET

FGID BCDL Consumer failed to set FGID [chars] bitmap; rc equals [chars]

Explanation The FGID BCDL Consumer encountered an error while setting S2 or S3 bitmap. This indicates a problem with the communication between the SFE driver and the FGID BCDL consumer. The FGID BCDL consumer and/or SEA driver may need restarting if the errors persist.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-3-ERR_RACK_NUM

FGID BCDL Consumer failed to get the rack value; rc equals [chars]

Explanation The FGID BCDL Consumer encountered an error while retrieving the rack value from nodeid. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_BCDL_CONSUMER-7-ERR_LTRACE_INIT

FGID BCDL Consumer failed to initialize the ltrace file [chars] : rc equals [chars]

Explanation The FGID BCDL Consumer could not open the annunciated ltrace buffer. The FGID component and the system should function as normal, with the exception that ltrace will not be available for FGID BCDL Consumer process.

Recommended Action No action is required.

FGID_LIB Messages

Error Message %FABRIC-FGID_LIB-7-ERR_DEBUG_INIT

FGID library failed to initialize the debug ; rc equals [chars].

Explanation The FGID library failed to initialize debug. The FGID component and the system should still function as normal, with the exception that the debugs will not be available for FGID library.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_LIB-7-ERR_LTRACE_INIT

FGID library failed to initialize the ltrace ; rc equals [chars].

Explanation The FGID library failed to initialize ltrace. The FGID component and the system should still function as normal, with the exception that the ltrace will not be available for FGID library.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FGID_SVR Messages

Error Message %FABRIC-FGID_SVR-2-ERR_EES_INIT

Rack num could not be determined, rc equals [chars]

Explanation Rack num could not be determined because platform_get_my_nodeid failed.

Recommended Action Whenever this happens, fgid_server will dump a core file. No action is required.

Error Message %FABRIC-FGID_SVR-3-ERR_BCDL

[chars]; rc equals [chars]

Explanation The FGID Server encountered the annunciated BCDL error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_DSC

Failed to register for DSC notification; rc equals [chars]

Explanation The FGID Server encountered DSC error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_EES

[chars], rc equals [chars]

Explanation Issue with EES

Recommended Action No action is required.

Error Message %FABRIC-FGID_SVR-3-ERR_EES_REQ

Please collect show tech ees, req_id equals [dec], ddt_list_count equals [dec], ddt_uc_msgs_count equals [dec]

Explanation Issue with EES

Recommended Action No action is required.

Error Message %FABRIC-FGID_SVR-3-ERR_EVM_CREATE

FGID Server failed to create [chars] evm; rc equals [chars]

Explanation The FGID Server was unable to create an event manager for processing messages and hence failed to initialize. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_EVM_SYNC_ATTACH

FGID Server failed to attach [chars] evm; rc equals [chars]

Explanation The FGID Server was unable to attach the indicated event handler to the event manager. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_GSP

[chars] ; rc equals [chars]

Explanation The FGID-DB server encountered the annunciated GSP error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_INTERNAL_SW

[chars]; [chars]

Explanation The FGID Server encountered the annunciated SW error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_INV_FGID

Invalid FGID ([dec]) at [chars]

Explanation Trying to add an out of range FGID to an array.

Recommended Action No action is required.

Error Message %FABRIC-FGID_SVR-3-ERR_INVALID_CARD_TYPE

Invalid card type equals [hex] for node equals [hex]

Explanation Fabric cards bitmap capacity cannot be determined because platform_node_get_card_type returned an unrecognized card type.

Recommended Action No action is required.

Error Message %FABRIC-FGID_SVR-3-ERR_MEM_ALLOC

FGID Server unable to allocate [dec] bytes

Explanation The FGID Server was unable to allocate memory. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-3-ERR_USAGE

FGID Server : Server Id requested [chars] is not a allowed server_id

Explanation Incorrect command line parameters were passed to the FGID Server, and so it failed to start.

Recommended Action Check the startup arguments passed to FGID-DB. A default configuration will be used if no parameters are passed. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-4-WARNING_INTERNAL_SW

[chars]; [chars]

Explanation The FGID Server encountered the annunciated SW error.

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FGID_SVR-7-ERR_LTRACE_INIT

FGID Server failed to initiaize the ltrace file [chars]; rc equals [chars]

Explanation The FGID Server Could not open the annunciated ltrace buffer. The FGID component and the system should function as normal, with the exception that ltrace will not be available for fgid_server process.

Recommended Action No action is required.

Error Message %FABRIC-FGID_SVR-7-ERR_SYSMGR

[chars] ; rc equals [chars]

Explanation The FGID-DB server failed in sysmgr API

Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FIA_API Messages

Error Message %FABRIC-FIA_API-7-ERR_ECM

Event Connection Manager (ECM) Error: [chars] : [chars]

Explanation The FIA driver client library encountered the annunciated error condition. There are 3 types of this failure. - ECM create failure: In this case the FIA driver client library will not be able to connect to the FIA driver. - Register notification handler failure: In this case the FIA driver client library will not receive notification of ECM events. - Failure to open a connection:

Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FIA Messages

Error Message %FABRIC-FIA-0-ASIC_FATAL_FAULT

Fabric interface asic ASIC[dec] encountered fatal fault [hex] - [chars]

Explanation Fabric Interface Asic encountered an internal fatal fault. Card reload is the only way to recover from this error. The format string would display which of the internal fatal error resulted in this alarm.

Recommended Action The board would get reloaded. On reload of board, run following commands from RSP ksh to decode PCDS information - pcds_decode -c FIA.pcds file pcds_decode -c PFM_NODE.pcds file. If users has auto reset option disabled in admin config, then the board would not get reloaded on its own. At this stage collect the output of ’show asic-errors fia inst all location loc’.

Error Message %FABRIC-FIA-1-ARB_SERDES_0_FAIL_0

Arbitration Serdes Link 0 Failure on FIA 0

Explanation Arbitration serdes link 0 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_0_FAIL_1

Arbitration Serdes Link 0 Failure on FIA 1

Explanation Arbitration serdes link 0 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_0_FAIL_2

Arbitration Serdes Link 0 Failure on FIA 2

Explanation Arbitration serdes link 0 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_0_FAIL_3

Arbitration Serdes Link 0 Failure on FIA 3

Explanation Arbitration serdes link 0 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_1_FAIL_0

Arbitration Serdes Link 1 Failure on FIA 0

Explanation Arbitration serdes link 1 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_1_FAIL_1

Arbitration Serdes Link 1 Failure on FIA 1

Explanation Arbitration serdes link 1 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_1_FAIL_2

Arbitration Serdes Link 1 Failure on FIA 2

Explanation Arbitration serdes link 1 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ARB_SERDES_1_FAIL_3

Arbitration Serdes Link 1 Failure on FIA 3

Explanation Arbitration serdes link 1 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ASIC_INIT_ERR_0

Crossbar fabric interface ASIC-0 init error

Explanation Crossbar fabric interface ASIC-0 failed during init.

Recommended Action Reboot the board. If the error persists, contact TAC. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ASIC_INIT_ERR_1

Crossbar fabric interface ASIC-1 init error

Explanation Crossbar fabric interface ASIC-1 failed during init.

Recommended Action Reboot the board. If the error persists, contact TAC. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ASIC_INIT_ERR_2

Crossbar fabric interface ASIC-2 init error

Explanation Crossbar fabric interface ASIC-2 failed during init.

Recommended Action Reboot the board. If the error persists, contact TAC. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-ASIC_INIT_ERR_3

Crossbar fabric interface ASIC-3 init error

Explanation Crossbar fabric interface ASIC-3 failed during init.

Recommended Action Reboot the board. If the error persists, contact TAC. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_0_FAIL_0

Data NB Serdes Link 0 Failure on FIA 0

Explanation Data north bound serdes link 0 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_0_FAIL_1

Data NB Serdes Link 0 Failure on FIA 1

Explanation Data north bound serdes link 0 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_0_FAIL_2

Data NB Serdes Link 0 Failure on FIA 2

Explanation Data north bound serdes link 0 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_0_FAIL_3

Data NB Serdes Link 0 Failure on FIA 3

Explanation Data north bound serdes link 0 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_1_FAIL_0

Data NB Serdes Link 1 Failure on FIA 0

Explanation Data north bound serdes link 1 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_1_FAIL_1

Data NB Serdes Link 1 Failure on FIA 1

Explanation Data north bound serdes link 1 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_1_FAIL_2

Data NB Serdes Link 1 Failure on FIA 2

Explanation Data north bound serdes link 1 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_1_FAIL_3

Data NB Serdes Link 1 Failure on FIA 3

Explanation Data north bound serdes link 1 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_2_FAIL_0

Data NB Serdes Link 2 Failure on FIA 0

Explanation Data north bound serdes link 2 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_2_FAIL_1

Data NB Serdes Link 2 Failure on FIA 1

Explanation Data north bound serdes link 2 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_2_FAIL_2

Data NB Serdes Link 2 Failure on FIA 2

Explanation Data north bound serdes link 2 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_2_FAIL_3

Data NB Serdes Link 2 Failure on FIA 3

Explanation Data north bound serdes link 2 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_3_FAIL_0

Data NB Serdes Link 3 Failure on FIA 0

Explanation Data north bound serdes link 3 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_3_FAIL_1

Data NB Serdes Link 3 Failure on FIA 1

Explanation Data north bound serdes link 3 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_3_FAIL_2

Data NB Serdes Link 3 Failure on FIA 2

Explanation Data north bound serdes link 3 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_NB_SERDES_3_FAIL_3

Data NB Serdes Link 3 Failure on FIA 3

Explanation Data north bound serdes link 3 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_0_FAIL_0

Data SB Serdes Link 0 Failure on FIA 0

Explanation Data south bound serdes link 0 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_0_FAIL_1

Data SB Serdes Link 0 Failure on FIA 1

Explanation Data south bound serdes link 0 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_0_FAIL_2

Data SB Serdes Link 0 Failure on FIA 2

Explanation Data south bound serdes link 0 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_0_FAIL_3

Data SB Serdes Link 0 Failure on FIA 3

Explanation Data south bound serdes link 0 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_1_FAIL_0

Data SB Serdes Link 1 Failure on FIA 0

Explanation Data south bound serdes link 1 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_1_FAIL_1

Data SB Serdes Link 1 Failure on FIA 1

Explanation Data south bound serdes link 1 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_1_FAIL_2

Data SB Serdes Link 1 Failure on FIA 2

Explanation Data south bound serdes link 1 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SB_SERDES_1_FAIL_3

Data SB Serdes Link 1 Failure on FIA 3

Explanation Data south bound serdes link 1 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_0_FAIL_0

Data Serdes Link 0 Failure on FIA 0

Explanation Data serdes link 0 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_0_FAIL_1

Data Serdes Link 0 Failure on FIA 1

Explanation Data serdes link 0 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_0_FAIL_2

Data Serdes Link 0 Failure on FIA 2

Explanation Data serdes link 0 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_0_FAIL_3

Data Serdes Link 0 Failure on FIA 3

Explanation Data serdes link 0 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_1_FAIL_0

Data Serdes Link 1 Failure on FIA 0

Explanation Data serdes link 1 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_1_FAIL_1

Data Serdes Link 1 Failure on FIA 1

Explanation Data serdes link 1 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_1_FAIL_2

Data Serdes Link 1 Failure on FIA 2

Explanation Data serdes link 1 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_1_FAIL_3

Data Serdes Link 1 Failure on FIA 3

Explanation Data serdes link 1 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_2_FAIL_0

Data Serdes Link 2 Failure on FIA 0

Explanation Data serdes link 2 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_2_FAIL_1

Data Serdes Link 2 Failure on FIA 1

Explanation Data serdes link 2 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_2_FAIL_2

Data Serdes Link 2 Failure on FIA 2

Explanation Data serdes link 2 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_2_FAIL_3

Data Serdes Link 2 Failure on FIA 3

Explanation Data serdes link 2 failure on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_3_FAIL_0

Data Serdes Link 3 Failure on FIA 0

Explanation Data serdes link 3 failure on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_3_FAIL_1

Data Serdes Link 3 Failure on FIA 1

Explanation Data serdes link 3 failure on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_3_FAIL_2

Data Serdes Link 3 Failure on FIA 2

Explanation Data serdes link 3 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-DATA_SERDES_3_FAIL_3

Data Serdes Link 3 Failure on FIA 3

Explanation Data serdes link 3 failure on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_DDRIF_0_0

Pkt Integrity Error at DDR interface from Punt/Bridge-0 FPGA on FIA 0

Explanation Packet Integrity Error at DDR interface from Punt/Bridge-0 FPGA on FIA 0.

Recommended Action Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_DDRIF_0_1

Pkt Integrity Error at DDR interface from Punt/Bridge-0 FPGA on FIA 1

Explanation Packet Integrity Error at DDR interface from Punt/Bridge-0 FPGA on FIA 0.

Recommended Action Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_DDRIF_1_0

Pkt Integrity Error at DDR interface from Punt/Bridge-1 FPGA on FIA 0

Explanation Packet Integrity Error at DDR interface from Punt/Bridge-1 FPGA on FIA 0.

Recommended Action Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_DDRIF_1_1

Pkt Integrity Error at DDR interface from Punt/Bridge-1 FPGA on FIA 1

Explanation Packet Integrity Error at DDR interface from Punt/Bridge-1 FPGA on FIA 1.

Recommended Action Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_0_0

Pkt Integrity Error at link interface# 0 from NP/MUX on FIA 0

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 0.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_0_1

Pkt Integrity Error at link interface# 0 from NP/MUX on FIA 1

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 1.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_0_2

Pkt Integrity Error at link interface# 0 from NP/MUX on FIA 2

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 2.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_0_3

Pkt Integrity Error at link interface# 0 from NP/MUX on FIA 3

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 3.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_1_0

Pkt Integrity Error at link interface# 1 from NP/MUX on FIA 0

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 0.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_1_1

Pkt Integrity Error at link interface# 1 from NP/MUX on FIA 1

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 1.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_1_2

Pkt Integrity Error at link interface# 1 from NP/MUX on FIA 0

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 2.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-PKT_INT_ERR_AT_ILIF_1_3

Pkt Integrity Error at link interface# 1 from NP/MUX on FIA 3

Explanation Packet Integrity Error at link nterface from NP/MUX on FIA 3.

Recommended Action Verify correct link serdes error Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_ORUN_0

SKT_AB_INTR_FIFO_ORUN on FIA 0

Explanation SKT_AB_INTR_FIFO_ORUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_ORUN_1

SKT_AB_INTR_FIFO_ORUN on FIA 1

Explanation SKT_AB_INTR_FIFO_ORUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_ORUN_2

SKT_AB_INTR_FIFO_ORUN on FIA 2

Explanation SKT_AB_INTR_FIFO_ORUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_ORUN_3

SKT_AB_INTR_FIFO_ORUN on FIA 3

Explanation SKT_AB_INTR_FIFO_ORUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_URUN_0

SKT_AB_INTR_FIFO_URUN on FIA 0

Explanation SKT_AB_INTR_FIFO_URUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_URUN_1

SKT_AB_INTR_FIFO_URUN on FIA 1

Explanation SKT_AB_INTR_FIFO_URUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_URUN_2

SKT_AB_INTR_FIFO_URUN on FIA 2

Explanation SKT_AB_INTR_FIFO_URUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_FIFO_URUN_3

SKT_AB_INTR_FIFO_URUN on FIA 3

Explanation SKT_AB_INTR_FIFO_URUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN0_0

SKT_AB_INTR_IFIFO_ORUN0 on FIA 0

Explanation SKT_AB_INTR_IFIFO_ORUN0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN0_1

SKT_AB_INTR_IFIFO_ORUN0 on FIA 1

Explanation SKT_AB_INTR_IFIFO_ORUN0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN0_2

SKT_AB_INTR_IFIFO_ORUN0 on FIA 2

Explanation SKT_AB_INTR_IFIFO_ORUN0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN0_3

SKT_AB_INTR_IFIFO_ORUN0 on FIA 3

Explanation SKT_AB_INTR_IFIFO_ORUN0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN1_0

SKT_AB_INTR_IFIFO_ORUN1 on FIA 0

Explanation SKT_AB_INTR_IFIFO_ORUN1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN1_1

SKT_AB_INTR_IFIFO_ORUN1 on FIA 1

Explanation SKT_AB_INTR_IFIFO_ORUN1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN1_2

SKT_AB_INTR_IFIFO_ORUN1 on FIA 2

Explanation SKT_AB_INTR_IFIFO_ORUN1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_AB_INTR_IFIFO_ORUN1_3

SKT_AB_INTR_IFIFO_ORUN1 on FIA 3

Explanation SKT_AB_INTR_IFIFO_ORUN1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_PA_STALLED_0

SKT_BA_INTR_PA_STALLED on FIA 0

Explanation SKT_BA_INTR_PA_STALLED interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_PA_STALLED_1

SKT_BA_INTR_PA_STALLED on FIA 1

Explanation SKT_BA_INTR_PA_STALLED interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_PA_STALLED_2

SKT_BA_INTR_PA_STALLED on FIA 2

Explanation SKT_BA_INTR_PA_STALLED interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_PA_STALLED_3

SKT_BA_INTR_PA_STALLED on FIA 3

Explanation SKT_BA_INTR_PA_STALLED interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_QUEUE_LEN_URUN_0

SKT_BA_INTR_QUEUE_LEN_URUN on FIA 0

Explanation SKT_BA_INTR_QUEUE_LEN_URUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_QUEUE_LEN_URUN_1

SKT_BA_INTR_QUEUE_LEN_URUN on FIA 1

Explanation SKT_BA_INTR_QUEUE_LEN_URUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_QUEUE_LEN_URUN_2

SKT_BA_INTR_QUEUE_LEN_URUN on FIA 2

Explanation SKT_BA_INTR_QUEUE_LEN_URUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_BA_INTR_QUEUE_LEN_URUN_3

SKT_BA_INTR_QUEUE_LEN_URUN on FIA 3

Explanation SKT_BA_INTR_QUEUE_LEN_URUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_CR_INTR_CR_AB_FC_0

SKT_CR_INTR_CR_AB_FC on FIA 0

Explanation SKT_CR_INTR_CR_AB_FC interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_CR_INTR_CR_AB_FC_1

SKT_CR_INTR_CR_AB_FC on FIA 1

Explanation SKT_CR_INTR_CR_AB_FC interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_CR_INTR_CR_AB_FC_2

SKT_CR_INTR_CR_AB_FC on FIA 2

Explanation SKT_CR_INTR_CR_AB_FC interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_CR_INTR_CR_AB_FC_3

SKT_CR_INTR_CR_AB_FC on FIA 3

Explanation SKT_CR_INTR_CR_AB_FC interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_FIFO_URUN_0

SKT_DM_INTR_FIFO_URUN on FIA 0

Explanation SKT_DM_INTR_FIFO_URUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_FIFO_URUN_1

SKT_DM_INTR_FIFO_URUN on FIA 1

Explanation SKT_DM_INTR_FIFO_URUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_FIFO_URUN_2

SKT_DM_INTR_FIFO_URUN on FIA 2

Explanation SKT_DM_INTR_FIFO_URUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_FIFO_URUN_3

SKT_DM_INTR_FIFO_URUN on FIA 3

Explanation SKT_DM_INTR_FIFO_URUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_VM_IFIFO_ORUN_0

SKT_DM_INTR_VM_IFIFO_ORUN on FIA 0

Explanation SKT_DM_INTR_VM_IFIFO_ORUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_VM_IFIFO_ORUN_1

SKT_DM_INTR_VM_IFIFO_ORUN on FIA 1

Explanation SKT_DM_INTR_VM_IFIFO_ORUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_VM_IFIFO_ORUN_2

SKT_DM_INTR_VM_IFIFO_ORUN on FIA 2

Explanation SKT_DM_INTR_VM_IFIFO_ORUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_DM_INTR_VM_IFIFO_ORUN_3

SKT_DM_INTR_VM_IFIFO_ORUN on FIA 3

Explanation SKT_DM_INTR_VM_IFIFO_ORUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_BUFFER_HANG_0

SKT_ED_SCH_INTR_MC_BUFFER_HANG on FIA 0

Explanation SKT_ED_SCH_INTR_MC_BUFFER_HANG interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_BUFFER_HANG_1

SKT_ED_SCH_INTR_MC_BUFFER_HANG on FIA 1

Explanation SKT_ED_SCH_INTR_MC_BUFFER_HANG interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_BUFFER_HANG_2

SKT_ED_SCH_INTR_MC_BUFFER_HANG on FIA 2

Explanation SKT_ED_SCH_INTR_MC_BUFFER_HANG interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_BUFFER_HANG_3

SKT_ED_SCH_INTR_MC_BUFFER_HANG on FIA 3

Explanation SKT_ED_SCH_INTR_MC_BUFFER_HANG interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_QTYPE_HANG_0

SKT_ED_SCH_INTR_MC_QTYPE_HANG on FIA 0

Explanation SKT_ED_SCH_INTR_MC_QTYPE_HANG interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_QTYPE_HANG_1

SKT_ED_SCH_INTR_MC_QTYPE_HANG on FIA 1

Explanation SKT_ED_SCH_INTR_MC_QTYPE_HANG interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_QTYPE_HANG_2

SKT_ED_SCH_INTR_MC_QTYPE_HANG on FIA 2

Explanation SKT_ED_SCH_INTR_MC_QTYPE_HANG interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_MC_QTYPE_HANG_3

SKT_ED_SCH_INTR_MC_QTYPE_HANG on FIA 3

Explanation SKT_ED_SCH_INTR_MC_QTYPE_HANG interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_UC_QTYPE_HANG_0

SKT_ED_SCH_INTR_UC_QTYPE_HANG on FIA 0

Explanation SKT_ED_SCH_INTR_UC_QTYPE_HANG interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_UC_QTYPE_HANG_1

SKT_ED_SCH_INTR_UC_QTYPE_HANG on FIA 1

Explanation SKT_ED_SCH_INTR_UC_QTYPE_HANG interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_UC_QTYPE_HANG_2

SKT_ED_SCH_INTR_UC_QTYPE_HANG on FIA 2

Explanation SKT_ED_SCH_INTR_UC_QTYPE_HANG interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ED_SCH_INTR_UC_QTYPE_HANG_3

SKT_ED_SCH_INTR_UC_QTYPE_HANG on FIA 3

Explanation SKT_ED_SCH_INTR_UC_QTYPE_HANG interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC16_CHK_ERR_0

SKT_ET0_INTR_CRC16_CHK_ERR on FIA 0

Explanation SKT_ET0_INTR_CRC16_CHK_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC16_CHK_ERR_1

SKT_ET0_INTR_CRC16_CHK_ERR on FIA 1

Explanation SKT_ET0_INTR_CRC16_CHK_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC16_CHK_ERR_2

SKT_ET0_INTR_CRC16_CHK_ERR on FIA 2

Explanation SKT_ET0_INTR_CRC16_CHK_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC16_CHK_ERR_3

SKT_ET0_INTR_CRC16_CHK_ERR on FIA 3

Explanation SKT_ET0_INTR_CRC16_CHK_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC32_CHK_ERR_0

SKT_ET0_INTR_CRC32_CHK_ERR on FIA 0

Explanation SKT_ET0_INTR_CRC32_CHK_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC32_CHK_ERR_1

SKT_ET0_INTR_CRC32_CHK_ERR on FIA 1

Explanation SKT_ET0_INTR_CRC32_CHK_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC32_CHK_ERR_2

SKT_ET0_INTR_CRC32_CHK_ERR on FIA 2

Explanation SKT_ET0_INTR_CRC32_CHK_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_CRC32_CHK_ERR_3

SKT_ET0_INTR_CRC32_CHK_ERR on FIA 3

Explanation SKT_ET0_INTR_CRC32_CHK_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_HDR_CSUM_ERR_0

SKT_ET0_INTR_HDR_CSUM_ERR on FIA 0

Explanation SKT_ET0_INTR_HDR_CSUM_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_HDR_CSUM_ERR_1

SKT_ET0_INTR_HDR_CSUM_ERR on FIA 1

Explanation SKT_ET0_INTR_HDR_CSUM_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_HDR_CSUM_ERR_2

SKT_ET0_INTR_HDR_CSUM_ERR on FIA 2

Explanation SKT_ET0_INTR_HDR_CSUM_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_HDR_CSUM_ERR_3

SKT_ET0_INTR_HDR_CSUM_ERR on FIA 3

Explanation SKT_ET0_INTR_HDR_CSUM_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_EOP_0

SKT_ET0_INTR_MISSING_EOP on FIA 0

Explanation SKT_ET0_INTR_MISSING_EOP interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_EOP_1

SKT_ET0_INTR_MISSING_EOP on FIA 1

Explanation SKT_ET0_INTR_MISSING_EOP interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_EOP_2

SKT_ET0_INTR_MISSING_EOP on FIA 2

Explanation SKT_ET0_INTR_MISSING_EOP interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_EOP_3

SKT_ET0_INTR_MISSING_EOP on FIA 3

Explanation SKT_ET0_INTR_MISSING_EOP interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_SOP_0

SKT_ET0_INTR_MISSING_SOP on FIA 0

Explanation SKT_ET0_INTR_MISSING_SOP interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_SOP_1

SKT_ET0_INTR_MISSING_SOP on FIA 1

Explanation SKT_ET0_INTR_MISSING_SOP interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_SOP_2

SKT_ET0_INTR_MISSING_SOP on FIA 2

Explanation SKT_ET0_INTR_MISSING_SOP interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_MISSING_SOP_3

SKT_ET0_INTR_MISSING_SOP on FIA 3

Explanation SKT_ET0_INTR_MISSING_SOP interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_SOP_ERR_0

SKT_ET0_INTR_SOP_ERR on FIA 0

Explanation SKT_ET0_INTR_SOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_SOP_ERR_1

SKT_ET0_INTR_SOP_ERR on FIA 1

Explanation SKT_ET0_INTR_SOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_SOP_ERR_2

SKT_ET0_INTR_SOP_ERR on FIA 2

Explanation SKT_ET0_INTR_SOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET0_INTR_SOP_ERR_3

SKT_ET0_INTR_SOP_ERR on FIA 3

Explanation SKT_ET0_INTR_SOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC16_CHK_ERR_0

SKT_ET1_INTR_CRC16_CHK_ERR on FIA 0

Explanation SKT_ET1_INTR_CRC16_CHK_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC16_CHK_ERR_1

SKT_ET1_INTR_CRC16_CHK_ERR on FIA 1

Explanation SKT_ET1_INTR_CRC16_CHK_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC16_CHK_ERR_2

SKT_ET1_INTR_CRC16_CHK_ERR on FIA 2

Explanation SKT_ET1_INTR_CRC16_CHK_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC16_CHK_ERR_3

SKT_ET1_INTR_CRC16_CHK_ERR on FIA 3

Explanation SKT_ET1_INTR_CRC16_CHK_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC32_CHK_ERR_0

SKT_ET1_INTR_CRC32_CHK_ERR on FIA 0

Explanation SKT_ET1_INTR_CRC32_CHK_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC32_CHK_ERR_1

SKT_ET1_INTR_CRC32_CHK_ERR on FIA 1

Explanation SKT_ET1_INTR_CRC32_CHK_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC32_CHK_ERR_2

SKT_ET1_INTR_CRC32_CHK_ERR on FIA 2

Explanation SKT_ET1_INTR_CRC32_CHK_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_CRC32_CHK_ERR_3

SKT_ET1_INTR_CRC32_CHK_ERR on FIA 3

Explanation SKT_ET1_INTR_CRC32_CHK_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_HDR_CSUM_ERR_0

SKT_ET1_INTR_HDR_CSUM_ERR on FIA 0

Explanation SKT_ET1_INTR_HDR_CSUM_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_HDR_CSUM_ERR_1

SKT_ET1_INTR_HDR_CSUM_ERR on FIA 1

Explanation SKT_ET1_INTR_HDR_CSUM_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_HDR_CSUM_ERR_2

SKT_ET1_INTR_HDR_CSUM_ERR on FIA 2

Explanation SKT_ET1_INTR_HDR_CSUM_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_HDR_CSUM_ERR_3

SKT_ET1_INTR_HDR_CSUM_ERR on FIA 3

Explanation SKT_ET1_INTR_HDR_CSUM_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_EOP_0

SKT_ET1_INTR_MISSING_EOP on FIA 0

Explanation SKT_ET1_INTR_MISSING_EOP interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_EOP_1

SKT_ET1_INTR_MISSING_EOP on FIA 1

Explanation SKT_ET1_INTR_MISSING_EOP interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_EOP_2

SKT_ET1_INTR_MISSING_EOP on FIA 2

Explanation SKT_ET1_INTR_MISSING_EOP interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_EOP_3

SKT_ET1_INTR_MISSING_EOP on FIA 3

Explanation SKT_ET1_INTR_MISSING_EOP interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_SOP_0

SKT_ET1_INTR_MISSING_SOP on FIA 0

Explanation SKT_ET1_INTR_MISSING_SOP interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_SOP_1

SKT_ET1_INTR_MISSING_SOP on FIA 1

Explanation SKT_ET1_INTR_MISSING_SOP interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_SOP_2

SKT_ET1_INTR_MISSING_SOP on FIA 2

Explanation SKT_ET1_INTR_MISSING_SOP interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_MISSING_SOP_3

SKT_ET1_INTR_MISSING_SOP on FIA 3

Explanation SKT_ET1_INTR_MISSING_SOP interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_SOP_ERR_0

SKT_ET1_INTR_SOP_ERR on FIA 0

Explanation SKT_ET1_INTR_SOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_SOP_ERR_1

SKT_ET1_INTR_SOP_ERR on FIA 1

Explanation SKT_ET1_INTR_SOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_SOP_ERR_2

SKT_ET1_INTR_SOP_ERR on FIA 2

Explanation SKT_ET1_INTR_SOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_ET1_INTR_SOP_ERR_3

SKT_ET1_INTR_SOP_ERR on FIA 3

Explanation SKT_ET1_INTR_SOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_EOP_ERR_0

SKT_FI_INTR_RCTL0_HI_EOP_ERR on FIA 0

Explanation SKT_FI_INTR_RCTL0_HI_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_EOP_ERR_1

SKT_FI_INTR_RCTL0_HI_EOP_ERR on FIA 1

Explanation SKT_FI_INTR_RCTL0_HI_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_EOP_ERR_2

SKT_FI_INTR_RCTL0_HI_EOP_ERR on FIA 2

Explanation SKT_FI_INTR_RCTL0_HI_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_EOP_ERR_3

SKT_FI_INTR_RCTL0_HI_EOP_ERR on FIA 3

Explanation SKT_FI_INTR_RCTL0_HI_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_OVERRUN_0

SKT_FI_INTR_RCTL0_HI_OVERRUN on FIA 0

Explanation SKT_FI_INTR_RCTL0_HI_OVERRUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_OVERRUN_1

SKT_FI_INTR_RCTL0_HI_OVERRUN on FIA 1

Explanation SKT_FI_INTR_RCTL0_HI_OVERRUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_OVERRUN_2

SKT_FI_INTR_RCTL0_HI_OVERRUN on FIA 2

Explanation SKT_FI_INTR_RCTL0_HI_OVERRUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_HI_OVERRUN_3

SKT_FI_INTR_RCTL0_HI_OVERRUN on FIA 3

Explanation SKT_FI_INTR_RCTL0_HI_OVERRUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_EOP_ERR_0

SKT_FI_INTR_RCTL0_LO_EOP_ERR on FIA 0

Explanation SKT_FI_INTR_RCTL0_LO_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_EOP_ERR_1

SKT_FI_INTR_RCTL0_LO_EOP_ERR on FIA 1

Explanation SKT_FI_INTR_RCTL0_LO_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_EOP_ERR_2

SKT_FI_INTR_RCTL0_LO_EOP_ERR on FIA 2

Explanation SKT_FI_INTR_RCTL0_LO_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_EOP_ERR_3

SKT_FI_INTR_RCTL0_LO_EOP_ERR on FIA 3

Explanation SKT_FI_INTR_RCTL0_LO_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_OVERRUN_0

SKT_FI_INTR_RCTL0_LO_OVERRUN on FIA 0

Explanation SKT_FI_INTR_RCTL0_LO_OVERRUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_OVERRUN_1

SKT_FI_INTR_RCTL0_LO_OVERRUN on FIA 1

Explanation SKT_FI_INTR_RCTL0_LO_OVERRUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_OVERRUN_2

SKT_FI_INTR_RCTL0_LO_OVERRUN on FIA 2

Explanation SKT_FI_INTR_RCTL0_LO_OVERRUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL0_LO_OVERRUN_3

SKT_FI_INTR_RCTL0_LO_OVERRUN on FIA 3

Explanation SKT_FI_INTR_RCTL0_LO_OVERRUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_EOP_ERR_0

SKT_FI_INTR_RCTL1_HI_EOP_ERR on FIA 0

Explanation SKT_FI_INTR_RCTL1_HI_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_EOP_ERR_1

SKT_FI_INTR_RCTL1_HI_EOP_ERR on FIA 1

Explanation SKT_FI_INTR_RCTL1_HI_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_EOP_ERR_2

SKT_FI_INTR_RCTL1_HI_EOP_ERR on FIA 2

Explanation SKT_FI_INTR_RCTL1_HI_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_EOP_ERR_3

SKT_FI_INTR_RCTL1_HI_EOP_ERR on FIA 3

Explanation SKT_FI_INTR_RCTL1_HI_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_OVERRUN_0

SKT_FI_INTR_RCTL1_HI_OVERRUN on FIA 0

Explanation SKT_FI_INTR_RCTL1_HI_OVERRUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_OVERRUN_1

SKT_FI_INTR_RCTL1_HI_OVERRUN on FIA 1

Explanation SKT_FI_INTR_RCTL1_HI_OVERRUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_OVERRUN_2

SKT_FI_INTR_RCTL1_HI_OVERRUN on FIA 2

Explanation SKT_FI_INTR_RCTL1_HI_OVERRUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_HI_OVERRUN_3

SKT_FI_INTR_RCTL1_HI_OVERRUN on FIA 3

Explanation SKT_FI_INTR_RCTL1_HI_OVERRUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_EOP_ERR_0

SKT_FI_INTR_RCTL1_LO_EOP_ERR on FIA 0

Explanation SKT_FI_INTR_RCTL1_LO_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_EOP_ERR_1

SKT_FI_INTR_RCTL1_LO_EOP_ERR on FIA 1

Explanation SKT_FI_INTR_RCTL1_LO_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_EOP_ERR_2

SKT_FI_INTR_RCTL1_LO_EOP_ERR on FIA 2

Explanation SKT_FI_INTR_RCTL1_LO_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_EOP_ERR_3

SKT_FI_INTR_RCTL1_LO_EOP_ERR on FIA 3

Explanation SKT_FI_INTR_RCTL1_LO_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_OVERRUN_0

SKT_FI_INTR_RCTL1_LO_OVERRUN on FIA 0

Explanation SKT_FI_INTR_RCTL1_LO_OVERRUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_OVERRUN_1

SKT_FI_INTR_RCTL1_LO_OVERRUN on FIA 1

Explanation SKT_FI_INTR_RCTL1_LO_OVERRUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_OVERRUN_2

SKT_FI_INTR_RCTL1_LO_OVERRUN on FIA 2

Explanation SKT_FI_INTR_RCTL1_LO_OVERRUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_FI_INTR_RCTL1_LO_OVERRUN_3

SKT_FI_INTR_RCTL1_LO_OVERRUN on FIA 3

Explanation SKT_FI_INTR_RCTL1_LO_OVERRUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_ACCPT_TBL_DROP_ERR_0

SKT_IR0_INTR_ACCPT_TBL_DROP_ERR on FIA 0

Explanation SKT_IR0_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_ACCPT_TBL_DROP_ERR_1

SKT_IR0_INTR_ACCPT_TBL_DROP_ERR on FIA 1

Explanation SKT_IR0_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_ACCPT_TBL_DROP_ERR_2

SKT_IR0_INTR_ACCPT_TBL_DROP_ERR on FIA 2

Explanation SKT_IR0_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_ACCPT_TBL_DROP_ERR_3

SKT_IR0_INTR_ACCPT_TBL_DROP_ERR on FIA 3

Explanation SKT_IR0_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MAX_DROP_ERR_0

SKT_IR0_INTR_DC3_MAX_DROP_ERR on FIA 0

Explanation SKT_IR0_INTR_DC3_MAX_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MAX_DROP_ERR_1

SKT_IR0_INTR_DC3_MAX_DROP_ERR on FIA 1

Explanation SKT_IR0_INTR_DC3_MAX_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MAX_DROP_ERR_2

SKT_IR0_INTR_DC3_MAX_DROP_ERR on FIA 2

Explanation SKT_IR0_INTR_DC3_MAX_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MAX_DROP_ERR_3

SKT_IR0_INTR_DC3_MAX_DROP_ERR on FIA 3

Explanation SKT_IR0_INTR_DC3_MAX_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MIN_DROP_ERR_0

SKT_IR0_INTR_DC3_MIN_DROP_ERR on FIA 0

Explanation SKT_IR0_INTR_DC3_MIN_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MIN_DROP_ERR_1

SKT_IR0_INTR_DC3_MIN_DROP_ERR on FIA 1

Explanation SKT_IR0_INTR_DC3_MIN_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MIN_DROP_ERR_2

SKT_IR0_INTR_DC3_MIN_DROP_ERR on FIA 2

Explanation SKT_IR0_INTR_DC3_MIN_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_DC3_MIN_DROP_ERR_3

SKT_IR0_INTR_DC3_MIN_DROP_ERR on FIA 3

Explanation SKT_IR0_INTR_DC3_MIN_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FC_BUF_OVFLOW_0

SKT_IR0_INTR_FC_BUF_OVFLOW on FIA 0

Explanation SKT_IR0_INTR_FC_BUF_OVFLOW interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FC_BUF_OVFLOW_1

SKT_IR0_INTR_FC_BUF_OVFLOW on FIA 1

Explanation SKT_IR0_INTR_FC_BUF_OVFLOW interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FC_BUF_OVFLOW_2

SKT_IR0_INTR_FC_BUF_OVFLOW on FIA 2

Explanation SKT_IR0_INTR_FC_BUF_OVFLOW interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FC_BUF_OVFLOW_3

SKT_IR0_INTR_FC_BUF_OVFLOW on FIA 3

Explanation SKT_IR0_INTR_FC_BUF_OVFLOW interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_ORUN_0

SKT_IR0_INTR_FIFO_ORUN on FIA 0

Explanation SKT_IR0_INTR_FIFO_ORUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_ORUN_1

SKT_IR0_INTR_FIFO_ORUN on FIA 1

Explanation SKT_IR0_INTR_FIFO_ORUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_ORUN_2

SKT_IR0_INTR_FIFO_ORUN on FIA 2

Explanation SKT_IR0_INTR_FIFO_ORUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_ORUN_3

SKT_IR0_INTR_FIFO_ORUN on FIA 3

Explanation SKT_IR0_INTR_FIFO_ORUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_URUN_0

SKT_IR0_INTR_FIFO_URUN on FIA 0

Explanation SKT_IR0_INTR_FIFO_URUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_URUN_1

SKT_IR0_INTR_FIFO_URUN on FIA 1

Explanation SKT_IR0_INTR_FIFO_URUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_URUN_2

SKT_IR0_INTR_FIFO_URUN on FIA 2

Explanation SKT_IR0_INTR_FIFO_URUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_FIFO_URUN_3

SKT_IR0_INTR_FIFO_URUN on FIA 3

Explanation SKT_IR0_INTR_FIFO_URUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_PKT_EOP_ERR_0

SKT_IR0_INTR_PKT_EOP_ERR on FIA 0

Explanation SKT_IR0_INTR_PKT_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_PKT_EOP_ERR_1

SKT_IR0_INTR_PKT_EOP_ERR on FIA 1

Explanation SKT_IR0_INTR_PKT_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_PKT_EOP_ERR_2

SKT_IR0_INTR_PKT_EOP_ERR on FIA 2

Explanation SKT_IR0_INTR_PKT_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_PKT_EOP_ERR_3

SKT_IR0_INTR_PKT_EOP_ERR on FIA 3

Explanation SKT_IR0_INTR_PKT_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_SHORTKT_DROP_ERR_0

SKT_IR0_INTR_SHORTKT_DROP_ERR on FIA 0

Explanation SKT_IR0_INTR_SHORTKT_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_SHORTKT_DROP_ERR_1

SKT_IR0_INTR_SHORTKT_DROP_ERR on FIA 1

Explanation SKT_IR0_INTR_SHORTKT_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_SHORTKT_DROP_ERR_2

SKT_IR0_INTR_SHORTKT_DROP_ERR on FIA 2

Explanation SKT_IR0_INTR_SHORTKT_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR0_INTR_SHORTKT_DROP_ERR_3

SKT_IR0_INTR_SHORTKT_DROP_ERR on FIA 3

Explanation SKT_IR0_INTR_SHORTKT_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_ACCPT_TBL_DROP_ERR_0

SKT_IR1_INTR_ACCPT_TBL_DROP_ERR on FIA 0

Explanation SKT_IR1_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_ACCPT_TBL_DROP_ERR_1

SKT_IR1_INTR_ACCPT_TBL_DROP_ERR on FIA 1

Explanation SKT_IR1_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_ACCPT_TBL_DROP_ERR_2

SKT_IR1_INTR_ACCPT_TBL_DROP_ERR on FIA 2

Explanation SKT_IR1_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_ACCPT_TBL_DROP_ERR_3

SKT_IR1_INTR_ACCPT_TBL_DROP_ERR on FIA 3

Explanation SKT_IR1_INTR_ACCPT_TBL_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MAX_DROP_ERR_0

SKT_IR1_INTR_DC3_MAX_DROP_ERR on FIA 0

Explanation SKT_IR1_INTR_DC3_MAX_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MAX_DROP_ERR_1

SKT_IR1_INTR_DC3_MAX_DROP_ERR on FIA 1

Explanation SKT_IR1_INTR_DC3_MAX_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MAX_DROP_ERR_2

SKT_IR1_INTR_DC3_MAX_DROP_ERR on FIA 2

Explanation SKT_IR1_INTR_DC3_MAX_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MAX_DROP_ERR_3

SKT_IR1_INTR_DC3_MAX_DROP_ERR on FIA 3

Explanation SKT_IR1_INTR_DC3_MAX_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MIN_DROP_ERR_0

SKT_IR1_INTR_DC3_MIN_DROP_ERR on FIA 0

Explanation SKT_IR1_INTR_DC3_MIN_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MIN_DROP_ERR_1

SKT_IR1_INTR_DC3_MIN_DROP_ERR on FIA 1

Explanation SKT_IR1_INTR_DC3_MIN_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MIN_DROP_ERR_2

SKT_IR1_INTR_DC3_MIN_DROP_ERR on FIA 2

Explanation SKT_IR1_INTR_DC3_MIN_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_DC3_MIN_DROP_ERR_3

SKT_IR1_INTR_DC3_MIN_DROP_ERR on FIA 3

Explanation SKT_IR1_INTR_DC3_MIN_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FC_BUF_OVFLOW_0

SKT_IR1_INTR_FC_BUF_OVFLOW on FIA 0

Explanation SKT_IR1_INTR_FC_BUF_OVFLOW interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FC_BUF_OVFLOW_1

SKT_IR1_INTR_FC_BUF_OVFLOW on FIA 1

Explanation SKT_IR1_INTR_FC_BUF_OVFLOW interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FC_BUF_OVFLOW_2

SKT_IR1_INTR_FC_BUF_OVFLOW on FIA 2

Explanation SKT_IR1_INTR_FC_BUF_OVFLOW interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FC_BUF_OVFLOW_3

SKT_IR1_INTR_FC_BUF_OVFLOW on FIA 3

Explanation SKT_IR1_INTR_FC_BUF_OVFLOW interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_ORUN_0

SKT_IR1_INTR_FIFO_ORUN on FIA 0

Explanation SKT_IR1_INTR_FIFO_ORUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_ORUN_1

SKT_IR1_INTR_FIFO_ORUN on FIA 1

Explanation SKT_IR1_INTR_FIFO_ORUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_ORUN_2

SKT_IR1_INTR_FIFO_ORUN on FIA 2

Explanation SKT_IR1_INTR_FIFO_ORUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_ORUN_3

SKT_IR1_INTR_FIFO_ORUN on FIA 3

Explanation SKT_IR1_INTR_FIFO_ORUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_URUN_0

SKT_IR1_INTR_FIFO_URUN on FIA 0

Explanation SKT_IR1_INTR_FIFO_URUN interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_URUN_1

SKT_IR1_INTR_FIFO_URUN on FIA 1

Explanation SKT_IR1_INTR_FIFO_URUN interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_URUN_2

SKT_IR1_INTR_FIFO_URUN on FIA 2

Explanation SKT_IR1_INTR_FIFO_URUN interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_FIFO_URUN_3

SKT_IR1_INTR_FIFO_URUN on FIA 3

Explanation SKT_IR1_INTR_FIFO_URUN interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_PKT_EOP_ERR_0

SKT_IR1_INTR_PKT_EOP_ERR on FIA 0

Explanation SKT_IR1_INTR_PKT_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_PKT_EOP_ERR_1

SKT_IR1_INTR_PKT_EOP_ERR on FIA 1

Explanation SKT_IR1_INTR_PKT_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_PKT_EOP_ERR_2

SKT_IR1_INTR_PKT_EOP_ERR on FIA 2

Explanation SKT_IR1_INTR_PKT_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_PKT_EOP_ERR_3

SKT_IR1_INTR_PKT_EOP_ERR on FIA 3

Explanation SKT_IR1_INTR_PKT_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_SHORTKT_DROP_ERR_0

SKT_IR1_INTR_SHORTKT_DROP_ERR on FIA 0

Explanation SKT_IR1_INTR_SHORTKT_DROP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_SHORTKT_DROP_ERR_1

SKT_IR1_INTR_SHORTKT_DROP_ERR on FIA 1

Explanation SKT_IR1_INTR_SHORTKT_DROP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_SHORTKT_DROP_ERR_2

SKT_IR1_INTR_SHORTKT_DROP_ERR on FIA 2

Explanation SKT_IR1_INTR_SHORTKT_DROP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_IR1_INTR_SHORTKT_DROP_ERR_3

SKT_IR1_INTR_SHORTKT_DROP_ERR on FIA 3

Explanation SKT_IR1_INTR_SHORTKT_DROP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_BA_STALLED_0

SKT_NI_INTR_BA_STALLED on FIA 0

Explanation SKT_NI_INTR_BA_STALLED interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_BA_STALLED_1

SKT_NI_INTR_BA_STALLED on FIA 1

Explanation SKT_NI_INTR_BA_STALLED interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_BA_STALLED_2

SKT_NI_INTR_BA_STALLED on FIA 2

Explanation SKT_NI_INTR_BA_STALLED interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_BA_STALLED_3

SKT_NI_INTR_BA_STALLED on FIA 3

Explanation SKT_NI_INTR_BA_STALLED interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR0_0

SKT_NI_INTR_CRC_ERR0 on FIA 0

Explanation SKT_NI_INTR_CRC_ERR0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR0_1

SKT_NI_INTR_CRC_ERR0 on FIA 1

Explanation SKT_NI_INTR_CRC_ERR0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR0_2

SKT_NI_INTR_CRC_ERR0 on FIA 2

Explanation SKT_NI_INTR_CRC_ERR0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR0_3

SKT_NI_INTR_CRC_ERR0 on FIA 3

Explanation SKT_NI_INTR_CRC_ERR0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR1_0

SKT_NI_INTR_CRC_ERR1 on FIA 0

Explanation SKT_NI_INTR_CRC_ERR1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR1_1

SKT_NI_INTR_CRC_ERR1 on FIA 1

Explanation SKT_NI_INTR_CRC_ERR1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR1_2

SKT_NI_INTR_CRC_ERR1 on FIA 2

Explanation SKT_NI_INTR_CRC_ERR1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR1_3

SKT_NI_INTR_CRC_ERR1 on FIA 3

Explanation SKT_NI_INTR_CRC_ERR1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR2_0

SKT_NI_INTR_CRC_ERR2 on FIA 0

Explanation SKT_NI_INTR_CRC_ERR2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR2_1

SKT_NI_INTR_CRC_ERR2 on FIA 1

Explanation SKT_NI_INTR_CRC_ERR2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR2_2

SKT_NI_INTR_CRC_ERR2 on FIA 2

Explanation SKT_NI_INTR_CRC_ERR2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR2_3

SKT_NI_INTR_CRC_ERR2 on FIA 3

Explanation SKT_NI_INTR_CRC_ERR2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR3_0

SKT_NI_INTR_CRC_ERR3 on FIA 0

Explanation SKT_NI_INTR_CRC_ERR3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR3_1

SKT_NI_INTR_CRC_ERR3 on FIA 1

Explanation SKT_NI_INTR_CRC_ERR3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR3_2

SKT_NI_INTR_CRC_ERR3 on FIA 2

Explanation SKT_NI_INTR_CRC_ERR3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR3_3

SKT_NI_INTR_CRC_ERR3 on FIA 3

Explanation SKT_NI_INTR_CRC_ERR3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR4_0

SKT_NI_INTR_CRC_ERR4 on FIA 0

Explanation SKT_NI_INTR_CRC_ERR4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR4_1

SKT_NI_INTR_CRC_ERR4 on FIA 1

Explanation SKT_NI_INTR_CRC_ERR4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR4_2

SKT_NI_INTR_CRC_ERR4 on FIA 2

Explanation SKT_NI_INTR_CRC_ERR4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_CRC_ERR4_3

SKT_NI_INTR_CRC_ERR4 on FIA 3

Explanation SKT_NI_INTR_CRC_ERR4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_PW_STALLED_0

SKT_NI_INTR_PW_STALLED on FIA 0

Explanation SKT_NI_INTR_PW_STALLED interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_PW_STALLED_1

SKT_NI_INTR_PW_STALLED on FIA 1

Explanation SKT_NI_INTR_PW_STALLED interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_PW_STALLED_2

SKT_NI_INTR_PW_STALLED on FIA 2

Explanation SKT_NI_INTR_PW_STALLED interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_NI_INTR_PW_STALLED_3

SKT_NI_INTR_PW_STALLED on FIA 3

Explanation SKT_NI_INTR_PW_STALLED interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_MAX_SZ_ERR_0

SKT_PA_INTR_MAX_SZ_ERR on FIA 0

Explanation SKT_PA_INTR_MAX_SZ_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_MAX_SZ_ERR_1

SKT_PA_INTR_MAX_SZ_ERR on FIA 1

Explanation SKT_PA_INTR_MAX_SZ_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_MAX_SZ_ERR_2

SKT_PA_INTR_MAX_SZ_ERR on FIA 2

Explanation SKT_PA_INTR_MAX_SZ_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_MAX_SZ_ERR_3

SKT_PA_INTR_MAX_SZ_ERR on FIA 3

Explanation SKT_PA_INTR_MAX_SZ_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_UCFF_UDR_ERR_0

SKT_PA_INTR_UCFF_UDR_ERR on FIA 0

Explanation SKT_PA_INTR_UCFF_UDR_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_UCFF_UDR_ERR_1

SKT_PA_INTR_UCFF_UDR_ERR on FIA 1

Explanation SKT_PA_INTR_UCFF_UDR_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_UCFF_UDR_ERR_2

SKT_PA_INTR_UCFF_UDR_ERR on FIA 2

Explanation SKT_PA_INTR_UCFF_UDR_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PA_INTR_UCFF_UDR_ERR_3

SKT_PA_INTR_UCFF_UDR_ERR on FIA 3

Explanation SKT_PA_INTR_UCFF_UDR_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PR_INTR_PR_BA_PROTOCOL_ERR_0

SKT_PR_INTR_PR_BA_PROTOCOL_ERR on FIA 0

Explanation SKT_PR_INTR_PR_BA_PROTOCOL_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PR_INTR_PR_BA_PROTOCOL_ERR_1

SKT_PR_INTR_PR_BA_PROTOCOL_ERR on FIA 1

Explanation SKT_PR_INTR_PR_BA_PROTOCOL_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PR_INTR_PR_BA_PROTOCOL_ERR_2

SKT_PR_INTR_PR_BA_PROTOCOL_ERR on FIA 2

Explanation SKT_PR_INTR_PR_BA_PROTOCOL_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PR_INTR_PR_BA_PROTOCOL_ERR_3

SKT_PR_INTR_PR_BA_PROTOCOL_ERR on FIA 3

Explanation SKT_PR_INTR_PR_BA_PROTOCOL_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR_0

SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR on FIA 0

Explanation SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR_1

SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR on FIA 1

Explanation SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR_2

SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR on FIA 2

Explanation SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR_3

SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR on FIA 3

Explanation SKT_PW_INTR_HDR_PRS_CHDR_VQI_VLD_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR_0

SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR on FIA 0

Explanation SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR_1

SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR on FIA 1

Explanation SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR_2

SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR on FIA 2

Explanation SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR_3

SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR on FIA 3

Explanation SKT_PW_INTR_HDR_PRS_EOP_SOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR_0

SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR on FIA 0

Explanation SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR_1

SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR on FIA 1

Explanation SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR_2

SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR on FIA 2

Explanation SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR_3

SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR on FIA 3

Explanation SKT_PW_INTR_HDR_PRS_HDR_TYPE_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR_0

SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR on FIA 0

Explanation SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR_1

SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR on FIA 1

Explanation SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR_2

SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR on FIA 2

Explanation SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR_3

SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR on FIA 3

Explanation SKT_PW_INTR_HDR_PRS_SOP_EOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR_0

SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR on FIA 0

Explanation SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR_1

SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR on FIA 1

Explanation SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR_2

SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR on FIA 2

Explanation SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR_3

SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR on FIA 3

Explanation SKT_PW_INTR_HDR_PRS_SOP_SEEN_SOP_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_LEN_DROP_CNT_ERR_0

SKT_PW_INTR_LEN_DROP_CNT_ERR on FIA 0

Explanation SKT_PW_INTR_LEN_DROP_CNT_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_LEN_DROP_CNT_ERR_1

SKT_PW_INTR_LEN_DROP_CNT_ERR on FIA 1

Explanation SKT_PW_INTR_LEN_DROP_CNT_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_LEN_DROP_CNT_ERR_2

SKT_PW_INTR_LEN_DROP_CNT_ERR on FIA 2

Explanation SKT_PW_INTR_LEN_DROP_CNT_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_LEN_DROP_CNT_ERR_3

SKT_PW_INTR_LEN_DROP_CNT_ERR on FIA 3

Explanation SKT_PW_INTR_LEN_DROP_CNT_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_SRC_PT_MISMATCH_ERR_0

SKT_PW_INTR_SRC_PT_MISMATCH_ERR on FIA 0

Explanation SKT_PW_INTR_SRC_PT_MISMATCH_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_SRC_PT_MISMATCH_ERR_1

SKT_PW_INTR_SRC_PT_MISMATCH_ERR on FIA 1

Explanation SKT_PW_INTR_SRC_PT_MISMATCH_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_SRC_PT_MISMATCH_ERR_2

SKT_PW_INTR_SRC_PT_MISMATCH_ERR on FIA 2

Explanation SKT_PW_INTR_SRC_PT_MISMATCH_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_PW_INTR_SRC_PT_MISMATCH_ERR_3

SKT_PW_INTR_SRC_PT_MISMATCH_ERR on FIA 3

Explanation SKT_PW_INTR_SRC_PT_MISMATCH_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_DEQ_QERR_0

SKT_RA_INTR_VQI_DEQ_QERR on FIA 0

Explanation SKT_RA_INTR_VQI_DEQ_QERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_DEQ_QERR_1

SKT_RA_INTR_VQI_DEQ_QERR on FIA 1

Explanation SKT_RA_INTR_VQI_DEQ_QERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_DEQ_QERR_2

SKT_RA_INTR_VQI_DEQ_QERR on FIA 2

Explanation SKT_RA_INTR_VQI_DEQ_QERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_DEQ_QERR_3

SKT_RA_INTR_VQI_DEQ_QERR on FIA 3

Explanation SKT_RA_INTR_VQI_DEQ_QERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_ENQ_QERR_0

SKT_RA_INTR_VQI_ENQ_QERR on FIA 0

Explanation SKT_RA_INTR_VQI_ENQ_QERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_ENQ_QERR_1

SKT_RA_INTR_VQI_ENQ_QERR on FIA 1

Explanation SKT_RA_INTR_VQI_ENQ_QERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_ENQ_QERR_2

SKT_RA_INTR_VQI_ENQ_QERR on FIA 2

Explanation SKT_RA_INTR_VQI_ENQ_QERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_RA_INTR_VQI_ENQ_QERR_3

SKT_RA_INTR_VQI_ENQ_QERR on FIA 3

Explanation SKT_RA_INTR_VQI_ENQ_QERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9_0

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9_1

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9_2

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9_3

SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_0

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 0

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_1

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 1

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_2

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 2

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_3

SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 3

Explanation SKT_SMC0_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9_0

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 on FIA 0

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9_1

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 on FIA 1

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9_2

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 on FIA 2

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9_3

SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 on FIA 3

Explanation SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_CRC_TRANS_ERR_0

SKT_SMC0_INTR_CRC_TRANS_ERR on FIA 0

Explanation SKT_SMC0_INTR_CRC_TRANS_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_CRC_TRANS_ERR_1

SKT_SMC0_INTR_CRC_TRANS_ERR on FIA 1

Explanation SKT_SMC0_INTR_CRC_TRANS_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_CRC_TRANS_ERR_2

SKT_SMC0_INTR_CRC_TRANS_ERR on FIA 2

Explanation SKT_SMC0_INTR_CRC_TRANS_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_CRC_TRANS_ERR_3

SKT_SMC0_INTR_CRC_TRANS_ERR on FIA 3

Explanation SKT_SMC0_INTR_CRC_TRANS_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9_0

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 on FIA 0

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9_1

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 on FIA 1

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9_2

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 on FIA 2

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9_3

SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 on FIA 3

Explanation SKT_SMC0_INTR_DISP_ERROR_LANE_INDICATE_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9_0

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 on FIA 0

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9_1

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 on FIA 1

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9_2

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 on FIA 2

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9_3

SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 on FIA 3

Explanation SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_RX_DESKEW_ERR_0

SKT_SMC0_INTR_RX_DESKEW_ERR on FIA 0

Explanation SKT_SMC0_INTR_RX_DESKEW_ERR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_RX_DESKEW_ERR_1

SKT_SMC0_INTR_RX_DESKEW_ERR on FIA 1

Explanation SKT_SMC0_INTR_RX_DESKEW_ERR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_RX_DESKEW_ERR_2

SKT_SMC0_INTR_RX_DESKEW_ERR on FIA 2

Explanation SKT_SMC0_INTR_RX_DESKEW_ERR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_RX_DESKEW_ERR_3

SKT_SMC0_INTR_RX_DESKEW_ERR on FIA 3

Explanation SKT_SMC0_INTR_RX_DESKEW_ERR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_TSF_SOT_MISS_ERROR_0

SKT_SMC0_INTR_TSF_SOT_MISS_ERROR on FIA 0

Explanation SKT_SMC0_INTR_TSF_SOT_MISS_ERROR interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_TSF_SOT_MISS_ERROR_1

SKT_SMC0_INTR_TSF_SOT_MISS_ERROR on FIA 1

Explanation SKT_SMC0_INTR_TSF_SOT_MISS_ERROR interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_TSF_SOT_MISS_ERROR_2

SKT_SMC0_INTR_TSF_SOT_MISS_ERROR on FIA 2

Explanation SKT_SMC0_INTR_TSF_SOT_MISS_ERROR interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC0_INTR_TSF_SOT_MISS_ERROR_3

SKT_SMC0_INTR_TSF_SOT_MISS_ERROR on FIA 3

Explanation SKT_SMC0_INTR_TSF_SOT_MISS_ERROR interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9_0

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9_1

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9_2

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9_3

SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_DISPARITY_ERROR_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_5 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_6 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_7 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_8 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_0

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 0

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_1

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 1

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_2

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 2

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9_3

SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 on FIA 3

Explanation SKT_SMC1_INTR_8B10B_DECODE_OUT_OF_BAND_ERROR_9 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_0 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_1 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_11 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_12 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_13 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_14 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_15 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_2 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_3 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 0.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4_1

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 1

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 1.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4_2

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 2

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 2.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4_3

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 on FIA 3

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_4 interrupt on FIA 3.

Recommended Action Wait a few minutes. If it doesn’t recover, please reload the board using command ’reload location ’. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

Error Message %FABRIC-FIA-1-SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_5_0

SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_5 on FIA 0

Explanation SKT_SMC1_INTR_ALIGN_ERROR_LANE_INDICATE_5 interrupt on FIA 0.